| OID symbolic | OID numeric | Type | Access | Description |
|---|
| salixSystemMIB | 1.3.6.1.4.1.2158.2.3 | | | The MIB describing System Objects
for SALIX products. These objects include error
reporting objects, and other system information objects |
| salixSystemMIBObjects | 1.3.6.1.4.1.2158.2.3.1 | | | |
| U32 salixSysLastLogErrorNumber | 1.3.6.1.4.1.2158.2.3.1.1 | Unsigned32 | read-only | The error number that is associate with the last set request. |
| STR salixSysLastLogErrorMessage | 1.3.6.1.4.1.2158.2.3.1.2 | DisplayString | read-only | The error message that describes the error associated with the
last set request. |
| OID salixSysLastLogErrorOid | 1.3.6.1.4.1.2158.2.3.1.3 | OBJECT IDENTIFIER | read-only | The last set request OID that produced an error. |
| I32 salixSysTemperature | 1.3.6.1.4.1.2158.2.3.1.4 | Integer32 | read-only | The temperature in degrees Celsius inside the chassis. |
| salixSystemSync | 1.3.6.1.4.1.2158.2.3.1.5 | | | |
| INT salixSysSyncTimingMode | 1.3.6.1.4.1.2158.2.3.1.5.1 | INTEGER | read-write | An identification of the source from which timing is derived by
the working sync module. Possible values are:
internal(1) - the internal oscillator on the sync module will be
used as the master clock for system synchronization.
line(2) - the sync module is synchronizing with the receive
line timing from a signal received by an LIU.
external(3) - an external timing interface will be used as the
master clock for system sychronization. |
| NUM salixSysSyncPrimaryRef | 1.3.6.1.4.1.2158.2.3.1.5.2 | InterfaceIndex | read-write | The interface index of the primary reference line from which
the sync module can derive timing. If the
'salixSysSyncTimingMode' is set to 'line' then this interface
index should identify a physical line termination point.
If the 'salixSysSyncTimingMode' is set to 'external' then this
interface index should identify a external timing interface. |
| NUM salixSysSyncSecondaryRef | 1.3.6.1.4.1.2158.2.3.1.5.3 | InterfaceIndex | read-write | The interface index of the secondary reference line from which
the sync module can derive timing. If the
'salixSysSyncTimingMode' is set to 'line' then this interface
index should identify a physical line termination point.
If the 'salixSysSyncTimingMode' is set to 'external' then this
interface index should identify an external timing interface.
The secondary reference line is only used if the
salixSysSyncTimingMode is set to 'line' or 'external' and the
primary reference line identified by 'salixSysSyncPrimaryRef'
has an oper status of 'down'. |
| T/F salixSysSyncRevertiveSwitch | 1.3.6.1.4.1.2158.2.3.1.5.4 | TruthValue | read-write | Indication of whether or not the active interface for deriving
timing should revert to the interface defined by the primary
reference line 'salixSysSyncPrimaryRef' if the primary
becomes available after a failure is cleared. This object is
only valid if the 'salixSysSyncTimingMode' is configured as
'line' or 'external'.
true(1) - reference switching is revertive
false(2) - reference switching is non-revertive |
| INT salixSysSyncClockMode | 1.3.6.1.4.1.2158.2.3.1.5.5 | INTEGER | read-only | Indication of the clock mode of the 'working' sync module.
freeRun(1) - mode in which the clock is synchronized to the
module's internal oscillator.
normal(2) - mode in which the clock is synchronized to an
external reference.
holdover(3) - mode in which the clock, after having been
synchronized to an external reference, loses that
reference and all other external references.
fastStart(4) - mode in which the clock is in the process of
synchronizing to a reference. |
| INT salixSysSyncConfiguredActiveRef | 1.3.6.1.4.1.2158.2.3.1.5.6 | INTEGER | read-write | The configured active reference line from which the sync module
should deriving its timing. This object is relevant if the
'salixSysSyncTimingMode' is set to 'line' or 'external'.
Writing a value that is different from its current value will
force the Sync module to switch to using the specified managed
object as the active reference line as indicated below:
primary(1) - The salixSysSyncPrimaryRef is the active
reference line
secondary(2) - The salixSysSyncSecondaryRef is the active
reference line |
| T/F salixSysSyncAutoRefSwitch | 1.3.6.1.4.1.2158.2.3.1.5.7 | TruthValue | read-write | Indication of automatic reference switching being enabled or
disabled.
true(1) - Auto reference switching is enabled
false(2) - Auto reference switching is disabled |
| T/F salixSysSyncFreeRunAlarm | 1.3.6.1.4.1.2158.2.3.1.5.8 | TruthValue | read-write | Indication of alarm associated with free-run mode being
enabled or disabled.
true(1) - Alarm is enabled
false(2) - Alarm is disabled |
| PHY salixSysSyncWorking | 1.3.6.1.4.1.2158.2.3.1.5.9 | PhysicalIndex | read-write | The entPhysicalIndex of the sync module plug-in unit that is
providing the system synchronizaton signal. Writing a new value
to this object, a value not equal to the current value, will:
- update the salixSysSyncProtect object with the current value
of the salixSysSyncWorking object and
- activate the specified sync module to start providing the
system synchronization signal.
A value of 0 indicates that there are no operational or not
installed sync modules in the system. Writing zero, an invalid
index, or the current value to this object will have no effect.
If the working sync module fails, the system will automatically
switch to the sync module specified in the salixSysSyncProtect
object. |
| PHY salixSysSyncProtect | 1.3.6.1.4.1.2158.2.3.1.5.10 | PhysicalIndex | read-only | The entPhysicalIndex of the sync module plug-in unit
that is protecting or on standby to the working sync module.
A value of 0 indicates that there is no redundant sync module
available or provisioned as a protect module. |
| INT salixSysSyncPrimaryRefState | 1.3.6.1.4.1.2158.2.3.1.5.11 | INTEGER | read-only | This variable indicates the state of the primary reference
line termination point to be used as a timing
source by the sync module. This object is relevant if the
salixSysSyncTimingMode is set to 'line' and the
salixSysSyncPrimaryRef is configured.
unknown(0) - the state of the line has not been
determined.
valid(1) - the line is operating within the
frequency specification.
lossOfSignalError - loss of signal was detected from the
line and has failed the health check.
frequencyOffsetError - frequency errors were detected from
the line and has failed the health check |
| INT salixSysSyncSecondaryRefState | 1.3.6.1.4.1.2158.2.3.1.5.12 | INTEGER | read-only | This variable indicates the state of the secondary reference
line termination point to be used as a timing
source by the sync module. This object is relevant if the
'salixSysSyncTimingMode' is set to 'line' and the
'salixSysSyncPrimaryRef' is configured.
unknown(0) - the state of the line has not been
determined.
valid(1) - the line is operating within
frequency specification.
lossOfSignalError - loss of signal was detected from the
line and has failed the health check.
frequencyOffsetError - frequency errors were detected from
the line and has failed the health check |
| INT salixSysSyncCurrentActiveRef | 1.3.6.1.4.1.2158.2.3.1.5.13 | INTEGER | read-only | Indication of the active reference line from which the sync
module is deriving its timing. This object is relevant if the
salixSysSyncTimingMode is set to 'line' or 'external'. The
value of this variable can differ from the
'salixSysSyncConfiguredActiveRef' if the sync module determines
an error condition with the 'salixSysSyncConfiguredActiveRef' and
has switched to using another line as the active reference.
primary(1) - The salixSysSyncPrimaryRef is the current
active reference line
secondary(2) - The salixSysSyncSecondaryRef is the current
active reference line |
| INT salixSysSyncForcedState | 1.3.6.1.4.1.2158.2.3.1.5.14 | INTEGER | read-only | This variable indicates the state of the sync module with
regard to switching between the configured active reference,
the value of the 'salixSysSyncConfiguredActiveRef' variable, and
the alternate active reference. The alternate active
reference is identified by the 'salixSysSyncPrimaryRef' or
'salixSysSyncSecondaryRef' that is not configured as the
'salixSysSyncConfiguredActiveRef'.
none(0) - the sync module is in a state where it is free
to switch between the configured active reference
the alternate active reference.
revertiveSwitchInhibit - the state of the sync module after
switching from the 'salixSysSyncConfiguredActiveRef'
to the 'salixSysSyncCurrentActiveRef' when the
'salixSysSyncRevertiveSwitch' is configured as 'false'.
In this state the sync module will not revert back
to using the 'salixSysSyncConfiguredActiveRef' unless
the 'salixSysSyncCurrentActiveRef' has failed and the
state of the active reference defined by the
'salixSysSyncConfiguredActiveRef' variable is 'valid'.
autoReferenceSwitchInhibit - the state of the sync module when
the 'salixSysSyncAutoReferenceSwitch' variable is
configured as 'false'. In this state the sync module
will not switch to using the alternate active reference
unless the 'salixSysSyncCurrentActiveRef' has failed and
the state of the alternate active reference is 'valid'. |
| salixSystemHsf | 1.3.6.1.4.1.2158.2.3.1.6 | | | |
| PHY salixSysHsfWorking | 1.3.6.1.4.1.2158.2.3.1.6.1 | PhysicalIndex | read-write | The PhysicalIndex of the Hybrid Switch Fabric (HSF) module
plug-in unit that is performing switching in the SALIX.
Writing a new value to this variable will:
- update the salixHsfProtect object with the current
value of the salixHsfWorking object and
- activate the specified HSF module to start performing
ATM and TDM switching in the system.
A value of 0 indicates that there is no operational switch
fabric installed. Writing zero, an invalid index,
or the current value to this object will have no effect.
If the working HSF module fails, the system will automatically
switch to the HSF module specified in the salixHsfProtect object. |
| PHY salixSysHsfProtect | 1.3.6.1.4.1.2158.2.3.1.6.2 | PhysicalIndex | read-only | The entPhysicalIndex of the Hybrid Switch Fabric (HSF) module
plug-in unit that is protecting or on standby to the working
HSF module, salixHSFWorking. A value of 0 indicates that there
are no operational or no additional HSF modules present for
redundancy. |
| salixSystemRsc | 1.3.6.1.4.1.2158.2.3.1.7 | | | |
| PHY salixSysRscWorking | 1.3.6.1.4.1.2158.2.3.1.7.1 | PhysicalIndex | read-write | The PhysicalIndex of the Redundant Shelf Controller (RSC) module
plug-in unit that is performing shelf controller operations
in the product (ie. talking with media controller, handling
SNMP requests). Writing a new value to this variable will:
- update the salixSysRscProtect object with the current
value of the salixSysRscWorking object and
- activate the specified RSC module to start performing
shelf controller operations in the system.
A value of 0 indicates that there is no operational shelf
controller installed. Writing zero, an invalid index,
or the current value to this object will have no effect.
If the working RSC module fails, the system will automatically
switch to the RSC module specified in the salixRscProtect object. |
| PHY salixSysRscProtect | 1.3.6.1.4.1.2158.2.3.1.7.2 | PhysicalIndex | read-only | The entPhysicalIndex of the Redundant Shelf Controller (RSC) module
plug-in unit that is protecting or on standby to the working
RSC module, salixRscWorking. A value of 0 indicates that there
are no operational or no additional RSC modules present for
redundancy. |
| OCT salixSysLoginMessage | 1.3.6.1.4.1.2158.2.3.1.8 | OCTET STRING | read-write | The message is displayed every time a user logs into the
CLI. It may be used to display legal warnings. |
| salixSystemMIBTraps | 1.3.6.1.4.1.2158.2.3.2 | | | |
| salixSystemMIBTrapPrefix | 1.3.6.1.4.1.2158.2.3.2.0 | | | |
| NTF salixSysSyncRefLineAlarm | 1.3.6.1.4.1.2158.2.3.2.0.1 | | | Indicates that the Sync plug-in unit associated with the
specified physical entity detected an error condition with
the interface configured as a reference.
The default alarm severity for this alarm is 'minor'. |
| NTF salixSysSyncInvalidRefLineAlarm | 1.3.6.1.4.1.2158.2.3.2.0.2 | | | Indicates that the Sync plug-in unit associated with the
specified physical entity does not have a valid primary
or secondary reference line for deriving timing. The
default alarm severity for this alarm is 'major'. |
| NTF salixSysSyncClockModeAlarm | 1.3.6.1.4.1.2158.2.3.2.0.3 | | | Indicates that the clock mode of the working or protect
Sync plug-in unit associated with the specified physical
entity, 'atmfM4PlugInUnitAvailStatus', changed to or from
'normal'. The default alarm severity for this alarm is
'major'. |
| NTF salixSysSyncClockModeStateChange | 1.3.6.1.4.1.2158.2.3.2.0.4 | | | Indicates that the clock mode of the working or protect
Sync plug-in unit associated with the specified physical
entity, 'atmfM4PlugInUnitAvailStatus', changed. |
| NTF salixSysFileSystemUnavailable | 1.3.6.1.4.1.2158.2.3.2.0.5 | | | Indicates the System Filesystem is no longer available. This can indicate
the loss of connectivity to the NFS server, or loss of the hard disk in systems
with a physical disk |
| salixSystemMIBCompliance | 1.3.6.1.4.1.2158.2.3.3 | | | |
| salixSystemGroups | 1.3.6.1.4.1.2158.2.3.3.1 | | | |
| salixSystemGroup | 1.3.6.1.4.1.2158.2.3.3.1.1 | | | Salix Error Objects Group |
| salixSystemCompliances | 1.3.6.1.4.1.2158.2.3.3.2 | | | |
| salixSystemCompliance | 1.3.6.1.4.1.2158.2.3.3.2.1 | | | The basic implementation requirements for the SALIX-ERROR-MIB. |
