ALCATEL-IND1-TIMETRA-MPLS-MIB

All MIBs › ALCATEL-IND1-TIMETRA-MPLS-MIB

Organization: Alcatel

Last Updated: 2008-01-01

Category: MPLS and Traffic Engineering, Vendor: Alcatel-Lucent

Description: Alcatel 7750 SR service router MPLS MIB for managing LSPs, RSVP-TE tunnels, and MPLS forwarding tables.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-TIMETRA-MPLS-MIB?

ALCATEL-IND1-TIMETRA-MPLS-MIB is Alcatel-Lucent's (Timetra) proprietary MIB for the 7x50 SR family of service routers, extending standard MPLS management with vendor-specific objects for label-switched paths (LSPs) and RSVP-TE tunnels. It exposes configuration data (LSP name, source/destination addresses, LSP type) alongside operational state objects describing the current health of each provisioned MPLS path. For monitoring purposes it is primarily a service/software-status MIB rather than a physical-hardware MIB: it lets an operator track whether an LSP's administrative and operational state are up or down, when the state last changed, and which outgoing segment carries the traffic, effectively surfacing MPLS forwarding-plane software status rather than chassis sensors. It builds on the general MPLS-LSR-MIB/MPLS-TE-MIB conventions from IETF, adapted into Alcatel's 'tmnx'/virtual-router object model. It is deployed in service-provider core and edge networks running 7750/7450 SR platforms to manage and troubleshoot MPLS-based VPN and traffic-engineering services, and engineers typically start with an ALCATEL-IND1-TIMETRA-MPLS-MIB download to load the module into their MIB browser for reference.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-TIMETRA-MPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel-Lucent (Nokia) 7750 SR service router
Alcatel-Lucent 7450 ESS

Monitoring Examples

An operator polls vRtrMplsLspTable / vRtrMplsLspEntry and watches vRtrMplsLspOperState versus vRtrMplsLspAdminState for a given vRtrMplsLspIndex to detect an LSP that is administratively enabled but operationally down. Correlating this with vRtrMplsLspLastChange pinpoints when the failure occurred, while vRtrMplsLspFromAddr and vRtrMplsLspToAddr identify the head-end and tail-end router addresses to narrow down which network segment is affected. vRtrMplsLspType and vRtrMplsLspOutSegIndx help distinguish a primary path failure from a standby/secondary path reroute.

What Can Be Monitored

LSP administrative state
LSP operational state
LSP last state-change time
LSP source/destination addresses
LSP type (primary/secondary)
outgoing segment index

Imported Objects

From ALCATEL-IND1-TIMETRA-GLOBAL-MIB

timetraSRMIBModules	OBJECT-IDENTITY
tmnxSRConfs	OBJECT-IDENTITY
tmnxSRNotifyPrefix	OBJECT-IDENTITY
tmnxSRObjs	OBJECT-IDENTITY

From ALCATEL-IND1-TIMETRA-TC-MIB

TNamedItem
TNamedItemOrEmpty
TmnxActionType
TmnxAdminState
TmnxOperState
TmnxVRtrMplsLspID

From ALCATEL-IND1-TIMETRA-VRTR-MIB

vRtrID	OBJECT-TYPE
vRtrIfIndex	OBJECT-TYPE

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddressIPv6

From MPLS-LSR-MIB

MplsLSPID
MplsLabel
mplsXCLspId	OBJECT-TYPE

From MPLS-TE-MIB

mplsTunnelARHopEntry	OBJECT-TYPE
mplsTunnelIndex	OBJECT-TYPE
mplsTunnelIngressLSRId	OBJECT-TYPE
mplsTunnelInstance	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowPointer
RowStatus
TEXTUAL-CONVENTION
TestAndIncr
TimeInterval
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using vRtrMplsLspOctets OID:

Select a Nokia (Alcatel-Lucent) 7750 SR-series service router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vRtrMplsLspOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of octets that have been forwarded over current LSP active path. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
timetraMplsMIBModule	1.3.6.1.4.1.6527.1.1.3.6			This document is the SNMP MIB module to manage and provision the MPLS extensions for the Alcatel 7x50 device. Copyright 2003-2008 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
tmnxMplsAdminGroupGroup	1.3.6.1.4.1.6527.3.1.1.6.2.8			The group of objects supporting management of extended MPLS administrative groups on Alcatel 7x50 SR series systems.
tmnxMplsCompliances	1.3.6.1.4.1.6527.3.1.1.6.1
tmnxMplsConformance	1.3.6.1.4.1.6527.3.1.1.6
tmnxMplsFSGroupGroup	1.3.6.1.4.1.6527.3.1.1.6.2.9			The group of objects supporting management of extended MPLS fate sharing groups on Alcatel 7x50 SR series systems.
tmnxMplsGlobalR2r1Group	1.3.6.1.4.1.6527.3.1.1.6.2.12			The group of objects supporting general management of extended MPLS on Alcatel 7x50 SR series systems 2.1 Release.
tmnxMplsGlobalV5v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.16			The group of objects supporting general management of extended MPLS on Alcatel 7x50 SR series systems 5.0 Release.
tmnxMplsGlobalV6v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.18			The group of objects supporting general management of extended MPLS on Alcatel 7x50 SR series systems 6.0 Release.
tmnxMplsGroups	1.3.6.1.4.1.6527.3.1.1.6.2
tmnxMplsIfGroup	1.3.6.1.4.1.6527.3.1.1.6.2.5			The group of objects supporting management of extended MPLS interfaces on Alcatel 7x50 SR series systems.
tmnxMplsIfV6v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.21			The group of objects supporting management of Te metric feature on extended MPLS interfaces on 6.0 release Alcatel 7xxx SR series systems.
tmnxMplsLabelRangeGroup	1.3.6.1.4.1.6527.3.1.1.6.2.15			The group of objects supporting management of extended MPLS label ranges on Alcatel 7x50 SR series systems.
tmnxMplsLspPathGroup	1.3.6.1.4.1.6527.3.1.1.6.2.3			The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel 7x50 SR series systems.
tmnxMplsLspR2r1Group	1.3.6.1.4.1.6527.3.1.1.6.2.13			The group of objects supporting management of extended MPLS LSPs on Alcatel 7x50 SR series systems 2.1 Release.
tmnxMplsLspV5v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.17			The group of objects supporting management of extended MPLS LSPs on Alcatel 7x50 SR series systems 5.0 Release.
tmnxMplsLspV6v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.22			The group of objects supporting management of Te metric feature extended MPLS LSPs on 6.0 release Alcatel 7xxx SR series systems.
tmnxMplsNotificationlObjects	1.3.6.1.4.1.6527.3.1.2.6.16
tmnxMplsNotificationR2r1Group	1.3.6.1.4.1.6527.3.1.1.6.2.14			The group of notifications supporting the extended MPLS feature on Alcatel 7x50 SR series systems 2.1 Release.
tmnxMplsNotifications	1.3.6.1.4.1.6527.3.1.3.6.0
tmnxMplsNotifyObjsGroup	1.3.6.1.4.1.6527.3.1.1.6.2.10			The group of objects supporting extended MPLS notifications on Alcatel 7x50 SR series systems.
tmnxMplsNotifyPrefix	1.3.6.1.4.1.6527.3.1.3.6
tmnxMplsObjs	1.3.6.1.4.1.6527.3.1.2.6
tmnxMplsSrlgV6v0Group	1.3.6.1.4.1.6527.3.1.1.6.2.19			The group of objects supporting management of SRLG on Alcatel 7xxx SR series systems release 6.0.
tmnxMplsTunnelARHopGroup	1.3.6.1.4.1.6527.3.1.1.6.2.6			The group of objects supporting management of extended MPLS Tunnel AR hops on Alcatel 7x50 SR series systems.
tmnxMplsTunnelCHopGroup	1.3.6.1.4.1.6527.3.1.1.6.2.7			The group of objects supporting management of extended MPLS CSPF Tunnel hops on Alcatel 7x50 SR series systems.
tmnxMplsV3v0Compliance	1.3.6.1.4.1.6527.3.1.1.6.1.3			The compliance statement for management of extended MPLS on Alcatel 7x50 SR series systems 3.0 Release.
tmnxMplsV5v0Compliance	1.3.6.1.4.1.6527.3.1.1.6.1.4			The compliance statement for management of extended MPLS on Alcatel 7xxx SR series systems 5.0 Release.
tmnxMplsV6v0Compliance	1.3.6.1.4.1.6527.3.1.1.6.1.5			The compliance statement for management of extended MPLS on Alcatel 7xxx SR series systems 6.0 Release.
tmnxMplsXCGroup	1.3.6.1.4.1.6527.3.1.1.6.2.4			The group of objects supporting management of extended MPLS LSP to cross-connection mapping on Alcatel 7x50 SR series systems.
vRtrMplsAdminGroupEntry	1.3.6.1.4.1.6527.3.1.2.6.13.1		not-accessible	Each row entry in the vRtrMplsAdminGroupTable represents an administrative group which is simply a mapping between a group name (an ASCII string) and a group value (a number in the range 0 to 31). Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsAdminGroupRowStatus to 'createAndWait'. The row status for this entry can be set to active only once the value of vRtrMplsAdminGroupValue has been set to a valid number in the range 0 to 31. The entry is destroyed when vRtrMplsAdminGroupRowStatus is set to 'destroy'.
TNA vRtrMplsAdminGroupName	1.3.6.1.4.1.6527.3.1.2.6.13.1.1	TNamedItem	not-accessible	The value of vRtrMplsAdminGroupName uniquely identifies the name of the administrative group within a virtual router instance.
ROW vRtrMplsAdminGroupRowStatus	1.3.6.1.4.1.6527.3.1.2.6.13.1.2	RowStatus	read-create	vRtrMplsAdminGroupRowStatus is used to create, delete or control entries in the vRtrMplsAdminGroupTable. To create a row entry, the row status should be set to 'createAndWait'. Before the row can be placed into the 'active' state, vRtrMplsAdminGroupValue must be set to a value between 0 and 31. To delete a row entry, the row status should be set to 'destroy'
vRtrMplsAdminGroupTable	1.3.6.1.4.1.6527.3.1.2.6.13		not-accessible	The vRtrMplsAdminGroupTable has an entry for each administrative group configured for the virtual router in the system. Administrative groups are resource constructs that define a link color or resource class. They provide the ability to classify network resources (links) into groups or colors based on zones, geographic location, link location, etc. By doing so, network administrators are able to do more granular traffic engineering of LSPs.
I32 vRtrMplsAdminGroupValue	1.3.6.1.4.1.6527.3.1.2.6.13.1.3	Integer32	read-create	The value of vRtrMplsAdminGroupValue specifies the group value associated with this administrative group. This value is unique within a virtual router instance. A value of -1 indicates that the group value for this entry has not been set.
I32 vRtrMplsARHopTunnelIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.6	Integer32	read-only	Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list (stores RRO in LSR).
I32 vRtrMplsERHopTunnelIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.5	Integer32	read-only	Primary index into the mplsTunnelHopTable identifying a particular recorded hop list (stores ERO in LSR).
U32 vRtrMplsFSGroupCost	1.3.6.1.4.1.6527.3.1.2.6.14.1.3	Unsigned32	read-create	The value of vRtrMplsFSGroupCost specifies the cost assigned to the fate sharing group. This cost is applied to all nodes and links that are part of this group and used for CSPF calculations. The higher the cost of the node or link, the lesser its chance of being selected as part of the path.
vRtrMplsFSGroupEntry	1.3.6.1.4.1.6527.3.1.2.6.14.1		not-accessible	Each row entry in the vRtrMplsFSGroupTable represents a fate sharing group which is a database of nodes and links that share common risk attributes. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupRowStatus to 'destroy'.
TNA vRtrMplsFSGroupName	1.3.6.1.4.1.6527.3.1.2.6.14.1.1	TNamedItem	not-accessible	The value of vRtrMplsFSGroupName uniquely identifies the name of the fate sharing group within a virtual router instance.
vRtrMplsFSGroupParamsEntry	1.3.6.1.4.1.6527.3.1.2.6.15.1		not-accessible	Each row entry in the vRtrMplsFSGroupParamsTable represents either a node or a link that is a part of a fate sharing group defined in the vRtrMplsFSGroupTable. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupParamsRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupParamsRowStatus to 'destroy'. To configure a node to be part of the group, create an entry in this table with vRtrMplsFSGroupParamsFromAddr set to a valid non-zero IP address and vRtrMplsFSGroupParamsToAddr set to 0. To configure a link to be part of the group, create an entry in this table with both vRtrMplsFSGroupParamsFromAddr and vRtrMplsFSGroupParamsToAddr set to valid non-zero IP addresses.
IP vRtrMplsFSGroupParamsFromAddr	1.3.6.1.4.1.6527.3.1.2.6.15.1.1	IpAddress	not-accessible	The value of vRtrMplsFSGroupParamsFromAddr along with the value of vRtrMplsFSGroupParamsToAddr uniquely identifies a link or node within a fate sharing group. This value must be non-zero for all row entries whether it represents a node or a link.
ROW vRtrMplsFSGroupParamsRowStatus	1.3.6.1.4.1.6527.3.1.2.6.15.1.3	RowStatus	read-create	vRtrMplsFSGroupParamsRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupParamsTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy'
vRtrMplsFSGroupParamsTable	1.3.6.1.4.1.6527.3.1.2.6.15		not-accessible	The vRtrMplsFSGroupParamsTable has an entry for each node or link that is part of a fate sharing group on this virtual router.
IP vRtrMplsFSGroupParamsToAddr	1.3.6.1.4.1.6527.3.1.2.6.15.1.2	IpAddress	not-accessible	The value of vRtrMplsFSGroupParamsToAddr along with the value of vRtrMplsFSGroupParamsFromAddr uniquely identifies a link or node within a fate sharing group. This value must be 0 for row entries that represent a node and must be non-zero for row entries that represent a link.
ROW vRtrMplsFSGroupRowStatus	1.3.6.1.4.1.6527.3.1.2.6.14.1.2	RowStatus	read-create	vRtrMplsFSGroupRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy'
vRtrMplsFSGroupTable	1.3.6.1.4.1.6527.3.1.2.6.14		not-accessible	The vRtrMplsFSGroupTable has an entry for each group that is a part of the fate sharing database configured for the virtual router in the system. A fate sharing group is used to define a group of links and nodes in the network that share common risk attributes. To minimize a single point of failure, backup paths can be created that not only avoid the nodes and links of the primary path but also any other nodes and links that share risk with the nodes and links of the primary path.
TMN vRtrMplsGeneralAdminState	1.3.6.1.4.1.6527.3.1.2.6.7.1.2	TmnxAdminState	read-create	When vRtrMplsGeneralAdminState is set to 'inService', the agent attempts to enable the MPLS protocol instance on this router. When vRtrMplsGeneralAdminState is set to 'outOfService', the agent attempts to disable the MPLS protocol instance on this router.
C32 vRtrMplsGeneralDetourLspOriginate	1.3.6.1.4.1.6527.3.1.2.6.8.1.7	Counter32	read-only	This object counts the number of detour LSPs that originate at this virtual router.
C32 vRtrMplsGeneralDetourLspTerminate	1.3.6.1.4.1.6527.3.1.2.6.8.1.9	Counter32	read-only	This object counts the number of detour LSPs that terminate at this virtual router.
C32 vRtrMplsGeneralDetourLspTransit	1.3.6.1.4.1.6527.3.1.2.6.8.1.8	Counter32	read-only	This object counts the number of detour LSPs that transit through this virtual router.
T/F vRtrMplsGeneralDynamicBypass	1.3.6.1.4.1.6527.3.1.2.6.7.1.11	TruthValue	read-create	The value of vRtrMplsGeneralDynamicBypass specifies whether dynamic bypass tunnels are enabled. By default, dynamic bypass tunnels are enabled.
C32 vRtrMplsGeneralDynamicLspOriginate	1.3.6.1.4.1.6527.3.1.2.6.8.1.4	Counter32	read-only	This object counts the number of dynamic LSPs that originate at this virtual router.
C32 vRtrMplsGeneralDynamicLspTerminate	1.3.6.1.4.1.6527.3.1.2.6.8.1.6	Counter32	read-only	This object counts the number of dynamic LSPs that terminate at this virtual router.
C32 vRtrMplsGeneralDynamicLspTransit	1.3.6.1.4.1.6527.3.1.2.6.8.1.5	Counter32	read-only	This object counts the number of dynamic LSPs that transit through this virtual router.
vRtrMplsGeneralEntry	1.3.6.1.4.1.6527.3.1.2.6.7.1		not-accessible	Each row entry represents an instance of the MPLS protocol running within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created by the agent when vRtrMplsStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrMplsStatus is set to 'delete'
T/F vRtrMplsGeneralFRObject	1.3.6.1.4.1.6527.3.1.2.6.7.1.8	TruthValue	read-create	The value of vRtrMplsGeneralFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsGeneralFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. The value for vRtrMplsGeneralFRObject is by default inherited by all LSPs.
U32 vRtrMplsGeneralHoldTimer	1.3.6.1.4.1.6527.3.1.2.6.7.1.10	Unsigned32	read-create	The value of vRtrMplsGeneralHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. A value of 0 indicates that the hold timer has been disabled.
TIM vRtrMplsGeneralLastChange	1.3.6.1.4.1.6527.3.1.2.6.7.1.1	TimeStamp	read-only	The sysUpTime when this row was last modified.
TES vRtrMplsGeneralNewLspIndex	1.3.6.1.4.1.6527.3.1.2.6.7.1.6	TestAndIncr	read-create	This object is used to assign values to vRtrMplsLspIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsLspEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions.
U32 vRtrMplsGeneralNextResignal	1.3.6.1.4.1.6527.3.1.2.6.7.1.12	Unsigned32	read-only	The value of vRtrMplsGeneralNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralResignalTimer to expire.
TMN vRtrMplsGeneralOperDownReason	1.3.6.1.4.1.6527.3.1.2.6.7.1.13	TmnxMplsOperDownReasonCode	read-only	The value of vRtrMplsGeneralOperDownReason indicates the reason due to which the MPLS instance is operationally down.
TMN vRtrMplsGeneralOperState	1.3.6.1.4.1.6527.3.1.2.6.7.1.3	TmnxOperState	read-only	vRtrMplsGeneralOperState indicates the current operating state of this MPLS protocol instance on this router.
U32 vRtrMplsGeneralOptimizeTimer	1.3.6.1.4.1.6527.3.1.2.6.7.1.7	Unsigned32	read-create	The value of vRtrMplsGeneralOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSPs. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. The value for vRtrMplsGeneralOptimizeTimer is by default inherited by all LSPs and their paths.
T/F vRtrMplsGeneralPropagateTtl	1.3.6.1.4.1.6527.3.1.2.6.7.1.4	TruthValue	read-create	When vRtrMplsGeneralPropagateTtl is set to 'true', for all LSPs, the ingress ESR writes the TTL of the IP packet in the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When vRtrMplsGeneralPropagateTtl is set to 'false', the ingress ESR ignores the IP packet TTl and writes the value of 255 into the label, while the egress ESR does not write the label TTL into the IP packet. This assumes that all ESRs have been configured to have vRtrMplsGeneralPropagateTtl set to 'false', or this may result in unpredictable behavior.
U32 vRtrMplsGeneralResignalTimer	1.3.6.1.4.1.6527.3.1.2.6.7.1.9	Unsigned32	read-create	The value of vRtrMplsGeneralResignalTimer specifies the value for the LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the LSPs. When the resignal timer expires, if the new recorded hop list (RRO) for an LSP has a better metric than the current recorded hop list, an attempt will be made to resignal that LSP using the make-before-break mechanism. If the attempt to resignal an LSP fails, the LSP will continue to use the existing path and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based LSP resignalling has been disabled.
T/F vRtrMplsGeneralSrlgFrr	1.3.6.1.4.1.6527.3.1.2.6.7.1.14	TruthValue	read-create	The value of vRtrMplsGeneralSrlgFrr specifies whether Shared Risk Link Group (SRLG) constraint will be used in the computation of FRR bypass or detour to be associated with any primary LSP path on the system. When the value of vRtrMplsGeneralSrlgFrr is 'true' the use of SRLG constraint is enabled. By default, the use of SRLG constraint is disabled.
T/F vRtrMplsGeneralSrlgFrrStrict	1.3.6.1.4.1.6527.3.1.2.6.7.1.15	TruthValue	read-create	The value of vRtrMplsGeneralSrlgFrrStrict specifies whether to associate the LSP with a bypass or signal a detour if a bypass or detour satisfies all other constraints except the SRLG constraints. When the value of vRtrMplsGeneralSrlgFrrStrict is 'true' and a path that meets SRLG constraints is not found, the bypass or detour is not setup. If this value is set to 'true' when vRtrMplsGeneralSrlgFrr is set to 'false', vRtrMplsGeneralSrlgFrr is set to 'true' also. By default, the value of vRtrMplsGeneralSrlgFrrStrict is 'false'.
vRtrMplsGeneralStatEntry	1.3.6.1.4.1.6527.3.1.2.6.8.1		not-accessible	Each row entry represents a collection of statistics for an instance of the MPLS protocol running within a virtual router. Entries cannot be created and deleted via SNMP SET operations.
C32 vRtrMplsGeneralStaticLspOriginate	1.3.6.1.4.1.6527.3.1.2.6.8.1.1	Counter32	read-only	This object counts the number of static LSPs that originate at this virtual router.
C32 vRtrMplsGeneralStaticLspTerminate	1.3.6.1.4.1.6527.3.1.2.6.8.1.3	Counter32	read-only	This object counts the number of static LSPs that terminate at this virtual router.
C32 vRtrMplsGeneralStaticLspTransit	1.3.6.1.4.1.6527.3.1.2.6.8.1.2	Counter32	read-only	This object counts the number of static LSPs that transit through this virtual router.
vRtrMplsGeneralStatTable	1.3.6.1.4.1.6527.3.1.2.6.8		not-accessible	The vRtrMplsGeneralStatTable contains statistics for an MPLS protocol instance within a virtual router.
vRtrMplsGeneralTable	1.3.6.1.4.1.6527.3.1.2.6.7		not-accessible	The vRtrMplsGeneralTable contains objects for general control and management of an MPLS protocol instance within a virtual router.
INT vRtrMplsGeneralTE	1.3.6.1.4.1.6527.3.1.2.6.7.1.5	INTEGER	read-create	The value of vRtrMplsGeneralTE specifies the type of traffic engineering used with this MPLS instance.
U32 vRtrMplsIfAdminGroup	1.3.6.1.4.1.6527.3.1.2.6.9.1.3	Unsigned32	read-create	The value of vRtrMplsIfAdminGroup is a bit-map that identifies the admin groups to which the interface belongs. If bit 'n' is set, then the interface belongs to the admin group with value 'n'. By default, the interface does not belong to any admin groups.
TMN vRtrMplsIfAdminState	1.3.6.1.4.1.6527.3.1.2.6.9.1.1	TmnxAdminState	read-create	The desired administrative state for the MPLS protocol running on this MPLS interface.
vRtrMplsIfEntry	1.3.6.1.4.1.6527.3.1.2.6.9.1		not-accessible	Each row entry represents an interface on this virtual router that participates in the MPLS protocol. A row cannot be created or deleted via SNMP SET requests. A row with default attribute values is created by setting the vRtrIfEntry attribute, vRtrIfMplsStatus, to 'create'. A row is removed if vRtrIfMplsStatus is set to 'delete'. However, an attempt to destroy a row will fail if vRtrMplsIfAdminState has not first been set to 'outOfService'.
TMN vRtrMplsIfOperState	1.3.6.1.4.1.6527.3.1.2.6.9.1.2	TmnxOperState	read-only	This variable indicates the current status of the MPLS protocol running on this MPLS interface.
C64 vRtrMplsIfRxOctetCount	1.3.6.1.4.1.6527.3.1.2.6.10.1.4	Counter64	read-only	The total number of bytes in MPLS labeled packets received on this interface.
C64 vRtrMplsIfRxPktCount	1.3.6.1.4.1.6527.3.1.2.6.10.1.2	Counter64	read-only	The total number of MPLS labeled packets received on this interface.
vRtrMplsIfSrlgGrpEntry	1.3.6.1.4.1.6527.3.1.2.6.23.1		not-accessible	Each row entry represents an SRLG group associated with a interface on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests.
TIM vRtrMplsIfSrlgGrpLastChanged	1.3.6.1.4.1.6527.3.1.2.6.23.1.3	TimeStamp	read-only	The value of vRtrMplsIfSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsIfSrlgGrpTable.
TNA vRtrMplsIfSrlgGrpName	1.3.6.1.4.1.6527.3.1.2.6.23.1.1	TNamedItem	not-accessible	The value of vRtrMplsIfSrlgGrpName indicates the SRLG group name.
ROW vRtrMplsIfSrlgGrpRowStatus	1.3.6.1.4.1.6527.3.1.2.6.23.1.2	RowStatus	read-create	vRtrMplsIfSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsIfSrlgGrpTable.
vRtrMplsIfSrlgGrpTable	1.3.6.1.4.1.6527.3.1.2.6.23		not-accessible	The vRtrMplsIfSrlgGrpTable has an entry for each Shared Risk Link Group (SRLG) groups associated with a router interface configured for MPLS in the system.
TIM vRtrMplsIfSrlgGrpTblLastChanged	1.3.6.1.4.1.6527.3.1.2.6.22	TimeStamp	read-only	The value of vRtrMplsIfSrlgGrpTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsIfSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.
NTF vRtrMplsIfStateChange	1.3.6.1.4.1.6527.3.1.3.6.0.2			This Notification is generated when the MPLS interface changes state
vRtrMplsIfStatEntry	1.3.6.1.4.1.6527.3.1.2.6.10.1		not-accessible	Each row entry represents a collection of statistics for an interface on this virtual router that participates in the MPLS protocol. Entries cannot be created and deleted via SNMP SET operations.
vRtrMplsIfStatTable	1.3.6.1.4.1.6527.3.1.2.6.10		not-accessible	The vRtrMplsIfStatTable has an entry for each router interface configured for MPLS in the system.
vRtrMplsIfTable	1.3.6.1.4.1.6527.3.1.2.6.9		not-accessible	The vRtrMplsIfTable has an entry for each router interface configured for MPLS in the system.
U32 vRtrMplsIfTeMetric	1.3.6.1.4.1.6527.3.1.2.6.9.1.4	Unsigned32	read-create	The value of vRtrMplsIfTeMetric specifies the traffic engineering metric for this interface. The TE metric is exchanged in addition to the IGP metric by the IGPs. Depending on the value configured for vRtrMplsLspCspfTeMetricEnabled, either the TE metric or the native IGP metric is used in CSPF computations of the LSP paths. The maximum value that can be configured is a 24 bit value.
C64 vRtrMplsIfTxOctetCount	1.3.6.1.4.1.6527.3.1.2.6.10.1.3	Counter64	read-only	The total number of bytes in MPLS labeled packets transmitted on this interface.
C64 vRtrMplsIfTxPktCount	1.3.6.1.4.1.6527.3.1.2.6.10.1.1	Counter64	read-only	The total number of MPLS labeled packets transmitted from this interface.
NUM vRtrMplsInSegmentIfIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.2	InterfaceIndexOrZero	read-only	An index of the mplsXCTable. It represents mplsInSegmentIfIndex of the mplsInSegmentTable.
MPL vRtrMplsInSegmentLabel	1.3.6.1.4.1.6527.3.1.2.6.6.1.3	MplsLabel	read-only	An index of the mplsXCTable. It represents mplsInSegmentLabel of the mplsInSegmentTable.
U32 vRtrMplsLabelRangeAging	1.3.6.1.4.1.6527.3.1.2.6.17.1.4	Unsigned32	read-only	The value of vRtrMplsLabelRangeAging represents the number of labels that are currently allocated and aging.
U32 vRtrMplsLabelRangeAvailable	1.3.6.1.4.1.6527.3.1.2.6.17.1.5	Unsigned32	read-only	The value of vRtrMplsLabelRangeAvailable represents the number of labels that are currently available for each label type.
vRtrMplsLabelRangeEntry	1.3.6.1.4.1.6527.3.1.2.6.17.1		not-accessible	Each row entry in the vRtrMplsLabelRangeTable represents a type of label. Each entry contains the label range used by that label type and the number of aging and allocated labels in the range.
U32 vRtrMplsLabelRangeMax	1.3.6.1.4.1.6527.3.1.2.6.17.1.3	Unsigned32	read-only	The value of vRtrMplsLabelRangeMax specifies the maximum label value in the range for a particular label type.
U32 vRtrMplsLabelRangeMin	1.3.6.1.4.1.6527.3.1.2.6.17.1.2	Unsigned32	read-only	The value of vRtrMplsLabelRangeMin specifies the minimum label value in the range for a particular label type.
vRtrMplsLabelRangeTable	1.3.6.1.4.1.6527.3.1.2.6.17		not-accessible	The vRtrMplsLabelRangeTable has an entry for each type of label, the minimum and maximum value in the label range and information on total available and aging labels in each range. This is a read-only table.
INT vRtrMplsLabelType	1.3.6.1.4.1.6527.3.1.2.6.17.1.1	INTEGER	not-accessible	The value of vRtrMplsLabelType specifies the type of label and is the index for this table.
T/F vRtrMplsLspAdaptive	1.3.6.1.4.1.6527.3.1.2.6.1.1.34	TruthValue	read-create	Setting the value of vRtrMplsLspAdaptive to 'true' enables make-before-break functionality for the LSP. When the attributes of an already established LSP are changed, either through manual configuration or due to a change in network topology, make-before-break functionality ensures that the resources of the existing LSP will not be released until a new path (with the same LSP Id) has been established and traffic flowing over the existing path is seamlessly transferred to the new path. Setting the value to 'false' disables make-before-break functionality.
U32 vRtrMplsLspAdminGroupExclude	1.3.6.1.4.1.6527.3.1.2.6.1.1.33	Unsigned32	read-create	The value of vRtrMplsLspAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP. This implies that each link that this LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list.
U32 vRtrMplsLspAdminGroupInclude	1.3.6.1.4.1.6527.3.1.2.6.1.1.32	Unsigned32	read-create	The value of vRtrMplsLspAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP. This implies that each link that this LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list.
TMN vRtrMplsLspAdminState	1.3.6.1.4.1.6527.3.1.2.6.1.1.5	TmnxAdminState	read-create	The desired administrative state for this LSP.
NUM vRtrMplsLspAge	1.3.6.1.4.1.6527.3.1.2.6.2.1.3	TimeInterval	read-only	The age (i.e., time from creation till now) of this LSP in 10-millisecond periods.
I32 vRtrMplsLspBandwidth	1.3.6.1.4.1.6527.3.1.2.6.1.1.24	Integer32	read-create	The value of vRtrMplsLspBandwidth specifies the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the LSP. A value of zero (0) indicates that no bandwidth is reserved. When vRtrMplsLspPathBandwidth is set to -1, the value of vRtrMplsLspBandwidth is applied to that specific LSP/path.
T/F vRtrMplsLspBwProtect	1.3.6.1.4.1.6527.3.1.2.6.1.1.25	TruthValue	read-create	When vRtrMplsLspBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources.
TNA vRtrMplsLspClassOfService	1.3.6.1.4.1.6527.3.1.2.6.1.1.19	TNamedItemOrEmpty	read-create	The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced. When the value of vRtrMplsLspPathCosSource is set to 'inherit', the value of vRtrMplsLspClassOfService is applied to that specific LSP/path.
I32 vRtrMplsLspConfiguredPaths	1.3.6.1.4.1.6527.3.1.2.6.2.1.11	Integer32	read-only	The number of paths configured for this LSP.
T/F vRtrMplsLspCspf	1.3.6.1.4.1.6527.3.1.2.6.1.1.15	TruthValue	read-create	When the value of vRtrMplsLspCspf is 'true', CSPF computation for constrained-path LSP is enabled. When the value of vRtrMplsLspCspf is 'false' CSPF computation is disabled.
T/F vRtrMplsLspCspfTeMetricEnabled	1.3.6.1.4.1.6527.3.1.2.6.1.1.40	TruthValue	read-create	The value of vRtrMplsLspCspfTeMetricEnabled specifies whether the TE metric would be used for the purpose of the LSP path computation by CSPF. When the value of this object is 'false', the IGP metric is used to compute the path of the LSP by CSPF.
T/F vRtrMplsLspDecrementTtl	1.3.6.1.4.1.6527.3.1.2.6.1.1.14	TruthValue	read-create	When the value of vRtrMplsLspDecrementTtl is 'true', the ingress ESR writes the TTL of the IP packet into the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When the value of vRtrMplsLspDecrementTtl is 'false', the ingress ESR ignores the IP packet TTL and writes the value of 255 into the label; and the egress ESR does not write the label's TTL into the IP packet.
NTF vRtrMplsLspDown	1.3.6.1.4.1.6527.3.1.3.6.0.4			This Notification is generated when a LSP transitions out of 'inService' state to any other state.
vRtrMplsLspEntry	1.3.6.1.4.1.6527.3.1.2.6.1.1		not-accessible	Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspName to have been assigned a valid value.
T/F vRtrMplsLspFastReroute	1.3.6.1.4.1.6527.3.1.2.6.1.1.16	TruthValue	read-create	When the value of vRtrMplsLspFastReroute is 'true', fast reroute is enabled. A pre-computed detour LSP is created from each node in the primary path of this LSP. In case of a failure of a link or LSP between two nodes, traffic is immediately rerouted on the pre-computed detour LSP thus avoiding packet loss. Each node along the primary path of the LSP tries to establish a detour LSP as follows: Each upstream node will setup a detour LSP that avoids only the immediate downstream node and merges back onto the actual path of the LSP as soon as possible. The detour LSP may take one or more hops (upto the value of vRtrMplsLspFRHopLimit) before merging back onto the main LSP path. When the upstream node detects a downstream link or node failure, it immediately send traffic for that LSP on the detour path and at the same time signals back to the ingress ESR about the failure. Fast reroute applies only to the primary path of this LSP. No configuration is required on the transit hops of the LSP. The ingress ESR will signal all intermediate ESRs using RSVP to setup their detours. When the value of vRtrMplsLspFastReroute is 'false', fast rerouting is disabled.
U32 vRtrMplsLspFRBandwidth	1.3.6.1.4.1.6527.3.1.2.6.1.1.18	Unsigned32	read-create	The value of vRtrMplsLspFRBandwidth specified the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the detour LSP. A value of zero (0) indicates that no bandwidth is reserved.
U32 vRtrMplsLspFRHopLimit	1.3.6.1.4.1.6527.3.1.2.6.1.1.17	Unsigned32	read-create	The value of vRtrMplsLspFRHopLimit specifies the total number of hops a detour LSP can take before merging back onto the main LSP path.
INT vRtrMplsLspFRMethod	1.3.6.1.4.1.6527.3.1.2.6.1.1.30	INTEGER	read-create	The value of vRtrMplsLspFRMethod specifies the fast reroute method used. In the 'One-to-one Backup' method, a backup LSP is established which will intersect the original LSP somewhere downstream of the point of link or node failure. For each LSP that is backed up, a separate backup LSP is established. In the 'Facility Backup' method, instead of creating a separate LSP for every LSP that is to be backed up, a single LSP is created which serves as a backup for a set of LSPs. Such an LSP tunnel is called a 'bypass tunnel'.
T/F vRtrMplsLspFRNodeProtect	1.3.6.1.4.1.6527.3.1.2.6.1.1.31	TruthValue	read-create	Setting the value of vRtrMplsLspFRNodeProtect to 'true' enables node protection i.e. protection against the failure of a node on the LSP. Setting the value to 'false' disables node protection.
T/F vRtrMplsLspFRObject	1.3.6.1.4.1.6527.3.1.2.6.1.1.38	TruthValue	read-create	The value of vRtrMplsLspFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsLspFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. When the vRtrMplsLspFRObject bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralFRObject.
IP vRtrMplsLspFromAddr	1.3.6.1.4.1.6527.3.1.2.6.1.1.7	IpAddress	read-create	Source IP address of this LSP. If vRtrMplsLspFromAddr has not been explicitly set, the system IP address will be used.
U32 vRtrMplsLspHoldPriority	1.3.6.1.4.1.6527.3.1.2.6.1.1.21	Unsigned32	read-create	The value of vRtrMplsLspHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathHoldPriority is set to '-1', the value of vRtrMplsLspHoldPriority is applied to that specific LSP/path.
U32 vRtrMplsLspHoldTimer	1.3.6.1.4.1.6527.3.1.2.6.1.1.39	Unsigned32	read-only	The value of vRtrMplsLspHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. The value of vRtrMplsLspHoldTimer is inherited from the value of vRtrMplsGeneralHoldTimer.
U32 vRtrMplsLspHopLimit	1.3.6.1.4.1.6527.3.1.2.6.1.1.26	Unsigned32	read-create	The value of vRtrMplsLspHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the value of vRtrMplsLspPathHopLimit is set to zero (0), the value of vRtrMplsLspHopLimit is applied to that specific LSP/path.
TMN vRtrMplsLspIndex	1.3.6.1.4.1.6527.3.1.2.6.1.1.1	TmnxVRtrMplsLspID	accessible-for-notify	The unique value which identifies this Labeled Switch Path (LSP) for this virtual router in the Alcatel 7x50 SR system. It is a unique value among entries with the same value of vRtrID.
U32 vRtrMplsLspInheritance	1.3.6.1.4.1.6527.3.1.2.6.1.1.35	Unsigned32	read-create	For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspInheritance that controls whether to inherit the operational value of the object or use the administratively set value. This object is a bit-mask, with the following positions: vRtrMplsLspOptimizeTimer 0x1 vRtrMplsLspFRObject 0x2 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable.
TIM vRtrMplsLspLastChange	1.3.6.1.4.1.6527.3.1.2.6.1.1.3	TimeStamp	read-only	The sysUpTime when this row was last modified.
NUM vRtrMplsLspLastPathChange	1.3.6.1.4.1.6527.3.1.2.6.2.1.10	TimeInterval	read-only	The time in 10-millisecond units since the last change occurred on this LSP.
NUM vRtrMplsLspLastTransition	1.3.6.1.4.1.6527.3.1.2.6.2.1.8	TimeInterval	read-only	The time in 10-millisecond units since the last transition occurred on this LSP.
U32 vRtrMplsLspMetric	1.3.6.1.4.1.6527.3.1.2.6.1.1.13	Unsigned32	read-create	The value of vRtrMplsLspMetric specifies the metric for this LSP which is used to select an LSP among a set of LSPs which are destined to the same egress 7x50 router. The LSP with the lowest metric will be selected. In LDP-over-RSVP, LDP performs a lookup in the Routing Table Manager (RTM) which provides the next hop to the destination PE and the advertising router (ABR or destination PE itself). If the advertising router matches the targeted LDP peer, LDP then performs a second lookup for the advertising router in the Tunnel Table Manager (TTM). This lookup returns the best RSVP LSP to use to forward packets for an LDP FEC learned through the targeted LDP session. The lookup returns the LSP with the lowest metric. If multiple LSPs have the same metric, then the result of the lookup will be to select the first one available in the TTM.
TNA vRtrMplsLspName	1.3.6.1.4.1.6527.3.1.2.6.1.1.4	TNamedItemOrEmpty	read-create	Administrative name for this Labeled Switch Path. The vRtrMplsLspName must be unique within a virtual router instance.
U32 vRtrMplsLspNegotiatedMTU	1.3.6.1.4.1.6527.3.1.2.6.1.1.27	Unsigned32	read-only	The value of vRtrMplsLspNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during LSP establishment.
INT vRtrMplsLspNotificationReasonCode	1.3.6.1.4.1.6527.3.1.2.6.16.1	INTEGER	accessible-for-notify	Used by vRtrMplsLspDown, the value indicates the reason for the LSP going down.
C64 vRtrMplsLspOctetsEx	1.3.6.1.4.1.6527.3.1.2.6.2.1.1	Counter64	read-only	The number of octets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment.
I32 vRtrMplsLspOperationalPaths	1.3.6.1.4.1.6527.3.1.2.6.2.1.13	Integer32	read-only	The number of operational paths for this LSP. This includes the path currently active, as well as operational standby paths.
T/F vRtrMplsLspOperFastReroute	1.3.6.1.4.1.6527.3.1.2.6.1.1.37	TruthValue	read-only	The value of vRtrMplsLspOperFastReroute specifies whether the operational LSP has fast reroute enabled or disabled. When make-before-break functionality for the LSP is enabled and if the fast reroute setting is changed, the resources for the existing LSP will not be released until a new path with the new attribute settings has been established. While a new path is being signaled, the administrative value and the operational values of fast reroute setting for the LSP may differ. The value of vRtrMplsLspFastReroute specifies the setting used for the new LSP path trying to be established whereas the value of vRtrMplsLspOperFastReroute specifies the setting for the existing LSP path.
TMN vRtrMplsLspOperState	1.3.6.1.4.1.6527.3.1.2.6.1.1.6	TmnxOperState	read-only	The current operational state of this LSP.
U32 vRtrMplsLspOptimizeTimer	1.3.6.1.4.1.6527.3.1.2.6.1.1.36	Unsigned32	read-create	The value of vRtrMplsLspOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspOptimizeTimer bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralOptimizeTimer.
I32 vRtrMplsLspOutSegIndx	1.3.6.1.4.1.6527.3.1.2.6.1.1.10	Integer32	read-create	The vRtrMplsLspOutSegIndx is the index value of the entry in the mplsOutSegmentTable associated with this vRtrMplsLspEntry when vRtrMplsLspType is 'static'. If vRtrMplsLspType is 'dynamic', the value of this object will be zero (0).
C64 vRtrMplsLspPackets	1.3.6.1.4.1.6527.3.1.2.6.2.1.2	Counter64	read-only	The number of packets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment.
T/F vRtrMplsLspPathAdaptive	1.3.6.1.4.1.6527.3.1.2.6.4.1.28	TruthValue	read-create	Setting the value of vRtrMplsLspPathAdaptive to 'true', enables make-before-break functionality for the LSP path. Setting the value to 'false', disables make-before-break functionality for the path. When the vRtrMplsLspPathAdaptive bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdaptive.
U32 vRtrMplsLspPathAdminGroupExclude	1.3.6.1.4.1.6527.3.1.2.6.4.1.27	Unsigned32	read-create	The value of vRtrMplsLspPathAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP path. This implies that each link that this LSP path goes through must not be associated with any of the admin groups in the exclude list. When the vRtrMplsLspPathAdminGroupExclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupExclude.
U32 vRtrMplsLspPathAdminGroupInclude	1.3.6.1.4.1.6527.3.1.2.6.4.1.26	Unsigned32	read-create	The value of vRtrMplsLspPathAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP path. This implies that each link that this LSP path goes through must be associated with at least one of the admin groups in the include list. When the vRtrMplsLspPathAdminGroupInclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupInclude.
TMN vRtrMplsLspPathAdminState	1.3.6.1.4.1.6527.3.1.2.6.4.1.17	TmnxAdminState	read-create	The desired administrative state for this LSP path.
I32 vRtrMplsLspPathBandwidth	1.3.6.1.4.1.6527.3.1.2.6.4.1.6	Integer32	read-create	The value of vRtrMplsLspPathBandwidth specifies the amount of bandwidth in mega-bits per seconds (Mbps) to be reserved for this LSP path. A value of zero (0) indicates that no bandwidth is reserved.
T/F vRtrMplsLspPathBwProtect	1.3.6.1.4.1.6527.3.1.2.6.4.1.7	TruthValue	read-create	When vRtrMplsLspPathBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources.
C32 vRtrMplsLspPathChanges	1.3.6.1.4.1.6527.3.1.2.6.2.1.9	Counter32	read-only	The number of path changes this LSP has had. For every path change (path down, path up, path change), a corresponding syslog/trap (if enabled) is generated for it.
TNA vRtrMplsLspPathClassOfService	1.3.6.1.4.1.6527.3.1.2.6.4.1.11	TNamedItemOrEmpty	read-create	The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspPathClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspPathClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced.
INT vRtrMplsLspPathCos	1.3.6.1.4.1.6527.3.1.2.6.4.1.4	INTEGER	read-create	The configured Class Of Service (COS) for this path. If the value is between 0 and 7 inclusive, this value will be inserted in the 3 bit COS field in the label. If the value is 255, the value in the COS field of the label will depend on other factors.
T/F vRtrMplsLspPathCosSource	1.3.6.1.4.1.6527.3.1.2.6.4.1.10	TruthValue	read-create	When vRtrMplsLspPathCosSource is set to 'true', the value of vRtrMplsLspPathClassOfService overrides vRtrMplsLspClassOfService. When 'false', the value of vRtrMplsLspClassOfService is used.
C32 vRtrMplsLspPathCspfQueries	1.3.6.1.4.1.6527.3.1.2.6.5.1.5	Counter32	read-only	The value of vRtrMplsLspPathCspfQueries specifies the number of CSPF queries that have been made for this LSP path.
NTF vRtrMplsLspPathDown	1.3.6.1.4.1.6527.3.1.3.6.0.6			This Notification is generated when a LSP Path transitions out of 'inService' state to any other state.
vRtrMplsLspPathEntry	1.3.6.1.4.1.6527.3.1.2.6.4.1		not-accessible	Each row entry represents an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries in this table can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspPathType to have been assigned a valid value.
TMN vRtrMplsLspPathFailCode	1.3.6.1.4.1.6527.3.1.2.6.4.1.24	TmnxMplsLspFailCode	read-only	The value of vRtrMplsLspPathFailCode specifies the reason code for LSP Path failure. A value of 0 indicates that no failure has occurred.
IP vRtrMplsLspPathFailNodeAddr	1.3.6.1.4.1.6527.3.1.2.6.4.1.25	IpAddress	read-only	The value of vRtrMplsLspPathFailNodeAddr specifies the IP address of the node in the LSP path at which the LSP path failed. When no failure has occurred, this value is 0.
U32 vRtrMplsLspPathHoldPriority	1.3.6.1.4.1.6527.3.1.2.6.4.1.13	Unsigned32	read-create	The value of vRtrMplsLspPathHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsLspPathHopLimit bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.
U32 vRtrMplsLspPathHopLimit	1.3.6.1.4.1.6527.3.1.2.6.4.1.15	Unsigned32	read-create	The value of vRtrMplsLspPathHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the vRtrMplsLspPathHopLimit bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.
U32 vRtrMplsLspPathInheritance	1.3.6.1.4.1.6527.3.1.2.6.4.1.19	Unsigned32	read-create	For each writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrMplsLspTable, controls whether to inherit the operational value of that object, or use the administratively set value. This object is a bit-mask, with the following positions: vRtrMplsLspPathBandwidth 0x10 vRtrMplsLspPathPreference 0x80 vRtrMplsLspPathSetupPriority 0x400 vRtrMplsLspPathHoldPriority 0x800 vRtrMplsLspPathHopLimit 0x2000 vRtrMplsLspPathAdminGroupInclude 0x20000 vRtrMplsLspPathAdminGroupExclude 0x40000 vRtrMplsLspPathAdaptive 0x80000 vRtrMplsLspPathOptimizeTimer 0x100000 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsLspTable.
TIM vRtrMplsLspPathLastChange	1.3.6.1.4.1.6527.3.1.2.6.4.1.2	TimeStamp	read-only	The sysUpTime when this row was last modified.
MPL vRtrMplsLspPathLspId	1.3.6.1.4.1.6527.3.1.2.6.4.1.20	MplsLSPID	read-only	This value identifies the label switched path that is signaled for this entry.
INT vRtrMplsLspPathMBBState	1.3.6.1.4.1.6527.3.1.2.6.4.1.32	INTEGER	read-only	The value of vRtrMplsLspPathMBBState specifies the state of the most recent invocation of the make-before-break functionality. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful inProgress (3) - make-before-break in progress fail (4) - make-before-break failed.
U32 vRtrMplsLspPathNegotiatedMTU	1.3.6.1.4.1.6527.3.1.2.6.4.1.23	Unsigned32	read-only	The value of vRtrMplsLspPathNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this LSP Path.
U32 vRtrMplsLspPathNextOptimize	1.3.6.1.4.1.6527.3.1.2.6.4.1.30	Unsigned32	read-only	The value of vRtrMplsLspPathNextOptimize specifies the current value of the optimize timer. This is the time, in seconds, remaining till the optimize timer will expire and optimization will be started for the LSP path.
TMN vRtrMplsLspPathNotificationReasonCode	1.3.6.1.4.1.6527.3.1.2.6.16.2	TmnxMplsLspFailCode	accessible-for-notify	Used by vRtrMplsLspPathDown, the value indicates the reason for the LSP path going down.
I32 vRtrMplsLspPathOperBandwidth	1.3.6.1.4.1.6527.3.1.2.6.4.1.31	Integer32	read-only	The value of vRtrMplsLspPathOperBandwidth specifies the amount of bandwidth in mega-bits per seconds (Mbps) that has been reserved for the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path bandwidth is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new bandwidth settings has been established. While a new path is being signaled, the administrative value and the operational values of the path bandwidth may differ. The value of vRtrMplsLspPathBandwidth specifies the bandwidth requirements for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperBandwidth specifies the bandwidth reserved for the existing LSP path.
U32 vRtrMplsLspPathOperMTU	1.3.6.1.4.1.6527.3.1.2.6.4.1.35	Unsigned32	read-only	The value of vRtrMplsLspPathOperMTU specifies the size for the Maximum transmission unit (MTU) that is currently operation for this LSP Path.
TMN vRtrMplsLspPathOperState	1.3.6.1.4.1.6527.3.1.2.6.4.1.18	TmnxOperState	read-only	The current operational state of this LSP path.
U32 vRtrMplsLspPathOptimizeTimer	1.3.6.1.4.1.6527.3.1.2.6.4.1.29	Unsigned32	read-create	The value of vRtrMplsLspPathOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP path. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspPathOptimizeTimer bit in vRtrMplsLspPathInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsLspOptimizeTimer.
INT vRtrMplsLspPathPreference	1.3.6.1.4.1.6527.3.1.2.6.4.1.9	INTEGER	read-create	When there is no path in the LSP with vRtrMplsLspPathType value of 'primary', 'secondary' type paths of this LSP with the same value of vRtrMplsLspPathPreference are used for load sharing. When a 'primary' type path exists in the LSP, vRtrMplsLspPathPreference is used to denote at which priority one 'secondary' path will supercede another when the 'primary' fails. 1 indicates the highest priority value. When the vRtrMplsLspPathPreference bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspPreference.
BIT vRtrMplsLspPathProperties	1.3.6.1.4.1.6527.3.1.2.6.4.1.5	Bits	read-only	The set of configured properties for this path expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value 1 is set.
INT vRtrMplsLspPathRecord	1.3.6.1.4.1.6527.3.1.2.6.4.1.14	INTEGER	read-create	When the value of vRtrMplsLspPathRecord is 'record', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecord is 'noRecord', recording of all the hops that a LSP traverses is disabled.
INT vRtrMplsLspPathRecordLabel	1.3.6.1.4.1.6527.3.1.2.6.4.1.36	INTEGER	read-create	When the value of vRtrMplsLspPathRecordLabel is 'record', recording of labels at each node that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecordLabel is 'noRecord', recording of labels at each node that a LSP traverses is disabled.
NTF vRtrMplsLspPathRerouted	1.3.6.1.4.1.6527.3.1.3.6.0.7			The vRtrMplsLspPathRerouted notification is generated when an LSP Path is rerouted.
TMN vRtrMplsLspPathResignal	1.3.6.1.4.1.6527.3.1.2.6.4.1.33	TmnxActionType	read-create	Setting the value of vRtrMplsLspPathResignal to 'doAction' triggers the re-signaling of the LSP path. If the LSP path is operationally down either due to network failure or due to the retry attempts count being exceeded, setting this variable to 'doAction' will initiate the signaling for the path. A make-before-break signaling for the path will be initiated if the LSP is operationally up but the make-before-break retry attempts count was exceeded. Make-before-break signaling will also be initiated for any LSP that is operationally up. This may be used to cause a loose-hop LSP to be optimized. If a re-signal is triggered while a re-signaling is already in progress, the old transient state will be destroyed and a new transaction being triggered. An SNMP GET request on this object should return 'notApplicable'.
NTF vRtrMplsLspPathResignaled	1.3.6.1.4.1.6527.3.1.3.6.0.8			The vRtrMplsLspPathResignaled notification is generated when an LSP Path is resignaled.
U32 vRtrMplsLspPathRetryAttempts	1.3.6.1.4.1.6527.3.1.2.6.5.1.3	Unsigned32	read-only	The number of unsuccessful attempts which have been made to signal this path. As soon as the path gets signalled, this is set to 0.
U32 vRtrMplsLspPathRetryTimeRemaining	1.3.6.1.4.1.6527.3.1.2.6.4.1.21	Unsigned32	read-only	The time in 10-millisecond units to signal this path.
ROW vRtrMplsLspPathRowStatus	1.3.6.1.4.1.6527.3.1.2.6.4.1.1	RowStatus	read-create	The row status used for creation, deletion, or control of vRtrMplsLspPathTable entries. Before the row can be placed into the 'active' state vRtrMplsLspPathType must have been assigned a valid value.
U32 vRtrMplsLspPathSetupPriority	1.3.6.1.4.1.6527.3.1.2.6.4.1.12	Unsigned32	read-create	The value of vRtrMplsLspPathSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsLspPathHopLimit bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit.
T/F vRtrMplsLspPathSharing	1.3.6.1.4.1.6527.3.1.2.6.4.1.16	TruthValue	read-create	When vRtrMplsLspPathSharing has a value of 'true', path-sharing is enabled for the secondary path. Path-sharing is used to control the hops of the secondary path. When vRtrMplsLspPathSharing have a value of 'false', CSPF attempts to find a path for the secondary that does not include any node or link that is common to the active primary path. This variable is valid only if vRtrMplsLspPathType is set to 'secondary'.
INT vRtrMplsLspPathState	1.3.6.1.4.1.6527.3.1.2.6.4.1.8	INTEGER	read-only	The current working state of this path within this LSP.
vRtrMplsLspPathStatEntry	1.3.6.1.4.1.6527.3.1.2.6.5.1		not-accessible	Each row entry represents a collection of statistics for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries cannot be created and deleted via SNMP SET operations.
vRtrMplsLspPathStatTable	1.3.6.1.4.1.6527.3.1.2.6.5		not-accessible	The vRtrMplsLspPathStatTable has an entry for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable.
vRtrMplsLspPathTable	1.3.6.1.4.1.6527.3.1.2.6.4		not-accessible	The vRtrMplsLspPathTable provides an association between an LSP and a path. An LSP can have more than one path association, but only one of those paths can be specified as the primary path type. Paths are defined in as Tunnel entries in the mplsTunnelTable in the MPLS-TE-MIB.
TES vRtrMplsLspPathTableSpinlock	1.3.6.1.4.1.6527.3.1.2.6.3	TestAndIncr	read-write	voluntary serialization control for vRtrMplsLspPathTable. Primarily used by SNMP manager to coordinate changes to vRtrMplsLspPathInheritance.
NUM vRtrMplsLspPathTimeDown	1.3.6.1.4.1.6527.3.1.2.6.5.1.2	TimeInterval	read-only	The total time in 10-millisecond units that this LSP Path has not been operational.
NUM vRtrMplsLspPathTimeUp	1.3.6.1.4.1.6527.3.1.2.6.5.1.1	TimeInterval	read-only	The total time in 10-millisecond units that this LSP path has been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspPathTimeUp/vRtrMplsLspAge * 100 %).
C32 vRtrMplsLspPathTransitionCount	1.3.6.1.4.1.6527.3.1.2.6.5.1.4	Counter32	read-only	The object vRtrMplsLspPathTransitionCount maintains the number of transitions that have occurred for this LSP.
I32 vRtrMplsLspPathTunnelARHopListIndex	1.3.6.1.4.1.6527.3.1.2.6.4.1.22	Integer32	read-only	Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list. A value of 0 implies that there is no recored hop list associated with this LSP path.
I32 vRtrMplsLspPathTunnelCRHopListIndex	1.3.6.1.4.1.6527.3.1.2.6.4.1.34	Integer32	read-only	Primary index into the vRtrMplsTunnelCHopTable identifying a particular computed hop list. A value of 0 implies that there is no computed hop list associated with this LSP path.
INT vRtrMplsLspPathType	1.3.6.1.4.1.6527.3.1.2.6.4.1.3	INTEGER	read-create	This variable is an enum that represents the role this path is taking within this LSP.
NTF vRtrMplsLspPathUp	1.3.6.1.4.1.6527.3.1.3.6.0.5			This Notification is generated when a LSP Path transitions to the 'inService' state from any other state.
U32 vRtrMplsLspPreference	1.3.6.1.4.1.6527.3.1.2.6.1.1.23	Unsigned32	read-create	The value of vRtrMplsLspPreference specifies the preference for the LSP. This value is used for load balancing between multiple LSPs that exist between the same ingress and egress routers. By default, traffic is load balanced among the LSPs, since all LSPs have the same preference. To prefer one LSP over another, change the preference value for that LSP. The LSP with the lowest preference is used. When the value of vRtrMplsLspPathPreference is set to zero (0), the value of vRtrMplsLspPreference is applied to that specific LSP/path.
NUM vRtrMplsLspPrimaryTimeUp	1.3.6.1.4.1.6527.3.1.2.6.2.1.6	TimeInterval	read-only	The total time in 10-millisecond units that this LSP's primary path has been operational. For example, the percentage contribution of the primary path to the operational time is given by (vRtrMplsLspPrimaryTimeUp/vRtrMplsLspTimeUp * 100) %.
T/F vRtrMplsLspRecord	1.3.6.1.4.1.6527.3.1.2.6.1.1.22	TruthValue	read-create	When the value of vRtrMplsLspRecord is 'true', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspRecord is 'false, recording of all the hops that a LSP traverses is disabled.
U32 vRtrMplsLspRetryLimit	1.3.6.1.4.1.6527.3.1.2.6.1.1.12	Unsigned32	read-create	The value of vRtrMplsLspRetryLimit specifies the number of attempts the software should make to reestablish a failed LSP before the LSP is disabled. A value of 0 indicates that an infinite number of retry attempts should be made.
U32 vRtrMplsLspRetryTimer	1.3.6.1.4.1.6527.3.1.2.6.1.1.11	Unsigned32	read-create	The value of vRtrMplsLspRetryTimer specifies the time in seconds the software will wait before attempting the establish the failed LSP.
ROW vRtrMplsLspRowStatus	1.3.6.1.4.1.6527.3.1.2.6.1.1.2	RowStatus	read-create	The row status used for creation, deletion, or control of vRtrMplsLspTable entries. Before the row can be placed into the 'active' state vRtrMplsLspName must have been assigned a valid value.
T/F vRtrMplsLspRsvpAdspec	1.3.6.1.4.1.6527.3.1.2.6.1.1.29	TruthValue	read-create	When the value of vRtrMplsLspRsvpAdspec is 'true', the ADSPEC object will be included in RSVP messages. When the value of vRtrMplsLspRsvpAdspec is 'false', the ADSPEC object will not be included in RSVP messages.
INT vRtrMplsLspRsvpResvStyle	1.3.6.1.4.1.6527.3.1.2.6.1.1.28	INTEGER	read-create	The value of vRtrMplsLspRsvpResvStyle specifies the reservation style for RSVP. The reservation style can be set to 'Shared- Explicit' (se) or 'Fixed-Filter' (ff).
U32 vRtrMplsLspSetupPriority	1.3.6.1.4.1.6527.3.1.2.6.1.1.20	Unsigned32	read-create	The value of vRtrMplsLspSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathSetupPriority is set to '-1', the value of vRtrMplsLspSetupPriority is applied to that specific LSP/path.
I32 vRtrMplsLspStandbyPaths	1.3.6.1.4.1.6527.3.1.2.6.2.1.12	Integer32	read-only	The number of standby paths configured for this LSP.
vRtrMplsLspStatEntry	1.3.6.1.4.1.6527.3.1.2.6.2.1		not-accessible	Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations.
vRtrMplsLspStatTable	1.3.6.1.4.1.6527.3.1.2.6.2		not-accessible	The vRtrMplsLspStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.
vRtrMplsLspTable	1.3.6.1.4.1.6527.3.1.2.6.1		not-accessible	The vRtrMplsLspTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system.
NUM vRtrMplsLspTimeDown	1.3.6.1.4.1.6527.3.1.2.6.2.1.5	TimeInterval	read-only	The total time in 10-millisecond units that this LSP has not been operational.
NUM vRtrMplsLspTimeUp	1.3.6.1.4.1.6527.3.1.2.6.2.1.4	TimeInterval	read-only	The total time in 10-millisecond units that this LSP has been been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspTimeUp/vRtrMplsLspAge * 100 %).
IP vRtrMplsLspToAddr	1.3.6.1.4.1.6527.3.1.2.6.1.1.8	IpAddress	read-create	Destination IP address of this LSP. This LSP will not be signaled until vRtrMplsLspToAddr is explicitly set.
C32 vRtrMplsLspTransitions	1.3.6.1.4.1.6527.3.1.2.6.2.1.7	Counter32	read-only	The number of state transitions (up -> down and down -> up) this LSP has undergone.
INT vRtrMplsLspType	1.3.6.1.4.1.6527.3.1.2.6.1.1.9	INTEGER	read-create	The vRtrMplsLspType object is an enumerated value that indicates whether the label value is statically or dynamically assigned or whether the LSP will be used exclusively for bypass protection.
NTF vRtrMplsLspUp	1.3.6.1.4.1.6527.3.1.3.6.0.3			This Notification is generated when a LSP transitions to the 'inService' state from any other state.
NUM vRtrMplsNotifyRow	1.3.6.1.4.1.6527.3.1.2.6.16.3	RowPointer	accessible-for-notify	used by Alcatel 7x50 SR series MPLS Configuration change Notifications, the object ID indicates the MPLS table and entry.
I32 vRtrMplsOutSegmentIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.4	Integer32	read-only	An index of the mplsXCTable. It represents mplsOutSegmentIndex of the mplsOutSegmentTable.
U32 vRtrMplsRsvpSessionIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.7	Unsigned32	read-only	An index into the vRtrRsvpSessionTable identifying a particular RSVP session.
vRtrMplsSrlgGrpEntry	1.3.6.1.4.1.6527.3.1.2.6.21.1		not-accessible	Each row entry represents a SRLG group on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests.
TIM vRtrMplsSrlgGrpLastChanged	1.3.6.1.4.1.6527.3.1.2.6.21.1.3	TimeStamp	read-only	The value of vRtrMplsSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgGrpTable.
TNA vRtrMplsSrlgGrpName	1.3.6.1.4.1.6527.3.1.2.6.21.1.1	TNamedItem	not-accessible	The value of vRtrMplsSrlgGrpName indicates the SRLG group name.
ROW vRtrMplsSrlgGrpRowStatus	1.3.6.1.4.1.6527.3.1.2.6.21.1.2	RowStatus	read-create	vRtrMplsSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsSrlgGrpTable. A value must also be set for vRtrMplsSrlgGrpValue before the row entry can transition to the 'active' state.
vRtrMplsSrlgGrpTable	1.3.6.1.4.1.6527.3.1.2.6.21		not-accessible	The vRtrMplsSrlgGrpTable has an entry for each Shared Risk Link Groups (SRLG) group configured for MPLS in the system.
TIM vRtrMplsSrlgGrpTableLastChanged	1.3.6.1.4.1.6527.3.1.2.6.20	TimeStamp	read-only	The value of vRtrMplsSrlgGrpTableLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value.
U32 vRtrMplsSrlgGrpValue	1.3.6.1.4.1.6527.3.1.2.6.21.1.4	Unsigned32	read-create	The value of vRtrMplsSrlgGrpValue specifies the group value associated with vRtrMplsSrlgGrpName. This value is unique within a virtual router instance. At the time of row creation, a value for vRtrMplsSrlgGrpValue must be specified or else row creation would fail.
NTF vRtrMplsStateChange	1.3.6.1.4.1.6527.3.1.3.6.0.1			This Notification is generated when the MPLS module changes state
MPL vRtrMplsStaticLSPLabel	1.3.6.1.4.1.6527.3.1.2.6.18.1.1	MplsLabel	not-accessible	The value of vRtrMplsStaticLSPLabel specifies the label value.
vRtrMplsStaticLSPLabelEntry	1.3.6.1.4.1.6527.3.1.2.6.18.1		not-accessible	Each row entry in the vRtrMplsStaticLSPLabelTable represents a label of type static LSP that is currently allocated. The entry includes information about the current owner for that label.
TMN vRtrMplsStaticLSPLabelOwner	1.3.6.1.4.1.6527.3.1.2.6.18.1.2	TmnxMplsLabelOwner	read-only	The value of vRtrMplsStaticLSPLabelOwner specifies the owner for the label value vRtrMplsStaticLSPLabel.
vRtrMplsStaticLSPLabelTable	1.3.6.1.4.1.6527.3.1.2.6.18		not-accessible	The vRtrMplsStaticLSPLabelTable has an entry for each allocated label that is part of the static LSP label range. This is a read-only table.
MPL vRtrMplsStaticSvcLabel	1.3.6.1.4.1.6527.3.1.2.6.19.1.1	MplsLabel	not-accessible	The value of vRtrMplsStaticSvcLabel specifies the label value.
vRtrMplsStaticSvcLabelEntry	1.3.6.1.4.1.6527.3.1.2.6.19.1		not-accessible	Each row entry in the vRtrMplsStaticSvcLabelTable represents a label of type static-svc that is currently allocated. The entry includes information about the current owner for that label.
TMN vRtrMplsStaticSvcLabelOwner	1.3.6.1.4.1.6527.3.1.2.6.19.1.2	TmnxMplsLabelOwner	read-only	The value of vRtrMplsStaticSvcLabelOwner specifies the owner for the label value vRtrMplsStaticSvcLabel.
vRtrMplsStaticSvcLabelTable	1.3.6.1.4.1.6527.3.1.2.6.19		not-accessible	The vRtrMplsStaticSvcLabelTable has an entry for each allocated label that is part of the static service label range. This is a read-only table.
vRtrMplsTunnelARHopEntry	1.3.6.1.4.1.6527.3.1.2.6.11.1		not-accessible	A row entry in this table corresponds to a row entry in the mplsTunnelARHopTable and adds to the information contained in that table
BIT vRtrMplsTunnelARHopProtection	1.3.6.1.4.1.6527.3.1.2.6.11.1.1	Bits	read-only	If the 'localAvailable' bit is set, it indicates that the link downstream of this node has been protected by means of a local repair mechanism. This mechanism can be either the one-to-one backup method or the facility backup method. If the 'localInUse' bit is set, then it indicates that the local protection mechanism is being used to maintain this tunnel. If the 'bandwidthProtected' bit is set, then it indicates that the backup path is guaranteed to provide the desired bandwidth. If the 'nodeProtected' bit is set, then it indicates that the backup path provides protection against the failure of the next LSR along the LSP.
MPL vRtrMplsTunnelARHopRecordLabel	1.3.6.1.4.1.6527.3.1.2.6.11.1.2	MplsLabel	read-only	If label recording is enabled, vRtrMplsTunnelARHopRecordLabel specifies the label that is advertised to the previous hop in the hop list. If label recording is disabled, vRtrMplsTunnelARHopRecordLabel will have a value of 4294967295
IP vRtrMplsTunnelARHopRouterId	1.3.6.1.4.1.6527.3.1.2.6.11.1.3	IpAddress	read-only	vRtrMplsTunnelARHopRouterId specifies the router ID of the node corresponding to this hop.
vRtrMplsTunnelARHopTable	1.3.6.1.4.1.6527.3.1.2.6.11		not-accessible	The vRtrMplsTunnelARHopTable augments the mplsTunnelARHopEntry in the MPLS-TE-MIB.
INT vRtrMplsTunnelCHopAddrType	1.3.6.1.4.1.6527.3.1.2.6.12.1.3	INTEGER	read-only	Denotes the address type of this tunnel hop.
INT vRtrMplsTunnelCHopAsNumber	1.3.6.1.4.1.6527.3.1.2.6.12.1.8	INTEGER	read-only	If vRtrMplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact.
vRtrMplsTunnelCHopEntry	1.3.6.1.4.1.6527.3.1.2.6.12.1		not-accessible	An entry in this table represents a CSPF tunnel hop. Entries are created and deleted by the system.
I32 vRtrMplsTunnelCHopIndex	1.3.6.1.4.1.6527.3.1.2.6.12.1.2	Integer32	not-accessible	Secondary index into this table identifying a particular hop.
IP vRtrMplsTunnelCHopIpv4Addr	1.3.6.1.4.1.6527.3.1.2.6.12.1.4	IpAddress	read-only	If vRtrMplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contain a value of 0.
INT vRtrMplsTunnelCHopIpv4PrefixLen	1.3.6.1.4.1.6527.3.1.2.6.12.1.5	INTEGER	read-only	If vRtrMplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0.
ADR vRtrMplsTunnelCHopIpv6Addr	1.3.6.1.4.1.6527.3.1.2.6.12.1.6	InetAddressIPv6	read-only	If the vRtrMplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0.
INT vRtrMplsTunnelCHopIpv6PrefixLen	1.3.6.1.4.1.6527.3.1.2.6.12.1.7	INTEGER	read-only	If vRtrMplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0.
I32 vRtrMplsTunnelCHopListIndex	1.3.6.1.4.1.6527.3.1.2.6.12.1.1	Integer32	not-accessible	Primary index into this table identifying a particular explicit route object.
MPL vRtrMplsTunnelCHopLspId	1.3.6.1.4.1.6527.3.1.2.6.12.1.9	MplsLSPID	read-only	If vRtrMplsTunnelCHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled through this hop (using label stacking). This object is otherwise insignificant and should contain a value of 0 to indicate this fact.
INT vRtrMplsTunnelCHopStrictOrLoose	1.3.6.1.4.1.6527.3.1.2.6.12.1.10	INTEGER	read-only	Denotes whether this tunnel hop is routed in a strict or loose fashion.
vRtrMplsTunnelCHopTable	1.3.6.1.4.1.6527.3.1.2.6.12		not-accessible	The vRtrMplsTunnelCHopTable is used to hold the CSPF path for a detour LSP. Each entry indicates a single hop. Primary index is the vRtrMplsTunnelCHopListIndex which associates multiple entries (hops) in the vRtrMplsTunnelCHopTable to a single mplsTunnelEntry specified in the mplsTunnelTable. The first row in the table is the first hop after the origination point of the tunnel.
I32 vRtrMplsXCCHopTableIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.9	Integer32	read-only	Index to the vRtrMplsTunnelCHopTable entries that specify the hops for the CSPF path for a detour LSP for this tunnel.
vRtrMplsXCEntry	1.3.6.1.4.1.6527.3.1.2.6.6.1		not-accessible	An entry in this table represents the indices to be used to search the mplsXCTable.
TMN vRtrMplsXCFailCode	1.3.6.1.4.1.6527.3.1.2.6.6.1.8	TmnxMplsLspFailCode	read-only	The value of vRtrMplsXCFailCode specifies the reason code for cross-connect failure. A value of 0 indicates that no failure occurred.
I32 vRtrMplsXCIndex	1.3.6.1.4.1.6527.3.1.2.6.6.1.1	Integer32	read-only	An index of the mplsXCTable. It represents mplsXCIndex, a field of the mplsXCTable.
vRtrMplsXCTable	1.3.6.1.4.1.6527.3.1.2.6.6		not-accessible	This table has an entry for each mplsXCEntry in the mplsXCTable. It serves as an another indirect index to the mplsXCTable.

RFC description

Alcatel-Lucent vendor-private MIB for MPLS (Multiprotocol Label Switching) management and forwarding operations.

Start monitoring Nokia (Alcatel-Lucent) 7750 SR-series service routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-TIMETRA-MPLS-MIB