All MIBs › Wellfleet-FDDI-MIB
Category: Wellfleet BayNetworks LAN and Bridging
Description: Monitors Wellfleet FDDI ring status, station management parameters, and traffic counters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Wellfleet-FDDI-MIB?
This Wellfleet (Bay Networks) proprietary MIB monitors and configures FDDI (Fiber Distributed Data Interface) ring interfaces on legacy Wellfleet routers, covering ring/station management state and traffic counters. It exposes hardware/interface status data such as ring operational state (ring up/down, wrap condition), station management (SMT) parameters, and frame/error traffic counters specific to the token-passing FDDI ring. Monitoring this MIB is directly relevant to hardware/link health: ring state and station management counters reveal whether an FDDI ring is stable, has wrapped due to a break, or is experiencing beaconing/error conditions, classic FDDI fault indicators. It parallels the scope of the IETF standard FDDI-SMT-MIB (RFC 1512), implemented instead as a Wellfleet proprietary schema. It is deployed on legacy Wellfleet/Bay Networks routers connecting to FDDI backbone rings, common in early-1990s campus and metropolitan networks. Engineers can download the Wellfleet-FDDI-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-FDDI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Wellfleet/Bay Networks routers with FDDI ring interfaces
Monitoring Examples
No sample objects were provided for this module in the source data. In general, an FDDI MIB of this kind exposes ring operational state and SMT station parameters along with frame/error counters, which an operator would poll to detect a ring that has wrapped due to a fiber break or is beaconing, both signs of an FDDI segment fault requiring physical investigation.
What Can Be Monitored
- FDDI ring operational state
- ring wrap/beaconing condition
- station management (SMT) parameters
- FDDI frame/error traffic counters
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| TimeTicks |
From RFC1213-MIB
| DisplayString |
From Wellfleet-COMMON-MIB
| wfFddiGroup | OBJECT-IDENTITY |
| wfLine | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wfFddiTable | 1.3.6.1.4.1.18.3.4.4 | not-accessible | FDDI line record | |
| wfFddiEntry | 1.3.6.1.4.1.18.3.4.4.1 | not-accessible | An entry in the FDDI table | |
| INT wfFDDIDelete | 1.3.6.1.4.1.18.3.4.4.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFDDIEnable | 1.3.6.1.4.1.18.3.4.4.1.2 | INTEGER | read-write | Enable/disable parameter, default = enable. |
| INT wfFDDIState | 1.3.6.1.4.1.18.3.4.4.1.3 | INTEGER | read-only | Line driver state variable, not present, init, down, up. |
| INT wfFDDISlot | 1.3.6.1.4.1.18.3.4.4.1.4 | INTEGER | read-only | Instance ID slot - filled in by driver. |
| INT wfFDDINode | 1.3.6.1.4.1.18.3.4.4.1.5 | INTEGER | read-only | Instance ID node - filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'node'. Where 'module' is defined in attribute 50 and 'node' is defined in attribute 51 of this table. For non-ASN platforms this attribute indicates the physical node number on the slot |
| INT wfFDDICct | 1.3.6.1.4.1.18.3.4.4.1.6 | INTEGER | read-write | Cct number for this line instance. |
| INT wfFDDIBofl | 1.3.6.1.4.1.18.3.4.4.1.7 | INTEGER | read-write | The Breath-Of-Life (BOFL) function, when enabled, will disable the LLC interface when the FDDI becomes non-operational (i.e., link unavailable) and the following conditions are true: 1. The wfFddiMacMaUnitDataEnable attribute is enabled. 2. The BOFL timer expired (specified by wfFDDIBoflTmo). If this attribute is disabled, the LLC interface will be terminated immediately after the link becomes unavailable. |
| INT wfFDDIBoflTmo | 1.3.6.1.4.1.18.3.4.4.1.8 | INTEGER | read-write | Specifies the time value (in seconds) of the BOFL timer. The BOFL timer will be set to the value of this attribute when the following conditions are true: 1. The wfFDDIBofl attribute is enabled. 2. The link becomes unavailable. Upon expiration of the BOFL timer, the LLC interface will be disabled. Note also that the BOFL timer will be disabled if the link becomes operational (available) before the timer expires.. |
| INT wfFDDIMtu | 1.3.6.1.4.1.18.3.4.4.1.9 | INTEGER | read-only | The MTU is the maximum allowed frame length on the wire, excluding frame delimiters (i.e. preamble, ending delimiter). The MTU of an FDDI frame includes: FC (1 octet) + DA (6 octets) + SA (6 octets) + INFO (<= 4478 octets) + FCS (4 octets) = 4495 octets |
| OCT wfFDDIMadr | 1.3.6.1.4.1.18.3.4.4.1.10 | OCTET STRING | read-only | PROM-based MAC address, fixed - line driver fills in. |
| CTR wfFDDIOctetsRxOk | 1.3.6.1.4.1.18.3.4.4.1.11 | Counter | read-only | Number of bytes received without error. This byte count only includes LLC frames (i.e. no MAC and SMT frames). |
| CTR wfFDDIFramesRxOk | 1.3.6.1.4.1.18.3.4.4.1.12 | Counter | read-only | Number of frames received without error. This frame count only includes LLC frames (i.e. no MAC and SMT frames). |
| CTR wfFDDIOctetsTxOk | 1.3.6.1.4.1.18.3.4.4.1.13 | Counter | read-only | Number of bytes transmitted without error. This byte count only includes LLC and SMT frames (i.e. no MAC frames). |
| CTR wfFDDIFramesTxOk | 1.3.6.1.4.1.18.3.4.4.1.14 | Counter | read-only | Number of frames transmitted without error. This frame count only includes LLC and SMT frames (i.e. no MAC frames ). |
| CTR wfFDDICrcErrRx | 1.3.6.1.4.1.18.3.4.4.1.15 | Counter | read-only | Number of frames received with CRC errors. |
| CTR wfFDDIOverrunRx | 1.3.6.1.4.1.18.3.4.4.1.16 | Counter | read-only | Number of frames received with internal overrun errors. |
| CTR wfFDDIParityErrRx | 1.3.6.1.4.1.18.3.4.4.1.17 | Counter | read-only | Number of frames received with parity errors. |
| CTR wfFDDIMacErrRx | 1.3.6.1.4.1.18.3.4.4.1.18 | Counter | read-only | Number of frames received with MAC errors. |
| CTR wfFDDIRingErrRx | 1.3.6.1.4.1.18.3.4.4.1.19 | Counter | read-only | Number of receive ring error events. |
| CTR wfFDDISmtRingErrRx | 1.3.6.1.4.1.18.3.4.4.1.20 | Counter | read-only | Number of SMT receive ring error events. |
| CTR wfFDDIRingOverrunRx | 1.3.6.1.4.1.18.3.4.4.1.21 | Counter | read-only | Number of LLC receive ring overrun events. |
| CTR wfFDDISmtRingOverrunRx | 1.3.6.1.4.1.18.3.4.4.1.22 | Counter | read-only | Number of SMT receive ring overrun events. |
| CTR wfFDDIAbortTx | 1.3.6.1.4.1.18.3.4.4.1.23 | Counter | read-only | Number of transmit frames with internal abort errors. |
| CTR wfFDDIUnderrunTx | 1.3.6.1.4.1.18.3.4.4.1.24 | Counter | read-only | Number of transmit frames aborted with underrun errors. |
| CTR wfFDDIParityErrTx | 1.3.6.1.4.1.18.3.4.4.1.25 | Counter | read-only | Number of transmit frames aborted with parity errors. |
| CTR wfFDDIRingErrTx | 1.3.6.1.4.1.18.3.4.4.1.26 | Counter | read-only | Number of LLC/SMT transmit ring error events. |
| CTR wfFDDIPortOpErr | 1.3.6.1.4.1.18.3.4.4.1.27 | Counter | read-only | Number of port operation error events. |
| CTR wfFDDIInternOpErr | 1.3.6.1.4.1.18.3.4.4.1.28 | Counter | read-only | Number of internal operation error events. |
| CTR wfFDDIHostErr | 1.3.6.1.4.1.18.3.4.4.1.29 | Counter | read-only | Number of host error events. |
| INT wfFDDISmtConnectionPolicy | 1.3.6.1.4.1.18.3.4.4.1.30 | INTEGER | read-write | A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence. The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15 |
| INT wfFDDISmtTNotify | 1.3.6.1.4.1.18.3.4.4.1.31 | INTEGER | read-write | The timer used in the Neighbor Notification protocol, reported in seconds and ranging from 2 to 30 seconds. |
| INT wfFDDIMacTReq | 1.3.6.1.4.1.18.3.4.4.1.32 | INTEGER | read-write | Specifies the maximum time value of 'wfFddiPathMaxTReq' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiPathMaxTReq' is managed by setting this attribute. This attribute has the time value range of: wfFddiPathTvxLowerBound < wfFddiMacTReq <= wfFddiPathTMaxLowerBound. Time specified in octet units. The default value of this attribute is 165 msec. The name of this attribute in the IETF MIB is FddiMibPATHMaxTReq. To convert 165 milliseconds to octet units of 80 nanaseconds: T_Req Nanaoseconds = ((165 * 1000 * 1000) / 80) = 2062500 To convert 2062500 octet units of 80 nanoseconds to milliseconds: T_Req Milliseconds = ((2062500 / 12.5) / 1000) = 165 |
| INT wfFDDIMacTMax | 1.3.6.1.4.1.18.3.4.4.1.33 | INTEGER | read-only | The requested maximum TTRT to be supported by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| INT wfFDDIMacTvxValue | 1.3.6.1.4.1.18.3.4.4.1.34 | INTEGER | read-only | The requested value of TvxValue represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| INT wfFDDIMacTMin | 1.3.6.1.4.1.18.3.4.4.1.35 | INTEGER | read-only | The requested minimum TTRT to be requested by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| INT wfFDDIHardwareFilter | 1.3.6.1.4.1.18.3.4.4.1.36 | INTEGER | read-write | Hardware filter (CAM) parameter. |
| INT wfFDDISmtEnable | 1.3.6.1.4.1.18.3.4.4.1.37 | INTEGER | read-write | Enable Station Management periodic timer and NIF protocol. |
| INT wfFDDITxQueueLength | 1.3.6.1.4.1.18.3.4.4.1.38 | INTEGER | read-only | Current Transmit Queue Length |
| INT wfFDDIRxQueueLength | 1.3.6.1.4.1.18.3.4.4.1.39 | INTEGER | read-only | Current Receive Queue Length |
| CTR wfFDDITxClipFrames | 1.3.6.1.4.1.18.3.4.4.1.40 | Counter | read-only | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| CTR wfFDDIRxReplenMisses | 1.3.6.1.4.1.18.3.4.4.1.41 | Counter | read-only | Number of packet buffer misses while attempting to replenish driver receive ring. |
| INT wfFDDICfgTxQueueLength | 1.3.6.1.4.1.18.3.4.4.1.42 | INTEGER | read-write | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. |
| INT wfFDDICfgRxQueueLength | 1.3.6.1.4.1.18.3.4.4.1.43 | INTEGER | read-write | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero cuases router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. |
| INT wfFDDILineNumber | 1.3.6.1.4.1.18.3.4.4.1.44 | INTEGER | read-write | Logical line number associated with this driver entity. |
| INT wfFDDIForcePeerTree | 1.3.6.1.4.1.18.3.4.4.1.45 | INTEGER | read-write | This attribute allows all FDDI Peer/Tree connections to reach the 'Thru' state. This is done to give the user some flexibility and allow them to Daisy Chain their Phy connections, mixing Tree & Peer connections. This type of daisy chaining DOES NOT conform to the SMT standard and is NOT recommended as it may result in a less than optimum token path. Normally when we have a Peer/Tree connection mix, we will wrap the connection, favoring PHY B. |
| CTR wfFDDIInvalidFrameStatusRx | 1.3.6.1.4.1.18.3.4.4.1.46 | Counter | read-only | A count of the number of badly formed frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 control indicator symbols (i.e. E, A, C, flags). |
| CTR wfFDDIRxOversizedFrames | 1.3.6.1.4.1.18.3.4.4.1.47 | Counter | read-only | Number of LLC frames received whose length exceeded the MTU. |
| CTR wfFDDIRxSmtOversizedFrames | 1.3.6.1.4.1.18.3.4.4.1.48 | Counter | read-only | Number of SMT frames received whose length exceeded the MTU. |
| CTR wfFDDIRxUndersizedFrames | 1.3.6.1.4.1.18.3.4.4.1.49 | Counter | read-only | Number of LLC frames received whose length was less than 20 bytes including the FC byte and a 4 byte CRC. |
| CTR wfFDDIRxSmtUndersizedFrames | 1.3.6.1.4.1.18.3.4.4.1.50 | Counter | read-only | Number of SMT frames received whose length was less than 37 bytes including the FC byte and a 4 byte CRC. |
| INT wfFDDIModule | 1.3.6.1.4.1.18.3.4.4.1.51 | INTEGER | read-only | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| INT wfFDDIActualNode | 1.3.6.1.4.1.18.3.4.4.1.52 | INTEGER | read-only | Actual Node number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| TIK wfFDDILastChange | 1.3.6.1.4.1.18.3.4.4.1.53 | TimeTicks | read-only | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second) since the network management portion of the system was last re-initialized. Usually the time since boot. |
| GAU wfFDDIOutQLen | 1.3.6.1.4.1.18.3.4.4.1.54 | Gauge | read-only | The instantaneous current length of the output packet queue (in packets). |
| CTR wfFDDIRxSmtOctets | 1.3.6.1.4.1.18.3.4.4.1.55 | Counter | read-only | Number of bytes received without error. This byte count only includes SMT frames (i.e. no MAC and LLC frames). |
| CTR wfFDDIRxSmtFrames | 1.3.6.1.4.1.18.3.4.4.1.56 | Counter | read-only | Number of frames received without error. This frame count only includes SMT frames (i.e. no MAC and LLC frames). |
| CTR wfFDDIIntProcessings | 1.3.6.1.4.1.18.3.4.4.1.57 | Counter | read-only | Counts the number of times the interrupt service routine has been called |
| CTR wfFDDITxProcessings | 1.3.6.1.4.1.18.3.4.4.1.58 | Counter | read-only | Counts the number of times the transmit routine fsi_xmt_oper_act(), has been called |
| CTR wfFDDIRxProcessings | 1.3.6.1.4.1.18.3.4.4.1.59 | Counter | read-only | Counts the number of times RINT processing takes place in the interrupt service routine. |
| CTR wfFDDITxRNRProcessings | 1.3.6.1.4.1.18.3.4.4.1.60 | Counter | read-only | Counts the number of times the transmit complete routine fsi_xmt_cmpl(), has been called |
| CTR wfFDDISmtRxProcessings | 1.3.6.1.4.1.18.3.4.4.1.61 | Counter | read-only | Counts the number of time RINT was processing was performed on the SMT receive ring. |
| INT wfFDDIPhyALogPtr | 1.3.6.1.4.1.18.3.4.4.1.62 | INTEGER | read-only | Address of the Debug Phy Event Buffer for Phy A. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| INT wfFDDIPhyBLogPtr | 1.3.6.1.4.1.18.3.4.4.1.63 | INTEGER | read-only | Address of the Debug Phy Event Buffer for Phy B. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| INT wfFDDIPromiscuous | 1.3.6.1.4.1.18.3.4.4.1.64 | INTEGER | read-write | For now this attribute is used only in BNX code !!! The promiscuous parameter allows address filtering based on the destination MAC addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address and any functional group address are received. |
| INT wfFDDILLCFrameControl | 1.3.6.1.4.1.18.3.4.4.1.65 | INTEGER | read-write | Frame control used for LLC frames, using synchronous frames for reserved priority traffic when specified. |
| INT wfFDDITurboBofl | 1.3.6.1.4.1.18.3.4.4.1.66 | INTEGER | read-write | DEBUG parameter - Turbo bofl enabled or disabled, by adjusting BoflNum and BoflLen bofl packets can be made to fill the links available bandwith. This function is not a faster parallel of the wfFDDIBofl feature it does not opperate on a disabled LLC interface |
| INT wfFDDIBoflNum | 1.3.6.1.4.1.18.3.4.4.1.67 | INTEGER | read-write | DEBUG parameter - Number of breath of life packets per breath of life |
| INT wfFDDIBoflLen | 1.3.6.1.4.1.18.3.4.4.1.68 | INTEGER | read-write | DEBUG parameter - breath of life packet length |
| wfFddiSmtGroup | 1.3.6.1.4.1.18.3.4.15.1 | |||
| wfFddiSmtTable | 1.3.6.1.4.1.18.3.4.15.1.2 | not-accessible | A list of SMT entries. | |
| wfFddiSmtEntry | 1.3.6.1.4.1.18.3.4.15.1.2.1 | not-accessible | A SMT entry containing information common to a given SMT. | |
| INT wfFddiSmtSlot | 1.3.6.1.4.1.18.3.4.15.1.2.1.1 | INTEGER | read-only | Slot number associated with an SMT entity. |
| INT wfFddiSmtNode | 1.3.6.1.4.1.18.3.4.15.1.2.1.2 | INTEGER | read-only | Node/connector number associated with an SMT entity. |
| INT wfFddiSmtCct | 1.3.6.1.4.1.18.3.4.15.1.2.1.3 | INTEGER | read-only | Circuit number associated with an SMT entity. |
| OCT wfFddiSmtStationId | 1.3.6.1.4.1.18.3.4.15.1.2.1.4 | OCTET STRING | read-only | Unique identifier of an FDDI station. |
| INT wfFddiSmtOpVersionId | 1.3.6.1.4.1.18.3.4.15.1.2.1.5 | INTEGER | read-only | The version that this station is using for its operation. |
| INT wfFddiSmtMacCt | 1.3.6.1.4.1.18.3.4.15.1.2.1.6 | INTEGER | read-only | The number of MACs in a station. |
| INT wfFddiSmtNonMasterCt | 1.3.6.1.4.1.18.3.4.15.1.2.1.7 | INTEGER | read-only | The number of non master ports (A, B, or S PORTs) in a station. |
| INT wfFddiSmtEcmState | 1.3.6.1.4.1.18.3.4.15.1.2.1.8 | INTEGER | read-only | Indicates the current state of the ECM state machine. |
| INT wfFddiSmtCfState | 1.3.6.1.4.1.18.3.4.15.1.2.1.9 | INTEGER | read-only | The attachment configuration for a station. |
| INT wfFddiSmtBypassPresent | 1.3.6.1.4.1.18.3.4.15.1.2.1.10 | INTEGER | read-only | A flag indicating if the station has an optical bypass on its A/B port pair. |
| INT wfFddiSmtRemoteDisconnectFlag | 1.3.6.1.4.1.18.3.4.15.1.2.1.11 | INTEGER | read-only | A flag indicating that the station was remotely disconnected from the network as a result of receiving an 'wfFddiSmtStationAction' disconnect in a Parameter Management Frame. A station requires a Connect Action to rejoin & clear the flag. |
| INT wfFddiSmtStationStatus | 1.3.6.1.4.1.18.3.4.15.1.2.1.12 | INTEGER | read-only | This variable indicates the current state of the primary and secondary paths within this station. |
| INT wfFddiSmtPeerWrapFlag | 1.3.6.1.4.1.18.3.4.15.1.2.1.13 | INTEGER | read-only | This variable assumes the value of the 'PeerWrapFlag' in CFM. |
| wfFddiSmtExtTable | 1.3.6.1.4.1.18.3.4.15.1.3 | not-accessible | A list of SMT extension entries. | |
| wfFddiSmtExtEntry | 1.3.6.1.4.1.18.3.4.15.1.3.1 | not-accessible | A SMT entry containing information common to a given SMT. | |
| INT wfFddiSmtDelete | 1.3.6.1.4.1.18.3.4.15.1.3.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiSmtExtSlot | 1.3.6.1.4.1.18.3.4.15.1.3.1.2 | INTEGER | read-only | Slot number associated with an SMT entity. |
| INT wfFddiSmtExtNode | 1.3.6.1.4.1.18.3.4.15.1.3.1.3 | INTEGER | read-only | Node/connector number associated with an SMT entity. |
| INT wfFddiSmtExtCct | 1.3.6.1.4.1.18.3.4.15.1.3.1.4 | INTEGER | read-only | Circuit number associated with an SMT entity. |
| INT wfFddiSmtHiVersionId | 1.3.6.1.4.1.18.3.4.15.1.3.1.5 | INTEGER | read-only | The highest version of SMT that this station supports. |
| INT wfFddiSmtLoVersionId | 1.3.6.1.4.1.18.3.4.15.1.3.1.6 | INTEGER | read-only | The lowest version of SMT that this station supports. |
| OCT wfFddiSmtManufacturerData | 1.3.6.1.4.1.18.3.4.15.1.3.1.7 | OCTET STRING | read-only | Contains 32 Octets of manufacturer data. The first component, manufacturing OUI, is the 3 octet Organizationally Unique Identifier (OUI) assigned by IEEE. The second component, ManufacturerData, is the manufacturers data (29 octets). |
| STR wfFddiSmtUserData | 1.3.6.1.4.1.18.3.4.15.1.3.1.8 | DisplayString | read-write | Contains 32 Octets of user defined information in ascii format. |
| INT wfFddiSmtMibVersionId | 1.3.6.1.4.1.18.3.4.15.1.3.1.9 | INTEGER | read-only | The version of the FDDI MIB of this station. |
| INT wfFddiSmtMasterCts | 1.3.6.1.4.1.18.3.4.15.1.3.1.10 | INTEGER | read-only | The number of M ports in a node. |
| INT wfFddiSmtAvailablePaths | 1.3.6.1.4.1.18.3.4.15.1.3.1.11 | INTEGER | read-only | A bit string that indicates the path types that are available in the station. The value initially takes the value 0, then for each type of path that this node has available, 2 raised to a power is added to the sum. The powers are according to the following table: Path Power ---- ----- Primary 0 Secondary 1 Local 2 For example, a station having Primary and Local paths available would have a value of 5 (2**0 + 2**2). |
| INT wfFddiSmtConfigCapabilities | 1.3.6.1.4.1.18.3.4.15.1.3.1.12 | INTEGER | read-only | A bit string which indicates the configuration capabilities of a node. The 'Hold Available' bit indicates the support of the optional Hold function, which is controlled by 'wfFddiSmtConfigPolicy'. The 'CF-Wrap-AB' bit indicates that the station has the capability of performing a wrab_ab. The value is a sum. This value initially takes the value 0, then for each of the configuration policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power ------ ----- HoldAvailable 0 CF_Wrap-AB 1 |
| INT wfFddiSmtConfigPolicy | 1.3.6.1.4.1.18.3.4.15.1.3.1.13 | INTEGER | read-only | A bit string representing the configuration policies currently desired in a node. 'Hold' is one of the terms used for the 'Hold' flag. |
| INT wfFddiSmtStatRptPolicy | 1.3.6.1.4.1.18.3.4.15.1.3.1.14 | INTEGER | read-write | If ENABLED, indicates that the node will generate Status Report Frames (SRF) for its implemented events. |
| INT wfFddiSmtTraceMaxExpiration | 1.3.6.1.4.1.18.3.4.15.1.3.1.15 | INTEGER | read-write | Maximum propogation time for a Trace on an FDDI topology. The value is stored in milliseconds. |
| OCT wfFddiSmtTimeStamp | 1.3.6.1.4.1.18.3.4.15.1.3.1.16 | OCTET STRING | read-only | Holds the time of creation of the last Status Report Frame (SRF). |
| OCT wfFddiSmtTransitionTimeStamp | 1.3.6.1.4.1.18.3.4.15.1.3.1.17 | OCTET STRING | read-only | Holds the time of occurrence of the last condition or event. |
| INT wfFddiSmtDatProtocol | 1.3.6.1.4.1.18.3.4.15.1.3.1.18 | INTEGER | read-write | SMT will implement an optional ANSI duplicate address test involving periodic transmission of NSA NIF frames addressed to itself if enabled by this attribute. |
| wfFddiSmtActionTable | 1.3.6.1.4.1.18.3.4.15.1.4 | not-accessible | A list of SMT action entries. | |
| wfFddiSmtActionEntry | 1.3.6.1.4.1.18.3.4.15.1.4.1 | not-accessible | An SMT entry containing actions common to a given SMT. | |
| INT wfFddiSmtActionDelete | 1.3.6.1.4.1.18.3.4.15.1.4.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiSmtActionSlot | 1.3.6.1.4.1.18.3.4.15.1.4.1.2 | INTEGER | read-only | Slot number associated with an SMT action entity. |
| INT wfFddiSmtActionNode | 1.3.6.1.4.1.18.3.4.15.1.4.1.3 | INTEGER | read-only | Node/connector number associated with an SMT action entity. |
| INT wfFddiSmtActionCct | 1.3.6.1.4.1.18.3.4.15.1.4.1.4 | INTEGER | read-only | Circuit number associated with an SMT action entity. |
| INT wfFddiSmtStationAction | 1.3.6.1.4.1.18.3.4.15.1.4.1.5 | INTEGER | read-write | This object when read, always returns a value of other(1). The behavior of setting this variable to each of the acceptable values is as follows: Other: Results in a BadValue error Connect: Generates a connect signal to ECM to begin a connection sequence. The 'wfFddiSmtRemoteDisconnectFlag' is cleared on the setting of this variable to 1. Disconnect: Generates a disconnect signal to ECM and sets the 'wfFddiSmtRemoteDisconnectFlag' to TRUE. Path_Test: Initiates a station path test. The 'PathTest' variable is set to 'Testing'. The results of this action are not specified in the standard. Self_test: Initiates a station self test. The results of this action are not specified in the standard. Disable_A: Disable_A causes a PC_Disable on the A port if the A port mode is peer. Disable_B: Disable_B causes a PC_Disable on the B port if the B port mode is peer. Disable_M: Disable_M causes a PC_Disable on all M ports. Attempts to set this object to all other values results in a BadValue error. Agents may elect to return a BadValue error on attempts to set this variable to PathTest or SelfTest. |
| wfFddiMacGroup | 1.3.6.1.4.1.18.3.4.15.2 | |||
| wfFddiMacTable | 1.3.6.1.4.1.18.3.4.15.2.2 | not-accessible | A list of MAC entries. | |
| wfFddiMacEntry | 1.3.6.1.4.1.18.3.4.15.2.2.1 | not-accessible | A MAC entry containing information common to a given MAC. | |
| INT wfFddiMacSlot | 1.3.6.1.4.1.18.3.4.15.2.2.1.1 | INTEGER | read-only | Slot number associated with a MAC entity. |
| INT wfFddiMacNode | 1.3.6.1.4.1.18.3.4.15.2.2.1.2 | INTEGER | read-only | Node/connector number associated with a MAC entity. |
| INT wfFddiMacCct | 1.3.6.1.4.1.18.3.4.15.2.2.1.3 | INTEGER | read-only | Circuit number associated with a MAC entity. |
| OCT wfFddiMacUpstreamNbr | 1.3.6.1.4.1.18.3.4.15.2.2.1.4 | OCTET STRING | read-only | The MAC's upstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown. SMT uses the MSB form for representation of 48-bit addresses. |
| OCT wfFddiMacDownstreamNbr | 1.3.6.1.4.1.18.3.4.15.2.2.1.5 | OCTET STRING | read-only | The MAC's downstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown. SMT uses the MSB form for representation of 48-bit addresses. |
| OCT wfFddiMacSmtAddress | 1.3.6.1.4.1.18.3.4.15.2.2.1.6 | OCTET STRING | read-only | The 48 bit individual address of the MAC used for SMT frames. SMT uses the MSB form for representation of 48-bit addresses. |
| INT wfFddiMacTNeg | 1.3.6.1.4.1.18.3.4.15.2.2.1.7 | INTEGER | read-only | The negotiated TTRT during the claim process represented as an unsigned integer specifying time in nanoseconds. |
| INT wfFddiMacRmtState | 1.3.6.1.4.1.18.3.4.15.2.2.1.8 | INTEGER | read-only | Indicates the current state of the Ring Management state machine. |
| OCT wfFddiMacOldUpstreamNbr | 1.3.6.1.4.1.18.3.4.15.2.2.1.9 | OCTET STRING | read-only | The previous value of the MAC's upstream neighbor's long individual MAC address. It has an initial value of the SMT-Unknown-MAC Address and is only modified as specified by the Neighbor Information Frame protocol. SMT uses the MSB form for representation of 48-bit addresses. |
| OCT wfFddiMacOldDownstreamNbr | 1.3.6.1.4.1.18.3.4.15.2.2.1.10 | OCTET STRING | read-only | The previous value of the MAC's downstream neighbor's long individual MAC address. It has an initial value of the SMT-Unknown-MAC Address and is only modified as specified by the Neighbor Information Frame protocol. SMT uses the MSB form for representation of 48-bit addresses. |
| OCT wfFddiMacTokenCts | 1.3.6.1.4.1.18.3.4.15.2.2.1.11 | OCTET STRING | read-only | A count that should as closely as possible match the number of times the station has received a token (total of non-restricted and restricted) on this MAC. This count is valuable for determination of network load. |
| OCT wfFddiMacErrorCts | 1.3.6.1.4.1.18.3.4.15.2.2.1.12 | OCTET STRING | read-only | A count of the number of frames that were detected in error by this MAC that had not been detected in error by another MAC. |
| OCT wfFddiMacLostCts | 1.3.6.1.4.1.18.3.4.15.2.2.1.13 | OCTET STRING | read-only | A count of the number of instances that this MAC detected a format error during frame reception such that the frame was stripped. |
| INT wfFddiMacDaFlag | 1.3.6.1.4.1.18.3.4.15.2.2.1.14 | INTEGER | read-only | Duplicate Address Flag. An RMT flag used to indicate that the MAC under control has the same address as another MAC on the FDDI. |
| INT wfFddiMacUnaDaFlag | 1.3.6.1.4.1.18.3.4.15.2.2.1.15 | INTEGER | read-only | A flag, UNDA_Flag, set when the upstream neighbor reports a duplicate address condition. Cleared once the condition clears. |
| INT wfFddiMacFrameErrorFlag | 1.3.6.1.4.1.18.3.4.15.2.2.1.16 | INTEGER | read-only | Indicates the MAC Frame Error Condition is present when set. Cleared when the condition clears and on station initialization. |
| INT wfFddiMacMaUnitDataAvailable | 1.3.6.1.4.1.18.3.4.15.2.2.1.17 | INTEGER | read-only | A flag indicating that the MAC is available for the transmission and reception of Protocol Data Units (PDUs). The MAC and LLC interface will be established when the wfFddiMacMaUnitDataEnable attribute is enabled. |
| INT wfFddiMacDownstreamPortType | 1.3.6.1.4.1.18.3.4.15.2.2.1.18 | INTEGER | read-only | Indicates the PC-Type of the first port that is downstream of this MAC (the exit port). |
| wfFddiMacExtTable | 1.3.6.1.4.1.18.3.4.15.2.3 | not-accessible | A list of MAC extension entries. | |
| wfFddiMacExtEntry | 1.3.6.1.4.1.18.3.4.15.2.3.1 | not-accessible | A MAC entry containing information common to a given MAC. | |
| INT wfFddiMacDelete | 1.3.6.1.4.1.18.3.4.15.2.3.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiMacExtSlot | 1.3.6.1.4.1.18.3.4.15.2.3.1.2 | INTEGER | read-only | Slot number associated with a MAC entity. |
| INT wfFddiMacExtNode | 1.3.6.1.4.1.18.3.4.15.2.3.1.3 | INTEGER | read-only | Node/connector number associated with a MAC entity. |
| INT wfFddiMacExtCct | 1.3.6.1.4.1.18.3.4.15.2.3.1.4 | INTEGER | read-only | Circuit number associated with a MAC entity. |
| INT wfFddiMacFrameStatusFunctions | 1.3.6.1.4.1.18.3.4.15.2.3.1.5 | INTEGER | read-only | Indicates the MAC's optional Frame Status processing functions. The value is a sum. This value initially takes the value 0, then for each function present, 2 raised to a power is added to the sum. The powers are according to the following table: function power -------- ----- fs-repeating 0 fs-setting 1 fs-clearing 2 |
| INT wfFddiMacBridgeFunctions | 1.3.6.1.4.1.18.3.4.15.2.3.1.6 | INTEGER | read-only | Indicates the MAC's optional bridging functions. The value is a sum. This value initially takes the value zero, then for each function present, 2 raised to a power is added to the sum. The powers are according to the following table: Function Power -------- ---- tb 0 -- Transparent bridging active sr 1 -- Src routing active srt 2 -- Src routing transparent active |
| INT wfFddiMacTMaxCapability | 1.3.6.1.4.1.18.3.4.15.2.3.1.7 | INTEGER | read-only | Indicates the maximum time value (in nanoseconds) of 'wfFddiMacTMax' that this MAC can support. |
| INT wfFddiMacTvxCapability | 1.3.6.1.4.1.18.3.4.15.2.3.1.8 | INTEGER | read-only | Indicates the maximum time value (in nanoseconds) of 'wfFddiMacTvxValue' that this MAC can support. |
| INT wfFddiMacAvailablePaths | 1.3.6.1.4.1.18.3.4.15.2.3.1.9 | INTEGER | read-only | Indicates the paths available for this MAC. The value is a sum. This value initially takes the value 0, then for each type of PATH that this MAC has available, 2 raised to a power is added to the sum. The powers are according to the following table: Path Power ---- ----- Primary 0 Secondary 1 Local 2 |
| INT wfFddiMacCurrentPath | 1.3.6.1.4.1.18.3.4.15.2.3.1.10 | INTEGER | read-only | Indicates the Path into which this MAC is currently inserted. |
| INT wfFddiMacDupAddrTest | 1.3.6.1.4.1.18.3.4.15.2.3.1.11 | INTEGER | read-only | The Duplicate Address test flag. |
| INT wfFddiMacRequestedPaths | 1.3.6.1.4.1.18.3.4.15.2.3.1.12 | INTEGER | read-only | Contains a list of Permitted Paths which specifies the Path(s) into which the MAC may be inserted. The value is a sum which represents the individual paths that are desired. This value initially takes the value zero, then for each type of PATH that this node is, 2 raised to a power is added to the sum. The powers are according to the following table: Path Power ---- ----- local 0 secondary-alternate 1 primary-alternate 2 concatenated-alternate 3 secondary-preferred 4 primary-preferred 5 concatenated-preferred 6 thru 7 |
| CTR wfFddiMacCopiedCts | 1.3.6.1.4.1.18.3.4.15.2.3.1.13 | Counter | read-only | A count that should as closely as possible match the number of frames addressed to (A bit set) and successfully copied into the station's receive buffers (C bit set) by this MAC. |
| INT wfFddiMacFrameErrorThreshold | 1.3.6.1.4.1.18.3.4.15.2.3.1.14 | INTEGER | read-write | Specifies the Mac Frame Error Threshold for determining when a MAC Frame Error Condition report will be generated (via an SRF Frame). If Mac Frame Error Ratio is greater than Mac Frame Error Threshold then the Mac Frame Error Condition exists. This Mac Frame Error Ratio is calculated periodically based on the attributes wfFddiMacErrorCts and wfFddiMacLostCts. A low value of Mac Frame Error Threshold will generate more frequent Mac Frame Error conditions if the wfFddiMacErrorCts and wfFddiMacLostCts counters are periodically increased. Therefore the user should set the Mac Frame Error Threshold (1..65535) in accordance with the volatility of the ring. |
| INT wfFddiMacFrameErrorRatio | 1.3.6.1.4.1.18.3.4.15.2.3.1.15 | INTEGER | read-only | This variable is the value of the ratio: ((delta wfFddiMacLostCts + delta wfFddiMacErrorCts) / (delta wfFddiMacFrameCts + delta wfFddiMacLostCts)) 2**16) |
| INT wfFddiMacHardwarePresent | 1.3.6.1.4.1.18.3.4.15.2.3.1.16 | INTEGER | read-only | This variable indicates the presence of underlying hardware support for this MAC object. |
| INT wfFddiMacMaUnitDataEnable | 1.3.6.1.4.1.18.3.4.15.2.3.1.17 | INTEGER | read-write | A configurable attribute that specifies whether the MAC will be available for the transmission and reception of Protocol Data Units (PDUs). If enabled, the interface to the MAC entity will be available for the exchange of PDUs between the MAC and the local LLC entity when the ring becomes operational (i.e., LLC interface is established). Setting this attribute has no effect on the transfer and reception of MAC or SMT frames. |
| CTR wfFddiMacTvxExpiredCts | 1.3.6.1.4.1.18.3.4.15.2.3.1.18 | Counter | read-only | A count that should as closely as possible match the number of times that TVX has expired. |
| CTR wfFddiMacLateCts | 1.3.6.1.4.1.18.3.4.15.2.3.1.19 | Counter | read-only | A count that should as closely as possible match the number of TRT expirations since this MAC was reset or a token was received. |
| CTR wfFddiMacRingOpCts | 1.3.6.1.4.1.18.3.4.15.2.3.1.20 | Counter | read-only | The count of the number of times the ring has entered the 'Ring Operational' state from the `Ring Not Operational' state. This count is updated when a SM_MA_STATUS Indication of a change in the Ring_Operational state occurs. Because of implementatio considerations, this count may be less than the actual RingOp_Ct. It is not a requirement that this count be exact. |
| CTR wfFddiMacDuplicateTokenCts | 1.3.6.1.4.1.18.3.4.15.2.3.1.21 | Counter | read-only | The count of the number of times a Duplicate Token has been detected. |
| wfFddiPathGroup | 1.3.6.1.4.1.18.3.4.15.3 | |||
| wfFddiPathTable | 1.3.6.1.4.1.18.3.4.15.3.2 | not-accessible | A list of PATH entries. | |
| wfFddiPathEntry | 1.3.6.1.4.1.18.3.4.15.3.2.1 | not-accessible | A PATH entry containing information common to a given PATH. | |
| INT wfFddiPathSlot | 1.3.6.1.4.1.18.3.4.15.3.2.1.1 | INTEGER | read-only | Slot number associated with a PATH entity. |
| INT wfFddiPathNode | 1.3.6.1.4.1.18.3.4.15.3.2.1.2 | INTEGER | read-only | Node/connector number associated with a PATH entity. |
| INT wfFddiPathCct | 1.3.6.1.4.1.18.3.4.15.3.2.1.3 | INTEGER | read-only | Circuit number associated with a PATH entity. |
| OCT wfFddiPathConfiguration | 1.3.6.1.4.1.18.3.4.15.3.2.1.4 | OCTET STRING | read-only | A circular list of resources on the path where each entry in the list consists of a resource type identifier (MAC or PORT), an index, and its CurrentPath. If the path is available to a resource in the node (as indicated by 'wfFddiPortAvailablePaths' or 'wfFddiMacAvailablePaths') then that resource shall be included in the list. If the path is not available to a resource or the underlying hardware is not present, then that resource shall not be included in the list. Resources currently inserted in the Path shall appear in the list once in token order. Resources not currently inserted in the Path shall appear once in any position supported by the implementation. |
| wfFddiPathExtTable | 1.3.6.1.4.1.18.3.4.15.3.3 | not-accessible | A list of PATH extension entries. | |
| wfFddiPathExtEntry | 1.3.6.1.4.1.18.3.4.15.3.3.1 | not-accessible | A PATH entry containing information common to a given PATH. | |
| INT wfFddiPathDelete | 1.3.6.1.4.1.18.3.4.15.3.3.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiPathExtSlot | 1.3.6.1.4.1.18.3.4.15.3.3.1.2 | INTEGER | read-only | Slot number associated with a Path entity. |
| INT wfFddiPathExtNode | 1.3.6.1.4.1.18.3.4.15.3.3.1.3 | INTEGER | read-only | Node/connector number associated with a Path entity. |
| INT wfFddiPathExtCct | 1.3.6.1.4.1.18.3.4.15.3.3.1.4 | INTEGER | read-only | Circuit number associated with a Path entity. |
| INT wfFddiPathTvxLowerBound | 1.3.6.1.4.1.18.3.4.15.3.3.1.5 | INTEGER | read-write | Specifies the minimum time value of 'wfFddiMacTvxValue' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiMacTvxValue' is managed by setting this variable. This variable has the time value range of: 0 < wfFddiPathTvxLowerBound < wfFddiPathMaxTReq Changes to this attribute shall either satisfy the time value relationship: wfFddiPathTvxLowerBound <= wfFddiMacTvxCapability of each of the MACS currently on the path, or be considered out of range. Time specified in nanoseconds. The initial value of wfFddiPathTvxLowerBound shall be 2.500 msec. |
| INT wfFddiPathTMaxLowerBound | 1.3.6.1.4.1.18.3.4.15.3.3.1.6 | INTEGER | read-write | Specifies the minimum time value of 'wfFddiMACTMax' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiMacTMax' is managed by setting this attribute. This attribute has the time value range of: wfFddiPathMaxTReq <= wfFddiPathTMaxLowerBound and an absolute time value range of 10msec <= wfFddiPathTMaxLowerBound. Changes to this aattribute shall either satisfy the time value relationship: wfFddiPathTMaxLowerBound < wfFddiMacTMaxCapability of each of the MACs currently on the path, or be considered out of range. Time specified in nanoseconds. The initial value of wfFddiPathTMaxLowerBound shall be 165 msec. |
| INT wfFddiPathMaxTReq | 1.3.6.1.4.1.18.3.4.15.3.3.1.7 | INTEGER | read-only | This variable is the T_Req_value passed to the MAC. Without having detected a duplicate, the time value of this variable shall assume the maximum supported time value which is less than or equal to the time value of wfFDDIMacTReq. When a MAC has an address detected as a duplicate, it may use a time value for this variable greater than the time value of wfFddiPathTMaxLowerBound. A station shall cause claim when the new T_Req may cause the value of T_Neg to change in the claim process (i.e., time value new T_Req < T_Neg, or old T_Req = T_Neg). This value is encoded in nanoseconds. The name of this attribute in the IETF MIB is FddiMibMACTReq. |
| wfFddiPortGroup | 1.3.6.1.4.1.18.3.4.15.4 | |||
| wfFddiPortTable | 1.3.6.1.4.1.18.3.4.15.4.2 | not-accessible | A list of PORT entries. | |
| wfFddiPortEntry | 1.3.6.1.4.1.18.3.4.15.4.2.1 | not-accessible | A PORT entry containing information common to a given PORT. | |
| INT wfFddiPortSlot | 1.3.6.1.4.1.18.3.4.15.4.2.1.1 | INTEGER | read-only | Slot number associated with a PORT entity. |
| INT wfFddiPortNode | 1.3.6.1.4.1.18.3.4.15.4.2.1.2 | INTEGER | read-only | Node/connector number associated with a PORT entity. |
| INT wfFddiPortCct | 1.3.6.1.4.1.18.3.4.15.4.2.1.3 | INTEGER | read-only | Circuit number associated with a PORT entity. |
| INT wfFddiPortIndex | 1.3.6.1.4.1.18.3.4.15.4.2.1.4 | INTEGER | read-only | A unique value for each PORT associated with each slot/connector pair. |
| INT wfFddiPortPcType | 1.3.6.1.4.1.18.3.4.15.4.2.1.5 | INTEGER | read-only | The physical connector type of the local PORT. |
| INT wfFddiPortPcNeighbor | 1.3.6.1.4.1.18.3.4.15.4.2.1.6 | INTEGER | read-only | The physical connector type of the remote PORT. |
| INT wfFddiPortPcmState | 1.3.6.1.4.1.18.3.4.15.4.2.1.7 | INTEGER | read-only | State of Physical State Machine. |
| INT wfFddiPortRequestedPaths | 1.3.6.1.4.1.18.3.4.15.4.2.1.8 | INTEGER | read-only | This variable is a list of permitted paths where each list element defines the Port's permitted paths. The first octet corresponds to 'none', the second octet to 'tree' and the third octet to 'peer'. |
| INT wfFddiPortBsFlag | 1.3.6.1.4.1.18.3.4.15.4.2.1.9 | INTEGER | read-only | Break State Flag - A PCM flag used to indicate that the PCM state Machine is not leaving the Break State in an expected time interval & a problem is suspected. |
| INT wfFddiPortLerFlag | 1.3.6.1.4.1.18.3.4.15.4.2.1.10 | INTEGER | read-only | The condition becomes active when the value of 'wfFddiPortLerEstimate' is <= 'wfFddiPortLerAlarm'. This will be reported with Status Report Frames (SRF). |
| INT wfFddiPortConnectState | 1.3.6.1.4.1.18.3.4.15.4.2.1.11 | INTEGER | read-only | A variable from PCM to other management entities indicating the state of the connection. |
| INT wfFddiPortMacIndicated | 1.3.6.1.4.1.18.3.4.15.4.2.1.12 | INTEGER | read-only | The indications (T_Val(9), R_Val(9)) in PC-Signalling, of the intent to place a MAC in the output token path to a PORT. |
| wfFddiPortExtTable | 1.3.6.1.4.1.18.3.4.15.4.3 | not-accessible | A list of PORT extension entries. | |
| wfFddiPortExtEntry | 1.3.6.1.4.1.18.3.4.15.4.3.1 | not-accessible | A PORT entry containing information common to a given PORT. | |
| INT wfFddiPortDelete | 1.3.6.1.4.1.18.3.4.15.4.3.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiPortExtSlot | 1.3.6.1.4.1.18.3.4.15.4.3.1.2 | INTEGER | read-only | Slot number associated with a Port entity. |
| INT wfFddiPortExtNode | 1.3.6.1.4.1.18.3.4.15.4.3.1.3 | INTEGER | read-only | Node/connector number associated with a Port entity. |
| INT wfFddiPortExtCct | 1.3.6.1.4.1.18.3.4.15.4.3.1.4 | INTEGER | read-only | Circuit number associated with a Port entity. |
| INT wfFddiPortExtIndex | 1.3.6.1.4.1.18.3.4.15.4.3.1.5 | INTEGER | read-only | A unique value for each PORT associated with each slot/connector pair. |
| INT wfFddiPortConnectionPolicies | 1.3.6.1.4.1.18.3.4.15.4.3.1.6 | INTEGER | read-only | A value representing the PORT's connection policies desired in the node. The value of 'pc-mac-lct' (i.e. PCM MAC LinkConfidence Test) is a term used in the PC_MAC_LCT Flag. The value of 'pc-mac-loop' is a term used in the PC_MAC_LOOP flag. The value is a sum. This value initially takes the value zero, then for each PORT policy, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power ------ ----- pc-mac-lct 0 pc-mac-loop 1 |
| INT wfFddiPortCurrentPath | 1.3.6.1.4.1.18.3.4.15.4.3.1.7 | INTEGER | read-only | Indicates the Path(s) into which this PORT is currently inserted. |
| INT wfFddiPortMacPlacement | 1.3.6.1.4.1.18.3.4.15.4.3.1.8 | INTEGER | read-only | Indicates the MAC, if any, whose transmit path exits the station via this PORT. The value shall be zero if there is no MAC associated with the PORT. |
| INT wfFddiPortAvailablePaths | 1.3.6.1.4.1.18.3.4.15.4.3.1.9 | INTEGER | read-only | Indicates the Paths which are available to this Port. In the absence of faults, the A & B ports will always have both the Primary & Secondary paths available. The value is a sum. This value initially takes the value 0, then for each type of PATH that this port has available, 2 raised to a power is added to the sum. The powers are according to the following table: Path Power ---- ----- Primary 0 Secondary 1 Local 2 |
| INT wfFddiPortPmdClass | 1.3.6.1.4.1.18.3.4.15.4.3.1.10 | INTEGER | read-only | Indicates the Path(s) into which this PORT is currently inserted. |
| INT wfFddiPortConnectionCapabilities | 1.3.6.1.4.1.18.3.4.15.4.3.1.11 | INTEGER | read-only | A value that indicates the connection capabilities of the port. The 'pc-mac-lct' bit indicates that the station has the capability of setting the PC_MAC_LCT Flag. The 'pc-mac-loop' bit indicates that the station has the capability of setting the PC_MAC_LOOP Flag. The value is a sum. This value initially takes the value zero, then for each PORT policy, 2 raised to a power is added to the sum. The powers are according to the following table: Capability Power ---------- ----- pc-mac-lct 0 pc-mac-loop 1 |
| INT wfFddiPortEbErrorCts | 1.3.6.1.4.1.18.3.4.15.4.3.1.12 | INTEGER | read-only | The count of the number of elasticity buffer errors for a particular PHY. The elasticity buffer is used to account for clock tolerances between stations |
| CTR wfFddiPortLctFailCts | 1.3.6.1.4.1.18.3.4.15.4.3.1.13 | Counter | read-only | The count of the consecutive times the link confidence test (LCT) has failed during Connection Management. |
| INT wfFddiPortLerEstimate | 1.3.6.1.4.1.18.3.4.15.4.3.1.14 | INTEGER | read-only | A long term average of the link error rate. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the base 10 logarithm. |
| CTR wfFddiPortLemRejectCts | 1.3.6.1.4.1.18.3.4.15.4.3.1.15 | Counter | read-only | A link error monitoring count of the times that a link has been rejected. |
| CTR wfFddiPortLemCts | 1.3.6.1.4.1.18.3.4.15.4.3.1.16 | Counter | read-only | The aggregate link error moniitor error count, set to 0 only on station initialization. |
| INT wfFddiPortLerCutOff | 1.3.6.1.4.1.18.3.4.15.4.3.1.17 | INTEGER | read-write | The link err rate estimate at which a link connection will be broken. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the base 10 logarithm. |
| INT wfFddiPortLerAlarm | 1.3.6.1.4.1.18.3.4.15.4.3.1.18 | INTEGER | read-write | The link err rate estimate at which a link connection will generate an alarm. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the base 10 logarithm of the estimate. |
| INT wfFddiPortPcWithhold | 1.3.6.1.4.1.18.3.4.15.4.3.1.19 | INTEGER | read-only | A variable from PCM to other management entities containing the reason for withholding a connection. |
| INT wfFddiPortHardwarePresent | 1.3.6.1.4.1.18.3.4.15.4.3.1.20 | INTEGER | read-only | This variable indicates the presence of underlying hardware support for this port object. |
| wfFddiPortActionTable | 1.3.6.1.4.1.18.3.4.15.4.4 | not-accessible | A list of Port Action entries. | |
| wfFddiPortActionEntry | 1.3.6.1.4.1.18.3.4.15.4.4.1 | not-accessible | A PORT entry containing actions common to a given PORT. | |
| INT wfFddiPortActionDelete | 1.3.6.1.4.1.18.3.4.15.4.4.1.1 | INTEGER | read-write | Create/delete parameter, default = create. |
| INT wfFddiPortActionSlot | 1.3.6.1.4.1.18.3.4.15.4.4.1.2 | INTEGER | read-only | Slot number associated with a PORT action entity. |
| INT wfFddiPortActionNode | 1.3.6.1.4.1.18.3.4.15.4.4.1.3 | INTEGER | read-only | Node/connector number associated with a PORT action entity. |
| INT wfFddiPortActionCct | 1.3.6.1.4.1.18.3.4.15.4.4.1.4 | INTEGER | read-only | Circuit number associated with a PORT action entity. |
| INT wfFddiPortActionIndex | 1.3.6.1.4.1.18.3.4.15.4.4.1.5 | INTEGER | read-only | A unique value for each PORT associated with each slot/connector pair. |
| INT wfFddiPortAction | 1.3.6.1.4.1.18.3.4.15.4.4.1.6 | INTEGER | read-write | Causes a control signal to be generated with a control_action of 'Signal' and the 'variable' parameter set with the appropriate value (i.e. PC_Maint, PC_Enable, PC_Disable, PC_Start, or PC_Stop). These signals are used to initiate a state change within Connection Management |
| wfFddiXGroup | 1.3.6.1.4.1.18.3.4.15.5 | |||
| wfFddiXLineCfgTable | 1.3.6.1.4.1.18.3.4.15.5.1 | not-accessible | FDDI switch configuration line record | |
| wfFddiXLineCfgEntry | 1.3.6.1.4.1.18.3.4.15.5.1.1 | not-accessible | An FDDI entry containing configuration parameters about an FDDI interface. | |
| INT wfFddiXLineCfgDelete | 1.3.6.1.4.1.18.3.4.15.5.1.1.1 | INTEGER | read-write | FDDI interface table create/delete object. The default setting is create. |
| INT wfFddiXLineCfgEnable | 1.3.6.1.4.1.18.3.4.15.5.1.1.2 | INTEGER | read-write | FDDI interface enable/disable object. The default setting is enable. |
| INT wfFddiXLineCfgLossOfServiceTmo | 1.3.6.1.4.1.18.3.4.15.5.1.1.3 | INTEGER | read-write | This timer (in seconds) provides debounce functionality for an FDDI interface. When the FDDI ring becomes non-operational, the LLC interface will be disabled if the following conditions hold TRUE: 1. fddimibMACMAUnitdataEnable (contained in fddimibMACTable of rfc1512.mib) is enabled 2. This FDDI interface has been unavailable for wfFddiXLineCfgLossOfServiceTmo seconds. If the FDDI interface becomes enabled before wfFddiXLineCfgLossOfServiceTmo expires, then the timer is cancelled and nothing occurs. This debounce timer may be disabled by setting it to 0. In this case, when the FDDI interface becomes non-operational, the LLC interface will be notified right away. |
| INT wfFddiXLineCfgSmtEnable | 1.3.6.1.4.1.18.3.4.15.5.1.1.4 | INTEGER | read-write | Enable Station Management periodic timers and NIF protocol. |
| INT wfFddiXLineCfgSmtDatProtocol | 1.3.6.1.4.1.18.3.4.15.5.1.1.5 | INTEGER | read-write | SMT will implement an optional ANSI duplicate address test involving periodic transmission of NSA NIF frames addressed to itself if enabled by this attribute. |
| INT wfFddiXLineCfgLineNumber | 1.3.6.1.4.1.18.3.4.15.5.1.1.6 | INTEGER | read-write | Logical line number associated with this driver entity. |
| INT wfFddiXLineCfgForcePeerTree | 1.3.6.1.4.1.18.3.4.15.5.1.1.7 | INTEGER | read-write | This attribute allows all FDDI Peer/Tree connections to reach the 'Thru' state. This is done to give the user some flexibility and allow them to Daisy Chain their Phy connections, mixing Tree & Peer connections. This type of daisy chaining DOES NOT conform to the SMT standard and is NOT recommended as it may result in a less than optimum token path. Normally when we have a Peer/Tree connection mix, we will wrap the connection, favoring PHY B. |
| INT wfFddiXLineCfgSlot | 1.3.6.1.4.1.18.3.4.15.5.1.1.8 | INTEGER | read-only | Chassis slot number of FDDI interface. |
| INT wfFddiXLineCfgModule | 1.3.6.1.4.1.18.3.4.15.5.1.1.9 | INTEGER | read-only | Module number for Fiddlestix platform, filled in by driver. |
| INT wfFddiXLineCfgActualNode | 1.3.6.1.4.1.18.3.4.15.5.1.1.10 | INTEGER | read-only | Actual Node number for this FDDI interface, filled in by the driver. |
| INT wfFddiXLineCfgNode | 1.3.6.1.4.1.18.3.4.15.5.1.1.11 | INTEGER | read-only | Instance ID node - filled in by driver. This attribute is an encoded value and is equal to 'module'*100 + 'node'. Where 'module' is defined in object 4 and 'node' is defined in object 5 of this table. |
| INT wfFddiXLineCfgSmtIndex | 1.3.6.1.4.1.18.3.4.15.5.1.1.12 | INTEGER | read-write | Used for indexing into rfc1512 MIBS, this value is gotten from multiplying the 'slot*1000' and then adding the 'wfFddiXLineCfgNode' attribute described above. Its purpose is to uniquely identify each SMT which exists. |
| INT wfFddiXLineCfgIfIndex | 1.3.6.1.4.1.18.3.4.15.5.1.1.13 | INTEGER | read-only | An index value that uniquely identifies an interface to a FDDI-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| wfFddiXLineTable | 1.3.6.1.4.1.18.3.4.15.5.2 | not-accessible | FDDI switch statistic line record | |
| wfFddiXLineEntry | 1.3.6.1.4.1.18.3.4.15.5.2.1 | not-accessible | An FDDI entry containing information about an FDDI interface. | |
| INT wfFddiXLineSlot | 1.3.6.1.4.1.18.3.4.15.5.2.1.1 | INTEGER | read-only | Chassis slot number of FDDI interface. |
| INT wfFddiXLineModule | 1.3.6.1.4.1.18.3.4.15.5.2.1.2 | INTEGER | read-only | Module number for Fiddlestix platform, filled in by driver. |
| INT wfFddiXLineActualNode | 1.3.6.1.4.1.18.3.4.15.5.2.1.3 | INTEGER | read-only | Actual Node number for this FDDI interface, filled in by the driver. |
| INT wfFddiXLineNode | 1.3.6.1.4.1.18.3.4.15.5.2.1.4 | INTEGER | read-only | Instance ID node - filled in by driver. This attribute is an encoded value and is equal to 'module'*10 + 'node'. Where 'module' is defined in object 4 and 'node' is defined in object 5 of this table. |
| INT wfFddiXLineSmtIndex | 1.3.6.1.4.1.18.3.4.15.5.2.1.5 | INTEGER | read-write | Logical line number associated with this FDDI interface. |
| INT wfFddiXLineIfIndex | 1.3.6.1.4.1.18.3.4.15.5.2.1.6 | INTEGER | read-only | An index value that uniquely identifies an interface to a FDDI-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| CTR wfFddiXLineTxErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.7 | Counter | read-only | An aggregate of the total number of transmit errors on this FDDI interface. |
| CTR wfFddiXLineTxAborts | 1.3.6.1.4.1.18.3.4.15.5.2.1.8 | Counter | read-only | Number of transmitted frames terminated (i.e. aborted) abnormally by the MAC. |
| CTR wfFddiXLineTxOverruns | 1.3.6.1.4.1.18.3.4.15.5.2.1.9 | Counter | read-only | Number of tranmitter overruns experienced by this interface. May indicate a HW problem with regards to the DMAC feeding the MAC. |
| CTR wfFddiXLineTxUnderruns | 1.3.6.1.4.1.18.3.4.15.5.2.1.10 | Counter | read-only | Number of tranmitter underruns experienced by this interface. May indicate a SW problem with regards to replenishing the DMACs XMT descriptor. |
| CTR wfFddiXLineRxErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.11 | Counter | read-only | An aggregate of the total number of receive errors on this FDDI interface. |
| CTR wfFddiXLineRxCrcErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.12 | Counter | read-only | Number of LLC frames received with CRC errors. |
| CTR wfFddiXLineRxSmtCrcErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.13 | Counter | read-only | Number of SMT frames received with CRC errors. |
| CTR wfFddiXLineRxInvalidFrameStatusErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.14 | Counter | read-only | A count of the number of badly formed LLC frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 control indicator symbols (i.e. E, A, C, flags). |
| CTR wfFddiXLineRxSmtInvalidFrameStatusErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.15 | Counter | read-only | A count of the number of badly formed SMT frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 control indicator symbols (i.e. E, A, C, flags). |
| CTR wfFddiXLineRxMacErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.16 | Counter | read-only | Number of LLC frames received with MAC errors. |
| CTR wfFddiXLineRxSmtMacErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.17 | Counter | read-only | Number of SMT frames received with MAC errors. |
| CTR wfFddiXLineRxFormatErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.18 | Counter | read-only | Number of LLC frames received with Format errors. |
| CTR wfFddiXLineRxSmtFormatErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.19 | Counter | read-only | Number of SMT frames received with Format errors. |
| CTR wfFddiXLineRxFragmentErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.20 | Counter | read-only | Number of LLC frame fragments received. |
| CTR wfFddiXLineRxSmtFragmentErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.21 | Counter | read-only | Number of SMT frame fragments received. |
| CTR wfFddiXLineRxInvalidLengthErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.22 | Counter | read-only | Number of LLC frames received with an ending T symbol which are either too short or contain an odd number of symbols. |
| CTR wfFddiXLineRxSmtInvalidLengthErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.23 | Counter | read-only | Number of SMT frames received with an ending T symbol which are either too short or contain an odd number of symbols. |
| CTR wfFddiXLineRxAbortErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.24 | Counter | read-only | Number of LLC frames aborted during reception. |
| CTR wfFddiXLineRxSmtAbortErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.25 | Counter | read-only | Number of LLC frames aborted during reception. |
| CTR wfFddiXLineRxEDataUnknownErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.26 | Counter | read-only | Number of LLC frames received with the Error indication set, that we couldn't decode as were unable to get the END_DATA value from the frame. |
| CTR wfFddiXLineRxSmtEDataUnknownErrors | 1.3.6.1.4.1.18.3.4.15.5.2.1.27 | Counter | read-only | Number of SMT frames received with the Error indication set, that we couldn't decode as were unable to get the END_DATA value from the frame. |
| INT wfFddiXLineRxLastEDataFStatusErrorVal | 1.3.6.1.4.1.18.3.4.15.5.2.1.28 | INTEGER | read-only | The value of END_DATA and FRAME_STATUS from the last LLC frame received containing an error. |
| INT wfFddiXLineRxSmtLastEDataFStatusErrorVal | 1.3.6.1.4.1.18.3.4.15.5.2.1.29 | INTEGER | read-only | The value of END_DATA and FRAME_STATUS from the last SMT frame received containing an error. |
| CTR wfFddiXLineRxOverruns | 1.3.6.1.4.1.18.3.4.15.5.2.1.30 | Counter | read-only | Number of receiver overruns experienced by this interface. May indicate a SW problem with regards to replenishing the DMACs RCV descriptors. |
| CTR wfFddiXLineRxUnderruns | 1.3.6.1.4.1.18.3.4.15.5.2.1.31 | Counter | read-only | Number of receiver underruns experienced by this interface. May indicate a HW problem with regards to the DMAC feeding the MAC. |
| CTR wfFddiXLineRxOversizedFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.32 | Counter | read-only | Number of LLC frames received whose length exceeded the MTU. (Note: The MTU is defined in rfc1573 in the ifMtu object.) |
| CTR wfFddiXLineRxSmtOversizedFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.33 | Counter | read-only | Number of SMT frames received whose length exceeded the MTU. (Note: The MTU is defined in rfc1573 in the ifMtu object.) |
| CTR wfFddiXLineRxUndersizedFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.34 | Counter | read-only | Number of LLC frames received whose length was less than 20 bytes, including the FC byte and a 4 byte CRC. |
| CTR wfFddiXLineRxSmtUndersizedFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.35 | Counter | read-only | Number of SMT frames received whose length was less than 37 bytes, including the FC byte and a 4 byte CRC. |
| CTR wfFddiXLineRxSmtSecondaryNsaFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.36 | Counter | read-only | Number of Secondary NSA frames received by this interface and dropped. |
| CTR wfFddiXLineUnexpectedFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.37 | Counter | read-only | Number of non-LLC and non SMT frames received by this interface. Does NOT include MAC frames or Void frames. |
| CTR wfFddiXLineRxSmtOctets | 1.3.6.1.4.1.18.3.4.15.5.2.1.38 | Counter | read-only | Number of bytes received without error. This byte count only includes SMT frames (i.e. no MAC and LLC frames). |
| CTR wfFddiXLineRxSmtFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.39 | Counter | read-only | Number of frames received without error. This frame count only includes SMT frames (i.e. no MAC and LLC frames). |
| CTR wfFddiXLineTxSmtOctets | 1.3.6.1.4.1.18.3.4.15.5.2.1.40 | Counter | read-only | Number of bytes transmitted. This byte count only includes SMT frames (i.e. no MAC and LLC frames). Also note that this value is an approximation in that its assumed frames queued for transmit ALWAYS make it onto the ring. |
| CTR wfFddiXLineTxSmtFrames | 1.3.6.1.4.1.18.3.4.15.5.2.1.41 | Counter | read-only | Number of frames transmitted. This frame count only includes SMT frames (i.e. no MAC and LLC frames). Also note that this value is an approximation in that its assumed frames queued for transmit ALWAYS make it onto the ring. |
| INT wfFddiXLinePhyALogPtr | 1.3.6.1.4.1.18.3.4.15.5.2.1.42 | INTEGER | read-only | Address of the Debug Phy Event Buffer for Phy A. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| INT wfFddiXLinePhyBLogPtr | 1.3.6.1.4.1.18.3.4.15.5.2.1.43 | INTEGER | read-only | Address of the Debug Phy Event Buffer for Phy B. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| wfFddiXSmtTable | 1.3.6.1.4.1.18.3.4.15.5.3 | not-accessible | A list of SMT entries. | |
| wfFddiXSmtEntry | 1.3.6.1.4.1.18.3.4.15.5.3.1 | not-accessible | An FDDI entry containing information about an FDDI interface. | |
| INT wfFddiXSmtIndex | 1.3.6.1.4.1.18.3.4.15.5.3.1.1 | INTEGER | read-only | A unique value for each SMT. The value for each SMT must remain constant at least from one re- initialization of the entity's network management system to the next re-initialization. |
| OCT wfFddiXSmtManufacturerData | 1.3.6.1.4.1.18.3.4.15.5.3.1.2 | OCTET STRING | read-only | Contains 32 Octets of manufacturer data. The first component, manufacturing OUI, is the 3 octet Organizationally Unique Identifier (OUI) assigned by IEEE. The second component, ManufacturerData, is the manufacturers data (29 octets). |
| wfFddiXMacTable | 1.3.6.1.4.1.18.3.4.15.5.4 | not-accessible | A list of MAC entries. | |
| wfFddiXMacEntry | 1.3.6.1.4.1.18.3.4.15.5.4.1 | not-accessible | An FDDI entry containing information about an FDDI interface. | |
| INT wfFddiXMacSmtIndex | 1.3.6.1.4.1.18.3.4.15.5.4.1.1 | INTEGER | read-only | The value of the SMT index associated with this MAC. |
| INT wfFddiXMacIndex | 1.3.6.1.4.1.18.3.4.15.5.4.1.2 | INTEGER | read-only | Index variable for uniquely identifying the MAC object instances, which is the same as the corresponding resource index in SMT. |
| INT wfFddiXMacBridgeFunctions | 1.3.6.1.4.1.18.3.4.15.5.4.1.3 | INTEGER | read-only | Indicates the MAC's optional bridging functions. The value is a sum. This value initially takes the value zero, then for each function present, 2 raised to a power is added to the sum. The powers are according to the following table: Function Power -------- ---- tb 0 -- Transparent bridging active sr 1 -- Src routing active srt 2 -- Src routing transparent active |
| CTR wfFddiXMacDuplicateTokenCts | 1.3.6.1.4.1.18.3.4.15.5.4.1.4 | Counter | read-only | The count of the number of times a Duplicate Token has been detected. |
| wfFddiXPortTable | 1.3.6.1.4.1.18.3.4.15.5.5 | not-accessible | A list of PORT Entries. | |
| wfFddiXPortEntry | 1.3.6.1.4.1.18.3.4.15.5.5.1 | not-accessible | An FDDI entry containing information about an FDDI interface. | |
| INT wfFddiXPortSmtIndex | 1.3.6.1.4.1.18.3.4.15.5.5.1.1 | INTEGER | read-only | The value of the SMT index associated with this PORT. |
| INT wfFddiXPortIndex | 1.3.6.1.4.1.18.3.4.15.5.5.1.2 | INTEGER | read-only | A unique value for each PORT within a given SMT, which is the same as the corresponding resource index in SMT. The value for each PORT must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| INT wfFddiXPortEbErrors | 1.3.6.1.4.1.18.3.4.15.5.5.1.3 | INTEGER | read-only | The count of the number of elasticity buffer errors for a particular PHY. The elasticity buffer is used to account for clock tolerances between stations. |
RFC description
Vendor-private MIB for Wellfleet FDDI (Fiber Distributed Data Interface) equipment management and monitoring.
Start monitoring Wellfleet/Bay Networks routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.