All MIBs › HP700RX-MIB
Category: Hardware and Environment, Vendor: HP/HPE
Description: SNMP MIB for the HP 700/RX X terminal providing management objects for monitor, memory, serial port, and network configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP700RX-MIB?
HP700RX-MIB is a legacy, vendor-specific MIB for the HP 700/RX series X terminal, an older thin-client/X-Windows terminal device rather than a modern network switch, dating from an earlier era of HP networked hardware. It exposes management objects grouped under headings like monitor, memory, serial port (nm/system/interface), and network configuration (icmp, snmp), reflecting the device's role as a simple network-attached terminal. Its monitoring focus is on basic hardware and software status of the terminal itself, such as monitor/display configuration, memory usage, and network/ICMP/SNMP interface health, useful for administrators managing fleets of these terminals in the era they were deployed. It builds directly on standard MIB-II conventions (system, interface, icmp, snmp groups) as its base structure, with the hp-specific 'nm' group layered on top for terminal-specific management. It was typically deployed in legacy enterprise or educational computing environments using HP 700/RX X terminals connected to Unix hosts. Network engineers evaluating or troubleshooting this functionality can download the HP700RX-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP700RX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP 700/RX X terminal (legacy thin client)
Monitoring Examples
An administrator managing a fleet of HP 700/RX terminals would poll objects under the 'system' and 'interface' groups (following standard MIB-II conventions) alongside the HP-specific 'nm' group to check terminal memory usage and monitor/display settings. Anomalies in the interface or icmp groups would reveal network connectivity problems between the terminal and its host, while the 'nm' group's memory-related objects would reveal resource exhaustion on the terminal.
What Can Be Monitored
- terminal memory usage
- monitor/display configuration
- serial/network interface status
- ICMP statistics
- SNMP agent status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1065-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT accessControls | 1.3.6.1.4.1.11.2.3.9.3.1.5.2 | INTEGER | read-write | This determines whether host access controls are used by the server during client connection. If enabled, only those clients running on hosts listed in the terminal's access control file will be allowed to connect to the X server. This file is read from the host using the path /usr/tftpdir/usr/lib/X11/700X/etc/ipaddress.hosts. |
| INT alternateAccessMethod | 1.3.6.1.4.1.11.2.3.9.3.1.2.8 | INTEGER | read-write | The method used to read files from the alternative file server. This method may be overridden for individual pathes. |
| STR alternateFileServer | 1.3.6.1.4.1.11.2.3.9.3.1.2.7 | DisplayString | read-write | The address of the file server the terminal will attempt to contact at startup if the primary file server cannot be reached. This address may be the node name (in which case it will be resolved to an address before use using the Domain Name Resolution) or it may be the address in dotted decimal form. |
| STR alternateNameServer | 1.3.6.1.4.1.11.2.3.9.3.1.2.11 | DisplayString | read-write | The alternative name server's IP address in dotted decimal format. If no answer is received from the primary name server, the terminal attempts to contact this name server. |
| INT at2kbLanguage | 1.3.6.1.4.1.11.2.3.9.3.1.1.4 | INTEGER | read-write | The language setting for an AT/2 keyboard attached to this terminal. |
| INT at2kbLEDControl | 1.3.6.1.4.1.11.2.3.9.3.1.1.3 | INTEGER | read-write | Indicates whether the CAPS-LOCK LED on the keyboard (if present) is controlled by the X terminal or the clients (as X LED 3). |
| INT bootFileFrom | 1.3.6.1.4.1.11.2.3.9.3.1.3.3 | INTEGER | read-write | Controls whether or not the X server file is read from the ROM card (if present). |
| STR bootFileName | 1.3.6.1.4.1.11.2.3.9.3.1.3.4 | DisplayString | read-write | The name of the X server file to load. This may be a complete path (starting with /) and may include host and access method overrides. |
| INT clientAuthentication | 1.3.6.1.4.1.11.2.3.9.3.1.5.1 | INTEGER | read-write | Controls whether MIT-MAGIC-COOKIE authentication is used by the server during client connection. If enabled, the client must pass a valid MAGIC_COOKIE to the server during the connection sequence. This feature can only be used with XDMCP enabled. |
| config | 1.3.6.1.4.1.11.2.3.9.3.1 | |||
| STR configedAddress | 1.3.6.1.4.1.11.2.3.9.3.1.2.2 | DisplayString | read-write | The IP address configured for the Ethernet interface on this terminal. The active value for this field is set at startup. After startup a different value can be saved to terminal memory without being used, therefore the value returned via SNMP is not necessarily the value currently in use. |
| configedRouteTable | 1.3.6.1.4.1.11.2.3.9.3.1.2.4 | not-accessible | The routes configured for this terminal. At startup the terminal tests the routes in its routing table. If any route fails, it will be discarded, therefore the configured routes may not be the routes in use. There are a number of ways a route can fail the startup tests, including: terminal can't ping the gateway, terminal can't resolve one of the names into an IP address, or a specified gateway is not on a connected subnet. | |
| STR configedSubnetMask | 1.3.6.1.4.1.11.2.3.9.3.1.2.3 | DisplayString | read-write | The subnet mask configured for the Ethernet interface on this terminal. The active value for this field is set at startup. After startup a different value can be saved to terminal memory without being used, therefore the value returned via SNMP is not necessarily the value currently in use. |
| STR domain | 1.3.6.1.4.1.11.2.3.9.3.1.2.12 | DisplayString | read-write | The fully qualified domain of the network to which the terminal is connected. This includes all parts following the first '.' (dot) in the fully qualified host name of the terminal. Typical examples are hp.com or waterloo.edu |
| CTR etherInAlignErrors | 1.3.6.1.4.1.11.2.3.9.3.1.4.33 | Counter | read-only | The number of packets received on the Ethernet interface that were not an integral number of octets in length. |
| CTR etherInCollisions | 1.3.6.1.4.1.11.2.3.9.3.1.4.34 | Counter | read-only | The number of collisions detected on the Ethernet interface that were after the start of the normal packet. |
| CTR etherInCRCErrors | 1.3.6.1.4.1.11.2.3.9.3.1.4.14 | Counter | read-only | The number of CRC errors detected in Ethernet packets. |
| CTR etherInNoBuffers | 1.3.6.1.4.1.11.2.3.9.3.1.4.15 | Counter | read-only | The number of time the Ethernet interface hardware could not receive packets because no buffers were available. |
| CTR etherInOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.17 | Counter | read-only | The number of octets received on the Ethernet interface. |
| CTR etherInPackets | 1.3.6.1.4.1.11.2.3.9.3.1.4.13 | Counter | read-only | The number of packets received over Ethernet. |
| CTR etherInRunts | 1.3.6.1.4.1.11.2.3.9.3.1.4.16 | Counter | read-only | The number of packets received on the Ethernet interface that were shorter then the shortest permitted packet. |
| CTR etherOutMaxCollisions | 1.3.6.1.4.1.11.2.3.9.3.1.4.22 | Counter | read-only | The number of times that the Ethernet interface was unable to transmit a packet due to too many collisions. |
| CTR etherOutMoreCollisions | 1.3.6.1.4.1.11.2.3.9.3.1.4.21 | Counter | read-only | The number of messages for which the Ethernet interface had to back off more then twice (but less then the maximum number of times) due to collisions. |
| CTR etherOutNoBuffers | 1.3.6.1.4.1.11.2.3.9.3.1.4.23 | Counter | read-only | The number of times that the Ethernet interface software had to drop an outbound packet because there were no more interface transmit buffers. |
| CTR etherOutOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.24 | Counter | read-only | The number of octets sent out the Ethernet interface. |
| CTR etherOutOneCollisions | 1.3.6.1.4.1.11.2.3.9.3.1.4.19 | Counter | read-only | The number of times the Ethernet interface had to back off once due to a collision. |
| CTR etherOutPackets | 1.3.6.1.4.1.11.2.3.9.3.1.4.18 | Counter | read-only | The number of packets sent out the Ethernet interface. |
| CTR etherOutTwoCollisions | 1.3.6.1.4.1.11.2.3.9.3.1.4.20 | Counter | read-only | The number of times the Ethernet interface had to back off twice due to collisions. |
| INT fileTimeout | 1.3.6.1.4.1.11.2.3.9.3.1.2.9 | INTEGER | read-write | The maximum time (in seconds) that the terminal will wait for a response to a request to the file server before giving up. The name resolver timeout is six times the file timeout. |
| fontEntry | 1.3.6.1.4.1.11.2.3.9.3.1.3.13.1 | not-accessible | An single path to a set of font files. | |
| INT fontIndex | 1.3.6.1.4.1.11.2.3.9.3.1.3.13.1.1 | INTEGER | read-only | The index into the list of font paths. |
| STR fontPath | 1.3.6.1.4.1.11.2.3.9.3.1.3.13.1.2 | DisplayString | read-write | The actual font path in the format appropriate to the operating system in use. |
| fontPathTable | 1.3.6.1.4.1.11.2.3.9.3.1.3.13 | not-accessible | A list of directory paths used when by the X server when searching for fonts | |
| hp | 1.3.6.1.4.1.11 | |||
| hpXStation | 1.3.6.1.4.1.11.2.3.9.3 | |||
| icmp | 1.3.6.1.4.1.11.2.7 | |||
| interface | 1.3.6.1.4.1.11.2.4 | |||
| INT memBackingstore | 1.3.6.1.4.1.11.2.3.9.3.1.4.6 | INTEGER | read-only | The amount of memory used for backingstore in Kbytes. |
| INT memFrags | 1.3.6.1.4.1.11.2.3.9.3.1.4.4 | INTEGER | read-only | The number of fragments (of all sizes) in the memory free pool. |
| INT memFree | 1.3.6.1.4.1.11.2.3.9.3.1.4.2 | INTEGER | read-only | The amount of memory in the free pool (including free video memory). This is the total amount of memory that is not currently in use in the terminal. |
| INT memInstalled | 1.3.6.1.4.1.11.2.3.9.3.1.4.1 | INTEGER | read-only | The amount of memory installed in the terminal (excluding video memory) in Kbytes. |
| INT memLargestFrag | 1.3.6.1.4.1.11.2.3.9.3.1.4.5 | INTEGER | read-only | The size of the largest fragment in the free pool in Kbytes. This represents the largest request for memory that can be fulfilled by the terminal. |
| INT memLowMark | 1.3.6.1.4.1.11.2.3.9.3.1.4.3 | INTEGER | read-only | The size of the free pool at its smallest since the last time this counter was reset. |
| CTR memReclaims | 1.3.6.1.4.1.11.2.3.9.3.1.4.7 | Counter | read-only | The number of times memory has been reclaimed from backing store for other uses. |
| INT monitor | 1.3.6.1.4.1.11.2.3.9.3.1.1.1 | INTEGER | read-write | The type of monitor the terminal is configured to drive. Each monitor type varies in resolution, refresh rate, color capability, dots per inch, and synchronization. Some monitors (especially multi-sync types) may produce usable displays at several settings. |
| STR monitorDescription | 1.3.6.1.4.1.11.2.3.9.3.1.1.2 | DisplayString | read-only | The resolution, refresh rate, color capability, dots per inch, and synchronization the terminal is sending to its monitor and the part number of the monitor that works best at these settings. |
| netPeripherals | 1.3.6.1.4.1.11.2.3.9 | |||
| network | 1.3.6.1.4.1.11.2.3.9.3.1.2 | |||
| INT networkParamsFrom | 1.3.6.1.4.1.11.2.3.9.3.1.2.1 | INTEGER | read-write | Indicates whether the X terminal will use bootp to get its network parameters (IP address, default gateway, boot file, terminal name, domain name, name server addresses, subnet mask, and remote configuration file) at power up or use those stored in EEPROM. |
| nm | 1.3.6.1.4.1.11.2 | |||
| CTR parallelErrors | 1.3.6.1.4.1.11.2.3.9.3.1.4.12 | Counter | read-only | The number of errors detected in sending data out the parallel port since the last time this counter was reset. |
| CTR parallelOutOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.11 | Counter | read-only | The number of octets sent out the parallel port since the last time this counter was reset. |
| INT parallelUse | 1.3.6.1.4.1.11.2.3.9.3.1.1.11 | INTEGER | read-write | What the parallel port is being used for. Note that primary and auxiliary use indicate that the serial port is 'connected' to TCP ports 9100 and 9101 respectively. |
| INT portuseEnable | 1.3.6.1.4.1.11.2.3.9.3.1.1.12 | INTEGER | read-write | This variable indicates whether remote (through SNMP) serial port use changes are allowed. |
| preferences | 1.3.6.1.4.1.11.2.3.9.3.1.5 | |||
| INT primaryAccessMethod | 1.3.6.1.4.1.11.2.3.9.3.1.2.6 | INTEGER | read-write | The method used to read files from the primary file server. This method may be overridden for individual paths. |
| STR primaryFileServer | 1.3.6.1.4.1.11.2.3.9.3.1.2.5 | DisplayString | read-write | The address of the first file server the terminal attempts to contact at startup. This may be either a node name (in which case it will be resolved to an address using Domain Name Resolution) or it may be an IP address in dotted decimal form. |
| STR primaryNameServer | 1.3.6.1.4.1.11.2.3.9.3.1.2.10 | DisplayString | read-write | The primary name server's IP address in dotted decimal format. |
| INT r3BugCompatability | 1.3.6.1.4.1.11.2.3.9.3.1.5.3 | INTEGER | read-write | This determines whether the server behaves like an X11R3 server for certain specific operations. |
| INT reboot | 1.3.6.1.4.1.11.2.3.9.3.1.6.2 | INTEGER | read-write | Setting this variable to zero will cause the X terminal to reset. |
| INT remoteConfigEnabled | 1.3.6.1.4.1.11.2.3.9.3.1.3.5 | INTEGER | read-write | Controls whether or not the remote config file is read from the file server at startup. |
| STR remoteConfigFile | 1.3.6.1.4.1.11.2.3.9.3.1.3.6 | DisplayString | read-write | The name of the remote config file to load at startup. This may be a complete path (starting with /) and include host and access method overrides. |
| reset | 1.3.6.1.4.1.11.2.3.9.3.1.6 | |||
| INT resetEnable | 1.3.6.1.4.1.11.2.3.9.3.1.6.1 | INTEGER | read-write | This variable indicates whether remote (through SNMP) resets are allowed. |
| INT rgbFileFrom | 1.3.6.1.4.1.11.2.3.9.3.1.3.2 | INTEGER | read-write | Controls whether or not the rgb.txt file is read from the ROM card (if present). |
| INT romFonts | 1.3.6.1.4.1.11.2.3.9.3.1.3.1 | INTEGER | read-write | Controls whether or not fonts are read from the ROM card (if present). |
| STR routeDestination | 1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.3 | DisplayString | read-write | The final destination address for this route. This may be a machine or a network. Note that this is a string and may be either a dotted decimal IP address or a domain name. |
| STR routeGateway | 1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.2 | DisplayString | read-write | The address of an intermediate machine to send packets to. Note that this is a string and may be either a dotted decimal IP address or a domain name. |
| INT routeIndex | 1.3.6.1.4.1.11.2.3.9.3.1.2.4.1.1 | INTEGER | read-only | The number of a row in the gateway table on the Network config screen. |
| routeTableEntry | 1.3.6.1.4.1.11.2.3.9.3.1.2.4.1 | not-accessible | Each entry reflects one route. | |
| INT serialDataBits | 1.3.6.1.4.1.11.2.3.9.3.1.1.6 | INTEGER | read-write | The number of data bits in each character sent and received over the serial port. |
| CTR serialInErrors | 1.3.6.1.4.1.11.2.3.9.3.1.4.10 | Counter | read-only | The number of errors detected on data received in the serial port. |
| CTR serialInOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.8 | Counter | read-only | The number of octets received through the serial port since the last time this counter was reset. |
| CTR serialOutOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.9 | Counter | read-only | The number of octets sent out the serial port since The last time this counter was reset. |
| INT serialPacing | 1.3.6.1.4.1.11.2.3.9.3.1.1.9 | INTEGER | read-write | The type of flow control used on the serial port. |
| INT serialParity | 1.3.6.1.4.1.11.2.3.9.3.1.1.8 | INTEGER | read-write | The parity generated and checked on each character sent and received through the serial port. |
| INT serialSpeed | 1.3.6.1.4.1.11.2.3.9.3.1.1.5 | INTEGER | read-write | The baud rate of the serial port. |
| INT serialStopBits | 1.3.6.1.4.1.11.2.3.9.3.1.1.7 | INTEGER | read-write | The number of stop bits sent at the end of each character sent through the serial port. |
| INT serialUse | 1.3.6.1.4.1.11.2.3.9.3.1.1.10 | INTEGER | read-write | What the serial port is being used for. Note that primary and auxiliary use indicate that the serial port is 'connected' to TCP ports 9100 and 9101 respectively. |
| CTR slipInErrs | 1.3.6.1.4.1.11.2.3.9.3.1.4.29 | Counter | read-only | The number of errors encountered on received octets on the serial interface while running SLIP. |
| CTR slipInOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.28 | Counter | read-only | The number of octets received over the serial interface while running SLIP. |
| CTR slipInPackets | 1.3.6.1.4.1.11.2.3.9.3.1.4.27 | Counter | read-only | The number of packets received over the serial interface while running SLIP. |
| STR slipLocalAddress | 1.3.6.1.4.1.11.2.3.9.3.1.2.14 | DisplayString | read-write | The address used for the terminal end of the SLIP connection. |
| STR slipMask | 1.3.6.1.4.1.11.2.3.9.3.1.2.16 | DisplayString | read-write | The subnet mask configured for the SLIP interface on this terminal. |
| CTR slipOutErrors | 1.3.6.1.4.1.11.2.3.9.3.1.4.32 | Counter | read-only | The number of errors encountered while transmitting over the serial interface while running SLIP. |
| CTR slipOutOctets | 1.3.6.1.4.1.11.2.3.9.3.1.4.31 | Counter | read-only | The number of octets transmitted over the serial interface while running SLIP. |
| CTR slipOutPackets | 1.3.6.1.4.1.11.2.3.9.3.1.4.30 | Counter | read-only | The number of packets transmitted over the serial interface while running SLIP. |
| STR slipRemoteAddress | 1.3.6.1.4.1.11.2.3.9.3.1.2.15 | DisplayString | read-write | The address used for the remote (host) end end of the SLIP connection. |
| snmp | 1.3.6.1.4.1.11.2.13 | |||
| snmpdConf | 1.3.6.1.4.1.11.2.13.2 | |||
| startup | 1.3.6.1.4.1.11.2.3.9.3.1.3 | |||
| statistics | 1.3.6.1.4.1.11.2.3.9.3.1.4 | |||
| TIK statsTime | 1.3.6.1.4.1.11.2.3.9.3.1.4.26 | TimeTicks | read-only | The statistics information can be cleared (to zero) by depressing a button on the statistics screen. This variable indicates the time since this was last done. It is the amount of time over which statistics have been collected. |
| system | 1.3.6.1.4.1.11.2.3 | |||
| INT telnetAutoStart | 1.3.6.1.4.1.11.2.3.9.3.1.3.10 | INTEGER | read-write | Determines whether a TELNET session is auto- started at boot time. TELNET can be used to start a user session, but TELNET cannot be used if XDMCP is enabled. |
| INT telnetCharSet | 1.3.6.1.4.1.11.2.3.9.3.1.3.11 | INTEGER | read-write | Controls the character set used to display characters in the TELNET and serial terminal sessions. |
| STR telnetHost | 1.3.6.1.4.1.11.2.3.9.3.1.3.12 | DisplayString | read-write | The address of the host to attempt to connect to when TELNET is (auto)started. This may be a name or IP address in dotted decimal format. |
| terminal | 1.3.6.1.4.1.11.2.3.9.3.1.1 | |||
| STR terminalName | 1.3.6.1.4.1.11.2.3.9.3.1.2.13 | DisplayString | read-write | The name assigned to this terminal. This name should correspond to the name assigned using the Domain Name service, Network Information Services, and other host address lookup mechanisms. |
| CTR tftpTimeouts | 1.3.6.1.4.1.11.2.3.9.3.1.4.25 | Counter | read-only | The number of times that the tftp driver has not gotten a response within the file timeout period. This is not the number of retransmits performed by the tftp driver but is the number of completely failed requests. |
| trap | 1.3.6.1.4.1.11.2.13.1 | |||
| INT xdmcpEnabled | 1.3.6.1.4.1.11.2.3.9.3.1.3.7 | INTEGER | read-write | Controls whether or not XDMCP is used to start user sessions on this terminal. |
| STR xdmcpHost | 1.3.6.1.4.1.11.2.3.9.3.1.3.9 | DisplayString | read-write | The address of the host to which the terminal sends XDMCP requests at startup. This field is ignored if XDMCP type is BROADCAST. |
| INT xdmcpType | 1.3.6.1.4.1.11.2.3.9.3.1.3.8 | INTEGER | read-write | Controls the type of XDMCP request sent from the terminal at startup. |
RFC description
Configures HP 700RX terminal display, network, and system preference parameters.
Start monitoring Legacy HP 700/RX X terminal (thin client) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.