GANDALF-ENTERPRISE-MIB

All MIBs › GANDALF-ENTERPRISE-MIB

Category: Domain: WAN, Vendor: Gandalf

Description: Gandalf Technologies enterprise MIB providing OID registrations and management objects for WAN networking products.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GANDALF-ENTERPRISE-MIB?

GANDALF-ENTERPRISE-MIB is a legacy Gandalf Technologies (enterprise OID 64) proprietary MIB reporting hub/card inventory and status. Its objects cover a hub basic ID (Ethernet MAC address), card capacity, card map, relay count/active flags, resource type, standard revision, IEEE 802.3 LME options, manufacturer/product ID/version/phone, hub name/IP address, EEPROM revision, secure-mode flag, and a basic-card table (ID, port count, name, type, ring number A/B, IBM-mode flag). As a hardware-status MIB it lets an administrator confirm card inventory and hub identity on a legacy Gandalf Technologies hub. It is deployed on legacy Gandalf Technologies hub equipment. Engineers can download the GANDALF-ENTERPRISE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GANDALF-ENTERPRISE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Legacy Gandalf Technologies hub equipment

Monitoring Examples

An administrator checks hubCardMap and gCardType to confirm card inventory on a legacy Gandalf Technologies hub.

What Can Be Monitored

hub/card hardware inventory and identity

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
gandalf	1.3.6.1.4.1.64
NTF gCardInstalled	1.3.6.1.4.1.64.0.100			This trap indicates that a card was physically installed in the hub. The trap description identify the card slot number.
NTF gCardRemoved	1.3.6.1.4.1.64.0.101			This trap indicates that a card was physically removed from the hub. The trap description identify the card slot number.
NTF gCardMismatch	1.3.6.1.4.1.64.0.102			This trap indicates that a card was physically installed in a slot configured with a different card type.
NTF gCardMismatchCleared	1.3.6.1.4.1.64.0.103			This trap indicates that the slot causing a Card Mismatch was reconfigured with the proper card type.
NTF gPortThresholdExceeded	1.3.6.1.4.1.64.0.104			This trap indicates a time based or frame based threshold is exceeded on a given port. The trap description will indicate the type of threshold, as well as identifing the card and port number.
NTF gNvramFault	1.3.6.1.4.1.64.0.105			This trap indicates a critical hardware failure: an NVRAM fault.
NTF gFiltDatabaseFull	1.3.6.1.4.1.64.0.106			This trap indicates that the number of entries in the Filtering Database has reached the bridge's storing capacity.
NTF gPowerSupplyFailed	1.3.6.1.4.1.64.0.107			This trap indicates that a fault was detected on a power supply. The trap description will indicate which of the two power supply is faulty.
NTF gLogThresholdExceeded	1.3.6.1.4.1.64.0.108			This trap indicates that the event log capacity was exceeded.
NTF gLinkMismatch	1.3.6.1.4.1.64.0.109			This trap indicates that the configuration of a WAN port is incompatible with the network topology.
NTF gLinkMismatchCleared	1.3.6.1.4.1.64.0.110			This trap indicates that the condition causing a Link Mismatch was corrected.
NTF gNewRoot	1.3.6.1.4.1.64.0.111			The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election.
NTF gTopologyChange	1.3.6.1.4.1.64.0.112			A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition.
NTF gPortFailure	1.3.6.1.4.1.64.0.113			A link to a port has failed. Possible reasons: 1. Master port idle receive timer has expired. Port has been disabled and declared faulty. Standby port will take over if ready. 2. Standby port idle receive timer has expired. Port has been disabled and declared faulty.
gandalf_hub	1.3.6.1.4.1.64.1
hmBasicCapability	1.3.6.1.4.1.64.1.1
OCT hubBasicID	1.3.6.1.4.1.64.1.1.1	OCTET STRING	read-only	A 48-bit unique identifier, the hub ethernet address is used.
INT hubCardCapacity	1.3.6.1.4.1.64.1.1.2	INTEGER	read-only	The number of groups (cards) that can be contained within the hub.
OCT hubCardMap	1.3.6.1.4.1.64.1.1.3	OCTET STRING	read-only	A string of bits which reflects the current configuration of units which are viewed by the Group managed objects. The length of the bitstring is hubGroupCapacity bits. The LSBit relates to the unit viewed by group 1. A '1' in the bitstring indicates presence of the unit, '0' represent absence of the unit.
INT hubNumOfRelays	1.3.6.1.4.1.64.1.1.4	INTEGER	read-only	Shows the number of relays present without regard as to whether or not each is enabled or disabled.
INT hubRelayActive	1.3.6.1.4.1.64.1.1.5	INTEGER	read-only	An integer that indicates which relay is active. Zero indicates that no relays are active.
INT hubResourceType	1.3.6.1.4.1.64.1.1.6	INTEGER	read-only	An integer value representing the IEEE802 Standard that applies to this resource.
INT hubStandardRevision	1.3.6.1.4.1.64.1.1.7	INTEGER	read-only	An integer value representing the revision of the IEEE802 Standard to which the station conforms with respect to that resource.
OCT hubIEEE8023LmeOptions	1.3.6.1.4.1.64.1.1.8	OCTET STRING	read-only	A set of option indicators, each of which, if present, indicates that a particular option within NM_LME is supported. Its interpretation is specified in the appropriate standard.
OCT hubManID	1.3.6.1.4.1.64.1.1.9	OCTET STRING	read-only	A 24 bit value that identifies the manufacturer.
OCT hubManProductID	1.3.6.1.4.1.64.1.1.10	OCTET STRING	read-only	A manufacturer-defined product identifier.
OCT hubManProductVersion	1.3.6.1.4.1.64.1.1.11	OCTET STRING	read-only	A manufacturer-defined product revision designation.
OCT hubManTelephoneNum	1.3.6.1.4.1.64.1.1.12	OCTET STRING	read-write	An ascii representation of the manufacturer's telephone number.
OCT hubName	1.3.6.1.4.1.64.1.1.13	OCTET STRING	read-write	This attribute is a text string up to 32 characters, of locally determined significance.
IP hubIPaddress	1.3.6.1.4.1.64.1.1.14	IpAddress	read-only	This attribute contains the IP address of the hub.
OCT hubEEpromRev	1.3.6.1.4.1.64.1.1.15	OCTET STRING	read-only	This attribute provides the eeprom revision number and is read from the hardware.
INT hubSecureMode	1.3.6.1.4.1.64.1.1.16	INTEGER	read-write	An integer value to set the hub in secure mode. In secure mode all ports are disabled by default, otherwise ports are enabled by default upon creation.
hmBasicCardTable	1.3.6.1.4.1.64.1.1.17		not-accessible	This table provide a management view of the HUB configuration specific to individual cards.
hmBasicCardEntry	1.3.6.1.4.1.64.1.1.17.1		not-accessible
INT gCardID	1.3.6.1.4.1.64.1.1.17.1.1	INTEGER	read-only	An 8 bit value unique within the hub.
INT gCardNumberOfPorts	1.3.6.1.4.1.64.1.1.17.1.2	INTEGER	read-only	This attribute contains the number of ports in the card object instance (MAC Entities).
OCT gCardName	1.3.6.1.4.1.64.1.1.17.1.3	OCTET STRING	read-write	This attribute is a text string up to 32 characters, of locally determined significance.
OCT gCardType	1.3.6.1.4.1.64.1.1.17.1.4	OCTET STRING	read-only	This attribute contains the type of card.
INT gCardRingNumberA	1.3.6.1.4.1.64.1.1.17.1.5	INTEGER	read-write	This attribute contains the Ring number associated with a UTP2112 type of card, or with RI/RO set of ports 'A' for a STP4104 type of card.
INT gCardRingNumberB	1.3.6.1.4.1.64.1.1.17.1.6	INTEGER	read-write	This attribute contains the Ring number associated with RI/RO set of ports 'B' for a STP4104 type of card.
INT gCardIbmModeA	1.3.6.1.4.1.64.1.1.17.1.7	INTEGER	read-write	This attribute specifies wether RI/RO set of ports 'A' for a STP4104 type of card is in IBM mode or normal mode.
INT gCardIbmModeB	1.3.6.1.4.1.64.1.1.17.1.8	INTEGER	read-write	This attribute specifies wether RI/RO set of ports 'B' for a STP4104 type of card is in IBM mode or normal mode.
INT gCardRingSpeedA	1.3.6.1.4.1.64.1.1.17.1.9	INTEGER	read-write	This attribute specifies wether RI/RO set of ports 'A' for a STP4104 runs at 4 or 16 Mbps. It is also used to display the speed of a UTP2112 type of cards.
INT gCardRingSpeedB	1.3.6.1.4.1.64.1.1.17.1.10	INTEGER	read-write	This attribute specifies wether RI/RO set of ports 'B' for a STP4104 runs at 4 or 16 Mbps.
hmBasicPortTable	1.3.6.1.4.1.64.1.1.18		not-accessible	This table provide a management view of the HUB configuration specific to individual ports.
hmBasicPortEntry	1.3.6.1.4.1.64.1.1.18.1		not-accessible
INT gCardBasicID	1.3.6.1.4.1.64.1.1.18.1.1	INTEGER	read-only	An 8 bit value unique within the hub.
INT gPortID	1.3.6.1.4.1.64.1.1.18.1.2	INTEGER	read-only	An 8 bit value unique in the group.
INT gPortType	1.3.6.1.4.1.64.1.1.18.1.3	INTEGER	read-only	Port connector type.
INT gPortAdminState	1.3.6.1.4.1.64.1.1.18.1.4	INTEGER	read-write	Indicates whether the port is enabled or disabled. A disabled port neither transmit nor receives.
INT gPortAutoPartitionState	1.3.6.1.4.1.64.1.1.18.1.5	INTEGER	read-only	Indicates whether the port is currently partitioned by the hub's auto-partition protection.
OCT gPortName	1.3.6.1.4.1.64.1.1.18.1.6	OCTET STRING	read-write	This attribute is a text string up to 32 characters, of locally determined significance.
INT gPortEffectiveState	1.3.6.1.4.1.64.1.1.18.1.7	INTEGER	read-only	Indicates redundant port's effective state.
INT gPortConfiguration	1.3.6.1.4.1.64.1.1.18.1.8	INTEGER	read-only	Indicates port's redundant configuration status.
INT gPortRedundantPort	1.3.6.1.4.1.64.1.1.18.1.9	INTEGER	read-write	Indicates redundant port's port number.
INT gPortRedundantCard	1.3.6.1.4.1.64.1.1.18.1.10	INTEGER	read-write	Indicates redundant port's card number.
INT gPortLinkStatus	1.3.6.1.4.1.64.1.1.18.1.11	INTEGER	read-only	Indicates port's link integrity status.
hmSelfTestCapability	1.3.6.1.4.1.64.1.2
OCT hubSelfTestID	1.3.6.1.4.1.64.1.2.1	OCTET STRING	read-only	A 48-bit unique identifier, the hub ethernet address is used.
TIK hubTimeSinceReset	1.3.6.1.4.1.64.1.2.2	TimeTicks	read-only	The time in tens of milliseconds since the last time that the system was reset. This counter has a value of 0 when initialized.
TIK hubResetTimeStamp	1.3.6.1.4.1.64.1.2.3	TimeTicks	read-only	Not a counter, this attribute provides the value of hubTimeSinceReset when the hub was last reset.
INT hubHealthState	1.3.6.1.4.1.64.1.2.4	INTEGER	read-only	This attribute will store the results of the startup diagnostics. The first octet indicates the overall results of the startup tests, while the remaining 8 octets will contain the results of the individual test. Each octet will contain a 1 if the test was passed, 2 if the test failed. The following list defines the meanings of each octet in the string: Octet 1 - overall test result Octet 2 - system NMI test Octet 3 - system timers test Octet 4 - system DMA test Octet 5 - 82586 test Octet 6 - backplane ethernet address test Octet 7 - NVRAM test Octet 8 - dual port RAM test Octet 9 - real time clock test
STR hubHealthText	1.3.6.1.4.1.64.1.2.5	DisplayString	read-only	This attribute provides a textual description of which test, if any, failed during diagnostics.
OCT hubHealthData	1.3.6.1.4.1.64.1.2.6	OCTET STRING	read-only	This attribute provides a textual description of which test, if any, failed during diagnostics.
INT hubSystemResetting	1.3.6.1.4.1.64.1.2.7	INTEGER	read-only	Indicates whether the hub is in the process of resetting completely (coldstart).
INT hubResetting	1.3.6.1.4.1.64.1.2.8	INTEGER	read-only	Indicates whether the hub is in the process of resetting or not (warmstart).
INT hubExecutingSelfTest	1.3.6.1.4.1.64.1.2.9	INTEGER	read-only	Indicates whether the hub is in the process of executing self diagnostics.
INT hubResetAction	1.3.6.1.4.1.64.1.2.10	INTEGER	read-write	Restart the hub if selecting reset.
hmPerfMonCapability	1.3.6.1.4.1.64.1.3
hmPerfMonRelayTable	1.3.6.1.4.1.64.1.3.1		not-accessible	This table provide a management view individual relay performance capability.
hmPerfMonRelayEntry	1.3.6.1.4.1.64.1.3.1.1		not-accessible
INT relayPerfID	1.3.6.1.4.1.64.1.3.1.1.1	INTEGER	read-only	This attribute is the value used in addressing the relay.
CTR relayTotalCollisions	1.3.6.1.4.1.64.1.3.1.1.2	Counter	read-only	The counter is incremented every time the hub enters a condition caused by simultaneous transmission and detection of external activity on one or more of its ports.
hmPerfMonPortTable	1.3.6.1.4.1.64.1.3.2		not-accessible	This table provide a management view of individual ports performance capability.
hmPerfMonPortEntry	1.3.6.1.4.1.64.1.3.2.1		not-accessible
INT gCardPerfID	1.3.6.1.4.1.64.1.3.2.1.1	INTEGER	read-only	This attribute represent the card number and is used to address the performance monitoring table.
INT gPortPerfID	1.3.6.1.4.1.64.1.3.2.1.2	INTEGER	read-only	This attribute represent the port number and is used to address the performance monitoring table.
CTR gPortReadableFrames	1.3.6.1.4.1.64.1.3.2.1.3	Counter	read-only	A representation of the total frames of legal length that have not been corrupted in transmission counted by the port object.
CTR gPortReadableOctets	1.3.6.1.4.1.64.1.3.2.1.4	Counter	read-only	It is sum of data and padding octets contained in ReadableFrames counted by the port object.
CTR gPortPygmys	1.3.6.1.4.1.64.1.3.2.1.5	Counter	read-only	The sum of pygmy frame fragments counted by the port object. They occur when a frame fragment was received which was not in collision and was not recognized as a valid ethernet packet. They normally make up less than 5% of Rx frames on hub-to-hub or hub-to-backbone connections and < 1% of total Rx frames for hub-DTE connections. Significantly higher levels may indicate external noise hits on the cabling, i.e. UTP in a noisy environment.
CTR gPortRunts	1.3.6.1.4.1.64.1.3.2.1.6	Counter	read-only	The sum of frames which were received then collided with another fram(e)s received by the hub. The port(s) which receive the collider frame(s) will increment their gPortCollisions and the port which was collided with will increment this counter. It is possible to count more runts than collisions for a specific port. As a rough guideline, less than 5% of the Rx frames should be runts.
CTR gPortFrameCheckSeqErrs	1.3.6.1.4.1.64.1.3.2.1.7	Counter	read-only	The sum of frames received on this port that are an integral number of octets in length and do not pass the FCS check. Normally less than 1% of Rx frames. Could be caused by line noise, loose connections, a faulty DTE, or a faulty hub.
CTR gPortAlignmentErrors	1.3.6.1.4.1.64.1.3.2.1.8	Counter	read-only	The sum of frames received on this port that are not an integral number of octets in length. Should be less than 1% of the total number of Rx frames and greater than or equal to gPortFramesTooLong and gPortFrameCheckSeqErrors. Could be caused by line noise, loose connections, a faulty DTE, or a faulty hub.
CTR gPortFramesTooLong	1.3.6.1.4.1.64.1.3.2.1.9	Counter	read-only	The sum of frames received on this port that are more than 1518 octets long. Should be < 1% of the total number of Rx frames. Could be caused by a faulty DTE or a faulty hub.
CTR gPortAutoPartitionCount	1.3.6.1.4.1.64.1.3.2.1.10	Counter	read-only	It is the number of times that this port has been automatically partitioned.
CTR gPortLateCollisions	1.3.6.1.4.1.64.1.3.2.1.11	Counter	read-only	This attribute is the total number of late collisions experienced by the port object. Usually indicates a DTE trying to Tx w/o checking the Ethernet for traffic first. May be due to a hardware fault on the sending DTE, or a segment which is too long for collision detection to work properly. Should normally be < 1% of total Rx frames.
CTR gPortCollisions	1.3.6.1.4.1.64.1.3.2.1.12	Counter	read-only	This attribute provides the total number of collisions encountered by the port object. The port that was collided with will count a runt. Normally less than 5% of the Rx frames should be collisions. Numbers significantly higher than this may indicate hardware problems or congestion.
CTR gPortAlarms	1.3.6.1.4.1.64.1.3.2.1.13	Counter	read-only	The number of times a threshold was exceeded on that port.
CTR gPortMulticastFrames	1.3.6.1.4.1.64.1.3.2.1.14	Counter	read-only	This attribute contains a count of frames successfully received by the port and are directed to an active non-broadcast group of addresses.
CTR gPortBroadcastFrames	1.3.6.1.4.1.64.1.3.2.1.15	Counter	read-only	This attribute contains the total number of broadcast frames received by the port object since system restart.
hmAddrTrackCapability	1.3.6.1.4.1.64.1.4
hmAddrTrackPortTable	1.3.6.1.4.1.64.1.4.1		not-accessible	This table provide a management view of individual port address tracking capability.
hmAddrTrackPortEntry	1.3.6.1.4.1.64.1.4.1.1		not-accessible
INT gCardAddrID	1.3.6.1.4.1.64.1.4.1.1.1	INTEGER	read-only	An 8 bit value unique within the hub.
INT gPortAddrID	1.3.6.1.4.1.64.1.4.1.1.2	INTEGER	read-only	An 8 bit value unique within the group.
OCT gPortLastSourceAddress	1.3.6.1.4.1.64.1.4.1.1.3	OCTET STRING	read-only	The source (ethernet) address of the last ReadableFrame received by this port.
CTR gPortSourceAddrChanges	1.3.6.1.4.1.64.1.4.1.1.4	Counter	read-only	This attribute counts the number of times the last source address has changed.
gandalf_bridge	1.3.6.1.4.1.64.2
bridgeConfigObject	1.3.6.1.4.1.64.2.1
OCT bridgeBaseAddress	1.3.6.1.4.1.64.2.1.1	OCTET STRING	read-only	The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique.
INT bridgeNumPorts	1.3.6.1.4.1.64.2.1.2	INTEGER	read-only	The number of (logical) ports controlled by this bridging entity.
INT bridgeType	1.3.6.1.4.1.64.2.1.3	INTEGER	read-only	Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
INT bridgeNumOfInterfaces	1.3.6.1.4.1.64.2.1.4	INTEGER	read-only	The number of interfaces controlled by this bridging entity, the interface stats are managed by MIB II interface group.
INT bridgePowerUpStatus	1.3.6.1.4.1.64.2.1.5	INTEGER	read-only	This attribute contains the result of any non fatal hardware diagnostics performed during the power on procedure.
IP bridgeIpAddr	1.3.6.1.4.1.64.2.1.6	IpAddress	read-only	This attribute contains the IP address of the bridge.
OCT bridgeManID	1.3.6.1.4.1.64.2.1.7	OCTET STRING	read-only	This is a 24 bit value that identifies the manufacturer.
OCT bridgeManProductVersion	1.3.6.1.4.1.64.2.1.8	OCTET STRING	read-only	This attribute provides the software revision number.
OCT bridgeEEpromRev	1.3.6.1.4.1.64.2.1.9	OCTET STRING	read-only	This attribute provides the eeprom revision number and is read from the hardware.
OCT bridgeSerialNum	1.3.6.1.4.1.64.2.1.10	OCTET STRING	read-only	This attribute provides the EBM Serial Number and is read from the hardware.
OCT bridgeHubChassis	1.3.6.1.4.1.64.2.1.11	OCTET STRING	read-only	This attribute provides information on the type of Hub Chassis this bridge is currently using.
bridgeTpObject	1.3.6.1.4.1.64.2.2
INT filterDatabaseSize	1.3.6.1.4.1.64.2.2.1	INTEGER	read-only	This attribute represents the number of entries into the filtering database.
INT numberOfDynamicEntries	1.3.6.1.4.1.64.2.2.2	INTEGER	read-only	This attribute contains a number of dynamic entries currently in the Filtering Database.
INT numberOfStaticEntries	1.3.6.1.4.1.64.2.2.3	INTEGER	read-only	This attribute contains a number of static entries currently in the Filtering Database.
INT agingState	1.3.6.1.4.1.64.2.2.4	INTEGER	read-only	When this attribute is ON, the Bridge will age dynamic station entries from the filter table automatically.
INT agingTime	1.3.6.1.4.1.64.2.2.5	INTEGER	read-only	The timeout period in seconds for aging out dynamically learned forwarding information.
INT learningState	1.3.6.1.4.1.64.2.2.6	INTEGER	read-only	When this attribute is ON, the Bridge will learn LAN station addresses automatically.
INT protocolFilterState	1.3.6.1.4.1.64.2.2.7	INTEGER	read-only	This attribute specifies whether protocol filtering is enabled or disabled.
INT broadcastForwardingState	1.3.6.1.4.1.64.2.2.8	INTEGER	read-only	This attribute specifies whether broadcast frames are being forwarded.
INT multicastForwardingState	1.3.6.1.4.1.64.2.2.9	INTEGER	read-only	This attribute specifies whether multicast frames are being forwarded.
bridgeTpFdbTable	1.3.6.1.4.1.64.2.2.10		not-accessible	A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
bridgeTpFdbEntry	1.3.6.1.4.1.64.2.2.10.1		not-accessible	Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
PHY bridgeDot1dTpFdbAddress	1.3.6.1.4.1.64.2.2.10.1.1	PhysAddress	read-only	A unicast MAC address for which the bridge has forwarding and/or filtering information.
INT bridgeDot1dTpFdbPort	1.3.6.1.4.1.64.2.2.10.1.2	INTEGER	read-only	Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1dTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the dot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of dot1dTpFdbStatus is not learned(3).
INT bridgeDot1dTpFdbStatus	1.3.6.1.4.1.64.2.2.10.1.3	INTEGER	read-only	The status of this entry. The meanings of the values are: other(1) : none of the following. This would include the case where some other MIB object (not the corresponding instance of dot1dTpFdbPort, nor an entry in the dot1dStaticTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dot1dTpFdbAddress are being forwarded. invalid(2) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. learned(3) : the value of the corresponding instance of dot1dTpFdbPort was learned, and is being used. self(4) : the value of the corresponding instance of dot1dTpFdbAddress represents one of the bridge's addresses. The corresponding instance of dot1dTpFdbPort indicates which of the bridge's ports has this address. mgmt(5) : the value of the corresponding instance of dot1dTpFdbAddress is also the value of an existing instance of dot1dStaticAddress.
bridgeLogicalPortTable	1.3.6.1.4.1.64.2.2.11		not-accessible	A table that contains information about every port that is associated with this transparent bridge.
bridgeLogicalPortEntry	1.3.6.1.4.1.64.2.2.11.1		not-accessible	A list of information for each port of a transparent bridge.
INT bridgeDot1dTpPort	1.3.6.1.4.1.64.2.2.11.1.1	INTEGER	read-only	The port number of the port for which this entry contains Transparent bridging management information.
INT bridgeDot1dTpPortMaxInfo	1.3.6.1.4.1.64.2.2.11.1.2	INTEGER	read-only	The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
CTR bridgeDot1dTpPortInFrames	1.3.6.1.4.1.64.2.2.11.1.3	Counter	read-only	The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function.
CTR bridgeDot1dTpPortOutFrames	1.3.6.1.4.1.64.2.2.11.1.4	Counter	read-only	The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function.
CTR bridgeDot1dTpPortInDiscards	1.3.6.1.4.1.64.2.2.11.1.5	Counter	read-only	Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process.
bridgeStpObject	1.3.6.1.4.1.64.2.3
INT bridgeDot1dStpProtocolSpecification	1.3.6.1.4.1.64.2.3.1	INTEGER	read-only	An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
INT bridgeDot1dStpPriority	1.3.6.1.4.1.64.2.3.2	INTEGER	read-only	The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
TIK bridgeDot1dStpTimeSinceTopologyChange	1.3.6.1.4.1.64.2.3.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
CTR bridgeDot1dStpTopChanges	1.3.6.1.4.1.64.2.3.4	Counter	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
OCT bridgeDot1dStpDesignatedRoot	1.3.6.1.4.1.64.2.3.5	OCTET STRING	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT bridgeDot1dStpRootCost	1.3.6.1.4.1.64.2.3.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT bridgeDot1dStpRootPort	1.3.6.1.4.1.64.2.3.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
INT bridgeDot1dStpMaxAge	1.3.6.1.4.1.64.2.3.8	INTEGER	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT bridgeDot1dStpHelloTime	1.3.6.1.4.1.64.2.3.9	INTEGER	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT bridgeDot1dStpHoldTime	1.3.6.1.4.1.64.2.3.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
INT bridgeDot1dStpForwardDelay	1.3.6.1.4.1.64.2.3.11	INTEGER	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state. For example, how long a port stays in the Listening state when moving from Blocking to Learning. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
INT bridgeDot1dStpBridgeMaxAge	1.3.6.1.4.1.64.2.3.12	INTEGER	read-only	The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1d/D9 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
INT bridgeDot1dStpBridgeHelloTime	1.3.6.1.4.1.64.2.3.13	INTEGER	read-only	The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
INT bridgeDot1dStpBridgeForwardDelay	1.3.6.1.4.1.64.2.3.14	INTEGER	read-only	The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1d/D9 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
bridgeStpPortTable	1.3.6.1.4.1.64.2.3.15		not-accessible	A table that contains port-specific information for the Spanning Tree Protocol.
bridgeStpPortEntry	1.3.6.1.4.1.64.2.3.15.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT bridgeDot1dStpPort	1.3.6.1.4.1.64.2.3.15.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT bridgeDot1dStpPortPriority	1.3.6.1.4.1.64.2.3.15.1.2	INTEGER	read-only	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
INT bridgeDot1dStpPortState	1.3.6.1.4.1.64.2.3.15.1.3	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
INT bridgeDot1dStpPortEnable	1.3.6.1.4.1.64.2.3.15.1.4	INTEGER	read-only	The enabled/disabled status of the port.
INT bridgeDot1dStpPortPathCost	1.3.6.1.4.1.64.2.3.15.1.5	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
OCT bridgeDot1dStpPortDesignatedRoot	1.3.6.1.4.1.64.2.3.15.1.6	OCTET STRING	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT bridgeDot1dStpPortDesignatedCost	1.3.6.1.4.1.64.2.3.15.1.7	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT bridgeDot1dStpPortDesignatedBridge	1.3.6.1.4.1.64.2.3.15.1.8	OCTET STRING	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OCT bridgeDot1dStpPortDesignatedPort	1.3.6.1.4.1.64.2.3.15.1.9	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
CTR bridgeDot1dStpPortForwardTransitions	1.3.6.1.4.1.64.2.3.15.1.10	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
bridgeStaticObject	1.3.6.1.4.1.64.2.4
bridgeStaticTable	1.3.6.1.4.1.64.2.4.1		not-accessible	A table containing filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.
bridgeStaticEntry	1.3.6.1.4.1.64.2.4.1.1		not-accessible	Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.
PHY bridgeDot1dStaticAddress	1.3.6.1.4.1.64.2.4.1.1.1	PhysAddress	read-only	The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.
INT bridgeDot1dStaticReceivePort	1.3.6.1.4.1.64.2.4.1.1.2	INTEGER	read-only	Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OCT bridgeDot1dStaticAllowedToGoTo	1.3.6.1.4.1.64.2.4.1.1.3	OCTET STRING	read-only	This attribute contains a representation of the Outbound Ports associated with this static entry.
INT bridgeDot1dStaticStatus	1.3.6.1.4.1.64.2.4.1.1.4	INTEGER	read-only	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
bridgeProtFiltTable	1.3.6.1.4.1.64.2.4.2		not-accessible	A table containing protocol filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames containing protocol ID are allowed to be forwarded.
bridgeProtFiltEntry	1.3.6.1.4.1.64.2.4.2.1		not-accessible	Protocol filtering information configured into the bridge by (local or network) management.
INT brProtFiltIndex	1.3.6.1.4.1.64.2.4.2.1.1	INTEGER	read-only	This attribute is used as a unique identifier into the Bridge Protocol Filtering Table.
OCT brProtFiltName	1.3.6.1.4.1.64.2.4.2.1.2	OCTET STRING	read-only	A text string of up to 32 characters, of locally determined significance used to identify this Protocol filter.
OCT brProtFiltId	1.3.6.1.4.1.64.2.4.2.1.3	OCTET STRING	read-only	This attribute identifies the protocol type to be filtered.
OCT brProtFiltPortMap	1.3.6.1.4.1.64.2.4.2.1.4	OCTET STRING	read-only	This attribute contains a representation of the Outbound Ports associated with this static entry.
bridgeProtPriorityTable	1.3.6.1.4.1.64.2.4.3		not-accessible	A table containing protocol priority information configured into the bridge by (local or network) management specifying the priority in which frames will be transmitted on the wide area network links.
bridgeProtPriorityEntry	1.3.6.1.4.1.64.2.4.3.1		not-accessible	Protocol priority information configured into the bridge by (local or network) management.
INT brProtPriorityIndex	1.3.6.1.4.1.64.2.4.3.1.1	INTEGER	read-only	This attribute is used as a unique identifier into the Bridge Protocol Priority Table.
OCT brProtPriorityName	1.3.6.1.4.1.64.2.4.3.1.2	OCTET STRING	read-only	A text string of up to 32 characters, of locally determined significance used to identify this Protocol Priority entry.
OCT brProtPriorityId	1.3.6.1.4.1.64.2.4.3.1.3	OCTET STRING	read-only	This attribute identifies the protocol type to be prioritized.
INT brProtPriorityLevel	1.3.6.1.4.1.64.2.4.3.1.4	INTEGER	read-only	The priority assigned to the associated Portocol ID
wanPhysicalObject	1.3.6.1.4.1.64.2.5
wanPhysTable	1.3.6.1.4.1.64.2.5.1		not-accessible	This table represent a view of Management Facilities for WAN physical ports.
wanPhysEntry	1.3.6.1.4.1.64.2.5.1.1		not-accessible	This list contains counters and parameters related to the management of WAN ports.
INT wanPhysPortId	1.3.6.1.4.1.64.2.5.1.1.1	INTEGER	read-only	This attribute is used as a unique identifier for the Bridge WAN interface.
OCT wanPhysPortName	1.3.6.1.4.1.64.2.5.1.1.2	OCTET STRING	read-only	A text string of up to 32 characters, of locally determined significance used to identify this WAN interface.
INT wanPhysLogicalPort	1.3.6.1.4.1.64.2.5.1.1.3	INTEGER	read-only	This attribute shows the logical port for this Wan interface. Redundant links will have the same logical port.
INT wanPhysDcdLevel	1.3.6.1.4.1.64.2.5.1.1.4	INTEGER	read-only	This attribute shows the level of the DCD EIA signal on this particular WAN link.
INT wanPhysLinkLevel	1.3.6.1.4.1.64.2.5.1.1.5	INTEGER	read-only	This attribute shows whether the WAN link is 'up' or 'down'.
GAU wanTxLinkUtilization	1.3.6.1.4.1.64.2.5.1.1.6	Gauge	read-only	This attribute shows the link utilization in the TX direction. The utilization is a percentage of the bandwidth (0 to 100).
GAU wanRxLinkUtilization	1.3.6.1.4.1.64.2.5.1.1.7	Gauge	read-only	This attribute shows the link utilization in the RX direction. The utilization is a percentage of the bandwidth (0 to 100).
INT wanPhysFrameErrors	1.3.6.1.4.1.64.2.5.1.1.8	INTEGER	read-only	This attribute shows the number of frame errors on this WAN interface.
INT wanCompressionState	1.3.6.1.4.1.64.2.5.1.1.9	INTEGER	read-only	This attribute shows whether data compression is enabled or disabled.
INT wanCompressionRatio	1.3.6.1.4.1.64.2.5.1.1.10	INTEGER	read-only	An indication of how well the Bridge is compressing data that is to be transmitted to another bridge. A value of 100 shows no compression, a value of 300 shows a 3 : 1 compression.
ieee8023Object	1.3.6.1.4.1.64.2.6
ieeeIfTable	1.3.6.1.4.1.64.2.6.1		not-accessible	This table represent a view of Management Facilities for the IEEE802.3 CSMA/CD MAC layer. The object was defined by IEEE in a 802.3 standard.
ieeeIfEntry	1.3.6.1.4.1.64.2.6.1.1		not-accessible	This list contains counters and parameters related to the management of the IEEE802.3 MAC layer.
INT ieeeIfIndex	1.3.6.1.4.1.64.2.6.1.1.1	INTEGER	read-only	This attribute is used as a unique identifier for the Bridge LAN interface.
CTR ieeeFrmsTxOk	1.3.6.1.4.1.64.2.6.1.1.2	Counter	read-only	This attribute contains a count of frames that are successfully transmitted.
CTR ieeeSingleCollFrms	1.3.6.1.4.1.64.2.6.1.1.3	Counter	read-only	This attribute contains a count of frames that are involved in a single collision and are subsequently transmitted successfuly.
CTR ieeeMultipleCollFrms	1.3.6.1.4.1.64.2.6.1.1.4	Counter	read-only	This attribute contains a count of frames that are involved in more than one collision and are subsequently transmitted successfully.
CTR ieeeOctetsTxOk	1.3.6.1.4.1.64.2.6.1.1.5	Counter	read-only	This attribute contains a count of data and padding octets in frames that are successfully transmitted.
CTR ieeeDefTx	1.3.6.1.4.1.64.2.6.1.1.6	Counter	read-only	This attribute contains a count of frames whose transmission was delayed on its first attempt becasue the medium was busy.
CTR ieeeMcastFrmsTxOk	1.3.6.1.4.1.64.2.6.1.1.7	Counter	read-only	This attribute contains a count of frames that are successfully transmitted as indicated by the status value transmitOK, to a group destination address other than broadcast.
CTR ieeeBcastFrmsTxOk	1.3.6.1.4.1.64.2.6.1.1.8	Counter	read-only	This attribute contains a number of broadcast frames transmitted to the LAN connection.
CTR ieeeLateColls	1.3.6.1.4.1.64.2.6.1.1.9	Counter	read-only	This attribute contains a count of the times that a collision has been detected later than 512 bit times into the transmitted packet.
CTR ieeeExcessColls	1.3.6.1.4.1.64.2.6.1.1.10	Counter	read-only	This attribute contains a count of frames that due to excessive collisions are not transmitted successfully.
CTR ieeeIntlMacTxError	1.3.6.1.4.1.64.2.6.1.1.11	Counter	read-only	This attribute contains a count of frames which would otherwise be transmitted by the station,but could not be sent due to an internal MAC sublayer transmit error.
CTR ieeeCsErrors	1.3.6.1.4.1.64.2.6.1.1.12	Counter	read-only	This attribute contains number of frames that were lost because the ethernet carrier signal was lost.
CTR ieeeExcessDef	1.3.6.1.4.1.64.2.6.1.1.13	Counter	read-only	This attribute contains a count of frames which deferred for an excessive period of time.
CTR ieeeFrmsRxOk	1.3.6.1.4.1.64.2.6.1.1.14	Counter	read-only	This attribute contains a count of frames that are successfully received.
CTR ieeeOctetsRxOk	1.3.6.1.4.1.64.2.6.1.1.15	Counter	read-only	This attribute contains a count of data and padding octets in frames that are successfully received.
CTR ieeeMcastFrmsRxOk	1.3.6.1.4.1.64.2.6.1.1.16	Counter	read-only	This attribute contains a count of frames that are successfully received and are directed to an active non-broadcast group of addresses.
CTR ieeeBcastFrmsRxOk	1.3.6.1.4.1.64.2.6.1.1.17	Counter	read-only	This attribute contains a number of broadcast frames received from the LAN connection.
CTR ieeeTooLongErrors	1.3.6.1.4.1.64.2.6.1.1.18	Counter	read-only	This attribute contains a count of frames that are received and exceeded the maximum permitted frame size. This counter is incremented when the status of a frame reception is frame TooLong.
CTR ieeeAlignErrors	1.3.6.1.4.1.64.2.6.1.1.19	Counter	read-only	This attribute contains a count of frames that are not an integral of octets in length and do not pass the Frame Check Sequence(FCS) check.This counter is incremented when the ReceiveStatus is reported as alignmentError.
CTR ieeeFcsErrors	1.3.6.1.4.1.64.2.6.1.1.20	Counter	read-only	This attribute contains a count of frames that are an integral of octets in length and do not pass the Frame Check Sequence(FCS) check. This counter is incremented when the ReceiveStatus is reported as frameCheckError.
CTR ieeeIrLengthErrors	1.3.6.1.4.1.64.2.6.1.1.21	Counter	read-only	This attribute contains a count of frames with a length field value, between the minimum unpadded LLC data size and the maximum allowed LLC data size inclusive, that does not match the number of LLC data octets received. The counter also contains frames with a length field value less than the minimum unpadded LLC data size.
CTR ieeeOorLengthFields	1.3.6.1.4.1.64.2.6.1.1.22	Counter	read-only	This attribute contains a count of frames with a length field value greater than the maximum allowed LLC data size.
CTR ieeeIntlMacRcvErrors	1.3.6.1.4.1.64.2.6.1.1.23	Counter	read-only	This attribute contains a count of frames which would otherwise be received by the station,but could not be accepted due to an internal MAC sublayer receive error.
INT ieeeInitMac	1.3.6.1.4.1.64.2.6.1.1.24	INTEGER	read-only	This attributes indicates wether the underlying IEEE 802.3 MAC was initialized.
INT ieeePromRxStatus	1.3.6.1.4.1.64.2.6.1.1.25	INTEGER	read-only	This attribute contains the current state of the Prom.
INT ieeeMacSubLayerStatus	1.3.6.1.4.1.64.2.6.1.1.26	INTEGER	read-only	This attribute contains the current state of the Receive side of the underlying IEEE 802.3 resource.
INT ieeeTxStatus	1.3.6.1.4.1.64.2.6.1.1.27	INTEGER	read-only	This attribute contains the current state of the Transmit side of the underlying IEEE 802.3 resource.
INT ieeeMcastRxStatus	1.3.6.1.4.1.64.2.6.1.1.28	INTEGER	read-only	This attribute specifies if Multicast frames will be received by the underlying IEEE 802.3 resource.
OCT ieeeMacAddress	1.3.6.1.4.1.64.2.6.1.1.29	OCTET STRING	read-only	This attribute contains the specific MAC Address of the individual MAC Entity associated with the Port.
CTR ieeeSqeTestErrors	1.3.6.1.4.1.64.2.6.1.1.30	Counter	read-only	This attribute contains a count of errors detected when performing an SQE test. This counter is not currently supported.
gandalf_generic	1.3.6.1.4.1.64.3
gandalfLog	1.3.6.1.4.1.64.3.1
ganEventLogTable	1.3.6.1.4.1.64.3.1.1		not-accessible	A table containing alarm information.
ganEventLogEntry	1.3.6.1.4.1.64.3.1.1.1		not-accessible	Log information of alarms generated by the product, including time of event, severity and description.
INT ganEventLogIndex	1.3.6.1.4.1.64.3.1.1.1.1	INTEGER	read-only	An index to the alarm table, not relevant other than to display the table.
OCT ganEventLogDate	1.3.6.1.4.1.64.3.1.1.1.2	OCTET STRING	read-only	This date on which the event causing the alarm to be generated occurred.
OCT ganEventLogTime	1.3.6.1.4.1.64.3.1.1.1.3	OCTET STRING	read-only	This time at which the event causing the alarm to be generated occurred.
INT ganEventLogEventNum	1.3.6.1.4.1.64.3.1.1.1.4	INTEGER	read-only	An index to the alarm table, not relevant other than to display the table. This attribute has been deprecated because it duplicates the ganEventLogIndex.
INT ganEventLogSeverity	1.3.6.1.4.1.64.3.1.1.1.5	INTEGER	read-only	An index to the event log table, not relevant other than to display the table.
OCT ganEventLogDescription	1.3.6.1.4.1.64.3.1.1.1.6	OCTET STRING	read-only	Textual description of the event log.
snmpAdminCapability	1.3.6.1.4.1.64.3.2
snmpCommunityTable	1.3.6.1.4.1.64.3.2.1		not-accessible	This table provide a management view of which device can poll this resource via SNMP based on the Community Name, IP address and Privilege. Sets are supported ONLY in the Gandalf WAN proxy agent. To set a new community entry, use the instance 25 as the index value. Example: snmpCommunityName.25 Set all objects in the entry using instance 25. When the last object is set, the agent checks for duplicate entries and returns an error status if any found, otherwise the new entry is inserted at the next available position in the table. Existing entries may be modified by setting the a new value using an existing instance. The agent rejects any attempt to duplicate an entry. Objects may be deleted by setting the community name to one or more spaces. The entry is deleted and any vacated row is filled in by moving the last valid row there. NOTE: The object snmpTrapRemotePort is not supported in the Gandalf WAN Proxy agent.
snmpCommunityEntry	1.3.6.1.4.1.64.3.2.1.1		not-accessible	This is a list of attributes that make the Community Table.
INT snmpCommunityIndex	1.3.6.1.4.1.64.3.2.1.1.1	INTEGER	read-only	An 8 bit value unique within the Community Name.
OCT snmpCommunityName	1.3.6.1.4.1.64.3.2.1.1.2	OCTET STRING	read-only	The name of a Community supported by this SNMP agent.
IP snmpCommunityIpAddr	1.3.6.1.4.1.64.3.2.1.1.3	IpAddress	read-only	The Ip Address of a manager associated with a Community that will be supported by the SNMP agent. A value of zero means that all managers from that Community will be supported.
INT snmpCommunityPriv	1.3.6.1.4.1.64.3.2.1.1.4	INTEGER	read-only	The access priviledge associated with a Community.
snmpTrapCommunityTable	1.3.6.1.4.1.64.3.2.2		not-accessible	This table provide a management view of which device(s) (i.e. LAN Managers) this resource will send Trap to. Sets are supported ONLY in the Gandalf WAN proxy agent. To set a new community entry, use the instance 25 as the index value. Example: snmpTrapCommunityName.25 Set all objects in the entry using instance 25. When the last object is set, the agent checks for duplicate entries and returns an error status if any found, otherwise the new entry is inserted at the next available position in the table. Existing entries may be modified by setting the a new value using an existing instance. The agent rejects any attempt to duplicate an entry. Objects may be deleted by setting the community name to one or more spaces. The entry is deleted and any vacated row is filled in by moving the last valid row there.
snmpTrapCommunityEntry	1.3.6.1.4.1.64.3.2.2.1		not-accessible	This is a list of attributes that make the Trap Community Table.
INT snmpTrapCommunityIndex	1.3.6.1.4.1.64.3.2.2.1.1	INTEGER	read-only	An 8 bit value unique within the Community Name.
OCT snmpTrapCommunityName	1.3.6.1.4.1.64.3.2.2.1.2	OCTET STRING	read-only	The name of a Trap Community associated with a LAN Manager.
IP snmpTrapIpAddr	1.3.6.1.4.1.64.3.2.2.1.3	IpAddress	read-only	The Ip Address of a manager that will receive Traps generated by this SNMP agent.
INT snmpTrapRemotePort	1.3.6.1.4.1.64.3.2.2.1.4	INTEGER	read-only	The remote UDP port number used by an agent to receive Traps (usually port 162 is used).
OCT snmpTrapDescription	1.3.6.1.4.1.64.3.2.3	OCTET STRING	read-only	This attribute provide a description of Enterprise Specific Traps. This is also known as the 'interesting information' of an Enterprise Specific Trap.
gandalf_2590	1.3.6.1.4.1.64.4
gandalf_wanNode	1.3.6.1.4.1.64.5
gandalf_products	1.3.6.1.4.1.64.6
gProd_wan	1.3.6.1.4.1.64.6.1
gProxy	1.3.6.1.4.1.64.6.1.1
g2300	1.3.6.1.4.1.64.6.1.2
g2050	1.3.6.1.4.1.64.6.1.3
gProd_hub	1.3.6.1.4.1.64.6.2
ecm1000	1.3.6.1.4.1.64.6.2.1
rsc9000	1.3.6.1.4.1.64.6.2.3
gProd_bridge	1.3.6.1.4.1.64.6.3
lanline5220L	1.3.6.1.4.1.64.6.3.2
xbr6202	1.3.6.1.4.1.64.6.3.3
lanline5220e	1.3.6.1.4.1.64.6.3.4
lanline5225i	1.3.6.1.4.1.64.6.3.5
lanline5240i	1.3.6.1.4.1.64.6.3.6
xbr6204	1.3.6.1.4.1.64.6.3.7
lanline5221	1.3.6.1.4.1.64.6.3.8
lanline5242	1.3.6.1.4.1.64.6.3.9
gProd_gateway	1.3.6.1.4.1.64.6.4
wgm2590_hub	1.3.6.1.4.1.64.6.4.1
wgm2590_standalone	1.3.6.1.4.1.64.6.4.2
gProd_termserver	1.3.6.1.4.1.64.6.5
gts1000	1.3.6.1.4.1.64.6.5.1
gtsplus	1.3.6.1.4.1.64.6.5.2
gProd_router	1.3.6.1.4.1.64.6.6
lanline5250i	1.3.6.1.4.1.64.6.6.5
lanline5250L	1.3.6.1.4.1.64.6.6.7
lanline5242er	1.3.6.1.4.1.64.6.6.8
lanline5250fr	1.3.6.1.4.1.64.6.6.9
xpressway5250isdn_typ1	1.3.6.1.4.1.64.6.6.10
xpressway5250isdn_typ2	1.3.6.1.4.1.64.6.6.11
gandalf_nms	1.3.6.1.4.1.64.7
gandalf_wanProxy	1.3.6.1.4.1.64.8
gandalf_rlanisdn	1.3.6.1.4.1.64.9
gandalf_termserver	1.3.6.1.4.1.64.10
gandalf_router	1.3.6.1.4.1.64.11
gandalf_experimental	1.3.6.1.4.1.64.12

RFC description

Gandalf enterprise MIB for Xpressway, LanLine, and WAN proxy products including hub and bridge management.

Start monitoring Legacy Gandalf Technologies hub equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GANDALF-ENTERPRISE-MIB

What Is GANDALF-ENTERPRISE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description