| OID symbolic | OID numeric | Type | Access | Description |
|---|
| frameRelayDTE | 1.3.6.1.2.1.10.32 | | | The MIB module to describe the use of a Frame Relay
interface by a DTE. |
| frameRelayTrapControl | 1.3.6.1.2.1.10.32.4 | | | |
| frameRelayTraps | 1.3.6.1.2.1.10.32.0 | | | |
| I32 frCircuitCommittedBurst | 1.3.6.1.2.1.10.32.2.1.12 | Integer32 | read-create | This variable indicates the maximum amount of data, in
bits, that the network agrees to transfer under normal
conditions, during the measurement interval. |
| TIM frCircuitCreationTime | 1.3.6.1.2.1.10.32.2.1.10 | TimeStamp | read-only | The value of sysUpTime when the virtual circuit was
created, whether by the Data Link Connection Management
Interface or by a SetRequest. |
| C32 frCircuitDiscards | 1.3.6.1.2.1.10.32.2.1.17 | Counter32 | read-only | The number of inbound frames dropped because of format
errors, or because the VC is inactive. |
| DLC frCircuitDlci | 1.3.6.1.2.1.10.32.2.1.2 | DLCI | read-only | The Data Link Connection Identifier for this virtual
circuit. |
| frCircuitEntry | 1.3.6.1.2.1.10.32.2.1 | | not-accessible | The information regarding a single Data Link
Connection. Discontinuities in the counters contained
in this table are indicated by the value in
frCircuitCreationTime. |
| I32 frCircuitExcessBurst | 1.3.6.1.2.1.10.32.2.1.13 | Integer32 | read-create | This variable indicates the maximum amount of
uncommitted data bits that the network will attempt to
deliver over the measurement interval.
By default, if not configured when creating the entry,
the Excess Information Burst Size is set to the value
of ifSpeed. |
| frCircuitGroup | 1.3.6.1.2.1.10.32.6.1.2 | | | The objects necessary to control the Virtual Circuits
layered onto a Frame Relay Interface. |
| frCircuitGroup0 | 1.3.6.1.2.1.10.32.6.1.7 | | | The objects necessary to control the Virtual Circuits
layered onto a Frame Relay Interface from RFC 1315. |
| NUM frCircuitIfIndex | 1.3.6.1.2.1.10.32.2.1.1 | InterfaceIndex | read-only | The ifIndex Value of the ifEntry this virtual circuit
is layered onto. |
| TIM frCircuitLastTimeChange | 1.3.6.1.2.1.10.32.2.1.11 | TimeStamp | read-only | The value of sysUpTime when last there was a change in
the virtual circuit state |
| NUM frCircuitLogicalIfIndex | 1.3.6.1.2.1.10.32.2.1.20 | InterfaceIndex | read-create | Normally the same value as frDlcmiIfIndex, but
different when an implementation associates a virtual
ifEntry with a DLC or set of DLCs in order to associate
higher layer objects such as the ipAddrEntry with a
subset of the virtual circuits on a Frame Relay
interface. The type of such ifEntries is defined by the
higher layer object; for example, if PPP/Frame Relay is
implemented, the ifType of this ifEntry would be PPP.
If it is not so defined, as would be the case with an
ipAddrEntry, it should be of type Other. |
| INT frCircuitMulticast | 1.3.6.1.2.1.10.32.2.1.15 | INTEGER | read-create | This indicates whether this VC is used as a unicast VC
(i.e. not multicast) or the type of multicast service
subscribed to |
| C32 frCircuitReceivedBECNs | 1.3.6.1.2.1.10.32.2.1.5 | Counter32 | read-only | Number of frames received from the network indicating
backward congestion since the virtual circuit was
created. This occurs when the remote DTE sets the BECN
flag, or when a switch in the network receives the
frame from a trunk whose transmission queue is
congested. |
| C32 frCircuitReceivedDEs | 1.3.6.1.2.1.10.32.2.1.18 | Counter32 | read-only | Number of frames received from the network indicating
that they were eligible for discard since the virtual
circuit was created. This occurs when the remote DTE
sets the DE flag, or when in remote DTE's switch
detects that the frame was received as Excess Burst
data. |
| C32 frCircuitReceivedFECNs | 1.3.6.1.2.1.10.32.2.1.4 | Counter32 | read-only | Number of frames received from the network indicating
forward congestion since the virtual circuit was
created. This occurs when the remote DTE sets the FECN
flag, or when a switch in the network enqueues the
frame to a trunk whose transmission queue is
congested. |
| C32 frCircuitReceivedFrames | 1.3.6.1.2.1.10.32.2.1.8 | Counter32 | read-only | Number of frames received over this virtual circuit
since it was created. |
| C32 frCircuitReceivedOctets | 1.3.6.1.2.1.10.32.2.1.9 | Counter32 | read-only | Number of octets received over this virtual circuit
since it was created. Octets counted include the full
frame relay header, but do not include the flag
characters or the CRC. |
| ROW frCircuitRowStatus | 1.3.6.1.2.1.10.32.2.1.21 | RowStatus | read-create | This object is used to create a new row or modify or
destroy an existing row in the manner described in the
definition of the RowStatus textual convention.
Writable objects in the table may be written in any
RowStatus state. |
| C32 frCircuitSentDEs | 1.3.6.1.2.1.10.32.2.1.19 | Counter32 | read-only | Number of frames sent to the network indicating that
they were eligible for discard since the virtual
circuit was created. This occurs when the local DTE
sets the DE flag, indicating that during Network
congestion situations those frames should be discarded
in preference of other frames sent without the DE bit
set. |
| C32 frCircuitSentFrames | 1.3.6.1.2.1.10.32.2.1.6 | Counter32 | read-only | The number of frames sent from this virtual circuit
since it was created. |
| C32 frCircuitSentOctets | 1.3.6.1.2.1.10.32.2.1.7 | Counter32 | read-only | The number of octets sent from this virtual circuit
since it was created. Octets counted are the full
frame relay header and the payload, but do not include
the flag characters or CRC. |
| INT frCircuitState | 1.3.6.1.2.1.10.32.2.1.3 | INTEGER | read-create | Indicates whether the particular virtual circuit is
operational. In the absence of a Data Link Connection
Management Interface, virtual circuit entries (rows)
may be created by setting virtual circuit state to
'active', or deleted by changing Circuit state to
'invalid'.
Whether or not the row actually disappears is left to
the implementation, so this object may actually read as
'invalid' for some arbitrary length of time. It is
also legal to set the state of a virtual circuit to
'inactive' to temporarily disable a given circuit.
The use of 'invalid' is deprecated in this SNMP Version
2 MIB, in favor of frCircuitRowStatus. |
| frCircuitTable | 1.3.6.1.2.1.10.32.2 | | not-accessible | A table containing information about specific Data
Link Connections (DLC) or virtual circuits. |
| I32 frCircuitThroughput | 1.3.6.1.2.1.10.32.2.1.14 | Integer32 | read-create | Throughput is the average number of 'Frame Relay
Information Field' bits transferred per second across a
user network interface in one direction, measured over
the measurement interval.
If the configured committed burst rate and throughput
are both non-zero, the measurement interval, T, is
T=frCircuitCommittedBurst/frCircuitThroughput.
If the configured committed burst rate and throughput
are both zero, the measurement interval, T, is
T=frCircuitExcessBurst/ifSpeed. |
| INT frCircuitType | 1.3.6.1.2.1.10.32.2.1.16 | INTEGER | read-only | Indication of whether the VC was manually created
(static), or dynamically created (dynamic) via the data
link control management interface. |
| frCompliance | 1.3.6.1.2.1.10.32.6.2.1 | | | The compliance statement |
| frCompliance0 | 1.3.6.1.2.1.10.32.6.2.2 | | | The compliance statement for objects and the trap
defined in RFC 1315. |
| frCompliances | 1.3.6.1.2.1.10.32.6.2 | | | |
| frConformance | 1.3.6.1.2.1.10.32.6 | | | |
| NTF frDLCIStatusChange | 1.3.6.1.2.1.10.32.0.1 | | | This trap indicates that the indicated Virtual Circuit
has changed state. It has either been created or
invalidated, or has toggled between the active and
inactive states. If, however, the reason for the state
change is due to the DLCMI going down, per-DLCI traps
should not be generated. |
| INT frDlcmiAddress | 1.3.6.1.2.1.10.32.1.1.3 | INTEGER | read-create | This variable states which address format is in use on
the Frame Relay interface. |
| INT frDlcmiAddressLen | 1.3.6.1.2.1.10.32.1.1.4 | INTEGER | read-create | This variable states the address length in octets. In
the case of Q922 format, the length indicates the
entire length of the address including the control
portion. |
| frDlcmiEntry | 1.3.6.1.2.1.10.32.1.1 | | not-accessible | The Parameters for a particular Data Link Connection
Management Interface. |
| I32 frDlcmiErrorThreshold | 1.3.6.1.2.1.10.32.1.1.7 | Integer32 | read-create | This is the maximum number of unanswered Status
Enquiries the equipment shall accept before declaring
the interface down. |
| I32 frDlcmiFullEnquiryInterval | 1.3.6.1.2.1.10.32.1.1.6 | Integer32 | read-create | Number of status enquiry intervals that pass before
issuance of a full status enquiry message. |
| NUM frDlcmiIfIndex | 1.3.6.1.2.1.10.32.1.1.1 | InterfaceIndex | read-only | The ifIndex value of the corresponding ifEntry. |
| DLC frDlcmiMaxSupportedVCs | 1.3.6.1.2.1.10.32.1.1.9 | DLCI | read-create | The maximum number of Virtual Circuits allowed for
this interface. Usually dictated by the Frame Relay
network.
In response to a SET, if a value less than zero or
higher than the agent's maximal capability is
configured, the agent should respond badValue |
| I32 frDlcmiMonitoredEvents | 1.3.6.1.2.1.10.32.1.1.8 | Integer32 | read-create | This is the number of status polling intervals over
which the error threshold is counted. For example, if
within 'MonitoredEvents' number of events the station
receives 'ErrorThreshold' number of errors, the
interface is marked as down. |
| INT frDlcmiMulticast | 1.3.6.1.2.1.10.32.1.1.10 | INTEGER | read-create | This indicates whether the Frame Relay interface is
using a multicast service. |
| I32 frDlcmiPollingInterval | 1.3.6.1.2.1.10.32.1.1.5 | Integer32 | read-create | This is the number of seconds between successive
status enquiry messages. |
| ROW frDlcmiRowStatus | 1.3.6.1.2.1.10.32.1.1.12 | RowStatus | read-create | SNMP Version 2 Row Status Variable. Writable objects
in the table may be written in any RowStatus state. |
| INT frDlcmiState | 1.3.6.1.2.1.10.32.1.1.2 | INTEGER | read-create | This variable states which Data Link Connection
Management scheme is active (and by implication, what
DLCI it uses) on the Frame Relay interface. |
| INT frDlcmiStatus | 1.3.6.1.2.1.10.32.1.1.11 | INTEGER | read-only | This indicates the status of the Frame Relay interface
as determined by the performance of the dlcmi. If no
dlcmi is running, the Frame Relay interface will stay
in the running state indefinitely. |
| frDlcmiTable | 1.3.6.1.2.1.10.32.1 | | not-accessible | The Parameters for the Data Link Connection Management
Interface for the frame relay service on this
interface. |
| OCT frErrData | 1.3.6.1.2.1.10.32.3.1.3 | OCTET STRING | read-only | An octet string containing as much of the error packet
as possible. As a minimum, it must contain the Q.922
Address or as much as was delivered. It is desirable
to include all header and demultiplexing information. |
| frErrEntry | 1.3.6.1.2.1.10.32.3.1 | | not-accessible | The error information for a single frame relay
interface. |
| C32 frErrFaults | 1.3.6.1.2.1.10.32.3.1.5 | Counter32 | read-only | The number of times the interface has gone down since
it was initialized. |
| TIM frErrFaultTime | 1.3.6.1.2.1.10.32.3.1.6 | TimeStamp | read-only | The value of sysUpTime at the time when the interface
was taken down due to excessive errors. Excessive
errors is defined as the time when a DLCMI exceeds the
frDlcmiErrorThreshold number of errors within
frDlcmiMonitoredEvents. See FrDlcmiEntry for further
details. |
| frErrGroup | 1.3.6.1.2.1.10.32.6.1.4 | | | Objects designed to assist in debugging Frame Relay
Interfaces. |
| frErrGroup0 | 1.3.6.1.2.1.10.32.6.1.8 | | | Objects designed to assist in debugging Frame Relay
Interfaces from RFC 1315. |
| NUM frErrIfIndex | 1.3.6.1.2.1.10.32.3.1.1 | InterfaceIndex | read-only | The ifIndex Value of the corresponding ifEntry. |
| frErrTable | 1.3.6.1.2.1.10.32.3 | | not-accessible | A table containing information about Errors on the
Frame Relay interface. Discontinuities in the counters
contained in this table are the same as apply to the
ifEntry associated with the Interface. |
| TIM frErrTime | 1.3.6.1.2.1.10.32.3.1.4 | TimeStamp | read-only | The value of sysUpTime at which the error was
detected. |
| INT frErrType | 1.3.6.1.2.1.10.32.3.1.2 | INTEGER | read-only | The type of error that was last seen on this interface:
receiveShort: frame was not long enough to allow
demultiplexing - the address field was incomplete,
or for virtual circuits using Multiprotocol over
Frame Relay, the protocol identifier was missing
or incomplete.
receiveLong: frame exceeded maximum length configured for this
interface.
illegalAddress: address field did not match configured format.
unknownAddress: frame received on a virtual circuit which was not
active or administratively disabled.
dlcmiProtoErr: unspecified error occurred when attempting to
interpret link maintenance frame.
dlcmiUnknownIE: link maintenance frame contained an Information
Element type which is not valid for the
configured link maintenance protocol.
dlcmiSequenceErr: link maintenance frame contained a sequence
number other than the expected value.
dlcmiUnknownRpt: link maintenance frame contained a Report Type
Information Element whose value was not valid
for the configured link maintenance protocol.
noErrorSinceReset: no errors have been detected since the last
cold start or warm start. |
| frGroups | 1.3.6.1.2.1.10.32.6.1 | | | |
| frNotificationGroup | 1.3.6.1.2.1.10.32.6.1.5 | | | Traps which may be used to enhance event driven
management of the interface. |
| frPortGroup | 1.3.6.1.2.1.10.32.6.1.1 | | | The objects necessary to control the Link Management
Interface for a Frame Relay Interface as well as
maintain the error statistics on this interface. |
| frPortGroup0 | 1.3.6.1.2.1.10.32.6.1.6 | | | The objects necessary to control the Link Management
Interface for a Frame Relay Interface as well as
maintain the error statistics on this interface from
RFC 1315. |
| frTrapGroup | 1.3.6.1.2.1.10.32.6.1.3 | | | The objects necessary to control a Frame Relay
Interface's notification messages. |
| frTrapGroup0 | 1.3.6.1.2.1.10.32.6.1.9 | | | The objects necessary to control a Frame Relay
Interface's notification messages from RFC 1315. |
| I32 frTrapMaxRate | 1.3.6.1.2.1.10.32.4.2 | Integer32 | read-write | This variable indicates the number of milliseconds
that must elapse between trap emissions. If events
occur more rapidly, the impementation may simply fail
to trap, or may queue traps until an appropriate time. |
| INT frTrapState | 1.3.6.1.2.1.10.32.4.1 | INTEGER | read-write | This variable indicates whether the system produces
the frDLCIStatusChange trap. |
