All MIBs › LUM-OA-MIB
Organization: Infinera Corporation
Last Updated: 2019-06-28
Category: Optical Networking
Description: Manages optical amplifier gain and settings on Infinera DWDM transmission systems.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is LUM-OA-MIB?
LUM-OA-MIB is an Infinera-related SNMP MIB for managing optical amplifier (OA) interfaces and settings on DWDM transmission systems, including both the OA modules themselves and associated variable optical attenuator (VOA) client/line interfaces. It exposes general administrative objects (table sizes and last-change timestamps for OA, VOA, VOA-client, VOA-line, and OA-module tables) plus the underlying oaIfTable describing each amplifier interface's name and description. Its core use is monitoring the operational health of critical optical hardware: tracking OA and VOA table sizes and state-change timestamps lets an operator detect when an amplifier module has been added, removed, or has changed operational state, which directly affects optical signal power and overall link performance in a DWDM system. As part of the broader LUM-* MIB family it likely shares the alarm-severity textual convention defined in LUM-ALARM-MIB when reporting amplifier faults. It is deployed on Infinera DWDM transmission platforms where maintaining correct amplifier gain and attenuation is essential to long-haul optical signal integrity. Engineers can download the LUM-OA-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in LUM-OA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Infinera DWDM optical amplifier module
Monitoring Examples
An operator would poll oaGeneralOaIfTableSize and oaGeneralStateLastChangeTime to detect when an optical amplifier interface has been added or its state changed, then walk oaIfTable/oaIfEntry by oaIfIndex to read oaIfName and oaIfDescr for the specific amplifier affected. Tracking oaGeneralVoaClientIfTableSize and oaGeneralVoaLineIfTableSize alongside these changes helps correlate an amplifier gain problem with a change in the associated variable optical attenuator configuration on the client or line side.
What Can Be Monitored
- optical amplifier interface table size
- amplifier state last-change time
- amplifier interface name/description
- VOA client interface table size
- VOA line interface table size
- OA module table size
This MIB depends on
Related MIBs
Imported Objects
From LUM-REG
| lumModules | OBJECT-IDENTITY |
| lumOaMIB | OBJECT-IDENTITY |
From LUM-TC
| BoardOrInterfaceAdminStatus | |
| BoardOrInterfaceOperStatus | |
| CommandString | |
| FaultStatus | |
| LambdaFrequency | |
| MgmtNameString | |
| ObjectProperty | |
| PortNumber | |
| SlotNumber | |
| SubrackNumber |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| lumOaMIBModule | 1.3.6.1.4.1.8708.1.1.20 | The optical amplifier interface MIB. - General - Amplifier interfaces | ||
| lumOaConfs | 1.3.6.1.4.1.8708.2.19.1 | |||
| lumOaGroups | 1.3.6.1.4.1.8708.2.19.1.1 | |||
| oaGeneralGroup | 1.3.6.1.4.1.8708.2.19.1.1.1 | The general objects. | ||
| oaIfGroup | 1.3.6.1.4.1.8708.2.19.1.1.2 | The oa interface objects. | ||
| oaIfGroupV2 | 1.3.6.1.4.1.8708.2.19.1.1.3 | The oa interface objects. | ||
| oaIfGroupV3 | 1.3.6.1.4.1.8708.2.19.1.1.4 | The oa interface objects. | ||
| oaGeneralGroupV2 | 1.3.6.1.4.1.8708.2.19.1.1.5 | The general objects. (3.1) | ||
| oaIfGroupV4 | 1.3.6.1.4.1.8708.2.19.1.1.6 | The oa interface objects. (3.2) | ||
| oaIfGroupV5 | 1.3.6.1.4.1.8708.2.19.1.1.7 | The oa interface objects. (4.0) | ||
| oaIfGroupV6 | 1.3.6.1.4.1.8708.2.19.1.1.8 | The oa interface objects. (5.0) | ||
| oaVoaIfGroupV1 | 1.3.6.1.4.1.8708.2.19.1.1.9 | The voa interface objects. (5.0) | ||
| oaIfGroupV7 | 1.3.6.1.4.1.8708.2.19.1.1.10 | The oa interface objects. (6.0) | ||
| oaIfGroupV8 | 1.3.6.1.4.1.8708.2.19.1.1.11 | The oa interface objects. (10.0) | ||
| oaVoaClientIfGroupV1 | 1.3.6.1.4.1.8708.2.19.1.1.12 | The voa client interface objects. (10.0) | ||
| oaVoaLineIfGroupV1 | 1.3.6.1.4.1.8708.2.19.1.1.13 | The voa line interface objects. (10.0) | ||
| oaGeneralGroupV3 | 1.3.6.1.4.1.8708.2.19.1.1.14 | The general objects. (10.0) | ||
| oaVoaClientIfGroupV2 | 1.3.6.1.4.1.8708.2.19.1.1.15 | The voa client interface objects. (11.0) | ||
| oaModuleGroupV1 | 1.3.6.1.4.1.8708.2.19.1.1.16 | The module objects. (11.0) | ||
| oaGeneralGroupV4 | 1.3.6.1.4.1.8708.2.19.1.1.17 | The general objects. (11.0) | ||
| oaIfGroupV9 | 1.3.6.1.4.1.8708.2.19.1.1.18 | The oa interface objects. (11.0) | ||
| oaModuleGroupV2 | 1.3.6.1.4.1.8708.2.19.1.1.19 | The module objects. (12.0) | ||
| oaIfGroupV10 | 1.3.6.1.4.1.8708.2.19.1.1.20 | The oa interface objects. (15.0) | ||
| oaIfGroupV11 | 1.3.6.1.4.1.8708.2.19.1.1.21 | The oa interface objects. (17.0) | ||
| oaVoaClientIfGroupV3 | 1.3.6.1.4.1.8708.2.19.1.1.22 | The voa client interface objects. (19.0) | ||
| oaIfGroupV12 | 1.3.6.1.4.1.8708.2.19.1.1.23 | The oa interface objects. (20.0) | ||
| oaModuleGroupV3 | 1.3.6.1.4.1.8708.2.19.1.1.24 | The module objects. (23.0) | ||
| oaIfGroupV13 | 1.3.6.1.4.1.8708.2.19.1.1.25 | The oa interface objects. (23.0) | ||
| oaIfGroupV14 | 1.3.6.1.4.1.8708.2.19.1.1.26 | The oa interface objects. (24.0) | ||
| oaIfGroupV15 | 1.3.6.1.4.1.8708.2.19.1.1.27 | The oa interface objects. (27.0) | ||
| oaModuleGroupV4 | 1.3.6.1.4.1.8708.2.19.1.1.28 | The module objects. (28.0) | ||
| lumOaCompl | 1.3.6.1.4.1.8708.2.19.1.2 | |||
| lumOaBasicComplV1 | 1.3.6.1.4.1.8708.2.19.1.2.1 | Basic implementation requirements for the OA MIB V1. | ||
| lumOaBasicComplV2 | 1.3.6.1.4.1.8708.2.19.1.2.2 | Basic implementation requirements for the OA MIB V2. | ||
| lumOaBasicComplV3 | 1.3.6.1.4.1.8708.2.19.1.2.3 | Basic implementation requirements for the OA MIB V3. | ||
| lumOaBasicComplV4 | 1.3.6.1.4.1.8708.2.19.1.2.4 | Basic implementation requirements for the OA MIB V4 (3.1). | ||
| lumOaBasicComplV5 | 1.3.6.1.4.1.8708.2.19.1.2.5 | Basic implementation requirements for the OA MIB V5 (3.2). | ||
| lumOaBasicComplV6 | 1.3.6.1.4.1.8708.2.19.1.2.6 | Basic implementation requirements for the OA MIB V6 (4.0). | ||
| lumOaBasicComplV7 | 1.3.6.1.4.1.8708.2.19.1.2.7 | Basic implementation requirements for the OA MIB V7 (5.0). | ||
| lumOaBasicComplV8 | 1.3.6.1.4.1.8708.2.19.1.2.8 | Basic implementation requirements for the OA MIB V8 (6.0). | ||
| lumOaBasicComplV9 | 1.3.6.1.4.1.8708.2.19.1.2.9 | Basic implementation requirements for the OA MIB V9 (10.0). | ||
| lumOaBasicComplV10 | 1.3.6.1.4.1.8708.2.19.1.2.10 | Basic implementation requirements for the OA MIB V10 (11.0). | ||
| lumOaBasicComplV11 | 1.3.6.1.4.1.8708.2.19.1.2.11 | Basic implementation requirements for the OA MIB V11 (12.0). | ||
| lumOaBasicComplV12 | 1.3.6.1.4.1.8708.2.19.1.2.12 | Basic implementation requirements for the OA MIB V12 (15.0). | ||
| lumOaBasicComplV13 | 1.3.6.1.4.1.8708.2.19.1.2.13 | Basic implementation requirements for the OA MIB V13 (17.0). | ||
| lumOaBasicComplV14 | 1.3.6.1.4.1.8708.2.19.1.2.14 | Basic implementation requirements for the OA MIB V14 (19.0). | ||
| lumOaBasicComplV15 | 1.3.6.1.4.1.8708.2.19.1.2.15 | Basic implementation requirements for the OA MIB V14 (20.0). | ||
| lumOaBasicComplV16 | 1.3.6.1.4.1.8708.2.19.1.2.16 | Basic implementation requirements for the OA MIB V16 (23.0). | ||
| lumOaBasicComplV17 | 1.3.6.1.4.1.8708.2.19.1.2.17 | Basic implementation requirements for the OA MIB V16 (24.0). | ||
| lumOaBasicComplV18 | 1.3.6.1.4.1.8708.2.19.1.2.18 | Basic implementation requirements for the OA MIB V16 (27.0). | ||
| lumOaBasicComplV19 | 1.3.6.1.4.1.8708.2.19.1.2.19 | Basic implementation requirements for the OA MIB V17 (28.0). | ||
| lumOaMinimalGroups | 1.3.6.1.4.1.8708.2.19.1.3 | |||
| lumOaMinimalCompl | 1.3.6.1.4.1.8708.2.19.1.4 | |||
| lumOaMinimalComplV1 | 1.3.6.1.4.1.8708.2.19.1.4.1 | Minimal implementation requirements for the OA MIB V1. | ||
| lumOaMIBObjects | 1.3.6.1.4.1.8708.2.19.2 | |||
| oaGeneral | 1.3.6.1.4.1.8708.2.19.2.1 | |||
| DAT oaGeneralLastChangeTime | 1.3.6.1.4.1.8708.2.19.2.1.1 | DateAndTime | read-only | The time when the configuration of the MIB was last changed. |
| DAT oaGeneralStateLastChangeTime | 1.3.6.1.4.1.8708.2.19.2.1.2 | DateAndTime | read-only | The time when the state of the MIB was last changed. |
| U32 oaGeneralOaIfTableSize | 1.3.6.1.4.1.8708.2.19.2.1.3 | Unsigned32 | read-only | Size of table |
| U32 oaGeneralVoaIfTableSize | 1.3.6.1.4.1.8708.2.19.2.1.4 | Unsigned32 | read-only | Size of table |
| U32 oaGeneralVoaClientIfTableSize | 1.3.6.1.4.1.8708.2.19.2.1.5 | Unsigned32 | read-only | Size of table |
| U32 oaGeneralVoaLineIfTableSize | 1.3.6.1.4.1.8708.2.19.2.1.6 | Unsigned32 | read-only | Size of table |
| U32 oaGeneralOaModuleTableSize | 1.3.6.1.4.1.8708.2.19.2.1.7 | Unsigned32 | read-only | Size of table |
| oaIfList | 1.3.6.1.4.1.8708.2.19.2.2 | |||
| oaIfTable | 1.3.6.1.4.1.8708.2.19.2.2.1 | not-accessible | The interface list. | |
| oaIfEntry | 1.3.6.1.4.1.8708.2.19.2.2.1.1 | not-accessible | An entry in the interface list. | |
| U32 oaIfIndex | 1.3.6.1.4.1.8708.2.19.2.2.1.1.1 | Unsigned32 | read-only | An arbitrary index assigned to each entry. |
| STR oaIfName | 1.3.6.1.4.1.8708.2.19.2.2.1.1.2 | MgmtNameString | read-only | The management name of the interface, for example 'oa:1:2:1-2', where the first number indicates sub-rack, the second slot number and the third is the port number. Examples: oa:s:s:p - Optical amplifier interface |
| STR oaIfDescr | 1.3.6.1.4.1.8708.2.19.2.2.1.1.3 | DisplayString | read-write | User configurable label. |
| SUB oaIfSubrack | 1.3.6.1.4.1.8708.2.19.2.2.1.1.4 | SubrackNumber | read-create | The number of the subrack where the interface is located. |
| SLO oaIfSlot | 1.3.6.1.4.1.8708.2.19.2.2.1.1.5 | SlotNumber | read-create | The number of the slot where the interface is located. |
| POR oaIfTxPort | 1.3.6.1.4.1.8708.2.19.2.2.1.1.6 | PortNumber | read-create | The number of the port where the TX-side of the interface is located. |
| POR oaIfRxPort | 1.3.6.1.4.1.8708.2.19.2.2.1.1.7 | PortNumber | read-create | The number of the port where the RX-side of the interface is located. |
| U32 oaIfInvPhysIndexOrZero | 1.3.6.1.4.1.8708.2.19.2.2.1.1.8 | Unsigned32 | read-only | The row in the invPhysTable for this interface. Set to 0 if not known. |
| NUM oaIfAdminStatus | 1.3.6.1.4.1.8708.2.19.2.2.1.1.9 | BoardOrInterfaceAdminStatus | read-write | The administrative state for the interface. down - The interface should be inactive. service - The interface is activated but alarms are suppressed. Intended for use during service or re-configuration. When service is concluded adminStatus should be set to 'up' again. up - The interface should be activated when it becomes available. Alarms are not suppressed. This attribute can be written via SNMP. |
| NUM oaIfOperStatus | 1.3.6.1.4.1.8708.2.19.2.2.1.1.10 | BoardOrInterfaceOperStatus | read-only | The operational state for the interface. notPresent - The physical resources are not available. down - The interface is de-activated or the are faults preventing it from going to the 'up'-state. up - The interface is operational. |
| INT oaIfLaserStatus | 1.3.6.1.4.1.8708.2.19.2.2.1.1.11 | INTEGER | read-only | The operational state of the laser. off - The laser is turned off. on - The laser is turned on. |
| INT oaIfAmplifierType | 1.3.6.1.4.1.8708.2.19.2.2.1.1.12 | INTEGER | read-create | The type of amplifier for this interface. preAmp25GAd - pre-amplifier for 2.5 G, add-drop preAmp25GTm - pre-amplifier for 2.5 G, terminal multiplexor powAmp10G - power amplifier for 10 G preAmp10GAd - pre-amplifier for 10 G, add-drop preAmp10GTm - pre-amplifier for 10 G, terminal multiplexor constantGain - used for pre-amps and other point-to-point links. Uses ASE compensation. => specify wantedGain constantGainLI - Default value. Works as constantGain but uses low input power mode. Please, refer to OA commissioning manual to decideoaIfRxSignalStatus which gain mode that should be used. constantGainHI - Works as constantGain but uses high input power mode. Please, refer to OA commissioning manual to decide which gain mode that should be used. constantSignalPower - used in combination with 2 channel add-drop filters. Uses ASE compensation. => specify wantedSignalPower constantPower - For test purposes No ASE compensation. => specify wantedAbsolutePower |
| I32 oaIfWantedAbsolutePowerLevel | 1.3.6.1.4.1.8708.2.19.2.2.1.1.13 | Integer32 | read-write | For powAmp10G and constantPower, the user can give the wanted absolute power level in units of 0.1 dBm. For OA10 and OA17 in constantGain and constantSignalPower, this parameter shows the derived absolute power level. The value is calculated from the other given parameters. |
| I32 oaIfWantedRelativePowerLevel | 1.3.6.1.4.1.8708.2.19.2.2.1.1.14 | Integer32 | read-write | Wanted offset from production setting in units of 0.1 dBm. Applicable for preAmp25GAd and preAmp10GAd. Note that the output power level is dependent on the power of the input signal, so you might not always get the power that you want. |
| I32 oaIfWantedGain | 1.3.6.1.4.1.8708.2.19.2.2.1.1.15 | Integer32 | read-write | Signal gain setting in units of 0.1 dB. Applicable for preAmp25GTm, preAmp10GTm and constantGain/LI/HI. This attribute can be written via SNMP. |
| LAM oaIfFrequencyMin | 1.3.6.1.4.1.8708.2.19.2.2.1.1.16 | LambdaFrequency | read-write | Lowest amplified freqency in hundreds of GHz (0.01 GHz). Supported range 19210 ... 19590 (c921 .. c959) |
| LAM oaIfFrequencyMax | 1.3.6.1.4.1.8708.2.19.2.2.1.1.17 | LambdaFrequency | read-write | Highest amplified freqency in hundreds of GHz (0.01 GHz). Supported range 19210 ... 19590 (c921 .. c959) |
| I32 oaIfNominalTxPower | 1.3.6.1.4.1.8708.2.19.2.2.1.1.18 | Integer32 | read-only | The production setting for output power in units of 0.1 dBm. |
| I32 oaIfTxPowerLevel | 1.3.6.1.4.1.8708.2.19.2.2.1.1.19 | Integer32 | read-only | The transmitted power level in units of 0.1 dBm. |
| I32 oaIfRxPowerLevel | 1.3.6.1.4.1.8708.2.19.2.2.1.1.20 | Integer32 | read-only | The received power level in units of 0.1 dBm. |
| I32 oaIfRxPowerLevelLowThreshold | 1.3.6.1.4.1.8708.2.19.2.2.1.1.21 | Integer32 | read-write | The lower threshold for received power level relative to the loss of signal threshold, in units of 0.1 dB. |
| U32 oaIfLaserBias | 1.3.6.1.4.1.8708.2.19.2.2.1.1.22 | Unsigned32 | read-only | Measures laser bias current value in tenths of mA (0.1 mA). |
| U32 oaIfNominalLaserTemp | 1.3.6.1.4.1.8708.2.19.2.2.1.1.23 | Unsigned32 | read-only | The pre-set laser temperature (0.1 deg C) |
| I32 oaIfRelativeLaserTemp | 1.3.6.1.4.1.8708.2.19.2.2.1.1.24 | Integer32 | read-only | The current offset from the pre-set temperature in units of 0.1 degrees centigrade. |
| I32 oaIfLossOfSignalThreshold | 1.3.6.1.4.1.8708.2.19.2.2.1.1.25 | Integer32 | read-write | The threshold for loss of signal. Note: Depending on the type of optical amplifier the value range may vary. |
| FAU oaIfLossOfSignal | 1.3.6.1.4.1.8708.2.19.2.2.1.1.26 | FaultStatus | read-only | Loss of signal. Applicable for all signal formats. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW indication. |
| FAU oaIfPumpLaserTempHigh | 1.3.6.1.4.1.8708.2.19.2.2.1.1.27 | FaultStatus | read-only | Pump laser temperature too high. A(ctivation): Temperature exceedes threshold. D(e-activation): Temperature below threshold again. |
| FAU oaIfRegulationProblemRxPowerHigh | 1.3.6.1.4.1.8708.2.19.2.2.1.1.28 | FaultStatus | read-only | The input power is above meassuring range. A: The received power level exceeds the associated threshold. D: The received power level is 0.5 dBm below the threshold. |
| FAU oaIfRegulationProblemTxPowerHigh | 1.3.6.1.4.1.8708.2.19.2.2.1.1.29 | FaultStatus | read-only | The output power is above meassuring range. A: The received power level exceeds the associated threshold. D: The received power level is 0.5 dBm below the threshold. |
| FAU oaIfRegulationProblemTxPowerLow | 1.3.6.1.4.1.8708.2.19.2.2.1.1.30 | FaultStatus | read-only | The output power is below meassuring range. A: The transmitted power level below the associated threshold. D: The transmitted power level is 0.5 dBm above the threshold. |
| FAU oaIfReceivedPowerLow | 1.3.6.1.4.1.8708.2.19.2.2.1.1.31 | FaultStatus | read-only | Received power level low threshold exceeded. A: The received power level is below the associated threshold. D: The received power level is 0.5 dBm above the threshold. |
| FAU oaIfLaserBiasHigh | 1.3.6.1.4.1.8708.2.19.2.2.1.1.32 | FaultStatus | read-only | Laser bias high threshold exceeded. A: The laser bias current exceeds the associated threshold. D: The laser bias current is 0.5 mA below the associated threshold. |
| FAU oaIfLaserTempControlFault | 1.3.6.1.4.1.8708.2.19.2.2.1.1.33 | FaultStatus | read-only | The pump laser temperature exceeds the associated threshold. A: The temperature exceeds the value. D: The temperature is below the value. |
| FAU oaIfHwMissing | 1.3.6.1.4.1.8708.2.19.2.2.1.1.34 | FaultStatus | read-only | The HW for this i/f is not present A: Wrong HW is inserted in subrack. D: Correct HW is inserted in subrack. |
| STR oaIfConfigurationCommand | 1.3.6.1.4.1.8708.2.19.2.2.1.1.35 | CommandString | read-only | Select which amplifier type to use. All modes are not applicable for all type of amplifier boards. constantGain: Amplifier will set output power according to the input power and the given gain constantSignalPower: Amplifier will set a constant output power with noise-compensation constantPower: Amplifier will set a constant output power independent of input power constantGainLI: Amplifier will work with constant gain in the low input power region (-35 to -5 dBm) constantGainHI: Amplifier will work with constant gain in the high input power region (-25 to +8 dBm) pow10: Power amplifier for 10G pre10ad: Pre-amplifier for 10G in add/drop config. pre25ad: Pre-amplifier for 2.5G in add/drop config. pre10tm: Pre-amplifier for 10G in TM configuration pre25tm: Pre-amplifier for 2.5G in TM configuration |
| FAU oaIfPumpLaserTempLow | 1.3.6.1.4.1.8708.2.19.2.2.1.1.36 | FaultStatus | read-only | Pump laser temperature too low. A(ctivation): Temperature exceedes threshold. D(e-activation): Temperature above threshold again. |
| I32 oaIfLaserTempLowRelativeThreshold | 1.3.6.1.4.1.8708.2.19.2.2.1.1.37 | Integer32 | read-write | Threshold for the Laser Temp Low alarm, expressed as an offset from a pre-set nominal temperature, in units of 0.1 degrees centigrade. |
| I32 oaIfLaserTempHighRelativeThreshold | 1.3.6.1.4.1.8708.2.19.2.2.1.1.38 | Integer32 | read-write | Threshold for the Laser Temp High alarm, expressed as an offset from a pre-set nominal temperature, in units of 0.1 degrees centigrade. |
| FAU oaIfAmpTypeNotSupportedByHw | 1.3.6.1.4.1.8708.2.19.2.2.1.1.39 | FaultStatus | read-only | The HW revision does not support the selected amplifier type. |
| I32 oaIfWantedSignalPowerLevel | 1.3.6.1.4.1.8708.2.19.2.2.1.1.40 | Integer32 | read-write | Wanted offset from production setting in units of 0.1 dBm. Applicable for preAmp25GAd and preAmp10GAd. Note that the output power level is dependent on the power of the input signal, so you might not always get the power that you want. |
| OBJ oaIfObjectProperty | 1.3.6.1.4.1.8708.2.19.2.2.1.1.41 | ObjectProperty | read-only | Property mask. |
| INT oaIfLaserForcedOn | 1.3.6.1.4.1.8708.2.19.2.2.1.1.42 | INTEGER | read-write | When enabled, the laser control is on regardless of whether there is an input signal present or not. disabled - the laser control is activated first after input signal is detected enabled - the laser control is always on |
| I32 oaIfActualLaserTemp | 1.3.6.1.4.1.8708.2.19.2.2.1.1.43 | Integer32 | read-only | The current laser temperature in units of 0.1 degrees centigrade. |
| INT oaIfAutomaticPowerShutdown | 1.3.6.1.4.1.8708.2.19.2.2.1.1.44 | INTEGER | read-write | When enabled, the laser is turned off if the input signal to the other gain block is lost. disabled - the laser is NOT affected by the other gain block. enabled - the laser is turned off if the input to the other gain block is lost. |
| FAU oaIfDisabled | 1.3.6.1.4.1.8708.2.19.2.2.1.1.45 | FaultStatus | read-only | The interface is disabled. A: Interface disabled. D: Interface enabled. |
| I32 oaIfWantedPowerLimit | 1.3.6.1.4.1.8708.2.19.2.2.1.1.46 | Integer32 | read-write | Applicable for constantGainLI/HI. Sets the maximum allowed output power. This attribute can be written via SNMP. |
| STR oaIfModuleInfo | 1.3.6.1.4.1.8708.2.19.2.2.1.1.47 | DisplayString | read-only | Information (for example firmware and serial number) about the module. |
| STR oaIfMonitorInsertionLoss | 1.3.6.1.4.1.8708.2.19.2.2.1.1.48 | DisplayString | read-only | The insertion loss for the monitor port. When the real insertion loss is not possible to read from unit (older HW revsions), 20 (default) dB will be shown which is the normal value. |
| U32 oaIfNumMonitorInsertionLoss | 1.3.6.1.4.1.8708.2.19.2.2.1.1.49 | Unsigned32 | read-only | This is the same parameter as Monitor Port Insertion Loss. The difference is that you will not see if the value can be read from the port or not (if not 20 dB will be shown). |
| INT oaIfFunctionalType | 1.3.6.1.4.1.8708.2.19.2.2.1.1.50 | INTEGER | read-write | The functional type of amplifier. This attribute is ONLY used by TNM and the traffic is not affected if changed. undefined - default preAmp - pre-amplifier. Receiving amplifier on a terminal node. offLinePreAmp - offline pre-amplifier. Receiving amplifier in a non-terminal node. Offline pre-amplifier amplifies dropped traffic, NOT line traffic. lineAmp - line amplifier. Amplifier situated between the terminal nodes, which amplifies passing line traffic and (if applicable) added traffic. booster - booster. The transmitting amplifier from a terminal node. |
| I32 oaIfActualGain | 1.3.6.1.4.1.8708.2.19.2.2.1.1.51 | Integer32 | read-only | Actual measured gain in units of 0.1 dB. |
| FAU oaIfSaturationFault | 1.3.6.1.4.1.8708.2.19.2.2.1.1.52 | FaultStatus | read-only | Saturation alarm threshold is passed. Actual Gain < (Wanted Gain -1 dB). The alarm can be cleared be cleared by reducing the wanted gain attribute. |
| I32 oaIfWantedGainTilt | 1.3.6.1.4.1.8708.2.19.2.2.1.1.53 | Integer32 | read-write | Settable gain tilt for variable gain OA in units of 0.1 dB. Positive gain tilt is defined as gain increasing wavelength. Negative gain tilt is defined as gain decreasing wavelength. |
| I32 oaIfTxPowerLevelLowThreshold | 1.3.6.1.4.1.8708.2.19.2.2.1.1.54 | Integer32 | read-write | The lower threshold for transmitted power level transmits to the loss of signal threshold, in units of 0.1 dB. |
| U32 oaIfLaserPumpBias | 1.3.6.1.4.1.8708.2.19.2.2.1.1.55 | Unsigned32 | read-only | Measures laser pump bias current in per cent (%) of max value. |
| FAU oaIfCaseTempOutOfrange | 1.3.6.1.4.1.8708.2.19.2.2.1.1.56 | FaultStatus | read-only | The module has shutdown automatically because of too high case temp (>85 degC) or too low case temp (-40 degC). A(ctivation): Case temperature exceedes pre-set temp range. D(e-activation): Case temperature within pre-set temp range again. |
| FAU oaIfLaserTempOutOfRange | 1.3.6.1.4.1.8708.2.19.2.2.1.1.57 | FaultStatus | read-only | the module has shutdown automatically because of pump laser temp out of range (15-35 degC). A(ctivation): Laser temperature exceedes pre-set value. D(e-activation): Laser temperature below pre-set value again. |
| T/F oaIfSupportsReadMonitorInsertionLoss | 1.3.6.1.4.1.8708.2.19.2.2.1.1.58 | TruthValue | read-only | This value tells whether a OA interface has the ability to read the insertion loss value for the monitor port on an interface. true: Insertion loss can be read for this interface false: Insertion loss cannot be read for this interface |
| INT oaIfTxSignalStatus | 1.3.6.1.4.1.8708.2.19.2.2.1.1.59 | INTEGER | read-only | The operational state for outgoing (TX) signal of the interface. down - A fault that would lead to a protection switch has occurred. degraded - The signal quality is impaired. up - The signal is OK. notApplicable (2147483647) - Attribute is not used on board. |
| INT oaIfRxSignalStatus | 1.3.6.1.4.1.8708.2.19.2.2.1.1.60 | INTEGER | read-only | The operational state for incoming (RX) signal of the interface. down - A major fault has occurred degraded - The signal quality is impaired. up - The signal is OK. notApplicable (2147483647) - Attribute is not used on board |
| FAU oaIfOutputPowerFail | 1.3.6.1.4.1.8708.2.19.2.2.1.1.61 | FaultStatus | read-only | Output power failed alarm threshold is passed. Actual Gain < (Wanted Gain -1 dB) and Output Power < (Power Limit -1 dB). |
| lumentisOaNotifications | 1.3.6.1.4.1.8708.2.19.2.3 | |||
| oaVoaIfList | 1.3.6.1.4.1.8708.2.19.2.4 | |||
| oaVoaIfTable | 1.3.6.1.4.1.8708.2.19.2.4.1 | not-accessible | The interface list. | |
| oaVoaIfEntry | 1.3.6.1.4.1.8708.2.19.2.4.1.1 | not-accessible | An entry in the interface list. | |
| U32 oaVoaIfIndex | 1.3.6.1.4.1.8708.2.19.2.4.1.1.1 | Unsigned32 | read-only | An arbitrary index assigned to each entry. |
| STR oaVoaIfName | 1.3.6.1.4.1.8708.2.19.2.4.1.1.2 | MgmtNameString | read-only | The management name of the interface, for example 'voa:1:2:1'. |
| STR oaVoaIfDescr | 1.3.6.1.4.1.8708.2.19.2.4.1.1.3 | DisplayString | read-write | User configurable label. |
| SUB oaVoaIfSubrack | 1.3.6.1.4.1.8708.2.19.2.4.1.1.4 | SubrackNumber | read-only | The number of the subrack where the interface is located. |
| SLO oaVoaIfSlot | 1.3.6.1.4.1.8708.2.19.2.4.1.1.5 | SlotNumber | read-only | The number of the slot where the interface is located. |
| POR oaVoaIfTxPort | 1.3.6.1.4.1.8708.2.19.2.4.1.1.6 | PortNumber | read-only | The number of the port where the TX part of the interface is located. |
| POR oaVoaIfRxPort | 1.3.6.1.4.1.8708.2.19.2.4.1.1.7 | PortNumber | read-only | The number of the port where the RX part of the interface is located. |
| U32 oaVoaIfInvPhysIndexOrZero | 1.3.6.1.4.1.8708.2.19.2.4.1.1.8 | Unsigned32 | read-only | The row in the invPhysTable for this interface. Set to 0 if not known. |
| NUM oaVoaIfAdminStatus | 1.3.6.1.4.1.8708.2.19.2.4.1.1.9 | BoardOrInterfaceAdminStatus | read-write | The administrative state for the interface. down - The interface should be inactive. service - The interface is activated but alarms are suppressed. Intended for use during service or re-configuration. When service is concluded adminStatus should be set to 'up' again. Note that there is no difference between 'up' and 'service', if no alarms can be rasied from this object. up - The interface should be activated when it becomes available. Alarms are not suppressed. This attribute can be written via SNMP. |
| NUM oaVoaIfOperStatus | 1.3.6.1.4.1.8708.2.19.2.4.1.1.10 | BoardOrInterfaceOperStatus | read-only | The operational state for the interface. notPresent - The interface is not available. down - The interface is not used. up - The interface is active. |
| OBJ oaVoaIfObjectProperty | 1.3.6.1.4.1.8708.2.19.2.4.1.1.11 | ObjectProperty | read-only | Property mask. |
| INT oaVoaIfControlMode | 1.3.6.1.4.1.8708.2.19.2.4.1.1.12 | INTEGER | read-create | The control mode of the VOA channel. constPower - regulate slowly towards a given output power. constAttenuation - set a fix attenuation constPowerAtInstallation - like constPower but allow faster changes (this mode is not released) |
| I32 oaVoaIfWantedOutputPower | 1.3.6.1.4.1.8708.2.19.2.4.1.1.13 | Integer32 | read-write | The wanted output power. Applicable for constPower. |
| I32 oaVoaIfCurrentOutputPower | 1.3.6.1.4.1.8708.2.19.2.4.1.1.14 | Integer32 | read-only | The actual output power. |
| U32 oaVoaIfRegulationRange | 1.3.6.1.4.1.8708.2.19.2.4.1.1.15 | Unsigned32 | read-write | An offset below the wanted output power at which the 'Current Power Out Of Range' alarm shall be raised. When the current output power is so far below the wanted output power, the regulation stops and the alarm is raised. Applicable for constPower. |
| U32 oaVoaIfWantedAttenuation | 1.3.6.1.4.1.8708.2.19.2.4.1.1.16 | Unsigned32 | read-write | The wanted attenuation. voa8ch: applicable for constAttenuation voa2ch: always applicable This attribute can be written via SNMP. |
| U32 oaVoaIfCurrentAttenuation | 1.3.6.1.4.1.8708.2.19.2.4.1.1.17 | Unsigned32 | read-only | The current attenuation. Applicable for constPower. |
| U32 oaVoaIfSamplePeriod | 1.3.6.1.4.1.8708.2.19.2.4.1.1.18 | Unsigned32 | read-only | The approximate period between 2 consecutive measurements of the output power |
| FAU oaVoaIfOuputPowerControlFailure | 1.3.6.1.4.1.8708.2.19.2.4.1.1.19 | FaultStatus | read-only | Alarm raised when the wanted output power can not be obtained. That is, even if the attenuation is reduced to zero, the wanted power can not be obtained. |
| FAU oaVoaIfCurrentPowerOutOfRange | 1.3.6.1.4.1.8708.2.19.2.4.1.1.20 | FaultStatus | read-only | Alarm raised when the current output power is outside the 'regulation range'. The regulation range is defined by Wanted Output Power +/- Regulation Range At this point, no regulation will be performed. The operator must change the wantedOutputPower. |
| STR oaVoaIfConfigurationCommand | 1.3.6.1.4.1.8708.2.19.2.4.1.1.21 | CommandString | read-only | Select which control mode to use: constPower constAttenuation |
| FAU oaVoaIfInInstallationMode | 1.3.6.1.4.1.8708.2.19.2.4.1.1.22 | FaultStatus | read-only | Alarm raised when the VOA is put in the mode constPowerAtInstallation. |
| oaVoaClientIfList | 1.3.6.1.4.1.8708.2.19.2.5 | |||
| oaVoaClientIfTable | 1.3.6.1.4.1.8708.2.19.2.5.1 | not-accessible | The interface list. | |
| oaVoaClientIfEntry | 1.3.6.1.4.1.8708.2.19.2.5.1.1 | not-accessible | An entry in the interface list. | |
| U32 oaVoaClientIfIndex | 1.3.6.1.4.1.8708.2.19.2.5.1.1.1 | Unsigned32 | read-only | An arbitrary index assigned to each entry. |
| STR oaVoaClientIfName | 1.3.6.1.4.1.8708.2.19.2.5.1.1.2 | MgmtNameString | read-only | The management name of the interface, for example 'voaClient:1:2:1' which indicates subrack 1, board 2 and port 1. |
| STR oaVoaClientIfDescr | 1.3.6.1.4.1.8708.2.19.2.5.1.1.3 | DisplayString | read-write | User configurable label. |
| SUB oaVoaClientIfSubrack | 1.3.6.1.4.1.8708.2.19.2.5.1.1.4 | SubrackNumber | read-only | The number of the subrack where the interface is located. |
| SLO oaVoaClientIfSlot | 1.3.6.1.4.1.8708.2.19.2.5.1.1.5 | SlotNumber | read-only | The number of the slot where the interface is located. |
| POR oaVoaClientIfTxPort | 1.3.6.1.4.1.8708.2.19.2.5.1.1.6 | PortNumber | read-only | The number of the port where the Tx part of the interface is located. |
| POR oaVoaClientIfRxPort | 1.3.6.1.4.1.8708.2.19.2.5.1.1.7 | PortNumber | read-only | The number of the port where the Rx part of the interface is located. |
| U32 oaVoaClientIfInvPhysIndexOrZero | 1.3.6.1.4.1.8708.2.19.2.5.1.1.8 | Unsigned32 | read-only | The row in the invPhysTable for this interface. Set to 0 if not known. |
| NUM oaVoaClientIfAdminStatus | 1.3.6.1.4.1.8708.2.19.2.5.1.1.9 | BoardOrInterfaceAdminStatus | read-write | The administrative state for the interface. down - The interface should be inactive. service - The interface is activated but alarms are suppressed. Intended for use during service or re-configuration. When service is concluded adminStatus should be set to 'up' again. up - The interface should be activated when it becomes available. Alarms are not suppressed. |
| NUM oaVoaClientIfOperStatus | 1.3.6.1.4.1.8708.2.19.2.5.1.1.10 | BoardOrInterfaceOperStatus | read-only | The operational state for the interface. notPresent - The interface is not available. down - The interface is not used. up - The interface is active. |
| OBJ oaVoaClientIfObjectProperty | 1.3.6.1.4.1.8708.2.19.2.5.1.1.11 | ObjectProperty | read-only | Property mask. |
| INT oaVoaClientIfControlMode | 1.3.6.1.4.1.8708.2.19.2.5.1.1.12 | INTEGER | read-create | The control mode of the VOA channel. constAttenuation - set a fix attenuation |
| U32 oaVoaClientIfWantedAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.13 | Unsigned32 | read-write | The wanted attenuation. Applicable for constAttenuation This attribute can be written via SNMP if not set to 2147483647. |
| U32 oaVoaClientIfCurrentAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.14 | Unsigned32 | read-only | The current attenuation. Applicable in case of MDU40 boards. |
| LAM oaVoaClientIfLambda | 1.3.6.1.4.1.8708.2.19.2.5.1.1.15 | LambdaFrequency | read-only | The frequency given in hundreds of GHz (0.01 GHz). Set to 0 for transparent ports. |
| U32 oaVoaClientIfAbsoluteAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.16 | Unsigned32 | read-write | The wanted absolute attenuation including the insertion loss. This value can never be set below the upper limit of the insertion loss. VOA8CHSFP: The range is dependent on the inserted VOA SFP. This attribute can be written via SNMP. |
| U32 oaVoaClientIfVoa2CurrentAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.17 | Unsigned32 | read-only | This value shows the current set absolute attenua- tion on VOA8ch-II and voa8chsfp. This value is usually the same value as the absolute attenuation except when a decrase or increase of attenuation is ongoing or when administrative status is set to down. |
| U32 oaVoaClientIfDecreaseAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.18 | Unsigned32 | read-write | The wanted decrease of the current attenuation. This attribute can be written via SNMP. |
| U32 oaVoaClientIfIncreaseAttenuation | 1.3.6.1.4.1.8708.2.19.2.5.1.1.19 | Unsigned32 | read-write | The wanted increase of the current attenuation. This attribute can be written via SNMP. |
| U32 oaVoaClientIfInsertionLoss | 1.3.6.1.4.1.8708.2.19.2.5.1.1.20 | Unsigned32 | read-only | The insertion loss for the port. The attenuation can never be set to a value below this value. |
| LAM oaVoaClientIfExpectedFrequency | 1.3.6.1.4.1.8708.2.19.2.5.1.1.21 | LambdaFrequency | read-write | The frequency given in hundreds of GHz (0.01 GHz). This value is only used for presentation purposes in name of port. |
| FAU oaVoaClientIfSfpMissing | 1.3.6.1.4.1.8708.2.19.2.5.1.1.22 | FaultStatus | read-only | An expected VOA SFP is missing. A(ctivation): An expected SFP is missing. D(e-activation): The missing SFP is inserted. |
| STR oaVoaClientIfSfpClass | 1.3.6.1.4.1.8708.2.19.2.5.1.1.23 | DisplayString | read-only | String that contains general information about the SFP. |
| FAU oaVoaClientIfSfpTransmitterFailed | 1.3.6.1.4.1.8708.2.19.2.5.1.1.24 | FaultStatus | read-only | The SFP has detected a failure in the transmitter part. A(ctivation): The transmitter has failed D(e-activation): The transmitter is OK again |
| FAU oaVoaClientIfSfpMediaMismatch | 1.3.6.1.4.1.8708.2.19.2.5.1.1.25 | FaultStatus | read-only | The type of the inserted SFP is not the expected one. A(ctivation): Invalid or mismatching SFP media is detected. D(e-activation): The correct SFP is used. |
| FAU oaVoaClientIfLossOfSignal | 1.3.6.1.4.1.8708.2.19.2.5.1.1.26 | FaultStatus | read-only | Loss of signal. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW indication. |
| FAU oaVoaClientIfSfpCodeMismatch | 1.3.6.1.4.1.8708.2.19.2.5.1.1.27 | FaultStatus | read-only | The inserted SFP does not have a legal manufacturer code. A(ctivation): A SFP with illegal code is inserted. D(e-activation): The SFP with illegal code is removed. |
| FAU oaVoaClientIfAttenuationConfigMismatch | 1.3.6.1.4.1.8708.2.19.2.5.1.1.28 | FaultStatus | read-only | The wanted attenuation is not supported by the inserted SFP. |
| oaVoaLineIfList | 1.3.6.1.4.1.8708.2.19.2.6 | |||
| oaVoaLineIfTable | 1.3.6.1.4.1.8708.2.19.2.6.1 | not-accessible | The interface list. | |
| oaVoaLineIfEntry | 1.3.6.1.4.1.8708.2.19.2.6.1.1 | not-accessible | An entry in the interface list. | |
| U32 oaVoaLineIfIndex | 1.3.6.1.4.1.8708.2.19.2.6.1.1.1 | Unsigned32 | read-only | An arbitrary index assigned to each entry. |
| STR oaVoaLineIfName | 1.3.6.1.4.1.8708.2.19.2.6.1.1.2 | MgmtNameString | read-only | The management name of the interface, for example 'VoaLine:1:2:1-2', where the first number indicates sub-rack, the second slot number and the third is the port number. Examples: oaVoaLine:s:s:p - line interface |
| STR oaVoaLineIfDescr | 1.3.6.1.4.1.8708.2.19.2.6.1.1.3 | DisplayString | read-write | User configurable label. This attribute can be written via SNMP. |
| SUB oaVoaLineIfSubrack | 1.3.6.1.4.1.8708.2.19.2.6.1.1.4 | SubrackNumber | read-create | The number of the subrack where the interface is located. |
| SLO oaVoaLineIfSlot | 1.3.6.1.4.1.8708.2.19.2.6.1.1.5 | SlotNumber | read-create | The number of the slot where the interface is located. |
| POR oaVoaLineIfTxPort | 1.3.6.1.4.1.8708.2.19.2.6.1.1.6 | PortNumber | read-create | The number of the port where the TX-side of the interface is located. |
| POR oaVoaLineIfRxPort | 1.3.6.1.4.1.8708.2.19.2.6.1.1.7 | PortNumber | read-create | The number of the port where the RX-side of the interface is located. |
| U32 oaVoaLineIfInvPhysIndexOrZero | 1.3.6.1.4.1.8708.2.19.2.6.1.1.8 | Unsigned32 | read-only | The row in the invPhysTable for this interface. Set to 0 if not known. |
| NUM oaVoaLineIfAdminStatus | 1.3.6.1.4.1.8708.2.19.2.6.1.1.9 | BoardOrInterfaceAdminStatus | read-write | The administrative state for the interface. down - The interface should be inactive. service - The interface is activated but alarms are suppressed. Intended for use during service or re-configuration. When service is concluded adminStatus should be set to 'up' again. up - The interface should be activated when it becomes available. Alarms are not suppressed. |
| NUM oaVoaLineIfOperStatus | 1.3.6.1.4.1.8708.2.19.2.6.1.1.10 | BoardOrInterfaceOperStatus | read-only | The operational state for the interface. notPresent - The interface is not available. down - The interface is not used. up - The interface is active. |
| FAU oaVoaLineIfModuleFailure | 1.3.6.1.4.1.8708.2.19.2.6.1.1.11 | FaultStatus | read-only | The module HW has detected a failure. A: The module has failed D: The module is OK again |
| OBJ oaVoaLineIfObjectProperty | 1.3.6.1.4.1.8708.2.19.2.6.1.1.12 | ObjectProperty | read-only | Property mask. |
| oaModuleList | 1.3.6.1.4.1.8708.2.19.2.7 | |||
| oaModuleTable | 1.3.6.1.4.1.8708.2.19.2.7.1 | not-accessible | The module list. | |
| oaModuleEntry | 1.3.6.1.4.1.8708.2.19.2.7.1.1 | not-accessible | An entry in the module list. | |
| U32 oaModuleIndex | 1.3.6.1.4.1.8708.2.19.2.7.1.1.1 | Unsigned32 | read-only | An arbitrary index assigned to each entry. |
| STR oaModuleName | 1.3.6.1.4.1.8708.2.19.2.7.1.1.2 | MgmtNameString | read-only | The management name of the interface, for example 'module:1:2:1'. |
| STR oaModuleDescr | 1.3.6.1.4.1.8708.2.19.2.7.1.1.3 | DisplayString | read-write | User configurable label. |
| SUB oaModuleSubrack | 1.3.6.1.4.1.8708.2.19.2.7.1.1.4 | SubrackNumber | read-only | The number of the subrack where the module is located. |
| SLO oaModuleSlot | 1.3.6.1.4.1.8708.2.19.2.7.1.1.5 | SlotNumber | read-only | The number of the slot where the module is located. |
| POR oaModuleNumber | 1.3.6.1.4.1.8708.2.19.2.7.1.1.6 | PortNumber | read-only | The number of the module on the board. |
| U32 oaModuleInvPhysIndexOrZero | 1.3.6.1.4.1.8708.2.19.2.7.1.1.7 | Unsigned32 | read-only | The row in the invPhysTable for this interface. Set to 0 if not known. |
| NUM oaModuleAdminStatus | 1.3.6.1.4.1.8708.2.19.2.7.1.1.8 | BoardOrInterfaceAdminStatus | read-write | The administrative state for the module. up - Alarms are not suppressed. service - Alarms from the module are suppressed. The module is still activated. down - Currently not used. |
| NUM oaModuleOperStatus | 1.3.6.1.4.1.8708.2.19.2.7.1.1.9 | BoardOrInterfaceOperStatus | read-only | The operational state for the module. notPresent - The module is not available. down - The module is not used. up - The module is active. |
| OBJ oaModuleObjectProperty | 1.3.6.1.4.1.8708.2.19.2.7.1.1.10 | ObjectProperty | read-only | Property mask. |
| I32 oaModuleNominalTemp | 1.3.6.1.4.1.8708.2.19.2.7.1.1.11 | Integer32 | read-only | The set temperature in units of 0.1 degrees centigrade. |
| I32 oaModuleRelativeTemp | 1.3.6.1.4.1.8708.2.19.2.7.1.1.12 | Integer32 | read-only | The relative temperature in units of 0.1 degrees centigrade. |
| FAU oaModuleTempFailure | 1.3.6.1.4.1.8708.2.19.2.7.1.1.13 | FaultStatus | read-only | The module temperature is above/below expected one. A: The temperature is not correct. D: The temperature becomes correct. |
| I32 oaModuleTemperature | 1.3.6.1.4.1.8708.2.19.2.7.1.1.14 | Integer32 | read-only | The temperature of the module in 0.1 degrees centigrade |
| FAU oaModuleCommunicationFailure | 1.3.6.1.4.1.8708.2.19.2.7.1.1.15 | FaultStatus | read-only | The communication with the module failed. A(ctivation): Failed to talk to the module D(e-activation): Could talk to the module again |
| STR oaModuleModuleInfo | 1.3.6.1.4.1.8708.2.19.2.7.1.1.16 | DisplayString | read-only | Information (for example firmware and serial number) about the module. |
| FAU oaModuleVcomThresholdExceeded | 1.3.6.1.4.1.8708.2.19.2.7.1.1.17 | FaultStatus | read-only | The common voltage supply in the ROADM module has exceeded recommended threshold. Firmware upgrade is recommended to resolve this alarm. A(ctivation): The VCOM threshold is exceeded D(e-activation): The VCOM threshold is OK again |
| FAU oaModuleFirmwareUpgradeAvailable | 1.3.6.1.4.1.8708.2.19.2.7.1.1.18 | FaultStatus | read-only | An upgrade is available for the ROADM module. See release notes for details on how to obtain and install the upgrade |
| FAU oaModuleWarmingUp | 1.3.6.1.4.1.8708.2.19.2.7.1.1.19 | FaultStatus | read-only | ROADM module is warming up, the optics has not reached a stable temperature, all channels are blocked. A(ctivation): cold start of ROADM board D(e-activation): the warning is cleared as soon as the module has reached a stable temperature, this takes 3-8 minutes |
| FAU oaModuleFailure | 1.3.6.1.4.1.8708.2.19.2.7.1.1.20 | FaultStatus | read-only | The module HW has detected a failure. A(ctivation): The module has failed D(e-activation): The module is OK again |
RFC description
ADTRAN LUM (Lightwire Unit Manager) MIB for managing optical amplifier characteristics and performance.
Start monitoring Infinera DWDM optical amplifier module with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.