ADTRAN-ACTDAX-MIB

All MIBs › ADTRAN-ACTDAX-MIB

Category: DSL and Broadband, Vendor: ADTRAN

Description: Manages ADTRAN ACTDAX DSL access equipment, providing line configuration, status, and performance monitoring objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ADTRAN-ACTDAX-MIB?

ADTRAN-ACTDAX-MIB is a vendor-specific SNMP module for ADTRAN's ACTDAX DSL access equipment, providing configuration and monitoring objects for DSL access lines. It exposes DSL line configuration parameters and performance/status data for the copper access lines terminated on the device. Its monitoring value is centered on line/interface hardware status — line configuration state and performance monitoring counters typical of DSL access equipment (e.g., line rate, error counts) used to confirm subscriber DSL lines are performing within acceptable limits. It likely builds on standard DSL-related MIBs (such as HDSL2-SHDSL-LINE-MIB or similar ADSL line MIBs) given the DSL access equipment domain, though no module description or sample objects were extracted to confirm this directly. It is deployed at telco or ISP access points where ADTRAN ACTDAX equipment terminates subscriber DSL lines. Network engineers evaluating or troubleshooting this functionality can download the ADTRAN-ACTDAX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ADTRAN-ACTDAX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADTRAN ACTDAX DSL access equipment

Monitoring Examples

No sample object names were extracted for this module, so specific table or scalar names cannot be confirmed. An administrator would typically poll this MIB's DSL line configuration and performance objects to confirm subscriber lines are synced at expected rates and free of excessive errors, revealing a degraded or failing DSL line. Concrete object names should be verified against the actual MIB source since none were supplied here.

What Can Be Monitored

DSL line configuration
line sync/rate status
line error/performance counters

Imported Objects

From ADTRAN-DS1-MIB

adDS1AlarmIndex	OBJECT-TYPE
adDS1AlertIndex	OBJECT-TYPE
adDS1CurrentAlert	OBJECT-TYPE
adDS1FarCurrentAlert	OBJECT-TYPE
adDS1FarTotalAlert	OBJECT-TYPE
adDS1LineEvent	OBJECT-TYPE
adDS1TotalAlert	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString
snmp

From RFC1406-MIB

dsx1LineStatus

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF coldStart	1.3.6.1.2.1.11.0.0			A coldStart trap signifes that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered.
adtran	1.3.6.1.4.1.664
adProducts	1.3.6.1.4.1.664.1
adACTDAX	1.3.6.1.4.1.664.1.2
NTF ds1Alarm	1.3.6.1.4.1.664.1.2.0.201			A DS1 Alarm Trap indicates a DS1 Line Status bit has changed state, producing an Alarm Event for the DS1 interface. The bit map Line Events variable identifies the alarm event(s). The bit map Line Status variable contains the interface status when the alarm occurred. Only enabled (arm set) status produce an Alarm Trap. Alarm event/status bit values: 1 No Alarm 2 Receive Yellow Alarm 4 Transmit Yellow Alarm 8 Receive Alarm Indication Signal (AIS) 16 Transmit AIS 32 RED Alarm 64 LOSS, Loss Of Receive Signal 128 Loopback 2048 Receive Test Code
NTF ds1Alert	1.3.6.1.4.1.664.1.2.0.202			A DS1 Threshold Crossing Alert has occurred. The Performance Parameters which have exceeded their Threshold Values are identified in the bit mapped Alert variables for the Near End and Far End DS1 interface. Parameters identify Alerts for the Current 15 minute interval and Total variables. Threshold Crossing Alert bit values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Second 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations
adMgmt	1.3.6.1.4.1.664.2
adACTDAXmg	1.3.6.1.4.1.664.2.2
adACTDAXconfig	1.3.6.1.4.1.664.2.2.1
STR adACTDAXpassword	1.3.6.1.4.1.664.2.2.1.1	DisplayString	read-write	The password string used for authentication of SNMP messages between Proxy Agent and ACTDAX.
STR adACTDAXtime	1.3.6.1.4.1.664.2.2.1.2	DisplayString	read-write	The current ACTDAX time value. A sequence of ASCII characters encoded as HR-Hour, MN-Minute, SC-Second. For example, HRMNSC = 123059.
STR adACTDAXdate	1.3.6.1.4.1.664.2.2.1.3	DisplayString	read-write	The current ACTDAX date value. A sequence of ASCII characters encoded as MN-Month, DY-Day, YR-Year. For example, MNDYYR = 073193.
INT adACTDAXresetPM	1.3.6.1.4.1.664.2.2.1.4	INTEGER	read-write	Resets Performance Monitor DS1 statistic counters in ACTDAX. Parameter value 1 resets all lines, 2 resets line 1 (DS1-A), 3 resets line 2 (DS1-B).
STR adACTDAXphone	1.3.6.1.4.1.664.2.2.1.5	DisplayString	read-write	The dialing sequence (phone number) to reach the network manager.
INT adACTDAXselfTestA	1.3.6.1.4.1.664.2.2.1.6	INTEGER	read-write	Perform local loopback self-test on DS1 line A.
INT adACTDAXtestStatusA	1.3.6.1.4.1.664.2.2.1.7	INTEGER	read-write	Local loopback self-test status for DS1 line A.
INT adACTDAXselfTestB	1.3.6.1.4.1.664.2.2.1.8	INTEGER	read-write	Perform local loopback self-test on DS1 line B.
INT adACTDAXtestStatusB	1.3.6.1.4.1.664.2.2.1.9	INTEGER	read-write	Local loopback self-test status for DS1 line B.

RFC description

Management information for the ADTRAN ACTDAX T1/E1 LIU controller used in channel bank applications.

Start monitoring ADTRAN ACTDAX DSL access equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ADTRAN-ACTDAX-MIB

What Is ADTRAN-ACTDAX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description