All MIBs › SPC200
Organization: Organization
Last Updated: 2004-12-17
Category: Generic / Unclassified
Description: Manages SPC200 device configuration, I/O state, and operational parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SPC200?
SPC200 appears to be a vendor-specific MIB for a powerline communication (PLC) network adapter/bridge, based on its "plc"-prefixed object identifiers for BSS (network) role identification and synchronization band settings. It exposes configuration data for the device's powerline network role (master/slave BSS ID), spy/synchronization band settings, dynamic IP assignment, and extended Ethernet interface parameters such as default speed and auto-negotiation status. Monitoring this MIB lets an administrator confirm the operational status of the device's powerline and Ethernet interfaces, including whether the unit is acting as a master or slave node and whether its network settings (BSS ID, sync band) are correctly and dynamically assigned. The MIB extends standard IF-MIB interface objects (ifTableExt/ifEntryExt) rather than duplicating them, showing a dependency on the IETF Interfaces MIB for baseline interface data. It would typically be deployed in home or small-office powerline networking installations where an SPC200-based adapter bridges Ethernet traffic over household electrical wiring. Engineers can download the SPC200 file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SPC200. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- powerline communication (PLC) network adapter/bridge
Monitoring Examples
Polling plcMasterBssId or plcSlaveBssId tells an admin whether the SPC200 unit is configured as the master or slave node of its powerline network segment, while plcSpyIsDynamic and plcStaticSpySynchBandNb reveal whether synchronization band assignment is automatic or fixed. The extended interface objects (ifDefaultSpeed/ifSpeedAutoNegAdminStatus extensions) show whether the Ethernet-facing port is auto-negotiating correctly; a mismatch here combined with an unexpected plcBssId would indicate a misconfigured or isolated powerline node.
What Can Be Monitored
- master/slave BSS role
- synchronization band configuration
- dynamic vs static IP assignment
- Ethernet interface speed and auto-negotiation
- powerline network node identity
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
| interfaces | OBJECT-IDENTITY |
From SNMPv2-CONF
| AGENT-CAPABILITIES | |
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From SPIDCOM-MIB
| spidcom | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using bootstatsBoot OID:
Select a powerline communication (PLC) network adapter/bridge (master/slave BSS role, sync-band/Ethernet interface status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type bootstatsBoot into the Find box to locate it in the OID tree, then select it and click OK. It reports the boot. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| spc200MIB | 1.3.6.1.4.1.22764.1 | Description | ||
| plc | 1.3.6.1.4.1.22764.1.1 | |||
| stats | 1.3.6.1.4.1.22764.1.1.1 | |||
| portStatsTable | 1.3.6.1.4.1.22764.1.1.1.2 | not-accessible | This table gathers all statistic data specific to SPC200 chip relative to plc connection. | |
| portStatsEntry | 1.3.6.1.4.1.22764.1.1.1.2.1 | not-accessible | This row contains statistic data specific to SPC200 chip relative to a connection. | |
| BAN portStatsBandIndex | 1.3.6.1.4.1.22764.1.1.1.2.1.1 | BandValue | not-accessible | The band number on which the signal, noise, ber data are collected. |
| GRO portStatsGroupIndex | 1.3.6.1.4.1.22764.1.1.1.2.1.2 | GroupValue | not-accessible | The group number on which the signal, noise, ber data are collected |
| CAR portStatsCarrierIndex | 1.3.6.1.4.1.22764.1.1.1.2.1.3 | CarrierValue | not-accessible | The group number on which the signal, noise, ber data are collected |
| C32 portStatsSignal | 1.3.6.1.4.1.22764.1.1.1.2.1.4 | Counter32 | read-only | The DB value of the signal associated with the carrier wave entry. |
| C32 portStatsNoise | 1.3.6.1.4.1.22764.1.1.1.2.1.5 | Counter32 | read-only | The DB value of the noise associated with the carrier wave entry. |
| portStats2Table | 1.3.6.1.4.1.22764.1.1.1.3 | not-accessible | This table gathers all statistic data specific to SPC200 chip relative to plc channels. This table has the same information as the portChannelStatsTable but in a more compact way. This table has been added to deal with possible slow performances. | |
| portStats2Entry | 1.3.6.1.4.1.22764.1.1.1.3.1 | not-accessible | This row contains statistic data specific to SPC200 chip relative to a connection. | |
| OCT portStats2Signal | 1.3.6.1.4.1.22764.1.1.1.3.1.1 | OCTET STRING | read-only | The values of the signal for all the carrier waves. The expected format is VALUE VALUE VALUE ... VALUE. Each value is coded on two bytes. There is one value for each 128 carriers of the considered band. |
| OCT portStats2Noise | 1.3.6.1.4.1.22764.1.1.1.3.1.2 | OCTET STRING | read-only | The values of the noise for all the carrier waves. The expected format is VALUE VALUE VALUE ... VALUE. Each value is coded on two bytes. There is one value for each 128 carriers of the considered band. |
| C32 portStats2AvgBandAtt | 1.3.6.1.4.1.22764.1.1.1.3.1.3 | Counter32 | read-only | Average attenuation per band (dB). |
| C32 portStats2AvgBandSNR | 1.3.6.1.4.1.22764.1.1.1.3.1.4 | Counter32 | read-only | Average SNR per band (dB). |
| portStats3Table | 1.3.6.1.4.1.22764.1.1.1.4 | not-accessible | This table gathers all statistic data specific to SPC200 chip relative to plc channels. This table has the same information as the portChannelStatsTable but in a more compact way. This table has been added to deal with possible slow performances. | |
| portStats3Entry | 1.3.6.1.4.1.22764.1.1.1.4.1 | not-accessible | This row contains statistic data specific to SPC200 chip relative to a connection. | |
| C32 portStats3AvgAtt | 1.3.6.1.4.1.22764.1.1.1.4.1.1 | Counter32 | read-only | Average attenuation on the link (dB). |
| C32 portStats3AvgSNR | 1.3.6.1.4.1.22764.1.1.1.4.1.2 | Counter32 | read-only | Average SNR on the link (dB). |
| bootstats | 1.3.6.1.4.1.22764.1.1.1.5 | boot statistics | ||
| C32 bootstatsBootEx | 1.3.6.1.4.1.22764.1.1.1.5.1 | Counter32 | read-only | Boot |
| C32 bootstatsManualReset | 1.3.6.1.4.1.22764.1.1.1.5.2 | Counter32 | read-only | Manual reset |
| C32 bootstatsFailureReset | 1.3.6.1.4.1.22764.1.1.1.5.3 | Counter32 | read-only | Failure reset |
| plcObjects | 1.3.6.1.4.1.22764.1.1.2 | |||
| PLC plcMode | 1.3.6.1.4.1.22764.1.1.2.1 | PlcModeType | read-write | Plc Mode |
| plcTopo | 1.3.6.1.4.1.22764.1.1.2.2 | |||
| C32 plcTopoChanges | 1.3.6.1.4.1.22764.1.1.2.2.1 | Counter32 | read-only | The total number of topology changes detected by this plc bridge since the management entity was last reset or initialized. Such changes concerns only - the plcBasePortTable rows - the plcBasePortTable columns except for plcBasePortChannelEstimation |
| plcBasePortTable | 1.3.6.1.4.1.22764.1.1.2.2.2 | not-accessible | This table contains the list of plc remote connection | |
| plcBasePortEntry | 1.3.6.1.4.1.22764.1.1.2.2.2.1 | not-accessible | This row contains plc remote connection information | |
| MAC plcBasePortIndex | 1.3.6.1.4.1.22764.1.1.2.2.2.1.1 | MacAddress | not-accessible | The MAC address of the MAC layer above the plc interface of the remote PLC equipment. |
| MAC plcBasePortAddress | 1.3.6.1.4.1.22764.1.1.2.2.2.1.2 | MacAddress | read-only | The MAC address of the MAC layer above the plc interface of the remote PLC equipment. |
| EST plcBasePortChannelEstimation | 1.3.6.1.4.1.22764.1.1.2.2.2.1.3 | EstimationMode | read-write | Enable or disable the automatic channel estimation processus. |
| C32 plcBasePortAttenuation | 1.3.6.1.4.1.22764.1.1.2.2.2.1.4 | Counter32 | read-only | Link attenuation (dB). |
| plcChannelModulationStringTable | 1.3.6.1.4.1.22764.1.1.2.2.3 | not-accessible | This table contains string values for a quick access to the modulation amplitude configurations of all active channels. | |
| plcChannelModulationStringEntry | 1.3.6.1.4.1.22764.1.1.2.2.3.1 | not-accessible | This row contains string values for a quick access to the modulation amplitude configuration of each active channel of the remote connection referenced by plcBasePortIndex. | |
| OCT plcRxChannelModulation | 1.3.6.1.4.1.22764.1.1.2.2.3.1.1 | OCTET STRING | read-only | The modulation amplitude values for the Rx channel of a given remote connection entry. The expected format is VALUE VALUE VALUE ... VALUE. Each value is an octet representing two modulation values. Each modulation is coded on 4 bits. There are ( 16 groups * 7 bands ) / 2 = 66 values. |
| OCT plcRxLastChannelModulation | 1.3.6.1.4.1.22764.1.1.2.2.3.1.2 | OCTET STRING | read-only | The modulation amplitude values for the Rx Last channel of a given remote connection entry. The expected format is VALUE VALUE VALUE ... VALUE. Each value is an octet representing two modulation values. Each modulation is coded on 4 bits representing ModulationValue - 1. There are ( 16 groups * 7 bands ) / 2 = 66 values. |
| OCT plcTxChannelModulation | 1.3.6.1.4.1.22764.1.1.2.2.3.1.3 | OCTET STRING | read-only | The modulation amplitude values for the Tx channel of a given remote connection entry. The expected format is VALUE VALUE VALUE ... VALUE. Each value is an octet representing two modulation values. Each modulation is coded on 4 bits. There are ( 16 groups * 7 bands ) / 2 = 66 values. |
| plcChannelModulationTable | 1.3.6.1.4.1.22764.1.1.2.2.4 | not-accessible | This table contains the modulation amplitude configuration of all active channels. | |
| plcChannelModulationEntry | 1.3.6.1.4.1.22764.1.1.2.2.4.1 | not-accessible | This row contains modulation amplitude configuration of the channel, referenced by the plcPortChannelIndex, of the remote connection referenced by plcBasePortIndex. | |
| BAN plcModBandIndex | 1.3.6.1.4.1.22764.1.1.2.2.4.1.1 | BandValue | not-accessible | The band number of which the modulations are defined |
| MOD plcModGroup1 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.2 | ModulationValue | read-only | The modulation amplitude of the first group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup2 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.3 | ModulationValue | read-only | The modulation amplitude of the second group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup3 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.4 | ModulationValue | read-only | The modulation amplitude of the third group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup4 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.5 | ModulationValue | read-only | The modulation amplitude of the fourth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup5 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.6 | ModulationValue | read-only | The modulation amplitude of the fifth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup6 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.7 | ModulationValue | read-only | The modulation amplitude of the sixth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup7 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.8 | ModulationValue | read-only | The modulation amplitude of the seventh group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup8 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.9 | ModulationValue | read-only | The modulation amplitude of the eighth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup9 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.10 | ModulationValue | read-only | The modulation amplitude of the nineth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup10 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.11 | ModulationValue | read-only | The modulation amplitude of the tenth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup11 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.12 | ModulationValue | read-only | The modulation amplitude of the eleventh group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup12 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.13 | ModulationValue | read-only | The modulation amplitude of the twelveth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup13 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.14 | ModulationValue | read-only | The modulation amplitude of the thirteenth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup14 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.15 | ModulationValue | read-only | The modulation amplitude of the fourteenth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup15 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.16 | ModulationValue | read-only | The modulation amplitude of the fifteenth group of the band entry of the channel entry for a given remote connection entry. |
| MOD plcModGroup16 | 1.3.6.1.4.1.22764.1.1.2.2.4.1.17 | ModulationValue | read-only | The modulation amplitude of the sixteenth group of the band entry of the channel entry for a given remote connection entry. |
| plcChannelModulationInput | 1.3.6.1.4.1.22764.1.1.2.2.5 | |||
| MAC plcModulationInputAddr | 1.3.6.1.4.1.22764.1.1.2.2.5.1 | MacAddress | read-write | The MAC address of the MAC layer above the plc interface of the remote PLC equipment for which the modulation value changes are requested. |
| PLC plcModulationInputChannel | 1.3.6.1.4.1.22764.1.1.2.2.5.2 | PlcChannelType | read-write | The channel type of the remote PLC equipment for which the modulation value changes are requested. |
| BAN plcModulationInputBand | 1.3.6.1.4.1.22764.1.1.2.2.5.3 | BandValue | read-write | The band number of which the modulation value changes are requested. |
| MOD plcInputModulationGroup1 | 1.3.6.1.4.1.22764.1.1.2.2.5.4 | ModulationValue | read-write | The new requested modulation amplitude of the first group of the considered band and channel input values. |
| MOD plcInputModulationGroup2 | 1.3.6.1.4.1.22764.1.1.2.2.5.5 | ModulationValue | read-write | The new requested modulation amplitude of the second group of the considered band and channel input values. |
| MOD plcInputModulationGroup3 | 1.3.6.1.4.1.22764.1.1.2.2.5.6 | ModulationValue | read-write | The new requested modulation amplitude of the third group of the considered band and channel input values. |
| MOD plcInputModulationGroup4 | 1.3.6.1.4.1.22764.1.1.2.2.5.7 | ModulationValue | read-write | The new requested modulation amplitude of the fourth group of the considered band and channel input values. |
| MOD plcInputModulationGroup5 | 1.3.6.1.4.1.22764.1.1.2.2.5.8 | ModulationValue | read-write | The new requested modulation amplitude of the fifth group of the considered band and channel input values. |
| MOD plcInputModulationGroup6 | 1.3.6.1.4.1.22764.1.1.2.2.5.9 | ModulationValue | read-write | The new requested modulation amplitude of the sixth group of the considered band and channel input values. |
| MOD plcInputModulationGroup7 | 1.3.6.1.4.1.22764.1.1.2.2.5.10 | ModulationValue | read-write | The new requested modulation amplitude of the seventh group of the considered band and channel input values. |
| MOD plcInputModulationGroup8 | 1.3.6.1.4.1.22764.1.1.2.2.5.11 | ModulationValue | read-write | The new requested modulation amplitude of the eighth group of the considered band and channel input values. |
| MOD plcInputModulationGroup9 | 1.3.6.1.4.1.22764.1.1.2.2.5.12 | ModulationValue | read-write | The new requested modulation amplitude of the nineth group of the considered band and channel input values. |
| MOD plcInputModulationGroup10 | 1.3.6.1.4.1.22764.1.1.2.2.5.13 | ModulationValue | read-write | The new requested modulation amplitude of the tenth group of the considered band and channel input values. |
| MOD plcInputModulationGroup11 | 1.3.6.1.4.1.22764.1.1.2.2.5.14 | ModulationValue | read-write | The new requested modulation amplitude of the eleventh group of the considered band and channel input values. |
| MOD plcInputModulationGroup12 | 1.3.6.1.4.1.22764.1.1.2.2.5.15 | ModulationValue | read-write | The new requested modulation amplitude of the twelveth group of the considered band and channel input values. |
| MOD plcInputModulationGroup13 | 1.3.6.1.4.1.22764.1.1.2.2.5.16 | ModulationValue | read-write | The new requested modulation amplitude of the thirteenth group of the considered band and channel input values. |
| MOD plcInputModulationGroup14 | 1.3.6.1.4.1.22764.1.1.2.2.5.17 | ModulationValue | read-write | The new requested modulation amplitude of the fourteenth group of the considered band and channel input values. |
| MOD plcInputModulationGroup15 | 1.3.6.1.4.1.22764.1.1.2.2.5.18 | ModulationValue | read-write | The new requested modulation amplitude of the fifteenth group of the considered band and channel input values. |
| MOD plcInputModulationGroup16 | 1.3.6.1.4.1.22764.1.1.2.2.5.19 | ModulationValue | read-write | The new requested modulation amplitude of the sixteenth group of the considered band and channel input values. |
| T/F plcModulationInputProceed | 1.3.6.1.4.1.22764.1.1.2.2.5.20 | TruthValue | read-write | True to request a modification of all the modulations associated to a band and a channel of a remote PLC equipment. |
| RES plcModulationInputResult | 1.3.6.1.4.1.22764.1.1.2.2.5.21 | ResultValue | read-only | Result value of the requested modulation value changes. |
| plcPortChannelTable | 1.3.6.1.4.1.22764.1.1.2.2.6 | not-accessible | This table contains the list of plc channels | |
| plcPortChannelEntry | 1.3.6.1.4.1.22764.1.1.2.2.6.1 | not-accessible | This row contains plc channel information | |
| U32 plcPortChannelIndex | 1.3.6.1.4.1.22764.1.1.2.2.6.1.1 | Unsigned32 | not-accessible | The channel number belongs to the remote connection with plc equipment associated with the plcBasePortIndex value. Only three channels are expected. Index 1 for RX channel Index 2 for RXLast channel index 3 for TX channel |
| PLC plcPortChannelType | 1.3.6.1.4.1.22764.1.1.2.2.6.1.2 | PlcChannelType | read-only | The channel type. |
| I32 plcPortChannelGain | 1.3.6.1.4.1.22764.1.1.2.2.6.1.3 | Integer32 | read-write | The gain associated with the channel. |
| CHA plcPortChannelBandwidth | 1.3.6.1.4.1.22764.1.1.2.2.6.1.4 | ChannelBandwidthValue | read-only | The bandwidth of the channel in Kbit/s. |
| CHA plcPortChannelMaxBandwidth | 1.3.6.1.4.1.22764.1.1.2.2.6.1.5 | ChannelBandwidthValue | read-only | The maximum bandwidth of the channel in Kbit/s. |
| BAN plcPortChannelSynchronizationBand | 1.3.6.1.4.1.22764.1.1.2.2.6.1.6 | BandValue | read-only | The synchronization band used for this channel. |
| plcChannelPilotStringTable | 1.3.6.1.4.1.22764.1.1.2.2.7 | not-accessible | This table contains the string values representing of pilot values of all active channels. | |
| plcChannelPilotStringEntry | 1.3.6.1.4.1.22764.1.1.2.2.7.1 | not-accessible | This row contains a quick access for pilot values , of the remote connection referenced by plcBasePortIndex. | |
| OCT plcRxChannelPilots | 1.3.6.1.4.1.22764.1.1.2.2.7.1.1 | OCTET STRING | read-only | The carrier wave numbers which support the pilot waves for the Rx Channel. The expected format is VALUE VALUE VALUE ... VALUE. Each value is a pair of octets representing the pilot values. There is one pair (pilot1 pilot2) for each of the 7 bands. |
| OCT plcRxLastChannelPilots | 1.3.6.1.4.1.22764.1.1.2.2.7.1.2 | OCTET STRING | read-only | The carrier wave numbers which support the pilot waves for the Rx Last Channel. The expected format is VALUE VALUE VALUE ... VALUE. Each value is a pair of octets representing the pilot values. There is one pair (pilot1 pilot2) for each of the 7 bands. |
| OCT plcTxChannelPilots | 1.3.6.1.4.1.22764.1.1.2.2.7.1.3 | OCTET STRING | read-only | The carrier wave numbers which support the pilot waves for the Tx Channel. The expected format is VALUE VALUE VALUE ... VALUE. Each value is a pair of octets representing the pilot values. There is one pair (pilot1 pilot2) for each of the 7 bands. |
| plcChannelPilotsTable | 1.3.6.1.4.1.22764.1.1.2.2.8 | not-accessible | This tabel contains pilots configuration for each plc channel. | |
| plcChannelPilotsEntry | 1.3.6.1.4.1.22764.1.1.2.2.8.1 | not-accessible | This row contains the pilots 1 and 2 configuration for a channel defined by the couple (plcBasePortIndex, plcPortChannelIndex) | |
| BAN plcChannelPilotBandIndex | 1.3.6.1.4.1.22764.1.1.2.2.8.1.1 | BandValue | not-accessible | The band number on which the pilots are defined. |
| PIL plcChannelPilot1 | 1.3.6.1.4.1.22764.1.1.2.2.8.1.2 | PilotValue | read-only | The carrier wave number which supports the first pilot wave for the channel associated with this entry. |
| PIL plcChannePilot2 | 1.3.6.1.4.1.22764.1.1.2.2.8.1.3 | PilotValue | read-only | The carrier wave number which supports the second pilot wave for the channel associated with this entry. |
| plcChannelPilotsInput | 1.3.6.1.4.1.22764.1.1.2.2.9 | |||
| MAC plcPilotsInputAddr | 1.3.6.1.4.1.22764.1.1.2.2.9.1 | MacAddress | read-write | The MAC address of the MAC layer above the plc interface of the remote PLC equipment for which the pilot value changes are requested. |
| PLC plcPilotsInputChannel | 1.3.6.1.4.1.22764.1.1.2.2.9.2 | PlcChannelType | read-write | The channel type of the remote PLC equipment for which the pilot value changes are requested. |
| BAN plcPilotsInputBand | 1.3.6.1.4.1.22764.1.1.2.2.9.3 | BandValue | read-write | The band number of which the pilots value changes are requested. |
| PIL plcInputChannelPilot1 | 1.3.6.1.4.1.22764.1.1.2.2.9.4 | PilotValue | read-write | The carrier wave number which supports the first pilot wave for the considered band and channel input values. |
| PIL plcInputChannelPilot2 | 1.3.6.1.4.1.22764.1.1.2.2.9.5 | PilotValue | read-write | The carrier wave number which supports the second pilot wave for the considered band and channel input values. |
| T/F plcPilotsInputProceed | 1.3.6.1.4.1.22764.1.1.2.2.9.6 | TruthValue | read-write | True to request a modification of the first and second pilot associated to a band and a channel of a remote PLC equipment. |
| RES plcPilotsInputResult | 1.3.6.1.4.1.22764.1.1.2.2.9.7 | ResultValue | read-only | Result value of the requested pilot values changes. |
| plcNodeConfiguration | 1.3.6.1.4.1.22764.1.1.2.3 | |||
| OCT plcNodeNotches | 1.3.6.1.4.1.22764.1.1.2.3.1 | OCTET STRING | read-only | The values of the notches for all the node bands. The expected format is VALUE VALUE VALUE ... VALUE. Each value is an octet representing the 8 notches of each group. There is one value for each 7 * 16 bands. |
| plcNodeNotchesTable | 1.3.6.1.4.1.22764.1.1.2.3.2 | not-accessible | This table contains Notches configuration for the SPC200 chip. | |
| plcNodeNotchesEntry | 1.3.6.1.4.1.22764.1.1.2.3.2.1 | not-accessible | This row contains Notches configuration for a group. The group is defined by the couple (plcNodeNotchesGroupIndex, plcNodeNotchesBandIndex). | |
| BAN plcNodeNotchesBandIndex | 1.3.6.1.4.1.22764.1.1.2.3.2.1.1 | BandValue | not-accessible | The band number on which the notches are defined. |
| GRO plcNodeNotchesGroupIndex | 1.3.6.1.4.1.22764.1.1.2.3.2.1.2 | GroupValue | not-accessible | The group number on which the notches are defined. |
| T/F plcNodeNotchesCarrier1 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.3 | TruthValue | read-only | Tell if the first carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier2 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.4 | TruthValue | read-only | Tell if the second carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier3 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.5 | TruthValue | read-only | Tell if the third carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier4 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.6 | TruthValue | read-only | Tell if the fourth carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier5 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.7 | TruthValue | read-only | Tell if the fifth carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier6 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.8 | TruthValue | read-only | Tell if the sixth carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier7 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.9 | TruthValue | read-only | Tell if the seventh carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesCarrier8 | 1.3.6.1.4.1.22764.1.1.2.3.2.1.10 | TruthValue | read-only | Tell if the eighth carrier of the group entry of the band entry is a notch carrier. The true value means the current carrier is a notch. |
| plcNodeNotchesInput | 1.3.6.1.4.1.22764.1.1.2.3.3 | |||
| BAN plcNodeNotchesInputBand | 1.3.6.1.4.1.22764.1.1.2.3.3.1 | BandValue | read-write | The band number on which the notches value changes are requested. |
| GRO plcNodeNotchesInputGroup | 1.3.6.1.4.1.22764.1.1.2.3.3.2 | GroupValue | read-write | The group number on which the notches value changes are requested. |
| T/F plcNodeNotchesInputCarrier1 | 1.3.6.1.4.1.22764.1.1.2.3.3.3 | TruthValue | read-write | The first carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier2 | 1.3.6.1.4.1.22764.1.1.2.3.3.4 | TruthValue | read-write | The second carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier3 | 1.3.6.1.4.1.22764.1.1.2.3.3.5 | TruthValue | read-write | The third carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier4 | 1.3.6.1.4.1.22764.1.1.2.3.3.6 | TruthValue | read-write | The fourth carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier5 | 1.3.6.1.4.1.22764.1.1.2.3.3.7 | TruthValue | read-write | The eighth carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier6 | 1.3.6.1.4.1.22764.1.1.2.3.3.8 | TruthValue | read-write | The eighth carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier7 | 1.3.6.1.4.1.22764.1.1.2.3.3.9 | TruthValue | read-write | The seventh carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputCarrier8 | 1.3.6.1.4.1.22764.1.1.2.3.3.10 | TruthValue | read-write | The eighth carrier of the considered group and band is a notch carrier. The true value means the current carrier is a notch. |
| T/F plcNodeNotchesInputProceed | 1.3.6.1.4.1.22764.1.1.2.3.3.11 | TruthValue | read-write | True to request a modification of the carrier notches associated to the considered group and band. |
| RES plcNodeNotchesInputResult | 1.3.6.1.4.1.22764.1.1.2.3.3.12 | ResultValue | read-only | Result value of the requested node carrier notches value changes. |
| OCT plcNodePilots | 1.3.6.1.4.1.22764.1.1.2.3.4 | OCTET STRING | read-only | The values of the pilot for all the node bands. The expected format is VALUE VALUE VALUE ... VALUE. Each value is a pair of octets representing the pilot values. There is one pair (pilot1 pilot2) for each of the 7 bands. |
| plcNodePilotsTable | 1.3.6.1.4.1.22764.1.1.2.3.5 | not-accessible | This table contains pilot values used by default on all channels. | |
| plcNodePilotsEntry | 1.3.6.1.4.1.22764.1.1.2.3.5.1 | not-accessible | This row contains pilot values used by default on a band. The band is defined by the index plcNodePilotsBandIndex. | |
| BAN plcNodePilotsBandIndex | 1.3.6.1.4.1.22764.1.1.2.3.5.1.1 | BandValue | not-accessible | The band number on which the pilot values are defined. |
| PIL plcNodePilot1 | 1.3.6.1.4.1.22764.1.1.2.3.5.1.2 | PilotValue | read-only | The default carrier wave number which supports the first pilot wave. |
| PIL plcNodePilot2 | 1.3.6.1.4.1.22764.1.1.2.3.5.1.3 | PilotValue | read-only | The default carrier wave number which supports the second pilot wave. |
| plcNodePilotsInput | 1.3.6.1.4.1.22764.1.1.2.3.6 | |||
| BAN plcNodePilotsInputBand | 1.3.6.1.4.1.22764.1.1.2.3.6.1 | BandValue | read-write | The band number on which the pilot values changes are requested. |
| PIL plcInputNodePilot1 | 1.3.6.1.4.1.22764.1.1.2.3.6.2 | PilotValue | read-write | The default carrier wave number which supports the first pilot wave of the considered band. |
| PIL plcInputNodePilot2 | 1.3.6.1.4.1.22764.1.1.2.3.6.3 | PilotValue | read-write | The default carrier wave number which supports the second pilot wave of the considered band. |
| T/F plcNodePilotsInputProceed | 1.3.6.1.4.1.22764.1.1.2.3.6.4 | TruthValue | read-write | True to request a modification of the pilot values associated to the considered band. |
| RES plcNodePilotsInputResult | 1.3.6.1.4.1.22764.1.1.2.3.6.5 | ResultValue | read-only | Result value of the requested node pilot values changes. |
| plcNodeAdaptsStringTable | 1.3.6.1.4.1.22764.1.1.2.3.7 | not-accessible | This table contains string values for a quick access to the adapt configurations of all the carriers. | |
| plcNodeAdaptsStringEntry | 1.3.6.1.4.1.22764.1.1.2.3.7.1 | not-accessible | This row contains string values for a quick access to the adapt configuration of each carrier of a band. | |
| BAN plcNodeAdaptsStringBandIndex | 1.3.6.1.4.1.22764.1.1.2.3.7.1.1 | BandValue | not-accessible | The band number on which the adapt values are defined. |
| OCT plcNodeAdaptsStringBand | 1.3.6.1.4.1.22764.1.1.2.3.7.1.2 | OCTET STRING | read-only | The adapt values of the 128 carriers of a band. The expected format is VALUE VALUE VALUE ... VALUE. Each value is two octets representing one adapt carrier level. There are ( 16 groups * 8 carriers) = 128 values. |
| plcNodeAdaptsTable | 1.3.6.1.4.1.22764.1.1.2.3.8 | not-accessible | This table contains adapt level configuration for each carrier of the node. | |
| plcNodeAdaptsEntry | 1.3.6.1.4.1.22764.1.1.2.3.8.1 | not-accessible | This row contains adapt level values for a group of carriers. The group is defined by the couple (plcNodeAdaptsBandIndex,plcNodeAdaptsGroupIndex). | |
| BAN plcNodeAdaptsBandIndex | 1.3.6.1.4.1.22764.1.1.2.3.8.1.1 | BandValue | not-accessible | The band number on which the adapt values are defined. |
| GRO plcNodeAdaptsGroupIndex | 1.3.6.1.4.1.22764.1.1.2.3.8.1.2 | GroupValue | not-accessible | The group number on which the adapt values are defined. |
| ADA plcNodeAdaptsCarrier1 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.3 | AdaptValue | read-only | The adapt level of the first carrier of the group. |
| ADA plcNodeAdaptsCarrier2 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.4 | AdaptValue | read-only | The adapt level of the second carrier of the group. |
| ADA plcNodeAdaptsCarrier3 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.5 | AdaptValue | read-only | The adapt level of the third carrier of the group. |
| ADA plcNodeAdaptsCarrier4 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.6 | AdaptValue | read-only | The adapt level of the fourth carrier of the group. |
| ADA plcNodeAdaptsCarrier5 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.7 | AdaptValue | read-only | The adapt level of the fifth carrier of the group. |
| ADA plcNodeAdaptsCarrier6 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.8 | AdaptValue | read-only | The adapt level of the sixth carrier of the group. |
| ADA plcNodeAdaptsCarrier7 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.9 | AdaptValue | read-only | The adapt level of the seventh carrier of the group. |
| ADA plcNodeAdaptsCarrier8 | 1.3.6.1.4.1.22764.1.1.2.3.8.1.10 | AdaptValue | read-only | The adapt level of the eighth carrier of the group. |
| plcNodeAdaptsInput | 1.3.6.1.4.1.22764.1.1.2.3.9 | |||
| BAN plcNodeAdaptsInputBand | 1.3.6.1.4.1.22764.1.1.2.3.9.1 | BandValue | read-write | The band number on which the adapt level value changes are requested. |
| GRO plcNodeAdaptsInputGroup | 1.3.6.1.4.1.22764.1.1.2.3.9.2 | GroupValue | read-write | The group number on which the adapt level value changes are requested. |
| ADA plcNodeAdaptsInputCarrier1 | 1.3.6.1.4.1.22764.1.1.2.3.9.3 | AdaptValue | read-write | The adapt level of the first carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier2 | 1.3.6.1.4.1.22764.1.1.2.3.9.4 | AdaptValue | read-write | The adapt level of the second carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier3 | 1.3.6.1.4.1.22764.1.1.2.3.9.5 | AdaptValue | read-write | The adapt level of the third carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier4 | 1.3.6.1.4.1.22764.1.1.2.3.9.6 | AdaptValue | read-write | The adapt level of the fourth carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier5 | 1.3.6.1.4.1.22764.1.1.2.3.9.7 | AdaptValue | read-write | The adapt level of the fifth carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier6 | 1.3.6.1.4.1.22764.1.1.2.3.9.8 | AdaptValue | read-write | The adapt level of the sixth carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier7 | 1.3.6.1.4.1.22764.1.1.2.3.9.9 | AdaptValue | read-write | The adapt level of the seventh carrier of the considered group of the chosen band. |
| ADA plcNodeAdaptsInputCarrier8 | 1.3.6.1.4.1.22764.1.1.2.3.9.10 | AdaptValue | read-write | The adapt level of the eighth carrier of the considered group of the chosen band. |
| T/F plcNodeAdaptsInputProceed | 1.3.6.1.4.1.22764.1.1.2.3.9.11 | TruthValue | read-write | True to request a modification of the carrier adapt level associated to the considered group and band. |
| RES plcNodeAdaptsInputResult | 1.3.6.1.4.1.22764.1.1.2.3.9.12 | ResultValue | read-only | Result value of the requested node adapt level value changes. |
| plcNodeNetConfigTable | 1.3.6.1.4.1.22764.1.1.2.3.10 | not-accessible | This table contains ip and mac addresses of the node. | |
| plcNodeNetConfigEntry | 1.3.6.1.4.1.22764.1.1.2.3.10.1 | not-accessible | This row contains ip and mac address used by an interface. | |
| IP plcNodeIpAddr | 1.3.6.1.4.1.22764.1.1.2.3.10.1.1 | IpAddress | read-write | The IP address of the IP layer above the interface. |
| IP plcNodeNetMask | 1.3.6.1.4.1.22764.1.1.2.3.10.1.2 | IpAddress | read-write | The IP Subnet mask of the IP layer above the interface. |
| MAC plcNodeMacAddr | 1.3.6.1.4.1.22764.1.1.2.3.10.1.3 | MacAddress | read-write | The MAC address of the MAC layer above the interface. |
| IP plcNodeGateway | 1.3.6.1.4.1.22764.1.1.2.3.10.1.4 | IpAddress | read-write | The Gateway address of the IP layer above the interface. |
| plcNodeActions | 1.3.6.1.4.1.22764.1.1.2.3.11 | |||
| plcNodeActionsCommit | 1.3.6.1.4.1.22764.1.1.2.3.11.1 | |||
| T/F plcNodeActionsCommitProceed | 1.3.6.1.4.1.22764.1.1.2.3.11.1.1 | TruthValue | read-write | True to request the commit of the configuration changes into the flash memory |
| RES plcNodeActionsCommitResult | 1.3.6.1.4.1.22764.1.1.2.3.11.1.2 | ResultValue | read-only | Result value of the requested flash commit operation. |
| plcNodeActionsReset | 1.3.6.1.4.1.22764.1.1.2.3.11.2 | |||
| T/F plcNodeActionsResetProceed | 1.3.6.1.4.1.22764.1.1.2.3.11.2.1 | TruthValue | read-write | True to request the reset of the node. This operation will terminate the communication between the manager and the node |
| plcNodeActionsCarrier | 1.3.6.1.4.1.22764.1.1.2.3.11.3 | |||
| T/F plcNodeActionsCarrierFlatProceed | 1.3.6.1.4.1.22764.1.1.2.3.11.3.1 | TruthValue | read-write | True to request the equipment to flat the signal |
| plcSNAnalyser | 1.3.6.1.4.1.22764.1.1.2.4 | |||
| INT plcSNAnalyserEnable | 1.3.6.1.4.1.22764.1.1.2.4.1 | INTEGER | read-write | true if the modem should turn to spectrum analyser mode. In this mode the modem enters a receive only mode, and captures periodic samples of the signal on the powerline. The spectrum analyser mode shall be disabled for normal powerline modem operation. |
| plcSNAnalyserTable | 1.3.6.1.4.1.22764.1.1.2.4.2 | not-accessible | This table gathers all statistic data specific to SPC200 chip relative to plc analyser. | |
| plcSNAnalyserEntry | 1.3.6.1.4.1.22764.1.1.2.4.2.1 | not-accessible | This row contains statistic data specific to SPC200 chip relative to a band. | |
| OCT plcSNAnalyserMinSignal | 1.3.6.1.4.1.22764.1.1.2.4.2.1.1 | OCTET STRING | read-only | Minimum signal measured over several samples for the associated carrier wave entry. The value is expressed in Glomer� which can be converted in dBm/Hz using the following formula: dBm/Hz = 19*log10(Glomer�) - 113 |
| OCT plcSNAnalyserMaxSignal | 1.3.6.1.4.1.22764.1.1.2.4.2.1.2 | OCTET STRING | read-only | Maximum signal measured on several samples for the associated carrier wave entry. The value is expressed in Glomer� which can be converted in dBm/Hz using the following formula: dBm/Hz = 19*log10(Glomer�) - 113 |
| OCT plcSNAnalyserAvgSignal | 1.3.6.1.4.1.22764.1.1.2.4.2.1.3 | OCTET STRING | read-only | Average signal measured on several samples for the associated carrier wave entry. The value is expressed in Glomer� which can be converted in dBm/Hz using the following formula: dBm/Hz = 19*log10(Glomer�) - 113 |
| OCT plcSNAnalyserLastSignal | 1.3.6.1.4.1.22764.1.1.2.4.2.1.4 | OCTET STRING | read-only | Signal measured for last sample on the associated carrier wave entry. The value is expressed in Glomer� which can be converted in dBm/Hz using the following formula: dBm/Hz = 19*log10(Glomer�) - 113 |
| C32 plcSNAnalyserFFTDiv | 1.3.6.1.4.1.22764.1.1.2.4.2.1.5 | Counter32 | read-only | FFT division factor on the associated band. |
| I32 plcSNAnalyserAGC | 1.3.6.1.4.1.22764.1.1.2.4.3 | Integer32 | read-only | Gain factor in dB, as used by the Automatic Gain Control last sample |
| plcAGCAnalyser | 1.3.6.1.4.1.22764.1.1.2.5 | |||
| INT plcAGCAnalyserEnable | 1.3.6.1.4.1.22764.1.1.2.5.1 | INTEGER | read-write | |
| OCT plcAGCAnalyserSamplesPart1 | 1.3.6.1.4.1.22764.1.1.2.5.2 | OCTET STRING | read-only | |
| OCT plcAGCAnalyserSamplesPart2 | 1.3.6.1.4.1.22764.1.1.2.5.3 | OCTET STRING | read-only | |
| plcBssId | 1.3.6.1.4.1.22764.1.1.2.6 | |||
| INT plcMasterBssId | 1.3.6.1.4.1.22764.1.1.2.6.1 | INTEGER | read-write | The value of the master Bss Id |
| INT plcSlaveBssId | 1.3.6.1.4.1.22764.1.1.2.6.2 | INTEGER | read-write | The value of the slave Bss Id |
| plcSpy | 1.3.6.1.4.1.22764.1.1.2.7 | |||
| T/F plcSpyIsDynamic | 1.3.6.1.4.1.22764.1.1.2.7.1 | TruthValue | read-write | True to set the spy dynamic mode |
| BAN plcStaticSpySynchBandNb | 1.3.6.1.4.1.22764.1.1.2.7.2 | BandValue | read-write | The synchronization band number used for static spy mode |
| softwareMgnt | 1.3.6.1.4.1.22764.1.1.3 | |||
| STR currentSoftwareVersion | 1.3.6.1.4.1.22764.1.1.3.1 | DisplayString | read-only | The name of the current software release. |
| STR currentSoftwareBoardVersion | 1.3.6.1.4.1.22764.1.1.3.2 | DisplayString | read-only | The name of the current software board release. |
| STR currentSoftwareAFEVersion | 1.3.6.1.4.1.22764.1.1.3.3 | DisplayString | read-only | The name of the current software Analog Front End release. |
| softwareTable | 1.3.6.1.4.1.22764.1.1.3.4 | not-accessible | This table contains the current and reserve softwares of the node. | |
| softwareEntry | 1.3.6.1.4.1.22764.1.1.3.4.1 | not-accessible | This row contains software information. | |
| SOF softwareIndex | 1.3.6.1.4.1.22764.1.1.3.4.1.1 | SoftwareIndex | not-accessible | The index number of the software. |
| STR softwareVersion | 1.3.6.1.4.1.22764.1.1.3.4.1.2 | DisplayString | read-only | The name of the software release. |
| softwareUpload | 1.3.6.1.4.1.22764.1.1.3.5 | |||
| IP softwareUploadTFTPServerIP | 1.3.6.1.4.1.22764.1.1.3.5.1 | IpAddress | read-write | The IP address of the TFTP serveur |
| STR softwareUploadLogin | 1.3.6.1.4.1.22764.1.1.3.5.2 | DisplayString | read-write | The user login on the TFTP server |
| STR softwareUploadPassword | 1.3.6.1.4.1.22764.1.1.3.5.3 | DisplayString | read-write | The user password on the TFTP server. Warning: This field is displayed using 6 * characters |
| STR softwareUploadFileName | 1.3.6.1.4.1.22764.1.1.3.5.4 | DisplayString | read-write | The software file name to upload |
| T/F softwareUploadProceed | 1.3.6.1.4.1.22764.1.1.3.5.5 | TruthValue | read-write | True to request the uploading to start |
| SOF softwareUploadResult | 1.3.6.1.4.1.22764.1.1.3.5.6 | SoftwareActionResultValue | read-only | Result value of the requested uploading |
| I32 softwareUploadTFTPServerPort | 1.3.6.1.4.1.22764.1.1.3.5.7 | Integer32 | read-write | The service port of the TFTP server |
| softwareAction | 1.3.6.1.4.1.22764.1.1.3.6 | |||
| SOF softwareActionIndex | 1.3.6.1.4.1.22764.1.1.3.6.1 | SoftwareIndex | read-write | The index of the reserve software |
| SOF softwareActionType | 1.3.6.1.4.1.22764.1.1.3.6.2 | SoftwareActionType | read-write | Type of the software action software: switch, remove |
| T/F softwareActionProceed | 1.3.6.1.4.1.22764.1.1.3.6.3 | TruthValue | read-write | True to request the switch between the current and the reserver software to start |
| SOF softwareActionResult | 1.3.6.1.4.1.22764.1.1.3.6.4 | SoftwareActionResultValue | read-only | Result value of the requested action |
| plcConformance | 1.3.6.1.4.1.22764.1.1.4 | |||
| plcCompliances | 1.3.6.1.4.1.22764.1.1.4.1 | |||
| plcCompliance | 1.3.6.1.4.1.22764.1.1.4.1.1 | The compliance statement for SPC200 chip. | ||
| plcGroups | 1.3.6.1.4.1.22764.1.1.4.2 | |||
| nodeGroup | 1.3.6.1.4.1.22764.1.1.4.2.1 | A collection of objects providing node configuration information. | ||
| inputNodeGroup | 1.3.6.1.4.1.22764.1.1.4.2.2 | A collection of objects used to request node configuration information changes. | ||
| topologyGroup | 1.3.6.1.4.1.22764.1.1.4.2.3 | A collection of objects providing topology configuration. | ||
| inputTopologyGroup | 1.3.6.1.4.1.22764.1.1.4.2.4 | A collection of objects used to request topology configuration changes. | ||
| statisticGroup | 1.3.6.1.4.1.22764.1.1.4.2.5 | A collection of objects providing statistic data on node and plc link performances. | ||
| softwareGroup | 1.3.6.1.4.1.22764.1.1.4.2.6 | A collection of objects providing software management | ||
| analyserGroup | 1.3.6.1.4.1.22764.1.1.4.2.7 | A collection of objects providing spectrum analyser data | ||
| agentCapabilities | 1.3.6.1.4.1.22764.1.1.4.3 | The SPC200 chip SNMP agent capabilities | ||
| ipExt | 1.3.6.1.4.1.22764.1.4 | Extended ip needed for SPiDCOM functionalities | ||
| T/F ipDynamic | 1.3.6.1.4.1.22764.1.4.1 | TruthValue | read-write | True if Ip address is set dynamically |
| ipExtGroup | 1.3.6.1.4.1.22764.1.4.2 | The fields needed by the SPiDCOM functionalities |
RFC description
Spidcom SPC200 PLC modem management MIB, managing modulation, channel configuration, and firmware upgrades.
Start monitoring powerline communication (PLC) network adapter/bridge (master/slave BSS role, sync-band/Ethernet interface status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.