UBQS-ENTITY-MIB

All MIBs › UBQS-ENTITY-MIB

Organization: Ubiquoss Corp.

Last Updated: 2009-06-16

Description: MIB for monitoring and configuring Field Replaceable Units (FRUs) and physical entities on Ubiquoss network devices, extending the standard ENTITY-MIB

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is UBQS-ENTITY-MIB?

UBQS-ENTITY-MIB is a Ubiquoss proprietary MIB extending the standard ENTITY-MIB (RFC 2737) with monitoring and control of Field Replaceable Units (FRUs) and other physical entities on Ubiquoss access/aggregation equipment. Its module table records module ID/type, operational status and last-change time, serial number, slot/port number, and a control action, while a parallel slot table tracks per-slot module presence and status, alongside sensor-monitoring and transceiver-monitoring objects. As a hardware-status MIB it lets an administrator confirm a FRU's operational status and serial number, and trigger control actions like a module reset. It is deployed on Ubiquoss access/aggregation equipment. Engineers can download the UBQS-ENTITY-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UBQS-ENTITY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ubiquoss access/aggregation equipment

Monitoring Examples

An administrator checks ubiModuleOperStatus and ubiModuleStatusLastChangeTime to confirm when a FRU last changed state, before deciding whether a ubiModuleAction reset is warranted.

What Can Be Monitored

FRU/module operational status
slot presence

Imported Objects

From ENTITY-MIB

entPhysicalContainedIn	OBJECT-TYPE
entPhysicalDescr	OBJECT-TYPE
entPhysicalIndex	OBJECT-TYPE
entPhysicalName	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From UBQS-SMI

ubiMgmtv2

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using ubiIEEE1588SlotOperStatus OID:

Select an Ubiquoss access/aggregation equipment (FRU/physical-entity operational status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ubiIEEE1588SlotOperStatus into the Find box to locate it in the OID tree, then select it and click OK. The operational status of the slot for IEEE 1588 specification. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value changes unexpectedly, since whether this slot should be equipped depends on your hardware configuration. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ubiEntityMIB	1.3.6.1.4.1.7800.100.3			The UBQS-ENTITY-MIB is used to monitor and configure operational status of Field Replaceable Units (FRUs) and other managable physical entities of the system listed in the Entity-MIB (RFC 2737) entPhysicalTable.
ubiEntityMIBObjects	1.3.6.1.4.1.7800.100.3.1
ubiEntityNotificationEnables	1.3.6.1.4.1.7800.100.3.1.1
T/F ubiFRUControlEnabled	1.3.6.1.4.1.7800.100.3.1.1.1	TruthValue	read-write	This variable indicates whether the system produces the following notifications: ubiEntityFRUInserted, ubiEntityFRURemoved. A false value will prevent these notifications from being generated.
T/F ubiEntSensorThresholdNotificationEnabled	1.3.6.1.4.1.7800.100.3.1.1.2	TruthValue	read-write	This variable indicates whether the system produces the following notification: ubiEntSensorThreshold. A false value will prevent these notifications from being generated.
ubiModuleTable	1.3.6.1.4.1.7800.100.3.1.2		not-accessible	This table contains one row per module entity.
ubiModuleEntry	1.3.6.1.4.1.7800.100.3.1.2.1		not-accessible	Information about a particular module entity.
INT ubiModuleId	1.3.6.1.4.1.7800.100.3.1.2.1.1	INTEGER	read-only	The unique module ID.
STR ubiModuleType	1.3.6.1.4.1.7800.100.3.1.2.1.2	DisplayString	read-only	The textual type of this module.
MOD ubiModuleOperStatus	1.3.6.1.4.1.7800.100.3.1.2.1.3	ModuleOperType	read-only	The operational state of this module.
TIM ubiModuleStatusLastChangeTime	1.3.6.1.4.1.7800.100.3.1.2.1.4	TimeStamp	read-only	The value of sysUpTime when ubiModuleOperStatus is changed.
STR ubiModuleSerialNumber	1.3.6.1.4.1.7800.100.3.1.2.1.5	DisplayString	read-only	The serial number of this module.
I32 ubiModuleSlotNumber	1.3.6.1.4.1.7800.100.3.1.2.1.6	Integer32	read-only	This value is determined by the number of slot where the module is located.
I32 ubiModulePortNumber	1.3.6.1.4.1.7800.100.3.1.2.1.7	Integer32	read-only	This value is determined by the number of port where the module is located.
INT ubiModuleAction	1.3.6.1.4.1.7800.100.3.1.2.1.8	INTEGER	read-write	This object, when read, returns one of the following results: other(1): module permanently enabled Setting this object to one of the acceptable values gives the following results: other(1): gives an error reset(2): resets the module's control logic Setting this object to any other values results in an error.
ubiSlotTable	1.3.6.1.4.1.7800.100.3.1.3		not-accessible	This table contains one row per slot entity.
ubiSlotEntry	1.3.6.1.4.1.7800.100.3.1.3.1		not-accessible	Information about a particular slot entity.
INT ubiSlotModuleId	1.3.6.1.4.1.7800.100.3.1.3.1.1	INTEGER	read-only	The unique module ID.
INT ubiSlotId	1.3.6.1.4.1.7800.100.3.1.3.1.2	INTEGER	read-only	The unique slot ID.
STR ubiSlotType	1.3.6.1.4.1.7800.100.3.1.3.1.3	DisplayString	read-only	The textual type of this slot.
MOD ubiSlotOperStatus	1.3.6.1.4.1.7800.100.3.1.3.1.4	ModuleOperType	read-only	The status of this slot.
I32 ubiSlotPortNumber	1.3.6.1.4.1.7800.100.3.1.3.1.5	Integer32	read-only	This value is determined by the number of port where the slot is located.
STR ubiSlotSerialNumber	1.3.6.1.4.1.7800.100.3.1.3.1.6	DisplayString	read-write	The serial number of this slot.
ubiExtSlot	1.3.6.1.4.1.7800.100.3.1.4
INT ubiIEEE1588SlotOperStatusEx	1.3.6.1.4.1.7800.100.3.1.4.1	INTEGER	read-only	The operational status of the slot for IEEE 1588 specification.
INT ubiMngSlotOperStatus	1.3.6.1.4.1.7800.100.3.1.4.2	INTEGER	read-only	The operational status of the slot for mng specification.
ubiTransceiver	1.3.6.1.4.1.7800.100.3.1.5
ubiEntitySensorTable	1.3.6.1.4.1.7800.100.3.1.5.1		not-accessible	This table contains objects which provide information about the transceiver sensor of physical entity.
ubiEntitySensorEntry	1.3.6.1.4.1.7800.100.3.1.5.1.1		not-accessible	An entry containing management information applicable to the transceiver sensor of a particular physical entity.
UBI ubiEntSensorType	1.3.6.1.4.1.7800.100.3.1.5.1.1.1	UbiSensorDataType	read-only	This variable indicates the type of data reported by the entSensorValue. valid values are: other(1): a measure other than those listed below unknown(2): unknown measurement, or arbitrary, relative numbers voltsAC(3): electric potential voltsDC(4): electric potential amperes(5): electric current celsius(6): temperature dBm(7): dB relative to 1mW of power
UBI ubiEntSensorScale	1.3.6.1.4.1.7800.100.3.1.5.1.1.2	UbiSensorDataScale	read-only	This variable indicates the exponent to apply to sensor values reported by entSensorValue.
UBI ubiEntSensorValue	1.3.6.1.4.1.7800.100.3.1.5.1.1.3	UbiSensorValue	read-only	This variable reports the most recent measurement seen by the sensor.
INT ubiEntSensorEventStatus	1.3.6.1.4.1.7800.100.3.1.5.1.1.4	INTEGER	read-only	This variable indicates the present current event status of the sensor.
TIM ubiEntSensorEventUpdateTime	1.3.6.1.4.1.7800.100.3.1.5.1.1.5	TimeStamp	read-only	The value of sysUpTime when the status of entity sensor is changed.
UBI ubiEntSensorAlarmHighThreshold	1.3.6.1.4.1.7800.100.3.1.5.1.1.6	UbiSensorValue	read-write	This variable indicates the value of the high alarm threshold.
UBI ubiEntSensorWarningHighThreshold	1.3.6.1.4.1.7800.100.3.1.5.1.1.7	UbiSensorValue	read-write	This variable indicates the value of the high warning threshold.
UBI ubiEntSensorWarningLowThreshold	1.3.6.1.4.1.7800.100.3.1.5.1.1.8	UbiSensorValue	read-write	This variable indicates the value of the low warning threshold.
UBI ubiEntSensorAlarmLowThreshold	1.3.6.1.4.1.7800.100.3.1.5.1.1.9	UbiSensorValue	read-write	This variable indicates the value of the low alarm threshold.
STR ubiEntSensorName	1.3.6.1.4.1.7800.100.3.1.5.1.1.10	DisplayString	read-only	This variable indicates the name of the sensor entity.
ubiTransceiverInfoTable	1.3.6.1.4.1.7800.100.3.1.5.2		not-accessible	This table contains objects which provide information about the transceiver of physical entity.
ubiTransceiverInfoEntry	1.3.6.1.4.1.7800.100.3.1.5.2.1		not-accessible	An entry containing management information applicable to the transceiver of a particular physical entity.
OID ubiTcIdentifier	1.3.6.1.4.1.7800.100.3.1.5.2.1.1	UbiTcIdentifier	read-only	This variable indicates the transceiver indentifier. valid value are: unknown(0), other(1), gbic(2), module(3), sfp(4), xbi(5), xenpak(6), xfp(7), xff(8), xfpE(9), xpak(10), x2(11)
STR ubiTcVendorOUI	1.3.6.1.4.1.7800.100.3.1.5.2.1.2	DisplayString	read-only	This variable indicates a textual string containing information about the IEEE company ID of transceiver vendor
STR ubiTcVendorName	1.3.6.1.4.1.7800.100.3.1.5.2.1.3	DisplayString	read-only	A textual string containing information about the transceiver name.
STR ubiTcVendorPartNumber	1.3.6.1.4.1.7800.100.3.1.5.2.1.4	DisplayString	read-only	A textual string containing information about the part number of the transceiver.
STR ubiTcVendorRevisionLevel	1.3.6.1.4.1.7800.100.3.1.5.2.1.5	DisplayString	read-only	A textual string containing information about the revision level of the transceiver part number.
STR ubiTcVendorSerialNumber	1.3.6.1.4.1.7800.100.3.1.5.2.1.6	DisplayString	read-only	This variable indicates a textual string containing information about the transceiver serial number.
STR ubiTcVendorManufacturingDate	1.3.6.1.4.1.7800.100.3.1.5.2.1.7	DisplayString	read-only	This variable indicates a manufacturing date of transceiver
I32 ubiTcWaveLength	1.3.6.1.4.1.7800.100.3.1.5.2.1.8	Integer32	read-only	This variable indicates a wave length of transceiver.
UBI ubiTcConnector	1.3.6.1.4.1.7800.100.3.1.5.2.1.9	UbiTcConnectorType	read-only	This variable indicates a connector type of transceiver.
I32 ubiTcLength	1.3.6.1.4.1.7800.100.3.1.5.2.1.10	Integer32	read-only	This variable indicates a length of transceiver.
T/F ubiTransceiverMonitoring	1.3.6.1.4.1.7800.100.3.1.5.3	TruthValue	read-write	This variable indicates whether the system produces the log and notification for transceiver sensor.
ubiEntityMIBNotificationPrefix	1.3.6.1.4.1.7800.100.3.2
ubiFruNotifications	1.3.6.1.4.1.7800.100.3.2.0
NTF ubiFRUInserted	1.3.6.1.4.1.7800.100.3.2.0.1			The ubiEntityFRUInserted notification indicates that a FRU was inserted. The varbind for this notification indicates the entPhysicalIndex of the inserted FRU, and the entPhysicalIndex of the FRU's container.
NTF ubiFRURemoved	1.3.6.1.4.1.7800.100.3.2.0.2			The ubiEntityFRURemoved notification indicates that a FRU was removed. The varbind for this notification indicates the entPhysicalIndex of the removed FRU, and the entPhysicalIndex of the FRU's container.
ubiEntitySensorNotifications	1.3.6.1.4.1.7800.100.3.2.1
NTF ubiEntSensorThreshold	1.3.6.1.4.1.7800.100.3.2.1.1			The ubiEntSensorThreshold notification indicates that the status of transceiver sensor was changed.
ubiEntityMIBConformance	1.3.6.1.4.1.7800.100.3.3
ubiEntityMIBCompliances	1.3.6.1.4.1.7800.100.3.3.1
ubiEntityMIBCompliance	1.3.6.1.4.1.7800.100.3.3.1.1			An Entity-MIB implementation can implement this group to provide FRU status and control.
ubiEntityMIBGroups	1.3.6.1.4.1.7800.100.3.3.2
ubiEntityMIBModuleGroup	1.3.6.1.4.1.7800.100.3.3.2.1			The collection of objects which are used to get the operational state and redundancy state of the modules
ubiEntitySlotGroup	1.3.6.1.4.1.7800.100.3.3.2.2			The collection of objects which are used to get the operational state and redundancy state of the slot.
ubiEntityMIBNotificationGroup	1.3.6.1.4.1.7800.100.3.3.2.3			TThe collection of objects which are used to send a notification.
ubiEntiryMIBIEEE1588SlotGroup	1.3.6.1.4.1.7800.100.3.3.2.4			The collection of objects which are used to get the operational state of the slot for IEEE 1588.
ubiEntityMIBTransceiverGroup	1.3.6.1.4.1.7800.100.3.3.2.5			The collection of objects which are used to get the information of transceiver.

RFC description

Ubiquoss entity management MIB for monitoring Field Replaceable Units (FRUs) and physical system entities.

Start monitoring Ubiquoss access/aggregation equipment (FRU/physical-entity operational status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UBQS-ENTITY-MIB