All MIBs › FRDTE-OPT-MIB
Category: Frame Relay
Description: Frame Relay DTE optional extensions MIB providing user-side management objects for Frame Relay data terminal equipment interface configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is FRDTE-OPT-MIB?
FRDTE-OPT-MIB is a Codex/Motorola-lineage vendor MIB providing user-side (DTE) optional management extensions for Frame Relay interfaces on CDX-6500-series equipment, mirroring the DCE-side FRDCE-OPT-MIB. It exposes station-level protocol group configuration objects for the customer/terminal side of a Frame Relay link. Its monitoring value is primarily configuration-status oriented, allowing an administrator to verify the DTE station's protocol group setting matches what the network side expects, which affects whether the frame relay circuit establishes and passes traffic correctly. It shares its object structure and dependency with the companion FRDCE-OPT-MIB and FRI-OPT-MIB modules covering the same CDX-6500 device family. It is used in legacy Frame Relay WAN deployments on the customer-premises (DTE) end of a Codex CDX-6500 connection. Engineers can download the FRDTE-OPT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in FRDTE-OPT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Codex CDX-6500 Frame Relay access device (DTE/customer-premises side)
Monitoring Examples
An administrator polling cdx6500PCTStationProtocolGroup and cdx6500PSTStationProtocolGroup on the DTE-side device can confirm the station protocol group configuration matches the DCE-side network equipment, helping diagnose a Frame Relay circuit that fails to come up due to a protocol group mismatch between customer and network equipment.
What Can Be Monitored
- Frame Relay DTE station protocol group configuration
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises | |
| mgmt |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| codex | 1.3.6.1.4.1.449 | |||
| cdxProductSpecific | 1.3.6.1.4.1.449.2 | |||
| cdx6500 | 1.3.6.1.4.1.449.2.1 | |||
| cdx6500Configuration | 1.3.6.1.4.1.449.2.1.2 | |||
| cdx6500CfgProtocolGroup | 1.3.6.1.4.1.449.2.1.2.1 | |||
| cdx6500PCTPortProtocolGroup | 1.3.6.1.4.1.449.2.1.2.1.1 | |||
| cdx6500PCTFRDTEPortTable | 1.3.6.1.4.1.449.2.1.2.1.1.5 | not-accessible | All of the configuration parameters relevant to the Frame Relay DTE Port table. | |
| cdx6500PCTFRDTEPortEntry | 1.3.6.1.4.1.449.2.1.2.1.1.5.1 | not-accessible | A row of FRI Port configuration parameters. | |
| INT cdx6500frdtepCfgPortNum | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.1 | INTEGER | read-only | Specifies the Port number for the Frame Relay Interface port you are selecting. |
| INT cdx6500frdtepConnectionType | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.2 | INTEGER | read-write | Specify the control signal handshake and clocking required for a connection to be made to this port: simp - simple, no control signals required dtr - dedicated, require the data terminal ready signal (DTR) simpb - simple, no control signals required for data transmission and reception. By default output leads will be low. nc - Skipped during configuration. |
| INT cdx6500frdtepClockSource | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.3 | INTEGER | read-write | int - internal clock source ext - external clock source extint - Internal receive and external transmit clock source (DCE only). extlp - external receive and loopback transmit clock source (DTE only). EXTLP must be configured in conjunction with EXTINT. nc - Skipped during configuration. |
| INT cdx6500frdtepClockSpeed | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.4 | INTEGER | read-write | This is the speed of the port in bits per second, when using internal clocking. The highest available speed is dependent on the card type,and on the interface type. |
| INT cdx6500frdtepMaxStations | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.5 | INTEGER | read-only | This is the highest station number to be configured on this FRI port. It is used to limit the configuration of stations. |
| INT cdx6500frdtepFrameSeqCounting | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.6 | INTEGER | read-only | Port uses normal or extended frame sequence numbering: normal - normal sequencing (modulo 8) ext - extended sequencing (modulo 128) nc - Skipped during configuration. All stations on this port will be set to this value. |
| INT cdx6500frdtepPktSeqCounting | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.7 | INTEGER | read-write | Port uses normal or extended packet level sequence numbers normal - normal sequencing (Modulo 8) ext - extended sequencing (Modulo 128) nc - Skipped during configuration. This parameter must be set to the same value at both this FRI port and the remote FRI port. All stations on this port will be set to this value. |
| INT cdx6500frdtepCtrlProtocol | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.8 | INTEGER | read-write | Whether ANSI T1.617 Annex D or LMI Support is enabled none - None is enabled. annexD - Annex D is enabled lmi - LMI is enabled. annexA - Annex A is enabled. auto - Auto-learn the Network control protocol type nc - Skipped during configuration. |
| INT cdx6500frdtepT391 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.9 | INTEGER | read-write | This parameter is the Link Integrity Verification Timer polling period. The FRI port sends status enquiry messages to network every T391/nT1 seconds. |
| INT cdx6500frdtepT392 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.10 | INTEGER | read-only | This parameter is the polling Cycle Verification Timer period. The FRI port expects status enquiry messages every T392/nT2 seconds. This parameter must be set to a value greater than N391/nT1, and applies only in bi-directional mode. |
| INT cdx6500frdtepN391 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.12 | INTEGER | read-write | Full Status polling cycle. FRI port sends Full status enquiry messages to network every nN1 polls. |
| INT cdx6500frdtepN392 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.13 | INTEGER | read-only | Error inactivity threshold. Number of errors during NN3 events that cause the station to be declared inactive. Should be less than or equal to nN3. |
| INT cdx6500frdtepN393 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.14 | INTEGER | read-write | Monitored events count for measuring nN3. nN2 errors during nN3 events will cause the station to be declared inactive. Should be greater than nN3. |
| INT cdx6500frdtepNT1 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.15 | INTEGER | read-write | This parameter is the Link Integrity Verification Timer polling period. The FRI port sends status enquiry messages to network every T391/nT1 seconds. |
| INT cdx6500frdtepNT2 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.16 | INTEGER | read-only | This parameter is the polling Cycle Verification Timer period. The FRI port expects status enquiry messages every T392/nT2 seconds. This parameter must be set to a value greater than N391/nT1, and applies only in bi-directional mode. |
| INT cdx6500frdtepNN1 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.17 | INTEGER | read-only | Full Status polling cycle. FRI port sends Full status enquiry messages to network every nN1 polls. |
| INT cdx6500frdtepNN2 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.18 | INTEGER | read-write | Error inactivity threshold. Number of errors during NN3 events that cause the station to be declared inactive. Should be less than or equal to nN3. |
| INT cdx6500frdtepNN3 | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.19 | INTEGER | read-only | Monitored events count for measuring nN3. nN2 errors during nN3 events will cause the station to be declared inactive. Should be greater than nN3. |
| INT cdx6500frdtepHighPriorityStn | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.20 | INTEGER | read-write | This parameter specifies a station who's PVC status has priority over all other stations when FRI same port back up is enabled. When the network reports this DLCI inactive, an alternate connection over a backup link is attempted. |
| INT cdx6500frdtepMaxVoiceBWBitsPerSec | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.21 | INTEGER | read-write | This parameter limits the bandwidth, in bits per sec (including overhead), for voice traffic passing through this frame relay port. A zero value disables any voice passing through this port. |
| INT cdx6500frdtepSegSizeVoicePresent | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.22 | INTEGER | read-write | Data packets to be segmented into this maximum frame size when voice is active on this port. segSize32 - 32 byte segments segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segments segSize512 - 512 byte segments segSize1024 - 1024 byte segments nc - Skipped during configuration. |
| INT cdx6500frdtepSegSizeVoiceNotPresent | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.23 | INTEGER | read-write | Data packets to be segmented into this maximum frame size when voice is not active on this port. segSize32 - 32 byte segments segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segments segSize512 - 512 byte segments segSize1024 - 1024 byte segments segSize2048 - 2048 byte segments segSize4096 - 4096 byte segments disable - segment size is 32768 bytes nc - Skipped during configuration. |
| INT cdx6500frdtepInvertTXClock | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.24 | INTEGER | read-write | This parameter specifies whether the phase of the transmit clock should be inverted. Note: This parameter is primarily for X.21 electrical interfaces. no - Don't invert. yes - Invert. |
| STR cdx6500frdtepControlProtocolOptions | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.25 | DisplayString | read-write | These options control the PVC management protocol none - No option selected async - The port will send/receive asynchronous A-bit if it is performing Network side protocol functionality nbit - The port will send and accept N-bit messages dbit - The port will send and accept D-bit messages This forces ASYNC to be specified (dbit+async) |
| INT cdx6500frdtepDiscardControlOptions | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.26 | INTEGER | read-write | This parameter controls the discard frame options none - No option selected debit - DE marked frames are discarded before non-DE frames |
| INT cdx6500frdtepElectricalInterfaceType | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.27 | INTEGER | read-write | Specify the Electrical Interface Type: V.24 - V.24 Electrical Interface Type V.35 - V.35 Electrical Interface Type V.36 - V.36 Electrical Interface Type X.21 - X.21 Electrical Interface Type NONE - Electrically disabled |
| INT cdx6500frdtepV24ElectricalInterfaceOption | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.28 | INTEGER | read-write | Specify the Pin 22 option: RI - V.24 uses Pin 22 for Ring Indicator output signal TM - V.24 uses Pin 22 for Test Mode input signal |
| INT cdx6500frdtepHighSpeedElectricalInterfaceOption | 1.3.6.1.4.1.449.2.1.2.1.1.5.1.29 | INTEGER | read-write | Specify the cable type: NONE - V.35/V.36/X.21 DCE with straight through cable XOVER - V.35/V.36/X.21 DCE with crossover adapter cable |
| cdx6500PCTStationProtocolGroup | 1.3.6.1.4.1.449.2.1.2.1.3 | |||
| cdx6500SPCTFRDTEStationTable | 1.3.6.1.4.1.449.2.1.2.1.3.2 | not-accessible | All of the configuration parameters relevant to the Frame Relay DTE Station table. | |
| cdx6500SPCTFRDTEStationEntry | 1.3.6.1.4.1.449.2.1.2.1.3.2.1 | not-accessible | A row of Frame Realy DTE station configuration parameters. | |
| INT cdx6500frdtesCfgPortNum | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.1 | INTEGER | read-only | FR DTE Port number. |
| INT cdx6500frdtesCfgDLCI | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.2 | INTEGER | read-write | The Data Link Connection Identifier (dlci) is the unique identifier for the station on the FRI Port. Its valid range is 16 - 1007. It must match the DLCI configured on the FR Networking Node. |
| INT cdx6500frdtesStationType | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.3 | INTEGER | read-write | Identifies the type of station being configured. annexG - This station uses X.25 signaling for layer 3 bypass - This station type bypasses layer 3. There is no signaling for SVC's on this station. voiceRelay - Not used in the current version. |
| INT cdx6500frdtesCommInfoRate | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.4 | INTEGER | read-write | This parameter (CIR) specifies the rate (in bits-per-second) that the Frame Relay network agrees to transfer information under congested conditions for the FRI Station. This value is used to throttle data on the FRI station for congestion control purposes. The CIR cannot be greater than the link speed. |
| INT cdx6500frdtesCommBurstSize | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.5 | INTEGER | read-write | This parameter (BC) specifies the maximum amount of data (in bits) that the Frame Relay network agrees to transfer over a time interval T = Committed Burst Size / Committed Information Rate. Must be > 1/20th of the Committed Information Rate. This is used for congestion control purposes. |
| INT cdx6500frdtesTransDelay | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.6 | INTEGER | read-write | This parameter is the expected one-way delay through the network. This is specified in milliseconds. |
| INT cdx6500frdtesControlledMode | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.7 | INTEGER | read-write | This parameter controls the method of congestion control: normal - congestion control is normal disable - never enter Congested State (CTRL) congested - never enter a Non-Congested State (UCTRL) limit - congestion control is normal but limits the data rate to no lower than CIR. nc - Skipped during configuration |
| INT cdx6500frdtesLinkAddress | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.8 | INTEGER | read-write | The logical link address must be set to complementary values in this FRI station and its corresponding remote FRI station: dte - station to have logical DTE address (A) dce - station to have logical DCE address (B) nc - Skipped during configuration. |
| INT cdx6500frdtesPVCChannels | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.9 | INTEGER | read-write | Number of logical channels used for Permanent Virtual Circuits. The total number of PVC and SVC channels on a station (logical link) should be kept as small as possible and consistent with needs. PVC connections must be configured in the PVC Table. |
| INT cdx6500frdtesStartingPVC | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.10 | INTEGER | read-write | This is the starting logical channel number for the Permanent Virtual Circuits on this FRI station. Not used if the number of PVCs = 0. |
| INT cdx6500frdtesSVCChannels | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.11 | INTEGER | read-write | Number of logical channels used in Switched Virtual Circuits. The total number of PVC and SVC channels on a station (logical link) should be kept as small as possible and consistent with needs. |
| INT cdx6500frdtesStartingSVC | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.12 | INTEGER | read-write | This is the starting logical channel number for the Switched Virtual Circuits on this station (logical link). Not used if the number of SVCs = 0. |
| INT cdx6500frdtesInitialFrame | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.13 | INTEGER | read-write | Specify the initial frame required by other end for (logical) link startup: none - do nothing (other end initiates link-up) sabm - send SABM disc - send DISC, then SABM nc - Skipped during configuration |
| INT cdx6500frdtesRetryTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.14 | INTEGER | read-write | T1 link retry timer value in tenths of a second (e.g. 30 = 3.0 seconds). |
| INT cdx6500frdtesPollTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.15 | INTEGER | read-write | This sets the time an idle link is probed for assurance of connection to the remote FRI station. 0 - disable the timer X - X is in tenths of a second (e.g. 40 = 4.0 seconds) and must be set greater than T1. |
| INT cdx6500frdtesTries | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.16 | INTEGER | read-write | The maximum number of attempts allowed to complete a transmission. |
| INT cdx6500frdtesFrameWinSize | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.17 | INTEGER | read-write | Frame level window size must be set to the same value at both this FRI station and the remote FRI station. |
| INT cdx6500frdtesPacketWinSize | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.18 | INTEGER | read-write | Packet level window size must be set to the same value at both this FRI station and the remote FRI station. |
| INT cdx6500frdtesMaxPacketSize | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.19 | INTEGER | read-write | This is the maximum X.25 packet size used on the station (logical link). For proper operation, this must be set to the same value at both this FRI station and the remote FRI station. nc - Skipped during configuration. |
| INT cdx6500frdtesUpperQueue | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.20 | INTEGER | read-write | This is the maximum number of data packets a channel on this station (logical link) will queue for transmission before invoking flow control to the attached channel |
| INT cdx6500frdtesLowerQueue | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.21 | INTEGER | read-write | This is the number of data packets a channel on this FRI station will have queued for transmission when it releases flow control to the attached channel |
| INT cdx6500frdtesRestartTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.22 | INTEGER | read-write | Restart-Request timeout timer in seconds. If timer expires on this FRI station, the Restart request is sent again. |
| INT cdx6500frdtesResetTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.23 | INTEGER | read-write | Reset-Request timeout timer in seconds. If timer expires on this FRI station, the Reset request is sent again. |
| INT cdx6500frdtesCallTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.24 | INTEGER | read-write | Call-Request timeout timer in seconds. If timer expires on this FRI station, the call is cleared. |
| INT cdx6500frdtesClearTimer | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.25 | INTEGER | read-write | Clear-Request timeout timer in seconds. If timer expires on this FRI station, the Clear request is sent again. |
| INT cdx6500frdtesX25Options | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.26 | INTEGER | read-only | Select X.25 options on this station (logical link) as follows: NONE - no option specified CUG - check closed user group; otherwise, CUG passes transparently CAUSE - pass cause, diagnostic, code in outbound packets HOLD - hold calls over link restart INL - inter-node link. Link goes to another 6500 device DELAY - Enable Delay and Path Trace on this link (link must be connected to Rel. 4.xx node) Any combination of above specified by summing (e.g. CUG+CAUSE+. . .). NOTE: Please use cdx6500frdtesStnX25Options, which has been added to replace this object. |
| STR cdx6500frdtesRCDestination | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.27 | DisplayString | read-write | All calls entering this station will be routed to the destination specified in this parameter, irrespective of route selection table entries. For example, to route all calls to X.25 port 3, use X25-3. To route calls to FRI port 2, station 4, use FRI-2S4. Blank this field to disable this function. |
| STR cdx6500frdtesCUG | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.28 | DisplayString | read-write | The station may be a member of up to 8 different Closed User Groups (CUGs). Each CUG membership must be a two digit number and separated by a comma. (e.g. 12,34,56,09,02,03 ). Two hyphens following each oher indicates no CUG Membership 00-99 - CUG Membership |
| INT cdx6500frdtesBillingRecords | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.29 | INTEGER | read-write | This controls whether billing (accounting) records will be created for calls on this FRI station. off - Billing records will not be created. on - Billing records will be created. nc - Skipped during configuration. |
| INT cdx6500frdtesCfgStationNum | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.30 | INTEGER | read-only | The number of the logical link on the line. This is the value of Sxx for routing purposes. |
| STR cdx6500frdtesStnX25Options | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.31 | DisplayString | read-write | Select X.25 options on this station (logical link) as follows: NONE - no option specified CUG - check closed user group; otherwise, CUG passes transparently CAUSE - pass cause, diagnostic, code in outbound packets HOLD - hold calls over link restart INL - inter-node link. Link goes to another 6500 device DELAY - Enable Delay and Path Trace on this link (link must be connected to Rel. 4.xx node) Any combination of above specified by summing (e.g. CUG+CAUSE+. . .). NOTE: This object has been added to replace cdx6500frdtesX25Options. |
| INT cdx6500frdtesStnFrameSegmenter | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.32 | INTEGER | read-write | Determine if this station will support the Frame Segmenter Header.The Frame Segmenter should be enabled if the frame relay port is configured to pass voice traffic. disabled - Frame Segmenter disabled. enabled - Frame Segmenter enabled. nc - Skipped during configuration. |
| INT cdx6500frdtesStnVoiceSVCChannels | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.33 | INTEGER | read-write | Number of logical voice channels used in Switched Virtual Circuits.The total number of voice and data channels on a station (logical link) should be kept as small as possible and consistent with needs. |
| INT cdx6500frdtesStnVoiceCongCtrlMode | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.34 | INTEGER | read-write | This parameter controls the method of voice congestion control: enabled - Station is forced into congestion when voice calls are detected. disabled - Station operates normally Use this parameter in voice applications, when the frame relay network can have more than 140ms of data buffered. One typical application is asymmetrical speeds. When this parameter is enabled, and voice is detected, delta T is forced to 50 ms and the BC is forced to 1/20 CIR. |
| INT cdx6500frdtesStnPeakUtilization | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.35 | INTEGER | read-write | The monitoring interval size specifies the time period to use when monitoring peak data link/CIR (Committed Information Rate) utilization. 0 - Disables this monitoring feature. 1 to 240 - The number of 64 second increments to use for the monitoring interval time period. For example: a value of 30 specifies a time duration equal to 30 * 64 seconds = 1920 seconds or 32 minutes. |
| INT cdx6500frdtesStnMaxInboundQueue | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.36 | INTEGER | read-write | This specifies the maximum number of frames from the network which may be queued in a BYPASS station. A smaller value may ve choosen for applications which experience objectable delays, if due to excessive growth of the BYPASS inbound queue. |
| INT cdx6500frdtesStnAnnexGRateReduction | 1.3.6.1.4.1.449.2.1.2.1.3.2.1.37 | INTEGER | read-write | This parameter determines whether Annex G stations will invoke implicit congestion control when a link error is detected, reducing their transmitted information rate to 1/4 CIR. The rate will be gradually increased in the normal way as non-BECN frames are received. |
| cdx6500Statistics | 1.3.6.1.4.1.449.2.1.3 | |||
| cdx6500StatProtocolGroup | 1.3.6.1.4.1.449.2.1.3.1 | |||
| cdx6500PSTPortProtocolGroup | 1.3.6.1.4.1.449.2.1.3.1.1 | |||
| cdx6500PPSTFRDTEPortTable | 1.3.6.1.4.1.449.2.1.3.1.1.5 | not-accessible | All of the statistics parameters relevant to the Frame Relay DTE Port table. | |
| cdx6500PPSTFRDTEPortEntry | 1.3.6.1.4.1.449.2.1.3.1.1.5.1 | not-accessible | A row of Frame Relay DTE Port statistics parameters. | |
| INT cdx6500frdtepStatsPortNum | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.1 | INTEGER | read-only | Specifies a specific port in the network diagram. |
| INT cdx6500frdtepPortStatus | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.2 | INTEGER | read-only | Specifies the current port status. disabled - Port has been disabled. enabled - Port is operational. busyOut - Port has been busied out. up - Port is operational. down - Port is down. na - Value not Available. |
| INT cdx6500frdtepPortSpeed | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.3 | INTEGER | read-only | Message transmition speed in bps. |
| INT cdx6500frdtepUtilizationIn | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.4 | INTEGER | read-only | Factor determined by comparison of volume (characters per second) of data and clock rate for a specific port. |
| INT cdx6500frdtepUtilizationOut | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.5 | INTEGER | read-only | Factor determined by comparison of volume (characters per second) of data and clock rate for a specific port. |
| CTR cdx6500frdtepCharInTotal | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.6 | Counter | read-only | Number of characters received since last boot or statistics reset. |
| CTR cdx6500frdtepCharOutTotal | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.7 | Counter | read-only | Number of characters transmitted since last boot or statistics reset. |
| INT cdx6500frdtepCharsInPerSec | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.8 | INTEGER | read-only | Average number of characters received per second. |
| INT cdx6500frdtepCharsOutPerSec | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.9 | INTEGER | read-only | Average number of characters transmitted per second. |
| CTR cdx6500frdtepFrameInTotal | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.10 | Counter | read-only | Number of frames received since last boot or statistics reset. |
| CTR cdx6500frdtepFrameOutTotal | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.11 | Counter | read-only | Number of frames transmitted since last boot or statistics reset. |
| INT cdx6500frdtepFramesInPerSec | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.12 | INTEGER | read-only | Average number of frames received per second. |
| INT cdx6500frdtepFramesOutPerSec | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.13 | INTEGER | read-only | Average number of frames transmitted per second. |
| NUM cdx6500frdtepOverrunErrors | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.14 | Counter16 | read-only | An input buffer overflowed and characters were discarded. |
| NUM cdx6500frdtepUnderrunErrors | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.15 | Counter16 | read-only | Number of errors detected since last node boot or reset of statistics. |
| NUM cdx6500frdtepCRCErrors | 1.3.6.1.4.1.449.2.1.3.1.1.5.1.16 | Counter16 | read-only | Number of errors detected by Cyclic Redundancy Check since last node boot reset of statistics. |
| cdx6500PSTStationProtocolGroup | 1.3.6.1.4.1.449.2.1.3.1.3 | |||
| cdx6500SPSTFRDTEStationTable | 1.3.6.1.4.1.449.2.1.3.1.3.2 | not-accessible | All of the statistics parameters relevant to the Frame Relay DTE Station (DLCI) table. | |
| cdx6500SPSTFRDTEStationEntry | 1.3.6.1.4.1.449.2.1.3.1.3.2.1 | not-accessible | A row of Frame Relay DTE station (DLCI) Statistics parameters. | |
| INT cdx6500frdtesStatsPortNum | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.1 | INTEGER | read-only | Specifies a specific port in the network diagram. |
| INT cdx6500frdtesStatsDLCI | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.2 | INTEGER | read-only | Data Link Connection Identifier is the unique identifier for the station on the FRI port and must match the DLCI configured on the Frame Relay networking node. |
| INT cdx6500frdtesUtilizationIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.3 | INTEGER | read-only | Indicates the quantity of user bytes sent down the link expressed as a percentage of the maximum number of bytes that could have been sent. |
| INT cdx6500frdtesUtilizationOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.4 | INTEGER | read-only | Indicates the quantity of user bytes sent down the link expressed as a percentage of the maximum number of bytes that could have been sent. |
| INT cdx6500frdtesMaxSVCCount | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.5 | INTEGER | read-only | Maximum number of SVCs available in the network. |
| INT cdx6500frdtesCurrentSVCCount | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.6 | INTEGER | read-only | Current number of SVCs currently in use. |
| CTR cdx6500frdtesCharInTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.7 | Counter | read-only | Number of characters received since last node boot or statistics reset. |
| CTR cdx6500frdtesCharOutTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.8 | Counter | read-only | Number of characters transmitted since last node boot or statistics reset. |
| INT cdx6500frdtesCharsInPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.9 | INTEGER | read-only | Average number of characters received per second. |
| INT cdx6500frdtesCharsOutPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.10 | INTEGER | read-only | Average number of characters transmitted per second. |
| CTR cdx6500frdtesPktInTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.11 | Counter | read-only | Number of packets received since last node boot or statistics reset. |
| CTR cdx6500frdtesPktOutTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.12 | Counter | read-only | Number of packets transmitted since last node boot or statistics reset. |
| INT cdx6500frdtesPktsInPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.13 | INTEGER | read-only | Average number of packets received per second. |
| INT cdx6500frdtesPktsOutPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.14 | INTEGER | read-only | Average number of packets transmitted per second. |
| INT cdx6500frdtesPacketsQueued | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.15 | INTEGER | read-only | Current number of packets buffered since last node boot or statistics reset. |
| CTR cdx6500frdtesFrameInTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.16 | Counter | read-only | Number of frames received since last node boot or statistics reset. |
| CTR cdx6500frdtesFrameOutTotal | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.17 | Counter | read-only | Number of frames transmitted since last node boot or statistics reset. |
| INT cdx6500frdtesFramesInPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.18 | INTEGER | read-only | Average number of frames received per second. |
| INT cdx6500frdtesFramesOutPerSec | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.19 | INTEGER | read-only | Average number of frames transmitted per second. |
| CTR cdx6500frdtesInfoFramesIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.20 | Counter | read-only | Data received since last node boot or statistics reset. |
| CTR cdx6500frdtesInfoFramesOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.21 | Counter | read-only | Data transmitted since last node boot or statistics reset. |
| CTR cdx6500frdtesRNRFramesIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.22 | Counter | read-only | Used by the DTE or the network to request that the data flow be stopped on a particular virtual circuit. |
| CTR cdx6500frdtesRNRFramesOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.23 | Counter | read-only | Used by the DTE or the network to request that the data flow be stopped on a particular virtual circuit. |
| CTR cdx6500frdtesRRFramesIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.24 | Counter | read-only | Used to clear the RNR request. |
| CTR cdx6500frdtesRRFramesOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.25 | Counter | read-only | Used to clear the RNR request. |
| CTR cdx6500frdtesREJFramesIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.26 | Counter | read-only | A REJ transmitted by a receiver requests retransmission of a frame, due to detection of a transmission or frame sequence error. |
| CTR cdx6500frdtesREJFramesOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.27 | Counter | read-only | A REJ transmitted by a receiver requests retransmission of a frame, due to detection of a transmission or frame sequence error. |
| CTR cdx6500frdtesDataPktsIn | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.28 | Counter | read-only | A packet containing user information. |
| CTR cdx6500frdtesDataPktsOut | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.29 | Counter | read-only | A packet containing user information. |
| INT cdx6500frdtesResetStats | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.30 | INTEGER | write-only | Resets the specified Frame Relay station statistics. reset - Reset station statistics. noReset - Do not reset station statistics. |
| INT cdx6500frdtesBoot | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.31 | INTEGER | write-only | Boots the specified Frame Relay station. boot - Boot station. noBoot - Do not boot station. |
| INT cdx6500frdtesDisable | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.32 | INTEGER | write-only | Disables the specified Frame Relay station. disable - Disable station. noDisable - Do not disable station. |
| INT cdx6500frdtesEnable | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.33 | INTEGER | write-only | Enables the specified Frame Relay station. enable - Enable station. noEnable - Do not enable station. |
| INT cdx6500frdtesStatsStationNumber | 1.3.6.1.4.1.449.2.1.3.1.3.2.1.34 | INTEGER | read-only | The number of the FRI Station. |
| cdx6500Controls | 1.3.6.1.4.1.449.2.1.4 |
RFC description
Manages Frame Relay DTE port configuration and statistics for Codex CDX6500 routers.
Start monitoring Codex CDX-6500 Frame Relay access device (DTE/customer-premises side) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.