DES-2108-MIB

All MIBs › DES-2108-MIB

Category: VLAN and Bridging, Vendor: D-Link

Description: Manages D-Link DES-2108 8-port smart switch L2 configuration, VLANs, and port settings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES-2108-MIB?

DES-2108-MIB is the vendor-specific SNMP management module for D-Link's DES-2108 8-port smart switch, part of D-Link's Layer 2 smart-switch product line aimed at small office/workgroup networks. It exposes configuration-oriented data covering Layer 2 switching parameters such as VLAN membership and port settings rather than deep performance counters or hardware sensors. No detailed object list was available in this batch, so its exact hardware/software status monitoring coverage cannot be enumerated, but a switch of this class would typically be polled alongside standard interface-level objects to confirm port link state and basic device uptime. It has no explicit stated dependency on other MIBs in the available source, though smart switches of this class commonly layer configuration on top of standard MIB-II interface definitions. Typical deployment is a small-office or workgroup network closet where a single low-cost 8-port switch needs basic VLAN/port configuration via SNMP rather than full CLI management, generally after a DES-2108-MIB download is loaded into the admin's MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES-2108-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-2108 8-port smart switch

Monitoring Examples

No object or table names were available in the source for this MIB, so a concrete polling scenario grounded in real OIDs cannot be constructed. Based on the short description, an admin would typically read VLAN membership and port-configuration settings specific to the DES-2108's proprietary MIB tree to confirm a port is assigned to the expected VLAN. This would usually be combined with standard IF-MIB interface counters to confirm the port is physically up. Exact table/object names are not available to cite here.

What Can Be Monitored

VLAN configuration
port settings
L2 switch administrative configuration

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
PhysAddress
mib-2

OIDs

OID symbolic	OID numeric	Type	Access	Description
d_link	1.3.6.1.4.1.171
dlink_products	1.3.6.1.4.1.171.10
dlink_DES21XXSeriesProd	1.3.6.1.4.1.171.10.61
des_2108	1.3.6.1.4.1.171.10.61.2
NTF swFiberInsert	1.3.6.1.4.1.171.10.61.2.0.1			Fiber insert trap
NTF swFiberRemove	1.3.6.1.4.1.171.10.61.2.0.2			Fiber remove trap
NTF swFiberAbnormalRXError	1.3.6.1.4.1.171.10.61.2.0.3			Fiber abnormal rx error trap
NTF swFiberAbnormalTXError	1.3.6.1.4.1.171.10.61.2.0.4			Fiber abnormal tx error trap
NTF swTPAbnormalRXError	1.3.6.1.4.1.171.10.61.2.0.5			Twisted Pair abnormal rx error trap
NTF swTPAbnormalTXError	1.3.6.1.4.1.171.10.61.2.0.6			Twisted Pair abnormal tx error trap
companyCommGroup	1.3.6.1.4.1.171.10.61.2.1
commSetTable	1.3.6.1.4.1.171.10.61.2.1.1		not-accessible	A list of SNMP Set Community Entries
commSetEntry	1.3.6.1.4.1.171.10.61.2.1.1.1		not-accessible	A list of SNMP Set Community properties
INT commSetIndex	1.3.6.1.4.1.171.10.61.2.1.1.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commSetName	1.3.6.1.4.1.171.10.61.2.1.1.1.2	DisplayString	read-write	The name of this SNMP Set Community Entry.
ROW commSetStatus	1.3.6.1.4.1.171.10.61.2.1.1.1.3	RowStatus	read-write	The RowStatus for the Set Community entry.
commGetTable	1.3.6.1.4.1.171.10.61.2.1.2		not-accessible	A list of SNMP Get Community Entries
commGetEntry	1.3.6.1.4.1.171.10.61.2.1.2.1		not-accessible	A list of SNMP Get Community properties
INT commGetIndex	1.3.6.1.4.1.171.10.61.2.1.2.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commGetName	1.3.6.1.4.1.171.10.61.2.1.2.1.2	DisplayString	read-write	The name of this SNMP Get Community Entry.
ROW commGetStatus	1.3.6.1.4.1.171.10.61.2.1.2.1.3	RowStatus	read-write	The RowStatus for the Get Community entry.
commTrapTable	1.3.6.1.4.1.171.10.61.2.1.3		not-accessible	A list of SNMP Trap Community Entries
commTrapEntry	1.3.6.1.4.1.171.10.61.2.1.3.1		not-accessible	A list of SNMP Trap Community properties
INT commTrapIndex	1.3.6.1.4.1.171.10.61.2.1.3.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commTrapName	1.3.6.1.4.1.171.10.61.2.1.3.1.2	DisplayString	read-write	The name of this SNMP Trap Community Entry.
IP commTrapIpAddress	1.3.6.1.4.1.171.10.61.2.1.3.1.3	IpAddress	read-write	The IP Address of this SNMP Trap Community Entry.
INT commTrapVlanId	1.3.6.1.4.1.171.10.61.2.1.3.1.4	INTEGER	read-write	The Trap VLAN identifier of this SNMP Trap Community Entry. The value must be from 1 to 4094.
INT commTrapSNMPBootup	1.3.6.1.4.1.171.10.61.2.1.3.1.5	INTEGER	read-write	Bootup trap
INT commTrapSNMPTPLinkUpDown	1.3.6.1.4.1.171.10.61.2.1.3.1.6	INTEGER	read-write	Twisted Pair link up / link down trap
INT commTrapSNMPFiberLinkUpDown	1.3.6.1.4.1.171.10.61.2.1.3.1.7	INTEGER	read-write	Fiber link up / link down trap
INT commTrapTrapAbnormalTPRXError	1.3.6.1.4.1.171.10.61.2.1.3.1.9	INTEGER	read-write	Twisted Pair abnormal receive error trap
INT commTrapTrapAbnormalTPTXError	1.3.6.1.4.1.171.10.61.2.1.3.1.10	INTEGER	read-write	Twisted Pair abnormal transmit error trap
INT commTrapTrapAbnormalFiberRXError	1.3.6.1.4.1.171.10.61.2.1.3.1.11	INTEGER	read-write	Fiber abnormal receive error trap
INT commTrapTrapAbnormalFiberTXError	1.3.6.1.4.1.171.10.61.2.1.3.1.12	INTEGER	read-write	Fiber abnormal transmit error trap
ROW commTrapStatus	1.3.6.1.4.1.171.10.61.2.1.3.1.13	RowStatus	read-write	The RowStatus for the Trap Community entry.
companyMiscGroup	1.3.6.1.4.1.171.10.61.2.3
INT miscReset	1.3.6.1.4.1.171.10.61.2.3.2	INTEGER	read-write	Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.
INT miscStatisticsReset	1.3.6.1.4.1.171.10.61.2.3.3	INTEGER	read-write	Resets the units statistics. A (1) resets the unit, a (2) does nothing.
companySpanGroup	1.3.6.1.4.1.171.10.61.2.4
INT spanOnOff	1.3.6.1.4.1.171.10.61.2.4.1	INTEGER	read-write	Enable/Disable Spanning Tree. A (1) enables, a (2) disables.
companyConfigGroup	1.3.6.1.4.1.171.10.61.2.11
STR configVerSwPrimary	1.3.6.1.4.1.171.10.61.2.11.1	DisplayString	read-only	The software image version string
STR configVerHwChipSet	1.3.6.1.4.1.171.10.61.2.11.2	DisplayString	read-only	The hardware chipset version string
configPortTable	1.3.6.1.4.1.171.10.61.2.11.6		not-accessible	A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces.
configPortEntry	1.3.6.1.4.1.171.10.61.2.11.6.1		not-accessible	An enterprise specific interface entry.
INT configPort	1.3.6.1.4.1.171.10.61.2.11.6.1.1	INTEGER	read-only	A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber.
INT configPortSpeed	1.3.6.1.4.1.171.10.61.2.11.6.1.2	INTEGER	read-write	The port's speed desired state.
INT configPortOperStatus	1.3.6.1.4.1.171.10.61.2.11.6.1.3	INTEGER	read-only	The port's operating speed state.
INT configPortFlowControl	1.3.6.1.4.1.171.10.61.2.11.6.1.4	INTEGER	read-write	The port will avoid transmitting a new packet for the period of time specified in a received PAUSE packet when enabled.
INT configPortFlowControlOper	1.3.6.1.4.1.171.10.61.2.11.6.1.5	INTEGER	read-only	The port's operating flow control state.
INT configPortPriority	1.3.6.1.4.1.171.10.61.2.11.6.1.6	INTEGER	read-write	The port's current priority.
INT configVLANMode	1.3.6.1.4.1.171.10.61.2.11.7	INTEGER	read-write	Determines the VLAN mode.
configMirrorTable	1.3.6.1.4.1.171.10.61.2.11.8		not-accessible	A list of the Mirror
configMirrorEntry	1.3.6.1.4.1.171.10.61.2.11.8.1		not-accessible	A Mirror entry containing the Mirror id and mode
INT configMirrorId	1.3.6.1.4.1.171.10.61.2.11.8.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported.
INT configMirrorMode	1.3.6.1.4.1.171.10.61.2.11.8.1.2	INTEGER	read-write	When deciding the mirroring source port, then Mirror mode will be available.
INT configMirrorMon	1.3.6.1.4.1.171.10.61.2.11.8.1.3	INTEGER	read-write	When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled.
POR configMirrorSrc	1.3.6.1.4.1.171.10.61.2.11.8.1.4	PortList	read-write	When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring source port. This value has a valid range of 1 to ifNumber when enbaled. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
ROW configMirrorStatus	1.3.6.1.4.1.171.10.61.2.11.8.1.5	RowStatus	read-write	The RowStatus for the Mirror entry.
INT configSNMPEnable	1.3.6.1.4.1.171.10.61.2.11.9	INTEGER	read-write	Enable/Disable SNMP function. A (1) enables, a (2) disables.
INT configIpAssignmentMode	1.3.6.1.4.1.171.10.61.2.11.12	INTEGER	read-write	Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP).
MAC configPhysAddress	1.3.6.1.4.1.171.10.61.2.11.13	MacAddress	read-only	The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station.
STR configPasswordAdmin	1.3.6.1.4.1.171.10.61.2.11.15	DisplayString	write-only	The adminstrator password
IP configIpAddress	1.3.6.1.4.1.171.10.61.2.11.16	IpAddress	read-write	The IP Address for the RDU box.
IP configNetMask	1.3.6.1.4.1.171.10.61.2.11.17	IpAddress	read-write	The network mask for the RDU box.
IP configGateway	1.3.6.1.4.1.171.10.61.2.11.18	IpAddress	read-write	The Gatway Address for the unit.
INT configSave	1.3.6.1.4.1.171.10.61.2.11.19	INTEGER	read-write	Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing.
INT configRestoreDefaults	1.3.6.1.4.1.171.10.61.2.11.22	INTEGER	read-write	Restores the configuration of the unit to the original settings.
companyPVlanGroup	1.3.6.1.4.1.171.10.61.2.12
pvlanTable	1.3.6.1.4.1.171.10.61.2.12.1		not-accessible	A list of the Port-based VLANs
pvlanEntry	1.3.6.1.4.1.171.10.61.2.12.1.1		not-accessible	A Port-based VLAN entry containing the id and name.
INT pvlanId	1.3.6.1.4.1.171.10.61.2.12.1.1.1	INTEGER	read-only	The VLAN identifier. A maximum of 28 VLANs is supported. The value must be from 1 to 28
STR pvlanName	1.3.6.1.4.1.171.10.61.2.12.1.1.2	DisplayString	read-write	The VLAN name associated with the Id.
POR pvlanMember	1.3.6.1.4.1.171.10.61.2.12.1.1.3	PortList	read-write	The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
INT pvlanStatus	1.3.6.1.4.1.171.10.61.2.12.1.1.5	INTEGER	read-write	The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
companyTVlanGroup	1.3.6.1.4.1.171.10.61.2.13
tvlanTable	1.3.6.1.4.1.171.10.61.2.13.1		not-accessible	A list of the VLANs
tvlanEntry	1.3.6.1.4.1.171.10.61.2.13.1.1		not-accessible	A VLAN entry containing the VLAN id and name.
INT tvlanId	1.3.6.1.4.1.171.10.61.2.13.1.1.1	INTEGER	read-only	The VLAN identifier. A maximum of 64 VLANs is supported. The value must be from 1 to 4094.
POR tvlanMember	1.3.6.1.4.1.171.10.61.2.13.1.1.3	PortList	read-write	The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
POR tvlanUntaggedPorts	1.3.6.1.4.1.171.10.61.2.13.1.1.4	PortList	read-write	If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged.
INT tvlanStatus	1.3.6.1.4.1.171.10.61.2.13.1.1.5	INTEGER	read-write	The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
tvlanPortTable	1.3.6.1.4.1.171.10.61.2.13.2		not-accessible	A list of ports and their associated VLAN.
tvlanPortEntry	1.3.6.1.4.1.171.10.61.2.13.2.1		not-accessible	Information pertaining to an individual port regarding to which VLAN it belongs.
INT tvlanPortPortId	1.3.6.1.4.1.171.10.61.2.13.2.1.1	INTEGER	read-only	A port identifier that is in the range of 1 to ifNumber.
INT tvlanPortVlanId	1.3.6.1.4.1.171.10.61.2.13.2.1.2	INTEGER	read-write	The default VLAN identifier.
INT tvlanPortPriority	1.3.6.1.4.1.171.10.61.2.13.2.1.3	INTEGER	read-write	The default priority.
INT tvlanManagement	1.3.6.1.4.1.171.10.61.2.13.3	INTEGER	read-write	The management vlan which allow to forwarding to cpu.
companyStaticGroup	1.3.6.1.4.1.171.10.61.2.21
INT staticOnOff	1.3.6.1.4.1.171.10.61.2.21.1	INTEGER	read-write	Enable/Disable Static MAC. A (1) enables, a (2) disables.
POR staticAutoLearning	1.3.6.1.4.1.171.10.61.2.21.2	PortList	read-write	The set of the device's member ports that belong to the Static MAC auto learning enable/disable. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is in auto learning enable state; the port is not in auto learning state if its bit has a value of '0'.
staticTable	1.3.6.1.4.1.171.10.61.2.21.3		not-accessible	A list of the Static MACs
staticEntry	1.3.6.1.4.1.171.10.61.2.21.3.1		not-accessible	A Static MAC entry containing the mac and forwarding port.
INT staticId	1.3.6.1.4.1.171.10.61.2.21.3.1.1	INTEGER	read-only	The Static MAC identifier. A maximum of 60 Static MACs is supported. The value must be from 1 to 60
STR staticMac	1.3.6.1.4.1.171.10.61.2.21.3.1.2	DisplayString	read-write	The Static MAC associated with the Id.
INT staticPort	1.3.6.1.4.1.171.10.61.2.21.3.1.3	INTEGER	read-write	The Static MAC forwarding port with the ID.
INT staticVlanID	1.3.6.1.4.1.171.10.61.2.21.3.1.4	INTEGER	read-write	The Static MAC VLAN ID with the ID.
INT staticStatus	1.3.6.1.4.1.171.10.61.2.21.3.1.5	INTEGER	read-write	The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
companyIgsGroup	1.3.6.1.4.1.171.10.61.2.22
igsSystem	1.3.6.1.4.1.171.10.61.2.22.1
INT igsStatus	1.3.6.1.4.1.171.10.61.2.22.1.2	INTEGER	read-write	Enables or disables IGMP snooping in the system
INT igsRouterPortPurgeInterval	1.3.6.1.4.1.171.10.61.2.22.1.4	INTEGER	read-write	This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, a 'RouterPortPurgeTimer' runs for 'RouterPortPurgeInterval'. This timer will be restarted whenever a router control message is received over that port. If no router control mssages are received for 'RouterPortPurgeInterval' time, the learnt router port entry will be purged
INT igsHostPortPurgeInterval	1.3.6.1.4.1.171.10.61.2.22.1.5	INTEGER	read-write	This is the interval (in seconds) after which a learnt host port entry will be purged. For each host port learnt, a 'PortPurgeTimer' runs for 'HostPortPurgeInterval'. This timer will be restarted whenever a report message from host is received over that port. If no report mssages are received for 'HostPortPurgeInterval' time, the learnt host entry will be purged from the multicast group
igsBrg	1.3.6.1.4.1.171.10.61.2.22.2
POR igsBrgRouterPortList	1.3.6.1.4.1.171.10.61.2.22.2.1	PortList	read-write	Contains list of bridge ports through which a router is reachable. These router ports can be learnt through control messages received from routers, and statically configured
igsBrgMcastFwdTable	1.3.6.1.4.1.171.10.61.2.22.2.2		not-accessible	This table contains multicast forwarding information learnt when VLAN is DISABLED in the system.
igsBrgMcastFwdEntry	1.3.6.1.4.1.171.10.61.2.22.2.2.1		not-accessible	This table contains multicast group address and the list of ports who have members for the multicast group.
MAC igsBrgMcastFwdGroupAddress	1.3.6.1.4.1.171.10.61.2.22.2.2.1.1	MacAddress	not-accessible	MAC multicast group address.
POR igsBrgMcastFwdPortListMac	1.3.6.1.4.1.171.10.61.2.22.2.2.1.2	PortList	read-only	List of ports who have members for the MAC multicast group.
companyStormCtrlGroup	1.3.6.1.4.1.171.10.61.2.23
INT stormctrlOnOff	1.3.6.1.4.1.171.10.61.2.23.1	INTEGER	read-write	Enable/Disable ARP STORM CONTROL. A (1) enables, a (2) disables.
INT stormctrlStatus	1.3.6.1.4.1.171.10.61.2.23.2	INTEGER	read-write	Unlock ARP STORM CONTROL mechanism. A (1) locked, a (2) unlock.

RFC description

D-Link DES-2108 managed switch with community, host, and spanning tree configuration support.

Start monitoring D-Link DES-2108 8-port smart switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES-2108-MIB

What Is DES-2108-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description