GDSFrameRelay-MIB

All MIBs › GDSFrameRelay-MIB

Category: Domain: WAN/TDM, Frame Relay

Description: GDS Frame Relay MIB for managing Frame Relay virtual circuits, DLCI configuration, and traffic statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GDSFrameRelay-MIB?

GDSFrameRelay-MIB is a vendor MIB for GDS Frame Relay equipment, covering configuration and monitoring of Frame Relay virtual circuits, including DLCI assignment and per-circuit traffic statistics. It exposes the typical Frame Relay management data set: DLCI configuration, committed information rate settings, and traffic counters per virtual circuit, used to track the operational and performance status of provisioned Frame Relay PVCs. Its monitoring role is centered on circuit-level software/traffic status rather than physical hardware sensors: tracking whether a DLCI is active, its discard-eligible frame counts, and congestion notifications helps identify a PVC that is oversubscribed, misconfigured, or down. It likely complements the standard Frame Relay DTE/DCE interface MIB (RFC 1315) for baseline Frame Relay statistics. It is deployed on GDS Frame Relay access devices terminating leased-line or Frame Relay carrier circuits. Engineers can download the GDSFrameRelay-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GDSFrameRelay-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

GDS Frame Relay access device

Monitoring Examples

No object or table names were extracted for this module, so a concrete polling example cannot be grounded in real identifiers; in general use, an administrator would monitor per-DLCI traffic counters and status flags to confirm a virtual circuit is active and not experiencing congestion, with a DLCI reporting inactive or a spike in discard-eligible frames signaling a circuit or provisioning problem.

What Can Be Monitored

DLCI configuration and status
per-circuit traffic statistics
committed information rate settings
congestion/discard-eligible frame counts

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
configure	1.3.6.1.4.1.1955.5.5.3
fR_RX_Err_Entry	1.3.6.1.4.1.1955.5.5.2.3.1		not-accessible
fR_RX_Err_Table	1.3.6.1.4.1.1955.5.5.2.3		not-accessible	The receive error information for a frame relay encryptor frame relay port.
fR_Traffic_Entry	1.3.6.1.4.1.1955.5.5.2.2.1		not-accessible
fR_Traffic_Table	1.3.6.1.4.1.1955.5.5.2.2		not-accessible	The Statistics Table for the frame relay encryptor .
frame_relay	1.3.6.1.4.1.1955.5.5.2
CTR frBad_Frames	1.3.6.1.4.1.1955.5.5.2.2.1.4	Counter	read-only	The number of bad frames received by the frame relay encryptor on a port. These are classified further in frRxErrTable.
CTR frDropped_Frames	1.3.6.1.4.1.1955.5.5.2.2.1.9	Counter	read-only	The total number of TX frames dropped by the frame relay encryptor on a port.
CTR frGood_Frames	1.3.6.1.4.1.1955.5.5.2.2.1.3	Counter	read-only	The total number of frames received by the frame relay encryptor on a port.
CTR frInactive_DLCI	1.3.6.1.4.1.1955.5.5.2.2.1.5	Counter	read-only	The number of illegal or unknown DLCIs received by the frame relay encryptor on a port.
INT frPort_Index	1.3.6.1.4.1.1955.5.5.2.2.1.1	INTEGER	read-only	Port Number Index. The ifIndex Value of the corresponding ifEntry from rfc1213.
INT frPort_Type	1.3.6.1.4.1.1955.5.5.2.2.1.2	INTEGER	read-only	Plain is on the local side, cipher the network
CTR frReceived_BECN	1.3.6.1.4.1.1955.5.5.2.2.1.7	Counter	read-only	The number of frames with a backward congestion notification received by the frame relay encryptor on a port.
CTR frReceived_FECN	1.3.6.1.4.1.1955.5.5.2.2.1.6	Counter	read-only	The number of frames with a forward congestion notification received by the frame relay encryptor on a port.
CTR frRxErrAborted_Frames	1.3.6.1.4.1.1955.5.5.2.3.1.3	Counter	read-only	The number of aborted frames received.
CTR frRxErrCRC_Errors	1.3.6.1.4.1.1955.5.5.2.3.1.6	Counter	read-only	The number of CRC errors received.
INT frRxErrIndex	1.3.6.1.4.1.1955.5.5.2.3.1.1	INTEGER	read-only	Port Number Index. The ifIndex Value of the corresponding ifEntry from rfc1213.
CTR frRxErrOverruns	1.3.6.1.4.1.1955.5.5.2.3.1.5	Counter	read-only	The number of overruns received.
CTR frRxErrResidual_Bits	1.3.6.1.4.1.1955.5.5.2.3.1.4	Counter	read-only	The number of residual bit frames received.
CTR frRxErrShort_Frames	1.3.6.1.4.1.1955.5.5.2.3.1.2	Counter	read-only	The number of short frames received.
CTR frSent_Frames	1.3.6.1.4.1.1955.5.5.2.2.1.8	Counter	read-only	The total number of frames transmitted by the frame relay encryptor on a port.
gds	1.3.6.1.4.1.1955
is_GDS_frame_relay_device5	1.3.6.1.4.1.1955.5.5
pi_App_DLC_Cipher_Entry	1.3.6.1.4.1.1955.5.5.3.6.1.1		not-accessible
pi_App_DLC_Cipher_Table	1.3.6.1.4.1.1955.5.5.3.6.1		not-accessible	The table of encrypted DLCIs port.
pi_FR_DLC_Ranges_Entry	1.3.6.1.4.1.1955.5.5.3.3.1		not-accessible
pi_FR_DLC_Ranges_Table	1.3.6.1.4.1.1955.5.5.3.3		not-accessible	The Table of Active DLCIs.
pi_FR_Layer1	1.3.6.1.4.1.1955.5.5.3.1
pi_FR_Layer2	1.3.6.1.4.1.1955.5.5.3.2
INT pi_FR_LMI_support	1.3.6.1.4.1.1955.5.5.3.2.4	INTEGER	read-write	LMI version
INT pi_FR_Logical_Interface_Type	1.3.6.1.4.1.1955.5.5.3.2.1	INTEGER	read-only	The type of Frame Relay logical interface. UNI = User to Network Interface NNI = Network to Network Interface
INT pi_FR_Max_RX_Frame	1.3.6.1.4.1.1955.5.5.3.2.2	INTEGER	read-write	Maximum frame length in octets incoming
INT pi_FR_Max_TX_Frame	1.3.6.1.4.1.1955.5.5.3.2.3	INTEGER	read-write	Maximum frame length in octets outgoing
pi_Remote_Port1	1.3.6.1.4.1.1955.5.5.3.5.1
IP pi_Remote_Port1Gateway_Address	1.3.6.1.4.1.1955.5.5.3.5.1.3	IpAddress	read-write	The Gateway IP address for 1. The gateway is on the same network as the port, so the network bits must be identical to the port Ipaddress
IP pi_Remote_Port1IP_Address	1.3.6.1.4.1.1955.5.5.3.5.1.1	IpAddress	read-write	The IP address for 1, the Ethernet line
IP pi_Remote_Port1Subnet_mask	1.3.6.1.4.1.1955.5.5.3.5.1.2	IpAddress	read-write	The subnet mask associated with the IP address of the 1 Ethernet line. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
pi_Remote_Port3	1.3.6.1.4.1.1955.5.5.3.5.3
INT pi_Remote_Port3Baudrate	1.3.6.1.4.1.1955.5.5.3.5.3.5	INTEGER	read-write	The Baud rate for async port 3. The other physical parameters are fixed as follows: Character Length: 8 bits Parity: none Stopbits: 1
INT pi_Remote_Port3Data_link_protocol	1.3.6.1.4.1.1955.5.5.3.5.3.4	INTEGER	read-only	The type of Data link protocol. Currently only slip is supported
IP pi_Remote_Port3Gateway_Address	1.3.6.1.4.1.1955.5.5.3.5.3.3	IpAddress	read-write	The Gateway IP address for 3. The gateway is on the same network as the port, so the network bits must be identical to the port Ipaddress
IP pi_Remote_Port3IP_Address	1.3.6.1.4.1.1955.5.5.3.5.3.1	IpAddress	read-write	The IP address for 1, the serial line
IP pi_Remote_Port3Subnet_mask	1.3.6.1.4.1.1955.5.5.3.5.3.2	IpAddress	read-write	The subnet mask associated with the IP address of the 3 serial line. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
INT piAppDLcCipherBand	1.3.6.1.4.1.1955.5.5.3.6.1.1.1	INTEGER	read-only	The index number of this DLCI circuit band.
INT piAppDLcCipherEnd_set_to_activate_changes	1.3.6.1.4.1.1955.5.5.3.6.1.1.4	INTEGER	read-write	The last DLCI in this band Setting this parameter activates the changes
INT piAppDLcCipherStart	1.3.6.1.4.1.1955.5.5.3.6.1.1.3	INTEGER	read-write	The first DLCI in this band
INT piAppDLcCipherUse	1.3.6.1.4.1.1955.5.5.3.6.1.1.2	INTEGER	read-write	The Type of use (plain or cipher) to be applied to the range defined in piAppDLcCipherStart and piAppDLcCipherEnd.
piApplication	1.3.6.1.4.1.1955.5.5.3.6
INT piFRDLcRangeBand	1.3.6.1.4.1.1955.5.5.3.3.1.1	INTEGER	read-only	The index number of this DLCI circuit band.
INT piFRDLcRangeEnd_set_to_activate_changes	1.3.6.1.4.1.1955.5.5.3.3.1.5	INTEGER	read-write	The last DLCI in this band Setting this parameter activates the changes
INT piFRDLcRangeMode	1.3.6.1.4.1.1955.5.5.3.3.1.3	INTEGER	read-only	For future use
INT piFRDLcRangeStart	1.3.6.1.4.1.1955.5.5.3.3.1.4	INTEGER	read-write	The first DLCI in this band
INT piFRDLcRangeUse	1.3.6.1.4.1.1955.5.5.3.3.1.2	INTEGER	read-write	The Type of use to be applied to the range defined in piFRDLcRangeStart and piFRDLcRangeEnd
INT piFRE1_Cipher_Port_Impedance	1.3.6.1.4.1.1955.5.5.3.1.4	INTEGER	read-write
INT piFRE1_Framing_Mode	1.3.6.1.4.1.1955.5.5.3.1.5	INTEGER	read-write
INT piFRE1_Plain_Port_Impedance	1.3.6.1.4.1.1955.5.5.3.1.3	INTEGER	read-write
INT piFRE1_Time_Slot_Options	1.3.6.1.4.1.1955.5.5.3.1.6	INTEGER	read-write	Required if the physical type is G703 (E1) E1 time slot options available: Bit values shown in piFRE1-Time-Slots all slots, except TS0 0xff, 0xff, 0xff, 0xfe all slots, except TS0,TS16 0xff, 0xfe, 0xff, 0xfe
OCT piFRE1_Time_Slots	1.3.6.1.4.1.1955.5.5.3.1.7	OCTET STRING	read-only	An Octet bit string. Each bit defines an E1 time slot: 0= not used for frame relay 1= used for frame relay
INT piFRInterface_Installed	1.3.6.1.4.1.1955.5.5.3.1.1	INTEGER	read-only	The type of Frame Relay Physical interface. The following parameters are required for: - RS422/V35/X21 clock source - G703 E1 impedance, framemode, timeslots - T1 T1 frame mode, timeslots.
INT piFRT1_Cipher_Port_Pulse	1.3.6.1.4.1.1955.5.5.3.1.9	INTEGER	read-write
INT piFRT1_Framing_Mode	1.3.6.1.4.1.1955.5.5.3.1.10	INTEGER	read-write
INT piFRT1_Plain_Port_Pulse	1.3.6.1.4.1.1955.5.5.3.1.8	INTEGER	read-write
INT piFRT1_Time_Slot_Options	1.3.6.1.4.1.1955.5.5.3.1.11	INTEGER	read-write	Required if the physical type is T1 T1 time slot options available: Bit values shown in piFRT1TimeSlots all slots 0xff, 0xff, 0xff
OCT piFRT1_Time_Slots	1.3.6.1.4.1.1955.5.5.3.1.12	OCTET STRING	read-only	An Octet bit string. Each bit defines a T1 time slot: 0= not used for frame relay 1= used for frame relay
INT piFRTX_Clock_Source	1.3.6.1.4.1.1955.5.5.3.1.2	INTEGER	read-write	Required if the physical type is: RS422 V.35 X.21
piRemotePort2	1.3.6.1.4.1.1955.5.5.3.5.2
piRemotePorts	1.3.6.1.4.1.1955.5.5.3.5
INT reset_FR_statistic_counters	1.3.6.1.4.1.1955.5.5.2.1	INTEGER	read-write	This command clears all the frame relay statistical counters for both ports.
seriesfr	1.3.6.1.4.1.1955.5
STR uAccess_Table	1.3.6.1.4.1.1955.5.5.1.1.6	DisplayString	read-only	The frame relay encryptor access control table version.
STR uAlgorithm	1.3.6.1.4.1.1955.5.5.1.1.5	DisplayString	read-only	The frame relay encryptor encryption algorithm DES or GDS.
uBackground	1.3.6.1.4.1.1955.5.5.1.4
STR uComm_HW_Version	1.3.6.1.4.1.1955.5.5.1.1.2	DisplayString	read-only	The frame relay encryptor commsboard HW version.
STR uComm_SW_Version	1.3.6.1.4.1.1955.5.5.1.1.4	DisplayString	read-only	The frame relay encryptor comms board SW version.
INT uComms_State	1.3.6.1.4.1.1955.5.5.1.3.4	INTEGER	read-only	The current state of the frame relay encryptor comms board.
uConfigured	1.3.6.1.4.1.1955.5.5.1.2
STR uCurrent_Date	1.3.6.1.4.1.1955.5.5.1.3.1	DisplayString	read-write	The uCurrentTime indicates the current date of the frame relay encryptor . Date is in the format dd/mm/yy.
STR uCurrent_Time	1.3.6.1.4.1.1955.5.5.1.3.2	DisplayString	read-write	The uCurrentTime indicates the current time of the frame relay encryptor . Time is in the format hh:mm.
INT uDevice_State	1.3.6.1.4.1.1955.5.5.1.3.3	INTEGER	read-only	The current state of the frame relay encryptor . There are two test states: test-empty with no security parameters loaded test-loaded which is entered with live parameters from the live state
uDynamic	1.3.6.1.4.1.1955.5.5.1.3
STR uMain_HW_Version	1.3.6.1.4.1.1955.5.5.1.1.1	DisplayString	read-only	The frame relay encryptor mainboard HW version.
STR uMain_SW_Version	1.3.6.1.4.1.1955.5.5.1.1.3	DisplayString	read-only	The frame relay encryptor mainboard SW version. Every effort will be made by GDS to make the MIB backwards compatible to the frame relay encryptor software. In case of doubt or queries please quote the following release number. Enterprise MIB Version Release V1.8p
unit	1.3.6.1.4.1.1955.5.5.1
INT uNMS_State	1.3.6.1.4.1.1955.5.5.1.3.5	INTEGER	read-only	The current state of the SNMP agent for NMS requests. Only in the writeenabled state are Sets allowed.
INT uOwn_SID	1.3.6.1.4.1.1955.5.5.1.2.1	INTEGER	read-only	The Station Identity of this frame relay encryptor .
CTR uRAG_fails	1.3.6.1.4.1.1955.5.5.1.4.2	Counter	read-only	The total number of Random Number Generator failures recorded
CTR uRAG_tests	1.3.6.1.4.1.1955.5.5.1.4.1	Counter	read-only	The total number of Random Number Generator tests made A test is made once per minute.
CTR uRAG_threshold	1.3.6.1.4.1.1955.5.5.1.4.3	Counter	read-write	The number of failures that should trigger a Trap. Changing this value also clears the tests and fails counters
INT uReady_Alarm_Led	1.3.6.1.4.1.1955.5.5.1.3.7	INTEGER	read-only	The state of the front panel LED red: GRETACODER is in Test Mode green: GRETACODER is in Normal Mode yellow: GRETACODER is performing a self test blinking-red: GRETACODER is in Failure state blinking-yellow: GRETACODER MMI user is logged-in
INT uSM_State	1.3.6.1.4.1.1955.5.5.1.3.6	INTEGER	read-only	The current state of the Right SM module. This should be checked after parameter updates in the configure group or the MIBII system group.
uVersion_Strings	1.3.6.1.4.1.1955.5.5.1.1

RFC description

Vendor-proprietary MIB for frame relay interface management on Global Data Systems network equipment.

Start monitoring GDS Frame Relay access device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GDSFrameRelay-MIB

What Is GDSFrameRelay-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description