TRIPPLITE-12X

All MIBs › TRIPPLITE-12X

Organization: Tripp Lite

Last Updated: 2015-07-29

Category: Tripp Lite Power Management, UPS and Power Management

Description: Manages Tripp Lite 12-outlet UPS and power distribution units, monitoring load and battery status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TRIPPLITE-12X?

TRIPPLITE-12X is Tripp Lite's vendor MIB for their PowerAlert-managed UPS and power distribution products, exemplified by a 12-outlet model, providing remote management and notification configuration objects. Based on its sample objects it exposes contact/notification configuration: email contact lists (tlPAEmailContactsTable) and SNMP trap-receiver contact lists (tlPASnmpContactsTable), alongside vendor enumeration objects for supported host operating systems (tlOperatingSystems). While the broader Tripp Lite PowerAlert MIB family monitors UPS hardware status such as battery charge, load percentage, and runtime remaining, this excerpt centers on the alerting/contact configuration side, letting administrators ensure the right people/systems receive UPS fault and power-event notifications. It depends on standard RowStatus table-management conventions for adding/removing contacts. It is typically deployed wherever Tripp Lite UPS/PDU units protect server rooms or wiring closets and IT staff need email or SNMP-trap alerting configured for power events. Engineers can download the TRIPPLITE-12X file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TRIPPLITE-12X. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Tripp Lite UPS
Tripp Lite power distribution unit (PDU)

Monitoring Examples

An administrator would populate tlPAEmailContactsTable with entries (tlPAEmailContactName, tlPAEmailContactAddress) so on-call staff get emailed on a UPS power event, and similarly populate tlPASnmpContactsTable so an NMS receives SNMP trap notifications. Checking tlPAEmailContactRowStatus confirms whether a contact entry is active versus provisioned-but-disabled. tlPANumberOfSnmpContacts and tlPANumberOfEmailContacts give a quick count to verify all expected recipients are configured before a maintenance window.

What Can Be Monitored

configured email alert contacts
configured SNMP trap contacts
contact entry status
number of configured email/SNMP contacts

Imported Objects

From RFC-1215

TRAP-TYPE

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

AutonomousType
DateAndTime
DisplayString
RowStatus
TimeInterval
TimeStamp
TruthValue
VariablePointer

From TRIPPLITE

tripplite

MODULE-IDENTITY

From UPS-MIB

NonNegativeInteger
PositiveInteger

How to Use in IPNetwork Monitor

Example using tlUpsAlarmsPresent OID:

Select a Tripp Lite UPS, power distribution unit (PDU), PowerAlert-managed (email/SNMP contact config status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tlUpsAlarmsPresent into the Find box to locate it in the OID tree, then select it and click OK. The present number of active alarm conditions. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
aix	1.3.6.1.4.1.850.2.1.54
bsdi	1.3.6.1.4.1.850.2.1.11
freebsd	1.3.6.1.4.1.850.2.1.8
hpux10	1.3.6.1.4.1.850.2.1.6
hpux11	1.3.6.1.4.1.850.2.1.14
hpux9	1.3.6.1.4.1.850.2.1.1
irix	1.3.6.1.4.1.850.2.1.9
linux	1.3.6.1.4.1.850.2.1.10
netbsd1	1.3.6.1.4.1.850.2.1.7
openbsd	1.3.6.1.4.1.850.2.1.12
osf	1.3.6.1.4.1.850.2.1.4
osx	1.3.6.1.4.1.850.2.1.56
sco	1.3.6.1.4.1.850.2.1.55
solaris	1.3.6.1.4.1.850.2.1.3
solintel	1.3.6.1.4.1.850.2.1.53
solspark	1.3.6.1.4.1.850.2.1.52
sunos4	1.3.6.1.4.1.850.2.1.2
tlBasicGroups	1.3.6.1.4.1.850.20.2.2
tlCompliances	1.3.6.1.4.1.850.20.1
tlConformance	1.3.6.1.4.1.850.20
tlCooling	1.3.6.1.4.1.850.103
tlCoolingAirFilterClogged	1.3.6.1.4.1.850.103.6.3.7			The air filter is clogged.
I32 tlCoolingAirFilterInterval	1.3.6.1.4.1.850.103.1.4.14	Integer32	read-write	The number of weeks before the air filter needs to be changed.
I32 tlCoolingAirFilterRunHours	1.3.6.1.4.1.850.103.1.3.1	Integer32	read-only	Total hours the air filter has been under operation.
tlCoolingAirFilterRunHoursViolation	1.3.6.1.4.1.850.103.6.3.8			The air filter run hours was violated.
tlCoolingAlarm	1.3.6.1.4.1.850.103.6
I32 tlCoolingAtomizerRunDays	1.3.6.1.4.1.850.103.1.3.6	Integer32	read-only	Total days the atomizer has been under operation.
tlCoolingAutoCoolingOn	1.3.6.1.4.1.850.103.6.3.35			Automatic cooling was activated to lower the temperature below the remote set point.
INT tlCoolingAutoStart	1.3.6.1.4.1.850.103.1.4.3	INTEGER	read-write	Specified if the unit should start automatically on power up.
INT tlCoolingBeepOnKey	1.3.6.1.4.1.850.103.1.4.8	INTEGER	read-write	Indicates if the display sounds a beep when a key is pressed.
INT tlCoolingCompCurrent	1.3.6.1.4.1.850.103.1.2.13	INTEGER	read-only	The operating current of the compressor in Arms.
INT tlCoolingCompFrequency	1.3.6.1.4.1.850.103.1.2.9	INTEGER	read-only	The operating frequency of the compressor in tenths of Arms.
tlCoolingCompressorFailure	1.3.6.1.4.1.850.103.6.3.28			The compressor has failed.
I32 tlCoolingCompressorRunDays	1.3.6.1.4.1.850.103.1.3.4	Integer32	read-only	Total days the compressor has been under operation.
tlCoolingCondensatePumpFault	1.3.6.1.4.1.850.103.6.3.12			The condensate pump is in fault.
tlCoolingCondenserFailure	1.3.6.1.4.1.850.103.6.3.15			The condenser has failed.
tlCoolingCondenserFanFault	1.3.6.1.4.1.850.103.6.3.14			The condenser fan is in fault.
tlCoolingCondenserInletAirSensorFault	1.3.6.1.4.1.850.103.6.3.3			The condenser inlet air sensor is in fault.
tlCoolingCondenserOutletAirSensorFault	1.3.6.1.4.1.850.103.6.3.4			The condenser outlet air sensor is in fault.
I32 tlCoolingCondFanRunDays	1.3.6.1.4.1.850.103.1.3.3	Integer32	read-only	Total days the condenser fan has been under operation.
INT tlCoolingCondFanSpeed	1.3.6.1.4.1.850.103.1.2.8	INTEGER	read-only	The current speed of the condenser fan.
INT tlCoolingCondInletTemp	1.3.6.1.4.1.850.103.1.2.2	INTEGER	read-only	The condenser inlet air stream temperature in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
INT tlCoolingCondOutletTemp	1.3.6.1.4.1.850.103.1.2.1	INTEGER	read-only	The condenser outlet air stream temperature in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
I32 tlCoolingCondPumpRunDays	1.3.6.1.4.1.850.103.1.3.5	Integer32	read-only	Total days the condensate pump has been under operation.
tlCoolingConfig	1.3.6.1.4.1.850.103.1.4
INT tlCoolingControlType	1.3.6.1.4.1.850.103.1.4.5	INTEGER	read-write	Which temperature to be used as a control point.
tlCoolingCurrentLimit	1.3.6.1.4.1.850.103.6.3.29			The current is out of range.
INT tlCoolingCurrentRemoteTemp	1.3.6.1.4.1.850.103.1.4.6	INTEGER	read-write	The external remote temperature in tenths of degrees in Celcius or Fahrenheit depending upon value of tlCoolingDisplayUnits
INT tlCoolingDischargePressure	1.3.6.1.4.1.850.103.1.2.6	INTEGER	read-only	The pressure of the compressor discharge line in tenths of (Mpa/psi) depending on the value of tlCoolingDisplayUnits.
tlCoolingDischargePressureHigh	1.3.6.1.4.1.850.103.6.3.21			The discharge pressure is high.
tlCoolingDischargePressurePersistentHigh	1.3.6.1.4.1.850.103.6.3.23			The discharge pressure is persistently high.
tlCoolingDischargePressureSensorFault	1.3.6.1.4.1.850.103.6.3.33			The discharge pressure sensor is in fault.
tlCoolingDisconnectedFromDevice	1.3.6.1.4.1.850.103.6.3.37			The device communications is disconnected.
INT tlCoolingDisplayUnits	1.3.6.1.4.1.850.103.1.4.7	INTEGER	read-write	Selects English or Metric display for all readings.
INT tlCoolingEEVPercentage	1.3.6.1.4.1.850.103.1.2.10	INTEGER	read-only	The opening percentage of the EEV.
INT tlCoolingEnableAirFilterAlarm	1.3.6.1.4.1.850.103.1.5.2	INTEGER	read-write	When enabled indicated that an alarm should occur when the maximum number of air filter run hours has been exceeded.
tlCoolingEnvironment	1.3.6.1.4.1.850.103.1
I32 tlCoolingEvapFanRunDays	1.3.6.1.4.1.850.103.1.3.2	Integer32	read-only	Total days the evaporator fan has been under operation.
INT tlCoolingEvapFanSpeed	1.3.6.1.4.1.850.103.1.2.7	INTEGER	read-only	The current speed of the evaporator fan.
tlCoolingEvaporatorCoolingFailure	1.3.6.1.4.1.850.103.6.3.16			The evaporator cooling is in fault.
tlCoolingEvaporatorFailure	1.3.6.1.4.1.850.103.6.3.19			The evaporator has failed.
tlCoolingEvaporatorFreezeUp	1.3.6.1.4.1.850.103.6.3.20			The evaporator is frozen.
tlCoolingEvaporatorTemperatureSensorFault	1.3.6.1.4.1.850.103.6.3.6			The evaporator temperature sensor is in fault.
INT tlCoolingEvapSurfaceTemp	1.3.6.1.4.1.850.103.1.2.4	INTEGER	read-only	The surface temperature of the evaporator in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
INT tlCoolingFanCurrent	1.3.6.1.4.1.850.103.1.2.12	INTEGER	read-only	Thethe current draw of the Evaporator and Condenser fans in tents of Arms.
tlCoolingFanOverCurrent	1.3.6.1.4.1.850.103.6.3.32			The fan is over current.
INT tlCoolingFanSpeedOverride	1.3.6.1.4.1.850.103.1.4.4	INTEGER	read-write	Speed of evaporator fan set by the user.
tlCoolingFanUnderCurrent	1.3.6.1.4.1.850.103.6.3.31			The fan is under current.
STR tlCoolingFirmwareVersion	1.3.6.1.4.1.850.103.1.1.4	DisplayString	read-only	The firmware version of the AC Unit.
STR tlCoolingHostSoftwareVersion	1.3.6.1.4.1.850.103.1.1.5	DisplayString	read-only	The hardware version of the AC unit.
tlCoolingIdent	1.3.6.1.4.1.850.103.1.1
INT tlCoolingInputContactType	1.3.6.1.4.1.850.103.1.4.12	INTEGER	read-write	The input contact type.
tlCoolingInverterCommunicationsFault	1.3.6.1.4.1.850.103.6.3.10			The inverter communications is in fault.
STR tlCoolingLocation	1.3.6.1.4.1.850.103.1.1.7	DisplayString	read-write	The user defined location of the AC Unit.
tlCoolingLowRefrigerantStartupFault	1.3.6.1.4.1.850.103.6.3.13			The low refrigerant startup is in fault.
STR tlCoolingManufacturer	1.3.6.1.4.1.850.103.1.1.2	DisplayString	read-only	The manufacturer of the AC Unit.
I32 tlCoolingMaxAirFilterRunHours	1.3.6.1.4.1.850.103.1.5.1	Integer32	read-write	The maximum interval for air filter run hours before warning is annunciated.
INT tlCoolingMaxReturnAirTemp	1.3.6.1.4.1.850.103.1.5.6	INTEGER	read-write	When enabled indicated that an alarm should occur when the maximum number of air filter run hours has been exceeded.
INT tlCoolingMaxSupplyTemp	1.3.6.1.4.1.850.103.1.5.3	INTEGER	read-write	Maximum allowed supply air temperature before firing an alarm.
INT tlCoolingMinSupplyTemp	1.3.6.1.4.1.850.103.1.5.4	INTEGER	read-write	Minimum allowed supply air temperature allowed before firing an alarm.
STR tlCoolingModel	1.3.6.1.4.1.850.103.1.1.1	DisplayString	read-only	The model name for the AC Unit.
STR tlCoolingName	1.3.6.1.4.1.850.103.1.1.6	DisplayString	read-write	The user defined name for the AC Unit.
INT tlCoolingOffOnInputContact	1.3.6.1.4.1.850.103.1.4.11	INTEGER	read-write	Indicates if the unit should stop cooling when input contact is activated.
INT tlCoolingOffOnLeak	1.3.6.1.4.1.850.103.1.4.10	INTEGER	read-write	Indicates if the unit should stop cooling when leak input is activated.
INT tlCoolingOnOff	1.3.6.1.4.1.850.103.1.4.1	INTEGER	read-write	Turn the unit off or on.
INT tlCoolingOutputRelayDefault	1.3.6.1.4.1.850.103.1.4.13	INTEGER	read-write	Type of contact to make when output relay is activated.
INT tlCoolingOutputRelaySource	1.3.6.1.4.1.850.103.1.4.9	INTEGER	read-write	The alarm level that causes the ouput relay to activate.
tlCoolingPowerButtonPressed	1.3.6.1.4.1.850.103.6.3.36			Power button was pressed on the front panel.
tlCoolingPressureGaugeFailure	1.3.6.1.4.1.850.103.6.3.22			The pressure gauge has failed.
INT tlCoolingRefrigerantTemp	1.3.6.1.4.1.850.103.1.2.3	INTEGER	read-only	The temperature of the refrigerant in the suction line. This is displayed in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
tlCoolingRemoteShutdownViaInputContact	1.3.6.1.4.1.850.103.6.3.11			A remote shutdown was triggerd by an input contact.
tlCoolingReturnAirSensorFault	1.3.6.1.4.1.850.103.6.3.2			The return air sensor is in fault.
INT tlCoolingReturnAirTemp	1.3.6.1.4.1.850.103.1.2.14	INTEGER	read-only	The return air temperature in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
tlCoolingReturnAirTempHigh	1.3.6.1.4.1.850.103.6.3.17			The return air temperature is high.
tlCoolingRunTimes	1.3.6.1.4.1.850.103.1.3
STR tlCoolingSerialNumber	1.3.6.1.4.1.850.103.1.1.3	DisplayString	read-only	The serial number of the AC unit.
INT tlCoolingSetPointTemp	1.3.6.1.4.1.850.103.1.4.2	INTEGER	read-write	The set point temperature the unit will control the temperature to in tenths of degrees in Celcius or Fahrenheit based upon tleCoolDisplayUnits.
tlCoolingStartupLinePressureImbalance	1.3.6.1.4.1.850.103.6.3.27			The startup line pressure is in imbalance.
tlCoolingStatus	1.3.6.1.4.1.850.103.1.2
INT tlCoolingSuctionPressure	1.3.6.1.4.1.850.103.1.2.5	INTEGER	read-only	The pressure of the compressor suction line in tenths of (Mpa/psi) depending on the value of tlCoolingDisplayUnits.
tlCoolingSuctionPressureLow	1.3.6.1.4.1.850.103.6.3.25			The suction pressure is low.
tlCoolingSuctionPressureLowStartFailure	1.3.6.1.4.1.850.103.6.3.24			Cannot start due to low suction pressure.
tlCoolingSuctionPressurePersistentLow	1.3.6.1.4.1.850.103.6.3.26			The suction pressure is persistently low.
tlCoolingSuctionPressureSensorFault	1.3.6.1.4.1.850.103.6.3.9			The suction pressure sensor is in fault.
INT tlCoolingSuctionTemp	1.3.6.1.4.1.850.103.1.2.15	INTEGER	read-only	The temperature of the compressor suction line in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
tlCoolingSuctionTemperatureSensorFault	1.3.6.1.4.1.850.103.6.3.5			The suction temperature sensor is in fault.
tlCoolingSupplyAirSensorFault	1.3.6.1.4.1.850.103.6.3.1			The supply air sensor is in fault.
INT tlCoolingSupplyAirTemp	1.3.6.1.4.1.850.103.1.2.16	INTEGER	read-only	The supply air temperature in tenths of degrees in the units Celcius/Fahrenheit as specified in tlCoolingDisplayUnits.
tlCoolingSupplyAirTempHigh	1.3.6.1.4.1.850.103.6.3.18			The supply air temperature is high.
INT tlCoolingTempDiffAlarm	1.3.6.1.4.1.850.103.1.5.5	INTEGER	read-write	Maximum allowed air temperature deviation from set allowed before firing an alarm.
tlCoolingThresholds	1.3.6.1.4.1.850.103.1.5
INT tlCoolingUnitCurrent	1.3.6.1.4.1.850.103.1.2.11	INTEGER	read-only	The the total current draw of the unit in tenths of Arms.
tlCoolingWaterFull	1.3.6.1.4.1.850.103.6.3.34			Water is Full.
tlCoolingWaterLeak	1.3.6.1.4.1.850.103.6.3.30			Water is leaking.
INT tlCoolingWaterLeakContactType	1.3.6.1.4.1.850.103.1.4.15	INTEGER	read-write	The input contact type.
tlCoolingWellKnownAlarms	1.3.6.1.4.1.850.103.6.3
tlEnumerations	1.3.6.1.4.1.850.2
INT tlEnvContactConfig	1.3.6.1.4.1.850.101.2.1.1.4	INTEGER	read-write	The configuration of the contact.
tlEnvContactEntry	1.3.6.1.4.1.850.101.2.1.1		not-accessible	An entry containing information applicable to a particular contact.
NUM tlEnvContactIndex	1.3.6.1.4.1.850.101.2.1.1.1	PositiveInteger	read-only	The table row index for the contact.
STR tlEnvContactName	1.3.6.1.4.1.850.101.2.1.1.2	DisplayString	read-write	The name or description of the contact.
tlEnvContacts	1.3.6.1.4.1.850.101.2
INT tlEnvContactStatus	1.3.6.1.4.1.850.101.2.1.1.3	INTEGER	read-only	The current status of the contact.
tlEnvContactTable	1.3.6.1.4.1.850.101.2.1		not-accessible	A table of contacts.
tlEnvEnvironment	1.3.6.1.4.1.850.101.1
I32 tlEnvHumidity	1.3.6.1.4.1.850.101.1.2.1	Integer32	read-only	The ambient humidity (%).
tlEnvHumidityData	1.3.6.1.4.1.850.101.1.2
I32 tlEnvHumidityHighLimit	1.3.6.1.4.1.850.101.1.2.3	Integer32	read-write	The upper alarm limit for ambient humidity (%).
T/F tlEnvHumidityInAlarm	1.3.6.1.4.1.850.101.1.2.4	TruthValue	read-only	Indicates whether or not humidity is in alarm.
I32 tlEnvHumidityLowLimit	1.3.6.1.4.1.850.101.1.2.2	Integer32	read-write	The lower alarm limit for ambient humidity (%).
tlEnviroSense	1.3.6.1.4.1.850.101
I32 tlEnvTemperatureC	1.3.6.1.4.1.850.101.1.1.1	Integer32	read-only	The ambient temperature (C).
tlEnvTemperatureData	1.3.6.1.4.1.850.101.1.1
I32 tlEnvTemperatureF	1.3.6.1.4.1.850.101.1.1.2	Integer32	read-only	The ambient temperature (F).
I32 tlEnvTemperatureHighLimit	1.3.6.1.4.1.850.101.1.1.4	Integer32	read-write	The upper alarm limit for ambient temperature (F).
T/F tlEnvTemperatureInAlarm	1.3.6.1.4.1.850.101.1.1.5	TruthValue	read-only	Indicates whether or not temperature is in alarm.
I32 tlEnvTemperatureLowLimit	1.3.6.1.4.1.850.101.1.1.3	Integer32	read-write	The lower alarm limit for ambient temperature (F).
tlFullGroups	1.3.6.1.4.1.850.20.2.3
tlGroups	1.3.6.1.4.1.850.20.2
tlOperatingSystems	1.3.6.1.4.1.850.2.1
tlPAContacts	1.3.6.1.4.1.850.90.1.1
STR tlPAEmailContactAddress	1.3.6.1.4.1.850.90.1.1.1.2.1.4	DisplayString	read-write	The address of the email contact.
tlPAEmailContactEntry	1.3.6.1.4.1.850.90.1.1.1.2.1		not-accessible	An entry containing email contacts information.
NUM tlPAEmailContactIndex	1.3.6.1.4.1.850.90.1.1.1.2.1.1	PositiveInteger	read-only	This is the index number of the email contact.
STR tlPAEmailContactName	1.3.6.1.4.1.850.90.1.1.1.2.1.3	DisplayString	read-write	The name of the email contact.
ROW tlPAEmailContactRowStatus	1.3.6.1.4.1.850.90.1.1.1.2.1.2	RowStatus	read-write	The row status for the tlPAEmailContactTable row
tlPAEmailContacts	1.3.6.1.4.1.850.90.1.1.1
tlPAEmailContactsTable	1.3.6.1.4.1.850.90.1.1.1.2		not-accessible	A list email contact entries. The number of entries is given by the value of tlPANumberOfEmailContacts.
NUM tlPANumberOfEmailContacts	1.3.6.1.4.1.850.90.1.1.1.1	NonNegativeInteger	read-only	The number email contacts currently defined.
NUM tlPANumberOfSnmpContacts	1.3.6.1.4.1.850.90.1.1.2.1	NonNegativeInteger	read-only	The number SNMP contacts currently defined.
STR tlPASnmpContactAuthPassword	1.3.6.1.4.1.850.90.1.1.2.2.1.9	DisplayString	read-write	The SNMP contact auth password to use for sending V3 traps.
tlPASnmpContactEntry	1.3.6.1.4.1.850.90.1.1.2.2.1		not-accessible	An entry containing SNMP contacts information.
NUM tlPASnmpContactIndex	1.3.6.1.4.1.850.90.1.1.2.2.1.1	PositiveInteger	read-only	This is the index number of this SNMP contact.
STR tlPASnmpContactIpAddress	1.3.6.1.4.1.850.90.1.1.2.2.1.4	DisplayString	read-write	The IP address of the SNMP contact.
STR tlPASnmpContactName	1.3.6.1.4.1.850.90.1.1.2.2.1.3	DisplayString	read-write	The name of the SNMP contact.
NUM tlPASnmpContactPort	1.3.6.1.4.1.850.90.1.1.2.2.1.5	PositiveInteger	read-write	The port of the SNMP contact.
STR tlPASnmpContactPrivPassword	1.3.6.1.4.1.850.90.1.1.2.2.1.8	DisplayString	read-write	The SNMP contact priv password to use for sending V3 traps.
ROW tlPASnmpContactRowStatus	1.3.6.1.4.1.850.90.1.1.2.2.1.2	RowStatus	read-write	The row status for the tlPASnmpContactTable row
tlPASnmpContacts	1.3.6.1.4.1.850.90.1.1.2
STR tlPASnmpContactSecurityName	1.3.6.1.4.1.850.90.1.1.2.2.1.7	DisplayString	read-write	The SNMP contact security name.
INT tlPASnmpContactSnmpVersion	1.3.6.1.4.1.850.90.1.1.2.2.1.6	INTEGER	read-write	The SNMP contact version to use for sending traps.
tlPASnmpContactsTable	1.3.6.1.4.1.850.90.1.1.2.2		not-accessible	A list SNMP contact entries. The number of entries is given by the value of tlPANumberOfSnmpContacts.
tlPASystem	1.3.6.1.4.1.850.90.1
tlPowerAlert	1.3.6.1.4.1.850.90			This MIB module defines MIB objects which provide mechanisms for remote management capabilities of Tripplite PowerAlert and related software.
tlSrCoolNet	1.3.6.1.4.1.850.104
tlSrCoolNetAlarm	1.3.6.1.4.1.850.104.2
tlSrCoolNetConfig	1.3.6.1.4.1.850.104.1.3
INT tlSrCoolNetCurrentRemoteTemp	1.3.6.1.4.1.850.104.1.2.5	INTEGER	read-only	The EnviroSense temperature in tenths of degrees in Celsius or Fahrenheit depending upon value of tlSrCoolNetDisplayUnits. Only available if EnviroSense is connected to SRCOOLNET.
tlSrCoolNetData	1.3.6.1.4.1.850.104.1
INT tlSrCoolNetDisplayUnits	1.3.6.1.4.1.850.104.1.2.6	INTEGER	read-only	Selects English or Metric display for all readings. AC unit must be manually configured to match this setting.
INT tlSrCoolNetFanAlwaysOn	1.3.6.1.4.1.850.104.1.3.7	INTEGER	read-write	Leave fans on when not cooling. Only available when EnviroSense is connected to SRCOOLNET.
INT tlSrCoolNetFanSpeed	1.3.6.1.4.1.850.104.1.2.2	INTEGER	read-only	The current speed of the fan.
INT tlSrCoolNetFanSpeedSetting	1.3.6.1.4.1.850.104.1.3.5	INTEGER	read-write	Set the fan speed of the AC unit.
STR tlSrCoolNetHostSoftwareVersion	1.3.6.1.4.1.850.104.1.1.4	DisplayString	read-only	The software version of the SRCOOLNET device.
tlSrCoolNetIdent	1.3.6.1.4.1.850.104.1.1
STR tlSrCoolNetLocation	1.3.6.1.4.1.850.104.1.1.6	DisplayString	read-write	The user defined location of the AC Unit.
STR tlSrCoolNetManufacturer	1.3.6.1.4.1.850.104.1.1.2	DisplayString	read-only	The manufacturer of the AC Unit.
INT tlSrCoolNetMode	1.3.6.1.4.1.850.104.1.2.1	INTEGER	read-only	The current mode of SRCOOLNET.
STR tlSrCoolNetModel	1.3.6.1.4.1.850.104.1.1.1	DisplayString	read-only	The model name for the device attached to the SRCOOLNET.
STR tlSrCoolNetName	1.3.6.1.4.1.850.104.1.1.5	DisplayString	read-write	The user defined name for the AC Unit.
INT tlSrCoolNetOnOff	1.3.6.1.4.1.850.104.1.3.1	INTEGER	read-write	Turn the unit off or on.
INT tlSrCoolNetRemoteSetpointEnable	1.3.6.1.4.1.850.104.1.3.6	INTEGER	read-write	Use remote temperature setpoint for control point versus return air temp. Only available when EnviroSense is connected to SRCOOLNET.
INT tlSrCoolNetRemoteSetPointTemp	1.3.6.1.4.1.850.104.1.3.4	INTEGER	read-write	The remote set point temperature in tenths of degrees in Celsius or Fahrenheit based upon tlSrCoolNetDisplayUnits. Only available when EnviroSense is connected to SRCOOLNET.
INT tlSrCoolNetReturnAirTemp	1.3.6.1.4.1.850.104.1.2.3	INTEGER	read-only	The return air stream temperature in tenths of degrees in the units Celsius/Fahrenheit as specified in tlSrCoolNetDisplayUnits.
STR tlSrCoolNetSerialNumber	1.3.6.1.4.1.850.104.1.1.3	DisplayString	read-only	The serial number of the SRCOOLNET device.
INT tlSrCoolNetSetPointTemp	1.3.6.1.4.1.850.104.1.3.3	INTEGER	read-write	The local set point temperature in tenths of degrees in Celsius or Fahrenheit based upon tlSrCoolNetDisplayUnits.
tlSrCoolNetStatus	1.3.6.1.4.1.850.104.1.2
INT tlSrCoolNetWaterFull	1.3.6.1.4.1.850.104.1.2.4	INTEGER	read-only	Indicates the water reservoir is full or not full.
tlSrCoolNetWaterFullAlarm	1.3.6.1.4.1.850.104.2.1.1			Water reservoir full.
tlSrCoolNetWellKnownAlarms	1.3.6.1.4.1.850.104.2.1
INT tlSrCoolSetMode	1.3.6.1.4.1.850.104.1.3.2	INTEGER	read-write	Set the operating mode of cooling unit. Unit must be ON to set mode.
tlSubsetGroups	1.3.6.1.4.1.850.20.2.1
tlUPS	1.3.6.1.4.1.850.100
NUM tlUpsAggregatePowerFactor	1.3.6.1.4.1.850.100.1.4.8	PositiveInteger	read-only	The aggregrate power factor of all phases.
tlUpsAlarm	1.3.6.1.4.1.850.100.1.6
tlUpsAlarmAwaitingPower	1.3.6.1.4.1.850.100.1.6.3.28			The UPS output is off and the UPS is awaiting the return of input power.
tlUpsAlarmBatteryAgeAboveThreshold	1.3.6.1.4.1.850.100.1.6.3.5			One or more batteries have been determined to require replacement.
tlUpsAlarmBatteryBad	1.3.6.1.4.1.850.100.1.6.3.8			One or more batteries have been determined to require replacement.
tlUpsAlarmBatteryOverVoltage	1.3.6.1.4.1.850.100.1.6.3.52			The battery voltage is too high.
tlUpsAlarmBatteryUnderVoltage	1.3.6.1.4.1.850.100.1.6.3.53			The battery voltage is too low.
tlUpsAlarmBusOverVoltage	1.3.6.1.4.1.850.100.1.6.3.45			The inverter bus voltage is too high.
tlUpsAlarmBusStartVoltageLow	1.3.6.1.4.1.850.100.1.6.3.44			The inverter start up bus voltage is too low.
tlUpsAlarmBusUnderVoltage	1.3.6.1.4.1.850.100.1.6.3.46			The inverter bus voltage is too low.
tlUpsAlarmBusVoltageUnbalanced	1.3.6.1.4.1.850.100.1.6.3.47			The inverter bus voltage is not balanced.
tlUpsAlarmBypassBad	1.3.6.1.4.1.850.100.1.6.3.17			The Bypass is out of tolerance.
tlUpsAlarmBypassFrequencyBad	1.3.6.1.4.1.850.100.1.6.3.58			The bypass frequency is out of tolerance.
I32 tlUpsAlarmCategory	1.3.6.1.4.1.850.100.1.6.9	Integer32	read-only	The category, tlDevEvtCategory, of this alarm.
tlUpsAlarmChargerFailed	1.3.6.1.4.1.850.100.1.6.3.20			An uncorrected problem has been detected within the UPS charger subsystem.
tlUpsAlarmCircuitBreaker1Open	1.3.6.1.4.1.850.100.1.6.3.32			Circuit breakers #1 is open.
tlUpsAlarmCircuitBreaker2Open	1.3.6.1.4.1.850.100.1.6.3.33			Circuit breakers #2 is open.
tlUpsAlarmCircuitBreaker3Open	1.3.6.1.4.1.850.100.1.6.3.34			Circuit breakers #3 is open.
tlUpsAlarmCircuitBreaker4Open	1.3.6.1.4.1.850.100.1.6.3.35			Circuit breakers #4 is open.
tlUpsAlarmCircuitBreaker5Open	1.3.6.1.4.1.850.100.1.6.3.36			Circuit breakers #5 is open.
tlUpsAlarmCircuitBreaker6Open	1.3.6.1.4.1.850.100.1.6.3.37			Circuit breakers #6 is open.
tlUpsAlarmCircuitBreaker7Open	1.3.6.1.4.1.850.100.1.6.3.38			Circuit breakers #7 is open.
tlUpsAlarmCircuitBreaker8Open	1.3.6.1.4.1.850.100.1.6.3.39			Circuit breakers #8 is open.
tlUpsAlarmCommunicationsLost	1.3.6.1.4.1.850.100.1.6.3.27			A problem has been encountered in the communications between the agent and the UPS.
tlUpsAlarmCurrent1AboveThreshold	1.3.6.1.4.1.850.100.1.6.3.40			The output current on line 1 exceeds load limits.
tlUpsAlarmCurrent2AboveThreshold	1.3.6.1.4.1.850.100.1.6.3.41			The output current on line 2 exceeds load limits.
tlUpsAlarmCurrent3AboveThreshold	1.3.6.1.4.1.850.100.1.6.3.42			The output current on line 3 exceeds load limits.
tlUpsAlarmDepletedBattery	1.3.6.1.4.1.850.100.1.6.3.11			The UPS will be unable to sustain the present load when and if the utility power is lost.
OID tlUpsAlarmDescr	1.3.6.1.4.1.850.100.1.6.2.1.2	AutonomousType	read-only	A description of the alarm condition.
STR tlUpsAlarmDetail	1.3.6.1.4.1.850.100.1.6.2.1.4	DisplayString	read-only	A textual description of the alarm condition.
NUM tlUpsAlarmDeviceId	1.3.6.1.4.1.850.100.1.6.2.1.5	PositiveInteger	read-only	A numeric identifier for the device on which the alarm is active.
STR tlUpsAlarmDeviceName	1.3.6.1.4.1.850.100.1.6.2.1.6	DisplayString	read-only	A string identifier for the device on which the alarm is active.
STR tlUpsAlarmDevLocation	1.3.6.1.4.1.850.100.1.6.8	DisplayString	read-only	The location of the device, tlDevLocation, corresponding to the device that is associated with this alarm.
STR tlUpsAlarmDevName	1.3.6.1.4.1.850.100.1.6.7	DisplayString	read-only	The name of the device, tlDevName, corresponding to the device that is associated with this alarm.
tlUpsAlarmDiagnosticTestFailed	1.3.6.1.4.1.850.100.1.6.3.26			The result of the last diagnostic test indicates a failure.
tlUpsAlarmEntry	1.3.6.1.4.1.850.100.1.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.
tlUpsAlarmEPOActive	1.3.6.1.4.1.850.100.1.6.3.57			The EPO is currently activate.
tlUpsAlarmExternalNonSmartBatteryAgeAboveThreshold	1.3.6.1.4.1.850.100.1.6.3.60			One or more external non-smart batteries have been determined to require replacement.
tlUpsAlarmExternalSmartBatteryAgeAboveThreshold	1.3.6.1.4.1.850.100.1.6.3.59			One or more external smart batteries have been determined to require replacement.
tlUpsAlarmFanFailure	1.3.6.1.4.1.850.100.1.6.3.23			The failure of one or more fans in the UPS has been detected.
tlUpsAlarmFuseFailure	1.3.6.1.4.1.850.100.1.6.3.24			The failure of one or more fuses has been detected.
tlUpsAlarmGeneralFault	1.3.6.1.4.1.850.100.1.6.3.25			A general fault in the UPS has been detected.
INT tlUpsAlarmGroup	1.3.6.1.4.1.850.100.1.6.2.1.8	INTEGER	read-only	The category/group of this alarm.
NUM tlUpsAlarmId	1.3.6.1.4.1.850.100.1.6.2.1.1	PositiveInteger	read-only	A unique identifier for an alarm condition.
tlUpsAlarmInputBad	1.3.6.1.4.1.850.100.1.6.3.13			An input condition is out of tolerance.
tlUpsAlarmInverterCircuitBad	1.3.6.1.4.1.850.100.1.6.3.51			The inverter output is shorted.
tlUpsAlarmInverterOverVoltage	1.3.6.1.4.1.850.100.1.6.3.49			The inverter voltage is too high.
tlUpsAlarmInverterSoftStartBad	1.3.6.1.4.1.850.100.1.6.3.48			The inverter bus voltage cannot reach desired voltage within a specified duration.
tlUpsAlarmInverterUnderVoltage	1.3.6.1.4.1.850.100.1.6.3.50			The inverter voltage is too low.
IP tlUpsAlarmIp	1.3.6.1.4.1.850.100.1.6.2.1.9	IpAddress	read-only	The originating IP address associated with this alarm.
tlUpsAlarmLoadLevelAboveThreshold	1.3.6.1.4.1.850.100.1.6.3.3			The load level is above the designated threshold.
tlUpsAlarmLoadOff	1.3.6.1.4.1.850.100.1.6.3.6			The load is off.
STR tlUpsAlarmLocation	1.3.6.1.4.1.850.100.1.6.2.1.7	DisplayString	read-only	The location of the device on which the alarm is active.
tlUpsAlarmLowBattery	1.3.6.1.4.1.850.100.1.6.3.10			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
STR tlUpsAlarmMac	1.3.6.1.4.1.850.100.1.6.2.1.10	DisplayString	read-only	The originating mac address associated with this alarm.
tlUpsAlarmOnBattery	1.3.6.1.4.1.850.100.1.6.3.9			The UPS is drawing power from the batteries.
tlUpsAlarmOnBypass	1.3.6.1.4.1.850.100.1.6.3.16			The Bypass is presently engaged on the UPS.
tlUpsAlarmOutputBad	1.3.6.1.4.1.850.100.1.6.3.14			An output condition (other than OutputOverload) is out of tolerance.
tlUpsAlarmOutputCurrentChanged	1.3.6.1.4.1.850.100.1.6.3.4			The output current changed from its last known value.
tlUpsAlarmOutputOffAsRequested	1.3.6.1.4.1.850.100.1.6.3.18			The UPS has shutdown as requested, i.e., the output is off.
tlUpsAlarmOutputOverload	1.3.6.1.4.1.850.100.1.6.3.15			The output load exceeds the UPS output capacity.
tlUpsAlarmOverCharged	1.3.6.1.4.1.850.100.1.6.3.56			The UPS is over charged.
tlUpsAlarmOverTemperatureProtection	1.3.6.1.4.1.850.100.1.6.3.55			The over temperature protection is activated.
tlUpsAlarmPrimaryPowerOutage	1.3.6.1.4.1.850.100.1.6.3.1			The primary power source is not present.
tlUpsAlarmRuntimeBelowWarningLevel	1.3.6.1.4.1.850.100.1.6.3.43			The battery seconds remaining is below warning level.
tlUpsAlarmSecondaryPowerOutage	1.3.6.1.4.1.850.100.1.6.3.2			The secondary power source is not present.
tlUpsAlarmShutdownImminent	1.3.6.1.4.1.850.100.1.6.3.30			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
tlUpsAlarmShutdownPending	1.3.6.1.4.1.850.100.1.6.3.29			A upsShutdownAfterDelay countdown is underway.
tlUpsAlarmSiteWiringFault	1.3.6.1.4.1.850.100.1.6.3.54			The utility input wiring is faulty.
tlUpsAlarmSmartBatteryCommLost	1.3.6.1.4.1.850.100.1.6.3.61			Communications with the smart batteries was lost.
tlUpsAlarmSourceAOutage	1.3.6.1.4.1.850.100.1.6.3.62			Input power source A is not present.
tlUpsAlarmSourceBOutage	1.3.6.1.4.1.850.100.1.6.3.63			Input power source B is not present.
G32 tlUpsAlarmsPresentEx	1.3.6.1.4.1.850.100.1.6.1	Gauge32	read-only	The present number of active alarm conditions.
tlUpsAlarmTable	1.3.6.1.4.1.850.100.1.6.2		not-accessible	A list of alarm table entries.
tlUpsAlarmTempBad	1.3.6.1.4.1.850.100.1.6.3.12			A temperature is out of tolerance.
tlUpsAlarmTestInProgress	1.3.6.1.4.1.850.100.1.6.3.31			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
TIM tlUpsAlarmTime	1.3.6.1.4.1.850.100.1.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected.
tlUpsAlarmUpsOffAsRequested	1.3.6.1.4.1.850.100.1.6.3.19			The entire UPS has shutdown as commanded.
tlUpsAlarmUpsOutputOff	1.3.6.1.4.1.850.100.1.6.3.21			The output of the UPS is in the off state.
tlUpsAlarmUpsSystemOff	1.3.6.1.4.1.850.100.1.6.3.22			The UPS system is in the off state.
tlUpsAlarmUserDefined	1.3.6.1.4.1.850.100.1.6.3.7			A user-defined event is in alarm.
tlUpsAlarmWatchdogReset	1.3.6.1.4.1.850.100.1.6.3.64			The internal watchdog triggered a reset of the device.
tlUpsBattery	1.3.6.1.4.1.850.100.1.2
STR tlUpsBatteryAge	1.3.6.1.4.1.850.100.1.2.1	DisplayString	read-only	The age of the battery in years. This is equal to the current date minus tlConfigBattReplDate.
tlUpsConfig	1.3.6.1.4.1.850.100.1.9
STR tlUpsConfigBattReplDate	1.3.6.1.4.1.850.100.1.9.1	DisplayString	read-write	The date on which the battery was last replaced, in the format YYYYMMDD.
INT tlUpsConfigDisplayUnits	1.3.6.1.4.1.850.100.1.9.4	INTEGER	read-write	Selects English or Metric display for all readings. This selection may not be available on all devices. Further, some devices may support this selection, but not via a software selector. In this latter case, selections must be performed on the device itself.
STR tlUpsConfigExternalBattReplDate	1.3.6.1.4.1.850.100.1.9.5	DisplayString	read-write	The date on which the external battery was last replaced, in the format YYYYMMDD.
tlUpsControl	1.3.6.1.4.1.850.100.1.8
T/F tlUpsControlRamp	1.3.6.1.4.1.850.100.1.8.3.2	TruthValue	read-write	Set to TRUE to initiate Ramp
T/F tlUpsControlSelfTest	1.3.6.1.4.1.850.100.1.8.3.1	TruthValue	read-write	Set to TRUE to initiate Self Test
T/F tlUpsControlShed	1.3.6.1.4.1.850.100.1.8.3.3	TruthValue	read-write	Set to TRUE to initiate Shed
T/F tlUpsControlUpsOff	1.3.6.1.4.1.850.100.1.8.3.5	TruthValue	read-write	Set to TRUE to turn UPS off
T/F tlUpsControlUpsOn	1.3.6.1.4.1.850.100.1.8.3.4	TruthValue	read-write	Set to TRUE to turn UPS on
tlUpsEnvironment	1.3.6.1.4.1.850.100.1.13
STR tlUpsExternalBatteryAge	1.3.6.1.4.1.850.100.1.2.3	DisplayString	read-only	The age of external battery in years. This is equal to the current date minus tlConfigExternalBattReplDate.
tlUpsFullAlarmGroup	1.3.6.1.4.1.850.20.2.3.100.6
tlUpsFullAlarmObjsGroup	1.3.6.1.4.1.850.20.2.3.100.6.1			The tlUpsFullAlarmObjsGroup defines objects which are common to the Alarm group of fully compliant Tripplite UPS's
tlUpsFullBatteryGroup	1.3.6.1.4.1.850.20.2.3.100.2			The tlUpsFullBatteryGroup defines objects which are common to the Battery group of fully compliant Tripplite UPS's
tlUpsFullConfigGroup	1.3.6.1.4.1.850.20.2.3.100.9			The tlUpsFullConfigGroup defines objects which are common to the Config group of fully compliant Tripplite UPS's
tlUpsFullControlGroup	1.3.6.1.4.1.850.20.2.3.100.8			The tlUpsFullControlGroup defines objects which are common to the Control group of fully compliant Tripplite UPS's
tlUpsFullGroups	1.3.6.1.4.1.850.20.2.3.100
tlUpsFullIdentGroup	1.3.6.1.4.1.850.20.2.3.100.1			The tlUpsFullIdentGroup defines objects which are common to the Ident group of fully compliant Tripplite UPS's
tlUpsFullOutletGroup	1.3.6.1.4.1.850.20.2.3.100.10			The tlUpsFullOutletGroup defines objects which are common to the Outlet group of fully compliant Tripplite UPS's
tlUpsFullTestGroup	1.3.6.1.4.1.850.20.2.3.100.7			The tlUpsFullTestGroup defines objects which are common to the Test group of fully compliant Tripplite UPS's
tlUpsIdent	1.3.6.1.4.1.850.100.1.1
I32 tlUpsIdentID	1.3.6.1.4.1.850.100.1.1.3	Integer32	read-write	A user-supplied ID for the UPS.
STR tlUpsIdentSerialNum	1.3.6.1.4.1.850.100.1.1.2	DisplayString	read-only	Serial number for the UPS.
I32 tlUpsIdentUpsSoftwareChecksum	1.3.6.1.4.1.850.100.1.1.1	Integer32	read-only	A checksum for the UPS software.
tlUpsInput	1.3.6.1.4.1.850.100.1.3
NUM tlUpsInputNumVoltages	1.3.6.1.4.1.850.100.1.3.1	NonNegativeInteger	read-only	The number of input voltages. Phase to phase or phase to neutral. This variable indicates the number of rows in the input table.
INT tlUpsInputSourceAvailability	1.3.6.1.4.1.850.100.1.3.5	INTEGER	read-only	The determination as to which of two AC input lines are available. The agent will return either inputSourceA(1) or inputSourceB(2) if only one line is available, or inputSourceAB(3) if both lines are available. The agent will never return none(0) since the device will be powered off if neither line is available.
INT tlUpsInputSourceInUse	1.3.6.1.4.1.850.100.1.3.6	INTEGER	read-only	The determination as to which one of two AC input lines is in use.
INT tlUpsInputSourceSelect	1.3.6.1.4.1.850.100.1.3.3	INTEGER	read-write	The determination as to which of two AC input lines is designated as the primary input source. The other is designated as the secondary input source. This value will always return inputSourceA(0) for devices with a single input source. Setting this value is supported only on selected models.
NUM tlUpsInputSourceTransitionCount	1.3.6.1.4.1.850.100.1.3.7	PositiveInteger	read-only	The number of times the device transitions between primary and secondary sources. Most devices are limied to 65533 transitions, after which the value will not increment.
NUM tlUpsInputVoltage	1.3.6.1.4.1.850.100.1.3.2.1.3	NonNegativeInteger	read-only	The magnitude of the present input voltage. A value of 6553 indicates Unknown.
tlUpsInputVoltageEntry	1.3.6.1.4.1.850.100.1.3.2.1		not-accessible	An entry containing information applicable to a particular input voltage.
NUM tlUpsInputVoltageIndex	1.3.6.1.4.1.850.100.1.3.2.1.1	PositiveInteger	not-accessible	The input voltage identifier.
tlUpsInputVoltageTable	1.3.6.1.4.1.850.100.1.3.2		not-accessible	A list of voltage input table entries. The number of entries is given by the value of tlUpsInputNumVoltages.
INT tlUpsInputVoltageType	1.3.6.1.4.1.850.100.1.3.2.1.2	INTEGER	read-only	Whether voltage measured is phase to phase or phase to neutral.
STR tlUpsLocation	1.3.6.1.4.1.850.100.1.1.6	DisplayString	read-write	The device location string.
tlUpsMainOutlet	1.3.6.1.4.1.850.100.1.12
INT tlUpsMainOutletControl	1.3.6.1.4.1.850.100.1.12.3	INTEGER	read-write	Controls the state of the main outlet of the device.
T/F tlUpsMainOutletControllable	1.3.6.1.4.1.850.100.1.12.2	TruthValue	read-only	Indicates if this device has controllable outlets
INT tlUpsMainOutletState	1.3.6.1.4.1.850.100.1.12.1	INTEGER	read-only	The current state of the main output of the device.
tlUpsObjects	1.3.6.1.4.1.850.100.1
tlUpsOutlet	1.3.6.1.4.1.850.100.1.10
INT tlUpsOutletControl	1.3.6.1.4.1.850.100.1.10.2.1.4	INTEGER	read-write	Controls the state of the Outlet.
NUM tlUpsOutletCurrent	1.3.6.1.4.1.850.100.1.10.2.1.13	PositiveInteger	read-only	The value of this outlet's current, represented as 0.1A.
tlUpsOutletEntry	1.3.6.1.4.1.850.100.1.10.2.1		not-accessible	An entry containing Outlet information applicable to a particular device managed by this agent.
tlUpsOutletGroup	1.3.6.1.4.1.850.100.1.11
INT tlUpsOutletGroupControl	1.3.6.1.4.1.850.100.1.11.2.1.6	INTEGER	read-write	Controls the state of every outlet associated with the group.
STR tlUpsOutletGroupDesc	1.3.6.1.4.1.850.100.1.11.2.1.4	DisplayString	read-write	A description for this outlet group.
tlUpsOutletGroupEntry	1.3.6.1.4.1.850.100.1.11.2.1		not-accessible	An entry containing outlet group information applicable to a particular device managed by this agent
NUM tlUpsOutletGroupIndex	1.3.6.1.4.1.850.100.1.11.2.1.1	PositiveInteger	read-only	This is the index number of this load group for the device.
STR tlUpsOutletGroupName	1.3.6.1.4.1.850.100.1.11.2.1.3	DisplayString	read-write	The name of this outlet group.
I32 tlUpsOutletGroupNdx	1.3.6.1.4.1.850.100.1.10.2.1.12	Integer32	read-write	tlUpsOutletGroupIndex of corresponding outlet group, or 0 if ungrouped.
ROW tlUpsOutletGroupRowStatus	1.3.6.1.4.1.850.100.1.11.2.1.2	RowStatus	read-write	Row status for the tlUpsOutletGroupTable
INT tlUpsOutletGroupState	1.3.6.1.4.1.850.100.1.11.2.1.5	INTEGER	read-only	The current state of the outlet group.
tlUpsOutletGroupTable	1.3.6.1.4.1.850.100.1.11.2		not-accessible	A list of device outlet group entries. The number of entries is given by the value of tlUpsOutletNumOutletGroups.
NUM tlUpsOutletIndex	1.3.6.1.4.1.850.100.1.10.2.1.1	PositiveInteger	read-only	This is the index number of this Outlet for the device indicated by tlDeviceIndex.
STR tlUpsOutletName	1.3.6.1.4.1.850.100.1.10.2.1.5	DisplayString	read-write	A string identifying the devices attached to the output(s) of the device.
NUM tlUpsOutletNumOutletGroups	1.3.6.1.4.1.850.100.1.11.1	NonNegativeInteger	read-only	The number of available Outlet Groups in this device.
NUM tlUpsOutletNumOutlets	1.3.6.1.4.1.850.100.1.10.1	NonNegativeInteger	read-only	The number of available Outlets in this device.
NUM tlUpsOutletPower	1.3.6.1.4.1.850.100.1.10.2.1.14	PositiveInteger	read-only	The value of this outlet's power in watts.
INT tlUpsOutletRampAction	1.3.6.1.4.1.850.100.1.10.2.1.6	INTEGER	read-write	The ramp action to take on the Outlet.
I32 tlUpsOutletRampData	1.3.6.1.4.1.850.100.1.10.2.1.8	Integer32	read-write	The data value associated with type of ramp data.
INT tlUpsOutletRampDataType	1.3.6.1.4.1.850.100.1.10.2.1.7	INTEGER	read-write	The type of data associated with ramp action.
INT tlUpsOutletShedAction	1.3.6.1.4.1.850.100.1.10.2.1.9	INTEGER	read-write	The shed action to take on the Outlet.
I32 tlUpsOutletShedData	1.3.6.1.4.1.850.100.1.10.2.1.11	Integer32	read-write	The data value associated with type of shed data.
INT tlUpsOutletShedDataType	1.3.6.1.4.1.850.100.1.10.2.1.10	INTEGER	read-write	The type of data associated with shed action.
INT tlUpsOutletState	1.3.6.1.4.1.850.100.1.10.2.1.2	INTEGER	read-only	The current state of the Outlet.
tlUpsOutletTable	1.3.6.1.4.1.850.100.1.10.2		not-accessible	A list of all device Outlets for all devices.
I32 tlUpsOutletType	1.3.6.1.4.1.850.100.1.10.2.1.3	Integer32	read-only	This is a bit field that indicates the type of this Outlet. When 0, the outlet is not controllable and has none of the other features indicated in the bit map. When non-zero, the features present for this outlet can be interpreted with the definition. Bit Display 0 Reserved, may be 1 or 0 1 Controllable 2 3 4 5 6 7 8 9 10 11 12 13 14 15
tlUpsOutput	1.3.6.1.4.1.850.100.1.4
tlUpsOutputCircuitEntry	1.3.6.1.4.1.850.100.1.4.7.1		not-accessible	An entry containing information applicable to a particular output circuit.
NUM tlUpsOutputCircuitIndex	1.3.6.1.4.1.850.100.1.4.7.1.1	PositiveInteger	not-accessible	The output circuit identifier.
NUM tlUpsOutputCircuitLoadCurrent	1.3.6.1.4.1.850.100.1.4.7.1.3	NonNegativeInteger	read-only	The magnitude of the present output current in tenths of an amp. A value of 65534 indicates Unknown.
NUM tlUpsOutputCircuitPower	1.3.6.1.4.1.850.100.1.4.7.1.5	NonNegativeInteger	read-only	The magnitude of the present power in watts. tenths of an amp.
NUM tlUpsOutputCircuitPowerFactor	1.3.6.1.4.1.850.100.1.4.7.1.6	NonNegativeInteger	read-only	The power factor of all receptacles in a given circuit as a %.
NUM tlUpsOutputCircuits	1.3.6.1.4.1.850.100.1.4.6	NonNegativeInteger	read-only	The number of output circuits. This variable indicates the number of rows in the output circuit table.
INT tlUpsOutputCircuitStatus	1.3.6.1.4.1.850.100.1.4.7.1.2	INTEGER	read-only	Whether the breaker is open or closed.
tlUpsOutputCircuitTable	1.3.6.1.4.1.850.100.1.4.7		not-accessible	A list of output currents table entries. The number of entries is given by the value of tlUpsOutputNumCircuits.
NUM tlUpsOutputCircuitVoltage	1.3.6.1.4.1.850.100.1.4.7.1.4	NonNegativeInteger	read-only	The magnitude of the present circuit voltage in tenths of an volt.
NUM tlUpsOutputPowerTotal	1.3.6.1.4.1.850.100.1.4.5	PositiveInteger	read-only	The power capacity of the device.
INT tlUpsPhaseImbalance	1.3.6.1.4.1.850.100.1.3.4	INTEGER	read-only	Percentage of imbalance of the 3 phases.
I32 tlUpsSelectedDeviceID	1.3.6.1.4.1.850.100.1.1.5	Integer32	read-write	The device ID selected to be used for retrieving data for this mib. As the snmp web card has only one device, this is read only for it
STR tlUpsSnmpCardSerialNum	1.3.6.1.4.1.850.100.1.1.4	DisplayString	read-only	Serial number for the UPS.
I32 tlUpsTemperature	1.3.6.1.4.1.850.100.1.13.1	Integer32	read-only	The ambient temperature. The measurement returned will either be in units of Celsius (C) or Fahrenheit (F) depending upon whether Metric or English was selected for the reading by tlUpsConfigDisplayUnits.
I32 tlUpsTemperatureF	1.3.6.1.4.1.850.100.1.2.2	Integer32	read-only	The temperature of the battery, in Farenheight degrees. This is calculated from upsBatteryTemperature, which is in Celsius degrees.
tlUpsTest	1.3.6.1.4.1.850.100.1.7
STR tlUpsTestDate	1.3.6.1.4.1.850.100.1.7.1	DisplayString	read-only	The date of the last self-test run on the ups, in the format YYYYMMDD.
STR tlUpsTestResultsDetail	1.3.6.1.4.1.850.100.1.7.2	DisplayString	read-only	Result of the last self-test run on the ups.
NTF tlUpsTrapAlarmEntryAdded	1.3.6.1.4.1.850.100.2.3			This trap is sent each time an alarm is inserted into to the alarm table.
NTF tlUpsTrapAlarmEntryAddedV1	1.3.6.1.4.1.850.100.2.0.3			This trap is sent each time an alarm is inserted into to the alarm table.
NTF tlUpsTrapAlarmEntryRemoved	1.3.6.1.4.1.850.100.2.4			This trap is sent each time an alarm is removed from the alarm table.
NTF tlUpsTrapAlarmEntryRemovedV1	1.3.6.1.4.1.850.100.2.0.4			This trap is sent each time an alarm is removed from the alarm table.
tlUpsTraps	1.3.6.1.4.1.850.100.2
NTF tlUpsTrapSystemShutdown	1.3.6.1.4.1.850.100.2.6			Used to inform another entity of an engine's startup. The varbinds that follow are: OBJ1 = tlEngineType Obj1Value = The type of engine providing this data OBJ2 = tlEngineSoftwareVersion Obj2Value = The current version of the engine OBJ3 = tlEngineMACAddr Obj3Value = The MAC address of the engine OBJ4 = tlUpsSnmpCardSerialNum Obj4Value = The serial number of the SNMPWEBCARD [should be 0 on PC] --- if this trap is extended, place all static OIDs above this mark. all objects below --- the number of devices (tlNumDevices) is explicit as per device for enumeration by --- the target receiver OBJ5 = tlNumDevices Obj5Value = The number of devices attached --- The following objects will be replicated per each device: OBJ6 = The OID for an entry of tlDevManufacturer, indexed by device Obj6Value = The device's manufacturer OBJ7 = The OID for an entry of tlDevModel, indexed by device Obj7Value = The device's model name OBJ8 = The OID for an entry of tlDevName, indexed by device Obj8Value = The device's display name OBJ9 = The OID for an entry of tlDevLocation, indexed by device Obj9Value = The device's location OBJ10 = The OID for an entry of tlDevRegion, indexed by device Obj10Value= The device's region OBJ11 = The OID for an entry of tlDevProtocol, indexed by device Obj11Value= The device's protocol (display string format)
NTF tlUpsTrapSystemStartup	1.3.6.1.4.1.850.100.2.5			Used to inform another entity of an engine's startup. The varbinds that follow are: OBJ1 = tlEngineType Obj1Value = The type of engine providing this data OBJ2 = tlEngineSoftwareVersion Obj2Value = The current version of the engine OBJ3 = tlEngineMACAddr Obj3Value = The MAC address of the engine OBJ4 = tlUpsSnmpCardSerialNum Obj4Value = The serial number of the SNMPWEBCARD [should be 0 on PC] --- if this trap is extended, place all static OIDs above this mark. all objects below --- the number of devices (tlNumDevices) is explicit as per device for enumeration by --- the target receiver OBJ5 = tlNumDevices Obj5Value = The number of devices attached --- The following objects will be replicated per each device: OBJ6 = The OID for an entry of tlDevManufacturer, indexed by device Obj6Value = The device's manufacturer OBJ7 = The OID for an entry of tlDevModel, indexed by device Obj7Value = The device's model name OBJ8 = The OID for an entry of tlDevName, indexed by device Obj8Value = The device's display name OBJ9 = The OID for an entry of tlDevLocation, indexed by device Obj9Value = The device's location OBJ10 = The OID for an entry of tlDevRegion, indexed by device Obj10Value= The device's region OBJ11 = The OID for an entry of tlDevProtocol, indexed by device Obj11Value= The device's protocol (display string format)
NUM tlUpsWatchdogSecsBeforeReboot	1.3.6.1.4.1.850.100.1.8.2	NonNegativeInteger	read-write	The maximum number of seconds that can expire between polls that the engine makes to the UPS for data. If this time runs out, then the UPS will cycle its outputs. Set this to zero to turns disable this feature.
T/F tlUpsWatchdogSupported	1.3.6.1.4.1.850.100.1.8.1	TruthValue	read-only	Indicates whether or not this UPS supports a watchdog reboot.
tlUpsWellKnownAlarms	1.3.6.1.4.1.850.100.1.6.3
tlUpsWellKnownControls	1.3.6.1.4.1.850.100.1.8.3
ultrix	1.3.6.1.4.1.850.2.1.5
unknown	1.3.6.1.4.1.850.2.1.255
win32	1.3.6.1.4.1.850.2.1.13
win9x	1.3.6.1.4.1.850.2.1.50
winnt	1.3.6.1.4.1.850.2.1.51

RFC description

Tripp Lite PowerAlert UPS and power management including input sources, output circuits, and power monitoring.

Start monitoring Tripp Lite UPS, power distribution unit (PDU), PowerAlert-managed (email/SNMP contact config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TRIPPLITE-12X