HPN-ICF-NQA-MIB

All MIBs › HPN-ICF-NQA-MIB

Last Updated: 2006-08-14

Category: Technology: SLA/OAM, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Manages Network Quality Analysis (NQA) test instances for probing delay, jitter, and loss on HP/Comware devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-NQA-MIB?

HPN-ICF-NQA-MIB is an HP Networking (H3C-derived ICF platform) proprietary MIB (built on DISMAN-PING-MIB, supplementing RFC 2925) implementing NQA (Network Quality Analyzer) synthetic-test probes. Its control table, keyed by test, records target/source port, TTL, jitter-test admin interval/packet count, HTTP operation type/string, FTP operation type/username/password/string, VPN instance, history retention time/enable, ICPIF advantage factor, and codec type, while a results table records RTT disconnects, timeouts, busies, and no-connections. As a performance/diagnostic MIB it lets an administrator run and review synthetic HTTP/FTP/jitter/voice-quality probes on an HP Networking device. It is deployed on HP Networking (H3C-derived) equipment (NQA probes). Engineers can download the HPN-ICF-NQA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-NQA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP Networking (H3C-derived) equipment (NQA probes)

Monitoring Examples

An administrator checks hpnicfNqaResultsRttTimeouts to diagnose a failing synthetic-test probe run via NQA on an HP Networking device.

What Can Be Monitored

synthetic HTTP/FTP/jitter/voice-quality probe results

Imported Objects

From DISMAN-PING-MIB

pingCtlDescr	OBJECT-TYPE
pingCtlEntry	OBJECT-TYPE
pingCtlOwnerIndex	OBJECT-TYPE
pingCtlTargetAddress	OBJECT-TYPE
pingCtlTargetAddressType	OBJECT-TYPE
pingCtlTestName	OBJECT-TYPE
pingCtlType	OBJECT-TYPE

From HPN-ICF-OID-MIB

hpnicfRhw

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using hpnicfNqaJitterStatsNumOfRTT OID:

Select an HP Networking (H3C-derived) equipment (NQA synthetic-test probes) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfNqaJitterStatsNumOfRTT into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of received destination device responses with which jitter test can reach round-trip time. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the jitter climbs well above its normal baseline, since rising jitter often signals network congestion or a degrading path. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfNqa	1.3.6.1.4.1.11.2.14.11.15.8.3			The private MIB file includes the test information of the device. It is supplementary for rfc2925.txt.
hpnicfNqaObjects	1.3.6.1.4.1.11.2.14.11.15.8.3.1
STR hpnicfNqaMIBVersion	1.3.6.1.4.1.11.2.14.11.15.8.3.1.1	DisplayString	read-only	Version string of this MIB. The format will be: 'Version.Release.Patch: Description' An instance likes: '1.0.0: Initial NQA MIB'
hpnicfNqaCtlTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2		not-accessible	Defines the NQA Control Extend Table for providing, via SNMP, the capability of performing network analysis operations at a remote host.
hpnicfNqaCtlEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1		not-accessible	Defines an entry in the hpnicfNqaCtlTable. The operation of this table is same as that of pingResultsTable.
I32 hpnicfNqaCtlTargetPort	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.1	Integer32	read-create	The destination port that may be used by udpEcho, tcpConnect and jitter probes.
I32 hpnicfNqaCtlSourcePort	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.2	Integer32	read-create	The source port that may be used by all tests except for dns and dlsw. If no source port is specified, system will create a random port as source port.
I32 hpnicfNqaCtlTTL	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.3	Integer32	read-create	Specifies the value to store in the TTL Field in the IP packet used to encapsulate the NQA probe.
I32 hpnicfNqaCtlJitterAdminInterval	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.4	Integer32	read-create	Time value in milliseconds that is an interval between two continuous probes in jitter test. This object is only used by jitter test.
I32 hpnicfNqaCtlJitterAdminNumPackets	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.5	Integer32	read-create	Packet number that specifys how many packets will be sent in one jitter test. This object is only used by jitter test.
INT hpnicfNqaCtlHttpOperationType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.6	INTEGER	read-create	Http operation type: get, post or raw.
STR hpnicfNqaCtlHttpOperationString	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.7	DisplayString	read-create	Http operation string. For example, if the http operation type is get, the string will be url, home page and http version.
INT hpnicfNqaCtlFtpOperationType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.8	INTEGER	read-create	Ftp operation type.
STR hpnicfNqaCtlFtpUsername	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.9	DisplayString	read-create	Ftp username.
STR hpnicfNqaCtlFtpPassword	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.10	DisplayString	read-create	Ftp password.
STR hpnicfNqaCtlFtpOperationString	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.11	DisplayString	read-create	Ftp operation string. If the ftp operation type is get, the string must be the file name which will be gotten from ftp server.
STR hpnicfNqaCtlVPNInstance	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.12	DisplayString	read-create	VPN name by which system finds route in the specified VPN to send NQA probe packets.
I32 hpnicfNqaCtlHistoryKeptTime	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.13	Integer32	read-create	To indicate how long the history records will be saved in the pingProbeHistoryTable table after the test stopped.
INT hpnicfNqaCtlHistoryEnable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.14	INTEGER	read-create	To indicate whether the history should be recorded in the PingProbeHistoryTable or not. enabled(1) --history will be recorded disabled(2) --history will not be recorded.
I32 hpnicfNqaCtlICPIFAdvFactor	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.15	Integer32	read-create	The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. This is applicable only for the jitter probe. Suggestion values: \|-----------------------------------\|-------\| \| Service \|factor \| \|-----------------------------------\|-------\| \|conventional wire-line \| 0 \| \|-----------------------------------\|-------\| \|mobility within Building \| 5 \| \|-----------------------------------\|-------\| \|mobility within geographical area \| 10 \| \|-----------------------------------\|-------\| \|access to hard-to-reach location \| 20 \| \|-----------------------------------\|-------\|
INT hpnicfNqaCtlCodecType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.2.1.16	INTEGER	read-create	To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
hpnicfNqaResultsTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3		not-accessible	Defines the NQA Results Extend Table for providing the capability of performing NQA operations at a remote host. The results of these operations are stored in the hpnicfNqaResultsTable. The operation of this table is same as that of pingResultsTable.
hpnicfNqaResultsEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1		not-accessible	The operation of this table is same as that of pingResultsTable.
U32 hpnicfNqaResultsRttNumDisconnects	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.1	Unsigned32	read-only	The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
U32 hpnicfNqaResultsRttTimeouts	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.2	Unsigned32	read-only	The number of times that a NQA probe failed because the probe timed out.
U32 hpnicfNqaResultsRttBusies	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.3	Unsigned32	read-only	The number of times that a NQA probe failed because all NQA tasks have been running. If a new probe fails to start, the value of this object is incremented. The next test will not start until the next Frequency.
U32 hpnicfNqaResultsRttNoConnections	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.4	Unsigned32	read-only	The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
U32 hpnicfNqaResultsRttDrops	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.5	Unsigned32	read-only	The number of times that a NQA operation failed to initiated for unavailibility of necessary internal resources.
U32 hpnicfNqaResultsRttSequenceErrors	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.6	Unsigned32	read-only	The number of packets arrived out of sequence.
U32 hpnicfNqaResultsRttStatsErrors	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.7	Unsigned32	read-only	The number of some other errors.
U32 hpnicfNqaResultsMaxDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.8	Unsigned32	read-only	The maximal delay from source device to destination device. Currently this value is only used for jitter test, and this value must be 0 in other type test. In jitter test, if destination system time is not valid, the SD delay may be set 0.
U32 hpnicfNqaResultsMaxDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.9	Unsigned32	read-only	The maximal delay from destination device to source device. Currently this value is only used for jitter test, and this value is 0 in other type test. In jitter test, if destination system time is not valid, the DS delay may be set 0.
U32 hpnicfNqaResultsLostPacketRatio	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.10	Unsigned32	read-only	The value of this object reflects the drop rate of NQA test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
U32 hpnicfNqaResultsPacketLateArrival	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.11	Unsigned32	read-only	The value of this object indicates the number of the packets that arrived after the timeout.
U32 hpnicfNqaResultsRttSum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.12	Unsigned32	read-only	The sum of round trip time.
U32 hpnicfNqaResultsNumOfDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.13	Unsigned32	read-only	The number of delay from source to destination that are successfully measured.
U32 hpnicfNqaResultsMinDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.14	Unsigned32	read-only	The minimum of all one way times from source to destination.
U32 hpnicfNqaResultsSumDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.15	Unsigned32	read-only	The sum of one way times from source to destination.
U32 hpnicfNqaResultsSum2DelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.16	Unsigned32	read-only	The sum of squares of one way times from source to destination.
U32 hpnicfNqaResultsNumOfDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.17	Unsigned32	read-only	The number of delay from destination to source that are successfully measured.
U32 hpnicfNqaResultsMinDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.18	Unsigned32	read-only	The minimum of all one way times from destination to source.
U32 hpnicfNqaResultsSumDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.19	Unsigned32	read-only	The sum of one way times from destination to source.
U32 hpnicfNqaResultsSum2DelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.3.1.20	Unsigned32	read-only	The sum of squares of one way times from destination to source.
hpnicfNqaJitterStatsTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4		not-accessible	Statistics table for latest jitter activity.
hpnicfNqaJitterStatsEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1		not-accessible	An entry contains the statistics for the latest jitter activity. This entry is created only if the pingCtlType is hpnicfNqajitter.
C32 hpnicfNqaJitterStatsNumOfRTTEx	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.1	Counter32	read-only	The number of received destination device responses with which jitter test can reach round-trip time.
G32 hpnicfNqaJitterStatsMinOfPositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.2	Gauge32	read-only	The value of time that records the minimal positive jitter value from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsMaxOfPositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.3	Gauge32	read-only	The value of time that records the maximal positive jitter value from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsNumOfPositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.4	Gauge32	read-only	The number that records positive jitter times from source to destination in the jitter test. The total number of the value of all positive jitters in packets sent from source to destination.
G32 hpnicfNqaJitterStatsSumOfPositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.5	Gauge32	read-only	The value of time that records the sum of positive jitter values from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsSum2PositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.6	Gauge32	read-only	The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsMinOfNegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.7	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsMaxOfNegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.8	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsNumOfNegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.9	Gauge32	read-only	The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values in packets sent from source to destination.
G32 hpnicfNqaJitterStatsSumOfNegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.10	Gauge32	read-only	The value of time that records the sum of negative jitter values from source to destination in the jitter test. The total number of the value of all negative jitters in packets sent from source to destination.
G32 hpnicfNqaJitterStatsSum2NegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.11	Gauge32	read-only	The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
G32 hpnicfNqaJitterStatsMinOfPositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.12	Gauge32	read-only	The value of time that records the minimal positive jitter value from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsMaxOfPositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.13	Gauge32	read-only	The value of time that records the maximal positive jitter value from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsNumOfPositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.14	Gauge32	read-only	The number that records positive jitter times from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsSumOfPositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.15	Gauge32	read-only	The value of time that records the sum of positive jitter values from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsSum2PositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.16	Gauge32	read-only	The value of time that records the sum of square of positive jitter values from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsMinOfNegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.17	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsMaxOfNegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.18	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsNumOfNegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.19	Gauge32	read-only	The number that records negative jitter times from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsSumOfNegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.20	Gauge32	read-only	The value of time that records the sum of negative jitter values from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsSum2NegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.21	Gauge32	read-only	The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
G32 hpnicfNqaJitterStatsPacketLossSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.22	Gauge32	read-only	The lost packets number sent from source to destination.
G32 hpnicfNqaJitterStatsPacketLossDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.23	Gauge32	read-only	The lost packets number sent from destination to source.
G32 hpnicfNqaJitterStatsAvePositivesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.24	Gauge32	read-only	The value of time that records the average positive jitter value from source to destination.
G32 hpnicfNqaJitterStatsAveNegativesSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.25	Gauge32	read-only	The value of time that records the average negative jitter value from source to destination.
G32 hpnicfNqaJitterStatsAvePositivesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.26	Gauge32	read-only	The value of time that records the average positive jitter value from destination to source.
G32 hpnicfNqaJitterStatsAveNegativesDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.27	Gauge32	read-only	The value of time that records the average negative jitter value from destination to source.
G32 hpnicfNqaJitterStatsPktLossUnknown	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.28	Gauge32	read-only	The number of packets which is lost with unknown reason.
G32 hpnicfNqaJitterStatsOperOfICPIF	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.29	Gauge32	read-only	The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
G32 hpnicfNqaJitterStatsOperOfMOS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.4.1.30	Gauge32	read-only	The MOS (Mean Opinion Score) value for the latest jitter test.
INT hpnicfNqaAgentEnable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.5	INTEGER	read-write	Enable NQA agent function.
hpnicfNqaTcpServerTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.6		not-accessible	A table which contains the status of NQA tcp server configuration information.
hpnicfNqaTcpServerEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1		not-accessible	A table which contains the status of NQA tcp server configuration information. This entry includes not only the tcp server ip address but also the tcp server port.
IP hpnicfNqaTcpServerIpAddress	1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.1	InetAddress	not-accessible	Tcp server's ip address.
I32 hpnicfNqaTcpServerPort	1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.2	Integer32	not-accessible	Tcp server's port number.
ROW hpnicfNqaTcpServerRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.3.1.6.1.3	RowStatus	read-create	hpnicfNqaTcpServerIpAddress and hpnicfNqaTcpServerPort must be set during a creation operation.
hpnicfNqaUdpServerTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.7		not-accessible	Status of NQA udp server configuration information.
hpnicfNqaUdpServerEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1		not-accessible	This entry includes not only the udp server ip address but also the udp server udp port.
IP hpnicfNqaUdpServerIpAddress	1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.1	InetAddress	not-accessible	Udp server's ip address.
I32 hpnicfNqaUdpServerPort	1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.2	Integer32	not-accessible	Udp server's port number.
ROW hpnicfNqaUdpServerRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.3.1.7.1.3	RowStatus	read-create	hpnicfNqaUdpServerIpAddress and hpnicfNqaUdpServerPort must be set during a creation operation.
INT hpnicfNqaServerEnable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.8	INTEGER	read-write	Enable NQA server function.
I32 hpnicfNqaStatsMaxGroupNumber	1.3.6.1.4.1.11.2.14.11.15.8.3.1.9	Integer32	read-only	The maximum number saved per group. The maximum value of hpnicfNqaCtlStatisticsGroupNumber can not exceed the value of this object.
hpnicfNqaStatisticsCtlTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10		not-accessible	Defines the NQA statistics control table for providing, via SNMP, the capability of performing NQA operations at a remote host. The results of these operations are stored in the hpnicfNqaStatisticsResultsTable and the hpnicfNqaGroupStatsJitterTable.
hpnicfNqaStatisticsCtlEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1		not-accessible	Defines an entry in the hpnicfNqaStatisticsCtlTable. The hpnicfNqaStatisticsCtlTable has the same index as the pingCtlTable in order for a hpnicfNqaStatisticsCtlTable to correspond to the pingCtlEntry.
U32 hpnicfNqaCtlStatisticsInterval	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.1	Unsigned32	read-create	Statistic information will be calculated after the time that is the value of hpnicfNqaCtlStatisticsInterval.
U32 hpnicfNqaCtlStatisticsGroupNumber	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.2	Unsigned32	read-create	The value of this object indicates the number of group saved. The length of this object is from 1 to hpnicfNqaStatsMaxGroupNumber.
U32 hpnicfNqaCtlStatisticsKeptTime	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.3	Unsigned32	read-create	To indicate how long the statistic information will be saved after the test stops.
DAT hpnicfNqaCtlBeginTime	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.4	DateAndTime	read-create	Time at which the type-specified test will start.
U32 hpnicfNqaCtlLifeTime	1.3.6.1.4.1.11.2.14.11.15.8.3.1.10.1.5	Unsigned32	read-create	To indicate how long the type-specified test will last.
hpnicfNqaStatisticsResultsTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11		not-accessible	Defines the NQA statistics results table for providing the capability of performing NQA operations at a remote host. The statistics results of these operations in a statistic cycle are stored in the hpnicfNqaStatisticsResultsTable. The statistic cycle is the value of hpnicfNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that the probe statistics result (HpnicfNqaStatisticsResultsEntry) belongs to.
hpnicfNqaStatisticsResultsEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1		not-accessible	Defines an entry in the hpnicfNqaStatisticsResultsTable. The hpnicfNqaStatisticsResultsTable has the same index as the pingCtlTable in order for a hpnicfNqaStatisticsResultsEntry to correspond to the pingCtlEntry that caused it to be created.
U32 hpnicfNqaStatResIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.1	Unsigned32	not-accessible	An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hpnicfNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
IPt hpnicfNqaStatResIpTargetAddressType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.2	InetAddressType	read-only	This object indicates the type of address stored in the corresponding hpnicfNqaStatResIpTargetAddress object.
IP hpnicfNqaStatResIpTargetAddress	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.3	InetAddress	read-only	This object represent the host address to be used at a remote host for performing a network analysis operation.
G32 hpnicfNqaStatResMinRtt	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.4	Gauge32	read-only	The minimum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
G32 hpnicfNqaStatResMaxRtt	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.5	Gauge32	read-only	The maximum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
G32 hpnicfNqaStatResAverageRtt	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.6	Gauge32	read-only	The average NQA probe round-trip-time (RTT).
C32 hpnicfNqaStatResProbeResponses	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.7	Counter32	read-only	The number of responses received. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 hpnicfNqaStatResSentProbes	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.8	Counter32	read-only	The value of this object reflects the number of probes sent. The value of this object MUST be reported as 0 when no probes have been sent.
C32 hpnicfNqaStatResRttSumOfSquares	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.9	Counter32	read-only	This object contains the sum of the squares for all NQA responses received. The value of this object MUST be reported as 0 when no NQA responses have been received.
DAT hpnicfNqaStatResStartTime	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.10	DateAndTime	read-only	This object contains the start time of the statistic.
G32 hpnicfNqaStatResInterval	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.11	Gauge32	read-only	This object contains the interval between two times of statistic.
C32 hpnicfNqaStatResRttNumDisconnects	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.12	Counter32	read-only	The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
C32 hpnicfNqaStatResRttTimeouts	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.13	Counter32	read-only	The number of times that a probe failed because the probe timed out.
C32 hpnicfNqaStatResRttBusies	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.14	Counter32	read-only	The number of times that a NQA probe failed because errors related to sockets.
C32 hpnicfNqaStatResRttNoConnections	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.15	Counter32	read-only	The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
C32 hpnicfNqaStatResRttDrops	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.16	Counter32	read-only	The number of times that a NQA operation failed to initiate for unavailibility of necessary internal resources.
C32 hpnicfNqaStatResRttSequenceErrors	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.17	Counter32	read-only	The number of packets arrived out of sequence.
C32 hpnicfNqaStatResRttErrors	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.18	Counter32	read-only	The number of other errors.
G32 hpnicfNqaStatResLostPacketRatio	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.19	Gauge32	read-only	The value of this object reflects the drop rate of NQA test packet. For example, if the value is 30, that means source device only had received 70 percent packets of total sent packets.
C32 hpnicfNqaStatResPacketLateArrival	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.20	Counter32	read-only	The value of this object reflects the number of the packets that arrived after the timeout.
C32 hpnicfNqaStatResRttSum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.21	Counter32	read-only	This object contains the sum of the squares for all NQA responses received during the test lifetime. The value of this object MUST be reported as 0 when no NQA responses have been received.
C32 hpnicfNqaStatResNumOfDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.22	Counter32	read-only	The number of one way times from source to destination that are successfully measured.
G32 hpnicfNqaStatResMinDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.23	Gauge32	read-only	The minimum one way times from source to destination.
G32 hpnicfNqaStatResMaxDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.24	Gauge32	read-only	The maximum one way times from source to destination.
C32 hpnicfNqaStatResSumDelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.25	Counter32	read-only	The sum of one way times from source to destination.
C32 hpnicfNqaStatResSum2DelaySD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.26	Counter32	read-only	The sum of squares of one way times from source to destination.
C32 hpnicfNqaStatResNumOfDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.27	Counter32	read-only	The number of one way times from destination to source that are successfully measured.
G32 hpnicfNqaStatResMinDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.28	Gauge32	read-only	The minimum one way times from destination to source.
G32 hpnicfNqaStatResMaxDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.29	Gauge32	read-only	The maximum one way times from destination to source.
C32 hpnicfNqaStatResSumDelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.30	Counter32	read-only	The sum of one way times from destination to source.
C32 hpnicfNqaStatResSum2DelayDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.11.1.31	Counter32	read-only	The sum of squares of one way times from destination to source.
hpnicfNqaGroupStatsJitterTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12		not-accessible	Test Group Statistic table for jitter activity in a statistic cycle. The statistic cycle is the value of hpnicfNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that a probe statistics result (HpnicfNqaStatisticsResultsEntry) belongs to.
hpnicfNqaGroupStatsJitterEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1		not-accessible	An entry contains the group statistic information for jitter activity. This entry is created only if the pingCtlType is hpnicfNqajitter.
U32 hpnicfNqaStatJitterIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.1	Unsigned32	not-accessible	An entry in this table is created when the statistic result of a NQA probe in a statistic cycle is determined. An implementation MUST start assigning hpnicfNqaStatJitterIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
G32 hpnicfNqaStatJitterMinOfPosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.2	Gauge32	read-only	The value of time that records the minimal positive jitter value from source to destination in jitter test.
G32 hpnicfNqaStatJitterMaxOfPosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.3	Gauge32	read-only	The value of time that records the maximal positive jitter value from source to destination in the jitter test.
C32 hpnicfNqaStatJitterNumOfPosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.4	Counter32	read-only	The total number of positive jitters from source to destination in the jitter test.
C32 hpnicfNqaStatJitterSumOfPosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.5	Counter32	read-only	The value of time that records the sum of positive jitter values from source to destination in the jitter test.
C32 hpnicfNqaStatJitterSumOfSquarePosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.6	Counter32	read-only	The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
G32 hpnicfNqaStatJitterMinOfNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.7	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
G32 hpnicfNqaStatJitterMaxOfNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.8	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
C32 hpnicfNqaStatJitterNumOfNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.9	Counter32	read-only	The total number of negative jitters from source to destination in the jitter test.
C32 hpnicfNqaStatJitterSumOfNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.10	Counter32	read-only	The value of time that records the sum of negative jitter values from source to destination in the jitter test.
C32 hpnicfNqaStatJitterSumOfSquareNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.11	Counter32	read-only	The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
G32 hpnicfNqaStatJitterMinOfPosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.12	Gauge32	read-only	The value of time that records the minimal positive jitter value from destination to source in the jitter test.
G32 hpnicfNqaStatJitterMaxOfPosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.13	Gauge32	read-only	The value of time that records the maximal positive jitter value from destination to source in the jitter test.
C32 hpnicfNqaStatJitterNumOfPosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.14	Counter32	read-only	The total number of positive jitters from destination to source in the jitter test.
C32 hpnicfNqaStatJitterSumOfPosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.15	Counter32	read-only	The value of time that records the sum of positive jitter values from destination to source in the jitter test.
C32 hpnicfNqaStatJitterSumOfSquarePosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.16	Counter32	read-only	The value of time that records the sum of square of positive jitter values destination to source in the jitter test.
G32 hpnicfNqaStatJitterMinOfNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.17	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
G32 hpnicfNqaStatJitterMaxOfNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.18	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
C32 hpnicfNqaStatJitterNumOfNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.19	Counter32	read-only	The total number of negative jitters from destination to source in the jitter test.
C32 hpnicfNqaStatJitterSumOfNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.20	Counter32	read-only	The value of time that records the sum of negative jitter values from destination to source in the jitter test.
C32 hpnicfNqaStatJitterSumOfSquareNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.21	Counter32	read-only	The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
C32 hpnicfNqaStatJitterPacketLossSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.22	Counter32	read-only	The lost packets number sent from source to destination.
C32 hpnicfNqaStatJitterPacketLossDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.23	Counter32	read-only	The lost packets number sent from destination to source.
G32 hpnicfNqaStatJitterAvePosSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.24	Gauge32	read-only	The value of time that records the average positive jitter value from source to destination.
G32 hpnicfNqaStatJitterAveNegSD	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.25	Gauge32	read-only	The value of time that records the average negative jitter value from source to destination.
G32 hpnicfNqaStatJitterAvePosDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.26	Gauge32	read-only	The value of time that records the average positive jitter value from destination to source.
G32 hpnicfNqaStatJitterAveNegDS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.27	Gauge32	read-only	The value of time that records the average negative jitter value from destination to source.
C32 hpnicfNqaStatJitterPktLossUnknown	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.28	Counter32	read-only	The number of packets which is lost with unknown reason.
G32 hpnicfNqaStatJitterMaxOfICPIF	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.29	Gauge32	read-only	The maximum of all ICPIF values in a statistic cycle for jitter test.
G32 hpnicfNqaStatJitterMinOfICPIF	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.30	Gauge32	read-only	The minimum of all ICPIF values in a statistic cycle for jitter test.
G32 hpnicfNqaStatJitterMaxOfMOS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.31	Gauge32	read-only	The maximum of all MOS values in a statistic cycle for jitter test.
G32 hpnicfNqaStatJitterMinOfMOS	1.3.6.1.4.1.11.2.14.11.15.8.3.1.12.1.32	Gauge32	read-only	The minimum of all MOS values in a statistic cycle for jitter test.
hpnicfNqaReactionTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13		not-accessible	A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
hpnicfNqaReactionEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1		not-accessible	Defines an entry in the hpnicfNqaReactionTable. The first two index elements identify the pingCtlEntry that a hpnicfNqaReactItemIndex belongs to. The third index element selects a single reaction.
STR hpnicfNqaReactOwnerIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.1	SnmpAdminString	accessible-for-notify	The first index of hpnicfNqaReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable. hpnicfNqaReactOwnerIndex and hpnicfNqaReactTestName identify an existed test.
STR hpnicfNqaReactTestName	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.2	SnmpAdminString	accessible-for-notify	The second index of hpnicfNqaReactionTable, it is the same as pingCtlTestName in pingCtlTable. hpnicfNqaReactOwnerIndex and hpnicfNqaReactTestName identify an existed test.
U32 hpnicfNqaReactItemIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.3	Unsigned32	accessible-for-notify	The third index of hpnicfNqaReactionTable, it definitely identifies one of the reaction configurations for a test.
INT hpnicfNqaReactCheckedElement	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.4	INTEGER	read-create	A list of reaction condition type. 'probetime' and 'probefailure' are valid when pingCtlType of the test is not hpnicfNqajitter. 'jitterOwdSD': one way time from source to destination in jitter test. 'jitterOwdDS': one way time from destination to source in jitter test. 'jitterrtt', 'jitterpacketloss', 'jittersd', 'jitterds', 'jitterOwdSD' and 'jitterOwdDS' are valid when pingCtlType of the test is hpnicfNqajitter. 'icpif' and 'mos' are valid when pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
U32 hpnicfNqaReactThresholdUpperLimit	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.5	Unsigned32	read-create	This object defines an administrative upper-threshold value for hpnicfNqaReactCheckedElement. The value of this object is zero if hpnicfNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
U32 hpnicfNqaReactThresholdLowerLimit	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.6	Unsigned32	read-create	This object defines an administrative lower-threshold value for hpnicfNqaReactCheckedElement. The value of hpnicfNqaReactThresholdLowerLimit should be equal or less than the value of hpnicfNqaReactThresholdUpperLimit. The value of this object is zero if hpnicfNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
INT hpnicfNqaReactThresholdType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.7	INTEGER	read-create	This object defines the reaction threshold types. invalid(0): Invalid value. average(1): If reaction threshold type is average and the average value of watched operation exceeds threshold limit, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. consecutive(2): If reaction threshold type is consecutive and the times of watched operation consecutively exceeds the limit specified by hpnicfNqaReactThresholdConsecNum, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. accumulative(3): If reaction threshold type is accumulative and the times of watched operation accumulatively exceeds the limit specified by hpnicfNqaReactThresholdAccumNum, an action specified in hpnicfNqaReactActionType is generated when hpnicfNqaReactCurrentStatus changes. If reaction threshold type is not configured, the value of this object is 'invalid'.
U32 hpnicfNqaReactThresholdConsecNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.8	Unsigned32	read-create	This object defines a consecutive threshold limit. The value is zero when hpnicfNqaReactThresholdType is not 'consecutive'.
U32 hpnicfNqaReactThresholdAccumNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.9	Unsigned32	read-create	This object defines an accumulative threshold limit. The value is zero when the hpnicfNqaReactThresholdType is not 'accumulative'.
INT hpnicfNqaReactActionType	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.10	INTEGER	read-create	Specifies the type of reaction to generate if the specified violation type occurs for the monitored element: none - No reaction is generated trapOnly - A trap is generated triggerOnly - All trigger actions defined for this entry are generated trapAndTrigger - Both a trap and all trigger actions are generated
INT hpnicfNqaReactCurrentStatus	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.11	INTEGER	read-only	Specifies the current status of this reaction entry: invalid - The status of the reaction entry is unknown. overThreshold - The status of the reaction entry is overThreshold when the monitored result exceeds the threshold value for the hpnicfNqaReactThresholdType. belowThreshold - The status of the reaction entry is belowThreshold when the monitored result is under the threshold value for the hpnicfNqaReactThresholdType.
ROW hpnicfNqaReactRowStatus	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.12	RowStatus	read-create	This object allows entries to be created and deleted in the hpnicfNqaReactionTable. Creation of an entry in this table results in a new set of reaction configurations which take effect immediately. Deletion of an entry in this table results in corresponding reaction configurations are being deleted and stop taking effect.
U32 hpnicfNqaReactCheckedNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.13	Unsigned32	read-only	The number of checked element samples that are monitored.
U32 hpnicfNqaReactThresholdNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.13.1.14	Unsigned32	read-only	The number of checked element samples that are over threshold.
hpnicfNqaStatisticsReactionTable	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14		not-accessible	A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
hpnicfNqaStatisticsReactionEntry	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1		not-accessible	Defines an entry in the hpnicfNqaStatisticsReactionTable. The first two index elements identify the pingCtlEntry that a hpnicfNqaReactItemIndex belongs to. The third index element identifies an entry in the hpnicfNqaStatisticsResultsTable. The forth index element selects a single reaction.
STR hpnicfNqaStatReactOwnerIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.1	SnmpAdminString	not-accessible	The first index of hpnicfNqaStatisticsReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable.
STR hpnicfNqaStatReactTestName	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.2	SnmpAdminString	not-accessible	The second index of hpnicfNqaStatisticsReactionTable, it is the same as pingCtlTestName in pingCtlTable.
U32 hpnicfNqaStatReactIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.3	Unsigned32	not-accessible	The third index of hpnicfNqaStatisticsReactionTable. An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hpnicfNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
U32 hpnicfNqaStatReactItemIndex	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.4	Unsigned32	not-accessible	The forth index of hpnicfNqaStatisticsReactionTable, it definitely identifies one of the reaction configurations for a test
C32 hpnicfNqaStatReactCheckedNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.5	Counter32	read-only	The number of checked element samples that are monitored.
C32 hpnicfNqaStatReactThresholdNum	1.3.6.1.4.1.11.2.14.11.15.8.3.1.14.1.6	Counter32	read-only	The number of checked element samples that are over threshold.
hpnicfNqaImplementationTypeDomains	1.3.6.1.4.1.11.2.14.11.15.8.3.2
hpnicfNqaUdpEcho	1.3.6.1.4.1.11.2.14.11.15.8.3.2.1			Indicates that an implementation is using the UDP based echo server. Notes: The hpnicfNqaCtlTargetPort and hpnicfNqaCtlSourcePort need to be set, while in the pingUdpEcho Node, hpnicfNqaCtlTargetPort must be set to the default value.
hpnicfNqaTcpconnect	1.3.6.1.4.1.11.2.14.11.15.8.3.2.2			Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hpnicfNqaCtlTargetPort and hpnicfNqaCtlSourcePort need to be set, while in the pingTcpConnectionAttempt Node, hpnicfNqaCtlTargetPort must be set to the default value.
hpnicfNqajitter	1.3.6.1.4.1.11.2.14.11.15.8.3.2.3			Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the NQA(Network Quality Analysis) application to perform delay variance analysis.
hpnicfNqaHttp	1.3.6.1.4.1.11.2.14.11.15.8.3.2.4			Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. It causes the NQA application to perform a download of the object specified in the URL.
hpnicfNqadlsw	1.3.6.1.4.1.11.2.14.11.15.8.3.2.5			Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the NQA application to perform a keepalive operation to measure the response time of a DLSw peer.
hpnicfNqadhcp	1.3.6.1.4.1.11.2.14.11.15.8.3.2.6			Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the NQA application to perform an IP Address lease request/teardown operation.
hpnicfNqaftp	1.3.6.1.4.1.11.2.14.11.15.8.3.2.7			Indicates that an implementation is using tcp packet for ftp connect and data transfer.
hpnicfNqaNotifications	1.3.6.1.4.1.11.2.14.11.15.8.3.3
NTF hpnicfNqaProbeTimeOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.1			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. Probe time(equals to RTT for some type of tests) is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. 2. The probe time is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum. 3. The probe time is consecutively in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdConsecNum. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hpnicfNqajitter.
NTF hpnicfNqaJitterRTTOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.2			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average NQA round-trip-time (RTT) of jitter packets is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. 2. The RTT of jitter packets is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
NTF hpnicfNqaProbeFailure	1.3.6.1.4.1.11.2.14.11.15.8.3.3.3			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the probe test accumulatively failed for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test while the value of hpnicfNqaReactThresholdType is 'accumulative'. 2. When the probe test consecutively failed for a number of times specified in hpnicfNqaReactThresholdConsecNum in one test while the value of hpnicfNqaReactThresholdType is 'consecutive'. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hpnicfNqajitter.
NTF hpnicfNqaJitterPacketLoss	1.3.6.1.4.1.11.2.14.11.15.8.3.3.4			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the jitter packets accumulatively lost for a number of times specified in hpnicfNqaReactThresholdAccumNum in one test while the value of hpnicfNqaReactThresholdType is 'accumulative'. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
NTF hpnicfNqaJitterSDOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.5			The SD means the jitter values from source to destination. It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of SD in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit and the hpnicfNqaReactThresholdType is specified as 'average' type. 2. The average of SD in one jitter test is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum and the hpnicfNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
NTF hpnicfNqaJitterDSOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.6			The DS means the jitter values from destination to source. It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of DS in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit and the hpnicfNqaReactThresholdType is specified as 'average' type. 2. The average of DS in one jitter test is accumulatively not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit for a number of times specified in hpnicfNqaReactThresholdAccumNum and the hpnicfNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hpnicfNqajitter.
NTF hpnicfNqaICPIFOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.7			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the ICPIF value in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
NTF hpnicfNqaMOSOverThreshold	1.3.6.1.4.1.11.2.14.11.15.8.3.3.8			It is generated when the value of hpnicfNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the MOS value in one jitter test is not in the range hpnicfNqaReactThresholdLowerLimit through hpnicfNqaReactThresholdUpperLimit. This notification is valid only when hpnicfNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hpnicfNqajitter and hpnicfNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.

RFC description

HP extended network quality analysis MIB for monitoring jitter, delay, and packet loss on network paths.

Start monitoring HP Networking (H3C-derived) equipment (NQA synthetic-test probes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-NQA-MIB