SL-SFP-MIB

All MIBs › SL-SFP-MIB

Organization: Smartoptics AS

Last Updated: 2005-01-25

Description: MIB for SFP transceiver modules on SmartOptics SiteLight equipment, covering configuration, digital diagnostics, tunable wavelength control, and optical traps

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SL-SFP-MIB?

SL-SFP-MIB is a vendor MIB from SmartOptics for its SiteLight optical transport equipment, managing SFP (Small Form-factor Pluggable) transceiver modules, part of the optical networking/DWDM technology area. It exposes SFP configuration data including transceiver identifiers, connector type, and standards-compliance flags (InfiniBand, ESCON, SONET, Gigabit Ethernet, Fibre Channel), alongside separate diagnostic and trap sub-branches for digital diagnostics and tunable wavelength control. This is directly relevant to monitoring hardware status: the digital diagnostics branch (sfpDiag) would surface transceiver health metrics such as optical power, temperature, and bias current, while sfpTraps would notify on transceiver insertion/removal or out-of-range conditions, letting operators catch a failing or incompatible SFP before it causes a link outage. It likely parallels or extends the SFF-8472 digital diagnostic monitoring (DDM) industry standard for SFP transceivers rather than any single IETF MIB. It is deployed on SmartOptics SiteLight optical transport platforms used in metro/regional DWDM and passive optical networking deployments. Network engineers evaluating or troubleshooting this functionality can download the SL-SFP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SL-SFP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SmartOptics SiteLight optical transport platform
SFP transceiver module

Monitoring Examples

An operator would poll sfpConfigTable/sfpConfigEntry indexed by sfpConfigInterface to check sfpConfigXcvrId and sfpConfigConnectorCode, confirming the correct SFP type is installed, and cross-check sfpConfigSonetCompliance or sfpConfigGbeCompliance flags against the expected line rate. Combined with the sfpDiag branch for real-time optical power/temperature readings and sfpTraps for insertion/removal or threshold-crossing alerts, this would reveal a degrading transceiver (e.g., declining received optical power) before a full link failure occurs.

What Can Be Monitored

transceiver type/identifier
connector and standards compliance
optical digital diagnostics (power, temperature, bias)
wavelength tuning
SFP insertion/removal alarms

Imported Objects

From FLOAT-TC-MIB

Float128TC
Float32TC
Float64TC

From IF-MIB

InterfaceIndex

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount
PerfTotalCount

From SL-ENTITY-MIB

CleiCode

From SL-NE-MIB

sitelight

OBJECT-IDENTITY

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
slSfp	1.3.6.1.4.1.4515.1.10			This MIB module describes the SFP Modules
sfpConf	1.3.6.1.4.1.4515.1.10.1
sfpConfigTable	1.3.6.1.4.1.4515.1.10.1.1		not-accessible	The SFP configuration table. The table defines the configuration of the SFP-1310 and the SFP-WDM modules.
sfpConfigEntry	1.3.6.1.4.1.4515.1.10.1.1.1		not-accessible	An entry in the SFP configuration table. The index to this table is the same as the ifIndex of the SFP. The SFP Config Table contain and entry for each module of a type SFP.
NUM sfpConfigInterface	1.3.6.1.4.1.4515.1.10.1.1.1.1	InterfaceIndex	read-only	The Interface Index of the SFP (type=196).
INT sfpConfigXcvrId	1.3.6.1.4.1.4515.1.10.1.1.1.2	INTEGER	read-only	The identifier value specifies the physical device described by the serial information. This value shall be included in the serial data. The defined identifier values are: 00h - Unknown or unspecified 01h - GBIC 02h - Module/connector soldered to motherboard 03h - 1310 SFP 04-0Ah - Reserved for XFP and other platforms 0Bh - DWDM SFP 80-FFh - Vendor specific.
INT sfpConfig1310ExtXcvrId	1.3.6.1.4.1.4515.1.10.1.1.1.3	INTEGER	read-only	The extended identifier value provides additional information about the 1310 transceiver. The defined identifier values are: 00h GBIC definition is not specified or the GBIC definition is not compliant with a defined MOD_DEF. See product specification for details. 01h GBIC is compliant with MOD_DEF 1 02h GBIC is compliant with MOD_DEF 2 03h GBIC is compliant with MOD_DEF 3 04h GBIC/SFP function is defined by serial ID only 05h GBIC is compliant with MOD_DEF 5 06h GBIC is compliant with MOD_DEF 6 07h GBIC is compliant with MOD_DEF 7 08-FFh Reserved
INT sfpConfigWdmExtXcvrId	1.3.6.1.4.1.4515.1.10.1.1.1.4	INTEGER	read-only	This field is used to distinguish between different types of DWDM transceivers and different power and environmental classes. The defined identifier values are: Bits 7..6: Reserved Bits 5..4: Class of WDM 00: no WDM 01: CWDM 10: DWDM Bits 3..2: Class of power 00: P1.5W 11: reserved Bits 3..2: Class of temp 00: [-5, 70C] 01: [1W,1.5W] 10: reserved 11: Defined by Bytes 15 - 16.
INT sfpConfigConnectorCode	1.3.6.1.4.1.4515.1.10.1.1.1.5	INTEGER	read-only	The identifier value specifies the physical device described by the serial information. This value shall be included in the serial data. The defined identifier values are: 00h - Unknown or unspecified 01h - SC 02h - Fibre Channel Style 1 copper connector 03h - Fibre Channel Style 2 copper connector 04h - BNC/TNC 05h - Fibre Channel coaxial headers 06h - FiberJack 07h - LC 08h - MT-RJ 09h - MU 0Ah - SG 0Bh - Optical pigtail 0Ch - 1Fh - Reserved 20h - HSSDC II 21h - Copper Pigtail 22h - 7Fh - Reserved 80-FFh - Vendor specific.
INT sfpConfigInfibandCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.6	INTEGER	read-only	The following bit significant indicators define the Infiband interfaces that are supported by the transceiver. The defined identifier values are: Bits 0: 1X SX Bits 1: 1X LX Bits 2: 1X Copper Active Bits 3: 1X Copper Passive.
INT sfpConfigEsconCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.7	INTEGER	read-only	The following bit significant indicators define the ESCON interfaces that are supported by the transceiver. The defined identifier values are: Bits 0: ESCON MMF, 1310nm LED Bits 1: ESCON SMF, 1310nm Laser
INT sfpConfigSonetCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.8	INTEGER	read-only	The following bit significant indicators define the SONET interfaces that are supported by the transceiver. The defined identifier values are: Bits 0: SONET reach specifier bit 1 Bits 1: SONET reach specifier bit 2 Where: 00 speed OC-3/OC-12/OC-48 Short reach - SONET SR compliant 10 speed OC-3/OC-12/OC-48 Short reach - SONET SR-1 compliant 10 speed OC-3/OC-12/OC-48 Intermediate reach - SONET IR-1 compliant 01 speed OC-3/OC-12/OC-48 Intermediate reach - SONET IR-2 compliant 10 speed OC-3/OC-12/OC-48 Long reach - SONET LR-1 compliant 01 speed OC-3/OC-12/OC-48 Long reach - SONET LR-2 compliant 11 speed OC-3/OC-12/OC-48 Long reach - SONET LR-3 compliant Bits 2: OC-48, single mode long reach Bits 3: OC-48, single mode inter. reach Bits 4: OC-48, multi-mode short reach Bits 5: OC-12, single mode long reach Bits 6: OC-12, single mode inter. reach Bits 7: OC-12 multi-mode short reach Bits 8: OC-3, single mode long reach Bits 9: OC-3, single mode inter. reach Bits 10: OC-3, multi-mode short reach.
INT sfpConfigGbeCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.9	INTEGER	read-only	The following bit significant indicators define the Infiband interfaces that are supported by the transceiver. The defined identifier values are: Bits 0: 1000BASE-T Bits 1: 1000BASE-CX Bits 2: 1000BASE-LX Bits 3: 1000BASE-SX Bits 4: 100BASE-LX/LX10 -- 1310 Bits 5: 100BASE-FX -- 1310 Bits 6: BASE-BX10 -- 1310 Bits 7: BASE-PX.
INT sfpConfigFcCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.10	INTEGER	read-only	The following bit significant indicators define the FC interfaces that are supported by the transceiver. The defined identifier values are: - Fibre Channel link length: Bits 0: very long distance (V) Bits 1: short distance (S) Bits 2: intermediate distance (I) Bits 3: long distance (L) - Fibre Channel transmitter technology Bits 4: Longwave laser (LC) Bits 5: Electrical inter-enclosure (EL) Bits 6: Electrical intra-enclosure (EL) Bits 7: Shortwave laser w/o OFC (SN) Bits 8: Shortwave laser w/ OFC (SL) Bits 9: Longwave laser (LL) Bits 10: Copper Active -- 1310 Bits 11: Copper Passive -- 1310 - Fibre Channel transmission media Bits 12: Twin Axial Pair (TW) Bits 13: Shielded Twisted Pair (TP) Bits 14: Miniature Coax (MI) Bits 15: Video Coax (TV) Bits 16: Multi-mode, 62.5m (M6) Bits 17: Multi-mode, 50 m (M5) Bits 18: Single Mode (SM) - Fibre Channel speed Bits 19: 800 MB/Sec Bits 20: 400 MB/Sec Bits 21: 200 MB/Sec Bits 22: 100 MB/Sec Bits 23: 1200 MB/Sec Bits 24: 1600 MB/Sec.
INT sfpConfigEncodingCode	1.3.6.1.4.1.4515.1.10.1.1.1.11	INTEGER	read-only	The encoding value indicates the serial encoding mechanism that is the nominal design target of the particular transceiver. The value shall be contained in the serial data. The defined encoding values are: 00h: Unspecified 01h: 8B10B 02h: 4B5B 03h: NRZ 04h: Manchester 05h: SONET Scrambled 06h -FFh: Reserved.
INT sfpConfigNominalBitRate	1.3.6.1.4.1.4515.1.10.1.1.1.12	INTEGER	read-only	The nominal bit rate (BR, nominal) is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. The bit rate includes those bits necessary to encode and delimit the signal as well as those bits carrying data information. A value of 0 indicates that the bit rate is not specified and must be determined from the transceiver technology. The actual information transfer rate will depend on the encoding of the data, as defined by the encoding value.
INT sfpConfigLength9mKm	1.3.6.1.4.1.4515.1.10.1.1.1.13	INTEGER	read-only	Addition to EEPROM data from original GBIC definition. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber. A value of zero means that the transceiver does not support single mode fiber or that the length information must be determined from the transceiver technology.
INT sfpConfigLength9m100m	1.3.6.1.4.1.4515.1.10.1.1.1.14	INTEGER	read-only	This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber. The value is in units of 100 meters. A value of 255 means that the transceiver supports a link length greater than 25.4 km. A value of zero means that the transceiver does not support single mode fiber or that the length information must be determined from the transceiver technology.
INT sfpConfigLength50m10m	1.3.6.1.4.1.4515.1.10.1.1.1.15	INTEGER	read-only	This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multi-mode fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a link length greater than 2.54 km. A value of zero means that the transceiver does not support 50 micron multimode fiber or that the length information must be determined from the transceiver technology.
INT sfpConfigLength62m10m	1.3.6.1.4.1.4515.1.10.1.1.1.16	INTEGER	read-only	This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron multi-mode fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a link length greater than 2.54 km. A value of zero means that the transceiver does not support 50 micron multimode fiber or that the length information must be determined from the transceiver technology. It is common for the transceiver to support both 50 micron and 62.5 micron fiber.
INT sfpConfigLengthCopper1m	1.3.6.1.4.1.4515.1.10.1.1.1.17	INTEGER	read-only	This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using copper cable. The value is in units of 1 meter. A value of 255 means that the transceiver supports a link length greater than 254 meters. A value of zero means that the transceiver does not support copper cables or that the length information must be determined from the transceiver technology.
INT sfpConfigMaxTemp	1.3.6.1.4.1.4515.1.10.1.1.1.18	INTEGER	read-only	This field defines the maximum operating case temperature the module is rated for. The maximum case temperature is encoded as a signed two�s complement value in �C, yielding a total range of �128C to +127�C. This field should be used even if a standard operating temperature class is indicated in the Extended Indentifier Byte (Byte 1).
INT sfpConfigMinTemp	1.3.6.1.4.1.4515.1.10.1.1.1.19	INTEGER	read-only	This field defines the minimum operating case temperature the module is rated for. The maximum case temperature is encoded as a signed two�s complement value in �C, yielding a total range of �128C to +127�C. This field should be used even if a standard operating temperature class is indicated in the Extended Indentifier Byte.
INT sfpConfigMaxSupplyCurrent	1.3.6.1.4.1.4515.1.10.1.1.1.20	INTEGER	read-only	This field defines the maximum supply current the module will consume under worst case conditions. The maximum current is the byte value * 4mA.
INT sfpConfigChannelSpacing	1.3.6.1.4.1.4515.1.10.1.1.1.21	INTEGER	read-only	In the case of SFP: This bit field value identifies the densest channel spacing the module is compatible with and the number of channels over which the module may be tuned by user command. If not tunable, the number of channels is entered as 1. The bit fields are: Bits 7..6: Channel Spacing 00: 200 GHz (DWDM) 01: 100 GHz (DWDM) 10: 50 Ghz (DWDM) 11: Reserved Bits 5..0: Number of channels (1 � 63). In the case of XFP: The value of this field is equal to the guaranteed range of laser wavelength (+/- value) from Nominal wavelength. (Wavelength Tol. = value/200 in nm)
STR sfpConfigVendorName	1.3.6.1.4.1.4515.1.10.1.1.1.22	SnmpAdminString	read-only	The vendor name is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h). The vendor name shall be the full name of the corporation, a commonly accepted abbreviation of the name of the corporation, the SCSI company code for the corporation, or the stock exchange code for the corporation. At least one of the vendor name or the vendor OUI fields shall contain valid serial data.
INT sfpConfigOptionalWdm	1.3.6.1.4.1.4515.1.10.1.1.1.23	INTEGER	read-only	The bits in the option field shall specify the options implemented in the transceiver. The following bits are defined: Bits 7: Optional Interrupt Pin Functionality Supported (1 if supported) Bits 6..4: Pilot Tone Functionality 000b: No Pilot Tone Functionality 001b: Pilot Tone Detection Only 010b: Pilot Tone Injection Only 011b: Pilot Tone Injection and Detection 100b: Enhanched Pilot Tone Functionality 101b-111b: Reserved Bits 3: Variable Optical Attenuator Implemented (1 if implemented) Bits 2: Extended Transmit Power Monitoring 0: Default (SFF-8472) TX Power Monitoring 1: Extended TX Power Monitoring (+18.2 dBm max) Bits 1: Wavelength Monitor Type in A2 Byte 106-107 0: Monitor is Wavelength 1: Monitor is Laser Temperature Bits 0: Variable Decision Threshold (1 if implemented)
INT sfpConfigVendorOUI	1.3.6.1.4.1.4515.1.10.1.1.1.24	INTEGER	read-only	The vendor organizationally unique identifier field (vendor OUI) is a 3-byte field that contains the IEEE Company Identifier for the vendor. A value of all zero in the 3-byte field indicates that the Vendor OUI is unspecified.
STR sfpConfigVendorPN	1.3.6.1.4.1.4515.1.10.1.1.1.25	SnmpAdminString	read-only	The vendor part number (vendor PN) is a 16-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h), defining the vendor part number or product name. A value of all zero in the 16-byte field indicates that the vendor PN is unspecified.
STR sfpConfigVendorRev	1.3.6.1.4.1.4515.1.10.1.1.1.26	SnmpAdminString	read-only	The vendor revision number (vendor rev) is a 4-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h), defining the vendor�s product revision number. A value of all zero in the 4-byte field indicates that the vendor PN is unspecified.
INT sfpConfigWaveLength	1.3.6.1.4.1.4515.1.10.1.1.1.27	INTEGER	read-only	In the case of DWDM: Nominal transmitter output wavelength in units of 0.01nm. As an example, a wavelength of 1550.51nm would be encoded as: 155051. In the case of 1310: The laser wavelength is equal to the the integer value in nm with 00 at the end. As an example, a wavelength of 1310 would be encoded as: 131000.
INT sfpConfigExtendedOptions	1.3.6.1.4.1.4515.1.10.1.1.1.28	INTEGER	read-only	Specify the bitmap options implemented in the transceiver as described in. The bits definition is: 5 RATE_SELECT is implemented NOTE: Lack of implemention does not indicate lack of simultaneous compliance with multiple standard rates. Compliance with particular standards should be determined from Transceiver Code. 4 TX_DISABLE is implemented and disables the serial output. 3 TX_FAULT signal implemented. (See SFP MSA) 2 Loss of Signal implemented, signal inverted from standard definition in SFP MSA. NOTE: This is not standard SFP/GBIC behavior and should be avoided, since non-interoperable behavior results. 1 Loss of Signal implemented, signal as defined in SFP MSA.
INT sfpConfigMaxBitRate	1.3.6.1.4.1.4515.1.10.1.1.1.29	INTEGER	read-only	The upper bit rate limit at which the transceiver will still meet its specifications (BR, max) is specified in units of 1% above the nominal bit rate. A value of zero indicates that this field is not specified.
INT sfpConfigMinBitRate	1.3.6.1.4.1.4515.1.10.1.1.1.30	INTEGER	read-only	The lower bit rate limit at which the transceiver will still meet its specifications (BR, min) is specified in units of 1% below the nominal bit rate. A value of zero indicates that this field is not specified.
STR sfpConfigVendorSN	1.3.6.1.4.1.4515.1.10.1.1.1.31	SnmpAdminString	read-only	The vendor serial number (vendor SN) is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h), defining thevendor�s serial number for the transceiver. A value of all zero in the 16-byte field indicates that the vendor PN is unspecified.
STR sfpConfigDateCode	1.3.6.1.4.1.4515.1.10.1.1.1.32	SnmpAdminString	read-only	The date code is an 6-byte field that contains the vendor�s date code in ASCII characters. The date code is mandatory. The date code shall be in the format: .
INT sfpConfigDiagnosticMonitoring	1.3.6.1.4.1.4515.1.10.1.1.1.33	INTEGER	read-only	A field with 8 single bit indicators which describe the optional digital diagnostic features implemented in the transceiver. Since transceivers will not necessarily implement all optional features described in this document, the �Enhanced Options� bit field allows the host system to determine which functions are available over the 2 wire serial bus. The bits assignment is: 7 Reserved for legacy diagnostic implementations. Must be �0� for compilance with this document. 6 Digital diagnostic monitoring implemented (described in this document). Must be �1� for compliance with this document. 5 Internally Calibrated 4 Externally Calibrated 3 Received power measurement type 0 = OMA, 1 = Average Power 2 Address change required.
INT sfpConfigEnhanceOptions	1.3.6.1.4.1.4515.1.10.1.1.1.34	INTEGER	read-only	A field with 6 single bit indicators which describe the optional digital diagnostic features implemented in the transceiver. Since transceivers will not necessarily implement all optional features described in this document, the �Enhanced Options� bit field allows the host system to determine which functions are available over the 2 wire serial bus. A �1� indicates that the particular function is implemented in the transceiver.. The bits assignment is: Bits 7: Optional Alarm/warning flags implemented for all monitored quantities Bits 6: Optional Soft TX_DISABLE control and monitoring implemented Bits 5: Optional Soft TX_FAULT monitoring implemented Bits 4: Optional Soft RX_LOS monitoring implemented Bits 3: Option not enabled in DWDM. 8472- Optional Soft RATE_SELECT control and monitoring implemented Bits 2: Option not enabled in DWDM. 8472- Optional Application Select control implemented per SFF-8079
INT sfpConfig8472Compliance	1.3.6.1.4.1.4515.1.10.1.1.1.35	INTEGER	read-only	An unsigned integer that indicates which feature set(s) are implemented in the transceiver. The defined values are: 0 - Digital diagnostic functionality not included or undefined. 1 - Includes functionality described in Rev 9.3 SFF-8472. 2 - Includes functionality described in Rev 9.4 SFF-8472.
INT sfpConfigTunableWaveLength	1.3.6.1.4.1.4515.1.10.1.1.1.36	INTEGER	read-write	Wavelength Tuning Control. The availability of this function is indicated in the object sfpConfigChannelSpacing, where number of channels greater than 1 indicates tunability. The wavelength is set to the channel number written to this byte. For a value of 0, channel 1 is selected. For values greater than the maximum channel number, the maximum channel number is selected. The object value is defaults to 1 on power-up.
INT sfpConfigVoaControl	1.3.6.1.4.1.4515.1.10.1.1.1.37	INTEGER	read-write	Variable Optical Attenuator Control. Used to control the wavelength in tunable modules. The availability of this function is indicated in Bit 3 of sfpConfigOptionalWdm. The amount of attenuation set is given by the Byte value * 0.1 dB, and thus ranges from 0 to 25.6 dB. The object value defaults to 0 on power-up.
INT sfpConfigVdtControl	1.3.6.1.4.1.4515.1.10.1.1.1.38	INTEGER	read-write	Variable Decision Threshold Control. Used to control the variable decision threshold function. The availability of this function is indicated in Bit 0 of sfpConfigOptionalWdm. The object value is a 2�s complement 7 bit value (-128 - +127). The decision threshold set is given by: Decision Threshold = 50% + [VAL/256]*100% The object value defaults to 0 on power-up corresponding to 50%.
INT sfpConfigPilotToneModulation	1.3.6.1.4.1.4515.1.10.1.1.1.39	INTEGER	read-write	Pilot Tone Injection Modulation Depth. When basic MSA pilot tone injection functionality is implemented (as indicated in the Serial ID fields by bits 4-6 of of sfpConfigOptionalWdm) Tjis object may be used by the vendor to indicate modulation depth per unit control swing on pin 7. The modulation depth per control swing is given by: Modulation Depth = 0.2% * VAL / Vpp(pin7) A value of 0 indicates that the modulation depth per input swing is within the range
STR sfpConfigCleiCode	1.3.6.1.4.1.4515.1.10.1.1.1.40	DisplayString	read-only	The COMMON LANGUAGE Equipment Code. The CLEI code contains an intelligent ten-character code that identifies the telecommunications equipment. The Clei Code resides in the SEEP of the SFP.
INT sfpConfigXfpExtXcvrId	1.3.6.1.4.1.4515.1.10.1.1.1.41	INTEGER	read-only	This field is used to distinguish between different types of DWDM transceivers and different power and environmental classes. The defined identifier values are: Bits 7..6: 00: Power Level 1 Module (1.5 W max. power dissipation.) 01: Power Level 2 Module (2.5W Max) 10: Power Level 3 Module (3.5W max. power dissipation.) 11: Power Level 4 Module (>3.5W max. power dissipation.) Bit 5: CDR exist 0: Module with CDR function 1: Non-CDR version of XFP Bits 5: TX ref clock is required 0: TX Ref Clock Input Required 1: TX Ref Clock Input Not Required Bits 3: CLEI code is present 0: No CLEI code present in Table 02h 1: CLEI code present in Table 02h Bits 2..0: Resesrved
INT sfpConfigXfpEncodingCode	1.3.6.1.4.1.4515.1.10.1.1.1.42	INTEGER	read-only	The encoding value indicates the serial encoding mechanism that is the nominal design target of the particular transceiver. The value shall be contained in the serial data. The defined encoding values are: Bit 7: 64B/66B Bit 6: 8B/10B Bit 5: SONET scrambled Bit 4: NRZ Bit 3: RZ Bits 2-0: Reserved.
INT sfpConfigXfpMinBitRate	1.3.6.1.4.1.4515.1.10.1.1.1.43	INTEGER	read-only	The minimum bit rate (BR, minimum) is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. The bit rate includes those bits necessary to encode and delimit the signal as well as those bits carrying data information. A value of 0 indicates that the minimum bit rate is not specified andmust be determined from the transceiver technology. The actual information transfer rate will depend on the encoding of the data, as defined by the encoding value. Specific CDR rate support is indicated in Byte 164.
INT sfpConfigXfpMaxBitRate	1.3.6.1.4.1.4515.1.10.1.1.1.44	INTEGER	read-only	The maximum bit rate (BR, maximum) is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. The bit rate includes those bits necessary to encode and delimit the signal as well as those bits carrying data information. A value of 0 indicates that the maximum bit rate is not specified and must be determined from the transceiver technology. The actual information transfer rate will depend on the encoding of the data, as defined by the encoding value. Specific CDR rate support is indicated in Byte 164.
INT sfpConfig10GSonetCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.45	INTEGER	read-only	The following bit significant indicators define the SONET interfaces that are supported by the transceiver. The defined identifier values are: Bits 0-1: Reserved Bits 2: I-64.5 - 1550 nm, 25 km, SM, IO Bits 3: I-64.3 - 1550 nm, 25 km, SM, IO Bits 4: I-64.2 - 1550 nm, 25 km, SM, IO Bits 5: I-64.2r - 1550 nm, 2 km, SM, VSR Bits 6: I-64.1/VSR2000-2R1/P1I1-2D1 - 1310 nm, 2 km, SM, VSR Bits 7: I-64.1r/VSR600-2R1 - 1310 nm, 0.6 km, Laser-MM Fibre-SM, VSR Bits 8: Reserved Bits 9: S-64.5b - 1550 nm, 40 km, SH Bits 10: S-64.5a - 1550 nm, 40 km, SH Bits 11: S-64.3b Bits 12: S-64.3a - 1550 nm, 40 km, SM, SH Bits 13: S-64.2b - 1550 nm, 40 km, SM, SH Bits 14: S-64.2a - 1550 nm, 40 km, SM, SH Bits 15: S-64.1 - 1310 nm, 20 km, IO Bits 16-17: Reserved Bits 18: G.959.1 P1L1-2D2 - 1550 nm, SM, 80 km, LH Bits 19: L-64.3 - 1550 nm, 80 km, LH Bits 20: L-64.2c - 1550 nm, 80 km, LH Bits 21: L-64.2b - 1550 nm, 80 km, LH Bits 22: L-64.2a - 1550 nm, 80 km, LH Bits 23: L-64.1 - 1310 nm, SM, 40 km, SH Bits 24-28: Reserved Bits 29: V-64.3 - 1550 nm, SM, 120 km, VL Bits 30: V-64.2b - 1550 nm, SM, 120 km, VL Bits 31: V-64.2a - 1550 nm, SM, 120 km, VL.
INT sfpConfig10GbeCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.46	INTEGER	read-only	The following bit significant indicators define the 10GbE interfaces that are supported by the transceiver. The defined identifier values are: Bits 0: Reserved Bits 1: 10GBASE-EW - WAN, 1550 nm, SM, ER Bits 2: 10GBASE-LW - WAN, 1310 nm, SM, LR Bits 3: 10GBASE-SW - WAN, 850 nm, MM, SR Bits 4: 10GBASE-LRM (Long reach Multimode) - LAN, 1310 nm, MM, SR fiber, 0.2 km, SR Bits 5: 10GBASE-ER (extended range) - LAN, 1550 nm, SM, 40 km, ER Bits 6: 10GBASE-LR (Long Range) - LAN, 1310 nm, SM, 10 km, LR Bits 7: 10GBASE-SR - LAN, 850 nm, MM, 0.3 km, SR.
INT sfpConfig10GFcCompliance	1.3.6.1.4.1.4515.1.10.1.1.1.47	INTEGER	read-only	The following bit significant indicators define the 10GFC interfaces that are supported by the transceiver. The defined identifier values are: - Fibre Channel link length: Bits 0-3: Reserved Bits 4: Intermediate Reach 1300 nm FP - 1310 nm, SM, IR Bits 5: Extended Reach 1550 nm - 1550 nm, SM, ER Bits 6: 1200-SM-LL-L - 1310 nm, SM, LR Bits 7: 1200-MX-SN-I - 850 nm, MM, IR.
INT sfpConfigXfpDeviceTech	1.3.6.1.4.1.4515.1.10.1.1.1.48	INTEGER	read-only	The following bit significant indicators define the XFP device technology: Bits 0: 0-Transmitter not Tunable 1-Transmitter Tunable Bits 1: Detector Type: 0-PIN detector 1-APD detector Bits 2: Cooled transmitter Bits 3: Wavelength control: 0-No wavelength control 1-Active wavelength control Bits 4-7: Transmitter technology: 0000b 850 nm VCSEL 0001b 1310 nm VCSEL 0010b 1550 nm VCSEL 0011b 1310 nm FP 0100b 1310 nm DFB 0101b 1550 nm DFB 0110b 1310 nm EML 0111b 1550 nm EML 1000b Copper or others 1001b 1550 nm tunable 1111b-1001b Reserved.
INT sfpConfigXfpTuningSupported	1.3.6.1.4.1.4515.1.10.1.1.1.49	INTEGER	read-only	Indicate the XFP tuning support: Bit1: wavelenght (Tunable DWDM - selection in 50 pm steps) Bit2: frequency (Tunable DWDM - selection by channel number) For exmaple the value 0 means no support, and 3 means both.
INT sfpConfigXfpDesiredChannel	1.3.6.1.4.1.4515.1.10.1.1.1.50	INTEGER	read-write	User input of channel number, which is an integer 1 to N (N=Number of Channels).
INT sfpConfigXfpDesiredWl	1.3.6.1.4.1.4515.1.10.1.1.1.51	INTEGER	read-write	User input of Wavelength setpoint (in units of 50 picometers).
INT sfpConfigXfpWlError	1.3.6.1.4.1.4515.1.10.1.1.1.52	INTEGER	read-only	Monitor of Current Wavelength Error(in units of 5 picometers).
INT sfpConfigXfpDesiredFreq	1.3.6.1.4.1.4515.1.10.1.1.1.53	INTEGER	read-write	User input of channel number, which is an integer to N (N=Number of Channels).
INT sfpConfigXfpFreqError	1.3.6.1.4.1.4515.1.10.1.1.1.54	INTEGER	read-only	Frequency error reported in 16 bit signed integer with LSB=0.1 GHz.
T/F sfpConfigXfpDitherSupported	1.3.6.1.4.1.4515.1.10.1.1.1.55	TruthValue	read-only	Tx Dither Supported.
INT sfpConfigXfpDitherAdmin	1.3.6.1.4.1.4515.1.10.1.1.1.56	INTEGER	read-write	Enable/Disable the dithering function.
INT sfpConfigXfpCapFreqFirstThz	1.3.6.1.4.1.4515.1.10.1.1.1.57	INTEGER	read-only	Lasers First Frequency (THz) capability.
INT sfpConfigXfpCapFreqFirst10Ghz	1.3.6.1.4.1.4515.1.10.1.1.1.58	INTEGER	read-only	Lasers First Frequency (GHz*10) capability. This value should be added to sfpConfigXfpCapFreqFirstThz.
INT sfpConfigXfpCapFreqLastThz	1.3.6.1.4.1.4515.1.10.1.1.1.59	INTEGER	read-only	Lasers Last Frequency (THz) capability.
INT sfpConfigXfpCapFreqLast10Ghz	1.3.6.1.4.1.4515.1.10.1.1.1.60	INTEGER	read-only	Lasers Last Frequency (GHz*10) capability. This value should be added to sfpConfigXfpCapFreqLastThz.
INT sfpConfigXfpCapMaxSpacing10Ghz	1.3.6.1.4.1.4515.1.10.1.1.1.61	INTEGER	read-only	Lasers maximum supported grid spacing (GHz*10) capability.
T/F sfpConfigXfpCalibrationSupported	1.3.6.1.4.1.4515.1.10.1.1.1.62	TruthValue	read-only	Calibarion Supported.
T/F sfpConfigXfpCalibrationEnabled	1.3.6.1.4.1.4515.1.10.1.1.1.63	TruthValue	read-write	Enable/Disable the calibration process. Changing the value to Enable when a signal exist invokes an immidiate calibration process. Changing the value to Disable returns the calibration values to defaults.
INT sfpConfigCfpExtId	1.3.6.1.4.1.4515.1.10.1.1.1.70	INTEGER	read-only	Extended Identifier bit fields: Bits 7-6 - Power Class: 00b: Power Class 1 Module (? 8 W max), 01b: Power Class 2 Module (?16 W max), 10b: Power Class 3 Module (? 24 W max), 11b: Power Class 4 Module (? 32 W max). Bits 5-4 Lane Ratio: 00b: Network lane : Host lane = 1 : n (Mux type), 01b: Network lane : Host lane = n : m (Gear Box type), 10b: Network lane : Host lane = n : n (Parallel type), 11b: Reserved Bits 3-1 WDM Type: 000b: Non-WDM, 001b: CWDM, 010b: LANWDM, 011b: DWDM on 200G-grid, 100b: DWDM on 100G-grid, 101b: DWDM on 50G-grid, 110b: DWDM on 25G-grid, 111b: Other type WDM Bit 0 CLEI Presence: 0: No CLEI code present, 1: CLEI code present
INT sfpConfigCfpConnectorType	1.3.6.1.4.1.4515.1.10.1.1.1.71	INTEGER	read-only	Connector Type Code: 00h: Undefined, 01h : SC, 07h : LC, 08h : MT-RJ, 09h : MPO, Other Codes : Reserved
INT sfpConfigCfpEthernetCode	1.3.6.1.4.1.4515.1.10.1.1.1.72	INTEGER	read-only	Ethernet Application Code. 00h: Undefined type, 01h: 100GE SMF 10km, 100GE-LR4, 02h: 100GE SMF 40km, 100GE-ER4, 03h: 100GE MMF 100m OM3, 100GE-SR10, 04h: For future use, 05h: 40GE SMF 10km, 40GE-LR4, 07h: 40GE MMF 100m OM3, 40GE-SR4, For future use: 100G G.959.1 OTU4 40G G.693 SDH 40G G.693 OTU3 40G G.695 SDH 40G G.695 OTU3, 0Dh: 40GE-CR4 Copper 0Eh: 100GE-CR10 Copper, 0Fh: 40G BASE-FR, 10h~FFh: Reserved.
INT sfpConfigCfpFcCode	1.3.6.1.4.1.4515.1.10.1.1.1.73	INTEGER	read-only	Fiber Channel Application Code: Undefined
INT sfpConfigCfpCopperCode	1.3.6.1.4.1.4515.1.10.1.1.1.74	INTEGER	read-only	Copper Link Application Code: Undefined
INT sfpConfigCfpSonetCode	1.3.6.1.4.1.4515.1.10.1.1.1.75	INTEGER	read-only	SONET/SDH Application Code: 00h: Undefined type, 01h: VSR2000-3R2, 02h: VSR2000-3R3, 03h: VSR2000-3R5, 04h ~ 0FFh: Reserved
INT sfpConfigCfpOtnCode	1.3.6.1.4.1.4515.1.10.1.1.1.76	INTEGER	read-only	OTN Application Code: 0h: Undefined type, 01h: VSR2000-3R2F, 02h: VSR2000-3R3F, 03h: VSR2000-3R5F, 04h: VSR2000-3L2F, 05h: VSR2000-3L3F, 06h: VSR2000-3L5F, 07h: C4S1-2D1 (OTL3.4), 08h: 4I1-9D1F (OTL4.4), 09h ~ 0FFh: Reserved
INT sfpConfigCfpSupportedRates	1.3.6.1.4.1.4515.1.10.1.1.1.77	INTEGER	read-only	Additional Capable Rates Supported Bitmap: Bits 7-5 - Reserved Bit 4 - 111.8 Gbps Bit 3 - 103.125 Gbps Bit 2 - 41.25 Gbps Bit 1 - 43 Gbps Bit 0 - 39.8 Gbps
INT sfpConfigCfpSupportedLanes	1.3.6.1.4.1.4515.1.10.1.1.1.78	INTEGER	read-only	Number of Lanes Supported: Bits 7-4 - Number of Network Lanes The value of 0 represents 16 network lanes supported. The values of 1 through 15 represent the actual number of network lanes supported Bits 3-0 - Number of Host Lanes The value of 0 represents 16 network lanes supported. The values of 1 through 15 represent the actual number of network lanes supported
INT sfpConfigCfpMediaProperties	1.3.6.1.4.1.4515.1.10.1.1.1.79	INTEGER	read-only	Media Properties bit fields: Bits 7 - 6 Media Type: 00b: SMF , 01b: MMF (OM3), 10b: Reserved, 11b: Copper Bit 5 - Directionality: 0: Normal, 1: BiDi Bit 4 Optical Multiplexing and De-multiplexing: 0: Without optical MUX/DEMUX, 1: With optical MUX/DEMUX Bits 3 - 0 ctive Fiber per Connector: A 4-bit unsigned number representing number of active fibers for TX and RX per connector: 0: 16 TX Lanes and 16 RX Lanes, 1: 1 TX Lane and 1 RX Lane, 4: 4 TX Lanes and 4 RX Lanes, 10: 10 TX Lanes and 10 RX Lanes, 12: 12 TX Lanes and 12 RX Lanes
INT sfpConfigCfpMaxNetworkLaneRate	1.3.6.1.4.1.4515.1.10.1.1.1.80	INTEGER	read-only	Maximum Network Lane Bit Rate: 8-bit value x 0.2 Gbps
INT sfpConfigCfpMaxHostLaneRate	1.3.6.1.4.1.4515.1.10.1.1.1.81	INTEGER	read-only	Maximum Host Lane Bit Rate: 8-bit value x 0.2 Gbps
INT sfpConfigCfpMaxSmFiberLength	1.3.6.1.4.1.4515.1.10.1.1.1.82	INTEGER	read-only	Maximum Single Mode Optical Fiber Length: 8-bit value x 1 km for single mode fiber length
INT sfpConfigCfpMaxMmFiberLength	1.3.6.1.4.1.4515.1.10.1.1.1.83	INTEGER	read-only	Maximum Multi-Mode Optical Fiber Length: 8-bit value x 10 m for multi-mode fiber length
INT sfpConfigCfpMaxCopperCableLength	1.3.6.1.4.1.4515.1.10.1.1.1.84	INTEGER	read-only	Maximum Copper Cable Length: 8-bit value x 1 m for copper cable length
INT sfpConfigCfpMinWavelenPerActive	1.3.6.1.4.1.4515.1.10.1.1.1.85	INTEGER	read-only	Minimum Wavelength per Active Fiber: 16-bit unsigned value x 0.025 nm. (MSB is at 8012h, LSB is at 8013h)
INT sfpConfigCfpMaxWavelenPerActive	1.3.6.1.4.1.4515.1.10.1.1.1.86	INTEGER	read-only	Maximum Wavelength per Active Fiber: 16-bit unsigned value x 0.025 nm. (MSB is at 8014h, LSB is at 8015h)
INT sfpConfigCfpMaxLenOpticalWidth	1.3.6.1.4.1.4515.1.10.1.1.1.87	INTEGER	read-only	Maximum per Lane Optical Width: Guaranteed range of laser wavelength. 16-bit unsigned value x 1 pm. (MSB is at 8016h, LSB is at 8017h)
INT sfpConfigCfpSpacing	1.3.6.1.4.1.4515.1.10.1.1.1.88	INTEGER	read-write	The spacing between two lanes: 0- unknown spacing 1 - 100G spacing 2 - 50G spacing 3- 25G spacing
INT sfpConfigQsfppEthernetCode	1.3.6.1.4.1.4515.1.10.1.1.1.100	INTEGER	read-only	Maximum per Lane Optical Width: Guaranteed range of laser wavelength. 16-bit unsigned value x 1 pm. (MSB is at 8016h, LSB is at 8017h)
INT sfpConfigQsfppSonetCode	1.3.6.1.4.1.4515.1.10.1.1.1.101	INTEGER	read-write	The spacing between two lanes: 0- unknown spacing 1 - 100G spacing 2 - 50G spacing 3- 25G spacing
INT sfpConfigCxpExtId	1.3.6.1.4.1.4515.1.10.1.1.1.110	INTEGER	read-write	Extended Identifier (Byte 129): Bits 7-5 - Power Class: 000: 0.25W max - Class 0 001: 1.0W max - Class 1 010: 1.5W max - Class 2 011: 2.5W max - Class 3 100: 4.0W max - Class 4 101: 6.0W max - Class 5 110: >6.0W - Class 6 111: Reserved Bits 4 Tx CDR Presence: 1: Tx CDR provided 0: Otherwise Bits 3 Rx CDR Presence: 1: Rx CDR provided; 0: Otherwise
INT sfpConfigCxpConnectorType	1.3.6.1.4.1.4515.1.10.1.1.1.111	INTEGER	read-write	Connector Type Code (Byte 130): 30h: Passive Copper Cable Assembly 31h: Active Copper Cable Assembly (ref. Byte 147) 32h: Active Optical Cable Assembly 33h: Optical Transceiver w/ optical connector
INT sfpConfigCxpMaxSupportedRate	1.3.6.1.4.1.4515.1.10.1.1.1.112	INTEGER	read-write	Max per-channel bit rate (Byte 134): Max signal rate = binary value x 100 Mb/s
INT sfpConfigCxpNominalWavelength	1.3.6.1.4.1.4515.1.10.1.1.1.113	INTEGER	read-write	Wavelength/Attenuation (Bytes 135-136): Optical: Nominal Laser Wavelength -- Wavelength in nm = value / 20): e.g. 42h 04h = 16,900, 16,900/20 = 845 nm Copper: Nominal attenuation of cable either to the other end (passive) or to equalizer (active) Byte 135: Attenuation at 2.5 GHz in dB - 00h=no info Byte 136: Attenuation at 5 GHz in dB - 00h=no info
INT sfpConfigCxpDeviceTech	1.3.6.1.4.1.4515.1.10.1.1.1.114	INTEGER	read-write	Device Technology (Byte 147): Bits 7-4 (Device Technology): 0000: 850 nm VCSEL 0001:1310 nm VCSEL 0010:1550 nm VCSEL 0011: 1310 nm FP 0100:1310 nm DFB 0101:1550 nm DFB 0110: 1310 nm EML 0111: 1550 nm EML 1000: Copper or others 11001: 1490 nm DFB 1010: Copper cable un-equalized 1011: Copper cable passive equalized 1100: Copper cable near & far end active equalizers 1101: Copper cable, far end active equalizer 1110: copper cable, near end active equalizer 1111: Reserved Bit 3 (Wavelength Control): 0: No control 1: Active wavelength control Bit 2 (Transmitter cooling): 0: Uncooled transmitter 1: Cooled transmitter Bit 1 (Optical Detector): 0: P-I-N Detector 1: APD detector Bit 0 (Optical Tunability): 0: Transmitter not tunable 1:Transmitter tunable
INT sfpConfigCohRxDesiredChannel	1.3.6.1.4.1.4515.1.10.1.1.1.115	INTEGER	read-write	User input of RX channel number, which is an integer 1 to N (N=Number of Channels).
INT sfpConfigCohRxDesiredWl	1.3.6.1.4.1.4515.1.10.1.1.1.116	INTEGER	read-write	User input of RX Wavelength setpoint (in units of 50 picometers).
INT sfpConfigCohRxDesiredFreq	1.3.6.1.4.1.4515.1.10.1.1.1.117	INTEGER	read-write	User input of channel number, which is an integer to N (N=Number of Channels).
INT sfpConfigCohCurrentCD	1.3.6.1.4.1.4515.1.10.1.1.1.118	INTEGER	read-only	Current Chromatic Dispersion counter. Units are in ps/nm
INT sfpConfigCohCurrentOSNR	1.3.6.1.4.1.4515.1.10.1.1.1.119	INTEGER	read-only	Current SNR. Units are in 0.1dB
INT sfpConfigCohAverageOSNR	1.3.6.1.4.1.4515.1.10.1.1.1.120	INTEGER	read-only	Average SNR over PM interval. Units are in 0.1dB
sfpDiag	1.3.6.1.4.1.4515.1.10.2
sfpDiagTable	1.3.6.1.4.1.4515.1.10.2.1		not-accessible	The SFP diagnostic table. The table defines the status and control of the alarms and warnings of the SFP-1310 and the DWDM SFP-15xy modules.
sfpDiagEntry	1.3.6.1.4.1.4515.1.10.2.1.1		not-accessible	An entry in the SFP diagnostic table. The index to this table is the same as the ifIndex of the SFP. The SFP Diagnostic Table contain and entry for each SFP module.
NUM sfpDiagInterface	1.3.6.1.4.1.4515.1.10.2.1.1.1	InterfaceIndex	read-only	The Interface Index of the SFP (type=196).
INT sfpDiagHighTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.2	INTEGER	read-write	The threshold value for high temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagLowTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.3	INTEGER	read-write	The threshold value for low temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius..
INT sfpDiagHighTempWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.4	INTEGER	read-write	The threshold value for high temperature warning. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagLowTempWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.5	INTEGER	read-write	The threshold value for low temperature warning. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius..
INT sfpDiagHighVoltAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.6	INTEGER	read-write	The threshold value for high voltage alarm. The value 0 means 0 Volts. An increment on one is equivalent to 100 uVolt, yielding a total range of +6.55 Volts.
INT sfpDiagLowVoltAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.7	INTEGER	read-write	The threshold value for low voltage alarm. The value 0 means 0 Volts. An increment on one is equivalent to 100 uVolt, yielding a total range of +6.55 Volts.
INT sfpDiagHighVoltWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.8	INTEGER	read-write	The threshold value for high voltage warning. The value 0 means 0 Volts. An increment on one is equivalent to 100 uVolt, yielding a total range of +6.55 Volts.
INT sfpDiagLowVoltWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.9	INTEGER	read-write	The threshold value for low voltage warning. The value 0 means 0 Volts. An increment on one is equivalent to 100 uVolt, yielding a total range of +6.55 Volts.
INT sfpDiagHighTxBiasAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.10	INTEGER	read-write	The threshold value for high voltage alarm. The value 0 means 0 Volt. An increment on one is equivalent to 2 uA, yielding a total range of 0 to 131 mA.
INT sfpDiagLowTxBiasAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.11	INTEGER	read-write	The threshold value for low voltage alarm. The value 0 means 0 Volts. An increment on one is equivalent to 2 uA, yielding a total range of 0 to 131 mA.
INT sfpDiagHighTxBiasWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.12	INTEGER	read-write	The threshold value for high voltage warning. The value 0 means 0 Volt. An increment on one is equivalent to 2 uA, yielding a total range of 0 to 131 mA.
INT sfpDiagLowTxBiasWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.13	INTEGER	read-write	The threshold value for low voltage warning. The value 0 means 0 Volts. An increment on one is equivalent to 2 uA, yielding a total range of 0 to 131 mA.
INT sfpDiagHighTxPowerAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.14	INTEGER	read-write	The threshold value for high TX power alarm. The value 0 means 0 Volt. An increment on one is equivalent to 1 uW, yielding a total range of 0 to 65.535 mW.
INT sfpDiagLowTxPowerAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.15	INTEGER	read-write	The threshold value for low TX power alarm. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 65.535 mW.
INT sfpDiagHighTxPowerWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.16	INTEGER	read-write	The threshold value for high TX power warning. The value 0 means 0 Volt. An increment on one is equivalent to 1 uW, yielding a total range of 0 to 65.535 mW.
INT sfpDiagLowTxPowerWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.17	INTEGER	read-write	The threshold value for low TX power warning. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 65.535 mW.
INT sfpDiagHighRxPowerAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.18	INTEGER	read-write	The threshold value for high RX power alarm. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 6.5535 mW.
INT sfpDiagLowRxPowerAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.19	INTEGER	read-write	The threshold value for low RX power alarm. The value 0 means 0 Volt. An increment on one is equivalent to 1 uW, yielding a total range of 0 to 6.5535 mW.
INT sfpDiagHighRxPowerWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.20	INTEGER	read-write	The threshold value for high RX power warning. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 6.5535 mW.
INT sfpDiagLowRxPowerWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.21	INTEGER	read-write	The threshold value for low RX power warning. The value 0 means 0 Volt. An increment on one is equivalent to 1 uW, yielding a total range of 0 to 6.5535 mW.
INT sfpDiagHighLaserTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.22	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for high laser temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagLowLaserTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.23	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for low laser temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagHighLaserTempWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.24	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for high laser temperature warning. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagLowLaserTempWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.25	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for low laser temperature warning. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius.
INT sfpDiagHighWaveLenAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.26	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for high laser temperature alarm. The reportable wavelength range is 1000.00 � 1655.35nm with a resolution of 0.01nm.
INT sfpDiagLowWaveLenAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.27	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for low laser temperature alarm. The reportable wavelength range is 1000.00 � 1655.35nm with a resolution of 0.01nm.
INT sfpDiagHighWaveLenWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.28	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for high laser temperature warning. The reportable wavelength range is 1000.00 � 1655.35nm with a resolution of 0.01nm.
INT sfpDiagLowWaveLenWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.29	INTEGER	read-write	For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The threshold value for low laser temperature warning. The reportable wavelength range is 1000.00 � 1655.35nm with a resolution of 0.01nm.
INT sfpDiagHighTecCurrAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.30	INTEGER	read-write	The threshold value for high TEC current alarm. The reported TEC current is defined as a positive number for cooling and a negative number for heating starting at -3276.8. The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.
INT sfpDiagLowTecCurrAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.31	INTEGER	read-write	The threshold value for low TEC current alarm. The reported TEC current is defined as a positive number for cooling and a negative number for heating starting at -3276.8. The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.
INT sfpDiagHighTecCurrWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.32	INTEGER	read-write	The threshold value for high TEC current warning. The reported TEC current is defined as a positive number for cooling and a negative number for heating starting at -3276.8. The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.
INT sfpDiagLowTecCurrWrnThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.33	INTEGER	read-write	The threshold value for low TEC current warning. The reported TEC current is defined as a positive number for cooling and a negative number for heating starting at -3276.8. The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.
INT sfpDiagModuleTemperature	1.3.6.1.4.1.4515.1.10.2.1.1.34	INTEGER	read-only	Internally measured module temperature. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius. Temperature accuracy is vendor specific but must be better than �3 degrees Celsius over specified operating temperature and voltage.
INT sfpDiagSupplyVoltage	1.3.6.1.4.1.4515.1.10.2.1.1.35	INTEGER	read-only	Internally measured supply voltage in transceiver. The value 0 means 0 Volts. An increment on one is equivalent to 100 uVolt, yielding a total range of +6.55 Volts. Accuracy is vendor specific but must be better than �3% of the manufacturer�s nominal value over specified operating temperature and voltage.
INT sfpDiagTxBias	1.3.6.1.4.1.4515.1.10.2.1.1.36	INTEGER	read-only	Internally measured TX Bias Current. The value 0 means 0 Volt. An increment on one is equivalent to 2 uA, yielding a total range of 0 to 131 mA. Accuracy is vendor specific but must be better than �3dB over specified temperature and voltage. Data is not valid when the transmitter is disabled.
INT sfpDiagTxOutputPower	1.3.6.1.4.1.4515.1.10.2.1.1.37	INTEGER	read-only	Measured TX output power. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 6.5535 mW. For the vendor specified wavelength, accuracy shall be better than �3dB over specified temperature and voltage.
INT sfpDiagRxInputPower	1.3.6.1.4.1.4515.1.10.2.1.1.38	INTEGER	read-only	Measured RX input power. The value 0 means 0 Watts. An increment on one is equivalent to 0.1 uW, yielding a total range of 0 to 6.5535 mW. For the vendor specified wavelength, accuracy shall be better than �3dB over specified temperature and voltage.
INT sfpDiagRxLaserTemperature	1.3.6.1.4.1.4515.1.10.2.1.1.39	INTEGER	read-only	Measured Laser Temperature. For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius. Temperature accuracy is vendor specific but must be better than � 0.2 degrees Celsius over specified operating temperature and voltage.
INT sfpDiagRxMeasuredWavelength	1.3.6.1.4.1.4515.1.10.2.1.1.40	INTEGER	read-only	Measured Laser Wavelength. For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The wavelength is defined as: Wavelength = 1000nm + 0.01nm * 16 bit value. Thus, the reportable wavelength range is 1000.00 � 1655.35nm with a resolution of 0.01nm.
INT sfpDiagRxTecCurrent	1.3.6.1.4.1.4515.1.10.2.1.1.41	INTEGER	read-only	Measured Laser Temperature or Wavelength. For DWDM applications, the diagnostic interface report either laser wavelength or temperature, with a given module�s reporting defined by bit 1 of the object sfpConfigOptionalWdm. The reported TEC current is defined as a positive number for cooling and a negative number for heating starting at -3276.8. The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7, The accuracy of the TEC current monitor is vendor specific but must be better than �15% of the maximum TEC current as stored in the TEC Current High Alarm Threshold
INT sfpDiagAlarms	1.3.6.1.4.1.4515.1.10.2.1.1.42	INTEGER	read-only	This object indicates the Alarms of the SFP module. The sfpDiagAlarms is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) simultaneously. The various bit positions are: 0 Temp High Alarm Set when internal temperature exceeds high alarm level. 1 Temp Low Alarm Set when internal temperature is below low alarm level. 2 Vcc High Alarm Set when internal supply voltage exceeds high alarm level. 3 Vcc Low Alarm Set when internal supply voltage is below low alarm level. 4 TX Bias High Alarm Set when TX Bias current exceeds high alarm level. 5 TX Bias Low Alarm Set when TX Bias current is below low alarm level. 6 TX Power High Alarm Set when TX output power exceeds high alarm level. 7 TX Power Low Alarm Set when TX output power is below low alarm level. 8 RX Power High Alarm Set when Received Power exceeds high alarm level. 9 RX Power Low Alarm Set when Received Power is below low alarm level. 10 (15xy) Laser T/W High Alarm Set when laser temperature or wavelength exceeds high alarm level. 11 (15xy) Laser T/W Low Alarm Set when laser temperature or wavelength is below low alarm level. 12 (15xy) TEC Current High Alarm Set when TEC current exceeds high alarm level. 13 (15xy) TEC Current Low Alarm Set when TEC current is below low alarm level. 14 Retimer Loss Of Lock 15 Removed SFP 16 Rx Signal Detect alarm 17 Laser End of Life 18 Laser Tx Failure Indication.
INT sfpDiagAlarmsMask	1.3.6.1.4.1.4515.1.10.2.1.1.43	INTEGER	read-write	This object indicates the Masking of the Alarms of the SFP module. The sfpDiagAlarmsMask is a bit map. Any of the alarm and warning flags can be masked by writing a 1 to the corresponding bits. The various bit positions are: 0 Temp High Wanring Set when internal temperature exceeds high warning level. 1 Temp Low Wanring Set when internal temperature is below low warning level. 2 Vcc High Wanring Set when internal supply voltage exceeds high warning level. 3 Vcc Low Wanring Set when internal supply voltage is below low warning level. 4 TX Bias High Wanring Set when TX Bias current exceeds high warning level. 5 TX Bias Low Wanring Set when TX Bias current is below low warning level. 6 TX Power High Wanring Set when TX output power exceeds high warning level. 7 TX Power Low Wanring Set when TX output power is below low warning level. 8 RX Power High Wanring Set when Received Power exceeds high warning level. 9 RX Power Low Wanring Set when Received Power is below low warning level. 10 (15xy) Laser T/W High Wanring Set when laser temperature or wavelength exceeds high warning level. 11 (15xy) Laser T/W Low Wanring Set when laser temperature or wavelength is below low warning level. 12 (15xy) TEC Current High Wanring Set when TEC current exceeds high warning level. 13 (15xy) TEC Current Low Wanring Set when TEC current is below low warning level.
INT sfpDiagWarnings	1.3.6.1.4.1.4515.1.10.2.1.1.44	INTEGER	read-only	This object indicates the Warnings of the SFP module. The sfpDiagWarnings is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) simultaneously. The various bit positions are: 0 Temp High Warning Set when internal temperature exceeds high warning level. 1 Temp Low Warning Set when internal temperature is below low warning level. 2 Vcc High Warning Set when internal supply voltage exceeds high warning level. 3 Vcc Low Warning Set when internal supply voltage is below low warning level. 4 TX Bias High Warning Set when TX Bias current exceeds high warning level. 5 TX Bias Low Warning Set when TX Bias current is below low warning level. 6 TX Power High Warning Set when TX output power exceeds high warning level. 7 TX Power Low Warning Set when TX output power is below low warning level. 8 RX Power High Warning Set when Received Power exceeds high warning level. 9 RX Power Low Warning Set when Received Power is below low warning level. 10 Laser T/W High Warning Set when laser temperature or wavelength exceeds high warning level. 11 Laser T/W Low Warning Set when laser temperature or wavelength is below low warning level. 12 TEC Current High Warning Set when TEC current exceeds high warning level. 13 TEC Current Low Warning Set when TEC current is below low warning level.
INT sfpDiagWarningsMask	1.3.6.1.4.1.4515.1.10.2.1.1.45	INTEGER	read-write	This object indicates the Masking of the Warnings of the SFP module. The sfpDiagWarningsMask is a bit map. Any of the alarm and warning flags can be masked by writing a 1 to the corresponding bits. The various bit positions are: 0 Temp High Warning Set when internal temperature exceeds high warning level. 1 Temp Low Warning Set when internal temperature is below low warning level. 2 Vcc High Warning Set when internal supply voltage exceeds high warning level. 3 Vcc Low Warning Set when internal supply voltage is below low warning level. 4 TX Bias High Warning Set when TX Bias current exceeds high warning level. 5 TX Bias Low Warning Set when TX Bias current is below low warning level. 6 TX Power High Warning Set when TX output power exceeds high warning level. 7 TX Power Low Warning Set when TX output power is below low warning level. 8 RX Power High Warning Set when Received Power exceeds high warning level. 9 RX Power Low Warning Set when Received Power is below low warning level. 10 Laser T/W High Warning Set when laser temperature or wavelength exceeds high warning level. 11 Laser T/W Low Warning Set when laser temperature or wavelength is below low warning level. 12 TEC Current High Warning Set when TEC current exceeds high warning level. 13 TEC Current Low Warning Set when TEC current is below low warning level.
INT sfpDiagConfLowRxPowerAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.46	INTEGER	read-write	Configured threshold value for low RX power alarm. Changing this value doen't affect the SFP and is implemented by software. The threshold level specified in 0.1 dBm units. The range starts with -50.0 dBm.
FLO sfpDiagRxInputPowerFloat	1.3.6.1.4.1.4515.1.10.2.1.1.47	Float32TC	read-only	Measured RX input power sepcified in floating units. This object is used for power < -40dBm that can be achieved with SFP external calibration. When not used this value is 0 and sfpDiagRxInputPower should be used.
INT sfpDiagCxpTxTemp	1.3.6.1.4.1.4515.1.10.2.1.1.50	INTEGER	read-only	Internally measured Tx temperature. The value 0 means -128 Celsius. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 22-23 (Tx Lower Page)
INT sfpDiagCxpHighTxTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.51	INTEGER	read-only	The threshold value for high Tx temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 128-129 (Tx Upper Page)
INT sfpDiagCxpLowTxTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.52	INTEGER	read-only	The threshold value for low Tx temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 130-131 (Tx Upper Page)
INT sfpDiagCxpRxTemp	1.3.6.1.4.1.4515.1.10.2.1.1.53	INTEGER	read-only	Internally measured Rx temperature. The value 0 means -128 Celsius. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 22-23 (Rx Lower Page)
INT sfpDiagCxpHighRxTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.54	INTEGER	read-only	The threshold value for high Rx temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 128-129 (Rx Upper Page)
INT sfpDiagCxpLowRxTempAlmThreshold	1.3.6.1.4.1.4515.1.10.2.1.1.55	INTEGER	read-only	The threshold value for low Rx temperature alarm. The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree, yielding a total range of -128 to +128 Celsius For CXP Addr 130-131 (Rx Upper Page)
INT sfpDiagOtdrFiberCutRange	1.3.6.1.4.1.4515.1.10.2.1.1.56	INTEGER	read-only	The OTDR calculated range to the fiber cut
sfpTraps	1.3.6.1.4.1.4515.1.10.3
NTF sfpConfigChangeTrap	1.3.6.1.4.1.4515.1.10.3.1			A sfpTrapsChangeTrap trap is sent when the content of an instance sfpConfigEntry changes. It can be utilized by an NMS to trigger polls.
sfpTune	1.3.6.1.4.1.4515.1.10.4

RFC description

Monitors and configures Small Form-factor Pluggable (SFP) transceiver modules for optical network interfaces and diagnostics.

Start monitoring SmartOptics SiteLight optical transport platform, SFP transceiver module (digital diagnostics/compliance status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SL-SFP-MIB

What Is SL-SFP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description