COLUBRIS-PUBLIC-ACCESS-MIB

All MIBs › COLUBRIS-PUBLIC-ACCESS-MIB

Organization: Colubris Networks, Inc.

Last Updated: 2005-11-04

Category: RADIUS and AAA, Vendor: HP/HPE, Wireless and WLAN

Description: Manages hotspot public access portal settings and subscriber authentication on Colubris/HP platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is COLUBRIS-PUBLIC-ACCESS-MIB?

COLUBRIS-PUBLIC-ACCESS-MIB manages hotspot/public-access portal configuration and subscriber session status on Colubris (later HP) wireless access devices, the technology commonly used for guest Wi-Fi and hospitality/hotspot deployments. It exposes both configuration data (authentication profile, accounting profile, session-timeout admin settings, config mode) and session-oriented status data (publicAccessStatus, publicAccessStatusChangedCause, current authenticated user name). Its monitoring value is centered on software/service status: publicAccessStatus and publicAccessStatusChangedCause reveal whether the public-access service is currently up and, if not, why it changed state, while publicAccessDeviceSessionTimeoutOperStatus versus the admin setting shows whether session timeout enforcement is actually active as configured. It relies on an external RADIUS/AAA infrastructure implied by publicAccessDeviceAuthenProfileIndex and publicAccessDeviceAccountingProfileIndex rather than defining authentication itself. It is typically deployed on Colubris/HP wireless access points or gateways providing hotel, cafe, or venue guest internet access. Network engineers evaluating or troubleshooting this functionality can download the COLUBRIS-PUBLIC-ACCESS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in COLUBRIS-PUBLIC-ACCESS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Colubris/HP wireless access point/gateway (hotspot deployment)

Monitoring Examples

An administrator would check publicAccessStatus and, if it's not operational, read publicAccessStatusChangedCause to determine why the hotspot service went down (e.g., configuration change vs. failure). publicAccessDeviceUserName would show the currently logged-in subscriber, and publicAccessUsersMaxCount compared against active sessions indicates whether the device is near its concurrent-user capacity. A mismatch between publicAccessDeviceSessionTimeoutAdminStatus (enabled) and publicAccessDeviceSessionTimeoutOperStatus (disabled) would flag that session timeout enforcement isn't actually taking effect, letting sessions run indefinitely.

What Can Be Monitored

public access service status and change cause
current authenticated user
session timeout admin vs operational status
authentication/accounting profile in use
max concurrent users
force-reconfiguration state

Imported Objects

From COLUBRIS-SMI

colubrisMgmtV2

OBJECT-IDENTITY

From COLUBRIS-TC

ColubrisNotificationEnable
ColubrisPriorityQueue
ColubrisProfileIndexOrZero
ColubrisSSIDOrNone
ColubrisSecurity
ColubrisUsersAuthenticationMode
ColubrisUsersAuthenticationType

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
MacAddress
TruthValue

How to Use in IPNetwork Monitor

Example using publicAccessUserSessionDuration OID:

Select a Colubris/HP wireless access point/gateway (hotspot, legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type publicAccessUserSessionDuration into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates how long the user's session has been active. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in seconds), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
colubrisPublicAccessMIB	1.3.6.1.4.1.8744.5.1			Colubris Networks Public Access MIB.
colubrisPublicAccessMIBObjects	1.3.6.1.4.1.8744.5.1.1
publicAccessGroup	1.3.6.1.4.1.8744.5.1.1.1
INT publicAccessStatus	1.3.6.1.4.1.8744.5.1.1.1.1	INTEGER	read-only	Identifies the current status of the authentication system.
OCT publicAccessStatusChangedCause	1.3.6.1.4.1.8744.5.1.1.1.2	OCTET STRING	read-only	Identifies the last cause of a status change. Mostly used by the publicAccessStatusChanged trap.
publicAccessDeviceGroup	1.3.6.1.4.1.8744.5.1.1.2
OCT publicAccessDeviceUserName	1.3.6.1.4.1.8744.5.1.1.2.1	OCTET STRING	read-write	Specifies the username that the device uses when authenticating itself to a RADIUS server.
OCT publicAccessDeviceUserPassword	1.3.6.1.4.1.8744.5.1.1.2.2	OCTET STRING	read-write	Specifies the password the device uses when authenticating to a RADIUS server. For security reasons, this should be set only if SNMP traffic is sent through a VPN tunnel. Reading this attribute will return an empty string.
U32 publicAccessDeviceSessionTimeoutAdminStatus	1.3.6.1.4.1.8744.5.1.1.2.3	Unsigned32	read-write	Specifies the interval of time between two consecutive authentication attempts in minutes. At each successful authentication the device configuration is refreshed. This is not the time between RADIUS Access Request when an authentication is proceeding without answers. For that element, see the RADIUS Profile definition.
U32 publicAccessDeviceSessionTimeoutOperStatus	1.3.6.1.4.1.8744.5.1.1.2.4	Unsigned32	read-only	Identifies the interval of time between two consecutive authentication attempts in seconds. At each successful authentication the device configuration is refreshed. This is not the time between RADIUS Access Request when an authentication is proceeding without answers. For that element, see the RADIUS Profile definition.
COL publicAccessDeviceConfigMode	1.3.6.1.4.1.8744.5.1.1.2.5	ColubrisUsersAuthenticationMode	read-only	Identifies how configuration of the device is performed. This can be via locally configured settings on the device, or retrieved from a AAA server. If both options are enabled, the settings retrieved from the AAA server overwrite the local configuration settings.
COL publicAccessDeviceAuthenProfileIndex	1.3.6.1.4.1.8744.5.1.1.2.6	ColubrisProfileIndexOrZero	read-only	Identifies the AAA server profile to use to authenticate the device. This attribute only applies when publicAccessDeviceConfigMode is set to 'profile' or 'localAndProfile'. When the special value zero is specified, no AAA server profile is selected.
INT publicAccessDeviceAccountingEnabled	1.3.6.1.4.1.8744.5.1.1.2.7	INTEGER	read-only	Identifies if accounting information is generated by the device and sent to the AAA server. The device generate RADIUS accounting of type ON and OFF. This also covers accounting of all access-lists independently of where they are used. For accounting, the following status types are generated: START, INTERIM-UPDATE, and STOP. Accounting information is generated only if a valid AAA server profile is configured in the publicAccessDeviceAccountingProfileIndex attribute.
COL publicAccessDeviceAccountingProfileIndex	1.3.6.1.4.1.8744.5.1.1.2.8	ColubrisProfileIndexOrZero	read-only	Identifies the AAA server profile to use for device accounting. This attribute only applies when publicAccessDeviceAccountingEnabled is set to 'enable'. When the special value zero is specified, the value set inside publicAccessDeviceAuthenProfileIndex is used instead.
INT publicAccessDeviceForceReconfiguration	1.3.6.1.4.1.8744.5.1.1.2.9	INTEGER	read-write	Specify forceReconfiguration(1) to force the device to re-read the local configuration file or re-issue an authentication request to the AAA server, or both based on the value of the publicAccessDeviceConfigMode attribute. Reading this object always returns 'idle'. Re-issuing an authentication only applies if a valid AAA server profile is specified in publicAccessDeviceAuthenProfileIndex.
publicAccessUsersGroup	1.3.6.1.4.1.8744.5.1.1.3
U32 publicAccessUsersMaxCount	1.3.6.1.4.1.8744.5.1.1.3.1	Unsigned32	read-only	Indicates the maximum number of concurrent authenticated users.
G32 publicAccessUsersCount	1.3.6.1.4.1.8744.5.1.1.3.2	Gauge32	read-only	Indicates the number of currently authenticated users.
U32 publicAccessUsersThreshold	1.3.6.1.4.1.8744.5.1.1.3.3	Unsigned32	read-write	Specifies the trigger value for sending the publicAccessUsersThresholdTrap. When the number of users logged into the public access interface is equal to or exceeds this threshold value, a publicAccessUsersThresholdTrap is sent. The threshold value cannot exceed publicAccessUsersMaxCount or an error is returned. Set this to zero to disable sending of the publicAccessUsersThresholdTrap.
COL publicAccessUsersSessionTrapEnabled	1.3.6.1.4.1.8744.5.1.1.3.4	ColubrisNotificationEnable	read-write	When set to enable, the publicAccessUsersSessionStart and publicAccessUsersSessionStop traps are generated when a user session begins or ends.
publicAccessUsersConfigTable	1.3.6.1.4.1.8744.5.1.1.3.5		not-accessible	Provides information on the user's authentication method. In tabular form to allow multiple instances on an agent.
publicAccessUsersConfigEntry	1.3.6.1.4.1.8744.5.1.1.3.5.1		not-accessible	An entry in the table.
I32 publicAccessUsersConfigIndex	1.3.6.1.4.1.8744.5.1.1.3.5.1.1	Integer32	not-accessible	Index of a user profile in the publicAccessUsersConfigTable.
COL publicAccessUsersConfigAuthenType	1.3.6.1.4.1.8744.5.1.1.3.5.1.2	ColubrisUsersAuthenticationType	read-only	Indicates the mechanism used to authenticate users.
COL publicAccessUsersConfigAuthenMode	1.3.6.1.4.1.8744.5.1.1.3.5.1.3	ColubrisUsersAuthenticationMode	read-only	Specifies how the user authentication is performed. It can be done with the local user list or via a AAA server profile. If both are enabled, the local user list is checked first.
COL publicAccessUsersConfigAuthenProfileIndex	1.3.6.1.4.1.8744.5.1.1.3.5.1.4	ColubrisProfileIndexOrZero	read-only	Specifies the AAA profile to use for user authentication when publicAccessUsersAuthenMode is set to 'profile' or 'localAndProfile'.
U32 publicAccessUsersConfigAuthenTimeout	1.3.6.1.4.1.8744.5.1.1.3.5.1.5	Unsigned32	read-only	Logins are refused if the AAA server does not respond within this time period. Only applies when coVirtualApUserAccessAuthenMode is set to 'profile' or 'localAndProfile' and when the users are authenticated via 'HTML' or 'MAC' authentication.
INT publicAccessUsersConfigAccountingEnabled	1.3.6.1.4.1.8744.5.1.1.3.5.1.6	INTEGER	read-only	Indicates if accounting information is generated by the device and sent to the AAA server for public access users. Accounting information is generated only if a valid AAA server profile is configured for publicAccessUsersAccountingProfileIndex.
COL publicAccessUsersConfigAccountingProfileIndex	1.3.6.1.4.1.8744.5.1.1.3.5.1.7	ColubrisProfileIndexOrZero	read-only	Identifies the AAA profile to send accounting to for public access users. When zero is specified, the value set inside publicAccessDeviceAuthenProfileIndex is used instead.
NUM publicAccessUsersConfigInterfaceIndex	1.3.6.1.4.1.8744.5.1.1.3.5.1.8	InterfaceIndex	read-only	Indicates the local interface on which these configuration parameters apply. This attribute is used with the publicAccessUsersConfigVirtualApProfileIndex to uniquely identify an entry in Virtual AP indexed tables.
I32 publicAccessUsersConfigVirtualApProfileIndex	1.3.6.1.4.1.8744.5.1.1.3.5.1.9	Integer32	read-only	Indicates a user's VAP profile currently associated with these configuration parameters. This attribute is used with the publicAccessUsersConfigInterfaceIndex to uniquely identify an entry in Virtual AP indexed tables.
publicAccessUserTable	1.3.6.1.4.1.8744.5.1.1.3.6		not-accessible	A table containing specific information for users authenticated by the authentication system. In tabular form to allow multiple instances on an agent.
publicAccessUserEntry	1.3.6.1.4.1.8744.5.1.1.3.6.1		not-accessible	Information about a particular user that has been authenticated by the authentication system. publicAccessUserIndex - Uniquely identifies a user in the table.
I32 publicAccessUserIndex	1.3.6.1.4.1.8744.5.1.1.3.6.1.1	Integer32	not-accessible	Index of a user in the publicAccessUserTable.
COL publicAccessUserAuthenType	1.3.6.1.4.1.8744.5.1.1.3.6.1.2	ColubrisUsersAuthenticationType	read-only	Indicates the mechanism used to authenticate the user.
COL publicAccessUserAuthenMode	1.3.6.1.4.1.8744.5.1.1.3.6.1.3	ColubrisUsersAuthenticationMode	read-only	Specifies how user authentication is performed. It can be done using a local user list defined on the device or AAA server profile. If both modes are active the local user list is checked first.
INT publicAccessUserState	1.3.6.1.4.1.8744.5.1.1.3.6.1.4	INTEGER	read-only	Indicates the current state of the user.
IP publicAccessUserStationIpAddress	1.3.6.1.4.1.8744.5.1.1.3.6.1.5	IpAddress	read-only	Indicates the user's IP address.
OCT publicAccessUserName	1.3.6.1.4.1.8744.5.1.1.3.6.1.6	OCTET STRING	read-only	Indicates the user's name.
DAT publicAccessUserSessionStartTime	1.3.6.1.4.1.8744.5.1.1.3.6.1.7	DateAndTime	read-only	Indicates when this user session was started.
C32 publicAccessUserSessionDurationEx	1.3.6.1.4.1.8744.5.1.1.3.6.1.8	Counter32	read-only	Indicates how long the user's session has been active. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C32 publicAccessUserIdleTime	1.3.6.1.4.1.8744.5.1.1.3.6.1.9	Counter32	read-only	Indicates for how long the user's session has been idle. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C64 publicAccessUserBytesSent	1.3.6.1.4.1.8744.5.1.1.3.6.1.10	Counter64	read-only	Indicates the total number of bytes sent by the user. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C64 publicAccessUserBytesReceived	1.3.6.1.4.1.8744.5.1.1.3.6.1.11	Counter64	read-only	Indicates the total number of bytes received by the user. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C32 publicAccessUserPacketsSent	1.3.6.1.4.1.8744.5.1.1.3.6.1.12	Counter32	read-only	Indicates the total number of IP packets sent by the user. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C32 publicAccessUserPacketsReceived	1.3.6.1.4.1.8744.5.1.1.3.6.1.13	Counter32	read-only	Indicates the total number of IP packets received by the user. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
INT publicAccessUserForceDisconnection	1.3.6.1.4.1.8744.5.1.1.3.6.1.14	INTEGER	read-write	Setting this attribute to 'adminReset' disconnects the user with a cause of ADMIN_RESET. Reading this variable always return 'idle'.
MAC publicAccessUserStationMacAddress	1.3.6.1.4.1.8744.5.1.1.3.6.1.15	MacAddress	read-only	Indicates the user's MAC Address.
MAC publicAccessUserApMacAddress	1.3.6.1.4.1.8744.5.1.1.3.6.1.16	MacAddress	read-only	Indicates the user's Access Point MAC Address when Location- Aware is enabled or the Access Controller MAC Address.
OCT publicAccessUserGroupName	1.3.6.1.4.1.8744.5.1.1.3.6.1.17	OCTET STRING	read-only	Indicates the user's Access Point Group Name (ONLY when Location-aware is enabled and properly configured). If this information is not available, a zero-Length string is returned.
COL publicAccessUserSSID	1.3.6.1.4.1.8744.5.1.1.3.6.1.18	ColubrisSSIDOrNone	read-only	Indicates the user's Access Point SSID (ONLY when Location-aware is enabled and properly configured). If this information is not available, a zero-Length string is returned.
COL publicAccessUserSecurity	1.3.6.1.4.1.8744.5.1.1.3.6.1.19	ColubrisSecurity	read-only	Specifies the user's security mode.
INT publicAccessUserPHYType	1.3.6.1.4.1.8744.5.1.1.3.6.1.20	INTEGER	read-only	Specifies the user's radio type.
I32 publicAccessUserVLAN	1.3.6.1.4.1.8744.5.1.1.3.6.1.21	Integer32	read-only	Specifies the VLAN currently assigned to the user.
I32 publicAccessUserApRadioIndex	1.3.6.1.4.1.8744.5.1.1.3.6.1.22	Integer32	read-only	Indicates the radio to which this user is associated. The index 0 is reserved when location aware is not enabled or not properly configured. It means that the system could not determine on which interface the user is connected. Please note that this information is not related to the standard SNMP interface table. It is a proprietary index information on the Radios in Colubris devices.
I32 publicAccessUserConfigIndex	1.3.6.1.4.1.8744.5.1.1.3.6.1.23	Integer32	read-only	Indicates the configuration profile in the publicAccessUsersConfigTable currently associated with this user. When location aware is not enabled or not properly configured, the first SSID of the first radio interface is used as the default configuration profile.
OCT publicAccessUserConnectedInterface	1.3.6.1.4.1.8744.5.1.1.3.6.1.24	OCTET STRING	accessible-for-notify	Indicates the device's logical public interface to which the user is connected. This will always be a string containing 'br0'.
C64 publicAccessUserBytesSentDropped	1.3.6.1.4.1.8744.5.1.1.3.6.1.25	Counter64	read-only	Indicates the total number of bytes sent by the user and dropped due to rate limitation. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C64 publicAccessUserBytesReceivedDropped	1.3.6.1.4.1.8744.5.1.1.3.6.1.26	Counter64	read-only	Indicates the total number of bytes received for the user and dropped due to rate limitation. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C32 publicAccessUserPacketsSentDropped	1.3.6.1.4.1.8744.5.1.1.3.6.1.27	Counter32	read-only	Indicates the total number of packets sent by the user and dropped due to rate limitation. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
C32 publicAccessUserPacketsReceivedDropped	1.3.6.1.4.1.8744.5.1.1.3.6.1.28	Counter32	read-only	Indicates the total number of packets received for the user and dropped due to rate limitation. When this counter reaches its maximum value, it wraps around and starts increasing again from zero.
T/F publicAccessUserRateLimitationEnabled	1.3.6.1.4.1.8744.5.1.1.3.6.1.29	TruthValue	read-only	Specifies if rate limitation is enabled for the user.
I32 publicAccessUserMaxTransmitRate	1.3.6.1.4.1.8744.5.1.1.3.6.1.30	Integer32	read-only	Specifies the maximum transmit rate for the user.
I32 publicAccessUserMaxReceiveRate	1.3.6.1.4.1.8744.5.1.1.3.6.1.31	Integer32	read-only	Specifies the maximum receive rate for the user.
COL publicAccessUserBandwidthControlLevel	1.3.6.1.4.1.8744.5.1.1.3.6.1.32	ColubrisPriorityQueue	read-only	Specifies the user's bandwidth control level.
U32 publicAccessUserNASPort	1.3.6.1.4.1.8744.5.1.1.3.6.1.33	Unsigned32	read-only	Specifies the NAS-Port value assigned to the user.
COL publicAccessUsersLoggedInTrapEnabled	1.3.6.1.4.1.8744.5.1.1.3.7	ColubrisNotificationEnable	read-write	When set to enable, the publicAccessUsersLoggedInTrap is generated.
U32 publicAccessUsersLoggedInTrapInterval	1.3.6.1.4.1.8744.5.1.1.3.8	Unsigned32	read-write	Interval between publicAccessUsersLoggedInTrap traps. Setting this to 0 will disable periodic sending of these traps.
publicAccessNASPortsGroup	1.3.6.1.4.1.8744.5.1.1.4
G32 publicAccessNASPortCount	1.3.6.1.4.1.8744.5.1.1.4.1	Gauge32	read-only	Indicates the number of NAS-Port supported.
publicAccessNASPortTable	1.3.6.1.4.1.8744.5.1.1.4.2		not-accessible	A table containing specific information for NAS-Port by the Access Controller. In tabular form to allow multiple instances on an agent.
publicAccessNASPortEntry	1.3.6.1.4.1.8744.5.1.1.4.2.1		not-accessible	Information about a particular NAS-Port by Access Controller. publicAccessNASPortIndex - Uniquely identifies a NAS-Port in the table.
I32 publicAccessNASPortIndex	1.3.6.1.4.1.8744.5.1.1.4.2.1.1	Integer32	not-accessible	Index of a NAS-Port in the publicAccessNASPortTable.
OCT publicAccessNASPortUserName	1.3.6.1.4.1.8744.5.1.1.4.2.1.2	OCTET STRING	read-only	Indicates the user's name currently authenticated by the Access Controller on this NAS-Port.
publicAccessMIBNotificationPrefix	1.3.6.1.4.1.8744.5.1.2
publicAccessMIBNotifications	1.3.6.1.4.1.8744.5.1.2.0
NTF publicAccessStatusChangedTrap	1.3.6.1.4.1.8744.5.1.2.0.1			This notification is sent whenever the authentication system status changes (up or down).
NTF publicAccessUsersThresholdTrap	1.3.6.1.4.1.8744.5.1.2.0.2			This notification is sent whenever publicAccessUsersThreshold is exceeded.
NTF publicAccessUsersSessionStartTrap	1.3.6.1.4.1.8744.5.1.2.0.3			When a user successfully authenticate a trap is generated if the publicAccessUsersSessionTrapEnabled is set to True.
NTF publicAccessUsersSessionStopTrap	1.3.6.1.4.1.8744.5.1.2.0.4			When a user terminates their session a trap is generated if the publicAccessUsersSessionTrapEnabled is set to True.
NTF publicAccessUsersSessionFailTrap	1.3.6.1.4.1.8744.5.1.2.0.5			When a user authentication fails a trap is generated if the publicAccessUsersSessionTrapEnabled is set to True.
NTF publicAccessUsersLoggedInTrap	1.3.6.1.4.1.8744.5.1.2.0.6			This is sent when a user is authenticated or periodically (see publicAccessUSersLoggedInTrapInterval) if the publicAccessUsersLoggedInTrapEnabled is set to True.
colubrisPublicAccessMIBConformance	1.3.6.1.4.1.8744.5.1.3
colubrisPublicAccessMIBCompliances	1.3.6.1.4.1.8744.5.1.3.1
colubrisPublicAccessMIBCompliance	1.3.6.1.4.1.8744.5.1.3.1.1			The compliance statement for entities which implement the Colubris Public Access MIB.
colubrisPublicAccessMIBGroups	1.3.6.1.4.1.8744.5.1.3.2
colubrisPublicAccessMIBGroup	1.3.6.1.4.1.8744.5.1.3.2.1			A collection of objects providing control over the Public Access MIB.
colubrisPublicAccessUserMIBGroup	1.3.6.1.4.1.8744.5.1.3.2.2			A collection of objects providing the Public Access MIB capability.
colubrisPublicAccessUserConfigMIBGroup	1.3.6.1.4.1.8744.5.1.3.2.3			A collection of objects providing the Public Access user configuration capability.
colubrisPublicAccessNotificationGroup	1.3.6.1.4.1.8744.5.1.3.2.4			A collection of supported notifications.
colubrisPublicAccessNASPortsMIBGroup	1.3.6.1.4.1.8744.5.1.3.2.5			A collection of objects providing the Public Access NAS Port MIB capability.

RFC description

Manages public access authentication systems and user access controls for Colubris wireless networks.

Start monitoring Colubris/HP wireless access point/gateway (hotspot, legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download COLUBRIS-PUBLIC-ACCESS-MIB