All MIBs › AETHRA-MIB
Category: DSL and Broadband
Description: Manages Aethra DSL and ISDN broadband access devices, providing line configuration and connectivity status objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is AETHRA-MIB?
AETHRA-MIB is a vendor-specific SNMP module for Aethra's DSL and ISDN broadband customer-premises/access equipment, covering xDSL line configuration and connectivity along with basic diagnostic utilities. It exposes a per-line xdslTable with link status, upstream/downstream attenuation and noise margin, and current sync rates and modulation type, plus supporting fileTransfer and ping utility objects. It's used mainly to monitor the operational health of the DSL physical layer — link up/down state, signal quality (attenuation, noise margin), and achieved sync rate — which together indicate whether a subscriber's line is degraded or healthy, and it also offers ping/file-transfer diagnostics for active connectivity testing and firmware upload. It doesn't appear to lean heavily on external MIBs beyond standard SNMP conventions, being a largely self-contained vendor MIB. It's typically deployed on Aethra DSL/ISDN modems and access routers used by broadband subscribers and small offices. Engineers can download the AETHRA-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in AETHRA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Aethra DSL/ISDN modem or broadband access router
Monitoring Examples
An ISP's NOC would poll xdslLinkStatus in xdslTable, indexed by xdslIndex, to confirm a subscriber's DSL line is synced, then check xdslUsNoiseMargin/xdslDsNoiseMargin and xdslUsAttenuation/xdslDsAttenuation to gauge line quality against provisioning thresholds. xdslUsCurrRate and xdslDsCurrRate show the actual negotiated upstream/downstream sync speed, which can be compared to the provisioned rate to spot rate-adaptation fallback. The pingParameters/ping objects let the NOC trigger an active reachability test from the CPE itself, useful when troubleshooting whether an outage is on the access line or further upstream.
What Can Be Monitored
- xDSL link status
- upstream/downstream noise margin
- upstream/downstream attenuation
- current sync rate
- modulation type
- device-initiated ping diagnostics
This MIB depends on
Related MIBs
Imported Objects
From IANAifType-MIB
| IANAifType |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress | |
| ifDescr | |
| ifIndex |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| aethra | 1.3.6.1.4.1.7745 | |||
| atosnt | 1.3.6.1.4.1.7745.5 | |||
| tools | 1.3.6.1.4.1.7745.5.1 | |||
| fileTransfer | 1.3.6.1.4.1.7745.5.1.1 | |||
| INT fileTransferProtocol | 1.3.6.1.4.1.7745.5.1.1.1 | INTEGER | read-write | Set this parameter to configure the protocol for file transfer command. The protocol file(4) reads from a local disk for download command, writes to a local disk for upload. OID: 1.3.6.1.4.1.7745.5.1.1.1 |
| STR fileTransferFileName | 1.3.6.1.4.1.7745.5.1.1.2 | DisplayString | read-write | Set this parameter to configure the name of the file to download or upload. When using HTTP protocol set full url as fileTransferFileName. OID: 1.3.6.1.4.1.7745.5.1.1.2 |
| STR fileTransferServerName | 1.3.6.1.4.1.7745.5.1.1.3 | DisplayString | read-write | Set this parameter to configure the name or IP address of remote server when using TFTP or FTP protocol. When not configured systemDefaultTftpServer or systemDefaultFtpServer is used for the respective protocols. OID: 1.3.6.1.4.1.7745.5.1.1.3 |
| INT fileTransferOption | 1.3.6.1.4.1.7745.5.1.1.4 | INTEGER | read-write | Set this parameter to configure the type of file you are downloading or uploading. When not configured firmware type is used. firmware(1) is the operating system file, boot(2) is the system boot, userconf(3) is the current system configuration file, logs(4) is the logs file and is available only for upload command, package(5) is bundle is a package that contains boot and os in a single file, localfile(6) is any file you want to download or upload in the system, welcome(7) is a text message displayed before access to system console by telnet or ssh, license(8) is a license file to enable advanced system features, certificate(9) is the custom certificate file for the security protocol system (SSL), defaultconf(10) is the custom default configuration file, bannerPre(10) is available only from version 5.6.11, is a custom pre login banner file, bannerPost(10)is available only from version 5.6.11, is a custom post login banner file. OID: 1.3.6.1.4.1.7745.5.1.1.4 |
| STR fileTransferStorageFileName | 1.3.6.1.4.1.7745.5.1.1.5 | DisplayString | read-write | Set this parameter to configure the name of the local file when using file(4) protocol. OID: 1.3.6.1.4.1.7745.5.1.1.5 |
| INT fileTransferExec | 1.3.6.1.4.1.7745.5.1.1.6 | INTEGER | read-write | Set this parameter to start download or upload. OID: 1.3.6.1.4.1.7745.5.1.1.6 |
| STR fileTransferStatus | 1.3.6.1.4.1.7745.5.1.1.7 | DisplayString | read-only | Get this parameter to read the current status of file transfer command. OID: 1.3.6.1.4.1.7745.5.1.1.7 |
| ping | 1.3.6.1.4.1.7745.5.1.2 | |||
| pingParameters | 1.3.6.1.4.1.7745.5.1.2.1 | |||
| STR pingHost | 1.3.6.1.4.1.7745.5.1.2.1.1 | DisplayString | read-write | Set this parameter to configure the host name or IP address to ping. OID: 1.3.6.1.4.1.7745.5.1.2.1.1 |
| INT pingSize | 1.3.6.1.4.1.7745.5.1.2.1.2 | INTEGER | read-write | Set this parameter to configure the size of ping packet. OID: 1.3.6.1.4.1.7745.5.1.2.1.2 |
| INT pingTries | 1.3.6.1.4.1.7745.5.1.2.1.3 | INTEGER | read-write | Set this parameter to configure the number of ping tries. OID: 1.3.6.1.4.1.7745.5.1.2.1.3 |
| INT pingTTL | 1.3.6.1.4.1.7745.5.1.2.1.4 | INTEGER | read-write | Set this parameter to configure ping TTL option. OID: 1.3.6.1.4.1.7745.5.1.2.1.4 |
| INT pingTimeOut | 1.3.6.1.4.1.7745.5.1.2.1.5 | INTEGER | read-write | Set this parameter to configure ping response timeout (sec). OID: 1.3.6.1.4.1.7745.5.1.2.1.5 |
| STR pingSource | 1.3.6.1.4.1.7745.5.1.2.1.6 | DisplayString | read-write | Set this parameter to configure the name or IP address of the ping source. OID: 1.3.6.1.4.1.7745.5.1.2.1.6 |
| INT pingStart | 1.3.6.1.4.1.7745.5.1.2.1.7 | INTEGER | read-write | Set this parameter to start ping. OID: 1.3.6.1.4.1.7745.5.1.2.1.7 |
| STR pingStatus | 1.3.6.1.4.1.7745.5.1.2.1.8 | DisplayString | read-only | Get this parameter to read the current status of ping command. OID: 1.3.6.1.4.1.7745.5.1.2.1.8 |
| pingStatistics | 1.3.6.1.4.1.7745.5.1.2.2 | |||
| INT pingTXpacket | 1.3.6.1.4.1.7745.5.1.2.2.1 | INTEGER | read-only | Get this parameter to read the number of packets transmitted. OID: 1.3.6.1.4.1.7745.5.1.2.2.1 |
| INT pingRXpacket | 1.3.6.1.4.1.7745.5.1.2.2.2 | INTEGER | read-only | Get this parameter to read the number of packets received. OID: 1.3.6.1.4.1.7745.5.1.2.2.2 |
| INT pingLOSTpacket | 1.3.6.1.4.1.7745.5.1.2.2.3 | INTEGER | read-only | Get this parameter to read the number of packets losted. OID: 1.3.6.1.4.1.7745.5.1.2.2.3 |
| INT pingMinRTT | 1.3.6.1.4.1.7745.5.1.2.2.4 | INTEGER | read-only | Get this parameter to read the minimum Round Trip Time (RTT) value. OID: 1.3.6.1.4.1.7745.5.1.2.2.4 |
| INT pingMaxRTT | 1.3.6.1.4.1.7745.5.1.2.2.5 | INTEGER | read-only | Get this parameter to read the maximum Round Trip Time (RTT) value. OID: 1.3.6.1.4.1.7745.5.1.2.2.5 |
| INT pingAvgRTT | 1.3.6.1.4.1.7745.5.1.2.2.6 | INTEGER | read-only | Get this parameter to read the average Round Trip Time (RTT) value. OID: 1.3.6.1.4.1.7745.5.1.2.2.6 |
| system | 1.3.6.1.4.1.7745.5.2 | |||
| INT systemLoglevel | 1.3.6.1.4.1.7745.5.2.1 | INTEGER | read-write | Set this parameter to configure the log level of the node system. OID: 1.3.6.1.4.1.7745.5.2.1 |
| STR systemDescription | 1.3.6.1.4.1.7745.5.2.2 | DisplayString | read-write | Set this parameter to configure system description. OID: 1.3.6.1.4.1.7745.5.2.2 |
| STR systemName | 1.3.6.1.4.1.7745.5.2.3 | DisplayString | read-write | Set this parameter to configure system name, it's also used as network hostname. OID: 1.3.6.1.4.1.7745.5.2.3 |
| STR systemLocalDomain | 1.3.6.1.4.1.7745.5.2.4 | DisplayString | read-write | Set this parameter to configure system local domain, it's also used as network workgroup. OID: 1.3.6.1.4.1.7745.5.2.4 |
| STR systemDefaultTftpServer | 1.3.6.1.4.1.7745.5.2.5 | DisplayString | read-write | Set this parameter to configure the name or IP address for the default remote TFTP server. OID: 1.3.6.1.4.1.7745.5.2.5 |
| IP systemTftpLocalAdd | 1.3.6.1.4.1.7745.5.2.6 | IpAddress | read-write | Set this parameter to configure the name or the local IP address used by the TFTP client. OID: 1.3.6.1.4.1.7745.5.2.6 |
| STR systemDefaultFtpServer | 1.3.6.1.4.1.7745.5.2.7 | DisplayString | read-write | Set this parameter to configure the name or IP address and port for the default remote FTP server. OID: 1.3.6.1.4.1.7745.5.2.7 |
| IP systemFtpLocalAdd | 1.3.6.1.4.1.7745.5.2.8 | IpAddress | read-write | Set this parameter to configure the name or the local IP address used by the FTP client. OID: 1.3.6.1.4.1.7745.5.2.8 |
| STR systemFtpUsername | 1.3.6.1.4.1.7745.5.2.9 | DisplayString | read-write | Set this parameter to configure the username for the default remote FTP server. OID: 1.3.6.1.4.1.7745.5.2.9 |
| STR systemFtpPassword | 1.3.6.1.4.1.7745.5.2.10 | DisplayString | read-write | Set this parameter to configure the password for the default remote FTP server. OID: 1.3.6.1.4.1.7745.5.2.10 |
| STR systemAAAProfile | 1.3.6.1.4.1.7745.5.2.11 | DisplayString | read-write | Set this parameter to configure the AAA profile used by the system. OID: 1.3.6.1.4.1.7745.5.2.11 |
| INT systemAAALogTimeout | 1.3.6.1.4.1.7745.5.2.12 | INTEGER | read-write | Set this parameter to configure the AAA login timeout. OID: 1.3.6.1.4.1.7745.5.2.12 |
| INT systemBackupAuth | 1.3.6.1.4.1.7745.5.2.13 | INTEGER | read-write | Set this parameter to enable the backup authentication system. OID: 1.3.6.1.4.1.7745.5.2.13 |
| INT systemScrollLine | 1.3.6.1.4.1.7745.5.2.14 | INTEGER | read-write | Set this parameter to enable the system scroll line. OID: 1.3.6.1.4.1.7745.5.2.14 |
| INT systemKernelLogs | 1.3.6.1.4.1.7745.5.2.15 | INTEGER | read-write | Set this parameter to enable the system kernel logs OID: 1.3.6.1.4.1.7745.5.2.15 |
| INT systemCryptedPassword | 1.3.6.1.4.1.7745.5.2.16 | INTEGER | read-write | Set this parameter to enable the system crypted password. OID: 1.3.6.1.4.1.7745.5.2.16 |
| INT systemSave | 1.3.6.1.4.1.7745.5.2.17 | INTEGER | read-write | Set this parameter to save current configuration. OID: 1.3.6.1.4.1.7745.5.2.17 |
| systemRestart | 1.3.6.1.4.1.7745.5.2.18 | |||
| INT restartOption | 1.3.6.1.4.1.7745.5.2.18.1 | INTEGER | read-write | Set this parameter to choose restart command option. saveConf(0) saving configuration changes before restart the system, notSaveConf(1) restart the system without saving configuration changes, restoreDefaultConf(2) restart the system with the default configuration, restoreFactoryDefault(3) available only from version 5.6.14, restart the system with the factory default. OID: 1.3.6.1.4.1.7745.5.2.18.1 |
| INT restartDelay | 1.3.6.1.4.1.7745.5.2.18.2 | INTEGER | read-write | Set this parameter to configure restart timeout (sec). OID: 1.3.6.1.4.1.7745.5.2.18.2 |
| INT restartExec | 1.3.6.1.4.1.7745.5.2.18.3 | INTEGER | read-write | Set this parameter to restart the system. OID: 1.3.6.1.4.1.7745.5.2.18.3 |
| STR restartStatus | 1.3.6.1.4.1.7745.5.2.18.4 | DisplayString | read-only | Get this parameter to read the current status of restart command. OID: OID: 1.3.6.1.4.1.7745.5.2.18.4 |
| performance | 1.3.6.1.4.1.7745.5.2.19 | |||
| INT performanceCpuAvg1min | 1.3.6.1.4.1.7745.5.2.19.1 | INTEGER | read-only | Get this parameter to read the CPU average utilization in 1 minute (in %). OID: 1.3.6.1.4.1.7745.5.2.19.1 |
| INT performanceCpuAvg5min | 1.3.6.1.4.1.7745.5.2.19.2 | INTEGER | read-only | Get this parameter to read the CPU average utilization in 5 minute (in %). OID: 1.3.6.1.4.1.7745.5.2.19.2 |
| INT performanceCpuAvg15min | 1.3.6.1.4.1.7745.5.2.19.3 | INTEGER | read-only | Get this parameter to read the CPU average utilization in 15 minute (in %). OID: 1.3.6.1.4.1.7745.5.2.19.3 |
| INT performanceDynMemLoad | 1.3.6.1.4.1.7745.5.2.19.4 | INTEGER | read-only | Get this parameter to read the usage of dynamic memory (in %). OID: 1.3.6.1.4.1.7745.5.2.19.4 |
| INT performanceDynMemTotal | 1.3.6.1.4.1.7745.5.2.19.5 | INTEGER | read-only | Get this parameter to read the total dynamic memory (in KBytes). OID: 1.3.6.1.4.1.7745.5.2.19.5 |
| INT performanceDynMemFree | 1.3.6.1.4.1.7745.5.2.19.6 | INTEGER | read-only | Get this parameter to read the free dynamic memory (in KBytes). OID: 1.3.6.1.4.1.7745.5.2.19.6 |
| STR systemDefaultScpServer | 1.3.6.1.4.1.7745.5.2.20 | DisplayString | read-write | Set this parameter to configure the name or IP address and port for the default remote SCP server. OID: 1.3.6.1.4.1.7745.5.2.20 |
| STR systemScpUsername | 1.3.6.1.4.1.7745.5.2.21 | DisplayString | read-write | Set this parameter to configure the username for the default remote SCP server. OID: 1.3.6.1.4.1.7745.5.2.21 |
| STR systemScpPassword | 1.3.6.1.4.1.7745.5.2.22 | DisplayString | read-write | Set this parameter to configure the password for the default remote SCP server. OID: 1.3.6.1.4.1.7745.5.2.22 |
| INT systemConsoleEnable | 1.3.6.1.4.1.7745.5.2.23 | INTEGER | read-write | Set this parameter to enable or disable serial console. OID: 1.3.6.1.4.1.7745.5.2.23 |
| INT systemLogMsgRate | 1.3.6.1.4.1.7745.5.2.24 | INTEGER | read-write | Set this parameter to configure the maximum number of log messages per minute. A value set to 0 (zero) is equivalent to unlimited. OID: 1.3.6.1.4.1.7745.5.2.24 |
| dsl | 1.3.6.1.4.1.7745.5.3 | |||
| xdsl | 1.3.6.1.4.1.7745.5.3.1 | |||
| xdslTable | 1.3.6.1.4.1.7745.5.3.1.1 | not-accessible | This is a table showing the list of xdsl interface entries. OID: 1.3.6.1.4.1.7745.5.3.1.1 | |
| xdslEntry | 1.3.6.1.4.1.7745.5.3.1.1.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.3.1.1.1 | |
| INT xdslIndex | 1.3.6.1.4.1.7745.5.3.1.1.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.1 |
| STR xdslLinkStatus | 1.3.6.1.4.1.7745.5.3.1.1.1.2 | DisplayString | read-only | Get this parameter to read the link status. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.2 |
| STR xdslTc | 1.3.6.1.4.1.7745.5.3.1.1.1.3 | DisplayString | read-only | Get this parameter to read link transmission convergence. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.3 |
| INT xdslUsAttenuation | 1.3.6.1.4.1.7745.5.3.1.1.1.4 | INTEGER | read-only | Get this parameter to read link upstream attenuation (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.4 |
| INT xdslDsAttenuation | 1.3.6.1.4.1.7745.5.3.1.1.1.5 | INTEGER | read-only | Get this parameter to read link downstream attenuation (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.5 |
| INT xdslUsNoiseMargin | 1.3.6.1.4.1.7745.5.3.1.1.1.6 | INTEGER | read-only | Get this parameter to read link upstream noise margin (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.6 |
| INT xdslDsNoiseMargin | 1.3.6.1.4.1.7745.5.3.1.1.1.7 | INTEGER | read-only | Get this parameter to read link downstream noise margin (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.7 |
| INT xdslUsCurrRate | 1.3.6.1.4.1.7745.5.3.1.1.1.8 | INTEGER | read-only | Get this parameter to read link upstream current rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.8 |
| INT xdslDsCurrRate | 1.3.6.1.4.1.7745.5.3.1.1.1.9 | INTEGER | read-only | Get this parameter to read link downstream current rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.9 |
| STR xdslModulationType | 1.3.6.1.4.1.7745.5.3.1.1.1.10 | DisplayString | read-only | Get this parameter to read link modulation type. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.10 |
| INT xdslUsMaxTheorRate | 1.3.6.1.4.1.7745.5.3.1.1.1.11 | INTEGER | read-only | Get this parameter to read link upstream attainable max rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.11 |
| INT xdslDsMaxTheorRate | 1.3.6.1.4.1.7745.5.3.1.1.1.12 | INTEGER | read-only | Get this parameter to read link downstream attainable max rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.1.1.1.12 |
| INT xdslUsTotBytes | 1.3.6.1.4.1.7745.5.3.1.1.1.13 | INTEGER | read-only | Get this parameter to read link upstream total bytes. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.13 |
| INT xdslDsTotBytes | 1.3.6.1.4.1.7745.5.3.1.1.1.14 | INTEGER | read-only | Get this parameter to read link downstream total bytes. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.14 |
| INT xdslNeTotCrcErr | 1.3.6.1.4.1.7745.5.3.1.1.1.15 | INTEGER | read-only | Get this parameter to read link near-end total CRC errors. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.15 |
| INT xdslNeShowtimeCrcErr | 1.3.6.1.4.1.7745.5.3.1.1.1.16 | INTEGER | read-only | Get this parameter to read link near-end last showtime CRC errors. OID: 1.3.6.1.4.1.7745.5.3.1.1.1.16 |
| shdsl | 1.3.6.1.4.1.7745.5.3.2 | |||
| shdslTable | 1.3.6.1.4.1.7745.5.3.2.1 | not-accessible | This is a table showing the list of shdsl physical interface entries. OID: 1.3.6.1.4.1.7745.5.3.2.1 | |
| shdslEntry | 1.3.6.1.4.1.7745.5.3.2.1.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.3.2.1.1 | |
| INT shdslIndex | 1.3.6.1.4.1.7745.5.3.2.1.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.1 |
| STR shdslPhyStatus | 1.3.6.1.4.1.7745.5.3.2.1.1.2 | DisplayString | read-only | Get this parameter to read physical status. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.2 |
| STR shdslTc | 1.3.6.1.4.1.7745.5.3.2.1.1.3 | DisplayString | read-only | Get this parameter to read physical transmission convergence. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.3 |
| INT shdslUsAttenuation | 1.3.6.1.4.1.7745.5.3.2.1.1.4 | INTEGER | read-only | Get this parameter to read physical upstream attenuation (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.4 |
| INT shdslDsAttenuation | 1.3.6.1.4.1.7745.5.3.2.1.1.5 | INTEGER | read-only | Get this parameter to read physical downstream attenuation (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.5 |
| INT shdslUsNoiseMargin | 1.3.6.1.4.1.7745.5.3.2.1.1.6 | INTEGER | read-only | Get this parameter to read physical upstream noise margin (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.6 |
| INT shdslDsNoiseMargin | 1.3.6.1.4.1.7745.5.3.2.1.1.7 | INTEGER | read-only | Get this parameter to read physical downstream noise margin (0.1 dB steps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.7 |
| INT shdslUsCurrRate | 1.3.6.1.4.1.7745.5.3.2.1.1.8 | INTEGER | read-only | Get this parameter to read physical upstream current rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.8 |
| INT shdslDsCurrRate | 1.3.6.1.4.1.7745.5.3.2.1.1.9 | INTEGER | read-only | Get this parameter to read physical downstream current rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.9 |
| STR shdslModulationType | 1.3.6.1.4.1.7745.5.3.2.1.1.10 | DisplayString | read-only | Get this parameter to read physical modulation type. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.10 |
| INT shdslUsMaxTheorRate | 1.3.6.1.4.1.7745.5.3.2.1.1.11 | INTEGER | read-only | Get this parameter to read physical upstream attainable max rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.11 |
| INT shdslDsMaxTheorRate | 1.3.6.1.4.1.7745.5.3.2.1.1.12 | INTEGER | read-only | Get this parameter to read physical downstream attainable max rate (in Kbps). OID: 1.3.6.1.4.1.7745.5.3.2.1.1.12 |
| INT shdslUsTotBytes | 1.3.6.1.4.1.7745.5.3.2.1.1.13 | INTEGER | read-only | Get this parameter to read physical upstream total bytes. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.13 |
| INT shdslDsTotBytes | 1.3.6.1.4.1.7745.5.3.2.1.1.14 | INTEGER | read-only | Get this parameter to read physical downstream total bytes. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.14 |
| INT shdslNeTotCrcErr | 1.3.6.1.4.1.7745.5.3.2.1.1.15 | INTEGER | read-only | Get this parameter to read physical near-end total CRC errors. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.15 |
| INT shdslNeShowtimeCrcErr | 1.3.6.1.4.1.7745.5.3.2.1.1.16 | INTEGER | read-only | Get this parameter to read physical near-end last showtime CRC errors. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.16 |
| INT shdslUsPower | 1.3.6.1.4.1.7745.5.3.2.1.1.17 | INTEGER | read-only | Get this parameter to read physical Us Power. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.17 |
| INT shdslDsPower | 1.3.6.1.4.1.7745.5.3.2.1.1.18 | INTEGER | read-only | Get this parameter to read physical Ds Power. OID: 1.3.6.1.4.1.7745.5.3.2.1.1.18 |
| voip | 1.3.6.1.4.1.7745.5.4 | |||
| trunk | 1.3.6.1.4.1.7745.5.4.1 | |||
| trunkTable | 1.3.6.1.4.1.7745.5.4.1.1 | not-accessible | This is a table showing the list of configured voip SIP trunk. OID: 1.3.6.1.4.1.7745.5.4.1.1 | |
| trunkEntry | 1.3.6.1.4.1.7745.5.4.1.1.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.1.1.1 | |
| INT trunkIndex | 1.3.6.1.4.1.7745.5.4.1.1.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.1 |
| STR trunkName | 1.3.6.1.4.1.7745.5.4.1.1.1.2 | DisplayString | read-only | Get this parameter to read trunk name. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.2 |
| STR trunkType | 1.3.6.1.4.1.7745.5.4.1.1.1.3 | DisplayString | read-only | Get this parameter to read trunk type. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.3 |
| INT trunkEnable | 1.3.6.1.4.1.7745.5.4.1.1.1.4 | INTEGER | read-write | Get this parameter to read trunk registration enable. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.4 |
| STR trunkDescription | 1.3.6.1.4.1.7745.5.4.1.1.1.5 | DisplayString | read-only | Get this parameter to read trunk description. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.5 |
| STR trunkUserName | 1.3.6.1.4.1.7745.5.4.1.1.1.6 | DisplayString | read-only | Get this parameter to read trunk username. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.6 |
| STR trunkRegHost | 1.3.6.1.4.1.7745.5.4.1.1.1.7 | DisplayString | read-only | Get this parameter to read trunk registar host. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.7 |
| STR trunkProxyHost | 1.3.6.1.4.1.7745.5.4.1.1.1.8 | DisplayString | read-only | Get this parameter to read trunk proxy host. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.8 |
| STR trunkIfcStatus | 1.3.6.1.4.1.7745.5.4.1.1.1.9 | DisplayString | read-only | Get this parameter to read trunk interface status. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.9 |
| STR trunkRegStatus | 1.3.6.1.4.1.7745.5.4.1.1.1.10 | DisplayString | read-only | Get this parameter to read trunk registration status. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.10 |
| STR trunkMsgWait | 1.3.6.1.4.1.7745.5.4.1.1.1.11 | DisplayString | read-only | Get this parameter to read trunk message wait status. OID: 1.3.6.1.4.1.7745.5.4.1.1.1.11 |
| trunkIsdnTable | 1.3.6.1.4.1.7745.5.4.1.2 | not-accessible | This is a table showing the list of configured voip ISDN trunk. OID: 1.3.6.1.4.1.7745.5.4.1.2 | |
| trunkIsdnEntry | 1.3.6.1.4.1.7745.5.4.1.2.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.1.2.1 | |
| INT trunkIsdnIndex | 1.3.6.1.4.1.7745.5.4.1.2.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.1 |
| STR trunkIsdnName | 1.3.6.1.4.1.7745.5.4.1.2.1.2 | DisplayString | read-only | Get this parameter to read trunk name. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.2 |
| STR trunkIsdnType | 1.3.6.1.4.1.7745.5.4.1.2.1.3 | DisplayString | read-only | Get this parameter to read trunk type. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.3 |
| INT trunkIsdnEnable | 1.3.6.1.4.1.7745.5.4.1.2.1.4 | INTEGER | read-write | Get this parameter to read trunk enable configuration. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.4 |
| STR trunkIsdnDescription | 1.3.6.1.4.1.7745.5.4.1.2.1.5 | DisplayString | read-only | Get this parameter to read trunk description. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.5 |
| STR trunkIsdnB1Status | 1.3.6.1.4.1.7745.5.4.1.2.1.6 | DisplayString | read-only | Get this parameter to read trunk B1 status. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.6 |
| STR trunkIsdnB2Status | 1.3.6.1.4.1.7745.5.4.1.2.1.7 | DisplayString | read-only | Get this parameter to read trunk B2 status. OID: 1.3.6.1.4.1.7745.5.4.1.2.1.7 |
| trunkFxoTable | 1.3.6.1.4.1.7745.5.4.1.3 | not-accessible | This is a table showing the list of configured voip FXO trunk. OID: 1.3.6.1.4.1.7745.5.4.1.3 | |
| trunkFxoEntry | 1.3.6.1.4.1.7745.5.4.1.3.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.1.3.1 | |
| INT trunkFxoIndex | 1.3.6.1.4.1.7745.5.4.1.3.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.1 |
| STR trunkFxoName | 1.3.6.1.4.1.7745.5.4.1.3.1.2 | DisplayString | read-only | Get this parameter to read trunk name. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.2 |
| STR trunkFxoType | 1.3.6.1.4.1.7745.5.4.1.3.1.3 | DisplayString | read-only | Get this parameter to read trunk type. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.3 |
| INT trunkFxoEnable | 1.3.6.1.4.1.7745.5.4.1.3.1.4 | INTEGER | read-write | Get this parameter to read trunk enable configuration. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.4 |
| STR trunkFxoDescription | 1.3.6.1.4.1.7745.5.4.1.3.1.5 | DisplayString | read-only | Get this parameter to read trunk description. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.5 |
| STR trunkFxoStatus | 1.3.6.1.4.1.7745.5.4.1.3.1.6 | DisplayString | read-only | Get this parameter to read trunk status. OID: 1.3.6.1.4.1.7745.5.4.1.3.1.6 |
| userTerminal | 1.3.6.1.4.1.7745.5.4.2 | |||
| usTermPotsTable | 1.3.6.1.4.1.7745.5.4.2.1 | not-accessible | This is a table showing the list of configured voip POTS user terminal. OID: 1.3.6.1.4.1.7745.5.4.2.1 | |
| usTermPotsEntry | 1.3.6.1.4.1.7745.5.4.2.1.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.2.1.1 | |
| INT usTermPotsIndex | 1.3.6.1.4.1.7745.5.4.2.1.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.2.1.1.1 |
| INT usTermPotsEnable | 1.3.6.1.4.1.7745.5.4.2.1.1.2 | INTEGER | read-write | Get this parameter to read user terminal enable configuration. OID: 1.3.6.1.4.1.7745.5.4.2.1.1.2 |
| STR usTermPotsDescription | 1.3.6.1.4.1.7745.5.4.2.1.1.3 | DisplayString | read-only | Get this parameter to read user terminal description. OID: 1.3.6.1.4.1.7745.5.4.2.1.1.3 |
| STR usTermPotsStatus | 1.3.6.1.4.1.7745.5.4.2.1.1.4 | DisplayString | read-only | Get this parameter to read user terminal status. OID: 1.3.6.1.4.1.7745.5.4.2.1.1.4 |
| STR usTermPotsDspSlic | 1.3.6.1.4.1.7745.5.4.2.1.1.5 | DisplayString | read-only | Get this parameter to read user terminal DSP Slic. OID: 1.3.6.1.4.1.7745.5.4.2.1.1.5 |
| usTermISDNTable | 1.3.6.1.4.1.7745.5.4.2.2 | not-accessible | This is a table showing the list of configured voip ISDN user terminal. OID: 1.3.6.1.4.1.7745.5.4.2.2 | |
| usTermISDNEntry | 1.3.6.1.4.1.7745.5.4.2.2.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.2.2.1 | |
| INT usTermISDNIndex | 1.3.6.1.4.1.7745.5.4.2.2.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.2.2.1.1 |
| INT usTermISDNEnable | 1.3.6.1.4.1.7745.5.4.2.2.1.2 | INTEGER | read-write | Get this parameter to read user terminal enable configuration. OID: 1.3.6.1.4.1.7745.5.4.2.2.1.2 |
| STR usTermISDNDescription | 1.3.6.1.4.1.7745.5.4.2.2.1.3 | DisplayString | read-only | Get this parameter to read user terminal description. OID: 1.3.6.1.4.1.7745.5.4.2.2.1.3 |
| STR usTermIsdnStatusB1 | 1.3.6.1.4.1.7745.5.4.2.2.1.4 | DisplayString | read-only | Get this parameter to read user terminal B1 status. OID: 1.3.6.1.4.1.7745.5.4.2.2.1.4 |
| STR usTermIsdnStatusB2 | 1.3.6.1.4.1.7745.5.4.2.2.1.5 | DisplayString | read-only | Get this parameter to read user terminal B2 status. OID: 1.3.6.1.4.1.7745.5.4.2.2.1.5 |
| usTermDectTable | 1.3.6.1.4.1.7745.5.4.2.3 | not-accessible | This is a table showing the list of configured voip DECT user terminal. OID: 1.3.6.1.4.1.7745.5.4.2.3 | |
| usTermDectEntry | 1.3.6.1.4.1.7745.5.4.2.3.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.4.2.3.1 | |
| INT usTermDectIndex | 1.3.6.1.4.1.7745.5.4.2.3.1.1 | INTEGER | read-only | Get this parameter to read the index of the row. OID: 1.3.6.1.4.1.7745.5.4.2.3.1.1 |
| INT usTermDectEnable | 1.3.6.1.4.1.7745.5.4.2.3.1.2 | INTEGER | read-write | Get this parameter to read user terminal enable configuration. OID: 1.3.6.1.4.1.7745.5.4.2.3.1.2 |
| STR usTermDectDescription | 1.3.6.1.4.1.7745.5.4.2.3.1.3 | DisplayString | read-only | Get this parameter to read user terminal description. OID: 1.3.6.1.4.1.7745.5.4.2.3.1.3 |
| STR usTermDectStatus | 1.3.6.1.4.1.7745.5.4.2.3.1.4 | DisplayString | read-only | Get this parameter to read user terminal status. OID: 1.3.6.1.4.1.7745.5.4.2.3.1.4 |
| STR usTermDectDspSlic | 1.3.6.1.4.1.7745.5.4.2.3.1.5 | DisplayString | read-only | Get this parameter to read user terminal DSP Slic. OID: 1.3.6.1.4.1.7745.5.4.2.3.1.5 |
| INT voipMaxConnection | 1.3.6.1.4.1.7745.5.4.3 | INTEGER | read-write | Set this parameter to configure global voip max connections. OID: 1.3.6.1.4.1.7745.5.4.3 |
| traps | 1.3.6.1.4.1.7745.5.5 | |||
| NTF genericTrap | 1.3.6.1.4.1.7745.5.5.1 | This trap is used to send generic string alarm messages to SNMP manager, when a particular condition occurs. OID: 1.3.6.1.4.1.7745.5.5.1 | ||
| STR genericError | 1.3.6.1.4.1.7745.5.5.2 | DisplayString | read-only | Describe a generic error for generic trap. OID: 1.3.6.1.4.1.7745.5.5.2 |
| NTF interfaceUp | 1.3.6.1.4.1.7745.5.5.3 | This trap is sent when a physical interface go up. OID: 1.3.6.1.4.1.7745.5.5.3 | ||
| NTF interfaceDown | 1.3.6.1.4.1.7745.5.5.4 | This trap is sent when a physical interface go down. OID: 1.3.6.1.4.1.7745.5.5.4 | ||
| NTF trunkRegistered | 1.3.6.1.4.1.7745.5.5.5 | This trap is sent when a voip SIP Trunk registered. OID: 1.3.6.1.4.1.7745.5.5.5 | ||
| NTF trunkUnregistered | 1.3.6.1.4.1.7745.5.5.6 | This trap is sent when a voip SIP Trunk unregistered. OID: 1.3.6.1.4.1.7745.5.5.6 | ||
| mgmtAccesses | 1.3.6.1.4.1.7745.5.5.7 | |||
| STR mgmtUser | 1.3.6.1.4.1.7745.5.5.7.1 | DisplayString | read-only | A textual string containing user name. OID: 1.3.6.1.4.1.7745.5.5.7.1 |
| STR mgmtPrivilege | 1.3.6.1.4.1.7745.5.5.7.2 | DisplayString | read-only | A textual string containing user privilege. OID: 1.3.6.1.4.1.7745.5.5.7.2 |
| STR mgmtTime | 1.3.6.1.4.1.7745.5.5.7.3 | DisplayString | read-only | A textual string containing time and date of event. OID: 1.3.6.1.4.1.7745.5.5.7.3 |
| INT mgmtType | 1.3.6.1.4.1.7745.5.5.7.4 | INTEGER | read-only | A textual string containing user access type. OID: 1.3.6.1.4.1.7745.5.5.7.4 |
| STR mgmtAddress | 1.3.6.1.4.1.7745.5.5.7.5 | DisplayString | read-only | A textual string containing ip for remote access type. OID: 1.3.6.1.4.1.7745.5.5.7.5 |
| NTF mgmtLogin | 1.3.6.1.4.1.7745.5.5.7.6 | This trap is sent when a user login in the system console. OID: 1.3.6.1.4.1.7745.5.5.7.6 | ||
| NTF mgmtLogout | 1.3.6.1.4.1.7745.5.5.7.7 | This trap is sent when a user logout from the system console. OID: 1.3.6.1.4.1.7745.5.5.7.7 | ||
| NTF mgmtChange | 1.3.6.1.4.1.7745.5.5.7.8 | This trap is sent when a logged user change param in the system console. OID: 1.3.6.1.4.1.7745.5.5.7.8 | ||
| ifc | 1.3.6.1.4.1.7745.5.6 | |||
| ifcTable | 1.3.6.1.4.1.7745.5.6.1 | not-accessible | This is a table showing the list of interface entries. The number of entries is given by the value of mib-2 ifNumber. The indexes for the rows are equivalent to mib-2 ifIndex. OID: 1.3.6.1.4.1.7745.5.6.1 | |
| ifcEntry | 1.3.6.1.4.1.7745.5.6.1.1 | not-accessible | OID: 1.3.6.1.4.1.7745.5.6.1.1 | |
| STR ifcName | 1.3.6.1.4.1.7745.5.6.1.1.1 | DisplayString | read-only | Get this parameter to read interface name. OID: 1.3.6.1.4.1.7745.5.6.1.1.1 |
| STR ifcDescr | 1.3.6.1.4.1.7745.5.6.1.1.2 | DisplayString | read-only | Get this parameter to read interface description. OID: 1.3.6.1.4.1.7745.5.6.1.1.2 |
| IAN ifcType | 1.3.6.1.4.1.7745.5.6.1.1.3 | IANAifType | read-only | Get this parameter to read interface type. The types refer to those assigned by the Internet Assigned Numbers Authority (IANA). OID: 1.3.6.1.4.1.7745.5.6.1.1.3 |
| PHY ifcPhysAddress | 1.3.6.1.4.1.7745.5.6.1.1.4 | PhysAddress | read-only | Get this parameter to read interface physical address (mac address). OID: 1.3.6.1.4.1.7745.5.6.1.1.4 |
| INT ifcMtu | 1.3.6.1.4.1.7745.5.6.1.1.5 | INTEGER | read-only | Get this parameter to read interface MTU, the size of the largest datagram which can be sent/received on the interface, specified in octets. OID: 1.3.6.1.4.1.7745.5.6.1.1.5 |
| GAU ifcSpeed | 1.3.6.1.4.1.7745.5.6.1.1.6 | Gauge | read-only | Get this parameter to read interface speed, an estimate of the interface's current bandwidth in bits per second. OID: 1.3.6.1.4.1.7745.5.6.1.1.6 |
| CTR ifcRxRate | 1.3.6.1.4.1.7745.5.6.1.1.7 | Counter | read-only | Get this parameter to read the current and effective RX rate in bit per second. OID: 1.3.6.1.4.1.7745.5.6.1.1.7 |
| CTR ifcTxRate | 1.3.6.1.4.1.7745.5.6.1.1.8 | Counter | read-only | Get this parameter to read the current and effective TX rate in bit per second. OID: 1.3.6.1.4.1.7745.5.6.1.1.8 |
RFC description
Aethra Telecommunications enterprise MIB supporting DSL, VoIP, system, and interface management.
Start monitoring Aethra DSL/ISDN modems and routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.