All MIBs › RAISECOM-OPTICAL-TRANSCEIVER-MIB
Organization: Raisecom, Inc.
Last Updated: 2010-05-19
Description: Raisecom optical transceiver monitoring MIB for reading SFP/SFP+ media type, optical power, and alarm thresholds on Raisecom network device interfaces
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is RAISECOM-OPTICAL-TRANSCEIVER-MIB?
RAISECOM-OPTICAL-TRANSCEIVER-MIB is a Raisecom vendor MIB providing Digital Diagnostic Monitoring (DDM) for SFP/SFP+ optical transceivers installed in Raisecom network devices, exposing transceiver identity and real-time optical health parameters. It surfaces per-interface transceiver inventory data (type, connector type, media type, vendor name/part number/serial number) alongside global controls for notifications, DDM, password checking, and a configurable polling interval. This is a hardware-health monitoring MIB focused on optical-interface status: it identifies which SFP module is installed in each port and, via DDM, watches for optical power, temperature, voltage, or bias-current drifting outside safe thresholds, a leading indicator of a failing transceiver or degrading fiber link before a hard outage occurs. It relies on the standard SFF-8472 Digital Diagnostic Monitoring specification for the underlying optical measurements it reports. It is typically deployed on Raisecom carrier/access switches, media converters, and PON equipment where admins need early warning of optical-layer degradation, relying on RAISECOM-OPTICAL-TRANSCEIVER-MIB SNMP monitoring of DDM parameters.
IPNetwork Monitor allows you to monitor SNMP objects defined in RAISECOM-OPTICAL-TRANSCEIVER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Raisecom metro/access Ethernet switch or media converter
- Raisecom PON/optical network equipment with SFP/SFP+ transceiver slots
Monitoring Examples
An administrator would poll raisecomOpticalTransceiverInfoTable/raisecomOpticalTransceiverInfoEntry to read raisecomOpticalTransceiverVendorName, raisecomOpticalTransceiverVendorPN, and raisecomOpticalTransceiverVendorSN to confirm which SFP is installed in a given port, and raisecomOpticalTransceiverType/raisecomOpticalTransceiverMediaType to verify it matches the expected fiber type. Enabling raisecomOpticalTransceiverDDMEnable and setting raisecomOpticalTransceiverPollInterval lets the device periodically sample optical power/temperature so a slowly dimming laser or rising receive-power deficit can be caught before the link drops. raisecomOpticalTransceiverNotifyEnable controls whether a trap fires when a DDM threshold is crossed.
What Can Be Monitored
- installed transceiver vendor/part/serial number
- transceiver type and media type (connector/fiber type)
- DDM optical power/temperature/voltage thresholds (via DDM enable)
- DDM polling interval
- transceiver alarm notifications
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From RAISECOM-BASE-MIB
| raisecomAgent | OBJECT-IDENTITY |
From RAISECOM-COMMON-MANAGEMENT-MIB
| raisecomNotificationLocation | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| TEXTUAL-CONVENTION |
From SWITCH-TC
| ClearVar |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| raisecomOpticalTransceiver | 1.3.6.1.4.1.8886.1.18 | This MIB module defines objects to monitor optical characteristics on the optical interfaces in a network element. | ||
| raisecomOpticalTransceiverGlobalEnable | 1.3.6.1.4.1.8886.1.18.1 | |||
| ENA raisecomOpticalTransceiverNotifyEnable | 1.3.6.1.4.1.8886.1.18.1.1 | EnableVar | read-write | This object specifies the generation of device notifications, enable or disable. this object belongs to xfp and sfp. |
| ENA raisecomOpticalTransceiverDDMEnable | 1.3.6.1.4.1.8886.1.18.1.2 | EnableVar | read-write | Enable or disable digitaldiagnotic on the device. this object belongs to xfp and sfp. |
| ENA raisecomOpticalTransceiverCheckPwdEnable | 1.3.6.1.4.1.8886.1.18.1.3 | EnableVar | read-write | This object specifies the status of password checking on the device, enable or disable. this object belongs to xfp. |
| INT raisecomOpticalTransceiverPollInterval | 1.3.6.1.4.1.8886.1.18.1.4 | INTEGER | read-write | This object specifies the value of poll-interval on the device. this object belongs to xfp and sfp. |
| raisecomOpticalTransceiverObjects | 1.3.6.1.4.1.8886.1.18.2 | |||
| raisecomOpticalTransceiverInfoGroup | 1.3.6.1.4.1.8886.1.18.2.1 | |||
| raisecomOpticalTransceiverInfoTable | 1.3.6.1.4.1.8886.1.18.2.1.1 | not-accessible | Trancetver information Table. | |
| raisecomOpticalTransceiverInfoEntry | 1.3.6.1.4.1.8886.1.18.2.1.1.1 | not-accessible | An entry in the raisecomOpticalTransceiverInfoTable. | |
| INT raisecomOpticalTransceiverType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.1 | INTEGER | read-only | This object specifies the physical type of the transceiver, such as xfp or sfp , and so on. this object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverConnectorType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.2 | INTEGER | read-only | This object specifies the connector type of the transceiver, unknown, sc, db9, hssdc, bnc-tnc, fiber-coaxial-head, fiber-outlet, lc, mt-rj, mu, sg, fiber-pigtail, mpo-parallel-optic , hssdcII, copper, rj45. this object belongs to xfp and sfp. |
| OCT raisecomOpticalTransceiverVendorName | 1.3.6.1.4.1.8886.1.18.2.1.1.1.3 | OCTET STRING | read-only | Vendor name of the interface. this object belongs to xfp and sfp. |
| OCT raisecomOpticalTransceiverVendorPN | 1.3.6.1.4.1.8886.1.18.2.1.1.1.4 | OCTET STRING | read-only | Vendor part number of the interface. this object belongs to xfp and sfp. |
| OCT raisecomOpticalTransceiverVendorSN | 1.3.6.1.4.1.8886.1.18.2.1.1.1.5 | OCTET STRING | read-only | Vendor serial number of the interface. this object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverMediaType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.6 | INTEGER | read-only | Types of the fiber, single-mode, multi-modeE50, multi-mode50,multi-mode625,copper. single-modeKm,multi-modeOM3 this object belongs to xfp and sfp. |
| I32 raisecomOpticalTransceiverTransmissionDistance | 1.3.6.1.4.1.8886.1.18.2.1.1.1.7 | Integer32 | read-only | The max distance which the interface could transmit, measured in meter. The object will be shown in unit of Km, and the precision is 0.001. this object belongs to xfp and sfp. |
| U32 raisecomOpticalTransceiverAbility | 1.3.6.1.4.1.8886.1.18.2.1.1.1.8 | Unsigned32 | read-only | This object specifies the ability of optical module digitaldiagnotic funtion. Currently, the digitaldiagnotic objects of our optical module inculde 16 parameters. this object has 32 bits, each bit represents a digital diagnotic parameter. if the bit value is 0, it means that the optical module does not provide digital diagnotic funtion for relative parameter.if the bit value is 1,it means that the optical module provides digital diagnotic funtion for relative parameter. this object belongs to xfp and sfp. The relation between parameters and bits is following: 32......16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: The relation between parameters and bits is following: 32......16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: But when the optical module is sfp, the 6 bit will represents the supplyVoltage of sfp. |
| INT raisecomOpticalTransceiverDDM | 1.3.6.1.4.1.8886.1.18.2.1.1.1.9 | INTEGER | read-only | This object specifies if the transceiver supports on digital diagnostic function, support or not support.To the xfp, the default value of this object is support. this object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverCalibrationType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.10 | INTEGER | read-only | This object specifies the calibration type of the transceiver, internal, external, unknown. this object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverRSSI | 1.3.6.1.4.1.8886.1.18.2.1.1.1.11 | INTEGER | read-only | This object specifies the calibration type of the transceiver, support or not support. this object belongs to xfp and sfp. |
| OCT raisecomOpticalTransceiverVendorRev | 1.3.6.1.4.1.8886.1.18.2.1.1.1.12 | OCTET STRING | read-only | the version number of the transceiver. this object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverBRMax | 1.3.6.1.4.1.8886.1.18.2.1.1.1.13 | INTEGER | read-only | the min data rate of the transceiver,mesured in Mbps . this object belongs to xfp and sfp. The object will be shown in unit of Gbps, and the precision is 0.1. |
| INT raisecomOpticalTransceiverBRMin | 1.3.6.1.4.1.8886.1.18.2.1.1.1.14 | INTEGER | read-only | the min data rate of the transceiver,mesured in Mbps. this object belongs to xfp and sfp.To the sfp, the min data rate value is equal to the max data rate value. The object will be shown in unit of Gbps, and the precision is 0.1. |
| INT raisecomOpticalTransceiverWavelengthContrl | 1.3.6.1.4.1.8886.1.18.2.1.1.1.15 | INTEGER | read-only | if the transceiver supports on wavelength control support,notsupport. this object belongs to xfp. |
| I32 raisecomOpticalTransceiverWavelength | 1.3.6.1.4.1.8886.1.18.2.1.1.1.16 | Integer32 | read-only | Wavelength of the interface, measured in pm(0.001nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01. |
| OCT raisecomOpticalTransceiverWaveTolerance | 1.3.6.1.4.1.8886.1.18.2.1.1.1.17 | OCTET STRING | read-only | the range of laser wavelength from nominal wavelength,mesured in pm(0.001*nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01. |
| OCT raisecomOpticalTransceiverCompatibility | 1.3.6.1.4.1.8886.1.18.2.1.1.1.18 | OCTET STRING | read-only | the compatibility type that the transceiver supports,such as 10GBASE-SR. this object belongs to xfp. |
| INT raisecomOpticalTransceiverPowerDissipation | 1.3.6.1.4.1.8886.1.18.2.1.1.1.19 | INTEGER | read-only | the max power dissipation of the transceiver, p1W5,p2W5,p3W5,exceed3W5. this object belongs to xfp. |
| INT raisecomOpticalTransceiverCDR | 1.3.6.1.4.1.8886.1.18.2.1.1.1.20 | INTEGER | read-only | the optical module supports on CDR fundtion. support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverRefClock | 1.3.6.1.4.1.8886.1.18.2.1.1.1.21 | INTEGER | read-only | if the transceiver requires outside reference clock required,notrequired. this object belongs to xfp. |
| INT raisecomOpticalTransceiverTransmitterType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.22 | INTEGER | read-only | The transmitter type of the transceiver,such as 850 nm VCSEL. this object belongs to xfp. |
| INT raisecomOpticalTransceiverCooled | 1.3.6.1.4.1.8886.1.18.2.1.1.1.24 | INTEGER | read-only | The transmitter cooled type of the transceiver cooled,uncooled. this object belongs to xfp. |
| INT raisecomOpticalTransceiverTunalbe | 1.3.6.1.4.1.8886.1.18.2.1.1.1.25 | INTEGER | read-only | The transmitter tunable type of the transceiver tunable,untunable. this object belongs to xfp. |
| INT raisecomOpticalTransceiverDetectorType | 1.3.6.1.4.1.8886.1.18.2.1.1.1.26 | INTEGER | read-only | The detector type of the transceiver pin, apd. this object belongs to xfp. |
| INT raisecomOpticalTransceiverLineLoopBack | 1.3.6.1.4.1.8886.1.18.2.1.1.1.27 | INTEGER | read-only | The transceiver support status of sideline loop-back control support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverXFILoopBack | 1.3.6.1.4.1.8886.1.18.2.1.1.1.28 | INTEGER | read-only | The transceiver support status of XFI loop-back control support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverVps | 1.3.6.1.4.1.8886.1.18.2.1.1.1.29 | INTEGER | read-only | This object specifies if the optical module supports on VPS support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverTxDis | 1.3.6.1.4.1.8886.1.18.2.1.1.1.30 | INTEGER | read-only | The transceiver support status of software control the transmitter status support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverStandby | 1.3.6.1.4.1.8886.1.18.2.1.1.1.31 | INTEGER | read-only | The transceiver support status of software control the standby mode. support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverInVpsLowPower | 1.3.6.1.4.1.8886.1.18.2.1.1.1.32 | INTEGER | read-only | The VPS in low power support status of the transceiver support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverOutVpsLowPower | 1.3.6.1.4.1.8886.1.18.2.1.1.1.33 | INTEGER | read-only | The VPS out low power support status of the transceiver support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverFEC | 1.3.6.1.4.1.8886.1.18.2.1.1.1.34 | INTEGER | read-only | The FEC support status of transceiver support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverCMU | 1.3.6.1.4.1.8886.1.18.2.1.1.1.35 | INTEGER | read-only | The CMU support status of transceiver support,notsupport. this object belongs to xfp. |
| INT raisecomOpticalTransceiverBR | 1.3.6.1.4.1.8886.1.18.2.1.1.1.36 | INTEGER | read-only | This object specifies the Nominal bitrate of the transceiver, 125Mbps, 155Mbps, 622Mbps, 1.25Gbps, 2.5Gbps. this object belongs to xfp and sfp. |
| raisecomOpticalTransceiverDDMGroup | 1.3.6.1.4.1.8886.1.18.2.2 | |||
| raisecomOpticalTransceiverDDMTable | 1.3.6.1.4.1.8886.1.18.2.2.1 | not-accessible | This table provides objects to monitor optical parameters in a network element. | |
| raisecomOpticalTransceiverDDMEntry | 1.3.6.1.4.1.8886.1.18.2.2.1.1 | not-accessible | An entry in the raisecomOpticalTransceiverMonTable provides objects to monitor an optical parameter at an optical interface. | |
| OPT raisecomOpticalTransceiverParameterType | 1.3.6.1.4.1.8886.1.18.2.2.1.1.1 | OpticalParameterType | not-accessible | This object specifies the optical parameter that is being monitored in this entry. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParameterValue | 1.3.6.1.4.1.8886.1.18.2.2.1.1.2 | OpticalParameterValue | read-only | This object gives the value measured for the particular optical parameter specified by the raisecomOpticalMonParameterType object. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParamHighAlarmThresh | 1.3.6.1.4.1.8886.1.18.2.2.1.1.3 | OpticalParameterValue | read-only | This object gives the high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by raisecomOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of raisecomOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParamHighWarningThresh | 1.3.6.1.4.1.8886.1.18.2.2.1.1.4 | OpticalParameterValue | read-only | This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by raisecomOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of raisecomOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParamLowAlarmThresh | 1.3.6.1.4.1.8886.1.18.2.2.1.1.5 | OpticalParameterValue | read-only | This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by raisecomOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of raisecomOpticalParameterValue is lower than the value of this object. This alarm will be indicated in the raisecomOpticalParamAlarmStatus object .. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParamLowWarningThresh | 1.3.6.1.4.1.8886.1.18.2.2.1.1.6 | OpticalParameterValue | read-only | This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by raisecomOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of raisecomOpticalParameterValue object is lower than the value of this object. For network elements in the status indications, this threshold violation will be indicated in the raisecomOpticalParamAlarmStatus object . This object belongs to xfp/sfp. |
| INT raisecomOpticalTransceiverParamAlarmStatus | 1.3.6.1.4.1.8886.1.18.2.2.1.1.7 | INTEGER | read-only | This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the object will be set. Otherwise, the object will be set to 1. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverParamAlarmLastValue | 1.3.6.1.4.1.8886.1.18.2.2.1.1.8 | OpticalParameterValue | read-only | This object indicates the optical parameter value at the last time a threshold related to a particular optical parameter was exceeded on the interface. If no threshold value is currently being exceeded, then the value '-1000000' is returned. This object belongs to xfp/sfp. |
| TIK raisecomOpticalTransceiverParamAlarmLastChange | 1.3.6.1.4.1.8886.1.18.2.2.1.1.9 | TimeTicks | read-only | This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded on the interface. This object belongs to xfp/sfp. |
| U32 raisecomOpticalTransceiverDDM15MinValidIntervals | 1.3.6.1.4.1.8886.1.18.2.2.1.1.10 | Unsigned32 | read-only | This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of previous 15 minute intervals for which the agent has some data. This object belongs to xfp/sfp. |
| U32 raisecomOpticalTransceiverDDM24HrValidIntervals | 1.3.6.1.4.1.8886.1.18.2.2.1.1.11 | Unsigned32 | read-only | This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The max value of this object is 7, it means that the user can look up 7days history information. This object belongs to xfp/sfp. |
| INT raisecomOpticalTransceiverDDMValidStatus | 1.3.6.1.4.1.8886.1.18.2.2.1.1.12 | INTEGER | read-only | This object indicates the parameter row is valid or invalid. The object value is 'valide' when the module is present and supporting digitaldiagnotic. The object value is 'invalid' when the module is absent, or when the module is present and not supporting digitaldiagnotic. This object belongs to xfp/sfp. |
| raisecomOpticalTransceiverPMGroup | 1.3.6.1.4.1.8886.1.18.2.3 | |||
| raisecomOpticalTransceiverPMCurrentTable | 1.3.6.1.4.1.8886.1.18.2.3.1 | not-accessible | This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval. | |
| raisecomOpticalTransceiverPMCurrentEntry | 1.3.6.1.4.1.8886.1.18.2.3.1.1 | not-accessible | An entry in the raisecomOpticalTransceiverPMCurrentTable. It contains performance monitoring data for a monitored optical parameter at an interface, collected over the current 15 minute or the current 24 hour interval. | |
| OPT raisecomOpticalTransceiverPMCurrentPeriod | 1.3.6.1.4.1.8886.1.18.2.3.1.1.1 | OpticalPMPeriod | not-accessible | This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMCurrentParamType | 1.3.6.1.4.1.8886.1.18.2.3.1.1.2 | OpticalParameterType | not-accessible | This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMCurrentMaxParam | 1.3.6.1.4.1.8886.1.18.2.3.1.1.3 | OpticalParameterValue | read-only | This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMCurrentMinParam | 1.3.6.1.4.1.8886.1.18.2.3.1.1.4 | OpticalParameterValue | read-only | This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMCurrentMeanParam | 1.3.6.1.4.1.8886.1.18.2.3.1.1.5 | OpticalParameterValue | read-only | This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp. |
| raisecomOpticalTransceiverPMIntervalTable | 1.3.6.1.4.1.8886.1.18.2.3.2 | not-accessible | This table stores performance monitoring data for the various optical parameters, collected over previous intervals. This table can have entries for one complete 24 hour interval and up to 96 complete 15 minute intervals. A system is required to store at least 4 completed 15 minute intervals. The number of valid 15 minute intervals in this table is indicated by the raisecomOpticalTransceiverDDM15MinValidIntervals object and the number of valid 24 hour intervals is indicated by the raisecomOpticalTransceiverDDM24HrValidIntervals object. when the optical module is removed from the device, the relative history records will be cleaned. | |
| raisecomOpticalTransceiverPMIntervalEntry | 1.3.6.1.4.1.8886.1.18.2.3.2.1 | not-accessible | An entry in the raisecomOpticalTransceiverPMIntervalTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. | |
| OPT raisecomOpticalTransceiverPMIntervalPeriod | 1.3.6.1.4.1.8886.1.18.2.3.2.1.1 | OpticalPMPeriod | not-accessible | This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours. This object belongs to xfp/sfp. |
| I32 raisecomOpticalTransceiverPMIntervalNumber | 1.3.6.1.4.1.8886.1.18.2.3.2.1.2 | Integer32 | not-accessible | A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMIntervalParamType | 1.3.6.1.4.1.8886.1.18.2.3.2.1.3 | OpticalParameterType | not-accessible | This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMIntervalMaxParam | 1.3.6.1.4.1.8886.1.18.2.3.2.1.4 | OpticalParameterValue | read-only | This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMIntervalMinParam | 1.3.6.1.4.1.8886.1.18.2.3.2.1.5 | OpticalParameterValue | read-only | This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp. |
| OPT raisecomOpticalTransceiverPMIntervalMeanParam | 1.3.6.1.4.1.8886.1.18.2.3.2.1.6 | OpticalParameterValue | read-only | This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp. |
| raisecomOpticalTransceiverStatusGroup | 1.3.6.1.4.1.8886.1.18.2.4 | |||
| raisecomOpticalTransceiverCurrentStatusTable | 1.3.6.1.4.1.8886.1.18.2.4.1 | not-accessible | This table stores the hard ware information and the information set by user of the transceiver. This object belongs to xfp/sfp. | |
| raisecomOpticalTransceiverCurrentStatusEntry | 1.3.6.1.4.1.8886.1.18.2.4.1.1 | not-accessible | An entry in the raisecomOpticalTransceiverCurrentStatusTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. This object belongs to xfp/sfp. | |
| INT raisecomOpticalTransceiverHwInfoAbsStatus | 1.3.6.1.4.1.8886.1.18.2.4.1.1.1 | INTEGER | read-only | This object specifies if the optical module is absent present,absent. This object belongs to xfp and sfp. |
| INT raisecomOpticalTransceiverHwInfoNRStatus | 1.3.6.1.4.1.8886.1.18.2.4.1.1.2 | INTEGER | read-only | This object specifies if the optical module is ready for operation. ready,notready. This object belongs to xfp. |
| INT raisecomOpticalTransceiverHwInfoRxLosStatus | 1.3.6.1.4.1.8886.1.18.2.4.1.1.3 | INTEGER | read-only | This object specifies if the optical module operation losses the receiving signal normal,loss. This object belongs to xfp. |
| INT raisecomOpticalTransceiverHwInfoStandby | 1.3.6.1.4.1.8886.1.18.2.4.1.1.4 | INTEGER | read-write | This object specifies if the optical module works under standby mode. normal,standby. This object belongs to xfp. |
| INT raisecomOpticalTransceiverHwInfoLaser | 1.3.6.1.4.1.8886.1.18.2.4.1.1.5 | INTEGER | read-write | This object specifies if the optical module laser is turned on on,off. This object belongs to xfp. |
| I32 raisecomOpticalTransceiverWaveLengthError | 1.3.6.1.4.1.8886.1.18.2.4.1.1.6 | Integer32 | read-only | This object specifies error between the actual wavelength and the wavelength set by the user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.001. |
| I32 raisecomOpticalTransceiverUserWaveLength | 1.3.6.1.4.1.8886.1.18.2.4.1.1.7 | Integer32 | read-write | This object specifies the wavelength value of the optical module set by user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01. |
| INT raisecomOpticalTransceiverUserDataRate | 1.3.6.1.4.1.8886.1.18.2.4.1.1.8 | INTEGER | read-write | This object specifies the data rate of the optical module set by user,measured in Mbps. This object belongs to xfp. The object will be shown in unit of Gbps, and the precision is 0.1. |
| INT raisecomOpticalTransceiverUserLineLoopBack | 1.3.6.1.4.1.8886.1.18.2.4.1.1.9 | INTEGER | read-write | This object specifies if the sideline loop-back is tuned on , user can change the loop back mode through the object. normal,lineLoopback. This object belongs to xfp. |
| INT raisecomOpticalTransceiverUserXFILoopBack | 1.3.6.1.4.1.8886.1.18.2.4.1.1.10 | INTEGER | read-write | This object specifies if the XFI loop-back is tuned on user can change the loop back mode through the object. normal,xfiLoopback. This object belongs to xfp. |
| ENA raisecomOpticalTransceiverPortNotifyEnable | 1.3.6.1.4.1.8886.1.18.2.4.1.1.11 | EnableVar | read-write | This object specifies the generation of a port notifications, enable or disable. This object belongs to xfp and sfp. |
| ENA raisecomOpticalTransceiverPortDDMEnable | 1.3.6.1.4.1.8886.1.18.2.4.1.1.12 | EnableVar | read-write | This object specifies the status of digitaldiagnotic on a port, enable or disable. This object belongs to xfp and sfp. |
| ENA raisecomOpticalTransceiverPortCheckPwdEnable | 1.3.6.1.4.1.8886.1.18.2.4.1.1.13 | EnableVar | read-write | This object specifies the status of password checking on a port, enable or disable. This object belongs to xfp. |
| I32 raisecomOpticalTransceiverTxFaultCount | 1.3.6.1.4.1.8886.1.18.2.4.1.1.14 | Integer32 | read-only | This object specifies the number of tx-fault signals. |
| CLE raisecomOpticalTransceiverTxFaultCountClear | 1.3.6.1.4.1.8886.1.18.2.4.1.1.15 | ClearVar | read-write | This object specifies clear the statistcs of tx-fault signals. |
| INT raisecomOpticalTransceiverSpecificationCheckStatus | 1.3.6.1.4.1.8886.1.18.2.4.1.1.16 | INTEGER | read-only | This object specifies the check status, accord(0)specifies the optical module accord with industrial. not-accord(2) specifies the optical module not accord with industrial. |
| INT raisecomOpticalTransceiverTxFaultStatus | 1.3.6.1.4.1.8886.1.18.2.4.1.1.17 | INTEGER | read-only | This object specifies the tx-fault status. |
| raisecomOpticalTransceiverNotifications | 1.3.6.1.4.1.8886.1.18.3 | |||
| NTF raisecomOpticalTransceiverAbsentTrap | 1.3.6.1.4.1.8886.1.18.3.1 | This notification is sent when the optical module is removed from the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverPresentTrap | 1.3.6.1.4.1.8886.1.18.3.2 | This notification is sent when the optical module is plugged into the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverNRAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.3 | This notification is sent when the transmitted or received data of optical module is invalid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverNRNormalTrap | 1.3.6.1.4.1.8886.1.18.3.4 | This notification is sent when the transmitted or received data of optical module is valid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxLosAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.5 | This notification is sent when the optical module receiving signal is lost. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxLosNormaTrap | 1.3.6.1.4.1.8886.1.18.3.6 | This notification is sent when the optical module receiving signal is back to normal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverCheckPwdFailureTrap | 1.3.6.1.4.1.8886.1.18.3.7 | This notification is sent when the optical module password checking is failed. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverCheckPwdSucceedTrap | 1.3.6.1.4.1.8886.1.18.3.8 | This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.9 | This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.3.10 | This notification is sent when the optical module parameter value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamWarningTrap | 1.3.6.1.4.1.8886.1.18.3.11 | This notification is sent when the optical module parameter value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.3.12 | This notification is sent when the optical module parameter value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserBackLightAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.13 | This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserBackLightAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.3.14 | This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserLifeAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.15 | This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserLifeAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.3.16 | This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamLowAlarmTrap | 1.3.6.1.4.1.8886.1.18.3.17 | This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamLowAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.3.18 | This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamLowWarningTrap | 1.3.6.1.4.1.8886.1.18.3.19 | This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverParamLowWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.3.20 | This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| raisecomOpticalTransceiverParamNotifications | 1.3.6.1.4.1.8886.1.18.4 | |||
| NTF raisecomOpticalTransceiverTemperatureAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.1 | This notification is sent when the optical module Temperature value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTemperatureAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.2 | This notification is sent when the optical module Temperature value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTemperatureWarningTrap | 1.3.6.1.4.1.8886.1.18.4.3 | This notification is sent when the optical module Temperature value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTemperatureWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.4 | This notification is sent when the optical module Temperature value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxbiasCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.5 | This notification is sent when the optical module Tx bias Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxbiasCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.6 | This notification is sent when the optical module Tx bias Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxbiasCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.7 | This notification is sent when the optical module Tx bias Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxbiasCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.8 | This notification is sent when the optical module Tx bias Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxPowerAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.9 | This notification is sent when the optical module Tx Power value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxPowerAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.10 | This notification is sent when the optical module Tx Power value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxPowerWarningTrap | 1.3.6.1.4.1.8886.1.18.4.11 | This notification is sent when the optical module Tx Power value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxPowerWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.12 | This notification is sent when the optical module Tx Power value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxPowerAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.13 | This notification is sent when the optical module Rx Power value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxPowerWarningTrap | 1.3.6.1.4.1.8886.1.18.4.14 | This notification is sent when the optical module Rx Power value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxPowerWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.15 | This notification is sent when the optical module Rx Power value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverRxPowerAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.16 | This notification is sent when the optical module Rx Power value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserTemperatureAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.17 | This notification is sent when the optical module Laser Temperature value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserTemperatureWarningTrap | 1.3.6.1.4.1.8886.1.18.4.18 | This notification is sent when the optical module Laser Temperature value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserTemperatureWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.19 | This notification is sent when the optical module Laser Temperature value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserTemperatureAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.20 | This notification is sent when the optical module Laser Temperature value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyVoltageAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.21 | This notification is sent when the optical module +5.0V supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyVoltageWarningTrap | 1.3.6.1.4.1.8886.1.18.4.22 | This notification is sent when the optical module +5.0V supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyVoltageWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.23 | This notification is sent when the optical module +5.0V supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyVoltageAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.24 | This notification is sent when the optical module +5.0V supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyVoltageAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.25 | This notification is sent when the optical module +3.3V supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyVoltageWarningTrap | 1.3.6.1.4.1.8886.1.18.4.26 | This notification is sent when the optical module +3.3V supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyVoltageWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.27 | This notification is sent when the optical module +3.3V supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyVoltageAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.28 | This notification is sent when the optical module +3.3V supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyVoltageAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.29 | This notification is sent when the optical module +1.8v supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyVoltageWarningTrap | 1.3.6.1.4.1.8886.1.18.4.30 | This notification is sent when the optical module +1.8v supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyVoltageWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.31 | This notification is sent when the optical module +1.8v supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyVoltageAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.32 | This notification is sent when the optical module +1.8v supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyVoltageAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.33 | This notification is sent when the optical module -5.2v supply Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyVoltageWarningTrap | 1.3.6.1.4.1.8886.1.18.4.34 | This notification is sent when the optical module -5.2v supply Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyVoltageWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.35 | This notification is sent when the optical module -5.2v supply Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyVoltageAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.36 | This notification is sent when the optical module -5.2v supply Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverApdBiasVoltageAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.37 | This notification is sent when the optical module APD Bias Voltage value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverApdBiasVoltageWarningTrap | 1.3.6.1.4.1.8886.1.18.4.38 | This notification is sent when the optical module APD Bias Voltage value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverApdBiasVoltageWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.39 | This notification is sent when the optical module APD Bias Voltage value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverApdBiasVoltageAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.40 | This notification is sent when the optical module APD Bias Voltage value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.41 | This notification is sent when the optical module +5.0V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.42 | This notification is sent when the optical module +5.0V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.43 | This notification is sent when the optical module +5.0V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP5V0supplyCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.44 | This notification is sent when the optical module +5.0V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.45 | This notification is sent when the optical module +3.3V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.46 | This notification is sent when the optical module +3.3V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.47 | This notification is sent when the optical module +3.3V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP3V3supplyCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.48 | This notification is sent when the optical module +3.3V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.49 | This notification is sent when the optical module +1.8V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.50 | This notification is sent when the optical module +1.8V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.51 | This notification is sent when the optical module +1.8V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverP1V8supplyCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.52 | This notification is sent when the optical module +1.8V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.53 | This notification is sent when the optical module -5.2V supply Current value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.54 | This notification is sent when the optical module -5.2V supply Current value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.55 | This notification is sent when the optical module -5.2V supply Current value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverN5V2supplyCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.56 | This notification is sent when the optical module -5.2V supply Current value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTecCurrentAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.57 | This notification is sent when the optical module TecCurrent value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTecCurrentWarningTrap | 1.3.6.1.4.1.8886.1.18.4.58 | This notification is sent when the optical module TecCurrent value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTecCurrentWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.59 | This notification is sent when the optical module TecCurrent value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTecCurrentAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.60 | This notification is sent when the optical module TecCurrent value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserWavelengthAlarmTrap | 1.3.6.1.4.1.8886.1.18.4.61 | This notification is sent when the optical module laserWavelength value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserWavelengthWarningTrap | 1.3.6.1.4.1.8886.1.18.4.62 | This notification is sent when the optical module laserWavelength value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserWavelengthWarningNormalTrap | 1.3.6.1.4.1.8886.1.18.4.63 | This notification is sent when the optical module laserWavelength value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverLaserWavelengthAlarmNormalTrap | 1.3.6.1.4.1.8886.1.18.4.64 | This notification is sent when the optical module laserWavelength value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxFaultTrap | 1.3.6.1.4.1.8886.1.18.4.65 | This notification is sent when the SFP optical module occures Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. | ||
| NTF raisecomOpticalTransceiverTxNormalTrap | 1.3.6.1.4.1.8886.1.18.4.66 | This notification is sent when the SFP optical module cancels the Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects. |
RFC description
This MIB module defines objects to monitor optical characteristics on the optical interfaces in a network element.
Start monitoring Raisecom metro/access Ethernet switch or media converter, PON/optical equipment (SFP/SFP+ DDM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.