All MIBs › INTEL-VLAN-MIB
Category: Technology: VLAN, VLAN and Bridging, Vendor: Intel
Description: Intel VLAN MIB providing SNMP objects for 802.1Q virtual LAN configuration and port membership on Intel switching products.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is INTEL-VLAN-MIB?
INTEL-VLAN-MIB is a vendor-specific MIB providing 802.1Q VLAN configuration and port-membership management for Intel switching products. It is expected to expose VLAN ID assignment and port-to-VLAN membership tables typical of switch VLAN MIBs. Its monitoring focus is software/configuration state - confirming which ports belong to which VLANs and whether ports are tagged or untagged - rather than physical hardware sensors, making it useful for verifying that VLAN segmentation policy is applied as intended. It builds conceptually on the IEEE 802.1Q standard and likely relies on IF-MIB-style port indexing to map VLAN membership to physical ports. It is deployed on Intel Ethernet switches in enterprise LANs that use VLAN segmentation for traffic isolation. Network engineers evaluating or troubleshooting this functionality can download the INTEL-VLAN-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in INTEL-VLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Intel Ethernet switch
Monitoring Examples
Following the standard Intel switch VLAN MIB pattern, an admin would poll a VLAN membership table to confirm a given switch port is tagged or untagged into the expected VLAN ID, catching a misconfigured port that inadvertently bridges traffic between VLANs that should remain isolated.
What Can Be Monitored
- VLAN ID assignment
- port VLAN membership
- tagged/untagged port mode
- VLAN configuration table
This MIB depends on
Related MIBs
Imported Objects
From INTEL-GEN-MIB
| mib2ext | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| sysName |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| vlan | 1.3.6.1.4.1.343.6.11 | |||
| NTF globalVlanConfigurationChange | 1.3.6.1.4.1.343.6.11.0.1 | A new VLAN configuration has been distributed. | ||
| NTF localConfigurationChange | 1.3.6.1.4.1.343.6.11.0.2 | Changes made to local VLAN configuration. | ||
| NTF invalidVlanConfiguration | 1.3.6.1.4.1.343.6.11.0.3 | Error in uploaded configuration. | ||
| NTF domainNameChange | 1.3.6.1.4.1.343.6.11.0.5 | The VLAN domain name has been changed. | ||
| NTF newSwitchInDomain | 1.3.6.1.4.1.343.6.11.0.6 | This station is now participating in the domain. | ||
| NTF missingSwitchInDomain | 1.3.6.1.4.1.343.6.11.0.7 | A switch is no longer in the domain. | ||
| NTF editTokenForceRelease | 1.3.6.1.4.1.343.6.11.0.8 | This station has made a forced release of the edit token for the VLAN configuration | ||
| NTF editTokenRequestFailed | 1.3.6.1.4.1.343.6.11.0.9 | A management station tried to allocate the token while it was not available. | ||
| NTF configConfirmFailed | 1.3.6.1.4.1.343.6.11.0.10 | The new configuration rendered the device inaccessible to the management station, and the old configuration has been restored. | ||
| NTF vlanLearnedDatabaseFull | 1.3.6.1.4.1.343.6.11.0.11 | The VLAN learning process was unable to insert an entry in the VLAN database. This may result in a loss of connectivity between some stations. This is not an error; the setup is larger than the system has been designed to handle. | ||
| vlanPolicy | 1.3.6.1.4.1.343.6.11.1 | |||
| STR vlanPolicyDomainName | 1.3.6.1.4.1.343.6.11.1.1 | DisplayString | read-write | The VLAN Domain name. All VLAN configuration and connectivity is separated in domains. |
| INT vlanPolicyServerSeqNo | 1.3.6.1.4.1.343.6.11.1.2 | INTEGER | read-only | The sequence number of the configuration policy of the VLAN sever. |
| INT vlanPolicyClientSeqNo | 1.3.6.1.4.1.343.6.11.1.3 | INTEGER | read-only | The sequence number of the configuration policy of the client. |
| INT vlanPolicyMode | 1.3.6.1.4.1.343.6.11.1.4 | INTEGER | read-write | The device is running VLAN in 1 of 2 possible modes. 1) Distributed VLAN - the configuration and VLAN memberships are shared with other devices in the same domain. 2) Stand-alone - the configuration has only local significance. When running the devices in a stack the values 3 or 4 will be returned according to the actual mode, but only the values 1 and 2 will be accepted for set-requests. For some devices this object can not be set to fullVlan. Refer to vlanPolicySupportedVlanModes object. |
| TIK vlanPolicyChangedStamp | 1.3.6.1.4.1.343.6.11.1.5 | TimeTicks | read-only | Local timestamp of last policy configuration change |
| INT vlanPolicyNextVlanId | 1.3.6.1.4.1.343.6.11.1.6 | INTEGER | read-only | Returns the next VLAN id to be used when creating a new VLAN |
| INT vlanPolicyLastApiError | 1.3.6.1.4.1.343.6.11.1.7 | INTEGER | read-only | Return code for the last occurred error when making changes to the VLAN database |
| INT vlanPolicyChangeOperation | 1.3.6.1.4.1.343.6.11.1.8 | INTEGER | read-write | This object must be set when changing the name of a VLAN DOMAIN, to indicate whether the change is a rename- or a create-operation |
| vlanPolicyVlanTable | 1.3.6.1.4.1.343.6.11.1.9 | not-accessible | Table of configured VLANs | |
| policyVlanEntry | 1.3.6.1.4.1.343.6.11.1.9.1 | not-accessible | Entry in VLAN table consists of id and name and contains two special binary objects for creating and deleting VLANs | |
| INT policyVlanId | 1.3.6.1.4.1.343.6.11.1.9.1.1 | INTEGER | read-only | The internal id number of a VLAN. Must be used as index for creating and deleting |
| STR policyVlanName | 1.3.6.1.4.1.343.6.11.1.9.1.2 | DisplayString | read-write | Name of the VLAN (20 bytes ASCII-Z string) |
| OCT policyVlanCreateObj | 1.3.6.1.4.1.343.6.11.1.9.1.3 | OCTET STRING | read-write | This object is used to create a new VLAN. The object takes parameters as binary-coded octet strings. Index (policyVlanId) used must be value from vlanPolicyNextVlanId. Binary format: [name (20 bytes ASCII-Z string)] |
| INT policyVlanDeleteObj | 1.3.6.1.4.1.343.6.11.1.9.1.4 | INTEGER | read-write | This object is used to delete an existing VLAN. The id of the VLAN must be used as index |
| vlanPolicyMacRuleTable | 1.3.6.1.4.1.343.6.11.1.10 | not-accessible | Table of configured MAC rules in a VLAN | |
| policyMacRuleEntry | 1.3.6.1.4.1.343.6.11.1.10.1 | not-accessible | Entry in MAC rule table consist of VLAN id and MAC address and contains two special binary objects for creating and deleting rules | |
| INT policyMacRuleVlanId | 1.3.6.1.4.1.343.6.11.1.10.1.1 | INTEGER | read-only | Id of VLAN. Used as index when creating and deleting a rule |
| ADR policyMacRuleAddress | 1.3.6.1.4.1.343.6.11.1.10.1.2 | EthMacAddress | read-only | MAC address string rule (6 bytes) for VLAN learning |
| OCT policyMacRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.10.1.3 | OCTET STRING | read-write | This object is used to create a new MAC rule. The object takes parameters as binary-coded octet strings. Index (policyMacRuleVlanId and policyMacRuleAddress) used must be an existing VLAN id and a valid 6 byte MAC address. Binary format: [] {= leave empty} |
| INT policyMacRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.10.1.4 | INTEGER | read-write | This object is used to delete an existing MAC rule. The VLAN id and MAC address of the rule must be used as index |
| vlanPolicyIslMacRuleTable | 1.3.6.1.4.1.343.6.11.1.11 | not-accessible | THIS TABLE HAS BEEN OBSOLETED! Table of configured IslMAC rules in a VLAN | |
| policyIslMacRuleEntry | 1.3.6.1.4.1.343.6.11.1.11.1 | not-accessible | THIS ENTRY HAS BEEN OBSOLETED! Entry in IslMAC rule table consists of VLAN id and IslMAC address and contains two special binary objects for creating and deleting rules | |
| INT policyIslMacRuleVlanId | 1.3.6.1.4.1.343.6.11.1.11.1.1 | INTEGER | read-only | OBJECT HAS BEEN OBSOLETED! Id of VLAN. Used as index when creating and deleting a rule |
| ADR policyIslMacRuleAddress | 1.3.6.1.4.1.343.6.11.1.11.1.2 | EthMacAddress | read-only | OBJECT HAS BEEN OBSOLETED! MAC address string rule (6 bytes) for VLAN learning |
| OCT policyIslMacRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.11.1.3 | OCTET STRING | read-write | OBJECT HAS BEEN OBSOLETED! This object is used to create a new IslMAC rule. The object takes parameters as binary-coded octet strings. Index (policyIslMacRuleVlanId and policyIslMacRuleAddress) used must be an existing VLAN id and a valid 6 byte MAC address. Binary format: [] {= leave empty} |
| INT policyIslMacRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.11.1.4 | INTEGER | read-write | OBJECT HAS BEEN OBSOLETED! This object is used to delete an existing IslMAC rule. The VLAN id and MAC address of the rule must be used as index |
| vlanPolicyIpRuleTable | 1.3.6.1.4.1.343.6.11.1.12 | not-accessible | Table of configured IP rules in a VLAN | |
| policyIpRuleEntry | 1.3.6.1.4.1.343.6.11.1.12.1 | not-accessible | Entry in IP rule table consists of VLAN id and IP address and contains two special binary objects for creating and deleting rules | |
| INT policyIpRuleVlanId | 1.3.6.1.4.1.343.6.11.1.12.1.1 | INTEGER | read-only | Id of VLAN. Used as index when creating and deleting a rule |
| IP policyIpRuleAddress | 1.3.6.1.4.1.343.6.11.1.12.1.2 | IpAddress | read-only | IP address string rule (4 bytes) for VLAN learning |
| OCT policyIpRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.12.1.3 | OCTET STRING | read-write | This object is used to create a new IP rule. The object takes parameters as binary-coded octet strings. Index (policyIpRuleVlanId and policyIpRuleAddress) used must be an existing VLAN id and a valid 4 byte IP address. Binary format: [] {= leave empty} |
| INT policyIpRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.12.1.4 | INTEGER | read-write | This object is used to delete an existing IP rule. The VLAN id and IP address of the rule must be used as index |
| vlanPolicyIpNetRuleTable | 1.3.6.1.4.1.343.6.11.1.13 | not-accessible | Table of configured IP Network rules in a VLAN | |
| policyIpNetRuleEntry | 1.3.6.1.4.1.343.6.11.1.13.1 | not-accessible | Entry in IP Network rule table consists of VLAN id, IP Network address and IP Network mask and contains two special binary objects for creating and deleting rules | |
| INT policyIpNetRuleVlanId | 1.3.6.1.4.1.343.6.11.1.13.1.1 | INTEGER | read-only | Id of VLAN. Used as index when creating and deleting a rule |
| IP policyIpNetRuleAddress | 1.3.6.1.4.1.343.6.11.1.13.1.2 | IpAddress | read-only | IP Network address string rule (4 bytes) for VLAN learning |
| IP policyIpNetRuleMask | 1.3.6.1.4.1.343.6.11.1.13.1.3 | IpAddress | read-only | IP Network subnet mask string (4 bytes). Rule will be the result of a bit-wise AND operation between address and mask |
| OCT policyIpNetRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.13.1.4 | OCTET STRING | read-write | This object is used to create a new IP Network rule. The object takes parameters as binary-coded octet strings. Index (policyIpNetRuleVlanId and policyIpNetRuleAddress) used must be an existing VLAN id and a valid 4 byte IP address. Binary format: [mask (4bytes)] |
| INT policyIpNetRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.13.1.5 | INTEGER | read-write | This object is used to delete an existing IP Network rule. The VLAN id and IP Network address of the rule must be used as index |
| vlanPolicyPortRuleTable | 1.3.6.1.4.1.343.6.11.1.14 | not-accessible | Table of configured Port rules in a VLAN | |
| policyPortRuleEntry | 1.3.6.1.4.1.343.6.11.1.14.1 | not-accessible | Entry in Port rule table consists of VLAN id and Port number and contains two special binary objects for creating and deleting rules | |
| INT policyPortRuleVlanId | 1.3.6.1.4.1.343.6.11.1.14.1.1 | INTEGER | read-only | Id of VLAN. Used as index when creating and deleting a rule |
| INT policyPortRuleNumber | 1.3.6.1.4.1.343.6.11.1.14.1.2 | INTEGER | read-only | Port number rule for VLAN learning |
| OCT policyPortRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.14.1.3 | OCTET STRING | read-write | This object is used to create a new Port rule. The object takes parameters as binary-coded octet strings. Index (policyPortRuleVlanId and policyPortRuleAddress) used must be an existing VLAN id and a valid 4 byte IP address. Binary format: [] {= leave empty} |
| INT policyPortRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.14.1.4 | INTEGER | read-write | This object is used to delete an existing Port rule. The VLAN id and Port number of the rule must be used as index |
| vlanPolicyPortSettingsTable | 1.3.6.1.4.1.343.6.11.1.15 | not-accessible | List of ports and their VLAN relevant configuration | |
| policyPortSettingsEntry | 1.3.6.1.4.1.343.6.11.1.15.1 | not-accessible | Entry consists of Port Number and state for IP learning on a port | |
| INT policyPortSettingsPortNumber | 1.3.6.1.4.1.343.6.11.1.15.1.1 | INTEGER | read-only | This is the Port number. Used as index when changing settings |
| INT policyPortSettingsIpLearning | 1.3.6.1.4.1.343.6.11.1.15.1.2 | INTEGER | read-write | This option enables or disables the IP rule learning on a per port basis. This option should be enabled for ports connected to IP traffic only networks |
| INT vlanPolicyAllPortSettingsIpLearning | 1.3.6.1.4.1.343.6.11.1.16 | INTEGER | read-write | This object is used to synchronize IP learning settings for all ports (set to either enabled or disabled). When read this object will also indicate if the settings are the same for all ports (enabled or disabled) or mixed |
| INT vlanPolicyAssignManagementVlan | 1.3.6.1.4.1.343.6.11.1.17 | INTEGER | read-write | Assign a VLAN to have access to the switch local management. NB: Only for desktop switches! |
| INT vlanPolicyConfigConfState | 1.3.6.1.4.1.343.6.11.1.18 | INTEGER | read-write | When a management center changes the VLAN configuration, there is a risk that it looses the access to the switch. Therefore, in case the switch is running VLAN in stand alone mode, a temporary backup of the old configuration is made. This copy is kept for 30 sec and if this object has not been set to confirm(5) within that time, the backup configuration is made active and the new modifications are lost (state will read revertedToOldConf(3)). When a Token is claimed the state is set to notReady(1) and the state cannot be set to confirm(5) until the state reads ready(2) (which means the configuration has been made active and the learning database updated). When setting state to confirm the backup is removed and the new configuration is made active, and the state reads confirmedNewConf(4). |
| INT vlanPolicyConfigConfTimerValue | 1.3.6.1.4.1.343.6.11.1.19 | INTEGER | read-only | This object returns the start value of the Configuration Confirm Timer |
| INT vlanPolicySupportedVlanModes | 1.3.6.1.4.1.343.6.11.1.20 | INTEGER | read-only | This object returns a bitmask containing the supported VLAN modes: 0x01 : Stand-alone VLAN 0x02 : Distributed VLAN |
| INT vlanPolicyRevert2Default | 1.3.6.1.4.1.343.6.11.1.21 | INTEGER | read-write | Setting this object to 1 will restore the original VLAN setup (1 System VLAN with all ports in it). NB: vlanMode and name is not effected by this! |
| INT vlanPolicyMacVlanServerPriority | 1.3.6.1.4.1.343.6.11.1.22 | INTEGER | read-write | This object sets the priority for this device to become MAC-VLAN server |
| INT vlanPolicyAutoMoveMgtIpLink | 1.3.6.1.4.1.343.6.11.1.23 | INTEGER | read-write | If this object is enabled, the switch will make use of the feature to let Main IP link follow the management VlanId. Otherwise Main IP link will not move with the management Vlan |
| vlanPolicyStackPortRuleTable | 1.3.6.1.4.1.343.6.11.1.24 | not-accessible | Table of configured Port rules in a VLAN for a stack | |
| policyStackPortRuleEntry | 1.3.6.1.4.1.343.6.11.1.24.1 | not-accessible | Entry in Stack Port rule table consists of VLAN id, Switch MAC and Port number and contains two special binary objects for creating and deleting rules | |
| INT policyStackPortRuleVlanId | 1.3.6.1.4.1.343.6.11.1.24.1.1 | INTEGER | read-only | Id of VLAN. Used as index when creating and deleting a rule |
| ADR policyStackPortRuleSwitchMac | 1.3.6.1.4.1.343.6.11.1.24.1.2 | EthMacAddress | read-only | Mac address identifying the switch on which the port is physically located |
| INT policyStackPortRuleNumber | 1.3.6.1.4.1.343.6.11.1.24.1.3 | INTEGER | read-only | Port number rule for VLAN learning |
| OCT policyStackPortRuleCreateObj | 1.3.6.1.4.1.343.6.11.1.24.1.4 | OCTET STRING | read-write | This object is used to create a new Stack Port rule. The object takes parameters as binary-coded octet strings. Index (policyStackPortRuleVlanId, policyStackPortRuleSwitchMac and policyStackPortRuleAddress) used must be an existing VLAN id, a valid MAC address present in the stack and a valid 4 byte IP address. Binary format: [] {= leave empty} |
| INT policyStackPortRuleDeleteObj | 1.3.6.1.4.1.343.6.11.1.24.1.5 | INTEGER | read-write | This object is used to delete an existing Port rule. The VLAN id, Switch Mac and Port number of the rule must be used as index |
| INT vlanPolicyUseMultiSTP | 1.3.6.1.4.1.343.6.11.1.25 | INTEGER | read-write | When enabled, the device will operate multiple spanning trees on top of VLANs. When disabled the device will operate with VLANs on top of a single spanning tree. |
| INT vlanPolicyFwdLearnPckts | 1.3.6.1.4.1.343.6.11.1.26 | INTEGER | read-write | Enable or Disable forwarding of learn-packets. A learn-packet is the packet that was used to learn a station the first time the switch received traffic from the station. If enabled these packets will be forwarded after learning is complete. If disabled these packets will be discarded after learning, to prevent packet re-ordering in the network. NB: This setting is not protected by the edit-token lock. |
| vlanLearned | 1.3.6.1.4.1.343.6.11.2 | |||
| INT vlanLearnedVersion | 1.3.6.1.4.1.343.6.11.2.1 | INTEGER | read-only | The version of the run-time database used for keeping actual VLAN information. |
| INT vlanLearnedServerState | 1.3.6.1.4.1.343.6.11.2.2 | INTEGER | read-only | State of the MAC-VLAN server: initActive - Initialising to become server initPassive - Initialising to become client passive - Station is client active - Station is server |
| INT vlanLearnedServerPriority | 1.3.6.1.4.1.343.6.11.2.3 | INTEGER | read-only | The priority of the server function. The lower the priority, the more likely that this device becomes the server. If there is a tie between the priorities the device with the lowest MAC will become server. |
| IP vlanLearnedServerIPAddress | 1.3.6.1.4.1.343.6.11.2.4 | IpAddress | read-only | The IP address of the current MAC-VLAN server |
| ADR vlanLearnedServerMACAddress | 1.3.6.1.4.1.343.6.11.2.5 | EthMacAddress | read-only | The MAC address of the current MAC-VLAN server |
| INT vlanLearnedServerPortNo | 1.3.6.1.4.1.343.6.11.2.6 | INTEGER | read-only | The port number through which the device is connected to the server. Only valid if device is client |
| INT vlanLearnedServerNameChangeTimer | 1.3.6.1.4.1.343.6.11.2.7 | INTEGER | read-write | Timer value used when renaming a VLAN DOMAIN. While timer is running, both the old and new Domain Name is accepted by all switches in the Domain. When renaming a Domain containing many switches, a high value of the timer may be needed to ensure that Domain is not 'broken'. Value is in seconds |
| INT vlanLearnedServerExpiryTimer | 1.3.6.1.4.1.343.6.11.2.8 | INTEGER | read-write | Time a device will wait before assuming the MAC-VLAN server is lost. If server is assumed lost, the device will search for a new server, or become the server itself. NOTE: The value used by all devices in a Domain, is the value configured on the device that currently is the MAC-VLAN server and NOT the individual settings on each device. |
| vlanLearnedMacTable | 1.3.6.1.4.1.343.6.11.2.9 | not-accessible | A list of all active stations in a VLAN in the domain for the device. | |
| learnedMacEntry | 1.3.6.1.4.1.343.6.11.2.9.1 | not-accessible | A VLAN active station. For each station there is information about its: MAC address. If possible additional information about on which access-port the station is placed, the protocol type used and IP-address is kept too. | |
| ADR learnedMacAddress | 1.3.6.1.4.1.343.6.11.2.9.1.1 | EthMacAddress | read-only | The MAC address for a station. |
| OCT learnedMacType | 1.3.6.1.4.1.343.6.11.2.9.1.2 | OCTET STRING | read-only | The 2 byte protocol/length identifier specified in a ethernet packet according to IEEE802.3 / ETHERNET II |
| INT learnedMacPortNo | 1.3.6.1.4.1.343.6.11.2.9.1.3 | INTEGER | read-only | The access-port on the VLAN device for a learned station. If portNo = 0 it means that this MAC is not learned locally. |
| IP learnedMacIpAddress | 1.3.6.1.4.1.343.6.11.2.9.1.4 | IpAddress | read-only | The IP-address of a learned station. |
| vlanLearnedMacVlanTable | 1.3.6.1.4.1.343.6.11.2.10 | not-accessible | A membership list of which stations are included in which VLANs in the actual domain. | |
| learnedMacVlanEntry | 1.3.6.1.4.1.343.6.11.2.10.1 | not-accessible | For every station (referred to by its MAC address) a list of VLANs that have the station as a member, can be retrieved. | |
| ADR learnedMacVlanMac | 1.3.6.1.4.1.343.6.11.2.10.1.1 | EthMacAddress | read-only | The MAC address of a learned station |
| INT learnedMacVlanIndex | 1.3.6.1.4.1.343.6.11.2.10.1.2 | INTEGER | read-only | The index of this VLAN, to be used when retrieving the next VLAN. |
| STR learnedMacVlanName | 1.3.6.1.4.1.343.6.11.2.10.1.3 | DisplayString | read-only | The name of the VLAN. |
| vlanLearnedVlanPortTable | 1.3.6.1.4.1.343.6.11.2.11 | not-accessible | A table of which VLANs exist on the ports. | |
| learnedVlanPortEntry | 1.3.6.1.4.1.343.6.11.2.11.1 | not-accessible | For each port a list of VLANs that are active on the port can be retrieved. | |
| INT learnedVlanPortNo | 1.3.6.1.4.1.343.6.11.2.11.1.1 | INTEGER | read-only | The if-index decribing the requested port. |
| INT learnedVlanPortVlanIndex | 1.3.6.1.4.1.343.6.11.2.11.1.2 | INTEGER | read-only | The index of this VLAN, to be used when retrieving the next VLAN. |
| STR learnedVlanPortVlanName | 1.3.6.1.4.1.343.6.11.2.11.1.3 | DisplayString | read-only | The name of the VLAN. |
| vlanLearnedVlanIdTable | 1.3.6.1.4.1.343.6.11.2.12 | not-accessible | Table of active VLAN id's | |
| learnedVlanIdEntry | 1.3.6.1.4.1.343.6.11.2.12.1 | not-accessible | A VLAN is active in a device, if a station connected to that device has become a member of the VLAN. | |
| INT learnedVlanId | 1.3.6.1.4.1.343.6.11.2.12.1.1 | INTEGER | read-only | The index of the VLAN. |
| STR learnedVlanIdVlanName | 1.3.6.1.4.1.343.6.11.2.12.1.2 | DisplayString | read-only | The name of the VLAN. |
| OCT vlanLearnedSnmpMgtVlanIds | 1.3.6.1.4.1.343.6.11.2.13 | OCTET STRING | read-only | This object will return a list of VLAN id's for the incoming SNMP request, usable to determine which VLANs the Mgt station itself belongs to. The answer is an Octet-string consisting of 16-bit unsigned integers, up to a maximum of 127 id's. If more VLAN id's should exist, only the first 127 will be returned in the reply. |
| INT vlanLearnedMacVlanFlush | 1.3.6.1.4.1.343.6.11.2.14 | INTEGER | read-write | Setting this object to 1 will flush the MAC-VLAN table of the entire distributed domain. |
| vlanIsl | 1.3.6.1.4.1.343.6.11.3 | |||
| islTable | 1.3.6.1.4.1.343.6.11.3.1 | not-accessible | A list of interconnected VLAN aware devices sharing the same doamin on a port. | |
| islEntry | 1.3.6.1.4.1.343.6.11.3.1.1 | not-accessible | On each switch vlan link a list of connected devices referred to by MAC- and IP-address. | |
| INT islIfIndex | 1.3.6.1.4.1.343.6.11.3.1.1.1 | INTEGER | read-only | The if-index decribing the requested port. |
| ADR islMacAddress | 1.3.6.1.4.1.343.6.11.3.1.1.2 | EthMacAddress | read-only | The MAC address of an SVL station. |
| IP islIpAddress | 1.3.6.1.4.1.343.6.11.3.1.1.3 | IpAddress | read-only | The IP-address of an SVL station |
| vlanEditToken | 1.3.6.1.4.1.343.6.11.4 | |||
| ADR editTokenOwnerMacAddress | 1.3.6.1.4.1.343.6.11.4.1 | EthMacAddress | read-only | The MAC address of the station that is currently locking the global VLAN configuration. |
| IP editTokenOwnerIpAddress | 1.3.6.1.4.1.343.6.11.4.2 | IpAddress | read-only | The IP-address of the station that is currently locking the global VLAN configuration. |
| STR editTokenOwnerSysName | 1.3.6.1.4.1.343.6.11.4.3 | DisplayString | read-only | The System Name of the station that is currently locking the global VLAN configuration. |
| INT editTokenOwnerApplication | 1.3.6.1.4.1.343.6.11.4.4 | INTEGER | read-only | The Application that is currently locking the global VLAN configuration. |
| IP editTokenOwnerSnmpIpAddress | 1.3.6.1.4.1.343.6.11.4.5 | IpAddress | read-only | The IP address of the IP host that has taken the edit token via SNMP |
| OCT editTokenClaimReq | 1.3.6.1.4.1.343.6.11.4.6 | OCTET STRING | read-write | This object is used to claim the Token to make changes to the VLAN configuration. Parameters are supplied in a binary coded octet string. Request will fail if sequence number given is lower than or equal to active configuration sequence number. Binary format: [] seqNo = sequence number expected to be next suggestNewSeqNo = if 1 device will assign allocForSNMP = if editing from SNMP set to 1 |
| INT editTokenLastClaimRspRetVal | 1.3.6.1.4.1.343.6.11.4.7 | INTEGER | read-only | Returns the last error code for the Claim Edit Token call. |
| INT editTokenReleaseReq | 1.3.6.1.4.1.343.6.11.4.8 | INTEGER | read-write | Object used to release the Token. When setting object an integer indicating 1) Abandon changes, 2) Save changes, 3) Save changes and wait for confirmation (if not confirmed the device returns to the previous configuration) must be given or 4) we are changing VLAN mode/name and want to have our System VLAN (id=24) back, to ensure correct connectivity after the change |
| INT editTokenLastReleaseRspRetVal | 1.3.6.1.4.1.343.6.11.4.9 | INTEGER | read-only | Returns the last error code for the Release Edit Token call. |
| INT editTokenForceReleaseReq | 1.3.6.1.4.1.343.6.11.4.10 | INTEGER | read-write | A forced release of the edit token can be issued by an IP host via SNMP by setting this object on the MVS. |
| INT editTokenClientState | 1.3.6.1.4.1.343.6.11.4.11 | INTEGER | read-only | The edit token state of the client |
| TIK editTokenTakenTime | 1.3.6.1.4.1.343.6.11.4.12 | TimeTicks | read-only | The time that the edit token has been allocated (in hundreds of a second) |
| INT editTokenLastForceReleaseRspRetVal | 1.3.6.1.4.1.343.6.11.4.13 | INTEGER | read-only | Returns the last error code for the Release Edit Token call. |
| INT editTokenServerState | 1.3.6.1.4.1.343.6.11.4.14 | INTEGER | read-only | The edit token state of the server. |
| vlanTrapObjects | 1.3.6.1.4.1.343.6.11.6 | |||
| STR previousVlanDomainName | 1.3.6.1.4.1.343.6.11.6.1 | DisplayString | not-accessible | Internal value used when sending SNMP traps |
| INT vlanParsingErrorNo | 1.3.6.1.4.1.343.6.11.6.2 | INTEGER | not-accessible | Internal value used when sending SNMP traps |
| OCT vlanParsingErrorText | 1.3.6.1.4.1.343.6.11.6.3 | OCTET STRING | not-accessible | Internal value used when sending SNMP traps |
| IP originatorIpAddress | 1.3.6.1.4.1.343.6.11.6.4 | IpAddress | not-accessible | Internal value used when sending SNMP traps |
| ADR originatorMacAddress | 1.3.6.1.4.1.343.6.11.6.5 | EthMacAddress | not-accessible | Internal value used when sending SNMP traps |
| OCT originatorSysName | 1.3.6.1.4.1.343.6.11.6.6 | OCTET STRING | not-accessible | Internal value used when sending SNMP traps |
| IP originatorMgtStationIpAddress | 1.3.6.1.4.1.343.6.11.6.7 | IpAddress | not-accessible | Internal value used when sending SNMP traps |
RFC description
Manages VLAN policy configuration, learning, and ISL (Inter-Switch Link) operations on Intel network devices.
Start monitoring Intel Ethernet switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.