All MIBs › ZTE-AN-CFM2-MIB
Organization: ZTE Corporation
Last Updated: 2017-11-14
Category: ZTE Access Node (ZTE-AN) Management
Description: Manages ZTE access node Connectivity Fault Management (CFM) including MEPs, MAs, and continuity checks.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ZTE-AN-CFM2-MIB?
This is ZTE's private MIB implementing Connectivity Fault Management (CFM) per IEEE 802.1ag and ITU-T Y.1731 for its access node product line, used to detect Ethernet-layer connectivity faults across a carrier network. It exposes configuration for Maintenance Endpoints (MEPs) and Maintenance Associations (MAs) along with the continuity-check and fault-detection results between them. Its monitoring emphasis is squarely on fault detection: loss-of-continuity and remote-defect conditions between MEPs surface network-path faults, essentially functioning as a software-level early-warning system for connectivity problems rather than reporting on hardware sensors like temperature or power. It implements the IEEE 802.1ag/ITU-T Y.1731 CFM standards and typically coexists with an access node's underlying bridge/VLAN MIBs. It is deployed on ZTE access and aggregation nodes in carrier Ethernet networks where operators need proactive end-to-end fault detection across the metro/access segment. Engineers can download the ZTE-AN-CFM2-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-CFM2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ZTE access node
- carrier Ethernet aggregation switch
Monitoring Examples
No sample object names were provided for this MIB, so specific identifiers can't be cited here. Conceptually, an operator would poll per-MEP/MA continuity-check status to detect a loss-of-continuity or remote-defect condition between two Ethernet maintenance endpoints, revealing a fault in the access/aggregation path before it is reported as a customer-facing service outage.
What Can Be Monitored
- MEP/MA continuity check status
- connectivity fault/defect state
- remote MEP reachability
This MIB depends on
Related MIBs
Imported Objects
From IEEE8021-CFM-MIB
| Dot1afCfmIndexIntegerNextFree | |
| Dot1agCfmCcmInterval | |
| Dot1agCfmEgressActionFieldValue | |
| Dot1agCfmFngState | |
| Dot1agCfmHighestDefectPri | |
| Dot1agCfmIdPermission | |
| Dot1agCfmIngressActionFieldValue | |
| Dot1agCfmLowestAlarmPri | |
| Dot1agCfmMDLevel | |
| Dot1agCfmMaintAssocName | |
| Dot1agCfmMaintAssocNameType | |
| Dot1agCfmMaintDomainName | |
| Dot1agCfmMaintDomainNameType | |
| Dot1agCfmMepDefects | |
| Dot1agCfmMepId | |
| Dot1agCfmMepIdOrZero | |
| Dot1agCfmMhfCreation | |
| Dot1agCfmMpDirection | |
| Dot1agCfmRelayActionFieldValue |
From IF-MIB
| InterfaceIndex |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| MacAddress | |
| RowStatus |
From ZTE-AN-SMI
| zxAnOam | OBJECT-IDENTITY |
From ZTE-AN-TC-MIB
| VlanId | |
| ZxAnSubIfIndex |
How to Use in IPNetwork Monitor
Example using zxAnCfm2LMepCciSentCcms OID:
Select a ZTE access node, carrier Ethernet aggregation switch (802.1ag/Y.1731 MEP continuity-check/fault status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxAnCfm2LMepCciSentCcms into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of CCM packets transmitted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| zxAnCfm2Mib | 1.3.6.1.4.1.3902.1082.80.45 | This MIB defines managed objects of the Connectivity Fault Management module for managing Y.1731. | ||
| zxAnCfm2GlobalObjects | 1.3.6.1.4.1.3902.1082.80.45.1 | |||
| BIT zxAnCfm2Capabilities | 1.3.6.1.4.1.3902.1082.80.45.1.1 | Bits | read-only | The management capabilities of CFM. The bit value 1 means the function represented by this bit is supported by this equipment. bit 0: value 1 means supporting zxAnCfm2LMepDmTwoWayFdMsrR1Max, zxAnCfm2LMepDmTwoWayFdMsrR2Max, zxAnCfm2LMepDmTwoWayFdMsrR3Max, zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max and zxAnCfm2LMepDmOneWayIfdvMsrR3Max in zxAnCfm2LocalMepTable. |
| INT zxAnCfm2Enable | 1.3.6.1.4.1.3902.1082.80.45.1.2 | INTEGER | read-write | Enable/disable the CFM functions. |
| INT zxAnCfm2TlvIgnoreEnable | 1.3.6.1.4.1.3902.1082.80.45.1.3 | INTEGER | read-write | Enable/disable TLV ignoring. enabled(1): The TLV of the packet is ignored from the peer side. disabled(2): The TLV of the packet is not ignored from the peer side. |
| zxAnCfm2Objects | 1.3.6.1.4.1.3902.1082.80.45.2 | |||
| zxAnCfm2MdObjects | 1.3.6.1.4.1.3902.1082.80.45.2.1 | |||
| zxAnCfm2MdGlobalObjects | 1.3.6.1.4.1.3902.1082.80.45.2.1.1 | |||
| NUM zxAnCfm2MdTableNextIndex | 1.3.6.1.4.1.3902.1082.80.45.2.1.1.1 | Dot1afCfmIndexIntegerNextFree | read-only | An unused value for zxAnCfm2MdIndex in the zxAnCfm2MdTable, or a zero to indicate that none exist. |
| zxAnCfm2MdTable | 1.3.6.1.4.1.3902.1082.80.45.2.1.2 | not-accessible | The Maintenance Domain table. Each row in the table represents a different Maintenance Domain. A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance. | |
| zxAnCfm2MdEntry | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1 | not-accessible | The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage. | |
| U32 zxAnCfm2MdIndex | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.1 | Unsigned32 | not-accessible | The index to the Maintenance Domain table. zxAnCfm2MdTableNextIndex needs to be inspected to find an available index for row-creation. Referential integrity is required, i.e., the index needs to be persistent upon a reboot or restart of a device. The index can never be reused for other Maintenance Domain. The index value SHOULD keep increasing up to the time that they wrap around. This is to facilitate access control based on OID. |
| NUM zxAnCfm2MdFormat | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.2 | Dot1agCfmMaintDomainNameType | read-create | The type (and thereby format) of the Maintenance Domain Name. |
| NUM zxAnCfm2MdName | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.3 | Dot1agCfmMaintDomainName | read-create | The Maintenance Domain name. The type/format of this object is determined by the value of the zxAnCfm2MdFormat object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain. |
| DOT zxAnCfm2MdMdLevel | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.4 | Dot1agCfmMDLevel | read-create | The Maintenance Domain Level. |
| DOT zxAnCfm2MdMhfCreation | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.5 | Dot1agCfmMhfCreation | read-create | Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is not allowed. |
| DOT zxAnCfm2MdMhfIdPermission | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.6 | Dot1agCfmIdPermission | read-create | Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value sendIdDefer is not allowed. |
| NUM zxAnCfm2MdMaNextIndex | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.7 | Dot1afCfmIndexIntegerNextFree | read-only | Value to be used as the index of the MA table entries, to the zxAnCfm2MaTable for this Maintenance Domain when the management entity wants to create a new row in those tables. |
| ROW zxAnCfm2MdRowStatus | 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MdEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnCfm2MaObjects | 1.3.6.1.4.1.3902.1082.80.45.2.2 | |||
| zxAnCfm2MaTable | 1.3.6.1.4.1.3902.1082.80.45.2.2.2 | not-accessible | The Maintenance Association table. Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance. Creation of a Service Instance establishes a connectionless association among the selected DSAPs. Configuring a Maintenance association End Point (MEP) at each of the DSAPs creates a Maintenance Association (MA) to monitor that connectionless connectivity. The MA is identified by a Short MA Name that is unique within the Maintenance Domain and chosen to facilitate easy identification of the Service Instance. Together, the Maintenance Domain Name and the Short MA Name form the Maintenance Association Identifier (MAID) that is carried in CFM Messages to identify incorrect connectivity among Service Instances. A small integer, the Maintenance association End Point Identifier (MEPID), identifies each MEP among those configured on a single MA (802.1ag clauses 3.19 and 18.2). This table uses two indices, first index is the index of the Maintenance Domain table. The second index is the same as the index of the dot1agCfmMaCompEntry for the same MA. The writable objects in this table need to be persistent upon reboot or restart of a device. | |
| zxAnCfm2MaEntry | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1 | not-accessible | The MA table entry. | |
| I32 zxAnCfm2MaIndex | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.1 | Integer32 | not-accessible | Index of the MA table zxAnCfm2MdMaNextIndex needs to be inspected to find an available index for row-creation. |
| NUM zxAnCfm2MaFormat | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.2 | Dot1agCfmMaintAssocNameType | read-create | The type (and thereby format) of the Maintenance Association Name. |
| NUM zxAnCfm2MaName | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.3 | Dot1agCfmMaintAssocName | read-create | The Short Maintenance Association name. The type/format of this object is determined by the value of the zxAnCfm2MaFormat object. This name MUST be unique within a maintenance domain. |
| NUM zxAnCfm2MaCcmInterval | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.4 | Dot1agCfmCcmInterval | read-create | Interval between CCM (Continuity Check Messages) transmissions to be used by all MEPs in the MA. When set this variable, value 0 is not supported. |
| VLA zxAnCfm2MaPrimarySVid | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.5 | VlanId | read-create | Primary SVLAN ID of the MEP. |
| I32 zxAnCfm2MaPrimaryCVid | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.6 | Integer32 | read-create | Primary CVLAN ID of the MEP. Value 0 means the primary CVLAN is not configured. |
| I32 zxAnCfm2MaCcmTimeoutCoefficient | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.7 | Integer32 | read-create | CCM check timeout coefficient. The CCM check timeout is the result of zxAnCfm2MaCcmTimeoutCoefficient multiplied by zxAnCfm2MaCcmInterval, and then divided by 10. |
| ROW zxAnCfm2MaRowStatus | 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MaEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnCfm2MpObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3 | |||
| zxAnCfm2LocalMepObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.2 | |||
| zxAnCfm2LocalMepTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2 | not-accessible | The Maintenance Association End Point (MEP) table. Each row in the table represents a different MEP. An MEP is an actively managed CFM entity, associated with a specific DSAP of a Service Instance, which can generate and receive CFM PDUs and track any responses. It is an end point of a single Maintenance Association, and is an endpoint of a separate Maintenance Entity for each of the other MEPs in the same Maintenance Association (802.1ag clause 3.19). This table uses three indices. The first two indices are the indices of the Maintenance Domain and MA tables, the reason being that an MEP is always related to an MA and Maintenance Domain. | |
| zxAnCfm2LocalMepEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1 | not-accessible | The local MEP table entry. | |
| DOT zxAnCfm2MpIdentifier | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.1 | Dot1agCfmMepId | not-accessible | Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID. |
| NUM zxAnCfm2LMepIfIndex | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.2 | InterfaceIndex | read-create | The index of the NNI/UNI ports on the device. |
| ZXA zxAnCfm2LMepSubIfIndex | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.3 | ZxAnSubIfIndex | read-create | The sub-interface of the NNI/UNI ports on the device. |
| DOT zxAnCfm2LMepDirection | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.4 | Dot1agCfmMpDirection | read-create | The direction in which the MEP faces on the Bridge port. |
| INT zxAnCfm2LMepAdminStatus | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.5 | INTEGER | read-create | The administrative status of the MEP. |
| DOT zxAnCfm2LMepLowestPriDefect | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.6 | Dot1agCfmLowestAlarmPri | read-create | An integer value specifying the lowest priority defect that is allowed to generate fault alarm. |
| INT zxAnCfm2LMepCcmSendEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.7 | INTEGER | read-create | Enable/disable sending CCM messages. |
| I32 zxAnCfm2LMepCcmLtmPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.8 | Integer32 | read-create | The priority value for CCMs and LTMs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for this variable from the priority regeneration table by extracting the highest priority value in this table on this MEPs bridge port. (1 is lowest, then 2, then 0, then 3-7). |
| INT zxAnCfm2LMepCcmDestMacType | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.9 | INTEGER | read-create | The destination MAC address type of CCM packet. |
| INT zxAnCfm2LMepCcmRdiSendEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.10 | INTEGER | read-create | Enable/disable RDI sending in CCM packet. |
| INT zxAnCfm2LMepCcmRdiTrustEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.11 | INTEGER | read-create | Enable/disable trusting the CCM packet from remote MEP with RDI. |
| C32 zxAnCfm2LMepCciSentCcmsEx | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.12 | Counter32 | read-only | The total number of CCM packets transmitted. |
| DOT zxAnCfm2LMepFngState | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.13 | Dot1agCfmFngState | read-only | Current state of the MEP Fault Notification Generator State Machine. |
| INT zxAnCfm2LMepHighestPriDefect | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.14 | INTEGER | read-only | The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state. |
| DOT zxAnCfm2LMepDefects | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.15 | Dot1agCfmMepDefects | read-only | A vector of Boolean error conditions from Table 20-1, any of which may be true: DefRDICCM(0) DefMACstatus(1) DefRemoteCCM(2) DefErrorCCM(3) DefXconCCM(4) |
| INT zxAnCfm2LMepAisEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.16 | INTEGER | read-create | Enable/disable the ETH-AIS function. |
| INT zxAnCfm2LMepAisLckInterval | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.17 | INTEGER | read-create | The interval for AISMs and LCKMs transmitted by the MEP. |
| I32 zxAnCfm2LMepAisPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.18 | Integer32 | read-create | Priority. 3 bit value to be used in the VLAN tag, if present in the AIS frame. |
| INT zxAnCfm2LMepAisCondition | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.19 | INTEGER | read-only | Whether the MEP is in AIS condition or not. |
| OCT zxAnCfm2LMepClientMegLevel | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.20 | OCTET STRING | read-create | MEG level at which the most immediate client layer MIPs and MEPs exist, zxAnCfm2LMepClientMegLevel, must be higher than the MD level. For example, configure client level list values '01 03 05 FF FF FF FF' to an MEP. It means that in the client level list only level 1, level 3 and level 5 take effect. Please notice: the range of this object is 0~7. Each client level in the list must be larger than the MD level of the MEP. '0xff' means client level not configured. The number of these client level is fixed with 7. |
| MAC zxAnCfm2LMepMacAddress | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.21 | MacAddress | read-only | The MAC address of the MEP. |
| I32 zxAnCfm2LMepDmTwoWayFdMsrR1Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.22 | Integer32 | read-create | The maximum value of the first two-way frame delay measurements range. The minimum value is 0. |
| I32 zxAnCfm2LMepDmTwoWayFdMsrR2Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.23 | Integer32 | read-create | The maximum value of the second two-way frame delay measurements range. The minimum value is zxAnCfm2LMepDmTwoWayFdMsrR1Max. |
| I32 zxAnCfm2LMepDmTwoWayFdMsrR3Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.24 | Integer32 | read-create | The maximum value of the third two-way frame delay measurements range. The minimum value is zxAnCfm2LMepDmTwoWayFdMsrR2Max. This value is also the minimum value of the fourth two-way frame delay measurements range. The maximum value of the fourth range is plus infinity. |
| I32 zxAnCfm2LMepDmOneWayIfdvMsrR1Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.25 | Integer32 | read-create | The maximum value of the first one-way inter-frame delay variation measurements range. The minimum value is 0. |
| I32 zxAnCfm2LMepDmOneWayIfdvMsrR2Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.26 | Integer32 | read-create | The maximum value of the second one-way inter-frame delay variation measurements range. The minimum value is zxAnCfm2LMepDmOneWayIfdvMsrR1Max. |
| I32 zxAnCfm2LMepDmOneWayIfdvMsrR3Max | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.27 | Integer32 | read-create | The maximum value of the third one-way inter-frame delay variation measurements range. The minimum value is zxAnCfm2LMepDmOneWayIfdvMsrR2Max. This value is also the minimum value of the fourth one-way inter-frame delay variation measurements range. The maximum value of the fourth range is plus infinity. |
| ROW zxAnCfm2LMepRowStatus | 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2LocalMepEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnCfm2RemoteMepObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.3 | |||
| zxAnCfm2RemoteMepTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2 | not-accessible | This table includes remote MEP configuration. A remote MEP is an MEP, it can use in all the CFM tests. It represents the destination of the test when the test uses MEPID as its destination. | |
| zxAnCfm2RemoteMepEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1 | not-accessible | The remote MEP table entry. | |
| MAC zxAnCfm2RMepMacAddress | 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.1 | MacAddress | read-create | The MAC address of the remote MEP. |
| INT zxAnCfm2RMepAdminStatus | 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.2 | INTEGER | read-create | The administrative status of the remote MEP. |
| ROW zxAnCfm2RMepRowStatus | 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2RemoteMepEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnCfm2MipObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.4 | |||
| zxAnCfm2MipTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2 | not-accessible | This table includes MIP configuration. An MIP can be used in all the CFM tests. MIP is a CFM entry, associated with a single Maintenance Domain, and thus with single MD level, it can generate CFM PDUs, but only in response to received CFM PDUs. | |
| zxAnCfm2MipEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1 | not-accessible | The MIP table entry. When a manager wants to create a remote MEP, it must comply with the multi-variables usage rule that all the mib variables related to same fuction must be in one snmp set operation, the variables have two type: mandatory and optional. Mandatory variables must be in the one snmp set operation. Optional variables may be in the one snmp set operation with the mandatory variables, but must not be used alone. To create an MIP, there are two cases base on the MIP is assigned to a physical port or a logical port, and the mandatory and optional variables for each case are different. To create an MIP assign to physical port: - mandatoty: zxAnCfm2MipRowStatus zxAnCfm2MipIfIndex - optional : zxAnCfm2MipSubIfIndex zxAnCfm2MipIfIndex, zxAnCfm2MipSubIfIndex can not be modified. | |
| NUM zxAnCfm2MipIfIndex | 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.1 | InterfaceIndex | read-create | The index of the NNI/UNI ports on the device. |
| ZXA zxAnCfm2MipSubIfIndex | 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.2 | ZxAnSubIfIndex | read-create | The sub-interface of the NNI/UNI ports on the device. |
| ROW zxAnCfm2MipRowStatus | 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MipEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnCfm2ConnectMeasureObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.21 | |||
| zxAnCfm2MepLoopBackOperTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2 | not-accessible | The Maintenance Association End Point (MEP) connectivity operation table stores all the managed objects for sending LBM. LBM Managed objects in the MEP table enables the management entity to initiate transmission of Loopback messages. It will signal the MEP that it SHOULD transmit some number of Loopback messages and detect the detection (or lack thereof) of the corresponding Loopback messages. Steps to use entries in this table: 1) Wait for zxAnCfm2MepTransLbmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepTransLbmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepTransLbmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepTransLbmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepTransLbmEnable objects (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1)a.. This ensures that two cooperating NMSes will not step on each others toes. Setting this MIB object does not set the corresponding LBIactive state machine variable. 3) Setup the different data to be sent (number of messages, optional TLVs,...). 4) Record the current values of zxAnCfm2MepLbrInInOrder, zxAnCfm2MepLbrInOutOfOrder, and zxAnCfm2MepLbrBadMsdu. 5) Check the value of zxAnCfm2MepTransLbmResultOk to find out if the operation was successfully initiated or not. 6) Monitor the value of zxAnCfm2MepTransLbmEnable. When it is reset to false, the last LBM has been transmitted. Wait an additional 5 seconds to ensure that all LBRs have been returned. 7) Compare zxAnCfm2MepLbrInInOrder, zxAnCfm2MepLbrInOutOfOrder, and zxAnCfm2MepLbrBadMsdu to their old values from step 4, above, to get the results of the test. | |
| zxAnCfm2MepLoopBackOperEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1 | not-accessible | The Loopback table entry. | |
| INT zxAnCfm2MepTransLbmEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.1 | INTEGER | read-write | Enable/disable the LBM function. |
| I32 zxAnCfm2MepTransLbmMessages | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.2 | Integer32 | read-write | The total number of Loopback messages to be transmitted. |
| INT zxAnCfm2MepLbmDestMacType | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.3 | INTEGER | read-write | The destination MAC address type of LBM packet. |
| INT zxAnCfm2MepLbAppType | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.4 | INTEGER | read-write | The application type of LBM. It means to verify bidirectional connectivity of an MEP with an MIP or a peer MEP. |
| MAC zxAnCfm2MepTransLbmDestMacAddr | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.5 | MacAddress | read-write | The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column zxAnCfm2MepTransLbmDestMepType is 'macAddr'. |
| DOT zxAnCfm2MepTransLbmDestMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.6 | Dot1agCfmMepIdOrZero | read-write | The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the column zxAnCfm2MepTransLbmDestMepType is 'mepId'. |
| INT zxAnCfm2MepTransLbmDestMepType | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.7 | INTEGER | read-write | The MEP type. macAddr(1): The unicast destination MAC address of the target MEP is used for Loopback transmission. mepId(2): The MEP ID of the target MEP is used for Loopback transmission. |
| I32 zxAnCfm2MepTransLbmDataTlvLength | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.8 | Integer32 | read-write | An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent. The value 0 means not configured and no data tlv is included in the frame. |
| I32 zxAnCfm2MepTransLbmVlanPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.9 | Integer32 | read-write | The priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority. |
| I32 zxAnCfm2MepTransLbmTimeout | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.10 | Integer32 | read-write | LMB timeout. If the MEP does not receive LBR in time, the LBR packets may be discarded. |
| INT zxAnCfm2MepTransLbmResultOk | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.30 | INTEGER | read-only | The result of the operation: yes(1): The Loopback Message(s) will be (or has been) sent. no(2): The Loopback Message(s) will not be sent. |
| U32 zxAnCfm2MepTransLbmSeqNumber | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.31 | Unsigned32 | read-only | The Loopback Transaction Identifier (zxAnCfm2MepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if zxAnCfm2MepTransLbmResultOk is false. |
| U32 zxAnCfm2MepNextLbmTransId | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.32 | Unsigned32 | read-only | Next sequence number/transaction identifier to be sent in a Loopback message. This sequence number can be zero because it wraps around. |
| C32 zxAnCfm2MepLbrInInOrder | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.33 | Counter32 | read-only | The total number of valid, in-order Loopback Replies received. |
| C32 zxAnCfm2MepLbrInOutOfOrder | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.34 | Counter32 | read-only | The total number of valid, out-of-order Loopback Replies received. |
| C32 zxAnCfm2MepLbrBadMsdu | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.35 | Counter32 | read-only | The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3). |
| C32 zxAnCfm2MepLbrOut | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.36 | Counter32 | read-only | The total number of Loopback Replies transmitted. |
| I32 zxAnCfm2MepLbMaxLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.37 | Integer32 | read-only | The maximum latency. |
| I32 zxAnCfm2MepLbMinLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.38 | Integer32 | read-only | The minimum latency. |
| I32 zxAnCfm2MepLbAvgLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.39 | Integer32 | read-only | The average latency. |
| zxAnCfm2MepMultiLbrTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3 | not-accessible | This table includes multicast Loopback result. Before start a mulitcast LBM user must first get all the entry of this table, and after the LBM is over, user must get all the entry of this table again, and compare all the entry to get the result of multicast LBM. | |
| zxAnCfm2MepMultiLbrEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1 | not-accessible | The multicast Lookback Reply table entry. All the varibles in this entry is read only. | |
| MAC zxAnCfm2MepMultiLbrDestMepMac | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.1 | MacAddress | not-accessible | The mac address of the destination MEP. |
| C32 zxAnCfm2MepMultiLbrMepLbrIn | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.2 | Counter32 | read-only | The total LBR packets received by the MEP from the same remote MEP that responsed the LBR PDUs when received LBM from the local MEP. |
| I32 zxAnCfm2MepMultiLbMaxLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.3 | Integer32 | read-only | The maximum latency. |
| I32 zxAnCfm2MepMultiLbMinLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.4 | Integer32 | read-only | The minimum latency. |
| I32 zxAnCfm2MepMultiLbAvgLatency | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.5 | Integer32 | read-only | The average latency. |
| zxAnCfm2MepLinkTraceOperTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4 | not-accessible | The Maintenance Association End Point (MEP) LinkTrace operation table stores all the managed objects for sending LTM. LTM Managed objects in the MEP table enables the management entity to initiate transmission of LinkTrace messages. It will signal the MEP that it SHOULD transmit some number of LinkTrace messages and detect the detection (or lack thereof) of the corresponding LinkTrace messages. Steps to use entries in this table: 1) Wait for zxAnCfm2MepTransLtmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepTransLtmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepTransLtmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepTransLtmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepTransLtmEnable objects (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1)a.. This ensures that two cooperating NMSes will not step on each others toes. Setting this MIB object does not set the corresponding LBIactive state machine variable. 3) Setup the different data to be sent (number of messages, ,...). 4) Check the value of zxAnCfm2MepTransLtmResultOk to find out if the operation was successfully initiated or not. 5) Monitor the value of zxAnCfm2MepTransLtmEnable. When it is reset to false, the last LTM has been transmitted. Wait an additional 5 seconds to ensure that all LTRs have been returned. 6) Read the zxAnCfm2MepLinkTraceReplyTable to get the results of the test. | |
| zxAnCfm2MepLinkTraceOperEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1 | not-accessible | The LinkTrace table entry. All the varibles writable in the entry can be modified after the MEP entry created, and the variables are reset when the entry is destroyed. | |
| INT zxAnCfm2MepTransLtmEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.1 | INTEGER | read-create | Enable/disable the LTM function. |
| BIT zxAnCfm2MepTransLtmFlags | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.2 | Bits | read-create | The flags field for LTMs transmitted by the MEP. |
| MAC zxAnCfm2MepTransLtmDestMacAddr | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.3 | MacAddress | read-create | The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column zxAnCfm2MepTransLtmTargetMepType is 'macAddr'. |
| DOT zxAnCfm2MepTransLtmTargetMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.4 | Dot1agCfmMepIdOrZero | read-create | An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address will be used if the value of the column zxAnCfm2MepTransLtmTargetMepType is 'mepId'. |
| INT zxAnCfm2MepTransLtmTargetMepType | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.5 | INTEGER | read-create | The MEP type. macAddr(1): The unicast destination MAC address of the target MEP is used for LinkTrace transmission. mepId(2): The MEPID of the target MEP is used for LinkTrace transmission. |
| I32 zxAnCfm2MepTransLtmTtl | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.6 | Integer32 | read-create | The LTM TTL field. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each LTR (Link Trace Responder) that handles the LTM. The value returned in the LTR is one less than that received in the LTM. If the LTM TTL is 0 or 1, the LTM is not forwarded to the next hop, and if 0, no LTR is generated. |
| I32 zxAnCfm2MepTransLtmTimeout | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.7 | Integer32 | read-create | The LTM timeout. If the MEP does not receive LTR in time, the LTR packets may be discarded. |
| INT zxAnCfm2MepTransLtmResultOk | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.30 | INTEGER | read-only | The result of the operation: yes(1): The LinkTrace Message(s) will be (or has been) sent. no(2): The LinkTrace Message(s) will not be sent. |
| U32 zxAnCfm2MepTransLtmSeqNumber | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.31 | Unsigned32 | read-only | The LTM Transaction Identifier (zxAnCfm2MepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if zxAnCfm2MepTransLtmResultOk is false. |
| U32 zxAnCfm2MepLtmNextSeqNumber | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.32 | Unsigned32 | read-only | Next transaction identifier/sequence number to be sent in a LinkTrace message. This sequence number can be zero because it wraps around. |
| C32 zxAnCfm2MepUnexpLtrIn | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.33 | Counter32 | read-only | The total number of unexpected LTRs received (20.39.1). |
| zxAnCfm2MepLinkTraceReplyTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5 | not-accessible | This table extends the MEP table and contains a list of LinkTrace replies received by a specific MEP in response to a LinkTrace message. SNMP SMI does not allow to state in a MIB that an object in a table is an array. The solution is to take the index (or indices) of the first table and add one or more indices. | |
| zxAnCfm2MepLinkTraceReplyEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1 | not-accessible | The LinkTrace Reply table entry. | |
| U32 zxAnCfm2MepLtrSeqNumber | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.1 | Unsigned32 | not-accessible | Transaction identifier/Sequence number returned by a previous transmit LinkTrace message command, indicating which LTM's response is going to be returned. |
| U32 zxAnCfm2MepLtrReceiveOrder | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.2 | Unsigned32 | not-accessible | An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. zxAnCfm2MepLtrReceiveOrder are assigned sequentially from 1, in the order that the LinkTrace Initiator received the LTRs. |
| I32 zxAnCfm2MepLtrTtl | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.3 | Integer32 | read-only | TTL field value for a returned LTR. |
| INT zxAnCfm2MepLtrForwarded | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.4 | INTEGER | read-only | Whether a LTM was forwarded by the responding MP. |
| INT zxAnCfm2MepLtrTerminalMep | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.5 | INTEGER | read-only | Whether the forwarded LTM reached a MEP enclosing its MA. |
| OCT zxAnCfm2MepLtrLastEgressId | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.6 | OCTET STRING | read-only | An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP LinkTrace Initiator that originated, or the LinkTrace Responder that forwarded, the LTM to which this LTR is the response. This is the same value as the Egress Identifier TLV of that LTM. |
| OCT zxAnCfm2MepLtrNextEgressId | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.7 | OCTET STRING | read-only | An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the LinkTrace Responder that transmitted this LTR, and can forward the LTM to the next hop. This is the same value as the Egress Identifier TLV of the forwarded LTM, if any. If the FwdYes bit of the Flags field is false, the contents of this field are undefined, i.e. any value can be transmitted, and the field is ignored by the receiver. |
| DOT zxAnCfm2MepLtrRelay | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.8 | Dot1agCfmRelayActionFieldValue | read-only | Value returned in the Relay Action field. |
| DOT zxAnCfm2MepLtrIngress | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.9 | Dot1agCfmIngressActionFieldValue | read-only | The value returned in the Ingress Action Field of the LTM. |
| MAC zxAnCfm2MepLtrIngressMac | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.10 | MacAddress | read-only | MAC address returned in the ingress MAC address field. |
| DOT zxAnCfm2MepLtrEgress | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.11 | Dot1agCfmEgressActionFieldValue | read-only | The value returned in the Egress Action Field of the LTM. |
| MAC zxAnCfm2MepLtrEgressMac | 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.12 | MacAddress | read-only | MAC address returned in the egress MAC address field. |
| zxAnCfm2PerfMeasureObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.22 | |||
| zxAnCfm2MepDmOperTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2 | not-accessible | The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending DMM. Steps to use entries in this table: 1) Wait for zxAnCfm2MepDmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepDmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepDmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepDmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepDmEnable and other delay measurement objects (such as zxAnCfm2MepDmPriority,...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varbind). For the snmpSetSerialNo varbind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepDmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepDmEnable. When it is reset to false, the last DMM has been transmitted. 5) Get the results of the test from zxAnCfm2MepDmRltTable. | |
| zxAnCfm2MepDmOperEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1 | not-accessible | The Delay Measurement table entry. | |
| I32 zxAnCfmMepDmTestId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.1 | Integer32 | not-accessible | The frame delay measurement identifier of the specified MEP. 8 measurements can be simultaneously activated on the MEP. |
| INT zxAnCfm2MepDmEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.2 | INTEGER | read-create | Enable/disable the DM function. If the value is disable, the DM test can not be started. |
| DOT zxAnCfm2MepDmTargetMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.3 | Dot1agCfmMepIdOrZero | read-create | The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the DM is to be sent. It will be used if DMM destination MAC address type is unicast. |
| INT zxAnCfm2MepDmFrameSize | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.4 | INTEGER | read-create | The DM frame size. |
| INT zxAnCfm2MepDmAppType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.5 | INTEGER | read-create | The application type of the DM. |
| INT zxAnCfm2MepDmInterval | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.6 | INTEGER | read-create | The interval at which DMMs are sent by an MEP. |
| I32 zxAnCfm2MepDmDuration | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.7 | Integer32 | read-create | The duration of DM test. It can be configured when zxAnCfm2MepDmOperType is onDemand. |
| I32 zxAnCfm2MepDmPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.8 | Integer32 | read-create | The priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. |
| INT zxAnCfm2MepDmOperType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.9 | INTEGER | read-create | The operation type of the DM. |
| INT zxAnCfm2MepDmResultOk | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.30 | INTEGER | read-only | The result of the operation: yes(1): The Delay Measurement Message(s) will be (or has been) sent. no(2): The Delay Measurement Message(s) will not be sent. |
| zxAnCfm2MepDmRltTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3 | not-accessible | This table includes multicast or unicast frame delay measurement result. | |
| zxAnCfm2MepDmRltEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1 | not-accessible | The delay measurement result table entry. | |
| DOT zxAnCfm2DmRemoteMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.1 | Dot1agCfmMepId | not-accessible | Remote MEP identifier, which receives frame delay measurement packets and responses delay measurement reply packets. |
| DAT zxAnCfm2MepDmStartTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.2 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval. |
| DAT zxAnCfm2MepDmEndTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.3 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval. |
| I32 zxAnCfm2MepDmElapsedTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.4 | Integer32 | read-only | The elapsed time of the delay measurement interval. |
| C32 zxAnCfm2MepDmSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.5 | Counter32 | read-only | The packets of delay measurement sent. |
| C32 zxAnCfm2MepDmReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.6 | Counter32 | read-only | The packets of delay measurement received. |
| C32 zxAnCfm2MepDmTwoWayFdMsr | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.7 | Counter32 | read-only | The count of two-way frame delay measurements. |
| I32 zxAnCfm2MepDmTwoWayFdMsrAvg | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.8 | Integer32 | read-only | The average two-way frame delay measurements. |
| I32 zxAnCfm2MepDmTwoWayFdMsrMin | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.9 | Integer32 | read-only | The minimum two-way frame delay measurements. |
| I32 zxAnCfm2MepDmTwoWayFdMsrMax | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.10 | Integer32 | read-only | The maximum two-way frame delay measurements. |
| C32 zxAnCfm2MepDmOneWayFwdIfdvMsr | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.11 | Counter32 | read-only | The count of inter-frame delay variation measurements in the forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrAvg | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.12 | Integer32 | read-only | The average one-way inter-frame delay variation measurements in forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrMax | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.13 | Integer32 | read-only | The maximum one-way inter-frame delay variation measurements in forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrMin | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.14 | Integer32 | read-only | The minimum one-way inter-frame delay variation measurements in forward direction. |
| C32 zxAnCfm2MepDmOneWayBwdIfdvMsr | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.15 | Counter32 | read-only | The count of inter-frame delay variation measurements in the backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrAvg | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.16 | Integer32 | read-only | The average one-way inter-frame delay variation measurements in backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrMax | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.17 | Integer32 | read-only | The maximum one-way inter-frame delay variation measurements in backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrMin | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.18 | Integer32 | read-only | The minimum one-way inter-frame delay variation measurements in backward direction. |
| I32 zxAnCfm2MepDmTwoWayFdMsrR1C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.19 | Integer32 | read-only | The count in the first two-way frame delay measurements range which is [0, zxAnCfm2LMepDmTwoWayFdMsrR1Max). |
| I32 zxAnCfm2MepDmTwoWayFdMsrR2C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.20 | Integer32 | read-only | The count in the second two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR1Max, zxAnCfm2LMepDmTwoWayFdMsrR2Max). |
| I32 zxAnCfm2MepDmTwoWayFdMsrR3C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.21 | Integer32 | read-only | The count in the third two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR2Max, zxAnCfm2LMepDmTwoWayFdMsrR3Max). |
| I32 zxAnCfm2MepDmTwoWayFdMsrR4C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.22 | Integer32 | read-only | The count in the fourth two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR3Max, plus infinity). |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrR1C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.23 | Integer32 | read-only | The count in the first one-way inter-frame delay variation measurements range which is [0, zxAnCfm2LMepDmOneWayIfdvMsrR1Max) in the forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrR2C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.24 | Integer32 | read-only | The count in the second one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max) in the forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrR3C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.25 | Integer32 | read-only | The count in the third one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR2Max, zxAnCfm2LMepDmOneWayIfdvMsrR3Max) in the forward direction. |
| I32 zxAnCfm2MepDmOneWayFwdIfdvMsrR4C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.26 | Integer32 | read-only | The count in the fourth one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR3Max, plus infinity) in the forward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrR1C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.27 | Integer32 | read-only | The count in the first one-way inter-frame delay variation measurements range which is [0, zxAnCfm2LMepDmOneWayIfdvMsrR1Max) in the backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrR2C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.28 | Integer32 | read-only | The count in the second one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max) in the backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrR3C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.29 | Integer32 | read-only | The count in the third one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR2Max, zxAnCfm2LMepDmOneWayIfdvMsrR3Max) in the backward direction. |
| I32 zxAnCfm2MepDmOneWayBwdIfdvMsrR4C | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.30 | Integer32 | read-only | The count in the fourth one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR3Max, plus infinity) in the backward direction. |
| zxAnCfm2MepLmOperTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4 | not-accessible | The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending LMM. Steps to use entries in this table: 1) Wait for zxAnCfm2MepLmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepLmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepLmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepLmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepLmEnable and other frame loss measurement objects (such as zxAnCfm2MepLmPriority,...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varbind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepLmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepLmEnable. When it is reset to false, the last LMM has been transmitted. 5) Get the results of the test from zxAnCfm2MepLmRltTable. | |
| zxAnCfm2MepLmOperEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1 | not-accessible | The Loss Measurement table entry. | |
| I32 zxAnCfm2MepLmTestId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.1 | Integer32 | not-accessible | The packet loss measurement identifier of the specified MEP, only one on-demand or one proactive LM can be activated simultaneously on the specified MEP. |
| INT zxAnCfm2MepLmEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.2 | INTEGER | read-create | Enable/disable the LM function. If the value is disable the LM test can not be started. |
| DOT zxAnCfm2MepLmTargetMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.3 | Dot1agCfmMepIdOrZero | read-create | The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LM is to be sent. This variable will be used if the LMM destination MAC address type is unicast, if not configured the multicast LM will be sent. |
| INT zxAnCfm2MepLmAppType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.4 | INTEGER | read-create | The application type of the LM. |
| INT zxAnCfm2MepLmInterval | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.5 | INTEGER | read-create | The interval at which LMMs are sent by an MEP. |
| I32 zxAnCfm2MepLmDuration | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.6 | Integer32 | read-create | The duration of LM. It can be configured when zxAnCfm2MepLmOperType is onDemand. |
| I32 zxAnCfm2MepLmPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.7 | Integer32 | read-create | The priority. 3 bit value to be used in the VLAN tag, if present in the LM frame. |
| INT zxAnCfm2MepLmOperType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.8 | INTEGER | read-create | The operation type of the LM. |
| INT zxAnCfm2MepLmResultOk | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.30 | INTEGER | read-only | The result of the operation: yes(1): The Loss Measurement Message(s) will be (or has been) sent. no(2): The Loss Measurement Message(s) will not be sent. |
| zxAnCfm2MepLmRltTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5 | not-accessible | This table includes multicast or unicast frame loss measurement result. | |
| zxAnCfm2MepLmRltEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1 | not-accessible | The loss measurement result table entry. | |
| DOT zxAnCfm2LmRemoteMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.1 | Dot1agCfmMepId | not-accessible | Remote MEP identifier, which receives frame loss measurement packets and responses loss measurement reply packets. |
| DAT zxAnCfm2MepLmStartTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.2 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval. |
| DAT zxAnCfm2MepLmEndTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.3 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval. |
| I32 zxAnCfm2MepLmElapsedTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.4 | Integer32 | read-only | The elapsed time of the measurement interval. |
| C32 zxAnCfm2MepLmSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.5 | Counter32 | read-only | The number of frame loss measurement packets sent. |
| C32 zxAnCfm2MepLmReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.6 | Counter32 | read-only | The number of frame loss measurement packets received. |
| C64 zxAnCfm2MepLmFwdSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.7 | Counter64 | read-only | The number of frame loss measurement packets sent in forward direction. |
| C64 zxAnCfm2MepLmFwdReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.8 | Counter64 | read-only | The number of frame loss measurement packets received in forward direction. |
| I32 zxAnCfm2MepLmFwdLossRatio | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.9 | Integer32 | read-only | The frame loss ratio in forward direction of the LM. |
| C64 zxAnCfm2MepLmBwdSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.10 | Counter64 | read-only | The number of frame loss measurement packets sent in backward direction. |
| C64 zxAnCfm2MepLmBwdReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.11 | Counter64 | read-only | The number of frame loss measurement packets received in backward direction. |
| I32 zxAnCfm2MepLmBwdLossRatio | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.12 | Integer32 | read-only | The frame loss ratio in backward direction of the LM. |
| zxAnCfm2MepSlmOperTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6 | not-accessible | The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending SLM . Steps to use entries in this table: 1) Wait for zxAnCfm2MepSlmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepSlmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepSlmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepSlmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepSlmEnable and other synthetic loss measurement objects (such as zxAnCfm2MepSlmPriority, ...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varbind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepSlmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepSlmEnable. When it is reset to false, the last SLM has been transmitted. 5) Get the results of the test from the zxAnCfm2MepSlmRltTable. | |
| zxAnCfm2MepSlmOperEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1 | not-accessible | The synthetic loss measurement table entry. | |
| I32 zxAnCfm2MepSlmTestId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.1 | Integer32 | not-accessible | The synthetic frame loss measurement identifier of the specified MEP. 8 measurements can be activated simultaneously on the MEP. |
| INT zxAnCfm2MepSlmEnable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.2 | INTEGER | read-create | Enable/disable the SLM function. If the value is disable the SLM test can not be started. |
| DOT zxAnCfm2MepSlmTargetMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.3 | Dot1agCfmMepIdOrZero | read-create | The Maintenance Association End Point Identifier of another MEP in the same Maintenance Association to which the SLM is to be sent. This variable will be used if the SLM destination MAC address type is unicast, if 0, the SLM destination MAC address type is multicast. |
| INT zxAnCfm2MepSlmAppType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.4 | INTEGER | read-create | The application type of the SLM. |
| INT zxAnCfm2MepSlmInterval | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.5 | INTEGER | read-create | The interval at which SLM is send by an MEP. Unlimited means the test can't stop until the user stops it. |
| I32 zxAnCfm2MepSlmDuration | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.6 | Integer32 | read-create | The duration of SLM test. |
| I32 zxAnCfm2MepSlmPriority | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.7 | Integer32 | read-create | The priority. 3 bit value to be used in the VLAN tag, if present in the SLM frame. |
| INT zxAnCfm2MepSlmFrameSize | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.8 | INTEGER | read-create | The packet length of the SLM frame. |
| INT zxAnCfm2MepSlmOperType | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.9 | INTEGER | read-create | The operation type of the SLM. |
| INT zxAnCfm2MepSlmResultOk | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.30 | INTEGER | read-only | The result of the operation: yes(1): The Synthetic Loss Measurement Message(s) will be (or has been) sent. no(2): The Synthetic Loss Measurement Message(s) will not be sent. |
| zxAnCfm2MepSlmRltTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7 | not-accessible | The synthetic frame loss measurement result table. | |
| zxAnCfm2MepSlmRltEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1 | not-accessible | The result information of Synthetic Loss Measurement. | |
| DOT zxAnCfm2SlmRemoteMepId | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.1 | Dot1agCfmMepId | not-accessible | Remote MEP identifier, which receives synthetic frame loss measurement packets and responses synthetic frame loss reply packets. |
| DAT zxAnCfm2MepSlmStartTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.2 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval. |
| DAT zxAnCfm2MepSlmEndTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.3 | DateAndTime | read-only | The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval. |
| I32 zxAnCfm2MepSlmElapsedTime | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.4 | Integer32 | read-only | The elapsed time of the measurement interval. |
| C32 zxAnCfm2MepSlmSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.5 | Counter32 | read-only | The number of synthetic loss measurement packets sent. |
| C32 zxAnCfm2MepSlmReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.6 | Counter32 | read-only | The number of synthetic loss measurement packets received. |
| C32 zxAnCfm2MepSlmFwdSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.7 | Counter32 | read-only | The number of synthetic loss measurement packets sent in forward direction. |
| C32 zxAnCfm2MepSlmFwdReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.8 | Counter32 | read-only | The number of synthetic loss measurement packets received in forward direction. |
| I32 zxAnCfm2MepSlmFwdLossPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.9 | Integer32 | read-only | The packets loss in the latest SLM in forward direction. |
| I32 zxAnCfm2MepSlmFwdLossRatio | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.10 | Integer32 | read-only | The packet loss ratio of the latest SLM in forward direction. |
| C32 zxAnCfm2MepSlmBwdSentPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.11 | Counter32 | read-only | The number of synthetic loss measurement packets sent in backward direction. |
| C32 zxAnCfm2MepSlmBwdReceivedPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.12 | Counter32 | read-only | The number of synthetic loss measurement packets received in backward direction. |
| I32 zxAnCfm2MepSlmBwdLossPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.13 | Integer32 | read-only | The packets loss of the latest SLM in backward direction. |
| I32 zxAnCfm2MepSlmBwdLossRatio | 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.14 | Integer32 | read-only | The packet loss ratio of the latest SLM in backward direction. |
| zxAnCfm2StatisticsObjects | 1.3.6.1.4.1.3902.1082.80.45.2.3.23 | |||
| zxAnCfm2MepStatsTable | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2 | not-accessible | The MEP (Maintenance Association End Point) statistics table. | |
| zxAnCfm2MepStatsEntry | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1 | not-accessible | The MEP statistics table entry. | |
| C64 zxAnCfm2MepStatsRxPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.1 | Counter64 | read-only | The total number of received CFM packets. |
| C64 zxAnCfm2MepStatsTxPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.2 | Counter64 | read-only | The total number of transmitted CFM packets. |
| C64 zxAnCfm2MepStatsRxSequenceErrors | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.3 | Counter64 | read-only | The total number of received out-of-sequence CFM packets. |
| C64 zxAnCfm2MepStatsRxSrcMacErrors | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.4 | Counter64 | read-only | The total number of received CFM packets that source MAC address is invalid. |
| C64 zxAnCfm2MepStatsRxCorrectPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.5 | Counter64 | read-only | The total number of received correct CFM packets. |
| C64 zxAnCfm2MepStatsRxIllegalPkts | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.6 | Counter64 | read-only | The total number of received illegal CFM packets. |
| INT zxAnCfm2MepStatsReset | 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.100 | INTEGER | read-write | Clear all the MEP statistics variables. When get this variable, always return 1. |
RFC description
Connectivity Fault Management module for managing Y.1731 on ZTE access nodes. Manages maintenance domains and connectivity testing.
Start monitoring ZTE access node, carrier Ethernet aggregation switch (802.1ag/Y.1731 MEP continuity-check/fault status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.