FRSLD-MIB

All MIBs › FRSLD-MIB

Organization: IETF Frame Relay Service MIB Working Group

Last Updated: 2002-01-03

Category: Frame Relay

Description: Defines managed objects for Frame Relay Service Level Definitions as specified in FRF.13, including metrics such as data delivery ratio and service availability.

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring FRSLD-MIB with a free 30-day trial of IPNetwork Monitor.

What Is FRSLD-MIB?

FRSLD-MIB is a vendor-neutral IETF-derived MIB implementing the Frame Relay Forum's FRF.13 Service Level Definitions, which standardize metrics for measuring the quality of service delivered over a Frame Relay network. It exposes objects for service-level performance metrics such as data delivery ratio, frame delay, and service availability, allowing comparison of actual network performance against contracted service levels. Its monitoring focus is performance/service-quality status rather than hardware health, letting an operator track whether a Frame Relay service meets committed availability and delivery-ratio targets over a measurement interval. It explicitly depends on the FRF.13 specification from the Frame Relay Forum and is a standards-based module rather than a proprietary vendor extension. It is deployed by carriers and enterprises as an FRSLD-MIB reference for measuring Frame Relay circuit SLAs across a WAN.

IPNetwork Monitor allows you to monitor SNMP objects defined in FRSLD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB (FRF.13), not tied to a specific manufacturer; applies to Frame Relay network equipment and carrier circuits

Monitoring Examples

No sample objects were captured for this entry, so no specific table names can be cited; based on the module description, a realistic scenario is an operator periodically reading service-level metric objects such as data delivery ratio and availability percentage for a given Frame Relay PVC to verify the carrier is meeting a contracted SLA, flagging a breach if delivery ratio drops below the agreed threshold.

What Can Be Monitored

data delivery ratio
frame delay
service availability percentage
SLA compliance metrics

Imported Objects

From FRAME-RELAY-DTE-MIB

DLCI

From HCNUM-TC

CounterBasedGauge64

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
mib-2

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TimeStamp

How to Use in IPNetwork Monitor

Example using frsldPvcDataMissedPolls OID:

Select a device implementing FRSLD-MIB as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type frsldPvcDataMissedPolls into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of polls that have been determined to be missed. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
frsldCapabilities	1.3.6.1.2.1.95.2
frsldCapabilitiesGroup	1.3.6.1.2.1.95.3.1.15			A collection of required objects providing capability information and control for this MIB module.
frsldCompliance	1.3.6.1.2.1.95.3.2.1			The compliance statement for SNMP entities which support with Frame Relay Service Level Definitions. This group defines the minimum level of support required for compliance.
frsldConformance	1.3.6.1.2.1.95.3
I32 frsldMaxPvcCtrls	1.3.6.1.2.1.95.2.4	Integer32	read-write	The maximum number of control rows that can be created in frsldPvcCtrlTable. Sets to this object lower than the current value of frsldNumPvcCtrls should result in inconsistentValue.
I32 frsldMaxSmplCtrls	1.3.6.1.2.1.95.2.6	Integer32	read-write	The maximum number of control rows that can be created in frsldSmplCtrlTable. Sets to this object lower than the current value of frsldNumSmplCtrls should result in inconsistentValue.
frsldMIB	1.3.6.1.2.1.95			The MIB module to describe generic objects for FRF.13 Frame Relay Service Level Definitions.
frsldMIBCompliances	1.3.6.1.2.1.95.3.2
frsldMIBGroups	1.3.6.1.2.1.95.3.1
G32 frsldNumPvcCtrls	1.3.6.1.2.1.95.2.5	Gauge32	read-only	The current number of rows in frsldPvcCtrlTable.
G32 frsldNumSmplCtrls	1.3.6.1.2.1.95.2.7	Gauge32	read-only	The current number of rows in frsldSmplCtrlTable.
frsldObjects	1.3.6.1.2.1.95.1
I32 frsldPvcCtrlDelayFrSize	1.3.6.1.2.1.95.1.1.1.6	Integer32	read-create	The size of the payload in the frame used for calculation of network delay.
I32 frsldPvcCtrlDelayTimeOut	1.3.6.1.2.1.95.1.1.1.8	Integer32	read-create	A delay frame will count as a missed poll if it is not updated in the time specified by frsldPvcCtrlDelayTimeOut.
INT frsldPvcCtrlDelayType	1.3.6.1.2.1.95.1.1.1.7	INTEGER	read-create	The type of delay measurement performed.
INT frsldPvcCtrlDeleteOnPurge	1.3.6.1.2.1.95.1.1.1.10	INTEGER	read-create	This object defines whether rows will automatically be deleted from the tables when the information is purged. - A value of none(1) indicates that no rows will deleted. The last known values will be preserved. - A value of sampleControls(2) indicates that all associated sample control rows will be deleted. - A value of all(3) indicates that all associated rows SHOULD be deleted.
DLC frsldPvcCtrlDlci	1.3.6.1.2.1.95.1.1.1.1	DLCI	not-accessible	The value of this object is equal to the DLCI value for this PVC.
frsldPvcCtrlEntry	1.3.6.1.2.1.95.1.1.1		not-accessible	An entry in the Frame Relay Service Level Definitions PVC control table.
TIM frsldPvcCtrlLastPurgeTime	1.3.6.1.2.1.95.1.1.1.11	TimeStamp	read-only	This object returns the value of sysUpTime at the time the information was last purged. This value SHOULD be set to the sysUpTime upon setting frsldPvcCtrlStatus to active(1) for the first time. Each time a discontinuity in the counters occurs, this value MUST be set to the sysUpTime. If frsldPvcCtrlStatus has never been active(1), this object SHOULD return 0. This object SHOULD be used as the discontinuity timer for the counters in frsldPvcDataTable.
I32 frsldPvcCtrlPacketFreq	1.3.6.1.2.1.95.1.1.1.5	Integer32	read-create	The frequency in seconds between initiation of specialized packets used to collect delay and / or delivery information as supported by the device. A value of zero indicates that no packets will be sent.
I32 frsldPvcCtrlPurge	1.3.6.1.2.1.95.1.1.1.9	Integer32	read-create	This object defines the amount of time the device will wait, after discovering that a DLCI does not exist, the DLCI was deleted or the value of frsldPvcCtrlStatus changes from active(1) to either notInService(2) or notReady(3), prior to automatically purging the history in the sample tables and resetting the data in the data tables to all zeroes. If frsldPvcCtrlStatus is manually set to destroy(6), this object does not apply.
FRS frsldPvcCtrlReceiveRP	1.3.6.1.2.1.95.1.1.1.3	FrsldRxRP	not-accessible	The reference point this PVC uses for calculation of receiver related statistics. This object together with frsldPvcCtrlTransmitRP define the measurement domain.
ROW frsldPvcCtrlStatus	1.3.6.1.2.1.95.1.1.1.4	RowStatus	read-create	The status of the current row. This object is used to add, delete, and disable rows in this table. When the status changes to active(1) for the first time, a row will also be added to the data table below. This row SHOULD not be removed until the status is changed to deleted. When this object is set to destroy(6), all associated sample and data table rows will also be deleted. When this object is changed from active(1) to any other valid value, the defined purge behavior will affect the data and sample tables. The rows added to this table MUST have a valid ifIndex and an ifType related to frame relay. Further, the reference points referred to by frsldPvcCtrlTransmitRP and frsldPvcCtrlReceiveRP MUST be supported (see the frsldRPCaps object). If at any point the row is not in the active(1) state and the DLCI no longer exists, the state SHOULD report notReady(3). The data in this table SHOULD persist through power cycles. The symantics of readiness for the rows still applies. This means that it is possible for a row to be reprovisioned as notReady(3) if the underlying DLCI does not persist.
frsldPvcCtrlTable	1.3.6.1.2.1.95.1.1		not-accessible	The Frame Relay Service Level Definitions PVC control table.
FRS frsldPvcCtrlTransmitRP	1.3.6.1.2.1.95.1.1.1.2	FrsldTxRP	not-accessible	The reference point this PVC uses for calculation of transmitter related statistics. This object together with frsldPvcCtrlReceiveRP define the measurement domain.
BIT frsldPvcCtrlWriteCaps	1.3.6.1.2.1.95.2.1	Bits	read-only	This object specifies the write capabilities for the read-create objects of the PVC Control table. If the corresponding bit is enabled (1), the agent supports writes to that object.
C32 frsldPvcDataDataDeliveredC	1.3.6.1.2.1.95.1.3.1.6	Counter32	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataDataDeliveredE	1.3.6.1.2.1.95.1.3.1.7	Counter32	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataDataOfferedC	1.3.6.1.2.1.95.1.3.1.8	Counter32	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP within CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataDataOfferedE	1.3.6.1.2.1.95.1.3.1.9	Counter32	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP in excess of the CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
frsldPvcDataEntry	1.3.6.1.2.1.95.1.3.1		not-accessible	An entry in the Frame Relay Service Level Definitions data table.
C32 frsldPvcDataFrDeliveredC	1.3.6.1.2.1.95.1.3.1.2	Counter32	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataFrDeliveredE	1.3.6.1.2.1.95.1.3.1.3	Counter32	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataFrOfferedC	1.3.6.1.2.1.95.1.3.1.4	Counter32	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP within CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataFrOfferedE	1.3.6.1.2.1.95.1.3.1.5	Counter32	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP in excess of the CIR. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCDataDeliveredC	1.3.6.1.2.1.95.1.3.1.14	Counter64	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR. This object is a 64-bit version of frsldPvcDataDataDeliveredC. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCDataDeliveredE	1.3.6.1.2.1.95.1.3.1.15	Counter64	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR. This object is a 64-bit version of frsldPvcDataDataDeliveredE. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCDataOfferedC	1.3.6.1.2.1.95.1.3.1.16	Counter64	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP within CIR. This object is a 64-bit version of frsldPvcDataDataOfferedC. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCDataOfferedE	1.3.6.1.2.1.95.1.3.1.17	Counter64	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP in excess of the CIR. This object is a 64-bit version of frsldPvcDataDataOfferedE. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCFrDeliveredC	1.3.6.1.2.1.95.1.3.1.10	Counter64	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR. This object is a 64-bit version of frsldPvcDataFrDeliveredC. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCFrDeliveredE	1.3.6.1.2.1.95.1.3.1.11	Counter64	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR. This object is a 64-bit version of frsldPvcDataFrDeliveredE. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCFrOfferedC	1.3.6.1.2.1.95.1.3.1.12	Counter64	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP within CIR. This object is a 64-bit version of frsldPvcDataFrOfferedC. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C64 frsldPvcDataHCFrOfferedE	1.3.6.1.2.1.95.1.3.1.13	Counter64	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP in excess of the CIR. This object is a 64-bit version of frsldPvcDataFrOfferedE. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
C32 frsldPvcDataMissedPollsEx	1.3.6.1.2.1.95.1.3.1.1	Counter32	read-only	The total number of polls that have been determined to be missed. These polls are typically associated with the calculation of delay but may also be used for the calculation of other statistics. If an anticipated poll is not received in a reasonable amount of time, it should be counted as missed. The value used to determine the reasonable amount of time is contained in frsldPvcCtrlDelayTimeOut. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
frsldPvcDataTable	1.3.6.1.2.1.95.1.3		not-accessible	The Frame Relay Service Level Definitions data table. This table contains accumulated values of the collected data. It is the table that should be referenced by external polling mechanisms if time based polling be desired.
C32 frsldPvcDataUnavailables	1.3.6.1.2.1.95.1.3.1.19	Counter32	read-only	The number of times this PVC was declared unavailable for any reason since this row was created. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by frsldPvcCtrlLastPurgeTime.
TIK frsldPvcDataUnavailableTime	1.3.6.1.2.1.95.1.3.1.18	TimeTicks	read-only	The amount of time this PVC was declared unavailable for any reason since this row was created.
frsldPvcDelayCtrlGroup	1.3.6.1.2.1.95.3.1.3			A collection of optional objects providing delay control information applicable to a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcPacketGroup and frsldPvcDelayDataGroup MUST also be implemented.
frsldPvcDelayDataGroup	1.3.6.1.2.1.95.3.1.6			A collection of optional objects providing delay data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcDelayCtrlGroup MUST also be implemented.
frsldPvcHCFrameDataGroup	1.3.6.1.2.1.95.3.1.7			A collection of optional objects providing high capacity frame data collected on a PVC which implements Service Level Definitions.
frsldPvcHCOctetDataGroup	1.3.6.1.2.1.95.3.1.8			A collection of optional objects providing high capacity octet data collected on a PVC which implements Service Level Definitions.
frsldPvcPacketGroup	1.3.6.1.2.1.95.3.1.2			A collection of optional objects providing packet level control information applicable to a PVC which implements Service Level Definitions.
frsldPvcReqCtrlGroup	1.3.6.1.2.1.95.3.1.1			A collection of required objects providing control information applicable to a PVC which implements Service Level Definitions.
frsldPvcReqDataGroup	1.3.6.1.2.1.95.3.1.5			A collection of required objects providing data collected on a PVC which implements Service Level Definitions.
frsldPvcSampleAvailGroup	1.3.6.1.2.1.95.3.1.13			A collection of optional objects providing availability sample data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcReqDataGroup MUST also be implemented.
frsldPvcSampleCtrlGroup	1.3.6.1.2.1.95.3.1.4			A collection of optional objects providing sample control information applicable to a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcReqDataGroup and frsldPvcSampleGeneralGroup MUST also be implemented.
frsldPvcSampleDataGroup	1.3.6.1.2.1.95.3.1.10			A collection of optional objects providing data and frame delivery sample data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcReqDataGroup MUST also be implemented.
frsldPvcSampleDelayGroup	1.3.6.1.2.1.95.3.1.9			A collection of optional objects providing delay sample data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcDelayCtrlGroup MUST also be implemented.
frsldPvcSampleEntry	1.3.6.1.2.1.95.1.4.1		not-accessible	An entry in the Frame Relay Service Level Definitions data sample table.
frsldPvcSampleGeneralGroup	1.3.6.1.2.1.95.3.1.14			A collection of optional objects providing general sample data collected on a PVC which implements Service Level Definitions.
frsldPvcSampleHCDataGroup	1.3.6.1.2.1.95.3.1.12			A collection of optional objects providing high capacity data delivery sample data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcHCOctetDataGroup MUST also be implemented.
frsldPvcSampleHCFrameGroup	1.3.6.1.2.1.95.3.1.11			A collection of optional objects providing high capacity frame delivery sample data collected on a PVC which implements Service Level Definitions. If this group is implemented, frsldPvcHCFrameDataGroup MUST also be implemented.
frsldPvcSampleTable	1.3.6.1.2.1.95.1.4		not-accessible	The Frame Relay Service Level Definitions sample table.
G32 frsldPvcSmplDataDeliveredC	1.3.6.1.2.1.95.1.4.1.10	Gauge32	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCDataDeliveredC.
G32 frsldPvcSmplDataDeliveredE	1.3.6.1.2.1.95.1.4.1.11	Gauge32	read-only	The number of octets that were received at frsldPvcCtrlDeliveredRP and determined to have been sent in excess of the CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCDataDeliveredE.
G32 frsldPvcSmplDataOfferedC	1.3.6.1.2.1.95.1.4.1.12	Gauge32	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP within CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCDataOfferredC.
G32 frsldPvcSmplDataOfferedE	1.3.6.1.2.1.95.1.4.1.13	Gauge32	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP in excess of the CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCDataOfferedE.
G32 frsldPvcSmplDelayAvg	1.3.6.1.2.1.95.1.4.1.4	Gauge32	read-only	The average delay reported in microseconds measured for all delay packets that arrived during this interval. A value of zero means that no data is available.
G32 frsldPvcSmplDelayMax	1.3.6.1.2.1.95.1.4.1.3	Gauge32	read-only	The largest delay reported in microseconds measured for any information packet that arrived during this interval. A value of zero means that no data is available.
G32 frsldPvcSmplDelayMin	1.3.6.1.2.1.95.1.4.1.2	Gauge32	read-only	The minimum delay reported in microseconds measured for any information packet that arrived during this interval. A value of zero means that no data is available.
TIM frsldPvcSmplEndTime	1.3.6.1.2.1.95.1.4.1.25	TimeStamp	read-only	The value of sysUpTime when this sample interval ended. No data will be reported and the row will not appear in the table until the sample has been collected.
G32 frsldPvcSmplFrDeliveredC	1.3.6.1.2.1.95.1.4.1.6	Gauge32	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCFrDeliveredC.
G32 frsldPvcSmplFrDeliveredE	1.3.6.1.2.1.95.1.4.1.7	Gauge32	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCFrDeliveredE.
G32 frsldPvcSmplFrOfferedC	1.3.6.1.2.1.95.1.4.1.8	Gauge32	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP within CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCFrOfferedC.
G32 frsldPvcSmplFrOfferedE	1.3.6.1.2.1.95.1.4.1.9	Gauge32	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP in excess of the CIR during this interval. If it is the case that the high capacity counters are also used, this MUST report the value of the lower 32 bits of the CounterBasedGauge64 value of frsldPvcSmplHCFrOfferedE.
NUM frsldPvcSmplHCDataDeliveredC	1.3.6.1.2.1.95.1.4.1.18	CounterBasedGauge64	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR during this interval. This value is a 64-bit version of frsldPvcSmplDataDeliveredC.
NUM frsldPvcSmplHCDataDeliveredE	1.3.6.1.2.1.95.1.4.1.19	CounterBasedGauge64	read-only	The number of octets that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR during this interval. This value is a 64-bit version of frsldPvcSmplData- DeliveredE.
NUM frsldPvcSmplHCDataOfferedC	1.3.6.1.2.1.95.1.4.1.20	CounterBasedGauge64	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP within CIR during this interval. This value is a 64-bit version of frsldPvcSmplDataOfferedC.
NUM frsldPvcSmplHCDataOfferedE	1.3.6.1.2.1.95.1.4.1.21	CounterBasedGauge64	read-only	The number of octets that were offered through frsldPvcCtrlTransmitRP in excess of the CIR during this interval. This object is a 64-bit version of frsldPvcSmplDataOfferedE.
NUM frsldPvcSmplHCFrDeliveredC	1.3.6.1.2.1.95.1.4.1.14	CounterBasedGauge64	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent within CIR during this interval. This object is a 64-bit version of frsldPvcSmplFrDeliveredC.
NUM frsldPvcSmplHCFrDeliveredE	1.3.6.1.2.1.95.1.4.1.15	CounterBasedGauge64	read-only	The number of frames that were received at frsldPvcCtrlReceiveRP and determined to have been sent in excess of the CIR during this interval. This object is a 64-bit version of frsldPvcSmpl- FrDeliveredE.
NUM frsldPvcSmplHCFrOfferedC	1.3.6.1.2.1.95.1.4.1.16	CounterBasedGauge64	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP within CIR during this interval. This object is a 64-bit version of frsldPvcSmplFrOfferedC.
NUM frsldPvcSmplHCFrOfferedE	1.3.6.1.2.1.95.1.4.1.17	CounterBasedGauge64	read-only	The number of frames that were offered through frsldPvcCtrlTransmitRP in excess of the CIR during this interval. This object is a 64-bit version of frsldPvcSmplFrOfferedE.
I32 frsldPvcSmplIdx	1.3.6.1.2.1.95.1.4.1.1	Integer32	not-accessible	The bucket index of the current sample. This increments once for each new bucket in the table.
G32 frsldPvcSmplMissedPolls	1.3.6.1.2.1.95.1.4.1.5	Gauge32	read-only	The total number of polls that were missed during this interval.
TIM frsldPvcSmplStartTime	1.3.6.1.2.1.95.1.4.1.24	TimeStamp	read-only	The value of sysUpTime when this sample interval started.
G32 frsldPvcSmplUnavailables	1.3.6.1.2.1.95.1.4.1.23	Gauge32	read-only	The number of times this PVC was declared unavailable for any reason during this interval.
TIK frsldPvcSmplUnavailableTime	1.3.6.1.2.1.95.1.4.1.22	TimeTicks	read-only	The amount of time this PVC was declared unavailable for any reason during this interval.
BIT frsldRPCaps	1.3.6.1.2.1.95.2.3	Bits	read-only	This object specifies the reference points that the agent supports. This object allows the management application to discover which rows can be created on a specific device.
I32 frsldSmplCtrlBuckets	1.3.6.1.2.1.95.1.2.1.4	Integer32	read-create	The number of discrete buckets over which the data statistics are sampled. When this object is created or modified, the device SHOULD attempt to set the frsldSmplCtrlBuckets- Granted to a value as close as is possible depending upon the implementation and the available resources.
I32 frsldSmplCtrlBucketsGranted	1.3.6.1.2.1.95.1.2.1.5	Integer32	read-only	The number of discrete buckets granted. This object will return 0 until frsldSmplCtrlStatus is set to active(1). At that time the buckets will be allocated depending upon implementation and available resources.
I32 frsldSmplCtrlColPeriod	1.3.6.1.2.1.95.1.2.1.3	Integer32	read-create	The amount of time in seconds that defines a period of collection for the statistics. At the end of each period, the statistics will be sampled and a row is added to the sample table.
frsldSmplCtrlEntry	1.3.6.1.2.1.95.1.2.1		not-accessible	An entry in the Frame Relay Service Level Definitions sample control table.
I32 frsldSmplCtrlIdx	1.3.6.1.2.1.95.1.2.1.1	Integer32	not-accessible	The unique index for this row in the sample control table.
ROW frsldSmplCtrlStatus	1.3.6.1.2.1.95.1.2.1.2	RowStatus	read-create	The status of the current row. This object is used to add, delete, and disable rows in this table. This row SHOULD NOT be removed until the status is changed to destroy(6). When the status changes to active(1), the collection in the sample tables below will be activated. The rows added to this table MUST have a valid ifIndex, an ifType related to frame relay, frsldPvcCtrlDlci MUST exist for the specified ifIndex and frsldPvcCtrlStatus MUST have a value of active(1). The value of frsldPvcCtrlStatus MUST be active(1) to transition this object to active(1). If the value of frsldPvcCtrlStatus becomes anything other than active(1) when the state of this object is not active(1), this object SHOULD be set to notReady(3). The data in this table SHOULD persist through power cycles. The symantics of readiness for the rows still applies. This means that it is possible for a row to be reprovisioned as notReady(3) if the underlying DLCI does not persist.
frsldSmplCtrlTable	1.3.6.1.2.1.95.1.2		not-accessible	The Frame Relay Service Level Definitions sampling control table.
BIT frsldSmplCtrlWriteCaps	1.3.6.1.2.1.95.2.2	Bits	read-only	This object specifies the write capabilities for the read-create objects of the Sample Control table. If the corresponding bit is enabled (1), the agent supports writes to that object.

RFC description

Defines Frame Relay service level management and performance metrics (RFC 3202).

Start monitoring Vendor-neutral Frame Relay network equipment/carrier circuit, any manufacturer (FRF.13 service levels) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FRSLD-MIB