All MIBs › ADTRAN-ADUNIT-MIB
Organization: ADTRAN, Inc.
Last Updated: 2002-01-25
Category: Device Management, Vendor: ADTRAN
Description: Provides base unit management objects for ADTRAN network access devices including system identity and hardware status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ADTRAN-ADUNIT-MIB?
ADTRAN-ADUNIT-MIB is an ADTRAN vendor-specific MIB (module adtranUnitMib, under the shared adShared enterprise branch) that models general unit-level configuration and status for ADTRAN network access devices, independent of any specific card or port. It exposes system identity and boot information (adUnitBootRevision), general configuration (adUnitDateTime, adUnitMaxTelnetAccess, adUnitEncryptPasswords, adUnitEventLogging), utility/maintenance actions (adUnitRebootSystem, adUnitFactoryDefaultSystem, adUnitSchedResetTime), a local user-authentication table (adUnitUserTable, keyed by adUnitUserIndex with name, auth method, idle timeout, access level, and RowStatus), and TFTP firmware/configuration transfer state via the AdTftpConfigXferStatus textual convention (idle, download/upload in-progress, failed, checksum errors, and more). Monitoring it surfaces whether firmware or configuration transfers are progressing or have failed, and whether local user accounts and telnet access limits are configured as expected. It depends on the ADTRAN-TC and ADTRAN-MIB modules for shared types and the base adShared OID subtree, and is deployed alongside ADTRAN's per-slot and per-port MIBs on the same access device. Network teams can download the ADTRAN-ADUNIT-MIB file to load base unit management into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ADTRAN-ADUNIT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ADTRAN network access devices (access router / IAD product lines sharing the adShared MIB tree)
Monitoring Examples
An operator polls the TFTP transfer status object (typed AdTftpConfigXferStatus) after pushing a firmware update to confirm it reaches tftpDownloadComplete rather than tftpDownloadFailed or tftpBadFileChecksum, and cross-checks adUnitUserTable entries' adUnitUserStatus to verify no unexpected accounts were added via adUnitFactoryDefaultSystem resets.
What Can Be Monitored
- boot PROM revision
- TFTP firmware/config transfer status
- local user account table and access levels
- telnet session limits
- event log enable/clear state
- scheduled reset time
This MIB depends on
Related MIBs
Imported Objects
From ADTRAN-MIB
| adShared | OBJECT-IDENTITY |
From ADTRAN-TC
| AdPresence | |
| AdProductIdentifier |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| PhysAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| adtranUnitMib | 1.3.6.1.4.1.664.5.30 | The MIB module for general unit configuration. | ||
| adUnitInfo | 1.3.6.1.4.1.664.5.30.1 | |||
| STR adUnitBootRevision | 1.3.6.1.4.1.664.5.30.1.1 | DisplayString | read-only | Unit boot PROM revision. |
| adUnitConfig | 1.3.6.1.4.1.664.5.30.2 | |||
| adUnitGenCfg | 1.3.6.1.4.1.664.5.30.2.1 | |||
| DAT adUnitDateTime | 1.3.6.1.4.1.664.5.30.2.1.1 | DateAndTime | read-write | The current unit date and time. |
| I32 adUnitMaxTelnetAccess | 1.3.6.1.4.1.664.5.30.2.1.2 | Integer32 | read-write | The maximum number of active telnet sessions. |
| INT adUnitEncryptPasswords | 1.3.6.1.4.1.664.5.30.2.1.3 | INTEGER | read-write | Determines whether or not the locally stored user passwords are encrypted. |
| INT adUnitEventLogging | 1.3.6.1.4.1.664.5.30.2.1.4 | INTEGER | read-write | Enable/Disable event logging on the unit. |
| I32 adUnitClearEventLog | 1.3.6.1.4.1.664.5.30.2.1.5 | Integer32 | read-write | Set to 1 to clear all entries from unit's local event log. |
| adUserCfg | 1.3.6.1.4.1.664.5.30.2.2 | |||
| adUnitUserTable | 1.3.6.1.4.1.664.5.30.2.2.1 | not-accessible | A list of users who are allowed access to the unit. | |
| adUnitUserEntry | 1.3.6.1.4.1.664.5.30.2.2.1.1 | not-accessible | Each entry in the list defines the user/pass, authen method, access level, and timeout. | |
| I32 adUnitUserIndex | 1.3.6.1.4.1.664.5.30.2.2.1.1.1 | Integer32 | not-accessible | Sequential index of the list of defined users. |
| STR adUnitUserName | 1.3.6.1.4.1.664.5.30.2.2.1.1.2 | DisplayString | read-create | The user name for access. |
| INT adUnitUserAuthenMethod | 1.3.6.1.4.1.664.5.30.2.2.1.1.3 | INTEGER | read-create | The type of authentication to perform for this user. |
| STR adUnitUserPasswd | 1.3.6.1.4.1.664.5.30.2.2.1.1.4 | DisplayString | read-create | The user password |
| I32 adUnitUserIdleTime | 1.3.6.1.4.1.664.5.30.2.2.1.1.5 | Integer32 | read-create | The idle timeout value in minutes for a connection. If no operator activity is detected for this interval the connection is terminated. If the value is set to 0, the session will not be disconnected due to inactivity. |
| I32 adUnitUserLevel | 1.3.6.1.4.1.664.5.30.2.2.1.1.6 | Integer32 | read-create | This is the level of access this user has. |
| STR adUnitUserIpAddr | 1.3.6.1.4.1.664.5.30.2.2.1.1.7 | DisplayString | read-create | If not null, the only IP address (or hostname) from which the specified user may initiate a telnet access. |
| INT adUnitUserState | 1.3.6.1.4.1.664.5.30.2.2.1.1.8 | INTEGER | read-only | Indication of whether or not the user has an active session. |
| ROW adUnitUserStatus | 1.3.6.1.4.1.664.5.30.2.2.1.1.9 | RowStatus | read-create | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitUserStatus column is 'notReady'. |
| adSnmpCfg | 1.3.6.1.4.1.664.5.30.2.3 | |||
| adUnitSNMPCommunitiesTable | 1.3.6.1.4.1.664.5.30.2.3.1 | not-accessible | Contains a list of users who have SNMP access to this unit. | |
| adUnitSNMPCommunitiesEntry | 1.3.6.1.4.1.664.5.30.2.3.1.1 | not-accessible | Each entry in the list defines the community string, access privilege, and Manager IP address. | |
| I32 adUnitSNMPCommunitiesIndex | 1.3.6.1.4.1.664.5.30.2.3.1.1.1 | Integer32 | not-accessible | Index of the table. |
| STR adUnitSNMPCommunitiesString | 1.3.6.1.4.1.664.5.30.2.3.1.1.2 | DisplayString | read-create | The community string which has the specified SNMP access. |
| INT adUnitSNMPCommunitiesPrivilege | 1.3.6.1.4.1.664.5.30.2.3.1.1.3 | INTEGER | read-create | Set the SNMP privileges of this user. |
| IP adUnitSNMPCommunitiesMngmtIP | 1.3.6.1.4.1.664.5.30.2.3.1.1.4 | IpAddress | read-create | The IP address of the manager station. Set to '0.0.0.0' to enable the string for all addresses. |
| ROW adUnitSNMPCommunitiesStatus | 1.3.6.1.4.1.664.5.30.2.3.1.1.5 | RowStatus | read-create | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitSNMPCommunitiesStatus column is 'notReady'. |
| adUnitSNMPTrapsTable | 1.3.6.1.4.1.664.5.30.2.3.2 | not-accessible | Contains a list of users that will receive SNMP traps from this unit. | |
| adUnitSNMPTrapsEntry | 1.3.6.1.4.1.664.5.30.2.3.2.1 | not-accessible | Each entry in the list defines the name, privilege, and Manager IP address. | |
| I32 adUnitSNMPTrapsIndex | 1.3.6.1.4.1.664.5.30.2.3.2.1.1 | Integer32 | not-accessible | Index of the table. |
| STR adUnitSNMPTrapsString | 1.3.6.1.4.1.664.5.30.2.3.2.1.2 | DisplayString | read-create | The community string included in the SNMP traps. |
| STR adUnitSNMPTrapsMngmtAddr | 1.3.6.1.4.1.664.5.30.2.3.2.1.3 | DisplayString | read-create | The hostname (or IP address) that will receive SNMP traps. |
| ROW adUnitSNMPTrapsStatus | 1.3.6.1.4.1.664.5.30.2.3.2.1.4 | RowStatus | read-create | The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitSNMPTrapsStatus column is 'notReady'. |
| INT adUnitSNMPEnableTraps | 1.3.6.1.4.1.664.5.30.2.3.3 | INTEGER | read-write | Enables or disables the transmission of all Traps. |
| INT adUnitSNMPAuthenticationTraps | 1.3.6.1.4.1.664.5.30.2.3.4 | INTEGER | read-write | Enables or disables the transmission of Authentication Traps. |
| adConsoleCfg | 1.3.6.1.4.1.664.5.30.2.4 | |||
| INT adConsoleAccessMode | 1.3.6.1.4.1.664.5.30.2.4.1 | INTEGER | read-write | Specify operational mode of console. 0: No Authentication; no login required, CLI active automatically 1: Password Only 2: Username and password required |
| STR adConsolePasswd | 1.3.6.1.4.1.664.5.30.2.4.2 | DisplayString | read-write | The password for the console. |
| I32 adConsoleLoginTimeout | 1.3.6.1.4.1.664.5.30.2.4.3 | Integer32 | read-write | Specifies the amount of time the system will wait for user input for a username &/or password before timing out and resetting back to intial prompt state. The time is specified in seconds. If the value is set to 0, the session will not be disconnected due to inactivity. Some units may implement a maximum allowable which is less than that specified. |
| INT adConsoleBaudRate | 1.3.6.1.4.1.664.5.30.2.4.4 | INTEGER | read-write | The baud rate for the console port. |
| INT adConsoleDataBits | 1.3.6.1.4.1.664.5.30.2.4.5 | INTEGER | read-write | The data bits for the console port. |
| INT adConsoleParity | 1.3.6.1.4.1.664.5.30.2.4.6 | INTEGER | read-write | The parity scheme for the console port. |
| INT adConsoleStopBits | 1.3.6.1.4.1.664.5.30.2.4.7 | INTEGER | read-write | The number of stop bits for the console port. |
| INT adConsoleFlowControl | 1.3.6.1.4.1.664.5.30.2.4.8 | INTEGER | read-write | The flow control mechanism for the console port. hardware control is via RTS/CTS and xOn/xOff is via transmission of the characters Control-S and Control-Q. Units may not support both control methods & hence may reject attempts to Set to ones not supported . |
| STR adConsoleModemInitString | 1.3.6.1.4.1.664.5.30.2.4.9 | DisplayString | read-write | Initialization string to send to connected modem. |
| I32 adConsoleInitModem | 1.3.6.1.4.1.664.5.30.2.4.10 | Integer32 | read-write | Set value to 1 to force unit to attempt to initialize a connected modem on the console port by sending the contents of adConsoleModemInitString. |
| adUnitSyslogCfg | 1.3.6.1.4.1.664.5.30.2.5 | |||
| INT adUnitSyslogTransmission | 1.3.6.1.4.1.664.5.30.2.5.1 | INTEGER | read-write | Enables or disables the transmission of log events to the external Syslog server. |
| STR adUnitSyslogSrvrName | 1.3.6.1.4.1.664.5.30.2.5.2 | DisplayString | read-write | The Host IP Address specifies the hostname or IP address of the external server that is running the Syslog host daemon. |
| INT adUnitSyslogHostFacility | 1.3.6.1.4.1.664.5.30.2.5.3 | INTEGER | read-write | The Host Facility specifies the facility destination of log events. Facilities are located on the host and are managed by the Syslog host daemon running on either a UNIX machine or a PC. |
| INT adUnitSyslogMinSeverity | 1.3.6.1.4.1.664.5.30.2.5.4 | INTEGER | read-write | MinSeverity Level specifies the minimum level of severity that will cause messages to be logged to the Syslog server. The levels are listed in order of decreasing severity and any message at or above the selected severity level will be logged if transmission is enabled. 1. Emergency: system is unusable 2. Alert: action must be taken immediately 3. Critical: critical conditions 4. Error: error conditions 5. Warning: warning conditions 6. Notice: normal, but significant, conditions 7. Info: informational message 8. Debug: debug-level message |
| adUnitUtil | 1.3.6.1.4.1.664.5.30.3 | |||
| adUnitGenUtil | 1.3.6.1.4.1.664.5.30.3.1 | |||
| I32 adUnitRebootSystem | 1.3.6.1.4.1.664.5.30.3.1.1 | Integer32 | read-write | Set to 1 to initiate system reboot. |
| I32 adUnitFactoryDefaultSystem | 1.3.6.1.4.1.664.5.30.3.1.2 | Integer32 | read-write | Set to 1 to set factory defaults configuration values for the entire unit. |
| DAT adUnitSchedResetTime | 1.3.6.1.4.1.664.5.30.3.1.3 | DateAndTime | read-write | Date and Time of scheduled system reset. |
| adUpdtFirmware | 1.3.6.1.4.1.664.5.30.3.2 | |||
| INT adUpdtFwXfrMethod | 1.3.6.1.4.1.664.5.30.3.2.1 | INTEGER | read-write | Method of downloading firmware to the unit. |
| STR adUpdtFwTFTPSrvAddr | 1.3.6.1.4.1.664.5.30.3.2.2 | DisplayString | read-write | The hostname or IP address of the TFTP server. |
| STR adUpdtFwTFTPSrvFileName | 1.3.6.1.4.1.664.5.30.3.2.3 | DisplayString | read-write | The TFTP Server filename. |
| STR adUpdtFwXfrStatus | 1.3.6.1.4.1.664.5.30.3.2.4 | DisplayString | read-only | Status of the current transfer. |
| I32 adUpdtFwXfrModule | 1.3.6.1.4.1.664.5.30.3.2.5 | Integer32 | read-write | The module (slot) to update with the Firmware transfer. |
| INT adUpdtFwXfrControl | 1.3.6.1.4.1.664.5.30.3.2.6 | INTEGER | read-write | Start the current firmware transfer by setting value to 1 and stop a transfer in progress by setting value to 0. |
| adXferConfig | 1.3.6.1.4.1.664.5.30.3.3 | |||
| INT adUnitXferConfigMethod | 1.3.6.1.4.1.664.5.30.3.3.1 | INTEGER | read-write | Method to download/upload the unit's configuration. |
| INT adUnitXferConfigType | 1.3.6.1.4.1.664.5.30.3.3.2 | INTEGER | read-write | Format of the configuration file. |
| STR adUnitConfigTFTPSrvAddr | 1.3.6.1.4.1.664.5.30.3.3.3 | DisplayString | read-write | Hostname or IP address of the TFTP server. |
| STR adUnitConfigTFTPSrvFileName | 1.3.6.1.4.1.664.5.30.3.3.4 | DisplayString | read-write | The filename to download/upload from the TFTP server. |
| ADT adUnitConfigCurrXfrStatus | 1.3.6.1.4.1.664.5.30.3.3.5 | AdTftpConfigXferStatus | read-only | The status of the current configuration file transfer. |
| ADT adUnitConfigPrevXfrStatus | 1.3.6.1.4.1.664.5.30.3.3.6 | AdTftpConfigXferStatus | read-only | The status of the previous the configuration file transfer. |
| I32 adUpdtConfigXfrModule | 1.3.6.1.4.1.664.5.30.3.3.7 | Integer32 | read-write | If 0 through 35 is selected, the source or destination module (slot) for the configuration transfer. If -1 is selected the entire configuration is transfered. |
| INT adUnitXferConfig | 1.3.6.1.4.1.664.5.30.3.3.8 | INTEGER | read-write | Set value to 1 to transfer the configuration file from the tftp server and switch to the configuration. Set value to 2 to transfer the configuration file to the tftp server. |
| adUnitCpuUtil | 1.3.6.1.4.1.664.5.30.3.4 | |||
| G32 adUnitCurrentCpuUtil | 1.3.6.1.4.1.664.5.30.3.4.1 | Gauge32 | read-only | Average CPU utilization over the last second. |
| G32 adUnitTotalCpuUtil | 1.3.6.1.4.1.664.5.30.3.4.2 | Gauge32 | read-only | Average CPU utilization since last system reboot or statistics reset. |
| I32 adUnitClearUtilizationStats | 1.3.6.1.4.1.664.5.30.3.4.3 | Integer32 | read-write | Set value to 1 to clear CPU utilization statistics. |
| adUnitPing | 1.3.6.1.4.1.664.5.30.3.5 | |||
| INT adUnitPingStatus | 1.3.6.1.4.1.664.5.30.3.5.1 | INTEGER | read-write | Set value to 1 to Stop ping sequence and 2 to start ping sequence. |
| BIT adUnitPingMode | 1.3.6.1.4.1.664.5.30.3.5.2 | Bits | read-write | Set the 'sweep' BIT to cause the ping process to send consecutively increasing buffer sizes starting at adUnitPingPktMinSize and continueing to adUnitPingPktMaxSize. If 'sweep' is not set, a single packet size of adUnitPingPktMinSize is used. The default is for sweep to not be set. Set the 'verbose' bit for responses to be reported via entries in the adUnitPingRespTbl. If 'verbose' is not set, results are reported via adUnitPingResult. The default is for verbose to not be set. |
| STR adUnitPingTarget | 1.3.6.1.4.1.664.5.30.3.5.3 | DisplayString | read-write | Host name or IP Address of the unit to ping. |
| I32 adUnitPingPktMinSize | 1.3.6.1.4.1.664.5.30.3.5.4 | Integer32 | read-write | If in normal mode specifies the size of the ping request buffer. In Sweep mode the mininum initial size. |
| I32 adUnitPingPktMaxSize | 1.3.6.1.4.1.664.5.30.3.5.5 | Integer32 | read-write | Not used in normal mode. In Sweep mode, the maximum buffer size used for the sweep. If the value is not greater than adUnitPingPktMinSize the sweep will terminate after the first buffer size completes. |
| OCT adUnitPingFillBuffer | 1.3.6.1.4.1.664.5.30.3.5.6 | OCTET STRING | read-write | Specify the characters to replicate within the outgoing request buffer. |
| IP adUnitPingSource | 1.3.6.1.4.1.664.5.30.3.5.7 | IpAddress | read-write | The IP Address to be inserted into source field of transmitted message. If set to the default of 0.0.0.0, the address of the source network interface ( determined from the route table) is used. |
| I32 adUnitPingTimeout | 1.3.6.1.4.1.664.5.30.3.5.8 | Integer32 | read-write | Specify the Timeout for each ping request, specified in seconds. |
| I32 adUnitPingRepeatCnt | 1.3.6.1.4.1.664.5.30.3.5.9 | Integer32 | read-write | Specify the number of times to repeat the ping request. For verbose mode maximum allowed is 50, for normal mode, the maximum is 255. |
| I32 adUnitPingXmtNum | 1.3.6.1.4.1.664.5.30.3.5.10 | Integer32 | read-only | The actual number of ping requests transmitted. |
| I32 adUnitPingRcvNum | 1.3.6.1.4.1.664.5.30.3.5.11 | Integer32 | read-only | The number of respsones received |
| STR adUnitPingResult | 1.3.6.1.4.1.664.5.30.3.5.12 | DisplayString | read-write | Output string to show results of ping when in normal mode. If more than 255 transmissions are generated during the ping execution only the results of the first 255 are reported. The following characters indicate the specified results: ! OK . Timeout, no response U Destination Unreachable Q Source Quench (destination too busy) M Could not fragment ? Unknown Packet type & Packet lifetime exceeded |
| I32 adUnitPingMinRndTrp | 1.3.6.1.4.1.664.5.30.3.5.13 | Integer32 | read-only | The minimum round-trip time in milliseconds. |
| I32 adUnitPingMaxRndTrp | 1.3.6.1.4.1.664.5.30.3.5.14 | Integer32 | read-only | The maximum round-trip time in milliseconds. |
| I32 adUnitPingAvgRndTrp | 1.3.6.1.4.1.664.5.30.3.5.15 | Integer32 | read-only | The average round-trip time in milliseconds. |
| adUnitPingVerboseTable | 1.3.6.1.4.1.664.5.30.3.5.16 | not-accessible | A table reporting the verbose output of the last ping test initiated via SNMP. | |
| adUnitPingVerboseEntry | 1.3.6.1.4.1.664.5.30.3.5.16.1 | not-accessible | Each entry in the list is the result of a single ping request. Each request is identified by its sequence number, adPingRespIndex. | |
| I32 adPingRespIndex | 1.3.6.1.4.1.664.5.30.3.5.16.1.1 | Integer32 | not-accessible | The ping response sequence number. |
| INT adPingRespStatus | 1.3.6.1.4.1.664.5.30.3.5.16.1.2 | INTEGER | read-only | The compeletion status of the ping response: 1 - OK 2 - Target address is unknown 3 - Invalid Source address 4 - No response received before timeout expired 5 - Unreachable destination (adPingRespAddr contains reporting address) 6 - TTL expired in transit (adPingRespAddr contains reporting address) |
| IP adPingRespAddr | 1.3.6.1.4.1.664.5.30.3.5.16.1.3 | IpAddress | read-only | The reply from address. |
| I32 adPingRespSize | 1.3.6.1.4.1.664.5.30.3.5.16.1.4 | Integer32 | read-only | Buffer Size of the response. |
| I32 adPingRespTime | 1.3.6.1.4.1.664.5.30.3.5.16.1.5 | Integer32 | read-only | Time in milliseconds to receive response. |
| I32 adPingRespTTL | 1.3.6.1.4.1.664.5.30.3.5.16.1.6 | Integer32 | read-only | TTL value of the response. For TTL to be reported, the buffer size of the request (adUnitPingPktSize) must be at least 4 bytes. |
| adUnitTraceRt | 1.3.6.1.4.1.664.5.30.3.6 | |||
| INT adUnitTraceRtStatus | 1.3.6.1.4.1.664.5.30.3.6.1 | INTEGER | read-write | Set value to 0 to interrupt and stop a TraceRoute sequence and 1 to start a TraceRoute sequence. When TraceRoute completes value with change from 'active' to 'inActive'. |
| STR adUnitTraceRtTarget | 1.3.6.1.4.1.664.5.30.3.6.2 | DisplayString | read-write | Host name or IP Address of the unit to probe. |
| IP adUnitTraceRtSource | 1.3.6.1.4.1.664.5.30.3.6.3 | IpAddress | read-write | The IP Address to be inserted into source field of transmitted message. If set to the default of 0.0.0.0, the unit address is used. |
| I32 adUnitTraceRtTimeout | 1.3.6.1.4.1.664.5.30.3.6.4 | Integer32 | read-write | The response timeout for all traceroute probes. |
| I32 adUnitTraceRtProbeCnt | 1.3.6.1.4.1.664.5.30.3.6.5 | Integer32 | read-write | The number of probes to initiate for each TTL. |
| I32 adUnitTraceRtMinTTL | 1.3.6.1.4.1.664.5.30.3.6.6 | Integer32 | read-write | The Minimum Time To Live value (hops) of the traceroute probes. |
| I32 adUnitTraceRtMaxTTL | 1.3.6.1.4.1.664.5.30.3.6.7 | Integer32 | read-write | Specify the Maximum Time To Live value (hops) of the traceroute probes. |
| I32 adUnitTraceRtPortNum | 1.3.6.1.4.1.664.5.30.3.6.8 | Integer32 | read-write | Set the base UDP port number used in probes. Traceroute operation is based on the fact that nothing is listening on UDP ports base to base + nhops - 1 at the destination host (so an ICMP PORT_UNREACHABLE message will be returned to terminate the route tracing). If something is listening on a port in the default range, this option can be used to pick an unused port range. |
| adUnitTraceRtRespTable | 1.3.6.1.4.1.664.5.30.3.6.9 | not-accessible | A table reporting the output of each traceroute probe initiated via SNMP. Upon initiation of a traceroute any existing entries in the table are automatically deleted by the agent & new records are inserted to reflect the results of the most recent traceroute test. | |
| adUnitTraceRtRespEntry | 1.3.6.1.4.1.664.5.30.3.6.9.1 | not-accessible | Each entry in the list is the result of a single probe request intiated by traceroute. Each request is identified by its TTL number, adTraceRtRespIndex. When a trace route is started all entries are deleted from the table and then inserted as the result of each attempt is determined | |
| I32 adTraceRtRespIndex | 1.3.6.1.4.1.664.5.30.3.6.9.1.1 | Integer32 | not-accessible | The traceroute response sequence number (TTL). |
| STR adTraceRtRespString | 1.3.6.1.4.1.664.5.30.3.6.9.1.2 | DisplayString | read-only | The response output from the traceroute process for each probe. |
| adUnitStatus | 1.3.6.1.4.1.664.5.30.4 | |||
| OCT adUnitFaceplate | 1.3.6.1.4.1.664.5.30.4.1 | OCTET STRING | read-only | A bit encoded string representing the status of all faceplate indicators, LEDs, & switches for GUI visualization of the unit. Each product defines this as a bitmap of booleans, or a byte for each indicator if not binary. The strings from all the slots are concatenated into this one object, after prefixing each card indicator string with two bytes. The first byte contains the slot number as an integer, and the second byte contains the remaining string length for that slot. The Textual Convention AdDualLEDstatus should be used for non-binary states. |
| OCT adUnitAlarmStatus | 1.3.6.1.4.1.664.5.30.4.2 | OCTET STRING | read-only | A bit encoded string representing a summary of the alarm state of the chassis. Refer to individual unit documentation for the specification of the bimask |
| adUnitSlots | 1.3.6.1.4.1.664.5.30.5 | |||
| adUnitSlotInfoTable | 1.3.6.1.4.1.664.5.30.5.1 | not-accessible | Table of slots available for boards. | |
| adUnitSlotInfoEntry | 1.3.6.1.4.1.664.5.30.5.1.1 | not-accessible | General information descibing the contents of each card slot. | |
| I32 adUnitSlotInfoIndex | 1.3.6.1.4.1.664.5.30.5.1.1.1 | Integer32 | not-accessible | A unique value for each slot. Its value may exceed the value of adUnitSlotNumber if pseudo slot numbers are used for some bank commons or multiplexers. |
| STR adUnitSlotProdName | 1.3.6.1.4.1.664.5.30.5.1.1.2 | DisplayString | read-only | The Adtran Product Name. |
| STR adUnitSlotProdPartNumber | 1.3.6.1.4.1.664.5.30.5.1.1.3 | DisplayString | read-only | The Adtran Product Part Number. |
| STR adUnitSlotProdCLEIcode | 1.3.6.1.4.1.664.5.30.5.1.1.4 | DisplayString | read-only | The Adtran Product CLEI Code. |
| STR adUnitSlotProdSerialNumber | 1.3.6.1.4.1.664.5.30.5.1.1.5 | DisplayString | read-only | The Adtran Product Serial Number. |
| STR adUnitSlotProdRevision | 1.3.6.1.4.1.664.5.30.5.1.1.6 | DisplayString | read-only | The Adtran Product Revision Number. |
| STR adUnitSlotProdSwVersion | 1.3.6.1.4.1.664.5.30.5.1.1.7 | DisplayString | read-only | The Adtran Product Software Version Number. |
| PHY adUnitSlotProdPhysAddress | 1.3.6.1.4.1.664.5.30.5.1.1.8 | PhysAddress | read-only | This octet string variable contains the Adtran Physical Address assigned to this product. For example the octet sequence, 16 02 03 01, specifies channel bank number 16, digroup number 2, DS0 channel slot number 3, position 1. This object value is commonly reported in SNMP Traps to identify the product's location. |
| ADP adUnitSlotInfoState | 1.3.6.1.4.1.664.5.30.5.1.1.9 | AdPresence | read-only | The state of the card slot. Initially it is empty. When a card is inserted, it becomes occupied, and the Slot Type is determined by the card Product Code. When a card is removed, it changes to virtual, and retains the SlotType characteristics until a different kind of card is inserted, or a different preconfiguration is established. |
| OID adUnitSlotProduct | 1.3.6.1.4.1.664.5.30.5.1.1.10 | AdProductIdentifier | read-only | The ADTRAN Product code, 0 if empty. Agent will report real product code when installed or pre-provisioned. |
| INT adUnitSlotTrapEnable | 1.3.6.1.4.1.664.5.30.5.1.1.11 | INTEGER | read-write | Enables/Disables traps initiated from this slot. |
| OCT adUnitSlotAlarmStatus | 1.3.6.1.4.1.664.5.30.5.1.1.12 | OCTET STRING | read-only | A bit encoded string representing the alarm state of the slot. The LSB should be 1 for No Alarm, else 0 and the higher order bits will indicate which alarms are present. The specific alarm conditions may be found in more specific generic MIBs or in the device MIB. |
| OCT adUnitSlotFaceplate | 1.3.6.1.4.1.664.5.30.5.1.1.13 | OCTET STRING | read-only | A bit encoded string representing the status of faceplate indicators, LEDs, & switches for GUI visualization associated with the card in the respective slot. Each product defines this as a bitmap of booleans, or a byte for each indicator if not binary. The Textual Convention AdDualLEDstatus should be used for non-binary states. |
| INT adUnitSlotServiceState | 1.3.6.1.4.1.664.5.30.5.1.1.14 | INTEGER | read-write | Module service state. The full enumeration is supported by CND products. END products may support only the following subset with the END equivalent state following '/': is -- InService / Online oosUas -- Out of Service, Unasssigned / Unavailable oosMA -- Out of Sevice, Maint. / Offline |
| adUnitPort | 1.3.6.1.4.1.664.5.30.6 | |||
| adUnitPortInfoTable | 1.3.6.1.4.1.664.5.30.6.3 | not-accessible | A table of hardware oriented port information on each card. This only includes actual card ports, and not layered logical interfaces. | |
| adUnitPortInfoEntry | 1.3.6.1.4.1.664.5.30.6.3.1 | not-accessible | A row table entry exists for each card/port pair. | |
| I32 adUnitPortInfoIndex | 1.3.6.1.4.1.664.5.30.6.3.1.1 | Integer32 | not-accessible | A unique value for each physical port on a card. |
| ADP adUnitPortInfoState | 1.3.6.1.4.1.664.5.30.6.3.1.2 | AdPresence | read-only | The state of the card port. Initially it is empty. |
| I32 adUnitPortIfIndex | 1.3.6.1.4.1.664.5.30.6.3.1.3 | Integer32 | read-only | The interface number identified as ifIndex from the MIB-II interfaces table as defined by the slot and port numbers in this device. |
| OCT adUnitPortAlarmStatus | 1.3.6.1.4.1.664.5.30.6.3.1.4 | OCTET STRING | read-only | A bit encoded string representing the alarm state of the port. |
| STR adUnitPortDescription | 1.3.6.1.4.1.664.5.30.6.3.1.5 | DisplayString | read-write | A character string to identify the name of a port. Used for trap varbind in last trap sent. Should default to port number string. Can be overridden by customer as desired. |
| adUnitPortSlotMapTable | 1.3.6.1.4.1.664.5.30.6.4 | not-accessible | Table to map ifIndex to slot, port & type. | |
| adUnitPortSlotMapEntry | 1.3.6.1.4.1.664.5.30.6.4.1 | not-accessible | An entry exists for each interface which is mapped to a physical slot/port pair. | |
| I32 adUnitSlotAddress | 1.3.6.1.4.1.664.5.30.6.4.1.1 | Integer32 | read-only | The slot in which this port is contained. Slot 0 is reported for the unit controller and all logical interfaces. |
| I32 adUnitPortAddress | 1.3.6.1.4.1.664.5.30.6.4.1.2 | Integer32 | read-only | The port number within the slot. Logical interfaces should indicate port 0. |
| adUnitConformance | 1.3.6.1.4.1.664.5.30.7 | |||
| adUnitCompliances | 1.3.6.1.4.1.664.5.30.7.1 | |||
| adUnitCompliance | 1.3.6.1.4.1.664.5.30.7.1.1 | The compliance statement for SNMPv2 entities which implement the adUnit MIB. | ||
| adUnitMIBGroups | 1.3.6.1.4.1.664.5.30.7.2 | |||
| adUnitBaseGroup | 1.3.6.1.4.1.664.5.30.7.2.1 | The Unit Base Group. | ||
| adUnitUserGroup | 1.3.6.1.4.1.664.5.30.7.2.2 | The Unit Telnet Group. | ||
| adUnitSNMPConfigGroup | 1.3.6.1.4.1.664.5.30.7.2.3 | The Unit SNMP Config Group. | ||
| adUnitMaintConsoleGroup | 1.3.6.1.4.1.664.5.30.7.2.4 | The Unit Maintenance Console Group. | ||
| adUnitSyslogGroup | 1.3.6.1.4.1.664.5.30.7.2.5 | The Unit Syslog Client Group. | ||
| adUnitTFTPGroup | 1.3.6.1.4.1.664.5.30.7.2.6 | The Unit TFTP Group. | ||
| adUnitCpuUtilGroup | 1.3.6.1.4.1.664.5.30.7.2.7 | The Unit CPU Utilization Group. | ||
| adUnitPingGroup | 1.3.6.1.4.1.664.5.30.7.2.8 | The Unit Ping Group. | ||
| adUnitTraceRtGroup | 1.3.6.1.4.1.664.5.30.7.2.9 | The Traceroute Group. | ||
| adUnitSlotGroup | 1.3.6.1.4.1.664.5.30.7.2.10 | The Unit Slot Group. | ||
| adUnitPortGroup | 1.3.6.1.4.1.664.5.30.7.2.11 | The Unit Slot Group. | ||
| adUnitsCndGroup | 1.3.6.1.4.1.664.5.30.7.2.12 | The CND Management Group. Support for this group is only required when the unit is to be managed in a CND environment. For instance, IADs which are remotely provisioned by a service provider via Total Access EMS. | ||
| adUnitsExtendedBaseGroup | 1.3.6.1.4.1.664.5.30.7.2.13 | The Extended Base Group containing functions not supported by all units. | ||
| adUnitsExtendedSNMPGroup | 1.3.6.1.4.1.664.5.30.7.2.14 | The Extended SNMP Group containing functions not supported by all units. | ||
| adConsoleModemGroup | 1.3.6.1.4.1.664.5.30.7.2.15 | The Console Modem Group containing functions not supported by all units. | ||
| adUnitsExtendedSyslogGroup | 1.3.6.1.4.1.664.5.30.7.2.16 | The Extended Syslog Group containing functions not supported by all units. | ||
| adUnitExtendedPingGroup | 1.3.6.1.4.1.664.5.30.7.2.17 | The Unit Ping Group supporting extended Ping operations (for instance, sweep & verbose modes). |
RFC description
ADTRAN private MIB defining management objects for ADTRAN unit configuration, system status, SNMP communities, and telnet access.
Start monitoring ADTRAN access routers/IADs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.