| OID symbolic | OID numeric | Type | Access | Description |
|---|
| pdnReachDSL | 1.3.6.1.4.1.1795.2.24.2.6.20 | | | The Paradyne enterprise ReachDSL MIB.
This MIB is written specifically to facilitate
in the management of ReachDSL devices as well as
help in configuration of Spectrum Management
specific objects for ReachDSL products. |
| pdnReachDSLObjects | 1.3.6.1.4.1.1795.2.24.2.6.20.1 | | | |
| INT reachDSLSpectrumMgmtSelection | 1.3.6.1.4.1.1795.2.24.2.6.20.1.1 | INTEGER | read-write | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This object is used to Enable or Disable
Spectrum Management on this device. Enabling
this object limits the DSL speeds and the maximum
transmit power on each port based on line length in order
to meet local Spectrum Management guidelines.
The values that this object can accept are controlled
by the 'Mode' object. |
| INT reachDSLSpectrumMgmtZone | 1.3.6.1.4.1.1795.2.24.2.6.20.1.2 | INTEGER | read-only | This object shows the geographic location or the spectrum
zone used for spectrum management. It also represents
which Spectrum Management standard will be used on this
device to calculate the effective maximum 'Tx Rates' and
the maximum allowed 'Tx Power' to comply with Spectrum
Management regulations for that specific region.
Note: Spectrum Management must be Enabled for
'SpectrumMgmtZone' to take effect. |
| reachDSLSpectrumMgmtConfTable | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3 | | not-accessible | The ReachDSL Spectrum Management Configuration Table
This table is used for configuring spectrum management
objects. |
| reachDSLSpectrumMgmtConfEntry | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1 | | not-accessible | An entry in the ReachDSL Spectrum Management
Configuration table.
Note: This entry can be accessed only for ifIndex
values that belong to a physical interface.
e.g. for ifType = 'adsl'. |
| U32 reachDSLSpectrumMgmtConfEWL | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1.1 | Unsigned32 | read-write | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The Equivalent Working Length (EWL). The value selected
corresponds to the estimated length of the line in
feet - if 'EWLUnits' object is 'feet'.
meters - if 'EWLUnits' object is 'meters'.
This value is usually specified by the carrier and MUST
be in integral multiples of
500 feet, if 'EWLUnits' is 'feet'.
200 meters, if 'EWLUnits' is 'meters'.
The range of values that this object can take is determined
by the 'MinEWL' and 'MaxEWL' objects.
Changing this object may limit the maximum transmit power
and the effective DSL speeds at which the ports train up.
Note: This object will be used only if Spectrum Management
is enabled and 'LoopMeasurementMethod' is 'ewl'.
This object shares a mutual exclusion relationship
with 'ConfLoopLength' & 'ConfQuadMode' objects, as
only one of the three will be used for configuration
at any given instant of time. |
| INT reachDSLSpectrumMgmtConfLoopLength | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1.2 | INTEGER | read-write | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This entry specifies the loop length for the line. The
configurable values are short(1), medium(2) and long(3).
The 'Loop Length' feature can be used only if the
'reachDSLSpectrumMgmtSelection' object is Enabled and
the 'LoopMeasurementMethod' is 'loopLength'. Changing this
object may limit the maximum transmit power and the
effective DSL speeds at which ports train up.
Note: This object shares a mutual exclusion relationship
with the 'ConfEWL' & 'ConfQuadMode' objects.
i.e. only one of the three can be used for
configuration at one time. |
| INT reachDSLSpectrumMgmtConfAtucMaxTxPower | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1.3 | INTEGER | read-write | The maximum transmit power at the ATUC (in tenth dB).
This value will be based on the spectrum management
selection. It ranges from -140 to 120 in increments
of 10. |
| INT reachDSLSpectrumMgmtConfAturMaxTxPower | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1.4 | INTEGER | read-write | The maximum transmit power at the ATUR (in tenth dB).
This value will be based on the spectrum management
selection. It ranges from -140 to 120 in increments
of 10. |
| INT reachDSLSpectrumMgmtConfQuadMode | 1.3.6.1.4.1.1795.2.24.2.6.20.1.3.1.5 | INTEGER | read-write | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This entry specifies the quad cable configuration &
length for the line. The configurable values are
sameQuad(1), segregatedQuadUpto3km(2) and
segregatedQuadAbove3km(3). The 'Quad Mode' feature can be
used only if the 'reachDSLSpectrumMgmtSelection' object
is Enabled and the 'LoopMeasurementMethod' is 'quadMode'.
Changing this object may limit the maximum transmit power
and the effective DSL speeds at which ports train up.
Note: This object shares a mutual exclusion relationship
with the 'ConfEWL' & 'ConfLoopLength' objects.
i.e. only one of the three can be used for
configuration at one time. |
| reachDSLSpectrumMgmtLineInfoTable | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4 | | not-accessible | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The ReachDSL Spectrum Management Line Info Table.
This table gives information about the spectrum
management ranges that are applicable for each port,
based on the spectral requirements for the device. |
| reachDSLSpectrumMgmtLineInfoEntry | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1 | | not-accessible | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
An entry in the reachDSLSpectrumMgmtLineInfoTable table.
Note: This entry can be accessed only for ifIndex values
that belong to a physical interface.
e.g. for ifType = 'adsl'. |
| U32 reachDSLSpectrumMgmtAtucMaxTxRate | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.1 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This rate will be the max allowed Tx Rate(in bps) for
the port based on the Spectrum Management requirements for
ATUC in a particular spectral compliance configuration. |
| U32 reachDSLSpectrumMgmtAtucMinTxRate | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.2 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This rate will be the min allowed Tx Rate based on the
spectrum management requirements for the ATUC. The
MinTxRate will be upper bounded by
'reachDSLSpectrumMgmtAtucMaxTxRate' object. |
| INT reachDSLSpectrumMgmtAtucMaxTxPower | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.3 | INTEGER | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The maximum transmit power at the ATUC (in tenth dB).
This value will be based on the spectrum management
selection. |
| U32 reachDSLSpectrumMgmtAturMaxTxRate | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.4 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This rate will be the max allowed Tx Rate(in bps) for
the port based on the Spectrum Management requirements for
ATUC in a particular spectral compliance configuration. |
| U32 reachDSLSpectrumMgmtAturMinTxRate | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.5 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This rate will be the min allowed Tx Rate based on the
spectrum management requirements for the ATUR. The
MinTxRate will be upper bounded by
'reachDSLSpectrumMgmtAturMaxTxRate' object. |
| INT reachDSLSpectrumMgmtAturMaxTxPower | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.6 | INTEGER | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The maximum transmit power at the ATUR (in tenth dB). This
value will be based on the spectrum management selection. |
| U32 reachDSLSpectrumMgmtMinEWL | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.7 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The minimum value (in feet, if 'EWLUnits' is 'feet, or in
meters, if 'EWLUnits' is 'meters') that the 'ConfEWL'
object can accept. Together with the 'MaxEWL' object,
this object indicates the range of EWL when 'EWLUnits' is
either 'feet' or 'meters'.
Note : This object is valid only if the
'LoopMeasurementMethod' object is 'ewl'. |
| U32 reachDSLSpectrumMgmtMaxEWL | 1.3.6.1.4.1.1795.2.24.2.6.20.1.4.1.8 | Unsigned32 | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
The maximum value (in feet, if 'EWLUnits' is 'feet, or in
meters, if 'EWLUnits' is 'meters') that the 'ConfEWL'
object can accept. Together with the 'MinEWL' object,
this object indicates the range of EWL when 'EWLUnits' is
either 'feet' or 'meters'.
Note : This object is valid only if the
'LoopMeasurementMethod' object is 'ewl'. |
| reachDSLLineTable | 1.3.6.1.4.1.1795.2.24.2.6.20.1.5 | | not-accessible | The ReachDSL Line Table. |
| reachDSLLineEntry | 1.3.6.1.4.1.1795.2.24.2.6.20.1.5.1 | | not-accessible | An entry in the reachDSLLineTable.
Note: This entry can be accessed only for ifIndex values
that belong to a physical interface.
e.g. for ifType = 'adsl'. |
| INT reachDSLPotsDetectionVoltage | 1.3.6.1.4.1.1795.2.24.2.6.20.1.5.1.1 | INTEGER | read-write | This object defines the configurable voltage used to
detect the presence of POTS on the DSL line. The range
is 0-74 volts. The default value is 3 volts.
Note: This object can be accessed only for ifIndex
values that belong to a physical interface.
i.e. ifType = adsl/reachDSL. |
| STR reachDSLCircuitIdentifier | 1.3.6.1.4.1.1795.2.24.2.6.20.1.5.1.2 | DisplayString | read-write | The value of this object reflects the transmission
vendor's circuit identifier to facilitate troubleshooting.
Note: This object can be accessed only for ifIndex
values that belong to a physical interface.
e.g. for ifType = 'adsl'.
This object is deprecated in favor of ifAlias. It is
highly recommended that future implementations use
ifAlias to store the Circuit Identifier associated with
reach DSL interfaces. |
| INT reachDSLSpectrumMgmtLoopMeasurementMethod | 1.3.6.1.4.1.1795.2.24.2.6.20.1.6 | INTEGER | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This object indicates the measurement method used in
describing the Loop Length of a circuit. Following are the
details of each of the options:
none(1) - Indicates that the Spectral Compliance
is NOT dependant on any Loop Length
measurements or configurations.
loopLength(2) - The 'ConfLoopLength' object is used to
determine spectral compliance. The
'ConfEWL' & 'ConfQuadMode' objects are
not used in this mode.
ewl(3) - The 'ConfEWL' object is used to
configure the estimated loop length,
which is used to determine spectral
compliance. In this mode the
'ConfLoopLength' & 'ConfQuadMode'
objects are not used.
quadMode(4) - The 'ConfQuadMode' object is used to
determine spectral compliance. The
'ConfEWL' & 'ConfLoopLength' objects
are not used in this mode.
This object determines which of the three objects :
'ConfEWL', 'ConfLoopLength' or 'ConfQuadMode' is used
(if any) to enforce spectrally compliant maximum
'Tx Rates' and the maximum allowed 'Tx Power' on a given
circuit. |
| INT reachDSLSpectrumMgmtEWLUnits | 1.3.6.1.4.1.1795.2.24.2.6.20.1.7 | INTEGER | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This object indicates the units of measurement used in
describing the Estimated Working Length of a circuit.
Following are the details of each of the units:
none(1) - Indicates that the Spectral Compliance is
NOT dependant on the 'ConfEWL' object.
feet(2) - The 'ConfEWL' is measured and configured
in feet.
meters(3) - The 'ConfEWL' is measured and configured
in meters. |
| INT reachDSLSpectrumMgmtMode | 1.3.6.1.4.1.1795.2.24.2.6.20.1.8 | INTEGER | read-only | This object has been deprecated. The corresponding
object in the new pdn_spectrumMgmt.mib should be used
instead.
This object restricts the MAX-ACCESS of the 'Selection'
object.
Following are the details of each of the values:
enableOnly(1) - Indicates that the 'Selection' object
IS always 'enabled' and cannot be set
to 'disabled'.
disableOnly(2) - Indicates that the 'Selection' object
IS always 'disabled' and cannot be set
to 'enabled'.
both(3) - Indicates that the 'Selection' object
will accept both the 'enabled' and
'disabled' values. |
| pdnReachDSLConformance | 1.3.6.1.4.1.1795.2.24.2.6.20.2 | | | |
| pdnReachDSLGroups | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1 | | | |
| pdnReachDSLConfigurationGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.1 | | | A collection of configuration objects required
for providing access to configuration as well
as status information for reachDSL products. |
| pdnReachDSLInformationGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.2 | | | A collection of objects providing access meant
specifically for accessing information for
for reachDSL products. |
| pdnReachDSLDeprecatedGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.3 | | | A collection of objects that have been deprecated. |
| pdnReachDSLGeneralConfigGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.4 | | | A collection of configuration objects required for
providing access to configure all reachDSL interfaces. |
| pdnReachDSLGeneralInformationGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.5 | | | A collection of objects providing information applicable
to all reachDSL interfaces. |
| pdnReachDSLEWLModeGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.6 | | | A collection of objects providing configuration
access and information specific to reachDSL interfaces
whose loop/line length measurement method is EWL.
i.e.the reachDSLSpectrumMgmtLoopMeasurementMethod object
is 'ewl'. |
| pdnReachDSLLoopLengthModeGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.7 | | | A collection of object(s) providing configuration
access and information specific to reachDSL interfaces
whose loop/line length measurement method is Loop Length
(short/medium/long).
i.e.the reachDSLSpectrumMgmtLoopMeasurementMethod object
is 'loopLength'. |
| pdnReachDSLQuadModeGroup | 1.3.6.1.4.1.1795.2.24.2.6.20.2.1.8 | | | A collection of object(s) providing configuration
access and information specific to reachDSL interfaces
whose loop/line length measurement method is based on the
Quad configuration.
i.e.the reachDSLSpectrumMgmtLoopMeasurementMethod object
is 'quadMode'. |
| pdnReachDSLCompliances | 1.3.6.1.4.1.1795.2.24.2.6.20.2.2 | | | |
| pdnReachDSLCompliance | 1.3.6.1.4.1.1795.2.24.2.6.20.2.2.1 | | | The compliance statement for SNMP entities which manage
ReachDSL interfaces. |
| pdnReachDSLCompliance1 | 1.3.6.1.4.1.1795.2.24.2.6.20.2.2.2 | | | The compliance statement for SNMP entities which manage
ReachDSL interfaces. |
