AC-MEDIA-MIB

All MIBs › AC-MEDIA-MIB

Organization: AudioCodes Ltd

Last Updated: 2010-01-17

Description: AudioCodes MIB for DSP load template selection, codec capacity, and DSP module configuration on AudioCodes VoIP media gateways

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AC-MEDIA-MIB?

AC-MEDIA-MIB is a vendor MIB from AudioCodes used to manage DSP (digital signal processor) resources on AudioCodes VoIP media gateways, covering DSP load template selection, codec capacity allocation, and DSP module configuration. It exposes configuration data determining which voice codecs and channel-density templates are loaded onto the gateway's DSP hardware, directly affecting how many simultaneous calls the device can handle. This MIB is used to monitor and manage a critical piece of the gateway's hardware/software capacity: verifying the correct DSP template is loaded ensures the expected codec set and channel capacity are active, and mismatches here are a common cause of unexpected call-capacity shortfalls or codec negotiation failures. It has no stated dependency on other standard MIBs beyond AudioCodes' own MIB family. It is deployed on AudioCodes VoIP gateways and session border controllers where DSP resource allocation must match expected traffic and codec mix. Network engineers evaluating or troubleshooting this functionality can download the AC-MEDIA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AC-MEDIA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

AudioCodes VoIP media gateway

Monitoring Examples

No concrete sample objects were supplied for this module, so specific object names cannot be grounded; in general an administrator would check the active DSP load template and codec capacity settings to confirm the gateway is provisioned for the expected codec mix and call volume, but naming exact objects here would be speculative.

Imported Objects

From AUDIOCODES-TYPES-MIB

acBoardMibs	OBJECT-IDENTITY
acGeneric	OBJECT-IDENTITY
acProducts	OBJECT-IDENTITY
acRegistrations	OBJECT-IDENTITY
audioCodes	OBJECT-IDENTITY

From RFC1155-SMI

IpAddress

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TAddress
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
acMedia	1.3.6.1.4.1.5003.9.10.4
acMediaConfiguration	1.3.6.1.4.1.5003.9.10.4.1
acMediaDSPConfig	1.3.6.1.4.1.5003.9.10.4.1.1
U32 acMediaDSPConfigVersionTemplateNumber	1.3.6.1.4.1.5003.9.10.4.1.1.1	Unsigned32	read-write	Selects the DSP load number. Each load has a different coder list, a different channel capacity and different features supported. Range = 0 to 255. Access: Offline. AC INI-Param: DSPVERSIONTEMPLATENUMBER
acMediaDspTable	1.3.6.1.4.1.5003.9.10.4.1.1.21		not-accessible
acMediaDspEntry	1.3.6.1.4.1.5003.9.10.4.1.1.21.1		not-accessible
U32 acMediaDspIndex	1.3.6.1.4.1.5003.9.10.4.1.1.21.1.1	Unsigned32	not-accessible	Entry number in the table. AC INI-Param: DspTemplates_Index
ROW acMediaDspRowStatus	1.3.6.1.4.1.5003.9.10.4.1.1.21.1.2	RowStatus	read-create	ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
U32 acMediaDspTemplateNumber	1.3.6.1.4.1.5003.9.10.4.1.1.21.1.3	Unsigned32	read-create	DSP template number. Access: Offline. AC INI-Param: DspTemplates_DspTemplateNumber
U32 acMediaDspResourcesPercentage	1.3.6.1.4.1.5003.9.10.4.1.1.21.1.4	Unsigned32	read-create	Percentage use for the specified template. Access: Offline. AC INI-Param: DspTemplates_DspResourcesPercentage
acMediaVoiceConfig	1.3.6.1.4.1.5003.9.10.4.1.2
acVoice	1.3.6.1.4.1.5003.9.10.4.1.2.1
INT acVoicePayloadFormat	1.3.6.1.4.1.5003.9.10.4.1.2.1.1	INTEGER	read-write	Sets the voice payload format. Choose either 0 = RTP or 1 = ATM (which enables working with vendors that use G.726 ATM Payload Format over RTP. Uses the enum acTVoicePayloadFormat. 0 = VoicePayloadFormatRTP 1 = VoicePayloadFormatATM 2 = VoicePAyloadFormatIllegal. Access: Online. AC INI-Param: VOICEPAYLOADFORMAT
I32 acVoiceVolume	1.3.6.1.4.1.5003.9.10.4.1.2.1.2	Integer32	read-write	Defines the voice output gain control. Range: -32 dB to +31 dB in 1 dB steps -32 = mute Default = 0 = No Gain. Access: Online. AC INI-Param: VOICEVOLUME
I32 acVoiceInputGain	1.3.6.1.4.1.5003.9.10.4.1.2.1.3	Integer32	read-write	Defines the PCM input gain. Range = -32 dB to +31 dB in 1 dB steps. Default = No Gain. Access: Online. AC INI-Param: INPUTGAIN
INT acVoiceTestMode	1.3.6.1.4.1.5003.9.10.4.1.2.1.4	INTEGER	read-write	Defines the type of testing mode applied: 0 = Coder Loopback performs an encoder/decoder loopback inside the DSP device 1 = PCM Loopback loops back an incoming PCM to the outgoing PCM. 2 = ToneInjection generates a 1000 Hz tone to the outgoing PCM 3 = NoLoopback sets the channel to work in normal mode. Access: Online. AC INI-Param: TESTMODE
INT acVoiceTTYTransportType	1.3.6.1.4.1.5003.9.10.4.1.2.1.5	INTEGER	read-write	Defines the transferring method of TTY signals during a call 0 = Disable 1= Bypass 2 = Relay . Access: Online. AC INI-Param: TTYTRANSPORTTYPE
INT acVoiceEnableMediaSecurity	1.3.6.1.4.1.5003.9.10.4.1.2.1.6	INTEGER	read-write	Enables or disables Media Security protocol (SRTP) . Enabling this parameter might reduce the board channel capacity. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLEMEDIASECURITY
acVoiceCoderRate	1.3.6.1.4.1.5003.9.10.4.1.2.1.20
INT acVoiceCoderRateEVRC	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.1	INTEGER	read-write	This parameter is used to configure the EVRC coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 4 kbps 3 = 8 kbps. Access: Online. AC INI-Param: EVRCRate
INT acVoiceCoderRateQCELP8	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.2	INTEGER	read-write	This parameter is used to configure the QCELP8 coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 2 kbps 3 = 4 kbps 4 = 8 kbps. Access: Online. AC INI-Param: QCELP8Rate
INT acVoiceCoderRateQCELP13	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.3	INTEGER	read-write	This parameter is used to configure the QCELP13 coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 3 kbps 3 = 7 kbps 4 = 13 kbps . Access: Online. AC INI-Param: QCELP13Rate
INT acVoiceCoderRateG729EVMaxBitRate	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.4	INTEGER	read-write	Determines the maximum generation bitrate for all participants in a session using G729EV coder. This parameter is defined per session and is equal for all the parties. The initial generation bit rate is the minimum between the MaxBitRate and the MBS values. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVMaxBitRate
INT acVoiceCoderRateG729EVLocalMBS	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.5	INTEGER	read-write	Determines the maximal bitrate, which may be used by the G729EV coder at a specific channel. This parameter is defined per channel and may vary between the parties. The initial generation bit rate is the minimum between the MaxBitRate and the MBS values. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVLocalMBS
INT acVoiceCoderRateG729EVReceiveMBS	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.6	INTEGER	read-write	Determines the value of the MBS field of the G729EV frames to be sent to the other party. This parameter reflects the maximum bit rate, which the local G729EV supports as a receiver. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVReceiveMBS
INT acVoiceCoderRateMsRtaForwardErrorCorrectionEnable	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.7	INTEGER	read-write	Determines the Microsoft RTA coder forward error correction mode. 0 - Disable. 1 - Enable. Access: Online. AC INI-Param: MSRTAForwardErrorCorrectionEnable
U32 acVoiceCoderRateMsRtaTxBitRate	1.3.6.1.4.1.5003.9.10.4.1.2.1.20.8	Unsigned32	read-write	Determines the Microsoft RTA coder TX bit rate. 0 - Automatic. Any value between 8,800 - 29,000. Access: Online. AC INI-Param: MSRTATxBitRate
acVoiceAGC	1.3.6.1.4.1.5003.9.10.4.1.2.2
INT acVoiceAGCEnable	1.3.6.1.4.1.5003.9.10.4.1.2.2.1	INTEGER	read-write	Activates the AGC (Automatic Gain Control). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEAGC
U32 acVoiceAGCGainSlope	1.3.6.1.4.1.5003.9.10.4.1.2.2.2	Unsigned32	read-write	Determines the AGC (Automatic Gain Control) convergence rate. Range = 0 to 31 (according to acTAGCGainSlope) Default = 3 (= 1 db/sec). Access: Online. AC INI-Param: AGCGAINSLOPE
U32 acVoiceAGCRedirection	1.3.6.1.4.1.5003.9.10.4.1.2.2.3	Unsigned32	read-write	Determines the AGC (Automatic Gain Control) direction. 0 = AGC works on signals from the TDM side 1 = AGC works on signals coming from the Network side. Access: Online. AC INI-Param: AGCREDIRECTION
U32 acVoiceAGCTargetEnergy	1.3.6.1.4.1.5003.9.10.4.1.2.2.4	Unsigned32	read-write	Determines the signal energy value [-dBm] that the AGC (Automatic Gain Control) attempts to attain. Range = 0 to 63. Access: Online. AC INI-Param: AGCTARGETENERGY
U32 acVoiceAGCMinGain	1.3.6.1.4.1.5003.9.10.4.1.2.2.5	Unsigned32	read-write	Defines the minimum gain by the AGC when activated [- db]. Range = 0 to -31. Access: Offline. AC INI-Param: AGCMINGAIN
U32 acVoiceAGCMaxGain	1.3.6.1.4.1.5003.9.10.4.1.2.2.6	Unsigned32	read-write	Defines the maximum gain by the AGC when activated [db]. Range = 0 to 18. Access: Offline. AC INI-Param: AGCMAXGAIN
INT acVoiceAGCDisableFastAdaptation	1.3.6.1.4.1.5003.9.10.4.1.2.2.7	INTEGER	read-write	Disables the AGC Fast Adaptation mode. Enable = 1 Disable = 0. Access: Offline. AC INI-Param: AGCDISABLEFASTADAPTATION
acVoiceEC	1.3.6.1.4.1.5003.9.10.4.1.2.3
INT acVoiceECEnable	1.3.6.1.4.1.5003.9.10.4.1.2.3.1	INTEGER	read-write	Enables or disables the Echo Canceller. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEECHOCANCELLER
INT acVoiceECMaxLength	1.3.6.1.4.1.5003.9.10.4.1.2.3.2	INTEGER	read-write	Defines the maximum board EC (Echo Canceler) length capability. 0 = EC length determined internally to reach maximum channel capacity. 4 = 32 msec 11 = 64 msec 22 = 128 msec TP-1610 only: Using 64 or 128 msec reduces the channel capacity to 200 channels. . Access: Offline. AC INI-Param: MAXECHOCANCELLERLENGTH
INT acVoiceECHybridLoss	1.3.6.1.4.1.5003.9.10.4.1.2.3.3	INTEGER	read-write	Sets the worst case ratio between the signal level transmitted to the hybrid and the echo level returning from hybrid. Set this per worst hybrid in the system in terms of echo return loss. Refer to the enumeration acTECHybridLoss. 0 = 6 dBm 1 = 9 dBm 2 = 0 dBm 3 = 3 dBm. Access: Online. AC INI-Param: ECHYBRIDLOSS
INT acVoiceECToneDetector	1.3.6.1.4.1.5003.9.10.4.1.2.3.4	INTEGER	read-write	Used to configure the Echo Canceler Tone Detector. Detects a 2100 Hz tone at the input signal to the TDM (received signal). Improves Echo Canceler operation accordingly. Detects 2100, 2100 with phase reversals and 2100 with AM. Improves the operation of the Echo Canceler by slowing adaptation when the signal is detected. This data is also used by the fax state machine. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ECEnableToneDetector
INT acVoiceECComfortNoiseGeneration	1.3.6.1.4.1.5003.9.10.4.1.2.3.5	INTEGER	read-write	Use this parameter to enable or enable Echo Canceler Comfort Noise Generation, which generates comfort noise when the Non Linear Processor (NLP) is active. When the NLP ascertains that the signal is echo and not doubletalk and decides to clip, instead of transmitting silence it transmits a synthesized signal similar to the background noise. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ECEnableComfortNoiseGeneration
acVoiceSC	1.3.6.1.4.1.5003.9.10.4.1.2.4
INT acVoiceSCMode	1.3.6.1.4.1.5003.9.10.4.1.2.4.1	INTEGER	read-write	Enables or disables Silence Suppression Mode. 0 = Disable = SILENCE_COMPRESION_DISABLE 1 = Enable = SILENCE_COMPRESION_ENABLE 2 = Enable without adaptation = SILENCE_COMPRESION_ENABLE_NOISE_ADAPTATION_DISABLE. Access: Online. AC INI-Param: ENABLESILENCECOMPRESSION
U32 acVoiceSCVBRCoderDTXMin	1.3.6.1.4.1.5003.9.10.4.1.2.4.2	Unsigned32	read-write	Defines the minimum number of frames gap between two SID frames, when using the EVRC voice activity detector. . Access: Online. AC INI-Param: EVRCDTXMin
U32 acVoiceSCVBRCoderDTXMax	1.3.6.1.4.1.5003.9.10.4.1.2.4.3	Unsigned32	read-write	Defines the maximum number of frames gap between two SID frames, when using the EVRC voice activity detector. Access: Online. AC INI-Param: EVRCDTXMax
U32 acVoiceSCVBRCoderHangover	1.3.6.1.4.1.5003.9.10.4.1.2.4.4	Unsigned32	read-write	For indicating the desired number of silence frames at the beginning of each silence period, when using the VBR CODER silence suppression. . Access: Online. AC INI-Param: VBRCoderHangover
acMediaFaxModemConfig	1.3.6.1.4.1.5003.9.10.4.1.3
acFaxModem	1.3.6.1.4.1.5003.9.10.4.1.3.1
acFMCommon	1.3.6.1.4.1.5003.9.10.4.1.3.1.1
I32 acFMCommonRelayVolume	1.3.6.1.4.1.5003.9.10.4.1.3.1.1.1	Integer32	read-write	Determines the fax gain control. The range -18 to -3 relates to -18.5 dBm to -3.5 dBm in steps of 1 dBm. Access: Online. AC INI-Param: FAXMODEMRELAYVOLUME
INT acFMCommonV34Transport	1.3.6.1.4.1.5003.9.10.4.1.3.1.1.2	INTEGER	read-write	Sets the V.34 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events 4 = AnsMute. Access: Online. AC INI-Param: V34MODEMTRANSPORTTYPE
INT acFMCommonEnableInbandNetworkDetection	1.3.6.1.4.1.5003.9.10.4.1.3.1.1.3	INTEGER	read-write	Enables or disables inband network detection related to fax/modem. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: EnableFaxModemInbandNetworkDetection
acFMBypass	1.3.6.1.4.1.5003.9.10.4.1.3.1.2
INT acFMBypassCoderType	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.1	INTEGER	read-write	Users can use this parameter to set the fax/modem bypass coder (according to acTCoders). 0 = G.711 A-Law 1 = G.711 Mu-Law. Access: Online. AC INI-Param: FAXMODEMBYPASSCODERTYPE
U32 acFMBypassPacketizationPeriod	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.2	Unsigned32	read-write	Defines the number of basic frames to generate one RTP fax/modem bypass packet. Access: Online. AC INI-Param: FAXMODEMBYPASSM
INT acFMBypassBasicPacketInterval	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.3	INTEGER	read-write	Sets the basic Fax / Modem Bypass RTP packet rate. 0 = Default (set internally) (PACKET_INTERVAL_DEFAULT) 1 = 5 msec (PACKET_INTERVAL_5_MSEC) 2 = 10 msec (PACKET_INTERVAL_10_MSEC) 3 = 20 msec (PACKET_INTERVAL_20_MSEC). Access: Online. AC INI-Param: FAXMODEMBYPASSBASICRTPPACKETINTERVAL
U32 acFMBypassDJBufMinDelay	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.4	Unsigned32	read-write	Determines the Jitter Buffer constant delay (in milliseconds) during a Fax & Modem Bypass session. (The minimum Jitter Buffer Size). Range = 0 to 150. Access: Online. AC INI-Param: FAXMODEMBYPASDJBUFMINDELAY
I32 acFMBypassFaxBypassOutputGain	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.5	Integer32	read-write	Defines the fax bypass output gain control. Range: -31 dB to +31 dB in 1 dB steps Default = 0 = No Gain. Access: Online. AC INI-Param: FaxBypassOutputGain
I32 acFMBypassModemBypassOutputGain	1.3.6.1.4.1.5003.9.10.4.1.3.1.2.6	Integer32	read-write	Defines the modem bypass output gain control. Range: -31 dB to +31 dB in 1 dB steps Default = 0 = No Gain. Access: Online. AC INI-Param: ModemBypassOutputGain
acFMNSE	1.3.6.1.4.1.5003.9.10.4.1.3.1.3
U32 acFMNSEPayloadType	1.3.6.1.4.1.5003.9.10.4.1.3.1.3.1	Unsigned32	read-write	Users can use this parameter to modify the NSE packet's payload type. Range = 96 to 127. Access: Online. AC INI-Param: NSEPAYLOADTYPE
INT acFMNSEMode	1.3.6.1.4.1.5003.9.10.4.1.3.1.3.2	INTEGER	read-write	Enables or disables Cisco's NSE fax / modem automatic pass-through mode. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: NSEMODE
acFax	1.3.6.1.4.1.5003.9.10.4.1.3.2
INT acFaxTransportMode	1.3.6.1.4.1.5003.9.10.4.1.3.2.1	INTEGER	read-write	Sets the Fax over IP transport method. 0 = Transparent 1 = Relay 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: FAXTRANSPORTMODE
U32 acFaxBypassPayloadType	1.3.6.1.4.1.5003.9.10.4.1.3.2.2	Unsigned32	read-write	Users can use this parameter to modify the Fax Bypass Mode RTP packet's payload type. In the case of congestion (if the selected payload type is already used for other coders/modes), then a TP_SETUP_PARAMETER_INVALID_ERROR is issued and the payload type is set to the default value (102). It is the user's responsibility to avoid congestion with other payload types. Range = 0 to 127. Access: Online. AC INI-Param: FAXBYPASSPAYLOADTYPE
INT acFaxRelayECMEnable	1.3.6.1.4.1.5003.9.10.4.1.3.2.3	INTEGER	read-write	Enables or disables the using of ECM mode during Fax Relay. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: FAXRELAYECMENABLE
INT acFaxRelayMaxRate	1.3.6.1.4.1.5003.9.10.4.1.3.2.4	INTEGER	read-write	Limits the maximum rate at which fax messages are transmitted. 0 = 2400 bps 1 = 4800 bps 2 = 7200 bps 3 = 9600 bps 4 = 12000 bps 5 = 14400 bps 6 = 16800 bps 7 =19200 bps 8 = 21600 bps 9 = 24000 bps 10 = 26400 bps 11 = 28800 bps 12 = 31200 bps 13 = 33600bps. Access: Online. AC INI-Param: FAXRELAYMAXRATE
U32 acFaxRelayRedundancyDepth	1.3.6.1.4.1.5003.9.10.4.1.3.2.5	Unsigned32	read-write	Determines the depth of redundancy for fax packets. This parameter is applicable only to non-V.21 packets. 0 = No redundancy 1 = 1 packet redundancy 2 = 2 packet redundancy. Access: Online. AC INI-Param: FAXRELAYREDUNDANCYDEPTH
U32 acFaxEnhancedRelayRedundancyDepth	1.3.6.1.4.1.5003.9.10.4.1.3.2.6	Unsigned32	read-write	Determines the number of repetitions to be applied to control packets when using the T.38 standard. 0 = No redundancy 1 = 1 packet redundancy 2 = 2 packet redundancy 3 = 3 packet redundancy 4 = Maximum redundancy. Access: Online. AC INI-Param: FAXRELAYENHANCEDREDUNDANCYDEPTH
INT acFaxCNGDetectorMode	1.3.6.1.4.1.5003.9.10.4.1.3.2.7	INTEGER	read-write	Determines the CNG Detector mode. 0 = Disable 1 = Relay 2 = Event Only. Access: Online. AC INI-Param: CNGDETECTORMODE
INT acFaxV34TransportMethod	1.3.6.1.4.1.5003.9.10.4.1.3.2.8	INTEGER	read-write	Determines the V.34 fax transport method. One of the following values: 0 = Transparent 1 = Relay 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V34FAXTRANSPORTTYPE
INT acFaxT38Version	1.3.6.1.4.1.5003.9.10.4.1.3.2.9	INTEGER	read-write	T38 fax relay version. 0 = T.38 version 0 (from 06/1998) 3 = T.38 version 3 (V.34 over T.38 support) Default = 3. Access: Online. AC INI-Param: T38Version
acModem	1.3.6.1.4.1.5003.9.10.4.1.3.3
INT acModemV22Transport	1.3.6.1.4.1.5003.9.10.4.1.3.3.1	INTEGER	read-write	Sets the V.22 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V22MODEMTRANSPORTTYPE
INT acModemV23Transport	1.3.6.1.4.1.5003.9.10.4.1.3.3.2	INTEGER	read-write	Sets the V.23 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V23MODEMTRANSPORTTYPE
INT acModemV32Transport	1.3.6.1.4.1.5003.9.10.4.1.3.3.3	INTEGER	read-write	Sets the V.32 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events 4 = AnsMute. Access: Online. AC INI-Param: V32MODEMTRANSPORTTYPE
U32 acModemBypassPayloadType	1.3.6.1.4.1.5003.9.10.4.1.3.3.4	Unsigned32	read-write	Users can use this parameter to modify the Modem Bypass Mode RTP packet's payload type. In the case of congestion (if the selected payload type is already used for other coders/modes), then a TP_SETUP_PARAMETER_INVALID_ERROR is issued and the payload type is set to the default value (103). It is the user's responsibility to avoid congestion with other payload types. Range = 0 to 127. Access: Online. AC INI-Param: MODEMBYPASSPAYLOADTYPE
INT acModemBellTransportType	1.3.6.1.4.1.5003.9.10.4.1.3.3.5	INTEGER	read-write	Use this parameter to set the Bell modem transport method. 0 = Transparent 2 = Bypass (enum ByPassEnable) 3 = Transparent with Events (enum EventsOnly). Access: Online. AC INI-Param: BellModemTransportType
INT acModemV21Transport	1.3.6.1.4.1.5003.9.10.4.1.3.3.6	INTEGER	read-write	Sets the V.21 modem transport method (must be set to 0 = Disable). 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V21ModemTransportType
INT acModemEnableV150ModemRelaySupport	1.3.6.1.4.1.5003.9.10.4.1.3.3.7	INTEGER	read-write	Determines whether to enable V.150.1 modem relay support. Range: 0 - Disable 1 - Enable. Access: Offline. AC INI-Param: EnableV150ModemRelaySupport
acV150dot1	1.3.6.1.4.1.5003.9.10.4.1.3.4
U32 acV150dot1AllocationProfile	1.3.6.1.4.1.5003.9.10.4.1.3.4.1	Unsigned32	read-write	Selects the V.150.1 profile, determining how many DSP channels have V.150.1 support. Range = 0 to 3. Access: Offline. AC INI-Param: V1501AllocationProfile
U32 acV150dot1SSEPayloadTypeRx	1.3.6.1.4.1.5003.9.10.4.1.3.4.2	Unsigned32	read-write	SSE payload type RX. Access: Online. AC INI-Param: V1501SSEPayloadTypeRx
U32 acV150dot1SSEPayloadTypeTx	1.3.6.1.4.1.5003.9.10.4.1.3.4.3	Unsigned32	read-write	SSE payload type TX. Access: Online. AC INI-Param: V1501SSEPayloadTypeTx
U32 acV150dot1SSERedundancyDepth	1.3.6.1.4.1.5003.9.10.4.1.3.4.4	Unsigned32	read-write	SSE is a part of V150.1 modem relay protocol and SSE messages are sent over RTP. SSE redundancy refers to the sending of SSE messages several times to increase reliability. This parameter determines the number of times each SSE message is to be resent. Access: Online. AC INI-Param: V1501SSERedundancyDepth
U32 acV150dot1SPRTPayloadTypeRx	1.3.6.1.4.1.5003.9.10.4.1.3.4.5	Unsigned32	read-write	SPRT payload type RX. Access: Online. AC INI-Param: V1501SPRTPayloadTypeRx
U32 acV150dot1SPRTPayloadTypeTx	1.3.6.1.4.1.5003.9.10.4.1.3.4.6	Unsigned32	read-write	SPRT payload type TX. Access: Online. AC INI-Param: V1501SPRTPayloadTypeTx
U32 acV150dot1SPRTTransportChannel0MaxPayloadSize	1.3.6.1.4.1.5003.9.10.4.1.3.4.7	Unsigned32	read-write	SPRT transport channel 0 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel0MaxPayloadSize
U32 acV150dot1SPRTTransportChannel2MaxPayloadSize	1.3.6.1.4.1.5003.9.10.4.1.3.4.8	Unsigned32	read-write	SPRT transport channel 2 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel2MaxPayloadSize
U32 acV150dot1SPRTTransportChannel2MaxWindowSize	1.3.6.1.4.1.5003.9.10.4.1.3.4.9	Unsigned32	read-write	SPRT transport channel 2 max window size. Access: Online. AC INI-Param: V1501SPRTTransportChannel2MaxWindowSize
U32 acV150dot1SPRTTransportChannel3MaxPayloadSize	1.3.6.1.4.1.5003.9.10.4.1.3.4.10	Unsigned32	read-write	SPRT transport channel 3 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel3MaxPayloadSize
acMediaRtpRtcpConfig	1.3.6.1.4.1.5003.9.10.4.1.4
acRtpRtcp	1.3.6.1.4.1.5003.9.10.4.1.4.1
U32 acRtpRtcpBrokenConnectionEventTimeout	1.3.6.1.4.1.5003.9.10.4.1.4.1.1	Unsigned32	read-write	Determines for how long the RTP connection should be broken before the Broken Connection event is issued. In units of 100 msec. . Access: Online. AC INI-Param: BROKENCONNECTIONEVENTTIMEOUT
INT acRtpRtcpBrokenConnectionEventActivationMode	1.3.6.1.4.1.5003.9.10.4.1.4.1.2	INTEGER	read-write	Determines if the broken connection mechanism is activated when the RTP stream is activated or when the first RTP packet is received. 0 = After First incoming packet (default) 1 = Upon channel�s RTP activation. . Access: Online. AC INI-Param: BROKENCONNECTIONEVENTACTIVATIONMODE
INT acRtpRtcpBasicRTPPacketInterval	1.3.6.1.4.1.5003.9.10.4.1.4.1.3	INTEGER	read-write	Selects the RTP packet rate for sample based coders (such as G.711, G.726, G.727). Also applicable for G.729, G.729E & G.728. 0 = Default (set internally) 1 = 5 msec 2 = 10 msec 3 = 20 msec. Access: Online. AC INI-Param: BASICRTPPACKETINTERVAL
INT acRtpRtcpConnectionEstablishNotificationMode	1.3.6.1.4.1.5003.9.10.4.1.4.1.4	INTEGER	read-write	Determines the notification mode for the RTP connection establishment event acEV_CONNECTION_ESTABLISHED. 0 = Notify only after a broken connection event 1 = Also notify when the first RTP packet is received. Access: Online. AC INI-Param: CONNECTIONESTABLISHEMENTNOTIFICATIONMODE
INT acRtpRtcpEnableMediaUDPChecksum	1.3.6.1.4.1.5003.9.10.4.1.4.1.5	INTEGER	read-write	Determines whether to enable the UDP checksum calculation for RTP media TX over IPv4. One of the following possible values: 0 = Disable (No checksum: UDP checksum for IPv4 TX = 0) 1 = Enable (UDP checksum will be in the UDP header upon IPv4 TX) . Access: Offline. AC INI-Param: EnableMediaUDPChecksum
acRtp	1.3.6.1.4.1.5003.9.10.4.1.4.2
U32 acRtpBaseUDPPort	1.3.6.1.4.1.5003.9.10.4.1.4.2.1	Unsigned32	read-write	Defines the lower boundary of UDP ports to be used by the board. The upper boundary is calculated on the basis of BoardBaseUDPPort + 10 * (Number of Channels). This parameter value must be a multiple of 10. . Access: Offline. AC INI-Param: BASEUDPPORT
INT acRtpComfortNoiseEnable	1.3.6.1.4.1.5003.9.10.4.1.4.2.2	INTEGER	read-write	When set to 1 (Enable), SID packets are sent with the RTP SID type (RFC 3389). 0 = Disable 1 = Enable Determines whether Silence Indicator (SID) packets that are sent and received are according to RFC 3389. 0 = Disabled (default). 1 = Enabled. Note: Applicable only to MP-11x and Mediant 1000. . Access: Online. AC INI-Param: ENABLESTANDARDSIDPAYLOADTYPE
INT acRtpEnableRFC2658Interleaving	1.3.6.1.4.1.5003.9.10.4.1.4.2.3	INTEGER	read-write	When enabled, RTP packets include an interleaving byte for VBR coders. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLERFC2658INTERLEAVING
INT acRtpRxTxMode	1.3.6.1.4.1.5003.9.10.4.1.4.2.4	INTEGER	read-write	Selects which RTP directions are enabled. Both Tx and Rx sides can be disabled. 0 = RTPTxRx 1 = RTPTxOnly 2 = RTPRxOnly 3 = RTPUnactive 4 = RTPRxRFC2833Tx. Access: Online. AC INI-Param: RTPDIRECTIONCONTROL
U32 acRtpRFC2833TxPayloadType	1.3.6.1.4.1.5003.9.10.4.1.4.2.5	Unsigned32	read-write	Controls the RFC 2833 Tx Relay RTP Payload type. Range = 96 to 127. Access: Online. AC INI-Param: RFC2833TXPAYLOADTYPE
U32 acRtpRFC2833RxPayloadType	1.3.6.1.4.1.5003.9.10.4.1.4.2.6	Unsigned32	read-write	Controls the RFC 2833 Rx Relay RTP Payload type. Range = 96 to 127. Access: Online. AC INI-Param: RFC2833RXPAYLOADTYPE
U32 acRtpRedundancyPayloadType	1.3.6.1.4.1.5003.9.10.4.1.4.2.7	Unsigned32	read-write	This parameter sets the RFC 2198 (RTP Redundancy) packet's parameter 'RTP Payload Type'. Range: 96 to 127. Access: Online. AC INI-Param: RFC2198PAYLOADTYPE
INT acRtpRedundancyDepth	1.3.6.1.4.1.5003.9.10.4.1.4.2.8	INTEGER	read-write	Redundancy depth of RFC 2198 redundancy packets. 0 = No redundancy 1 = Redundacny depth. Access: Online. AC INI-Param: RTPREDUNDANCYDEPTH
U32 acRtpPacketizationFactor	1.3.6.1.4.1.5003.9.10.4.1.4.2.9	Unsigned32	read-write	Defines the number of DSP payloads for generating one RTP packet. Range = Hardware dependent. Access: Online. AC INI-Param: RTPPACKINGFACTOR
U32 acRtpNoOpPayloadType	1.3.6.1.4.1.5003.9.10.4.1.4.2.10	Unsigned32	read-write	User can modify the Noop packets RTP Payload type by setting this parameter. Range = 96 to 127. Access: Online. AC INI-Param: RTPNOOPPAYLOADTYPE
INT acRtpNoOpEnable	1.3.6.1.4.1.5003.9.10.4.1.4.2.11	INTEGER	read-write	Enables / disable Noop packets sending mode. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: RTPNOOPENABLE
U32 acRtpNoOpInterval	1.3.6.1.4.1.5003.9.10.4.1.4.2.12	Unsigned32	read-write	Used to modify the Noop packets sending interval Parameter value is in milliseconds Default value = 10 sec (10000 msec) Range = 20 to 600000 (20 msec to 10 min - 10 min = 600000). Access: Online. AC INI-Param: RTPNOOPINTERVAL
INT acRtpVBRCoderHeaderFormat	1.3.6.1.4.1.5003.9.10.4.1.4.2.13	INTEGER	read-write	0 - payload only (no header, no toc, no m-factor) 1- support RFC 2658 format, 1 byte for interleaving header (always 0) and toc, no m-factor 2 � payload including toc only, allow m-factor 3- RFC 3358 format . Access: Online. AC INI-Param: VBRCoderHeaderFormat
INT acRtpAMRCoderHeaderFormat	1.3.6.1.4.1.5003.9.10.4.1.4.2.14	INTEGER	read-write	AMR_CODER_HEADER_DEFAULT_FORMAT=0 - old m factor, each frame contains CRM byte and toc RFC_3267_BUNDLING=1 - single CRM byte followed by toc tables RFC_3267_INTERLEAVING=2 - supported as receivers only. Access: Online. AC INI-Param: AMRCODERHEADERFORMAT
INT acRtpAMRFECRedundancyDepth	1.3.6.1.4.1.5003.9.10.4.1.4.2.15	INTEGER	read-write	Sets the AMR / WB-AMR Redundancy depth according to RFC 3267. 0 = No Redundancy 1 = Redundancy depth of a single packet 2 = Redundancy depth of 2 packets 3 = Redundancy depth of 3 packets . Access: Online. AC INI-Param: AMRFECREDUNDANCYDEPTH
U32 acRtpAMRFECNumOfMngtPolicyEntries	1.3.6.1.4.1.5003.9.10.4.1.4.2.16	Unsigned32	read-write	Sets the number of entries to be defined at the AMR management policy table. Each entry defines the policy of a different rate. Access: Online. AC INI-Param: AMRFECNUMBEROFCODECMODES
U32 acRtpAMRFECDelayHysteresis	1.3.6.1.4.1.5003.9.10.4.1.4.2.17	Unsigned32	read-write	Defines the hysteresis of the Delay Threshold for AMR Hand-out events (in msec). Access: Online. AC INI-Param: AMRFECDELAYHYSTERESIS
U32 acRtpAMRFECDelayThreshold	1.3.6.1.4.1.5003.9.10.4.1.4.2.18	Unsigned32	read-write	Defines the one-way delay value (in msec) that may cause the AMR Hand Out report. 0 = 'Hand Out' report is disabled (default). Access: Online. AC INI-Param: AMRFECDELAYTHRESHHOLD
INT acRtpQcelpCoderHeaderFormat	1.3.6.1.4.1.5003.9.10.4.1.4.2.19	INTEGER	read-write	Determines whether to define a separate header format for the QCELP coder (different to the header format of EVRC coder). One of the following values: -1 - QCELP coder uses the same header format as EVRC coder, according to VBRCoderHeaderFormat parameter. 1 to 2 - QCELP coder uses the value defined by this parameter to define its header format. This parameter is relevant only for Control Protocol users. TPNCP and PCI users should always use -1 value. Access: Instant. AC INI-Param: QcelpCoderHeaderFormat
acAMRFECCodecPolicies	1.3.6.1.4.1.5003.9.10.4.1.4.2.21
acAMRFECCodecPoliciesTable	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1		not-accessible
acAMRFECCodecPoliciesEntry	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1		not-accessible
U32 acAMRFECCodecPoliciesIndex	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.1	Unsigned32	not-accessible	AC INI-Param: AMRFECCodecPolicies_Index
ROW acAMRFECCodecPoliciesRowStatus	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.2	RowStatus	read-create	AC INI-Param: N/A
U32 acAMRFECCodecPoliciesRate	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.3	Unsigned32	read-create	AMR Rate x of policy x (values 0-8). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Rate
U32 acAMRFECCodecPoliciesRedundancyLevel	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.4	Unsigned32	read-create	Redundancy Level for policy x. Same values as �RFC 3267 Redundancy� field. Access: Offline. AC INI-Param: AMRFECCodecPolicies_RedundancyLevel
U32 acAMRFECCodecPoliciesThreshold	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.5	Unsigned32	read-create	FLR (Frame Loss Ratio) threshold of policy 1. Values are taken from 3GPP TS 44.318 (0-63). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Threshold
U32 acAMRFECCodecPoliciesHysteresis	1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.6	Unsigned32	read-create	Hysteresis of FLR threshold for policy 1. Values are taken from 3GPP TS 44.318. (0-15). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Hysteresis
acRtcp	1.3.6.1.4.1.5003.9.10.4.1.4.3
U32 acRtcpDisableIntervalRandomization	1.3.6.1.4.1.5003.9.10.4.1.4.3.1	Unsigned32	read-write	Controls whether RTCP report intervals are randomized or whether each report interval accords exactly to the parameter defining RTCP Mean Tx Interval (in milliseconds). 0 = Randomize 1 = Don�t Randomize. Access: Online. AC INI-Param: DISABLERTCPRANDOMIZE
acRtcpXr	1.3.6.1.4.1.5003.9.10.4.1.4.4
I32 acRtcpXrBurstThreshold	1.3.6.1.4.1.5003.9.10.4.1.4.4.1	Integer32	read-write	voice quality monitoring - excessive burst alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONBURSTHR
I32 acRtcpXrDelayThreshold	1.3.6.1.4.1.5003.9.10.4.1.4.4.2	Integer32	read-write	voice quality monitoring - excessive delay alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONDELAYTHR
I32 acRtcpXrEndOofCallRvalDelayThreshold	1.3.6.1.4.1.5003.9.10.4.1.4.4.3	Integer32	read-write	voice quality monitoring - end of call low quality alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONEOCRVALTHR
U32 acRtcpXrGMin	1.3.6.1.4.1.5003.9.10.4.1.4.4.4	Unsigned32	read-write	voice quality monitoring - minimum gap size (number of frames). Access: Online. AC INI-Param: VQMONGMIN
INT acRtcpXrEnable	1.3.6.1.4.1.5003.9.10.4.1.4.4.5	INTEGER	read-write	Enable voice quality monitoring and RTCP xr reports. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: VQMONENABLE
acVideoRtpRtcp	1.3.6.1.4.1.5003.9.10.4.1.4.5
INT acVideoRtpRtcpDisableRtcpIntervalRandomization	1.3.6.1.4.1.5003.9.10.4.1.4.5.1	INTEGER	read-write	Determines whether to enable RTCP Interval Randomization. One of the following values: 0 Enable RTCP Interval Randomization 1 Disable RTCP Interval Randomization . Access: Online. AC INI-Param: VideoDisableRtcpIntervalRandomization
U32 acVideoRtpRtcpMeanTxInterval	1.3.6.1.4.1.5003.9.10.4.1.4.5.2	Unsigned32	read-write	Defines the mean interval between two transmitted RTCP packets (milliseconds). If the interval is set to 0, no RTCP packets are transmitted at all. Access: Online. AC INI-Param: VideoRtcpMeanTxInterval
INT acVideoRtpRtcpBrokenConnectionActivationMode	1.3.6.1.4.1.5003.9.10.4.1.4.5.3	INTEGER	read-write	Broken connection event activation mode. 0 - Activate broken connection after the arrival of the first RTP packet. 1 - Activate broken connection immediately after the Activate RTP command. . Access: Online. AC INI-Param: VideoBrokenConnectionActivationMode
U32 acVideoRtpRtcpBrokenConnectionEventTimeout	1.3.6.1.4.1.5003.9.10.4.1.4.5.4	Unsigned32	read-write	Timeout that defines when broken connection event occurs. Time resolution is 20msec. Access: Online. AC INI-Param: VideoBrokenConnectionEventTimeout
acMediaIBSConfig	1.3.6.1.4.1.5003.9.10.4.1.5
acIBS	1.3.6.1.4.1.5003.9.10.4.1.5.1
INT acIBSAnalogSignalTransportType	1.3.6.1.4.1.5003.9.10.4.1.5.1.1	INTEGER	read-write	Determines the analog signal transport type. 0 = Ignore 1 = Transfer hookflash via RFC 2833. Access: Online. AC INI-Param: ANALOGSIGNALTRANSPORTTYPE
I32 acIBSDTMFVolume	1.3.6.1.4.1.5003.9.10.4.1.5.1.2	Integer32	read-write	Defines and controls the DTMF generation volume [-dBm]. Range = -31 to 0. Access: Online. AC INI-Param: DTMFVOLUME
INT acIBSDTMFTransportType	1.3.6.1.4.1.5003.9.10.4.1.5.1.3	INTEGER	read-write	Defines the type of DTMF transport. 0 = Erase DTMFs from voice transport not relayed to remote 2 = DTMFs not erased are not relayed to remote 3 = DTMFs are muted from the voice stream and relayed according to RFC 2833 7 = DTMFs are sent according to RFC 2833 and muted when received. Access: Online. AC INI-Param: DTMFTRANSPORTTYPE
INT acIBSMFTransportType	1.3.6.1.4.1.5003.9.10.4.1.5.1.4	INTEGER	read-write	Defines the type of MF transport. 0 = Erase MFs from voice transport not relayed to remote 2 = MFs not erased are not relayed to remote 3 = MFs are muted from the voice stream and relayed according to RFC 2833. Access: Online. AC INI-Param: MFTRANSPORTTYPE
INT acIBSTrunkTestingTonesEnable	1.3.6.1.4.1.5003.9.10.4.1.5.1.5	INTEGER	read-write	Enables or disables trunk testing tones. 0 = Disables trunk testing tones 1 = Enables trunk testing tones. Access: Offline. AC INI-Param: ENABLETRUNKTESTINGTONES
INT acIBSCASRelayTransportMode	1.3.6.1.4.1.5003.9.10.4.1.5.1.6	INTEGER	read-write	Controls the ABCD signaling transport type over IP. 0 = No Relay over the network 1 = Enable CAS relay according to RFC 2833. Access: Online. AC INI-Param: CASTRANSPORTTYPE
U32 acIBSRxDtmfHangOverTime	1.3.6.1.4.1.5003.9.10.4.1.5.1.7	Unsigned32	read-write	Used to configure the Voice Silence time (in ms units) after playing DTMF or MF digits to the TDM side that arrived as Relay from the Network side. Range from 0 to 2000, Default 1000. Access: Online. AC INI-Param: RxDtmfHangOverTime
U32 acIBSTxDtmfHangOverTime	1.3.6.1.4.1.5003.9.10.4.1.5.1.8	Unsigned32	read-write	Voice Silence time (in ms units) after detecting the end of DTMF or MF digits at the TDM side when the DTMF Transport Type is either Relay or Mute.This feature allows the user to configure the silence time. . Access: Online. AC INI-Param: TxDtmfHangOverTime
I32 acIBSDTMFTwistControl	1.3.6.1.4.1.5003.9.10.4.1.5.1.9	Integer32	read-write	Defines a delta (in dB) between the high and low frequency component in the DTMF signal. dB Positive values cause the higher frequency component to be stronger than the lower one. Negative values cause the opposite effect. For any parameter value, both components change so that their average is constant. Range = -10 to 10. Access: Offline. AC INI-Param: DTMFGenerationTwist
I32 acIBSNTEMaxDuration	1.3.6.1.4.1.5003.9.10.4.1.5.1.10	Integer32	read-write	Maximal time for sending NTEs (Named Telephony Events) to the network, regardless of the time range when the TDM signal is detected. -1= NTE will stop only upon detection of End event (default). Access: Online. AC INI-Param: NTEMaxDuration
acIBSDetectors	1.3.6.1.4.1.5003.9.10.4.1.5.2
INT acIBSDetectorsMFR1Enable	1.3.6.1.4.1.5003.9.10.4.1.5.2.1	INTEGER	read-write	Enables or disables detection of MFR1 signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFR1DETECTORENABLE
INT acIBSDetectorsMFR2ForwardEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.2	INTEGER	read-write	Enables or disables detection of MFR2 forward signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFR2FORWARDDETECTORENABLE
INT acIBSDetectorsMFR2BackwardEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.3	INTEGER	read-write	Enables or disables detection of MFR2 backward signaling. Access: Online. AC INI-Param: MFR2BACKWARDDETECTORENABLE
INT acIBSDetectorsR1LineEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.4	INTEGER	read-write	Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: R1LINEDETECTORENABLE
INT acIBSDetectorsR2LineEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.5	INTEGER	read-write	Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: R2LINEDETECTORENABLE
INT acIBSDetectorsAC15Enable	1.3.6.1.4.1.5003.9.10.4.1.5.2.6	INTEGER	read-write	Enables or disables detection of Line signaling. Access: Online. AC INI-Param: AC15DETECTORENABLE
INT acIBSDetectorsDTMFEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.7	INTEGER	read-write	Enables or disables detection of DTMF signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: DTMFDETECTORENABLE
INT acIBSDetectorsCallProgressEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.8	INTEGER	read-write	Enables or disables detection of Call Progress Tones. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: CALLPROGRESSDETECTORENABLE
INT acIBSDetectorsUserDefinedToneEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.9	INTEGER	read-write	Enables or disables detection of User Defined Tones signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: USERDEFINEDTONEDETECTORENABLE
INT acIBSDetectorsDetectionRedirection	1.3.6.1.4.1.5003.9.10.4.1.5.2.10	INTEGER	read-write	Determines the IBS (In-Band Signaling) Detection Direction. 0 = PCM 1 = Network. Access: Online. AC INI-Param: IBSDETECTIONREDIRECTION
INT acIBSDetectorsSS4Enable	1.3.6.1.4.1.5003.9.10.4.1.5.2.11	INTEGER	read-write	Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: SS4DETECTORENABLE
INT acIBSDetectorsMFSS5Enable	1.3.6.1.4.1.5003.9.10.4.1.5.2.12	INTEGER	read-write	Enables or disables detection of MF SS5 line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFSS5DETECTORENABLE
INT acIBSDetectorsSS5Enable	1.3.6.1.4.1.5003.9.10.4.1.5.2.13	INTEGER	read-write	Detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: SS5DETECTORENABLE
INT acIBSDetectorsSITEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.14	INTEGER	read-write	Enables or disables SIT (Special Information Tone) detection according to the ITU-T recommendation E.180/Q.35. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: SITDETECTORENABLE
INT acIBSDetectorsCOTEnable	1.3.6.1.4.1.5003.9.10.4.1.5.2.15	INTEGER	read-write	Enables or disables Continuity Test tone detection and generation according to the ITU-T Q.724 recommendation. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLECONTINUITYTONES
INT acIBSDetectorsR1DetectionStandard	1.3.6.1.4.1.5003.9.10.4.1.5.2.16	INTEGER	read-write	This parameter determines which one of the R1 MF protocol flavors will be used for detection. 0 = ITU 1 = R1.5. Access: Offline. AC INI-Param: R1DetectionStandard
U32 acIBSDetectorsUDTDetectorFrequencyDeviation	1.3.6.1.4.1.5003.9.10.4.1.5.2.17	Unsigned32	read-write	Defines the deviation allowed for the detection of each signal frequency. Units are in Hertz. Valid values range 1-50. Default value 50 Hz. . Access: Offline. AC INI-Param: UDTDETECTORFREQUENCYDEVIATION
U32 acIBSDetectorsCPTDetectorFrequencyDeviation	1.3.6.1.4.1.5003.9.10.4.1.5.2.18	Unsigned32	read-write	Defines the deviation allowed for the detection of each CPT signal frequency. Units are in Hertz. Valid values range 1-30. Default value 10 Hz. . Access: Offline. AC INI-Param: CPTDETECTORFREQUENCYDEVIATION
acIPMediaConfig	1.3.6.1.4.1.5003.9.10.4.1.6
acIPMedia	1.3.6.1.4.1.5003.9.10.4.1.6.1
INT acIPMediaDSPDetectorsEnable	1.3.6.1.4.1.5003.9.10.4.1.6.1.1	INTEGER	read-write	Enables or disables DSP IP Media Detectors. Enabling this parameter might reduce the board channel capacity. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLEDSPIPMDETECTORS
acIPMAnswerDetector	1.3.6.1.4.1.5003.9.10.4.1.6.2
INT acIPMAnswerDetectorEnable	1.3.6.1.4.1.5003.9.10.4.1.6.2.1	INTEGER	read-write	Enables or disables activation of the AD (Answer Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEANSWERDETECTOR
U32 acIPMAnswerDetectorActivityDelay	1.3.6.1.4.1.5003.9.10.4.1.6.2.2	Unsigned32	read-write	Controls (in 100 msec resolution) the time between sending Activation command (AnswerDetector = 1) and the time that the detector actually starts to work. Range = 0 to 0x3FF. Access: Online. AC INI-Param: ANSWERDETECTORACTIVITYDELAY
U32 acIPMAnswerDetectorSilenceTime	1.3.6.1.4.1.5003.9.10.4.1.6.2.3	Unsigned32	read-write	This parameter controls the silence time period (in 100 msec resolution) from no speech input until the END_OF_SPEECH event is sent. 10 = 1 second Range = 0 to 0x3FF. Access: Online. AC INI-Param: ANSWERDETECTORSILENCETIME
INT acIPMAnswerDetectorRedirection	1.3.6.1.4.1.5003.9.10.4.1.6.2.4	INTEGER	read-write	Determines the AD (Answer Detector) Redirection. 0 (PCM) = Speech from the PCM side is detected 1 (Network) = Speech from the IP side is detected. Access: Online. AC INI-Param: ANSWERDETECTORREDIRECTION
U32 acIPMAnswerDetectorSensitivity	1.3.6.1.4.1.5003.9.10.4.1.6.2.5	Unsigned32	read-write	Controls the AD (Answer Detector) sensitivity. The allowed values are different for different boards: DSP Gen2-based products: range 0 - 2, default 0. DSP Gen2-based products: range 0 - 7, default 3. Lowest value matches highest sensitivity and vice versa. Access: Online. AC INI-Param: ANSWERDETECTORSENSITIVITY
acIPMEnergyDetector	1.3.6.1.4.1.5003.9.10.4.1.6.3
INT acIPMEnergyDetectorEnable	1.3.6.1.4.1.5003.9.10.4.1.6.3.1	INTEGER	read-write	Activates the ED (Energy Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEENERGYDETECTOR
U32 acIPMEnergyDetectorQualityFactor	1.3.6.1.4.1.5003.9.10.4.1.6.3.2	Unsigned32	read-write	Determines the ED's (Energy Detector's) sensitivity (0 -10). 0 = Insensitive 10 = Most Sensitive Range = 0 to 10. Access: Online. AC INI-Param: ENERGYDETECTORQUALITYFACTOR
U32 acIPMEnergyDetectorThreshold	1.3.6.1.4.1.5003.9.10.4.1.6.3.3	Unsigned32	read-write	Defines the ED's (Energy Detector's) threshold. A signal exceeding the threshold invokes an 'Above' or 'Below' event. ActualThreshold = -44 dBm + (EDThreshold * 6) Default = 3 = -26 dBm Range: 0 to 7. Access: Online. AC INI-Param: ENERGYDETECTORTHRESHOLD
INT acIPMEnergyDetectorEnergyRedirection	1.3.6.1.4.1.5003.9.10.4.1.6.3.4	INTEGER	read-write	Selects the direction of the energy detection. 0 = Detect from the TDM side 1 = Detect from the network side. Access: Online. AC INI-Param: ENERGYDETECTORREDIRECTION
acIPMediaPatternDetector	1.3.6.1.4.1.5003.9.10.4.1.6.4
INT acIPMediaPatternDetectorEnable	1.3.6.1.4.1.5003.9.10.4.1.6.4.1	INTEGER	read-write	Enables or disables activation of the PD (Pattern Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEPATTERNDETECTOR
U32 acIPMediaPatternDetectorDetectionThreshold	1.3.6.1.4.1.5003.9.10.4.1.6.4.2	Unsigned32	read-write	Defines the number of consecutive patterns to trigger the pattern detection event. Range = 0 to 31. Access: Offline. AC INI-Param: PDTHRESHOLD
acIPMediaAMD	1.3.6.1.4.1.5003.9.10.4.1.6.5
INT acIPMediaAMDDetectionDirection	1.3.6.1.4.1.5003.9.10.4.1.6.5.1	INTEGER	read-write	Determines the AMD (Answer Machine Detector) detection direction. One of the following values: 0 = Detection from the TDM side 1 = Detection from the Network side. Access: Online. AC INI-Param: AMDDETECTIONDIRECTION
U32 acIPMediaAMDSensitivity	1.3.6.1.4.1.5003.9.10.4.1.6.5.2	Unsigned32	read-write	Determines the AMD (Answer Machine Detector) detection sensitivity: 0 = Best detection of an answering machine 7 = Best detection of a live call. Access: Online. AC INI-Param: AMDDetectionSensitivity
U32 acIPMediaAMDDetectionSensitivityHighResolution	1.3.6.1.4.1.5003.9.10.4.1.6.5.3	Unsigned32	read-write	Determines the AMD (Answer Machine Detector) high resolution detection sensitivity. The high resolution has 16 levels of sensitivity while the normal resolution (Answer Machine Detector Sensitivity) has 8 levels. 0 = Best detection of an answering machine 15 = Best detection of a live call. Access: Online. AC INI-Param: AMDDetectionSensitivityHighResolution
INT acIPMediaAMDSensitivityResolution	1.3.6.1.4.1.5003.9.10.4.1.6.5.4	INTEGER	read-write	Determines the AMD (Answer Machine Detector) detection sensitivity resolution: 0 = Normal detection sensitivity resolution (8 sensitivity levels) 1 = High detection sensitivity resolution (16 sensitivity levels). Access: Online. AC INI-Param: AMDSensitivityResolution
U32 acIPMediaAMDBeepDetectionTimeout	1.3.6.1.4.1.5003.9.10.4.1.6.5.5	Unsigned32	read-write	Determines the AMD (Answer Machine Detector) Beep detection timeout. Units of 100 milliseconds, values from 0 to 1638 (163.8 seconds). Access: Online. AC INI-Param: AMDBeepDetectionTimeout
U32 acIPMediaAMDBeepDetectionSensitivity	1.3.6.1.4.1.5003.9.10.4.1.6.5.6	Unsigned32	read-write	Determines the AMD (Answer Machine Detector) Beep detection sensitivity. 0 - Least sensitive. 3 - Most sensitive. Access: Online. AC INI-Param: AMDBeepDetectionSensitivity
acIPMConference	1.3.6.1.4.1.5003.9.10.4.1.6.6
U32 acIPMConferenceGASNMinInterval	1.3.6.1.4.1.5003.9.10.4.1.6.6.1	Unsigned32	read-write	Minimum interval between Active Speaker Notification (ASN) events. An ASN event reports on the active speakers in a conference. The event is issued whenever the active speakers change. units = 100 ms Minimum configurable interval between events is 500 ms (5 units). Access: Instant. AC INI-Param: ACTIVESPEAKERSNOTIFICATIONMININTERVAL
U32 acIPMConferenceEnergythreshold	1.3.6.1.4.1.5003.9.10.4.1.6.6.2	Unsigned32	read-write	Conference - Minimum energy level for a user to be included in Active Speaker Notification (ASN) events (units: -dBm). Valid range 0 to (-39) dbm. Access: Instant. AC INI-Param: ActiveSpeakerEnergyThreshold
INT acIPMConferenceEnableHDConference	1.3.6.1.4.1.5003.9.10.4.1.6.6.3	INTEGER	read-write	Enable\Disable HD Conference. Access: Offline. AC INI-Param: EnableHDConference
acIPMVideoConference	1.3.6.1.4.1.5003.9.10.4.1.6.7
U32 acIPMVideoConferenceSwitchingInterval	1.3.6.1.4.1.5003.9.10.4.1.6.7.1	Unsigned32	read-write	Determines the video view rotation interval in seconds. Applicable when using timer trigger switching mode. Access: Online. AC INI-Param: VideoConferenceSwitchingInterval
INT acIPMVideoConferenceEnableActiveSpeakerHighlight	1.3.6.1.4.1.5003.9.10.4.1.6.7.2	INTEGER	read-write	Highlights the speaker for participants viewing a symmetric layout (2x2 or 3x3) . 0 - Don't highlight active speaker. 1 - Highlight active speaker. Access: Online. AC INI-Param: VideoEnableActiveSpeakerHighlight
INT acIPMVideoConferenceParticipantType	1.3.6.1.4.1.5003.9.10.4.1.6.7.3	INTEGER	read-write	Indicates a participant's capabilities in the conference. Regular (2) � Regular participant who is able to both send and receive video. . Access: Online. AC INI-Param: VideoConferenceParticipantType
INT acIPMVideoConferenceParticipantTriggerMode	1.3.6.1.4.1.5003.9.10.4.1.6.7.4	INTEGER	read-write	Participant trigger mode defines the trigger for modifying the participant's view. Voice Activated Video Switch (0) � A participant�s view will be changed according to the active speakers� detection. Timer (1) � A participant�s view is rotated every configured time among the different video participants in the conference. Fixed (3) � A participant�s view is fixed. . Access: Online. AC INI-Param: VideoConferenceParticipantTriggerMode
INT acIPMVideoConferenceParticipantLayout	1.3.6.1.4.1.5003.9.10.4.1.6.7.5	INTEGER	read-write	Indicates the participant's view layout. 1 user (0). 22 users (1). All same size. 33 users (2). All same size. . Access: Online. AC INI-Param: VideoConferenceParticipantLayout
INT acIPMVideoConferenceEnableConferenceParticipantSelfView	1.3.6.1.4.1.5003.9.10.4.1.6.7.6	INTEGER	read-write	Self view indication. 0 - The participant cannot view himself 1 - The participant can view himself. Access: Online. AC INI-Param: VideoEnableConferenceParticipantSelfView
acMediaCallerIDConfig	1.3.6.1.4.1.5003.9.10.4.1.7
acCallerID	1.3.6.1.4.1.5003.9.10.4.1.7.1
INT acCallerIDTypes	1.3.6.1.4.1.5003.9.10.4.1.7.1.1	INTEGER	read-write	Defines the supported Caller ID standard. 0 = Bellcore 1 = ETSI 2 = NTT 4 = British 16 = ETSI_ETS 17 = Denmark 18 = Indian 19 = Brazilian. Access: Online. AC INI-Param: CALLERIDTYPE
INT acCallerIDTransportType	1.3.6.1.4.1.5003.9.10.4.1.7.1.2	INTEGER	read-write	Defines the CallerID Transport type. 0 = Disable 1 = Relay 3 = Mute. Access: Online. AC INI-Param: CallerIDTransportType
U32 acCallerIDDTMFBasedMaxDigits	1.3.6.1.4.1.5003.9.10.4.1.7.1.3	Unsigned32	read-write	Determines the maximum number of DTMF digits in a DTMF-based Caller ID string. Range = 0 to 26. Access: Online. AC INI-Param: MAXDTMFDIGITSINCIDSTRING
U32 acCallerIDDTMFBasedMinDigits	1.3.6.1.4.1.5003.9.10.4.1.7.1.4	Unsigned32	read-write	Determines the mimumum number of DTMF digits in a DTMF-based Caller ID string. Range = 0 to 26. Access: Online. AC INI-Param: MINDTMFDIGITSINCIDSTRING
INT acCallerIDNTTDIDSignallingForm	1.3.6.1.4.1.5003.9.10.4.1.7.1.5	INTEGER	read-write	Configures the signalling format used when generating an NTT DID. 0 = FSK Siganl 1 = DTMF Based Signal. Access: Online. AC INI-Param: NTTDIDSignallingForm
acMediaNetworkConfig	1.3.6.1.4.1.5003.9.10.4.1.8
acMediaNetwork	1.3.6.1.4.1.5003.9.10.4.1.8.1
INT acMediaNetworkDisableNAT	1.3.6.1.4.1.5003.9.10.4.1.8.1.1	INTEGER	read-write	Enables or disables the NAT feature. 0 = Do not disable NAT 1 = Disable NAT. Access: Online. AC INI-Param: DISABLENAT
U32 acMediaNetworkRtpIpTos	1.3.6.1.4.1.5003.9.10.4.1.8.1.2	Unsigned32	read-write	Sets value of IP Type Of Service field in IP header for all packets generated from this channel. Follow the acTIPTOS enumeration. Access: Instant. AC INI-Param: IPTOS
U32 acMediaNetworkRtpIpPrecedence	1.3.6.1.4.1.5003.9.10.4.1.8.1.3	Unsigned32	read-write	Sets value of the IP precedence field in the IP header for all packets generated from this channel. Follow the acTIPPrecedence enumeration. Access: Instant. AC INI-Param: IPPRECEDENCE
U32 acMediaNetworkIPDiffServ	1.3.6.1.4.1.5003.9.10.4.1.8.1.4	Unsigned32	read-write	Defines the value of the 'DiffServ' field in the IP header for media (RTP) traffic. Range: 0 to 63. Access: Instant. AC INI-Param: IPDIFFSERV
INT acMediaNetworkInboundLatchMode	1.3.6.1.4.1.5003.9.10.4.1.8.1.5	INTEGER	read-write	Determines the way of handling incoming media packets from non-expected address/port. Access: Online. AC INI-Param: InboundMediaLatchMode
acMediaJBConfig	1.3.6.1.4.1.5003.9.10.4.1.9
acJitterBuffer	1.3.6.1.4.1.5003.9.10.4.1.9.1
U32 acJitterBufferMinDelay	1.3.6.1.4.1.5003.9.10.4.1.9.1.1	Unsigned32	read-write	Defines the Dynamic Jitter Buffer Minimum Delay (in msec). Recommended value for a regular voice call is 10. Access: Online. AC INI-Param: DJBUFMINDELAY
U32 acJitterBufferOptFactor	1.3.6.1.4.1.5003.9.10.4.1.9.1.2	Unsigned32	read-write	Defines the Dynamic Jitter Buffer frame error/delay optimization. Recommended value for a regular voice call is 10. Access: Online. AC INI-Param: DJBUFOPTFACTOR
acVideoJitterBuffer	1.3.6.1.4.1.5003.9.10.4.1.9.2
U32 acVideoJitterBufferMinDelay	1.3.6.1.4.1.5003.9.10.4.1.9.2.1	Unsigned32	read-write	Jitter buffer minimum delay in milliseconds. Must be less than JitterBufferMaxDelay. Access: Online. AC INI-Param: VideoJitterBufferMinDelay
U32 acVideoJitterBufferMaxDelay	1.3.6.1.4.1.5003.9.10.4.1.9.2.2	Unsigned32	read-write	Jitter buffer maximum delay in milliseconds. Access: Online. AC INI-Param: VideoJitterBufferMaxDelay
U32 acVideoJitterBufferDJBOptimizationFactor	1.3.6.1.4.1.5003.9.10.4.1.9.2.3	Unsigned32	read-write	JB Optimization Factor controls the jitter buffer's adaptation rates A High factor means fast adaptation when jitter increases, and a slow adaptation when jitter decrease. Small factor means slow adaptation when jitter increases, and a fast adaptation when jitter decreases. . Access: Online. AC INI-Param: VideoDJBOptimizationFactor
acMediaAggregation	1.3.6.1.4.1.5003.9.10.4.1.10
U32 acMediaAggregationRemoteBaseUDPPort	1.3.6.1.4.1.5003.9.10.4.1.10.1	Unsigned32	read-write	Remote Base UDP Port For Aggrigation. Access: Offline. AC INI-Param: REMOTEBASEUDPPORT
U32 acMediaAggregationL1L1ComplexRxUDPPort	1.3.6.1.4.1.5003.9.10.4.1.10.2	Unsigned32	read-write	The UDP port for the incoming (from the remote side) and the outgoing (destination UDP) packets, for Complex Multiplexed RTP mode. Access: Offline. AC INI-Param: L1L1ComplexRxUDPPort
U32 acMediaAggregationL1L1ComplexTxUDPPort	1.3.6.1.4.1.5003.9.10.4.1.10.3	Unsigned32	read-write	The Source UDP port for the outgoing UDP Multiplexed RTP packets, for Complex-Multiplex RTP mode. Access: Offline. AC INI-Param: L1L1ComplexTxUDPPort
acStreamingCache	1.3.6.1.4.1.5003.9.10.4.1.11
U32 acStreamingCacheSize	1.3.6.1.4.1.5003.9.10.4.1.11.1	Unsigned32	read-write	Sets the streaming cache size in MBs. The remaining size (out of 32MBs) is used as VoicePrompt storage. Access: Offline. AC INI-Param: gStreamingCacheSize
I32 acStreamingCacheRefreshTime	1.3.6.1.4.1.5003.9.10.4.1.11.2	Integer32	read-write	Defines the streaming cache data refresh time in minutes. If -1 is set, refresh is off. Access: Offline. AC INI-Param: gStreamingCacheRefreshTime
U32 acStreamingCacheClearService	1.3.6.1.4.1.5003.9.10.4.1.11.3	Unsigned32	read-write	reset the streaming cache. Access: Instant. AC INI-Param: N/A
acMediaVideoConfig	1.3.6.1.4.1.5003.9.10.4.1.12
U32 acMediaVideoConfigEncoderIntraInterval	1.3.6.1.4.1.5003.9.10.4.1.12.1	Unsigned32	read-write	Sets the frequency for the number of frames at which the encoder outputs an Intra frame. Access: Online. AC INI-Param: VideoEncoderIntraInterval
U32 acMediaVideoConfigMaxPacketSize	1.3.6.1.4.1.5003.9.10.4.1.12.2	Unsigned32	read-write	Sets the maximum packet size in bytes. Access: Online. AC INI-Param: VideoMaxPacketSize
U32 acMediaVideoConfigTargetBitrate	1.3.6.1.4.1.5003.9.10.4.1.12.3	Unsigned32	read-write	Sets the target output bit rate. Access: Online. AC INI-Param: VideoTargetBitrate
U32 acMediaVideoConfigQualityParameterForRateControl	1.3.6.1.4.1.5003.9.10.4.1.12.4	Unsigned32	read-write	This value determines the trade off between video quality and frame rate. A low value indicates a higher quality with a lower frame rate and vice versa. Access: Online. AC INI-Param: VideoQualityParameterForRateControl
INT acMediaVideoConfigRateControlType	1.3.6.1.4.1.5003.9.10.4.1.12.5	INTEGER	read-write	Sets bitrate output to either a constant or a variable bit rate. CBR (0) � Constant Bit Rate. VBR (1) � Variable Bit Rate. Target Bitrate indicates the target average output bit rate. . Access: Online. AC INI-Param: VideoRateControlType
INT acMediaVideoConfigEnableReSyncHeader	1.3.6.1.4.1.5003.9.10.4.1.12.6	INTEGER	read-write	Indicates whether to add a video packet header to every packet in order to increase error resilience. 0 - Disable 1 - Enable. Access: Online. AC INI-Param: VideoEnableReSyncHeader
INT acMediaVideoConfigEnableAudioVideoSynchronization	1.3.6.1.4.1.5003.9.10.4.1.12.7	INTEGER	read-write	Determines whether to enable audio and video synchronization. 0 - No synchronization between audio and video streams 1 - Synchronization between audio and video streams . Access: Online. AC INI-Param: EnableAudioVideoSynchronization
acIPMediaChannels	1.3.6.1.4.1.5003.9.10.4.1.13
INT acIPMediaChannelsEnable	1.3.6.1.4.1.5003.9.10.4.1.13.1	INTEGER	read-write	Whether to enable DSP channels reservation for IPmedia support. Relevant for Mediant 1000 board only. One of the following possible 0 = Disable 1 - Enable. Access: Offline. AC INI-Param: EnableIPMediaChannels
acIPMediaChannelsResourcesTable	1.3.6.1.4.1.5003.9.10.4.1.13.21		not-accessible	IPMedia channels info
acIPMediaChannelsResourcesEntry	1.3.6.1.4.1.5003.9.10.4.1.13.21.1		not-accessible
U32 acIPMediaChannelsResourcesIndex	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.1	Unsigned32	not-accessible	Index Field for line. Internal parameter. AC INI-Param: IPMediaChannels_Index
ROW acIPMediaChannelsResourcesRowStatus	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.2	RowStatus	read-create	ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
INT acIPMediaChannelsResourcesAction	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.3	INTEGER	read-create	Mangement Field for ACTIONS. Internal parameter. AC INI-Param: N/A
INT acIPMediaChannelsResourcesActionRes	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.4	INTEGER	read-only	Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: N/A
U32 acIPMediaChannelsResourcesModuleID	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.5	Unsigned32	read-create	Refers to M1K board only, module at which slot. Access: Offline. AC INI-Param: IPMediaChannels_ModuleID
U32 acIPMediaChannelsResourcesDSPChannelsReserved	1.3.6.1.4.1.5003.9.10.4.1.13.21.1.6	Unsigned32	read-create	How many DSP channels reserve for IPMedia channels. Access: Offline. AC INI-Param: IPMediaChannels_DSPChannelsReserved
acMediaStatus	1.3.6.1.4.1.5003.9.10.4.2
acIPLegs	1.3.6.1.4.1.5003.9.10.4.2.1
acIPLegsTable	1.3.6.1.4.1.5003.9.10.4.2.1.1		not-accessible
acIPLegsEntry	1.3.6.1.4.1.5003.9.10.4.2.1.1.1		not-accessible
U32 acIPLegsLegIndex	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.1	Unsigned32	not-accessible	Describes Rtp Endpoint In A Specific Call. AC INI-Param: N/A
U32 acIPLegsCallIndex	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.2	Unsigned32	read-only	Decribes The Call which The Rtp EndPoint Participant In It. AC INI-Param: N/A
INT acIPLegsRTPActive	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.3	INTEGER	read-only	Decribes whether the RTP is active or not. AC INI-Param: N/A
INT acIPLegsCoderType	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.4	INTEGER	read-only	describes the coder Type. AC INI-Param: N/A
INT acIPLegsSilenceCompression	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.5	INTEGER	read-only	Enables or Disables the Silence Compression. AC INI-Param: N/A
INT acIPLegsDTMFDetection	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.6	INTEGER	read-only	Enables or Disables the DTMF Detection. AC INI-Param: N/A
U32 acIPLegsLocalRTPPort	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.7	Unsigned32	read-only	Describes the RTP port of the Leg. AC INI-Param: N/A
IP acIPLegsRemoteRTPAddress	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.8	IpAddress	read-only	Describes the RTP address. AC INI-Param: N/A
INT acIPLegsFaxTransportType	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.9	INTEGER	read-only	Describes the Fax transfor Type currently working. AC INI-Param: N/A
U32 acIPLegsRxPackets	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.10	Unsigned32	read-only	Describes the received packets on the Leg. AC INI-Param: N/A
U32 acIPLegsTxPackets	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.11	Unsigned32	read-only	Describes the Transmitted packets on the Leg. AC INI-Param: N/A
U32 acIPLegsRxBytes	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.12	Unsigned32	read-only	Describes the received Bytes on the Leg. AC INI-Param: N/A
U32 acIPLegsTxBytes	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.13	Unsigned32	read-only	Describes the Transmitted packets on the Leg. AC INI-Param: N/A
U32 acIPLegsJitter	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.14	Unsigned32	read-only	Describes the Jitter on the Leg. AC INI-Param: N/A
U32 acIPLegsPacketLoss	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.15	Unsigned32	read-only	Describes the Lost packets on the Leg. AC INI-Param: N/A
U32 acIPLegsSSRCOfSender	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.16	Unsigned32	read-only	Describes the SSRC Of the Sender. AC INI-Param: N/A
U32 acIPLegsDSPDevice	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.17	Unsigned32	read-only	Describes the DSP Device Of the Leg. AC INI-Param: N/A
STR acIPLegsLegName	1.3.6.1.4.1.5003.9.10.4.2.1.1.1.18	SnmpAdminString	read-only	Describes the Leg Name as in the Control Protocol. AC INI-Param: N/A

RFC description

Manages AudioCodes media processing including DSP configuration, codec selection, and channel capacity.

Start monitoring AudioCodes Mediant-series gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AC-MEDIA-MIB

What Is AC-MEDIA-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description