TRIPPUPS1-MIB

All MIBs › TRIPPUPS1-MIB

Category: Tripp Lite Power Management, UPS and Power Management

Description: Monitors Tripp Lite UPS units including battery status, input voltage, load percentage, and fault conditions.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TRIPPUPS1-MIB?

TRIPPUPS1-MIB is a Tripp Lite vendor MIB for managing and monitoring Tripp Lite uninterruptible power supply (UPS) units, covering battery condition, input power quality, output load, and configurable fault thresholds. It exposes battery temperature, configured input-voltage high/low thresholds, output percent-load-high threshold, battery percent-low threshold, and battery temperature-high threshold, alongside broader UPS identity, battery, and input group objects. This is fundamentally a power/hardware-health monitoring MIB: it lets an administrator track battery health (temperature, charge level) and utility input voltage quality, and detect an overload condition via output load percentage, all central to preventing unplanned shutdowns from UPS or battery failure. It follows the general structure of the standard UPS-MIB (RFC 1628) naming conventions (upsBattery, upsInput, upsIdent groups) suggesting a close conceptual alignment with, if not direct reuse of, that IETF standard. It is typically deployed on Tripp Lite UPS units protecting servers, network closets, or other critical infrastructure requiring backup power monitoring. Engineers can download the TRIPPUPS1-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TRIPPUPS1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Tripp Lite uninterruptible power supply (UPS) units

Monitoring Examples

An operator would poll upsBatteryTemperature and compare it against upsConfigBatteryTemperatureHigh to detect an overheating battery, and check upsConfigInputVoltageHigh/upsConfigInputVoltageLow thresholds against the live input voltage reading to spot utility power quality issues. A load reading approaching upsConfigOutputPercLoadHigh combined with upsConfigBatteryPercLow being crossed would reveal the UPS is both overloaded and running low on battery reserve, a strong signal of imminent shutdown risk during a power event.

What Can Be Monitored

battery temperature
battery charge percentage vs. low threshold
output load percentage vs. high threshold
input voltage vs. high/low thresholds

Imported Objects

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
OBJECT-TYPE
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
tripplite	1.3.6.1.4.1.850
NTF upsOnBattery	1.3.6.1.4.1.850.0.5			The UPS is on battery.
NTF powerRestored	1.3.6.1.4.1.850.0.6			Utility power has been restored.
NTF lowBattery	1.3.6.1.4.1.850.0.7			The UPS batteries are low and will soon be exhausted.
NTF returnFromLowBattery	1.3.6.1.4.1.850.0.8			The UPS has returned from a low battery condition.
NTF communicationEstablished	1.3.6.1.4.1.850.0.9			Communication with the UPS has been established. This trap will be sent each time there is a transition from a power off condition to a power on condition.
NTF communicationLost	1.3.6.1.4.1.850.0.10			Communication with the UPS has been lost.
NTF upsOverload	1.3.6.1.4.1.850.0.11			The UPS has sensed a load greater than the value of the upsConfigOutputPercLoadHigh MIB variable.
NTF upsDiagnosticsFailed	1.3.6.1.4.1.850.0.12			The UPS failed its self-test.
NTF upsDiagnosticsPassed	1.3.6.1.4.1.850.0.13			The UPS passed its internal self-test.
NTF utilityVoltageHigh	1.3.6.1.4.1.850.0.14			The UPS input voltage greater than or equal to the value of the upsConfigInputVoltageHigh MIB variable.
NTF utilityVoltageLow	1.3.6.1.4.1.850.0.15			The UPS input voltage is less than or equal to the value of the upsConfigInputVoltageLow MIB variable.
NTF utilityVoltageReturnToNormal	1.3.6.1.4.1.850.0.16			The UPS has returned from a utility voltage high or low condition.
NTF batteryTemperatureHigh	1.3.6.1.4.1.850.0.17			The UPS battery temperature has exceeded the value of the upsConfigBatteryTemperatureHigh MIB variable.
NTF shutdownPending	1.3.6.1.4.1.850.0.18			A UPS shutdown countdown is underway.
NTF upsSleeping	1.3.6.1.4.1.850.0.19			The output of the UPS has been turned off.
NTF upsWokeup	1.3.6.1.4.1.850.0.20			The output of the UPS has been turned on.
NTF upsBatteryNeedsReplacement	1.3.6.1.4.1.850.0.21			The UPS battery needs to be replaced.
trippUPS1	1.3.6.1.4.1.850.1
ups	1.3.6.1.4.1.850.1.1
upsIdent	1.3.6.1.4.1.850.1.1.1
STR upsIdentManufacturer	1.3.6.1.4.1.850.1.1.1.1	DisplayString	read-only	The name of the UPS manufacturer.
STR upsIdentModel	1.3.6.1.4.1.850.1.1.1.2	DisplayString	read-only	The UPS Model designation.
STR upsIdentUPSSoftwareVersion	1.3.6.1.4.1.850.1.1.1.3	DisplayString	read-only	The UPS Firmware software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.
STR upsIdentAgentSoftwareVersion	1.3.6.1.4.1.850.1.1.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.
STR upsIdentName	1.3.6.1.4.1.850.1.1.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.
STR upsIdentAttachedDevices	1.3.6.1.4.1.850.1.1.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.
upsBattery	1.3.6.1.4.1.850.1.1.2
INT upsBatteryStatus	1.3.6.1.4.1.850.1.1.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the batteries are fully charged. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigMinutesRemaining. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost.
INT upsSecondsOnBattery	1.3.6.1.4.1.850.1.1.2.2	INTEGER	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power. UNITS - seconds
INT upsEstimatedMinutesRemaining	1.3.6.1.4.1.850.1.1.2.3	INTEGER	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power were to be lost and remain off. UNITS - minutes
INT upsBatteryChargeRemaining	1.3.6.1.4.1.850.1.1.2.4	INTEGER	read-only	The estimate of the battery charge remaining expressed as a percent of full charge.
INT upsBatteryVoltage	1.3.6.1.4.1.850.1.1.2.5	INTEGER	read-only	The magnitude of the present battery voltage. UNITS 0.1 Volt DC.
INT upsBatteryTemperature	1.3.6.1.4.1.850.1.1.2.7	INTEGER	read-only	The ambient temperature at or near the UPS Battery. UNITS degrees Centigrade
upsInput	1.3.6.1.4.1.850.1.1.3
INT upsInputFrequency	1.3.6.1.4.1.850.1.1.3.1	INTEGER	read-only	The present input frequency. UNITS 0.1 Hertz
CTR upsInputLineBads	1.3.6.1.4.1.850.1.1.3.2	Counter	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer.
INT upsInputNumLines	1.3.6.1.4.1.850.1.1.3.3	INTEGER	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.
INT upsInputVolt	1.3.6.1.4.1.850.1.1.3.4	INTEGER	read-only	The magnitude of the present input voltage. UNITS RMS Volts
upsInputTable	1.3.6.1.4.1.850.1.1.3.5		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.
upsInputEntry	1.3.6.1.4.1.850.1.1.3.5.1		not-accessible	An entry containing information applicable to a particular input line.
INT upsInputLineIndex	1.3.6.1.4.1.850.1.1.3.5.1.1	INTEGER	read-only	The input line identifier.
INT upsInputVoltage	1.3.6.1.4.1.850.1.1.3.5.1.2	INTEGER	read-only	The magnitude of the present input voltage. UNITS RMS Volts
upsOutput	1.3.6.1.4.1.850.1.1.4
INT upsOutputSource	1.3.6.1.4.1.850.1.1.4.1	INTEGER	read-only	The present source of output power.
INT upsOutputFrequency	1.3.6.1.4.1.850.1.1.4.2	INTEGER	read-only	The present output frequency. UNITS 0.1 Hertz
INT upsOutputNumLines	1.3.6.1.4.1.850.1.1.4.3	INTEGER	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.
INT upsOutputPercLoad	1.3.6.1.4.1.850.1.1.4.4	INTEGER	read-only	The percentage of true power capacity presently being used. UNITS percent
upsOutputTable	1.3.6.1.4.1.850.1.1.4.5		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.
upsOutputEntry	1.3.6.1.4.1.850.1.1.4.5.1		not-accessible	An entry containing information applicable to a particular output line.
INT upsOutputLineIndex	1.3.6.1.4.1.850.1.1.4.5.1.1	INTEGER	read-only	The output line identifier.
INT upsOutputVoltage	1.3.6.1.4.1.850.1.1.4.5.1.2	INTEGER	read-only	The present output voltage. UNITS RMS Volts
INT upsOutputCurrent	1.3.6.1.4.1.850.1.1.4.5.1.3	INTEGER	read-only	The present output mandatory. UNITS 0.1 Amp
INT upsOutputPower	1.3.6.1.4.1.850.1.1.4.5.1.4	INTEGER	read-only	The present output true power. UNITS Watts
INT upsOutputPercentLoad	1.3.6.1.4.1.850.1.1.4.5.1.5	INTEGER	read-only	The percentage of true power capacity presently being used. UNITS percent
upsAlarm	1.3.6.1.4.1.850.1.1.6
GAU upsAlarmsPresent	1.3.6.1.4.1.850.1.1.6.1	Gauge	read-only	The present number of active alarm conditions.
upsAlarmTable	1.3.6.1.4.1.850.1.1.6.4		not-accessible	A list of alarm table entries. The table consists of zero, one, or may rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value fo upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries are in chronological order until upsAlarmId wraps. Alarms are named by and OBJECT IDENTIFIER, upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be take in the definition of the number of active rows in the table at any given time is reflected by the value fo upsAlarms.
upsAlarmEntry	1.3.6.1.4.1.850.1.1.6.4.1		not-accessible	An entry containing information applicable to a particular alarm.
INT upsAlarmID	1.3.6.1.4.1.850.1.1.6.4.1.1	INTEGER	read-only	A unique identifier for an alarm condition. This value must remain constant.
STR upsAlarmDESCR	1.3.6.1.4.1.850.1.1.6.4.1.2	DisplayString	read-only	A reference to an alarm description object. The object references should not be accessible, but rather be used to provide a unique description of the alarm condition.
TIK upsAlarmTime	1.3.6.1.4.1.850.1.1.6.4.1.3	TimeTicks	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumable existed before agent startup, the value of upsAlarmTime shall equal 0.
upsWellKnownAlarms	1.3.6.1.4.1.850.1.1.7
INT upsAlarmBatteryBad	1.3.6.1.4.1.850.1.1.7.1	INTEGER	read-only	One or more batteries have been determined to require replacement.
INT upsAlarmOnBattery	1.3.6.1.4.1.850.1.1.7.2	INTEGER	read-only	The UPS is drawing power from the batteries.
INT upsAlarmLowBattery	1.3.6.1.4.1.850.1.1.7.3	INTEGER	read-only	The remaining battery run-time is less than or equal to upsConfigMinutesRemaining.
INT upsAlarmDepletedBattery	1.3.6.1.4.1.850.1.1.7.4	INTEGER	read-only	The UPS will be unable to sustain the present load when and if the utility power is lost.
INT upsAlarmTempBad	1.3.6.1.4.1.850.1.1.7.5	INTEGER	read-only	A temperature is out of tolerance.
INT upsAlarmOutputOverload	1.3.6.1.4.1.850.1.1.7.6	INTEGER	read-only	The output load exceeds the UPS output capacity.
INT upsAlarmOutputOffAsRequested	1.3.6.1.4.1.850.1.1.7.7	INTEGER	read-only	The UPS has shutdown as commanded, i.e., the output is off.
INT upsAlarmUpsOutputOff	1.3.6.1.4.1.850.1.1.7.8	INTEGER	read-only	The UPS is in the off state.
INT upsAlarmDiagnosticTestFailed	1.3.6.1.4.1.850.1.1.7.9	INTEGER	read-only	The result of the last diagnostic test indicates a failure.
INT upsAlarmCommunicationsLost	1.3.6.1.4.1.850.1.1.7.10	INTEGER	read-only	A problem has been encountered in the communications between the agent and the UPS.
INT upsAlarmShutdownPending	1.3.6.1.4.1.850.1.1.7.11	INTEGER	read-only	A upsShutdownAfterDelay countdown is underway.
INT upsAlarmShutdownImminent	1.3.6.1.4.1.850.1.1.7.12	INTEGER	read-only	A upsShutdownAfterDelay countdown is underway.
INT upsAlarmTestInProgress	1.3.6.1.4.1.850.1.1.7.13	INTEGER	read-only	A upsShutdownAfterDelay countdown is underway.
upsTest	1.3.6.1.4.1.850.1.1.8
INT upsTestId	1.3.6.1.4.1.850.1.1.8.1	INTEGER	read-write	The test named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of test, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. Tests in progress may be aborted by setting this variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has bee run, in which case the well known value upsTestNoTestsInitiated is returned.
INT upsTestResultsSummary	1.3.6.1.4.1.850.1.1.8.2	INTEGER	read-only	The results of the mandatory or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) are self-documenting. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(4) indicates that no previous test results are available, such as in the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non-volatile storage of test results.
upsControl	1.3.6.1.4.1.850.1.1.9
INT upsShutdownType	1.3.6.1.4.1.850.1.1.9.1	INTEGER	read-write	Setting this object will start the output after the indicated number of seconds. Setting this object to 0 will cause the UPS to start the output immediately. If the output is already on at the time the delay has counted down, nothing will happen.
INT upsShutdownAfterDelay	1.3.6.1.4.1.850.1.1.9.2	INTEGER	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShhutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect. UNITS seconds
INT upsStartupAfterDelay	1.3.6.1.4.1.850.1.1.9.3	INTEGER	read-write	Setting this object will start the output after the indicated number of seconds, includeing starting the UPS, if necessary. Setting this object to 0 will cause the start to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until start, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall depend upon the value of upsAutoRestart at that time. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted. UNITS seconds
INT upsRebootDuration	1.3.6.1.4.1.850.1.1.9.4	INTEGER	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of the upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall depend on the value of upsAutoRestart at that time. UNITS seconds
INT upsAutoRestart	1.3.6.1.4.1.850.1.1.9.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if/when utility power is present.
upsConfig	1.3.6.1.4.1.850.1.1.10
INT upsConfigInputVoltageHigh	1.3.6.1.4.1.850.1.1.10.11	INTEGER	read-write	If the value of the input voltage (in Volts) exceeds this value, a utilityVoltageHigh trap will be triggered.
INT upsConfigInputVoltageLow	1.3.6.1.4.1.850.1.1.10.12	INTEGER	read-write	If the value of the input voltage (in Volts) falls below this value, a utilityVoltageLow trap will be triggered.
INT upsConfigOutputPercLoadHigh	1.3.6.1.4.1.850.1.1.10.13	INTEGER	read-write	If the value of the output percent load exceeds this value, a upsOverload trap will be triggered.
INT upsConfigBatteryPercLow	1.3.6.1.4.1.850.1.1.10.14	INTEGER	read-write	If the value of the battery percent capacity falls below this value, a lowBattery trap will be triggered.
INT upsConfigBatteryTemperatureHigh	1.3.6.1.4.1.850.1.1.10.15	INTEGER	read-write	If the value of the battery temperature exceeds this value, a batteryTemperatureHigh trap will be triggered.

RFC description

A Tripp Lite MIB for managing Uninterruptible Power Supply (UPS) systems via SNMP. This MIB includes objects related to UPS control, configuration, battery status, reboot duration, and alarm states.

Start monitoring Tripp Lite uninterruptible power supply (UPS) units (battery temperature/input-voltage/output-load status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TRIPPUPS1-MIB

What Is TRIPPUPS1-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description