ALCATEL-IND1-TIMETRA-LDP-MIB

All MIBs › ALCATEL-IND1-TIMETRA-LDP-MIB

Organization: Alcatel

Last Updated: 2008-01-01

Category: MPLS and Traffic Engineering, Vendor: Alcatel-Lucent

Description: Alcatel 7750 SR service router LDP MIB for managing MPLS Label Distribution Protocol sessions and label bindings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-TIMETRA-LDP-MIB?

ALCATEL-IND1-TIMETRA-LDP-MIB is an Alcatel-Lucent (Timetra/SROS) enterprise MIB for the 7x50 SR router family, covering the Label Distribution Protocol (LDP) used to establish MPLS label-switched paths. It exposes a general LDP table per virtual router describing administrative and operational state, the LDP LSR identifier, protocol version, FEC deaggregation setting, and keepalive/hello timer factors and timeouts. This MIB is used to monitor the software/protocol-layer status of MPLS label distribution -- specifically whether LDP is administratively and operationally up on a given virtual router, and whether keepalive/hello timers are configured consistently with neighbors -- functioning as an MPLS control-plane health MIB rather than hardware sensor telemetry. As part of the TIMETRA/SROS family it depends on and complements standard MPLS/LDP-related IETF MIBs (e.g. MPLS-LDP-STD-MIB) for broader label-switching context. It is deployed in service-provider backbone networks running Alcatel-Lucent 7x50 SR routers as part of an MPLS core. Network engineers evaluating or troubleshooting this functionality can download the ALCATEL-IND1-TIMETRA-LDP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-TIMETRA-LDP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel-Lucent 7x50 SR series routers

Monitoring Examples

An administrator would poll vRtrLdpGeneralTable (via vRtrLdpGeneralEntry rows) to check vRtrLdpGenAdminState against vRtrLdpGenOperState, revealing whether LDP is enabled but failing to reach an operational state on a given virtual router. Checking vRtrLdpGenKeepAliveTimeout and vRtrLdpGenHelloTimeout against neighboring routers helps diagnose LDP session flapping caused by timer mismatches, while vRtrLdpGenLdpLsrId confirms the LSR identity used in label distribution.

What Can Be Monitored

LDP administrative and operational state
LDP LSR identifier
protocol version
keepalive timer factor and timeout
hello timer factor and timeout
FEC deaggregation setting

Imported Objects

From ALCATEL-IND1-TIMETRA-FILTER-MIB

TFilterID
TFilterLogId

From ALCATEL-IND1-TIMETRA-GLOBAL-MIB

timetraSRMIBModules	OBJECT-IDENTITY
tmnxSRConfs	OBJECT-IDENTITY
tmnxSRNotifyPrefix	OBJECT-IDENTITY
tmnxSRObjs	OBJECT-IDENTITY

From ALCATEL-IND1-TIMETRA-SERV-MIB

SdpId
ServType
TdmOptionsCasTrunkFraming
TdmOptionsSigPkts

From ALCATEL-IND1-TIMETRA-TC-MIB

TNamedItemOrEmpty
TPolicyStatementNameOrEmpty
TmnxAdminState
TmnxOperState
TmnxServId
TmnxVRtrMplsLspID
TmnxVcId
TmnxVcType

From ALCATEL-IND1-TIMETRA-VRTR-MIB

vRtrID	OBJECT-TYPE
vRtrLdpStatus	OBJECT-TYPE

From IF-MIB

InterfaceIndexOrZero

From MPLS-LDP-MIB

MplsLdpIdentifier
MplsLsrIdentifier

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TestAndIncr
TimeInterval
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using vRtrLdpStatsOperDownEvents OID:

Select a Nokia (Alcatel-Lucent) 7750 SR-series service router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vRtrLdpStatsOperDownEvents into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of vRtrLdpStatsOperDownEvents specifies the number of times the LDP instance has gone operationally down since the instance was created. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
timetraLdpMIBModule	1.3.6.1.4.1.6527.1.1.3.8			The MIB module to manage and provision the Alcatel 7x50 LDP protocol features. Copyright 2003-2008 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
tmnxLdpAddrFecGroup	1.3.6.1.4.1.6527.3.1.1.8.2.6			The group of objects supporting management of extended LDP address FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems.
tmnxLdpAddrFecV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.25			The group of objects supporting management of extended LDP address FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems for release 5.0.
tmnxLdpAdjBackoffGroup	1.3.6.1.4.1.6527.3.1.1.8.2.10			The group of objects supporting general management of extended LDP adjacency backoff on Alcatel 7x50 SR series systems. The vRtrLdpAdjBackoffTable is not yet supported by a TiMOS release.
tmnxLdpAdjR2r1Group	1.3.6.1.4.1.6527.3.1.1.8.2.15			The group of objects supporting management of extended LDP Adjacencies for LDP sessions on Alcatel 7x50 SR series systems 2.1 Release.
tmnxLdpCepTdmFecV6v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.28			The group of objects supporting management of extended LDP CEP/TDM FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
tmnxLdpCompliances	1.3.6.1.4.1.6527.3.1.1.8.1
tmnxLdpConformance	1.3.6.1.4.1.6527.3.1.1.8
tmnxLdpGlobalV3v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.20			The group of objects supporting general management of extended LDP on Alcatel 7x50 SR series systems 3.0 release.
tmnxLdpGlobalV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.22			The group of objects supporting general management of extended LDP on Alcatel 7x50 SR series systems 5.0 release.
tmnxLdpGroups	1.3.6.1.4.1.6527.3.1.1.8.2
tmnxLdpIfV3v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.19			The group of objects supporting management of extended LDP interfaces and targeted peers on Alcatel 7x50 SR series systems 3.0 release.
tmnxLdpIfV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.23			The group of objects supporting management of extended LDP interfaces and targeted peers on Alcatel 7x50 SR series systems 5.0 release.
tmnxLdpNotificationGroup	1.3.6.1.4.1.6527.3.1.1.8.2.8			The group of notifications supporting the extended LDP feature on Alcatel 7x50 SR series systems.
tmnxLdpNotificationObjects	1.3.6.1.4.1.6527.3.1.2.8.17
tmnxLdpNotifications	1.3.6.1.4.1.6527.3.1.3.8.0
tmnxLdpNotifyObjsGroup	1.3.6.1.4.1.6527.3.1.1.8.2.7			The group of objects supporting extended LDP notifications on Alcatel 7x50 SR series systems.
tmnxLdpNotifyPrefix	1.3.6.1.4.1.6527.3.1.3.8
tmnxLdpObjs	1.3.6.1.4.1.6527.3.1.2.8
tmnxLdpObsoletedV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.27			The group of objects obsoleted on Alcatel 7x50 SR series systems 5.0 Release.
tmnxLdpObsoleteNotificationGroup	1.3.6.1.4.1.6527.3.1.1.8.2.12			The group of obsolete notifications for the extended LDP feature on Alcatel 7x50 SR series systems.
tmnxLdpObsoleteObjsGroup	1.3.6.1.4.1.6527.3.1.1.8.2.11			The group of obsolete objects for the extended LDP feature on Alcatel 7x50 SR series systems.
tmnxLdpServFec129V6v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.30			The group of objects supporting management of LDP FEC-129s sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
tmnxLdpServFecObsoletedV6v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.31			The group of objects supporting management of obsoleted LDP FEC objects on Alcatel 7x50 SR series systems release 6.0.
tmnxLdpServFecV4v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.21			The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 4.0.
tmnxLdpServFecV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.24			The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 5.0.
tmnxLdpServFecV6v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.29			The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
tmnxLdpSessionR2r1Group	1.3.6.1.4.1.6527.3.1.1.8.2.16			The group of objects supporting management of extended LDP Sessions on Alcatel 7x50 SR series systems 2.1 Release.
tmnxLdpSessionV5v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.26			The group of objects supporting management of extended LDP Sessions on Alcatel 7x50 SR series systems 5.0 Release.
tmnxLdpStaticFecV3v0Group	1.3.6.1.4.1.6527.3.1.1.8.2.17			The group of objects supporting management of LDP Static FECs on Alcatel 7x50 SR series systems 3.0 release.
tmnxLdpV4v0Compliance	1.3.6.1.4.1.6527.3.1.1.8.1.4			The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 4.0 release.
tmnxLdpV5v0Compliance	1.3.6.1.4.1.6527.3.1.1.8.1.5			The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 5.0 release.
tmnxLdpV6v0Compliance	1.3.6.1.4.1.6527.3.1.1.8.1.6			The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 6.0 release.
vLdpCepTdmFec129Entry	1.3.6.1.4.1.6527.3.1.2.8.25.1		not-accessible	Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vLdpCepTdmFec129Table. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VLdpCepTdmFec129Entry.
U32 vLdpCepTdmFec129LocalBitrate	1.3.6.1.4.1.6527.3.1.2.8.25.1.6	Unsigned32	read-only	The value of vLdpCepTdmFec129LocalBitrate indicates the local bitrate.
TDM vLdpCepTdmFec129LocalCasTrunk	1.3.6.1.4.1.6527.3.1.2.8.25.1.14	TdmOptionsCasTrunkFraming	read-only	The value of vLdpCepTdmFec129LocalCasTrunk indicates the local CE application signalling packets mode.
T/F vLdpCepTdmFec129LocalDiffTimestamp	1.3.6.1.4.1.6527.3.1.2.8.25.1.10	TruthValue	read-only	The value of vLdpCepTdmFec129LocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit.
U32 vLdpCepTdmFec129LocalPayloadSize	1.3.6.1.4.1.6527.3.1.2.8.25.1.4	Unsigned32	read-only	The value of vLdpCepTdmFec129LocalPayloadSize indicates the local payload size.
U32 vLdpCepTdmFec129LocalPayloadType	1.3.6.1.4.1.6527.3.1.2.8.25.1.18	Unsigned32	read-only	The value of vLdpCepTdmFec129LocalPayloadType indicates the local payload type.
T/F vLdpCepTdmFec129LocalRtpHeader	1.3.6.1.4.1.6527.3.1.2.8.25.1.8	TruthValue	read-only	The value of vLdpCepTdmFec129LocalRtpHeader indicates the local RTP header usage bit.
TDM vLdpCepTdmFec129LocalSigPkts	1.3.6.1.4.1.6527.3.1.2.8.25.1.12	TdmOptionsSigPkts	read-only	The value of vLdpCepTdmFec129LocalSigPkts indicates the local CE application signalling packets mode.
U32 vLdpCepTdmFec129LocalSsrcId	1.3.6.1.4.1.6527.3.1.2.8.25.1.20	Unsigned32	read-only	The value of vLdpCepTdmFec129LocalSsrcId indicates the local value of SSRC ID.
U32 vLdpCepTdmFec129LocalTimestampFreq	1.3.6.1.4.1.6527.3.1.2.8.25.1.16	Unsigned32	read-only	The value of vLdpCepTdmFec129LocalTimestampFreq indicates the local CE application signalling packets mode.
U32 vLdpCepTdmFec129RemoteBitrate	1.3.6.1.4.1.6527.3.1.2.8.25.1.7	Unsigned32	read-only	The value of vLdpCepTdmFec129RemoteBitrate indicates the remote bitrate.
TDM vLdpCepTdmFec129RemoteCasTrunk	1.3.6.1.4.1.6527.3.1.2.8.25.1.15	TdmOptionsCasTrunkFraming	read-only	The value of vLdpCepTdmFec129RemoteCasTrunk indicates the remote CE application signalling packets mode.
T/F vLdpCepTdmFec129RemoteDiffTimestamp	1.3.6.1.4.1.6527.3.1.2.8.25.1.11	TruthValue	read-only	The value of vLdpCepTdmFec129RemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit.
U32 vLdpCepTdmFec129RemotePayloadSize	1.3.6.1.4.1.6527.3.1.2.8.25.1.5	Unsigned32	read-only	The value of vLdpCepTdmFec129RemotePayloadSize indicates the remote payload size.
U32 vLdpCepTdmFec129RemotePayloadType	1.3.6.1.4.1.6527.3.1.2.8.25.1.19	Unsigned32	read-only	The value of vLdpCepTdmFec129RemotePayloadType indicates the remote payload type.
T/F vLdpCepTdmFec129RemoteRtpHeader	1.3.6.1.4.1.6527.3.1.2.8.25.1.9	TruthValue	read-only	The value of vLdpCepTdmFec129RemoteRtpHeader indicates the remote RTP header usage bit.
TDM vLdpCepTdmFec129RemoteSigPkts	1.3.6.1.4.1.6527.3.1.2.8.25.1.13	TdmOptionsSigPkts	read-only	The value of vLdpCepTdmFec129RemoteSigPkts indicates the remote CE application signalling packets mode.
U32 vLdpCepTdmFec129RemoteSsrcId	1.3.6.1.4.1.6527.3.1.2.8.25.1.21	Unsigned32	read-only	The value of vLdpCepTdmFec129RemoteSsrcId indicates the remote value of SSRC ID.
U32 vLdpCepTdmFec129RemoteTimestampFreq	1.3.6.1.4.1.6527.3.1.2.8.25.1.17	Unsigned32	read-only	The value of vLdpCepTdmFec129RemoteCasTrunk indicates the remote CE application signalling packets mode.
vLdpCepTdmFec129Table	1.3.6.1.4.1.6527.3.1.2.8.25		not-accessible	vLdpCepTdmFec129Table is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options.
TMN vLdpServFec129AgiTlv	1.3.6.1.4.1.6527.3.1.2.8.23.1.1	TmnxLdpFec129Tlv	not-accessible	The value of vLdpServFec129AgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC.
vLdpServFec129Entry	1.3.6.1.4.1.6527.3.1.2.8.23.1		not-accessible	Each row entry represents an instance of a service FEC-129 sent to or received from an LDP peer.
TMN vLdpServFec129Flags	1.3.6.1.4.1.6527.3.1.2.8.23.1.7	TmnxLdpFECFlags	read-only	The bit flags of vLdpServFec129Flags specify the characteristics of the FEC.
U32 vLdpServFec129InLabel1	1.3.6.1.4.1.6527.3.1.2.8.23.1.10	Unsigned32	read-only	The value of vLdpServFec129InLabel1 specifies the first ingress label exchanged
TMN vLdpServFec129InLabelSigStatus1	1.3.6.1.4.1.6527.3.1.2.8.23.1.29	TmnxLabelSigStatus	read-only	The value of vLdpServFec129InLabelSigStatus1 indicates the signaling status for vLdpServFec129InLabel1.
TMN vLdpServFec129InLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.23.1.11	TmnxLabelStatus	read-only	The value of vLdpServFec129InLabelStatus1 specifies the status of the ingress label 1
U32 vLdpServFec129LocalMaxCellConcat	1.3.6.1.4.1.6527.3.1.2.8.23.1.27	Unsigned32	read-only	The value of vLdpServFec129LocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
U32 vLdpServFec129LocalMTU	1.3.6.1.4.1.6527.3.1.2.8.23.1.23	Unsigned32	read-only	The value of vLdpServFec129LocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR.
U32 vLdpServFec129LocalVlanTag	1.3.6.1.4.1.6527.3.1.2.8.23.1.25	Unsigned32	read-only	The value of vLdpServFec129LocalVlanTag specifies the local tag on a VLAN VC type SDP binding.
TMN vLdpServFec129MapAgiTlv	1.3.6.1.4.1.6527.3.1.2.8.24.1.2	TmnxLdpFec129Tlv	read-only	The value of vLdpServFec129MapAgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC.
vLdpServFec129MapEntry	1.3.6.1.4.1.6527.3.1.2.8.24.1		not-accessible	Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
TMN vLdpServFec129MapSrcAiiTlv	1.3.6.1.4.1.6527.3.1.2.8.24.1.3	TmnxLdpFec129Tlv	read-only	The value of vLdpServFec129MapSrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC.
vLdpServFec129MapTable	1.3.6.1.4.1.6527.3.1.2.8.24		not-accessible	vLdpServFec129MapTable is a read-only table which maps to the vLdpServFec129Table. This table has the same indexes as the vLdpServFec129Table but the order in which these indexes are specified is different for the two tables.
TMN vLdpServFec129MapTgtAiiTlv	1.3.6.1.4.1.6527.3.1.2.8.24.1.4	TmnxLdpFec129Tlv	read-only	The value of vLdpServFec129MapTgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC.
TMN vLdpServFec129MapVcType	1.3.6.1.4.1.6527.3.1.2.8.24.1.1	TmnxVcType	read-only	The value of vLdpServFec129MapVcType specifies the VC type associated with this service FEC.
U32 vLdpServFec129NumInLabels	1.3.6.1.4.1.6527.3.1.2.8.23.1.8	Unsigned32	read-only	The value of vLdpServFec129NumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates whether vLdpServFec129InLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumInLabels is 1 then vLdpServFec129InLabel1 will contain valid label information.
U32 vLdpServFec129NumOutLabels	1.3.6.1.4.1.6527.3.1.2.8.23.1.9	Unsigned32	read-only	The value of vLdpServFec129NumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates whether vLdpServFec129OutLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumOutLabels is 1, then vLdpServFec129OutLabel1 will contain valid label information.
U32 vLdpServFec129OutLabel1	1.3.6.1.4.1.6527.3.1.2.8.23.1.20	Unsigned32	read-only	The value of vLdpServFec129OutLabel1 specifies the first egress label exchanged.
TMN vLdpServFec129OutLabelSigStatus1	1.3.6.1.4.1.6527.3.1.2.8.23.1.30	TmnxLabelSigStatus	read-only	The value of vLdpServFec129OutLabelSigStatus1 indicates the signaling status for vLdpServFec129OutLabel1.
TMN vLdpServFec129OutLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.23.1.21	TmnxLabelStatus	read-only	The value of vLdpServFec129OutLabelStatus1 specifies the status of the egress label 1
U32 vLdpServFec129RemoteMaxCellConcat	1.3.6.1.4.1.6527.3.1.2.8.23.1.28	Unsigned32	read-only	The value of vLdpServFec129RemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
U32 vLdpServFec129RemoteMTU	1.3.6.1.4.1.6527.3.1.2.8.23.1.24	Unsigned32	read-only	The value of vLdpServFec129RemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR.
U32 vLdpServFec129RemoteVlanTag	1.3.6.1.4.1.6527.3.1.2.8.23.1.26	Unsigned32	read-only	The value of vLdpServFec129RemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding.
SDP vLdpServFec129SdpId	1.3.6.1.4.1.6527.3.1.2.8.23.1.22	SdpId	read-only	The value of vLdpServFec129SdpId identifies the SDP associated with this peer.
TMN vLdpServFec129ServId	1.3.6.1.4.1.6527.3.1.2.8.23.1.5	TmnxServId	read-only	The value of vLdpServFec129ServId specifies the Service identifier associated with this service FEC.
SER vLdpServFec129ServType	1.3.6.1.4.1.6527.3.1.2.8.23.1.4	ServType	read-only	The value of vLdpServFec129ServType specifies the Service type associated with this service FEC.
TMN vLdpServFec129SrcAiiTlv	1.3.6.1.4.1.6527.3.1.2.8.23.1.2	TmnxLdpFec129Tlv	not-accessible	The value of vLdpServFec129SrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC.
vLdpServFec129Table	1.3.6.1.4.1.6527.3.1.2.8.23		not-accessible	vLdpServFec129Table is a read-only table that represents all service FEC-129s either sent to or received from an LDP peer known to the Virtual Router.
TMN vLdpServFec129TgtAiiTlv	1.3.6.1.4.1.6527.3.1.2.8.23.1.3	TmnxLdpFec129Tlv	not-accessible	The value of vLdpServFec129TgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC.
TMN vLdpServFec129VpnId	1.3.6.1.4.1.6527.3.1.2.8.23.1.6	TmnxVpnId	read-only	The value of vLdpServFec129VpnId identifies the VPN associated with the FEC.
vRtrLdpAddrFecEntry	1.3.6.1.4.1.6527.3.1.2.8.13.1		not-accessible	Each row entry represents an instance of an address FEC sent to or received from an LDP peer.
TMN vRtrLdpAddrFecFecType	1.3.6.1.4.1.6527.3.1.2.8.13.1.1	TmnxLdpFECType	not-accessible	The value of vRtrLdpAddrFecFecType specifies the FEC type.
TMN vRtrLdpAddrFecFlags	1.3.6.1.4.1.6527.3.1.2.8.13.1.4	TmnxLdpFECFlags	read-only	The bit flags of vRtrLdpAddrFecFlags specify the characteristics of the FEC.
U32 vRtrLdpAddrFecInLabel1	1.3.6.1.4.1.6527.3.1.2.8.13.1.7	Unsigned32	read-only	The value of vRtrLdpAddrFecInLabel1 specifies the first ingress label exchanged
U32 vRtrLdpAddrFecInLabel2	1.3.6.1.4.1.6527.3.1.2.8.13.1.10	Unsigned32	read-only	The value of vRtrLdpAddrFecInLabel2 specifies the second ingress label (if at all) exchanged.
U32 vRtrLdpAddrFecInLabel3	1.3.6.1.4.1.6527.3.1.2.8.13.1.13	Unsigned32	read-only	The value of vRtrLdpAddrFecInLabel3 specifies the third ingress label (if at all) exchanged.
U32 vRtrLdpAddrFecInLabel4	1.3.6.1.4.1.6527.3.1.2.8.13.1.16	Unsigned32	read-only	The value of vRtrLdpAddrFecInLabel4 specifies the fourth ingress label (if at all) exchanged.
U32 vRtrLdpAddrFecInLabel5	1.3.6.1.4.1.6527.3.1.2.8.13.1.19	Unsigned32	read-only	The value of vRtrLdpAddrFecInLabel5 specifies the fifth ingress label (if at all) exchanged.
NUM vRtrLdpAddrFecInLabelIfIndex1	1.3.6.1.4.1.6527.3.1.2.8.13.1.9	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecInLabelIfIndex1 specifies the interface index for ingress label 1
NUM vRtrLdpAddrFecInLabelIfIndex2	1.3.6.1.4.1.6527.3.1.2.8.13.1.12	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecInLabelIfIndex2 specifies the interface index for ingress label 2
NUM vRtrLdpAddrFecInLabelIfIndex3	1.3.6.1.4.1.6527.3.1.2.8.13.1.15	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecInLabelIfIndex3 specifies the interface index for ingress label 3
NUM vRtrLdpAddrFecInLabelIfIndex4	1.3.6.1.4.1.6527.3.1.2.8.13.1.18	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecInLabelIfIndex4 specifies the interface index for ingress label 4
NUM vRtrLdpAddrFecInLabelIfIndex5	1.3.6.1.4.1.6527.3.1.2.8.13.1.21	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecInLabelIfIndex5 specifies the interface index for ingress label 5
TMN vRtrLdpAddrFecInLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.13.1.8	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecInLabelStatus1 specifies the status of the ingress label 1
TMN vRtrLdpAddrFecInLabelStatus2	1.3.6.1.4.1.6527.3.1.2.8.13.1.11	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecInLabelStatus2 specifies the status of the ingress label
TMN vRtrLdpAddrFecInLabelStatus3	1.3.6.1.4.1.6527.3.1.2.8.13.1.14	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecInLabelStatus3 specifies the status of the ingress label 3
TMN vRtrLdpAddrFecInLabelStatus4	1.3.6.1.4.1.6527.3.1.2.8.13.1.17	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecInLabelStatus4 specifies the status of the ingress label 4
TMN vRtrLdpAddrFecInLabelStatus5	1.3.6.1.4.1.6527.3.1.2.8.13.1.20	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecInLabelStatus5 specifies the status of the ingress label 5
IP vRtrLdpAddrFecIpMask	1.3.6.1.4.1.6527.3.1.2.8.13.1.3	IpAddress	not-accessible	The value of vRtrLdpAddrFecIpMask specifies the IP Address Mask for this address FEC.
IP vRtrLdpAddrFecIpPrefix	1.3.6.1.4.1.6527.3.1.2.8.13.1.2	IpAddress	not-accessible	The value of vRtrLdpAddrFecIpPrefix specifies the IP Address Prefix for this address FEC.
TMN vRtrLdpAddrFecLspId	1.3.6.1.4.1.6527.3.1.2.8.13.1.42	TmnxVRtrMplsLspID	read-only	The value of vRtrLdpAddrFecLspId indicates the LSP id of the LSP associated with the specified service FEC.
vRtrLdpAddrFecMapEntry	1.3.6.1.4.1.6527.3.1.2.8.14.1		not-accessible	Each row entry represents an instance of an address FEC sent to or received from an LDP peer.
TMN vRtrLdpAddrFecMapFecType	1.3.6.1.4.1.6527.3.1.2.8.14.1.1	TmnxLdpFECType	read-only	The value of vRtrLdpAddrFecMapFecType specifies the FEC type.
IP vRtrLdpAddrFecMapIpMask	1.3.6.1.4.1.6527.3.1.2.8.14.1.3	IpAddress	read-only	The value of vRtrLdpAddrFecMapIpMask specifies the IP Address Mask for this address FEC.
IP vRtrLdpAddrFecMapIpPrefix	1.3.6.1.4.1.6527.3.1.2.8.14.1.2	IpAddress	read-only	The value of vRtrLdpAddrFecMapIpPrefix specifies the IP Address Prefix for this address FEC.
vRtrLdpAddrFecMapTable	1.3.6.1.4.1.6527.3.1.2.8.14		not-accessible	vRtrLdpAddrFecMapTable is a read-only table which maps to the vRtrLdpAddrFecTable. This table has the same indexes as the vRtrLdpAddrFecTable but the order in which these indexes are specified is different for the two tables.
U32 vRtrLdpAddrFecNumInLabels	1.3.6.1.4.1.6527.3.1.2.8.13.1.5	Unsigned32	read-only	The value of vRtrLdpAddrFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecInLabel1 thru vRtrLdpAddrFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumInLabels is 3 then vRtrLdpAddrFecInLabel1, vRtrLdpAddrFecInLabel2 and vRtrLdpAddrFecInLabel3 will contain valid label information.
U32 vRtrLdpAddrFecNumOutLabels	1.3.6.1.4.1.6527.3.1.2.8.13.1.6	Unsigned32	read-only	The value of vRtrLdpAddrFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecOutLabel1 thru vRtrLdpAddrFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumOutLabels is 3, then vRtrLdpAddrFecOutLabel1, vRtrLdpAddrFecOutLabel2 and vRtrLdpAddrFecOutLabel3 will contain valid label information.
U32 vRtrLdpAddrFecOutLabel1	1.3.6.1.4.1.6527.3.1.2.8.13.1.22	Unsigned32	read-only	The value of vRtrLdpAddrFecOutLabel1 specifies the first egress label exchanged
U32 vRtrLdpAddrFecOutLabel2	1.3.6.1.4.1.6527.3.1.2.8.13.1.26	Unsigned32	read-only	The value of vRtrLdpAddrFecOutLabel2 specifies the second egress label (if at all) exchanged.
U32 vRtrLdpAddrFecOutLabel3	1.3.6.1.4.1.6527.3.1.2.8.13.1.30	Unsigned32	read-only	The value of vRtrLdpAddrFecOutLabel3 specifies the third egress label (if at all) exchanged.
U32 vRtrLdpAddrFecOutLabel4	1.3.6.1.4.1.6527.3.1.2.8.13.1.34	Unsigned32	read-only	The value of vRtrLdpAddrFecOutLabel4 specifies the fourth egress label (if at all) exchanged.
U32 vRtrLdpAddrFecOutLabel5	1.3.6.1.4.1.6527.3.1.2.8.13.1.38	Unsigned32	read-only	The value of vRtrLdpAddrFecOutLabel5 specifies the fifth egress label (if at all) exchanged.
NUM vRtrLdpAddrFecOutLabelIfIndex1	1.3.6.1.4.1.6527.3.1.2.8.13.1.24	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecOutLabelIfIndex1 specifies the interface index for egress label 1
NUM vRtrLdpAddrFecOutLabelIfIndex2	1.3.6.1.4.1.6527.3.1.2.8.13.1.28	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecOutLabelIfIndex2 specifies the interface index for egress label 2
NUM vRtrLdpAddrFecOutLabelIfIndex3	1.3.6.1.4.1.6527.3.1.2.8.13.1.32	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecOutLabelIfIndex3 specifies the interface index for egress label 3
NUM vRtrLdpAddrFecOutLabelIfIndex4	1.3.6.1.4.1.6527.3.1.2.8.13.1.36	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecOutLabelIfIndex4 specifies the interface index for egress label 4
NUM vRtrLdpAddrFecOutLabelIfIndex5	1.3.6.1.4.1.6527.3.1.2.8.13.1.40	InterfaceIndexOrZero	read-only	The value of vRtrLdpAddrFecOutLabelIfIndex5 specifies the interface index for egress label 5
IP vRtrLdpAddrFecOutLabelNextHop1	1.3.6.1.4.1.6527.3.1.2.8.13.1.25	IpAddress	read-only	The value of vRtrLdpAddrFecOutLabelNextHop1 specifies the IP address of the next hop for egress label 1
IP vRtrLdpAddrFecOutLabelNextHop2	1.3.6.1.4.1.6527.3.1.2.8.13.1.29	IpAddress	read-only	The value of vRtrLdpAddrFecOutLabelNextHop2 specifies the IP address of the next hop for egress label 2
IP vRtrLdpAddrFecOutLabelNextHop3	1.3.6.1.4.1.6527.3.1.2.8.13.1.33	IpAddress	read-only	The value of vRtrLdpAddrFecOutLabelNextHop3 specifies the IP address of the next hop for egress label 3
IP vRtrLdpAddrFecOutLabelNextHop4	1.3.6.1.4.1.6527.3.1.2.8.13.1.37	IpAddress	read-only	The value of vRtrLdpAddrFecOutLabelNextHop4 specifies the IP address of the next hop for egress label 4
IP vRtrLdpAddrFecOutLabelNextHop5	1.3.6.1.4.1.6527.3.1.2.8.13.1.41	IpAddress	read-only	The value of vRtrLdpAddrFecOutLabelNextHop5 specifies the IP address of the next hop for egress label 5
TMN vRtrLdpAddrFecOutLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.13.1.23	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecOutLabelStatus1 specifies the status of the egress label 1
TMN vRtrLdpAddrFecOutLabelStatus2	1.3.6.1.4.1.6527.3.1.2.8.13.1.27	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecOutLabelStatus2 specifies the status of the egress label 2
TMN vRtrLdpAddrFecOutLabelStatus3	1.3.6.1.4.1.6527.3.1.2.8.13.1.31	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecOutLabelStatus3 specifies the status of the egress label 3
TMN vRtrLdpAddrFecOutLabelStatus4	1.3.6.1.4.1.6527.3.1.2.8.13.1.35	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecOutLabelStatus4 specifies the status of the egress label 4
TMN vRtrLdpAddrFecOutLabelStatus5	1.3.6.1.4.1.6527.3.1.2.8.13.1.39	TmnxLabelStatus	read-only	The value of vRtrLdpAddrFecOutLabelStatus5 specifies the status of the egress label 5
vRtrLdpAddrFecTable	1.3.6.1.4.1.6527.3.1.2.8.13		not-accessible	vRtrLdpAddrFecTable is a read-only table that represents all address FECs either sent to or received from an LDP peer known to the Virtual Router.
vRtrLdpAdjBackoffEntry	1.3.6.1.4.1.6527.3.1.2.8.15.1		not-accessible	A row in this table contains backoff information about an LDP adjacency. When an LDP session startup fails for the first time, the LDP entity waits for a certain time interval before it tries to setup the session again. This interval is the backoff interval. The initial value for the backoff interval is set to the value of vRtrLdpAdjInitBackoff. After waiting for the backoff interval, LDP retries to setup the LDP session. If it fails again the backoff interval increases exponentially and this repeats for each successive LDP session startup failure. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, LDP will not backoff anymore and will give up trying to establish the LDP session.
T/F vRtrLdpAdjBackoffStatus	1.3.6.1.4.1.6527.3.1.2.8.15.1.5	TruthValue	read-only	The value of vRtrLdpAdjBackoffStatus indicates whether or not the entity is in backoff state. If this value is 'true', then the entity is in a backoff state and if the value is 'false' then the entity is not in a backoff state
vRtrLdpAdjBackoffTable	1.3.6.1.4.1.6527.3.1.2.8.15		not-accessible	vRtrLdpAdjBackoffTable is a read-only table which augments the vRtrLdpHelloAdjTable. The purpose of this table is to keep backoff information about the LDP Hello Adjacencies on the virtual router. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpHelloAdjTable, and the augmenting table vRtrLdpAdjBackoffTable. This in effect extends the vRtrLdpHelloAdjTable with additional columns. Creation or deletion of a row in the vRtrLdpHelloAdjTable results in the same fate for the row in the vRtrLdpAdjBackoffTable.
U32 vRtrLdpAdjCurrentBackoff	1.3.6.1.4.1.6527.3.1.2.8.15.1.3	Unsigned32	read-only	This value of vRtrLdpAdjCurrentBackoff specifies the current value of the backoff interval.
U32 vRtrLdpAdjInitBackoff	1.3.6.1.4.1.6527.3.1.2.8.15.1.1	Unsigned32	read-only	The value of vRtrLdpAdjInitBackoff specifies the initial backoff time. After a LDP session setup has failed, the value of vRtrLdpAdjInitBackoff is the time interval, in seconds, that the LDP entity waits before attempting to setup the session again. This interval is the backoff interval. This variable indicates the initial value for backoff interval when the LDP session startup first fails. Thereafter, if session startup fails again the backoff interval increases exponentially.
U32 vRtrLdpAdjMaxBackoff	1.3.6.1.4.1.6527.3.1.2.8.15.1.2	Unsigned32	read-only	The value of vRtrLdpAdjMaxBackoff specifies the maximum backoff time. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, the router will not backoff anymore and will give up trying to establish the LDP session. A value of 0 for vRtrLdpAdjMaxBackoff indicates that the backoff interval remains constant and will not increase exponentially. In effect the router will try to establish an LDP session till it succeeds
U32 vRtrLdpAdjWaitingTime	1.3.6.1.4.1.6527.3.1.2.8.15.1.4	Unsigned32	read-only	The value of vRtrLdpAdjWaitingTime specifies the time for which the entity has been waiting in backoff state.
vRtrLdpCepTdmFecEntry	1.3.6.1.4.1.6527.3.1.2.8.22.1		not-accessible	Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vRtrLdpCepTdmFecTable. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VRtrLdpCepTdmFecEntry.
vRtrLdpCepTdmFecTable	1.3.6.1.4.1.6527.3.1.2.8.22		not-accessible	vRtrLdpCepTdmFecTable is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options.
U32 vRtrLdpCepTdmLocalBitrate	1.3.6.1.4.1.6527.3.1.2.8.22.1.6	Unsigned32	read-only	The value of vRtrLdpCepTdmLocalBitrate indicates the local bitrate.
TDM vRtrLdpCepTdmLocalCasTrunk	1.3.6.1.4.1.6527.3.1.2.8.22.1.14	TdmOptionsCasTrunkFraming	read-only	The value of vRtrLdpCepTdmLocalCasTrunk indicates the local CE application signalling packets mode.
T/F vRtrLdpCepTdmLocalDiffTimestamp	1.3.6.1.4.1.6527.3.1.2.8.22.1.10	TruthValue	read-only	The value of vRtrLdpCepTdmLocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit.
U32 vRtrLdpCepTdmLocalPayloadSize	1.3.6.1.4.1.6527.3.1.2.8.22.1.4	Unsigned32	read-only	The value of vRtrLdpCepTdmLocalPayloadSize indicates the local payload size.
U32 vRtrLdpCepTdmLocalPayloadType	1.3.6.1.4.1.6527.3.1.2.8.22.1.18	Unsigned32	read-only	The value of vRtrLdpCepTdmLocalPayloadType indicates the local payload type.
T/F vRtrLdpCepTdmLocalRtpHeader	1.3.6.1.4.1.6527.3.1.2.8.22.1.8	TruthValue	read-only	The value of vRtrLdpCepTdmLocalRtpHeader indicates the local RTP header usage bit.
TDM vRtrLdpCepTdmLocalSigPkts	1.3.6.1.4.1.6527.3.1.2.8.22.1.12	TdmOptionsSigPkts	read-only	The value of vRtrLdpCepTdmLocalSigPkts indicates the local CE application signalling packets mode.
U32 vRtrLdpCepTdmLocalSsrcId	1.3.6.1.4.1.6527.3.1.2.8.22.1.20	Unsigned32	read-only	The value of vRtrLdpCepTdmLocalSsrcId indicates the local value of SSRC ID.
U32 vRtrLdpCepTdmLocalTimestampFreq	1.3.6.1.4.1.6527.3.1.2.8.22.1.16	Unsigned32	read-only	The value of vRtrLdpCepTdmLocalTimestampFreq indicates the local CE application signalling packets mode.
U32 vRtrLdpCepTdmRemoteBitrate	1.3.6.1.4.1.6527.3.1.2.8.22.1.7	Unsigned32	read-only	The value of vRtrLdpCepTdmRemoteBitrate indicates the remote bitrate.
TDM vRtrLdpCepTdmRemoteCasTrunk	1.3.6.1.4.1.6527.3.1.2.8.22.1.15	TdmOptionsCasTrunkFraming	read-only	The value of vRtrLdpCepTdmRemoteCasTrunk indicates the remote CE application signalling packets mode.
T/F vRtrLdpCepTdmRemoteDiffTimestamp	1.3.6.1.4.1.6527.3.1.2.8.22.1.11	TruthValue	read-only	The value of vRtrLdpCepTdmRemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit.
U32 vRtrLdpCepTdmRemotePayloadSize	1.3.6.1.4.1.6527.3.1.2.8.22.1.5	Unsigned32	read-only	The value of vRtrLdpCepTdmRemotePayloadSize indicates the remote payload size.
U32 vRtrLdpCepTdmRemotePayloadType	1.3.6.1.4.1.6527.3.1.2.8.22.1.19	Unsigned32	read-only	The value of vRtrLdpCepTdmRemotePayloadType indicates the remote payload type.
T/F vRtrLdpCepTdmRemoteRtpHeader	1.3.6.1.4.1.6527.3.1.2.8.22.1.9	TruthValue	read-only	The value of vRtrLdpCepTdmRemoteRtpHeader indicates the remote RTP header usage bit.
TDM vRtrLdpCepTdmRemoteSigPkts	1.3.6.1.4.1.6527.3.1.2.8.22.1.13	TdmOptionsSigPkts	read-only	The value of vRtrLdpCepTdmRemoteSigPkts indicates the remote CE application signalling packets mode.
U32 vRtrLdpCepTdmRemoteSsrcId	1.3.6.1.4.1.6527.3.1.2.8.22.1.21	Unsigned32	read-only	The value of vRtrLdpCepTdmRemoteSsrcId indicates the remote value of SSRC ID.
U32 vRtrLdpCepTdmRemoteTimestampFreq	1.3.6.1.4.1.6527.3.1.2.8.22.1.17	Unsigned32	read-only	The value of vRtrLdpCepTdmRemoteTimestampFreq indicates the remote CE application signalling packets mode.
TMN vRtrLdpGenAdminState	1.3.6.1.4.1.6527.3.1.2.8.1.1.2	TmnxAdminState	read-create	The value of vRtrLdpGenAdminState specifies the desired administrative state for this LDP instance.
TMN vRtrLdpGenBackoffTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.20	TmnxLdpBackoffTime	read-create	The value of vRtrLdpGenBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpGenBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially.
INT vRtrLdpGenControlMode	1.3.6.1.4.1.6527.3.1.2.8.1.1.12	INTEGER	read-only	The value of vRtrLdpGenControlMode specifies the mode used for distributing labels in response to label binding requests. When vRtrLdpGenControlMode has a value of 'ordered', label bindings are not distributed in response to a label request until a label binding has been received from the next hop for the destination. When vRtrLdpGenControlMode has a value of 'independent', label bindings are distributed immediately in response to a label request even if a label binding has not yet been received from the next hop for the destination.
TIM vRtrLdpGenCreateTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.28	TimeStamp	read-only	The value of vRtrLdpGenCreateTime specifies the sysUpTime when this LDP instance was created.
T/F vRtrLdpGenDeaggregateFec	1.3.6.1.4.1.6527.3.1.2.8.1.1.6	TruthValue	read-create	When vRtrLdpGenDeaggregateFec has a value of 'false', LDP aggregates multiple prefixes into a single Forwarding Equivalence Class (FEC) and advertises a single label for the FEC. When the value is 'true', LDP deaggregates prefixes into multiple FECs. This value is only applicable to LDP interfaces and not for targeted sessions.
TMN vRtrLdpGenDistMethod	1.3.6.1.4.1.6527.3.1.2.8.1.1.13	TmnxLdpLabelDistMethod	read-only	The value of vRtrLdpGenDistMethod specifies the label distribution method used. When vRtrLdpGenDistMethod has a value of 'downstreamOnDemand', label bindings are distributed to the upstream LSR, for each FEC, without requiring a request message for the FEC from the upstream LSR. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', label bindings are distributed to the upstream LSR only when a label request message is received.
vRtrLdpGeneralEntry	1.3.6.1.4.1.6527.3.1.2.8.1.1		not-accessible	Each row entry represents an instance of the Label Distribution Protocol (LDP) for a virtual router in the system. An entry in this table is created by the agent when vRtrLdpStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrLdpStatus is set to 'delete' but only if vRtrLdpGenAdminState has a value of 'outOfService'.
vRtrLdpGeneralTable	1.3.6.1.4.1.6527.3.1.2.8.1		not-accessible	vRtrLdpGeneralTable has an entry for each virtual router in the system capable of supporting an instance of the Label Distribution Protocol (LDP).
TPO vRtrLdpGenExportPolicy1	1.3.6.1.4.1.6527.3.1.2.8.1.1.35	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenExportPolicy1 specifies the first export policy used to filter LDP label bindings advertised to LDP peers.
TPO vRtrLdpGenExportPolicy2	1.3.6.1.4.1.6527.3.1.2.8.1.1.36	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenExportPolicy2 specifies the second export policy used to filter LDP label bindings advertised to LDP peers.
TPO vRtrLdpGenExportPolicy3	1.3.6.1.4.1.6527.3.1.2.8.1.1.37	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenExportPolicy3 specifies the third export policy used to filter LDP label bindings advertised to LDP peers.
TPO vRtrLdpGenExportPolicy4	1.3.6.1.4.1.6527.3.1.2.8.1.1.38	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenExportPolicy4 specifies the fourth export policy used to filter LDP label bindings advertised to LDP peers.
TPO vRtrLdpGenExportPolicy5	1.3.6.1.4.1.6527.3.1.2.8.1.1.39	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenExportPolicy5 specifies the fifth export policy used to filter LDP label bindings advertised to LDP peers.
T/F vRtrLdpGenGracefulRestart	1.3.6.1.4.1.6527.3.1.2.8.1.1.43	TruthValue	read-create	The value of vRtrLdpGenGracefulRestart specifies whether graceful restart helper is allowed. When this object has a value of 'true', graceful restart helper is enabled. When its value is 'false', graceful restart helper is disabled.
U32 vRtrLdpGenGRMaxRecoveryTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.45	Unsigned32	read-create	The value of vRtrLdpGenGRMaxRecoveryTime specifies the local maximum recovery time. If the Label Switching Router (LSR) determines that the neighbor was able to preserve its MPLS forwarding state (as was indicated by the non-zero Recovery Time advertised by the neighbor), the LSR should further keep the stale label-FEC bindings, received from the neighbor, for as long as the lesser of the Recovery Time advertised by the neighbor, and a local configurable value, called Maximum Recovery Time, allows. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'.
U32 vRtrLdpGenGRNbrLiveTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.44	Unsigned32	read-create	The value of vRtrLdpGenGRNbrLiveTime specifies the value for neighbor liveness timer. The amount of time the Label Switching Router (LSR) keeps its stale label-FEC bindings is set to the lesser of the FT Reconnect Timeout, as was advertised by the neighbor, and this local timer, called the Neighbor Liveness Timer. The LSR waits for the specified time till a LDP session re-establishes itself. If within that time the LSR still does not establish an LDP session with the neighbor, all the stale bindings are deleted. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'.
TMN vRtrLdpGenHelloFactor	1.3.6.1.4.1.6527.3.1.2.8.1.1.9	TmnxLdpHelloFactor	read-create	The value of vRtrLdpGenHelloFactor specifies the value by which the hello timeout (vRtrLdpGenHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
TMN vRtrLdpGenHelloTimeout	1.3.6.1.4.1.6527.3.1.2.8.1.1.10	TmnxLdpHelloTimeout	read-create	The value of vRtrLdpGenHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to LDP interfaces and not for targeted sessions.
U32 vRtrLdpGenHopLimit	1.3.6.1.4.1.6527.3.1.2.8.1.1.18	Unsigned32	read-create	The value of vRtrLdpGenHopLimit specifies the maximum allowable value for the hop count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'hopCount' or 'hopCountAndPathVector'.
TPO vRtrLdpGenImportPolicy1	1.3.6.1.4.1.6527.3.1.2.8.1.1.30	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenImportPolicy1 specifies the first import policy used to filter LDP label bindings received from LDP peers.
TPO vRtrLdpGenImportPolicy2	1.3.6.1.4.1.6527.3.1.2.8.1.1.31	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenImportPolicy2 specifies the second import policy used to filter LDP label bindings received from LDP peers.
TPO vRtrLdpGenImportPolicy3	1.3.6.1.4.1.6527.3.1.2.8.1.1.32	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenImportPolicy3 specifies the third import policy used to filter LDP label bindings received from LDP peers.
TPO vRtrLdpGenImportPolicy4	1.3.6.1.4.1.6527.3.1.2.8.1.1.33	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenImportPolicy4 specifies the fourth import policy used to filter LDP label bindings received from LDP peers.
TPO vRtrLdpGenImportPolicy5	1.3.6.1.4.1.6527.3.1.2.8.1.1.34	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpGenImportPolicy5 specifies the fifth import policy used to filter LDP label bindings received from LDP peers.
TMN vRtrLdpGenKeepAliveFactor	1.3.6.1.4.1.6527.3.1.2.8.1.1.7	TmnxLdpKeepAliveFactor	read-create	The value of vRtrLdpGenKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
TMN vRtrLdpGenKeepAliveTimeout	1.3.6.1.4.1.6527.3.1.2.8.1.1.8	TmnxLdpKeepAliveTimeout	read-create	The value of vRtrLdpGenKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpGenKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to LDP interfaces and not for targeted sessions.
TIM vRtrLdpGenLastChange	1.3.6.1.4.1.6527.3.1.2.8.1.1.1	TimeStamp	read-only	The value of vRtrLdpGenLastChange specifies the sysUpTime when this row was last modified.
OID vRtrLdpGenLdpLsrId	1.3.6.1.4.1.6527.3.1.2.8.1.1.4	MplsLsrIdentifier	read-only	The value of vRtrLdpGenLdpLsrId is the Label Switch Router (LSR) identifier which is used as the first 4 bytes or the Router Id component of the Label Distribution Protocol (LDP) identifier.
INT vRtrLdpGenLoopDetectCapable	1.3.6.1.4.1.6527.3.1.2.8.1.1.17	INTEGER	read-create	The value of vRtrLdpGenLoopDetectCapable indicate whether this LSR supports loop detection and if so, what type of loop detection is supported. When the value is 'none' loop detection is not supported on this LSR. When the value is 'other' Loop Detection is supported but by a method other than those listed below. When the value is 'hopCount' Loop Detection is supported by Hop Count only. When the value is 'pathVector' Loop Detection is supported by Path Vector only. When the value is 'hopCountAndPathVector' Loop Detection is supported by both Hop Count and Path Vector. Since Loop Detection is determined during Session Initialization, an individual session may not be running with loop detection. This object simply gives an indication of whether or not the LSR has the ability to support Loop Detection and which types.
TMN vRtrLdpGenMaxBackoffTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.21	TmnxLdpBackoffTime	read-create	The value of vRtrLdpGenMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpGenMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpGenMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.
TMN vRtrLdpGenOperDownReason	1.3.6.1.4.1.6527.3.1.2.8.1.1.41	TmnxLdpGenOperDownReasonCode	read-only	The value of vRtrLdpGenOperDownReason specifies the reason that the LDP instance is operationally down.
TMN vRtrLdpGenOperState	1.3.6.1.4.1.6527.3.1.2.8.1.1.3	TmnxOperState	read-only	The value of vRtrLdpGenOperState specifies the current operational state of this LDP instance.
U32 vRtrLdpGenPathVectorLimit	1.3.6.1.4.1.6527.3.1.2.8.1.1.19	Unsigned32	read-create	The value of vRtrLdpGenPathVectorLimit specifies the maximum allowable value for the path vector count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'pathVector' or 'hopCountAndPathVector'.
TMN vRtrLdpGenPropagatePolicy	1.3.6.1.4.1.6527.3.1.2.8.1.1.16	TmnxLdpFECPolicy	read-create	The value of vRtrLdpGenPropagatePolicy determines whether the LSR should generate FECs and which FECs it should generate. When the value of this object is 'system', LDP will distribute label bindings only for the router's system IP address When the value of this object is 'interface', LDP will distribute label bindings for all LDP interfaces When the value of this object is 'all', LDP will distribute label bindings for all prefixes in the routing table When the value of this object is 'none', LDP will not distribute any label bindings. This value is only applicable to LDP interfaces and not for targeted sessions.
U32 vRtrLdpGenProtocolVersion	1.3.6.1.4.1.6527.3.1.2.8.1.1.5	Unsigned32	read-only	The value of vRtrLdpGenProtocolVersion specifies the version of the LDP protocol instance. A value of zero (0) indicates that the version of the protocol is unknown.
INT vRtrLdpGenRetentionMode	1.3.6.1.4.1.6527.3.1.2.8.1.1.14	INTEGER	read-only	The value of vRtrLdpGenRetentionMode specifies the label retention mode used. If the value of this object is 'conservative', then advertized label mappings are retained only if they will be used to forward packets, i.e. if the label came from a valid next hop. Label bindings received from non-nexthops for each FEC are discarded. If the value of this object is 'liberal', then all advertized label mappings are retained whether they are from a valid next hop or not. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', a LSR may receive label bindings for the same destination for all its neighbors. Labels for the non-nexthops for the FECs are retained in the software but not used. When a network topology change occurs where a non-nexthop becomes a true next hop, the label received earlier is then used.
U32 vRtrLdpGenRoutePreference	1.3.6.1.4.1.6527.3.1.2.8.1.1.11	Unsigned32	read-create	The value of vRtrLdpGenRoutePreference specifies the route preference assigned to LDP routes. When multiple routes are available to a destination, the route with the lowest preference will be used. This value is only applicable to LDP interfaces and not for targeted sessions.
T/F vRtrLdpGenTargetedSessions	1.3.6.1.4.1.6527.3.1.2.8.1.1.27	TruthValue	read-create	The value of vRtrLdpGenTargetedSessions specifies whether or not targeted sessions are allowed. Targeted sessions are LDP sessions between indirectly connected peers. The discovery messages for an indirect LDP session are addressed to the specified peer instead of to the multicast address. When this object has a value of 'true', targeted sessions are enabled. When its value is 'false', targeted sessions are disabled.
TMN vRtrLdpGenTargHelloFactor	1.3.6.1.4.1.6527.3.1.2.8.1.1.24	TmnxLdpHelloFactor	read-create	The value of vRtrLdpGenTargHelloFactor specifies the value by which the hello timeout (vRtrLdpGenTargHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to targeted sessions and not to LDP interfaces.
TMN vRtrLdpGenTargHelloTimeout	1.3.6.1.4.1.6527.3.1.2.8.1.1.25	TmnxLdpHelloTimeout	read-create	The value of vRtrLdpGenTargHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to targeted sessions and not to LDP interfaces.
TMN vRtrLdpGenTargKeepAliveFactor	1.3.6.1.4.1.6527.3.1.2.8.1.1.22	TmnxLdpKeepAliveFactor	read-create	The value of vRtrLdpGenTargKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenTargKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to targeted sessions and not to LDP interfaces.
TMN vRtrLdpGenTargKeepAliveTimeout	1.3.6.1.4.1.6527.3.1.2.8.1.1.23	TmnxLdpKeepAliveTimeout	read-create	The value of vRtrLdpGenTargKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Genly the value of vRtrLdpGenTargKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to targeted sessions and not to LDP interfaces.
T/F vRtrLdpGenTargPassiveMode	1.3.6.1.4.1.6527.3.1.2.8.1.1.26	TruthValue	read-create	The value of vRtrLdpGenTargPassiveMode specifies the mode used for setting up LDP sessions. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers. This value is only applicable to targeted sessions and not to LDP interfaces.
INT vRtrLdpGenTransportAddrType	1.3.6.1.4.1.6527.3.1.2.8.1.1.15	INTEGER	read-create	The value of vRtrLdpGenTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. The transport address can be configured globally (applied to all interfaces) or per interface. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
TFI vRtrLdpGenTrustList	1.3.6.1.4.1.6527.3.1.2.8.1.1.42	TFilterID	read-create	The value of vRtrLdpGenTrustList specifies the IP filter ID used to verify trusted T-LDP peers. The IP filter specified by this object should contain a list of src-ip matches. The value '0' is not a valid IP filter ID, but it is used to indicate that there is no trust list. This object was obsoleted in release 5.0.
U32 vRtrLdpGenTunnelDownDampTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.40	Unsigned32	read-create	The value of vRtrLdpGenTunnelDownDampTime specifies the time interval, in seconds, that LDP waits before posting a tunnel down event to the Route Table Manager. If a tunnel up event is generated before the damping interval has elapsed, a tunnel modify event will be posted to the Route Table Manager (RTM). If this value is set to 0, then tunnel down events are not damped.
NUM vRtrLdpGenUpTime	1.3.6.1.4.1.6527.3.1.2.8.1.1.29	TimeInterval	read-only	The value of vRtrLdpGenUpTime specifies the time, in hundreds of seconds, that the LDP instance has been operationally up.
NTF vRtrLdpGroupIdMismatch	1.3.6.1.4.1.6527.3.1.3.8.0.5			The vRtrLdpGroupIdMismatch notification is generated when there is a mismatch of local and remote group IDs.
U32 vRtrLdpHelloAdjEntityIndex	1.3.6.1.4.1.6527.3.1.2.8.7.1.3	Unsigned32	read-only	The value of vRtrLdpHelloAdjEntityIndex specifies the Entity index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB.
vRtrLdpHelloAdjEntry	1.3.6.1.4.1.6527.3.1.2.8.7.1		not-accessible	Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
U32 vRtrLdpHelloAdjHoldTimeRemaining	1.3.6.1.4.1.6527.3.1.2.8.7.1.5	Unsigned32	read-only	The value of vRtrLdpHelloAdjHoldTimeRemaining specifies the hold time remaining for this Hello Adjacency. This interval will change when the next Hello message which corresponds to this Hello Adjacency is received.
U32 vRtrLdpHelloAdjIndex	1.3.6.1.4.1.6527.3.1.2.8.7.1.4	Unsigned32	read-only	The value of vRtrLdpHelloAdjIndex gives the Hello adjacency index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB.
C32 vRtrLdpHelloAdjInHelloMsgCount	1.3.6.1.4.1.6527.3.1.2.8.7.1.12	Counter32	read-only	The value of vRtrLdpHelloAdjInHelloMsgCount specifies the number of Hello messages that have been received for this adjacency.
U32 vRtrLdpHelloAdjLocalConfSeqNum	1.3.6.1.4.1.6527.3.1.2.8.7.1.10	Unsigned32	read-only	The value of vRtrLdpHelloAdjLocalConfSeqNum specifies the Configuration sequence number that was used in the Hello sent when this adjacency started up. This configuration sequence number changes when there is a change of configuration.
TMN vRtrLdpHelloAdjLocalHelloTimeout	1.3.6.1.4.1.6527.3.1.2.8.7.1.14	TmnxLdpHelloTimeout	read-only	The value of vRtrLdpHelloAdjLocalHelloTimeout specifies the hello timeout used in the Hellos sent for this specific adjacency.
IP vRtrLdpHelloAdjLocalIpAddress	1.3.6.1.4.1.6527.3.1.2.8.7.1.11	IpAddress	read-only	The value of vRtrLdpHelloAdjLocalIpAddress specifies the local IP address of the interface/targeted session used in Hellos sent for this specific adjacency.
OID vRtrLdpHelloAdjLocalLdpId	1.3.6.1.4.1.6527.3.1.2.8.7.1.2	MplsLdpIdentifier	read-only	The value of vRtrLdpHelloAdjLocalLdpId specifies the local LDP identifier for this specific adjacency.
vRtrLdpHelloAdjMapEntry	1.3.6.1.4.1.6527.3.1.2.8.8.1		not-accessible	Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
OID vRtrLdpHelloAdjMapLdpId	1.3.6.1.4.1.6527.3.1.2.8.8.1.1	MplsLdpIdentifier	read-only	vRtrLdpHelloAdjMapLdpId is an index for the row entry. It specifies the LDP identifier of the peer.
vRtrLdpHelloAdjMapTable	1.3.6.1.4.1.6527.3.1.2.8.8		not-accessible	vRtrLdpHelloAdjMapTable is a read-only table which maps to the vRtrLdpHelloAdjTable. This table has the same indexes as the vRtrLdpHelloAdjTable but the order in which these indexes are specified is different for the two tables.
C32 vRtrLdpHelloAdjOutHelloMsgCount	1.3.6.1.4.1.6527.3.1.2.8.7.1.13	Counter32	read-only	The value of vRtrLdpHelloAdjOutHelloMsgCount specifies the number of Hello messages that have been sent for this adjacency.
U32 vRtrLdpHelloAdjRemoteConfSeqNum	1.3.6.1.4.1.6527.3.1.2.8.7.1.7	Unsigned32	read-only	The value of vRtrLdpHelloAdjRemoteConfSeqNum specifies the Configuration sequence number that was in the Hello received when this adjacency started up. This configuration sequence number changes when there is a change of configuration.
TMN vRtrLdpHelloAdjRemoteHelloTimeout	1.3.6.1.4.1.6527.3.1.2.8.7.1.15	TmnxLdpHelloTimeout	read-only	The value of vRtrLdpHelloAdjRemoteHelloTimeout specifies the hello timeout used by the remote end that sent Hellos for this specific adjacency.
IP vRtrLdpHelloAdjRemoteIpAddress	1.3.6.1.4.1.6527.3.1.2.8.7.1.8	IpAddress	read-only	The value of vRtrLdpHelloAdjRemoteIpAddress specifies the peer IP address of the interface/targeted session that sent hellos for this specific adjacency.
vRtrLdpHelloAdjTable	1.3.6.1.4.1.6527.3.1.2.8.7		not-accessible	vRtrLdpHelloAdjTable is a read-only table. The purpose of this table is to keep information about Hello Adjacencies for Sessions. A hello adjacency can be associated with an LDP interface or with a targeted peer. The index includes both the interface index and the peer IP address thus referring to the LDP interface or targeted peer.
TMN vRtrLdpHelloAdjType	1.3.6.1.4.1.6527.3.1.2.8.7.1.6	TmnxLdpAdjacencyType	read-only	The value of vRtrLdpHelloAdjType specifies the type of this Hello Adjacency. If this value is 'link' then this adjacency is a result of a Link Hello. If this value is 'hello', then the adjacency is a result of a Targeted Hello.
NUM vRtrLdpHelloAdjUpTime	1.3.6.1.4.1.6527.3.1.2.8.7.1.9	TimeInterval	read-only	The value of vRtrLdpHelloAdjUpTime specifies the time, in hundreds of seconds, that this adjacency has been up.
TMN vRtrLdpIfAdminState	1.3.6.1.4.1.6527.3.1.2.8.5.1.5	TmnxAdminState	read-create	The value of vRtrLdpIfAdminState indicates the desired administrative state for LDP on this interface or targeted peer.
T/F vRtrLdpIfAutoCreate	1.3.6.1.4.1.6527.3.1.2.8.5.1.16	TruthValue	read-only	The value of vRtrLdpIfAutoCreate specifies whether or not the row entry represents a targeted peer that was automatically created through Service Manager. For an LDP interface, this value is always false.
TMN vRtrLdpIfBackoffTime	1.3.6.1.4.1.6527.3.1.2.8.5.1.12	TmnxLdpBackoffTime	read-create	The value of vRtrLdpIfBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpIfBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially.
vRtrLdpIfEntry	1.3.6.1.4.1.6527.3.1.2.8.5.1		not-accessible	Each row entry represents an interface on this virtual router that participates in the LDP protocol. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpIfRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'. An attempt to destroy a row will fail if vRtrLdpIfAdminState is not set to 'outOfService'.
G32 vRtrLdpIfExistingAdjacencies	1.3.6.1.4.1.6527.3.1.2.8.6.1.1	Gauge32	read-only	The value of vRtrLdpIfExistingAdjacencies gives a count of the total active adjacencies on this LDP interface or with this targeted peer.
TMN vRtrLdpIfHelloFactor	1.3.6.1.4.1.6527.3.1.2.8.5.1.10	TmnxLdpHelloFactor	read-create	The value of vRtrLdpIfHelloFactor specifies the value by which the hello timeout (vRtrLdpIfHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors.
TMN vRtrLdpIfHelloTimeout	1.3.6.1.4.1.6527.3.1.2.8.5.1.11	TmnxLdpHelloTimeout	read-create	The value of vRtrLdpIfHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time.
NUM vRtrLdpIfIndex	1.3.6.1.4.1.6527.3.1.2.8.5.1.1	InterfaceIndexOrZero	not-accessible	vRtrLdpIfIndex is an index for the row entry and is used mutually exclusively with the vRtrLdpPeerAddress field. If the vRtrLdpPeerAddress field is 0.0.0.0, then vRtrLdpIfIndex is the index for the interface on the virtual router and must be non-zero. Otherwise, vRtrLdpPeerAddress refers to a targeted peer and its vRtrLdpIfIndex is 0.
U32 vRtrLdpIfInheritance	1.3.6.1.4.1.6527.3.1.2.8.5.1.7	Unsigned32	read-create	Some writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrLdpGeneralTable for LDP interfaces or from the corresponding object in the vRtrLdpIfTable for targeted peers. vRtrLdpIfInheritance controls whether to inherit the operational value of that object, or use the administratively set value. This object is a bit-mask, with the following positions: vRtrLdpIfKeepAliveFactor 0x1 vRtrLdpIfKeepAliveTimeout 0x2 vRtrLdpIfHelloFactor 0x4 vRtrLdpIfHelloTimeout 0x8 vRtrLdpIfBackoffTime 0x10 vRtrLdpIfMaxBackoffTime 0x20 vRtrLdpIfTransportAddrType 0x40 vRtrLdpIfPassiveMode 0x80 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrLdpGeneralTable for LDP interfaces or the vRtrLdpIfTable for targeted peers.
TMN vRtrLdpIfKeepAliveFactor	1.3.6.1.4.1.6527.3.1.2.8.5.1.8	TmnxLdpKeepAliveFactor	read-create	The value of vRtrLdpIfKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpIfKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors.
TMN vRtrLdpIfKeepAliveTimeout	1.3.6.1.4.1.6527.3.1.2.8.5.1.9	TmnxLdpKeepAliveTimeout	read-create	The value of vRtrLdpIfKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpIfKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages).
TIM vRtrLdpIfLastChange	1.3.6.1.4.1.6527.3.1.2.8.5.1.4	TimeStamp	read-only	The value of vRtrLdpIfLastChange specifies the sysUpTime when this row was last modified.
TMN vRtrLdpIfLspId	1.3.6.1.4.1.6527.3.1.2.8.21.1.1	TmnxVRtrMplsLspID	not-accessible	The value of vRtrLdpIfLspId specifies the LSP id of the LSP associated with the specified interface or targeted peer.
ROW vRtrLdpIfLspRowStatus	1.3.6.1.4.1.6527.3.1.2.8.21.1.2	RowStatus	read-create	vRtrLdpIfLspRowStatus is used to create, delete or control entries in the vRtrLdpIfTunnelingLspTable. An entry is created by setting vRtrLdpIfLspRowStatus to 'createAndGo'. An entry is deleted by setting vRtrLdpIfLspRowStatus to 'destroy'.
TMN vRtrLdpIfMaxBackoffTime	1.3.6.1.4.1.6527.3.1.2.8.5.1.13	TmnxLdpBackoffTime	read-create	The value of vRtrLdpIfMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpIfMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpIfMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.
INT vRtrLdpIfNotifyReasonCode	1.3.6.1.4.1.6527.3.1.2.8.17.2	INTEGER	accessible-for-notify	Used by vRtrLdpIfStateChange, the value indicates the reason for the LSP interface state change.
NUM vRtrLdpIfOperDownReason	1.3.6.1.4.1.6527.3.1.2.8.5.1.17	TmnxLdpIntTargOperDownReasonCode	read-only	The value of vRtrLdpIfOperDownReason specifies the reason that the LDP interface or targeted peer is operationally down.
TMN vRtrLdpIfOperState	1.3.6.1.4.1.6527.3.1.2.8.5.1.6	TmnxOperState	read-only	The value of vRtrLdpIfOperState specifies the current operational state of LDP on this interface or targeted peer.
T/F vRtrLdpIfPassiveMode	1.3.6.1.4.1.6527.3.1.2.8.5.1.15	TruthValue	read-create	The value of vRtrLdpIfPassiveMode specifies the mode used for setting up LDP sessions. This object is meaningful only in case of LDP targeted peers and not for interfaces. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers.
ROW vRtrLdpIfRowStatus	1.3.6.1.4.1.6527.3.1.2.8.5.1.3	RowStatus	read-create	vRtrLdpIfRowStatus is used to control the creation and deletion of rows in the vRtrLdpIfTable. A row can be created by setting vRtrLdpIfRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'. An attempt to destroy a row will fail if vRtrLdpIfAdminState is not set to 'outOfService'.
NTF vRtrLdpIfStateChange	1.3.6.1.4.1.6527.3.1.3.8.0.3			The vRtrLdpIfStateChange notification is generated when the LDP interface changes state either administratively or operationally.
vRtrLdpIfStatsEntry	1.3.6.1.4.1.6527.3.1.2.8.6.1		not-accessible	A row in this table contains statistical information about an LDP Interface or Targeted peer. Some counters contained in a row are for fatal errors received during a former LDP Session associated with this entry. For example, an LDP Pdu received on a TCP connection during an LDP Session contains a fatal error. That error is counted here, because the session is terminated. If the error is NOT fatal (i.e. and the Session remains), then the error is counted in the vRtrLdpSessionStatsEntry.
vRtrLdpIfStatsTable	1.3.6.1.4.1.6527.3.1.2.8.6		not-accessible	vRtrLdpIfStatsTable is a read-only table. The purpose of this table is to keep statistical information about the LDP Interfaces and Targeted peers on the LSR. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpIfTable, and the augmenting table, vRtrLdpIfStatsTable. This in effect extends the vRtrLdpIfTable with additional columns. Creation or deletion of a row in the vRtrLdpIfTable results in the same fate for the row in the vRtrLdpIfStatsTable.
vRtrLdpIfTable	1.3.6.1.4.1.6527.3.1.2.8.5		not-accessible	vRtrLdpIfTable provides an entry for each virtual router interface or targeted peer configured to be used with the Label Distribution Protocol (LDP).
TES vRtrLdpIfTableSpinlock	1.3.6.1.4.1.6527.3.1.2.8.4	TestAndIncr	read-write	Voluntary serialization control for vRtrLdpIfTable. Primarily used by SNMP manager to coordinate changes to vRtrLdpIfInheritance.
INT vRtrLdpIfTransportAddrType	1.3.6.1.4.1.6527.3.1.2.8.5.1.14	INTEGER	read-create	The value of vRtrLdpIfTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. This value is meaningful only in case of LDP interfaces and not for targeted peers. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors.
T/F vRtrLdpIfTunneling	1.3.6.1.4.1.6527.3.1.2.8.5.1.18	TruthValue	read-create	The value of vRtrLdpIfTunneling specifies whether tunneling of LDP over tunnels is enabled. When this object has a value of 'true', tunneling is enabled. When its value is 'false', tunneling is disabled.
vRtrLdpIfTunnelingLspEntry	1.3.6.1.4.1.6527.3.1.2.8.21.1		not-accessible	A row in this table contains the LSP id information about an LDP interface or targeted peer. Row entries can be created or deleted via SNMP SET requests. A row is created by setting vRtrLdpIfLspRowStatus to 'createAndGo' provided the corresponding LSP id exists as an MPLS lsp. A row entry can be destroyed by setting vRtrLdpIfLspRowStatus to 'destroy'.
vRtrLdpIfTunnelingLspTable	1.3.6.1.4.1.6527.3.1.2.8.21		not-accessible	vRtrLdpIfTunnelingLspTable keeps the list of LDP-over-RSVP LSP ids which are currently supported by the application. Each LSP ID in the list corresponds to the vRtrMplsLspIndex of the given MPLS LSP.
INT vRtrLdpInstanceNotifyReasonCode	1.3.6.1.4.1.6527.3.1.2.8.17.1	INTEGER	accessible-for-notify	Used by vRtrLdpInstanceStateChange, the value indicates the reason for the LDP instance state change.
NTF vRtrLdpInstanceStateChange	1.3.6.1.4.1.6527.3.1.3.8.0.2			The vRtrLdpInstanceStateChange notification is generated when the LDP module changes state either administratively or operationally.
TMN vRtrLdpNotifyLocalGroupID	1.3.6.1.4.1.6527.3.1.2.8.17.5	TmnxVcId	accessible-for-notify	Used by vRtrLdpGroupIdMismatch, the value indicates the local Group ID.
TMN vRtrLdpNotifyLocalServiceID	1.3.6.1.4.1.6527.3.1.2.8.17.3	TmnxServId	accessible-for-notify	Used by vRtrLdpSvcIdMismatch, the value indicates the local Service ID.
TMN vRtrLdpNotifyRemoteGroupID	1.3.6.1.4.1.6527.3.1.2.8.17.6	TmnxVcId	accessible-for-notify	Used by vRtrLdpGroupIdMismatch, the value indicates the remote Group ID.
TMN vRtrLdpNotifyRemoteServiceID	1.3.6.1.4.1.6527.3.1.2.8.17.4	TmnxServId	accessible-for-notify	Used by vRtrLdpSvcIdMismatch, the value indicates the remote Service ID.
IP vRtrLdpPeerAddress	1.3.6.1.4.1.6527.3.1.2.8.5.1.2	IpAddress	not-accessible	vRtrLdpPeerAddress is an index for the row entry and is used mutually exclusively with the vRtrLdpIfIndex field. If the vRtrLdpIfIndex field is 0, then the vRtrLdpPeerAddress is the IP address of the targeted peer and must be non-zero. Otherwise, vRtrLdpIfIndex refers to the LDP interface index and its vRtrLdpPeerAddress is 0.0.0.0
T/F vRtrLdpPeerAuth	1.3.6.1.4.1.6527.3.1.2.8.16.1.2	TruthValue	read-create	When the value of vRtrLdpPeerAuth is 'true', authentication using MD5 message based digest protocol is enabled. When 'false', no authentication is used.
OCT vRtrLdpPeerAuthKey	1.3.6.1.4.1.6527.3.1.2.8.16.1.3	OCTET STRING	read-create	The string specified in vRtrLdpPeerAuthKey is the authentication key to be used between LDP neighbors before establishing sessions. Authentication is done using the MD-5 message based digest protocol. The authentication key can be any combination of letters or numbers. Note that the string may contain embedded nulls. An SNMP Get request on this object should return an OCTET STRING of length 0.
TNA vRtrLdpPeerAuthKeyChain	1.3.6.1.4.1.6527.3.1.2.8.16.1.6	TNamedItemOrEmpty	read-create	The value of vRtrLdpPeerAuthKeyChain specifies the keychain which will be used to sign and/or authenticate the BGP protocol stream. The keychain name is defined by tmnxKeyChainName and is the index for TIMETRA-SECURITY-MIB::tmnxKeyChainTable
OID vRtrLdpPeerLdpId	1.3.6.1.4.1.6527.3.1.2.8.7.1.1	MplsLdpIdentifier	not-accessible	vRtrLdpPeerLdpId is an index for the row entry. It specifies the LDP identifier of the peer.
U32 vRtrLdpPeerMinTTLValue	1.3.6.1.4.1.6527.3.1.2.8.16.1.4	Unsigned32	read-create	The value of vRtrLdpPeerMinTTLValue specifies the minimum TTL value for an incoming LDP packet. If vRtrLdpPeerMinTTLValue is set to zero (0), the TTL Security feature is disabled.
vRtrLdpPeerParamsEntry	1.3.6.1.4.1.6527.3.1.2.8.16.1		not-accessible	Each row entry represents a peer that participates in the LDP protocol on this virtual router. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpPeerRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'. A row entry with vRtrLdpPeerAddress of 0.0.0.0 represents the default LDP parameters used for all peers that do not have a corresponding entry in this table.
vRtrLdpPeerParamsTable	1.3.6.1.4.1.6527.3.1.2.8.16		not-accessible	vRtrLdpPeerParamsTable has an entry for an LDP peer. This table is used to configure parmaters specific to the peer whether it is an interface or a targeted peer.
ROW vRtrLdpPeerRowStatus	1.3.6.1.4.1.6527.3.1.2.8.16.1.1	RowStatus	read-create	vRtrLdpPeerRowStatus is used to control the creation and deletion of rows in the vRtrLdpPeerParamsTable. A row can be created by setting vRtrLdpPeerRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'.
TFI vRtrLdpPeerTTLLogId	1.3.6.1.4.1.6527.3.1.2.8.16.1.5	TFilterLogId	read-create	The value of vRtrLdpPeerTTLLogId specifies the filter log to use for packets that fail TTL security check. The value zero indicates that logging is disabled.
vRtrLdpPolicyEntry	1.3.6.1.4.1.6527.3.1.2.8.3.1		not-accessible	Each row entry represents a policy used by the LDP protocol instance. Entries can be created and deleted via SNMP SET operations to vRtrLdpPolicyRowStatus. This entry is obsoleted in release 2.1.
U32 vRtrLdpPolicyIndex	1.3.6.1.4.1.6527.3.1.2.8.3.1.2	Unsigned32	not-accessible	vRtrLdpPolicyIndex is used to control the order that the LDP policies are applied. If multiple entries exist in this table with the same vRtrID and vRtrLdpPolicyType indexes, they are evaluated in ascending numeric order of vRtrLdpPolicyIndex (gaps are allowed). The first policy that matches is applied. This object is obsoleted in release 2.1.
TPO vRtrLdpPolicyName	1.3.6.1.4.1.6527.3.1.2.8.3.1.4	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpPolicyName is the name of the policy filter to be used. If this object has the value of the empty string, ''H, there is no policy specified at this level. This object is obsoleted in release 2.1.
ROW vRtrLdpPolicyRowStatus	1.3.6.1.4.1.6527.3.1.2.8.3.1.3	RowStatus	read-create	vRtrLdpPolicyRowStatus controls the creation and deletion of rows in the vRtrLdpPolicyTable. This object is obsoleted in release 2.1.
vRtrLdpPolicyTable	1.3.6.1.4.1.6527.3.1.2.8.3		not-accessible	vRtrLdpPolicyTable has an entry for each policy used by the LDP protocol instance running on the virtual router. This table is obsoleted in release 2.1.
INT vRtrLdpPolicyType	1.3.6.1.4.1.6527.3.1.2.8.3.1.1	INTEGER	not-accessible	The value of vRtrLdpPolicyType indicates the type of policy specified in this row entry. When vRtrLdpPolicyType has a value of 'import' this row entry represents the policy filter to be applied to the label binding received from a neighbor. When the value is 'export', this row entry represents the policy filter to determine the labels to be advertised to the neighbors. When the value is 'ingress', this row entry represents the policy filter to control the route prefixes that are advertised by LDP to the route table. LDP will advertise label bindings of prefixes that are advertised into it. When the value is 'egress', this row entry represents the policy filter to control the route prefixes that are advertised into LDP from the route table. LDP will advertise label bindings of prefixes that are advertised into it. This object is obsoleted in release 2.1.
vRtrLdpServFecEntry	1.3.6.1.4.1.6527.3.1.2.8.11.1		not-accessible	Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
TMN vRtrLdpServFecFecType	1.3.6.1.4.1.6527.3.1.2.8.11.1.1	TmnxLdpFECType	not-accessible	The value of vRtrLdpServFecFecType specifies the FEC type.
TMN vRtrLdpServFecFlags	1.3.6.1.4.1.6527.3.1.2.8.11.1.7	TmnxLdpFECFlags	read-only	The bit flags of vRtrLdpServFecFlags specify the characteristics of the FEC.
U32 vRtrLdpServFecInLabel1	1.3.6.1.4.1.6527.3.1.2.8.11.1.10	Unsigned32	read-only	The value of vRtrLdpServFecInLabel1 specifies the first ingress label exchanged
U32 vRtrLdpServFecInLabel2	1.3.6.1.4.1.6527.3.1.2.8.11.1.12	Unsigned32	read-only	The value of vRtrLdpServFecInLabel2 specifies the second ingress label (if at all) exchanged.
U32 vRtrLdpServFecInLabel3	1.3.6.1.4.1.6527.3.1.2.8.11.1.14	Unsigned32	read-only	The value of vRtrLdpServFecInLabel3 specifies the third ingress label (if at all) exchanged.
U32 vRtrLdpServFecInLabel4	1.3.6.1.4.1.6527.3.1.2.8.11.1.16	Unsigned32	read-only	The value of vRtrLdpServFecInLabel4 specifies the fourth ingress label (if at all) exchanged.
U32 vRtrLdpServFecInLabel5	1.3.6.1.4.1.6527.3.1.2.8.11.1.18	Unsigned32	read-only	The value of vRtrLdpServFecInLabel5 specifies the fifth ingress label (if at all) exchanged.
TMN vRtrLdpServFecInLabelSigStatus1	1.3.6.1.4.1.6527.3.1.2.8.11.1.37	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecInLabelSigStatus1 indicates the signaling status for vRtrLdpServFecInLabel1.
TMN vRtrLdpServFecInLabelSigStatus2	1.3.6.1.4.1.6527.3.1.2.8.11.1.38	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecInLabelSigStatus2 indicates the signaling status for vRtrLdpServFecInLabel2.
TMN vRtrLdpServFecInLabelSigStatus3	1.3.6.1.4.1.6527.3.1.2.8.11.1.39	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecInLabelSigStatus3 indicates the signaling status for vRtrLdpServFecInLabel3.
TMN vRtrLdpServFecInLabelSigStatus4	1.3.6.1.4.1.6527.3.1.2.8.11.1.40	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecInLabelSigStatus4 indicates the signaling status for vRtrLdpServFecInLabel4.
TMN vRtrLdpServFecInLabelSigStatus5	1.3.6.1.4.1.6527.3.1.2.8.11.1.41	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecInLabelSigStatus5 indicates the signaling status for vRtrLdpServFecInLabel5.
TMN vRtrLdpServFecInLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.11.1.11	TmnxLabelStatus	read-only	The value of vRtrLdpServFecInLabelStatus1 specifies the status of the ingress label 1
TMN vRtrLdpServFecInLabelStatus2	1.3.6.1.4.1.6527.3.1.2.8.11.1.13	TmnxLabelStatus	read-only	The value of vRtrLdpServFecInLabelStatus2 specifies the status of the ingress label 2
TMN vRtrLdpServFecInLabelStatus3	1.3.6.1.4.1.6527.3.1.2.8.11.1.15	TmnxLabelStatus	read-only	The value of vRtrLdpServFecInLabelStatus3 specifies the status of the ingress label 3
TMN vRtrLdpServFecInLabelStatus4	1.3.6.1.4.1.6527.3.1.2.8.11.1.17	TmnxLabelStatus	read-only	The value of vRtrLdpServFecInLabelStatus4 specifies the status of the ingress label 4
TMN vRtrLdpServFecInLabelStatus5	1.3.6.1.4.1.6527.3.1.2.8.11.1.19	TmnxLabelStatus	read-only	The value of vRtrLdpServFecInLabelStatus5 specifies the status of the ingress label 5
U32 vRtrLdpServFecLocalMaxCellConcat	1.3.6.1.4.1.6527.3.1.2.8.11.1.35	Unsigned32	read-only	The value of vRtrLdpServFecLocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
U32 vRtrLdpServFecLocalMTU	1.3.6.1.4.1.6527.3.1.2.8.11.1.31	Unsigned32	read-only	The value of vRtrLdpServFecLocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR.
U32 vRtrLdpServFecLocalVlanTag	1.3.6.1.4.1.6527.3.1.2.8.11.1.33	Unsigned32	read-only	The value of vRtrLdpServFecLocalVlanTag specifies the local tag on a VLAN VC type SDP binding.
vRtrLdpServFecMapEntry	1.3.6.1.4.1.6527.3.1.2.8.12.1		not-accessible	Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
TMN vRtrLdpServFecMapFecType	1.3.6.1.4.1.6527.3.1.2.8.12.1.1	TmnxLdpFECType	read-only	The value of vRtrLdpServFecMapFecType specifies the FEC type.
vRtrLdpServFecMapTable	1.3.6.1.4.1.6527.3.1.2.8.12		not-accessible	vRtrLdpServFecMapTable is a read-only table which maps to the vRtrLdpServFecTable. This table has the same indexes as the vRtrLdpServFecTable but the order in which these indexes are specified is different for the two tables.
TMN vRtrLdpServFecMapVcId	1.3.6.1.4.1.6527.3.1.2.8.12.1.3	TmnxVcId	read-only	The value of vRtrLdpServFecMapVcId specifies the VC identifier associated with this service FEC.
TMN vRtrLdpServFecMapVcType	1.3.6.1.4.1.6527.3.1.2.8.12.1.2	TmnxVcType	read-only	The value of vRtrLdpServFecMapVcType specifies the VC type associated with this service FEC.
SDP vRtrLdpServFecMateEndpointSdpId	1.3.6.1.4.1.6527.3.1.2.8.11.1.48	SdpId	read-only	The value of vRtrLdpServFecMateEndpointSdpId identifies the SDP associated with this service FEC mate endpoint for vc-switching.
TMN vRtrLdpServFecMateEndpointVcId	1.3.6.1.4.1.6527.3.1.2.8.11.1.47	TmnxVcId	read-only	The value of vRtrLdpServFecMateEndpointVcId specifies the VC identifier associated with this service FEC mate endpoint for vc-switching.
U32 vRtrLdpServFecNumInLabels	1.3.6.1.4.1.6527.3.1.2.8.11.1.8	Unsigned32	read-only	The value of vRtrLdpServFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecInLabel1 thru vRtrLdpServFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumInLabels is 3 then vRtrLdpServFecInLabel1, vRtrLdpServFecInLabel2 and vRtrLdpServFecInLabel3 will contain valid label information.
U32 vRtrLdpServFecNumOutLabels	1.3.6.1.4.1.6527.3.1.2.8.11.1.9	Unsigned32	read-only	The value of vRtrLdpServFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecOutLabel1 thru vRtrLdpServFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumOutLabels is 3, then vRtrLdpServFecOutLabel1, vRtrLdpServFecOutLabel2 and vRtrLdpServFecOutLabel3 will contain valid label information.
U32 vRtrLdpServFecOutLabel1	1.3.6.1.4.1.6527.3.1.2.8.11.1.20	Unsigned32	read-only	The value of vRtrLdpServFecOutLabel1 specifies the first egress label exchanged.
U32 vRtrLdpServFecOutLabel2	1.3.6.1.4.1.6527.3.1.2.8.11.1.22	Unsigned32	read-only	The value of vRtrLdpServFecOutLabel2 specifies the second egress label (if at all) exchanged.
U32 vRtrLdpServFecOutLabel3	1.3.6.1.4.1.6527.3.1.2.8.11.1.24	Unsigned32	read-only	The value of vRtrLdpServFecOutLabel3 specifies the third egress label (if at all) exchanged.
U32 vRtrLdpServFecOutLabel4	1.3.6.1.4.1.6527.3.1.2.8.11.1.26	Unsigned32	read-only	The value of vRtrLdpServFecOutLabel4 specifies the fourth egress label (if at all) exchanged.
U32 vRtrLdpServFecOutLabel5	1.3.6.1.4.1.6527.3.1.2.8.11.1.28	Unsigned32	read-only	The value of vRtrLdpServFecOutLabel5 specifies the fifth egress label (if at all) exchanged.
TMN vRtrLdpServFecOutLabelSigStatus1	1.3.6.1.4.1.6527.3.1.2.8.11.1.42	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecOutLabelSigStatus1 indicates the signaling status for vRtrLdpServFecOutLabel1.
TMN vRtrLdpServFecOutLabelSigStatus2	1.3.6.1.4.1.6527.3.1.2.8.11.1.43	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecOutLabelSigStatus2 indicates the signaling status for vRtrLdpServFecOutLabel2.
TMN vRtrLdpServFecOutLabelSigStatus3	1.3.6.1.4.1.6527.3.1.2.8.11.1.44	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecOutLabelSigStatus3 indicates the signaling status for vRtrLdpServFecOutLabel3.
TMN vRtrLdpServFecOutLabelSigStatus4	1.3.6.1.4.1.6527.3.1.2.8.11.1.45	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecOutLabelSigStatus4 indicates the signaling status for vRtrLdpServFecOutLabel4.
TMN vRtrLdpServFecOutLabelSigStatus5	1.3.6.1.4.1.6527.3.1.2.8.11.1.46	TmnxLabelSigStatus	read-only	The value of vRtrLdpServFecOutLabelSigStatus5 indicates the signaling status for vRtrLdpServFecOutLabel5.
TMN vRtrLdpServFecOutLabelStatus1	1.3.6.1.4.1.6527.3.1.2.8.11.1.21	TmnxLabelStatus	read-only	The value of vRtrLdpServFecOutLabelStatus1 specifies the status of the egress label 1
TMN vRtrLdpServFecOutLabelStatus2	1.3.6.1.4.1.6527.3.1.2.8.11.1.23	TmnxLabelStatus	read-only	The value of vRtrLdpServFecOutLabelStatus2 specifies the status of the egress label 2
TMN vRtrLdpServFecOutLabelStatus3	1.3.6.1.4.1.6527.3.1.2.8.11.1.25	TmnxLabelStatus	read-only	The value of vRtrLdpServFecOutLabelStatus3 specifies the status of the egress label 3
TMN vRtrLdpServFecOutLabelStatus4	1.3.6.1.4.1.6527.3.1.2.8.11.1.27	TmnxLabelStatus	read-only	The value of vRtrLdpServFecOutLabelStatus4 specifies the status of the egress label 4
TMN vRtrLdpServFecOutLabelStatus5	1.3.6.1.4.1.6527.3.1.2.8.11.1.29	TmnxLabelStatus	read-only	The value of vRtrLdpServFecOutLabelStatus5 specifies the status of the egress label 5
U32 vRtrLdpServFecRemoteMaxCellConcat	1.3.6.1.4.1.6527.3.1.2.8.11.1.36	Unsigned32	read-only	The value of vRtrLdpServFecRemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
U32 vRtrLdpServFecRemoteMTU	1.3.6.1.4.1.6527.3.1.2.8.11.1.32	Unsigned32	read-only	The value of vRtrLdpServFecRemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR.
U32 vRtrLdpServFecRemoteVlanTag	1.3.6.1.4.1.6527.3.1.2.8.11.1.34	Unsigned32	read-only	The value of vRtrLdpServFecRemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding.
SDP vRtrLdpServFecSdpId	1.3.6.1.4.1.6527.3.1.2.8.11.1.30	SdpId	read-only	The value of vRtrLdpServFecSdpId identifies the SDP associated with this peer.
TMN vRtrLdpServFecServId	1.3.6.1.4.1.6527.3.1.2.8.11.1.5	TmnxServId	read-only	The value of vRtrLdpServFecServId specifies the Service identifier associated with this service FEC.
SER vRtrLdpServFecServType	1.3.6.1.4.1.6527.3.1.2.8.11.1.4	ServType	read-only	The value of vRtrLdpServFecServType specifies the Service type associated with this service FEC.
vRtrLdpServFecTable	1.3.6.1.4.1.6527.3.1.2.8.11		not-accessible	vRtrLdpServFecTable is a read-only table that represents all service FECs either sent to or received from an LDP peer known to the Virtual Router.
TMN vRtrLdpServFecVcId	1.3.6.1.4.1.6527.3.1.2.8.11.1.3	TmnxVcId	not-accessible	The value of vRtrLdpServFecVcId specifies the VC identifier associated with this service FEC.
TMN vRtrLdpServFecVcType	1.3.6.1.4.1.6527.3.1.2.8.11.1.2	TmnxVcType	not-accessible	The value of vRtrLdpServFecVcType specifies the VC type associated with this service FEC.
TMN vRtrLdpServFecVpnId	1.3.6.1.4.1.6527.3.1.2.8.11.1.6	TmnxVpnId	read-only	The value of vRtrLdpServFecVpnId identifies the VPN associated with the FEC.
TMN vRtrLdpSessAdjacencyType	1.3.6.1.4.1.6527.3.1.2.8.9.1.7	TmnxLdpAdjacencyType	read-only	The value of vRtrLdpSessAdjacencyType specifies the adjacency type(s) supporting this LDP Session.
INT vRtrLdpSessAdvertise	1.3.6.1.4.1.6527.3.1.2.8.9.1.20	INTEGER	read-only	The value of vRtrLdpSessAdvertise indicates the type of FECs that will be transported by the session.
U32 vRtrLdpSessEntityIndex	1.3.6.1.4.1.6527.3.1.2.8.9.1.2	Unsigned32	read-only	The value of vRtrLdpSessEntityIndex specifies the Entity index for the LDP entity represented in this session.
U32 vRtrLdpSessFtReconnectTimeNego	1.3.6.1.4.1.6527.3.1.2.8.9.1.24	Unsigned32	read-only	The value of vRtrLdpSessFtReconnectTimeNego indicates the session's Fault Tolerant(FT) Reconnect Timeout, it is set to the lesser of the neighbor advertised FT Reconnect Timeout, vRtrLdpSessFtReconTimeRemaining and the local timer Neighbor Liveness Time, vRtrLdpGenGRNbrLiveTime. It is within this period that the transport session is expected to re-establish, failure to do so will cause the teardown of the LDP session and deletion of stale bindings.
U32 vRtrLdpSessFtReconTimeRemaining	1.3.6.1.4.1.6527.3.1.2.8.9.1.26	Unsigned32	read-only	The value of vRtrLdpSessFtReconTimeRemaining indicates the amount of time left before the session's Fault Tolerant(FT) reconnect timeout,vRtrLdpSessFtReconnectTimeNego expires.
U32 vRtrLdpSessFtRecoveryTimeNego	1.3.6.1.4.1.6527.3.1.2.8.9.1.25	Unsigned32	read-only	The value of vRtrLdpSessFtRecoveryTimeNego indicates the session's Fault Tolerant(FT) recovery timeout, it is set to the lesser of the neighbor advertised FT recovery timeout, vRtrLdpSessFtRecovTimeRemaining and the local timer maximum recovery time, vRtrLdpGenGRMaxRecoveryTime. It is within this period that label-FEC binding message exchanges are expected to complete. Any stale FEC entries left after this time will be deleted from the FEC table.
U32 vRtrLdpSessFtRecovTimeRemaining	1.3.6.1.4.1.6527.3.1.2.8.9.1.27	Unsigned32	read-only	This value indicates the amount of time left before session's Fault Tolerant(FT) recovery timeout, vRtrLdpSessFtRecoveryTimeNego expires.
vRtrLdpSessionEntry	1.3.6.1.4.1.6527.3.1.2.8.9.1		not-accessible	A row in this table represents information about a single session between an LDP entity and an LDP Peer.
vRtrLdpSessionStatsEntry	1.3.6.1.4.1.6527.3.1.2.8.10.1		not-accessible	A row in this table represents statistical information about a single session between an LDP entity and an LDP Peer.
vRtrLdpSessionStatsTable	1.3.6.1.4.1.6527.3.1.2.8.10		not-accessible	vRtrLdpSessionStatsTable is a read-only table. The purpose of this table is to keep statistical information about a single session between an LDP entity and an LDP Peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpSessionTable, and the augmenting table, vRtrLdpSessionStatsTable. This in effect extends the vRtrLdpSessionTable with additional columns. Creation or deletion of a row in the vRtrLdpSessionTable results in the same fate for the row in the vRtrLdpSessionStatsTable.
vRtrLdpSessionTable	1.3.6.1.4.1.6527.3.1.2.8.9		not-accessible	vRtrLdpSessionTable is a read-only table which parallels the mplsLdpSessionTable in the MPLS-LDP-MIB. The purpose of this table is to keep information about a single session between an LDP entity and an LDP Peer.
NUM vRtrLdpSessKAHoldTimeRemaining	1.3.6.1.4.1.6527.3.1.2.8.9.1.15	TimeInterval	read-only	The value of vRtrLdpSessKAHoldTimeRemaining specifies the keep alive hold time remaining, in hundredths of seconds, for this LDP session.
TMN vRtrLdpSessLabelDistMethod	1.3.6.1.4.1.6527.3.1.2.8.9.1.3	TmnxLdpLabelDistMethod	read-only	The value of vRtrLdpSessLabelDistMethod specifies the label distribution method used for this LDP session.
TIM vRtrLdpSessLastRestartTime	1.3.6.1.4.1.6527.3.1.2.8.9.1.23	TimeStamp	read-only	The value of vRtrLdpSessLastRestartTime indicates the last time graceful restart helper was initiated.
IP vRtrLdpSessLocalAddress	1.3.6.1.4.1.6527.3.1.2.8.9.1.13	IpAddress	read-only	The value of vRtrLdpSessLocalAddress specifies the IP address used locally for the LDP Session.
TMN vRtrLdpSessLocalKATimeout	1.3.6.1.4.1.6527.3.1.2.8.9.1.18	TmnxLdpKeepAliveTimeout	read-only	The value of vRtrLdpSessLocalKATimeout specifies the keepalive timeout used locally for the LDP Session.
OID vRtrLdpSessLocalLdpId	1.3.6.1.4.1.6527.3.1.2.8.9.1.1	MplsLdpIdentifier	read-only	The value of vRtrLdpSessLocalLdpId specifies the local LDP identifier for this LDP session.
U32 vRtrLdpSessLocalTcpPort	1.3.6.1.4.1.6527.3.1.2.8.9.1.11	Unsigned32	read-only	The value of vRtrLdpSessLocalTcpPort specifies the TCP port used locally for the LDP Session.
U32 vRtrLdpSessLocalUdpPort	1.3.6.1.4.1.6527.3.1.2.8.9.1.9	Unsigned32	read-only	The value of vRtrLdpSessLocalUdpPort specifies the UDP port used locally for LDP discovery.
INT vRtrLdpSessLoopDetectForPV	1.3.6.1.4.1.6527.3.1.2.8.9.1.4	INTEGER	read-only	The value of vRtrLdpSessLoopDetectForPV indicates whether loop detection based on path vectors is disabled or enabled for this LDP session. If this object has a value of disabled(0), then loop detection is disabled. Otherwise, if this object has a value of enabled(1), then loop detection based on path vectors is enabled.
U32 vRtrLdpSessMaxPduLength	1.3.6.1.4.1.6527.3.1.2.8.9.1.16	Unsigned32	read-only	The value of vRtrLdpSessMaxPduLength specifies the maximum allowable length for LDP PDUs for this session. This value may have been negotiated during Session Initialization.
U32 vRtrLdpSessPathVectorLimit	1.3.6.1.4.1.6527.3.1.2.8.9.1.5	Unsigned32	read-only	If the value of vRtrLdpSessLoopDetectForPV for this entry is 'enabled', then the value of vRtrLdpSessPathVectorLimit represents the Path Vector Limit for this LDP Session. If the value of vRtrLdpSessLoopDetectForPV for this entry is 'disabled', then the value of vRtrLdpSessPathVectorLimit be 0 (zero).
IP vRtrLdpSessPeerAddress	1.3.6.1.4.1.6527.3.1.2.8.9.1.14	IpAddress	read-only	The value of vRtrLdpSessPeerAddress specifies the IP address used on the remote end for the LDP Session.
TMN vRtrLdpSessPeerKATimeout	1.3.6.1.4.1.6527.3.1.2.8.9.1.19	TmnxLdpKeepAliveTimeout	read-only	The value of vRtrLdpSessPeerKATimeout specifies the keepalive timeout used at the remote end of the LDP Session.
C32 vRtrLdpSessPeerNumRestart	1.3.6.1.4.1.6527.3.1.2.8.9.1.22	Counter32	read-only	The value of vRtrLdpSessPeerNumRestart indicates the number of times graceful restart helper was initiated for this session.
U32 vRtrLdpSessPeerTcpPort	1.3.6.1.4.1.6527.3.1.2.8.9.1.12	Unsigned32	read-only	The value of vRtrLdpSessPeerTcpPort specifies the TCP port used on the remote end for the LDP Session.
U32 vRtrLdpSessPeerUdpPort	1.3.6.1.4.1.6527.3.1.2.8.9.1.10	Unsigned32	read-only	The value of vRtrLdpSessPeerUdpPort specifies the UDP port used on the remote end for LDP discovery.
U32 vRtrLdpSessProtocolVersion	1.3.6.1.4.1.6527.3.1.2.8.9.1.8	Unsigned32	read-only	The value of vRtrLdpSessProtocolVersion specifies the version of the LDP Protocol used by this session.
T/F vRtrLdpSessRestartHelperState	1.3.6.1.4.1.6527.3.1.2.8.9.1.21	TruthValue	read-only	The value of vRtrLdpSessRestartHelperState indicates whether the entity session is capable of supporting graceful restart. This is negotiated between peers during the session initialization setup.
INT vRtrLdpSessState	1.3.6.1.4.1.6527.3.1.2.8.9.1.6	INTEGER	read-only	The value of vRtrLdpSessState specifies the current state of the LDP session. All of the states 1 - 5 are based on the state machine for session negotiation behavior.
C32 vRtrLdpSessStatsAddrIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.21	Counter32	read-only	The value of vRtrLdpSessStatsAddrIn counts the number of Address Messages that have been received during this session.
C32 vRtrLdpSessStatsAddrOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.22	Counter32	read-only	The value of vRtrLdpSessStatsAddrOut counts the number of Address Messages that have been sent during this session.
C32 vRtrLdpSessStatsAddrWithdrawIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.23	Counter32	read-only	The value of vRtrLdpSessStatsAddrWithdrawIn counts the number of Address Withdraw Messages that have been received during this session.
C32 vRtrLdpSessStatsAddrWithdrawOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.24	Counter32	read-only	The value of vRtrLdpSessStatsAddrWithdrawOut counts the number of Address Withdraw Messages that have been sent during this session.
C32 vRtrLdpSessStatsFECRecv	1.3.6.1.4.1.6527.3.1.2.8.10.1.3	Counter32	read-only	The value of vRtrLdpSessStatsFECRecv counts the number of FECs received for this session.
C32 vRtrLdpSessStatsFECSent	1.3.6.1.4.1.6527.3.1.2.8.10.1.4	Counter32	read-only	The value of vRtrLdpSessStatsFECSent counts the number of FECs sent for this session.
C32 vRtrLdpSessStatsHelloIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.5	Counter32	read-only	The value of vRtrLdpSessStatsHelloIn counts the number of Hello Messages that have been received during this session.
C32 vRtrLdpSessStatsHelloOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.6	Counter32	read-only	The value of vRtrLdpSessStatsHelloOut counts the number of Hello Messages that have been sent during this session.
C32 vRtrLdpSessStatsInitIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.9	Counter32	read-only	The value of vRtrLdpSessStatsInitIn counts the number of Init Messages that have been received during this session.
C32 vRtrLdpSessStatsInitOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.10	Counter32	read-only	The value of vRtrLdpSessStatsInitOut counts the number of Init Messages that have been sent during this session.
C32 vRtrLdpSessStatsKeepaliveIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.7	Counter32	read-only	The value of vRtrLdpSessStatsKeepaliveIn counts the number of Keepalive Messages that have been received during this session.
C32 vRtrLdpSessStatsKeepaliveOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.8	Counter32	read-only	The value of vRtrLdpSessStatsKeepaliveOut counts the number of Keepalive Messages that have been sent during this session.
C32 vRtrLdpSessStatsLabelAbortIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.19	Counter32	read-only	The value of vRtrLdpSessStatsLabelAbortIn counts the number of Label Abort Messages that have been received during this session.
C32 vRtrLdpSessStatsLabelAbortOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.20	Counter32	read-only	The value of vRtrLdpSessStatsLabelAbortOut counts the number of Label Abort Messages that have been sent during this session.
C32 vRtrLdpSessStatsLabelMappingIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.11	Counter32	read-only	The value of vRtrLdpSessStatsLabelMappingIn counts the number of Label Mapping Messages that have been received during this session.
C32 vRtrLdpSessStatsLabelMappingOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.12	Counter32	read-only	The value of vRtrLdpSessStatsLabelMappingOut counts the number of Label Mapping Messages that have been sent during this session.
C32 vRtrLdpSessStatsLabelReleaseIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.15	Counter32	read-only	The value of vRtrLdpSessStatsLabelReleaseIn counts the number of Label Release Messages that have been received during this session.
C32 vRtrLdpSessStatsLabelReleaseOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.16	Counter32	read-only	The value of vRtrLdpSessStatsLabelReleaseOut counts the number of Label Release Messages that have been sent during this session.
C32 vRtrLdpSessStatsLabelRequestIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.13	Counter32	read-only	The value of vRtrLdpSessStatsLabelRequestIn counts the number of Label Request Messages that have been received during this session.
C32 vRtrLdpSessStatsLabelRequestOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.14	Counter32	read-only	The value of vRtrLdpSessStatsLabelRequestOut counts the number of Label Request Messages that have been sent during this session.
C32 vRtrLdpSessStatsLabelWithdrawIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.17	Counter32	read-only	The value of vRtrLdpSessStatsLabelWithdrawIn counts the number of Label Withdraw Messages that have been received during this session.
C32 vRtrLdpSessStatsLabelWithdrawOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.18	Counter32	read-only	The value of vRtrLdpSessStatsLabelWithdrawOut counts the number of Label Withdraw Messages that have been sent during this session.
G32 vRtrLdpSessStatsLinkAdj	1.3.6.1.4.1.6527.3.1.2.8.10.1.2	Gauge32	read-only	The value of vRtrLdpSessStatsLinkAdj specifies the number of link adjacencies for this session.
C32 vRtrLdpSessStatsNotificationIn	1.3.6.1.4.1.6527.3.1.2.8.10.1.25	Counter32	read-only	The value of vRtrLdpSessStatsNotificationIn counts the number of Notification Messages that have been received during this session.
C32 vRtrLdpSessStatsNotificationOut	1.3.6.1.4.1.6527.3.1.2.8.10.1.26	Counter32	read-only	The value of vRtrLdpSessStatsNotificationOut counts the number of Notification Messages that have been sent during this session.
G32 vRtrLdpSessStatsTargAdj	1.3.6.1.4.1.6527.3.1.2.8.10.1.1	Gauge32	read-only	The value of vRtrLdpSessStatsTargAdj specifies the number of targeted adjacencies for this session.
NUM vRtrLdpSessUpTime	1.3.6.1.4.1.6527.3.1.2.8.9.1.17	TimeInterval	read-only	The value of vRtrLdpSessUpTime specifies the time, in hundreds of seconds, since the session was established.
NTF vRtrLdpStateChange	1.3.6.1.4.1.6527.3.1.3.8.0.1			The vRtrLdpStateChange notification is generated when the LDP protocol is created or deleted in the router.
vRtrLdpStaticFecEntry	1.3.6.1.4.1.6527.3.1.2.8.18.1		not-accessible	Each row entry represents a static prefix FEC configured on the virtual router. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecRowStatus. An entry is created by setting vRtrLdpStaticFecRowStatus to 'createAndWait'. The row status can be set to 'active' only after a next-hop entry corresponding to this prefix has been created in the vRtrLdpStaticFecNHTable. An entry is deleted by setting vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, there must be no next-hop entries corresponding to this prefix in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0.
U32 vRtrLdpStaticFecIngLabel	1.3.6.1.4.1.6527.3.1.2.8.18.1.5	Unsigned32	read-create	The value of vRtrLdpStaticFecIngLabel specifies the label that is advertised to the upstream peer. If this variable is set to the default value of 4294967295, the ingress label will be dynamically assigned by the label manager.
IP vRtrLdpStaticFecIpMask	1.3.6.1.4.1.6527.3.1.2.8.18.1.2	IpAddress	not-accessible	The value of vRtrLdpStaticFecIpMask specifies the IP Address Mask for this static FEC.
IP vRtrLdpStaticFecIpPrefix	1.3.6.1.4.1.6527.3.1.2.8.18.1.1	IpAddress	not-accessible	The value of vRtrLdpStaticFecIpPrefix specifies the IP Address Prefix for this static FEC.
U32 vRtrLdpStaticFecNextNHIndex	1.3.6.1.4.1.6527.3.1.2.8.18.1.4	Unsigned32	read-only	The value of vRtrLdpStaticFecNextNHIndex is used to assign values to vRtrLdpStaticFecNHIndex when creating rows in the vRtrLdpStaticFecNHTable. The network manager reads this object and uses it in the SET request that creates a new row entry in the vRtrLdpStaticFecNHTable. If the SET fails with the code 'inconsistentValue', the process must be repeated. If the SET succeeds, then this object will be incremented and the new instance is created according to the manager's directions.
U32 vRtrLdpStaticFecNHEgrLabel	1.3.6.1.4.1.6527.3.1.2.8.19.1.5	Unsigned32	read-create	The value of vRtrLdpStaticFecNHEgrLabel specifies the egress label associated with this next-hop entry. The LSR will swap the incoming label with the configured egress label. If this egress label has a value of 4294967295, the LSR will pop the incoming label.
vRtrLdpStaticFecNHEntry	1.3.6.1.4.1.6527.3.1.2.8.19.1		not-accessible	Each row entry represents a next-hop configured for a static prefix FEC on the virtual router. The static prefix FEC corresponding to a next-hop entry must exist as a row entry in the vRtrLdpStaticFecTable. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecNHRowStatus. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'.
U32 vRtrLdpStaticFecNHIndex	1.3.6.1.4.1.6527.3.1.2.8.19.1.1	Unsigned32	not-accessible	The value of vRtrLdpStaticFecNHIndex is used to identify the next-hop associated with a static prefix FEC. This value is unique amongst next-hop entries for the same static prefix FEC.
IP vRtrLdpStaticFecNHIpAddr	1.3.6.1.4.1.6527.3.1.2.8.19.1.4	IpAddress	read-create	If vRtrLdpStaticFecNHType is set to 'ipAddress', the value of vRtrLdpStaticFecNHIpAddr specifies the IP address of the next-hop. In this case, this variable must be set to a valid value before the row be placed in an active state. If vRtrLdpStaticFecNHType is set to 'pop', this value of vRtrLdpStaticFecNHIpAddr will be 0.0.0.0
ROW vRtrLdpStaticFecNHRowStatus	1.3.6.1.4.1.6527.3.1.2.8.19.1.2	RowStatus	read-create	vRtrLdpStaticFecNHRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecNHTable. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'.
vRtrLdpStaticFecNHTable	1.3.6.1.4.1.6527.3.1.2.8.19		not-accessible	vRtrLdpStaticFecNHTable has an entry for each next-hop configured for a static prefix FEC on the virtual router.
INT vRtrLdpStaticFecNHType	1.3.6.1.4.1.6527.3.1.2.8.19.1.3	INTEGER	read-create	The value of vRtrLdpStaticFecNHType specifies the type of next-hop represented by this row entry. unknown (0) - the next-hop type has not been set. ipAddress (1) - the next-hop is an IP address. pop (2) - there is no next-hop i.e. pop the label and route
G32 vRtrLdpStaticFecNumNH	1.3.6.1.4.1.6527.3.1.2.8.18.1.6	Gauge32	read-only	The value of vRtrLdpStaticFecNumNH specifies the number of next-hops that are associated with the static prefix FEC represented by this row entry. This is also the number of row entries configured in the vRtrLdpStaticFecNHTable for this static prefix FEC. If the static FEC has no next-hops associated with it, this value will be 0 and the row entry will be placed in the 'notReady' state. Deletion of the row entry will be allowed only if vRtrLdpStaticFecNumNH is 0.
U32 vRtrLdpStaticFecOperIngLabel	1.3.6.1.4.1.6527.3.1.2.8.18.1.7	Unsigned32	read-only	The value of vRtrLdpStaticFecOperIngLabel specifies the actual or operational value of the label that was advertised to the upstream peer.
ROW vRtrLdpStaticFecRowStatus	1.3.6.1.4.1.6527.3.1.2.8.18.1.3	RowStatus	read-create	vRtrLdpStaticFecRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecTable. To create a row entry, set vRtrLdpStaticFecRowStatus to 'createAndWait'. Before the row can be placed in the 'active' state, a next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable. To delete a row entry, set vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, no next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0.
vRtrLdpStaticFecTable	1.3.6.1.4.1.6527.3.1.2.8.18		not-accessible	vRtrLdpStaticFecTable has an entry for each static prefix FEC configured on the virtual router.
G32 vRtrLdpStatsActiveAdjacencies	1.3.6.1.4.1.6527.3.1.2.8.2.1.3	Gauge32	read-only	The value of vRtrLdpStatsActiveAdjacencies specifies the number of active adjacencies (i.e. established sessions) associated with the LDP instance.
G32 vRtrLdpStatsActiveInterfaces	1.3.6.1.4.1.6527.3.1.2.8.2.1.4	Gauge32	read-only	The value of vRtrLdpStatsActiveInterfaces specifies the number of active (i.e. operationally up) interfaces associated with the LDP instance.
G32 vRtrLdpStatsActiveSessions	1.3.6.1.4.1.6527.3.1.2.8.2.1.2	Gauge32	read-only	The value of vRtrLdpStatsActiveSessions specifies the number of active sessions (i.e. session in some form of creation) associated with the LDP instance.
G32 vRtrLdpStatsActiveTargSessions	1.3.6.1.4.1.6527.3.1.2.8.2.1.6	Gauge32	read-only	The value of vRtrLdpStatsActiveTargSessions specifies the number of active (i.e. operationally up) targeted sessions associated with the LDP instance.
G32 vRtrLdpStatsAddrFECRecv	1.3.6.1.4.1.6527.3.1.2.8.2.1.8	Gauge32	read-only	The value of vRtrLdpStatsAddrFECRecv specifies the number of Address FECs received by the LDP instance from its neighbors.
G32 vRtrLdpStatsAddrFECSent	1.3.6.1.4.1.6527.3.1.2.8.2.1.9	Gauge32	read-only	The value of vRtrLdpStatsAddrFECSent specifies the number of Address FECs sent by the LDP instance to its neighbors.
C32 vRtrLdpStatsAttemptedSessions	1.3.6.1.4.1.6527.3.1.2.8.2.1.12	Counter32	read-only	The value of vRtrLdpStatsAttemptedSessions specifies the total number of attempted sessions for this LDP instance.
C32 vRtrLdpStatsBadLdpIdentifierErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.17	Counter32	read-only	The value of vRtrLdpStatsBadLdpIdentifierErrors gives the number of Bad LDP Identifier Fatal Errors detected for sessions associated with this LDP instance.
C32 vRtrLdpStatsBadMessageLengthErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.19	Counter32	read-only	The value of vRtrLdpStatsBadMessageLengthErrors gives the number of Bad Message Length Fatal Errors detected for sessions associated with this LDP instance.
C32 vRtrLdpStatsBadPduLengthErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.18	Counter32	read-only	The value of vRtrLdpStatsBadPduLengthErrors gives the number of Bad Pdu Length Fatal Errors detected for sessions associated with this LDP instance.
C32 vRtrLdpStatsBadTlvLengthErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.20	Counter32	read-only	The value of vRtrLdpStatsBadTlvLengthErrors gives the number of Bad TLV Length Fatal Errors detected for sessions associated with this LDP instance.
vRtrLdpStatsEntry	1.3.6.1.4.1.6527.3.1.2.8.2.1		not-accessible	A row in this table represents statistical information about an LDP instance.
G32 vRtrLdpStatsInactiveInterfaces	1.3.6.1.4.1.6527.3.1.2.8.2.1.5	Gauge32	read-only	The value of vRtrLdpStatsInactiveInterfaces specifies the number of inactive (i.e. operationally down) interfaces associated with the LDP instance.
G32 vRtrLdpStatsInactiveTargSessions	1.3.6.1.4.1.6527.3.1.2.8.2.1.7	Gauge32	read-only	The value of vRtrLdpStatsInactiveTargSessions specifies the number of inactive (i.e. operationally down) targeted sessions associated with the LDP instance.
C32 vRtrLdpStatsKeepAliveExpiredErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.22	Counter32	read-only	The value of vRtrLdpStatsKeepAliveExpiredErrors gives the number of Session Keep Alive Timer Expired Errors detected for sessions associated with this LDP instance.
C32 vRtrLdpStatsMalformedTlvValueErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.21	Counter32	read-only	The value of vRtrLdpStatsMalformedTlvValueErrors gives the number of Malformed TLV Value Fatal Errors detected for sessions associated with this LDP instance.
C32 vRtrLdpStatsOperDownEventsEx	1.3.6.1.4.1.6527.3.1.2.8.2.1.1	Counter32	read-only	The value of vRtrLdpStatsOperDownEvents specifies the number of times the LDP instance has gone operationally down since the instance was created.
C32 vRtrLdpStatsSessRejAdvErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.14	Counter32	read-only	The value of vRtrLdpStatsSessRejAdvErrors gives the total number of Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP instance.
C32 vRtrLdpStatsSessRejLabelRangeErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.16	Counter32	read-only	The value of vRtrLdpStatsSessRejLabelRangeErrors gives the total number of Session Rejected/Parameters Label Range Error Notification Messages sent or received by this LDP instance.
C32 vRtrLdpStatsSessRejMaxPduErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.15	Counter32	read-only	The value of vRtrLdpStatsSessRejMaxPduErrors gives the total number of Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP instance.
C32 vRtrLdpStatsSessRejNoHelloErrors	1.3.6.1.4.1.6527.3.1.2.8.2.1.13	Counter32	read-only	The value of vRtrLdpStatsSessRejNoHelloErrors gives the total number of Session Rejected/No Hello Error Notification Messages sent or received by this LDP instance.
C32 vRtrLdpStatsShutdownNotifRecv	1.3.6.1.4.1.6527.3.1.2.8.2.1.23	Counter32	read-only	The value of vRtrLdpStatsShutdownNotifRecv gives the number of Shutdown Notifications received related to sessions associated with this LDP instance.
C32 vRtrLdpStatsShutdownNotifSent	1.3.6.1.4.1.6527.3.1.2.8.2.1.24	Counter32	read-only	The value of vRtrLdpStatsShutdownNotifSent gives the number of Shutdown Notifications sent related to sessions associated with this LDP instance.
G32 vRtrLdpStatsSvcFECRecv	1.3.6.1.4.1.6527.3.1.2.8.2.1.10	Gauge32	read-only	The value of vRtrLdpStatsSvcFECRecv specifies the number of Service FECs received by the LDP instance from its neighbors.
G32 vRtrLdpStatsSvcFECSent	1.3.6.1.4.1.6527.3.1.2.8.2.1.11	Gauge32	read-only	The value of vRtrLdpStatsSvcFECSent specifies the number of Service FECs sent by the LDP instance to its neighbors.
vRtrLdpStatsTable	1.3.6.1.4.1.6527.3.1.2.8.2		not-accessible	vRtrLdpStatsTable is a read-only table. The purpose of this table is to keep statistical information about an LDP Instance. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpStatsTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpStatsTable.
NTF vRtrLdpSvcIdMismatch	1.3.6.1.4.1.6527.3.1.3.8.0.4			The vRtrLdpSvcIdMismatch notification is generated when there is a mismatch of local and remote service IDs.
vRtrLdpTargEntry	1.3.6.1.4.1.6527.3.1.2.8.20.1		not-accessible	A row in this table represents information about the targeted LDP session.
TPO vRtrLdpTargExportPolicy1	1.3.6.1.4.1.6527.3.1.2.8.20.1.8	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargExportPolicy1 specifies the export route policy used to determine which routes are exported to this targeted LDP session. A maximum of 5 policies can be specified. vRtrLdpTargExportPolicy1 specifies the first policy.
TPO vRtrLdpTargExportPolicy2	1.3.6.1.4.1.6527.3.1.2.8.20.1.9	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargExportPolicy2 specifies the second export policy used to determine which routes are exported to this targeted LDP session
TPO vRtrLdpTargExportPolicy3	1.3.6.1.4.1.6527.3.1.2.8.20.1.10	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargExportPolicy3 specifies the third export policy used to determine which routes are exported to this targeted LDP session.
TPO vRtrLdpTargExportPolicy4	1.3.6.1.4.1.6527.3.1.2.8.20.1.11	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargExportPolicy4 specifies the fourth export policy used to determine which routes are exported to this targeted LDP session.
TPO vRtrLdpTargExportPolicy5	1.3.6.1.4.1.6527.3.1.2.8.20.1.12	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargExportPolicy5 specifies the fifth export policy used to determine which routes are exported to this targeted LDP session.
TPO vRtrLdpTargImportPolicy1	1.3.6.1.4.1.6527.3.1.2.8.20.1.3	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargImportPolicy1 specifies the import route policy to determine which routes are accepted from targeted LDP neighbors. A maximum of 5 policies can be specified. vRtrLdpTargImportPolicy1 specifies the first policy.
TPO vRtrLdpTargImportPolicy2	1.3.6.1.4.1.6527.3.1.2.8.20.1.4	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargImportPolicy2 specifies the second import policy used to determine which routes are accepted from targeted LDP neighbors.
TPO vRtrLdpTargImportPolicy3	1.3.6.1.4.1.6527.3.1.2.8.20.1.5	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargImportPolicy3 specifies the third import policy used to determine which routes are accepted from targeted LDP neighbors.
TPO vRtrLdpTargImportPolicy4	1.3.6.1.4.1.6527.3.1.2.8.20.1.6	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargImportPolicy4 specifies the fourth import policy to determine which routes are accepted from targeted LDP neighbors.
TPO vRtrLdpTargImportPolicy5	1.3.6.1.4.1.6527.3.1.2.8.20.1.7	TPolicyStatementNameOrEmpty	read-create	The value of vRtrLdpTargImportPolicy5 specifies the fifth import policy used to determine which routes are accepted from targeted LDP neighbors.
vRtrLdpTargTable	1.3.6.1.4.1.6527.3.1.2.8.20		not-accessible	vRtrLdpTargTable keeps information about the export and import prefixes for a targeted LDP session. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpTargTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpTargTable.
T/F vRtrLdpTargTunnelPreference	1.3.6.1.4.1.6527.3.1.2.8.20.1.13	TruthValue	read-create	The value of vRtrLdpTargTunnelPreference indicates whether LDP over tunnel is preferred when link-level LDP bindings are also available. If this value is 'true', then LDP tunnels are preferred and if the value is 'false' then LDP over tunnel is preferred. By default LDP tunnels are preferred.

RFC description

Alcatel 7x50 Label Distribution Protocol (LDP) configuration and management.

Start monitoring Nokia (Alcatel-Lucent) 7750 SR-series service routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-TIMETRA-LDP-MIB