All MIBs › DGS3000-24TC-L3MGMT-MIB
Last Updated: 2012-05-23
Category: Technology: Routing/L3, Vendor: D-Link
Description: L3 management MIB for D-Link DGS-3000-24TC switch covering routing, OSPF, and Layer 3 management features.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DGS3000-24TC-L3MGMT-MIB?
This proprietary D-Link MIB defines Layer 3 network management information for the DGS-3000-24TC, a 24-port Layer 3 switch, covering routing-protocol configuration including DVMRP multicast routing and OSPF, plus general L3 management such as route preference. Like its DGS-3000-10TC sibling, it exposes routing-plane configuration and operational-status data rather than basic interface counters. Its monitoring value comes from surfacing routing-protocol health at the software level: DVMRP neighbor timeout and bad-packet/bad-route counters flag multicast-routing problems, while OSPF ECMP objects reveal load-balancing configuration, complementing simple interface up/down status with actual routing-behavior visibility. It complements standard routing MIBs such as OSPF-MIB and DVMRP conventions, layering D-Link-specific extensions on top. It is deployed on DGS-3000-24TC switches in routed campus environments needing multicast and OSPF routing across VLANs. Engineers can download the DGS3000-24TC-L3MGMT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DGS3000-24TC-L3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link DGS-3000-24TC Layer 3 switch
Monitoring Examples
An administrator would poll swL3dvmrpInterfaceTable entries such as swL3dvmrpInterfaceLocalAddress, swL3dvmrpInterfaceProbe, and swL3dvmrpInterfaceNbrTimeout to confirm DVMRP neighbor relationships remain established, and watch swL3dvmrpInterfaceRcvBadPkts/swL3dvmrpInterfaceRcvBadRoutes for a rising count that would indicate a misbehaving multicast peer. Checking swL3OspfECMPCrcHigh and swL3OspfECMPTCPorUDPport alongside swL3RoutePreference would reveal whether OSPF ECMP load balancing and routing preference are functioning as configured.
What Can Be Monitored
- DVMRP interface status and metrics
- DVMRP bad packet/route counters
- OSPF ECMP configuration
- route preference settings
- L3 routing interface status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex |
From OSPF-MIB
| AreaID | |
| DesignatedRouterPriority | |
| HelloRange | |
| Metric | |
| PositiveInteger | |
| RouterID | |
| Status | |
| TOSType | |
| UpToMaxAge |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| PhysAddress | |
| RowStatus | |
| TimeStamp | |
| TruthValue |
| dgs3000-24-tcax |
How to Use in IPNetwork Monitor
Example using swL3ospfVirtIfEvents OID:
Select a D-Link DGS-3000-24TC Layer 3 switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL3ospfVirtIfEvents into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of state changes or error events on this Virtual Link. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| swL3MgmtMIB | 1.3.6.1.4.1.171.11.133.4.1.3 | The Structure of Layer 3 Network Management Information for the proprietary enterprise. | ||
| swL3DevMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.1 | |||
| swL3DevCtrl | 1.3.6.1.4.1.171.11.133.4.1.3.1.1 | |||
| INT swL3DevCtrlRIPState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.1 | INTEGER | read-write | This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled. |
| INT swL3DevCtrlOSPFState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.2 | INTEGER | read-write | This object indicates OSPF protocol is enabled or disabled. |
| INT swL3DevCtrlDVMRPState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.3 | INTEGER | read-write | This object indicates DVMRP protocol is enabled or disabled. |
| INT swL3DevCtrlVRRPState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.5 | INTEGER | read-write | This object indicates VRRP protocol is enabled or disabled. |
| INT swL3DevCtrlVrrpPingState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.6 | INTEGER | read-write | This object indicates VRRP protocol Ping is enabled or disabled. |
| INT swL3DevCtrlDHCPAutoConfigState | 1.3.6.1.4.1.171.11.133.4.1.3.1.1.7 | INTEGER | read-write | This object indicates auto config is enabled or disabled. |
| swL3IpMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.2 | |||
| swL3IpCtrlMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.2.1 | |||
| swL3IpCtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3 | not-accessible | This table contains IP interface information. | |
| swL3IpCtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1 | not-accessible | A list of information about a specific IP interface. | |
| STR swL3IpCtrlInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| INT swL3IpCtrlIfIndex | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.2 | INTEGER | read-only | This object uniquely identifies the IP interface number in the swL3IpCtrlTable. |
| IP swL3IpCtrlIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.3 | IpAddress | read-write | The IP address of the interface. This object only can take the value of the unicast IP address. |
| IP swL3IpCtrlIpSubnetMask | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.4 | IpAddress | read-write | The IP net mask for this interface. |
| STR swL3IpCtrlVlanName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.5 | DisplayString | read-write | This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table. |
| INT swL3IpCtrlProxyArp | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.6 | INTEGER | read-create | This object indicates enable/disable of the proxy ARP function for IPv4. |
| T/F swL3IpCtrlSecondary | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.7 | TruthValue | read-create | When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP. |
| INT swL3IpCtrlMode | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.8 | INTEGER | read-write | This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server. |
| INT swL3IpCtrlAdminState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.9 | INTEGER | read-write | The state of the IP interface. |
| INT swL3IpCtrlIpv4AdminState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.10 | INTEGER | read-write | The IPv4 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled. |
| INT swL3IpCtrlIpv6AdminState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.12 | INTEGER | read-write | The IPv6 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled. |
| ADR swL3IpCtrlIpv6LinkLocalAddress | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.14 | Ipv6Address | read-only | The IPv6 link local address for this interface. |
| INT swL3IpCtrlIpv6LinkLocalPrefixLen | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.15 | INTEGER | read-only | The IPv6 prefix length for this IPv6 link local address. |
| ROW swL3IpCtrlState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.16 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| INT swL3IpCtrlIpv6LinkLocalAutoState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.17 | INTEGER | read-write | The state of the IPv6 link local auto. |
| INT swL3IpCtrlLocalProxyArp | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.18 | INTEGER | read-create | This object indicates enable/disable of the local proxy ARP function for IPv4. |
| INT swL3IpCtrlDhcpv6ClientState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.20 | INTEGER | read-write | The object indicates the state of the DHCPv6 client. |
| INT swL3IpCtrlIpDirectedBroadcastState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.21 | INTEGER | read-write | The object indicates the state of the IP Directed Broadcast. |
| INT swL3IpCtrlIpDhcpOption12State | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.22 | INTEGER | read-write | Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message. |
| STR swL3IpCtrlIpDhcpOption12HostName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.3.1.23 | DisplayString | read-write | Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12. |
| swL3Ipv6CtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4 | not-accessible | This table contains IPv6 information of an IP interface. | |
| swL3Ipv6CtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1 | not-accessible | A list of IPv6 information about a specific IP interface. | |
| STR swL3Ipv6CtrlInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| INT swL3Ipv6CtrlMaxReassmblySize | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.2 | INTEGER | read-only | Maximum Reassembly Size of the IP interface. |
| U32 swL3Ipv6CtrlNsRetransTimer | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.3 | Unsigned32 | read-write | Neighbor solicitation's retransmit timer. The unit is set in milliseconds. |
| INT swL3Ipv6CtrlRaState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.5 | INTEGER | read-write | Neighbor solicited state. |
| INT swL3Ipv6CtrlRaMinRtrAdvInterval | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.6 | INTEGER | read-write | The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval |
| INT swL3Ipv6CtrlRaMaxRtrAdvInterval | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.7 | INTEGER | read-write | The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. |
| INT swL3Ipv6CtrlRaLifeTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.8 | INTEGER | read-write | Indicates the lifetime of the router as the default router. |
| INT swL3Ipv6CtrlRaReachableTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.9 | INTEGER | read-write | Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation. |
| U32 swL3Ipv6CtrlRaRetransTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.10 | Unsigned32 | read-write | Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond. |
| INT swL3Ipv6CtrlRaHopLimit | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.11 | INTEGER | read-write | Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message. |
| INT swL3Ipv6CtrlRaManagedFlag | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.12 | INTEGER | read-write | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration. |
| INT swL3Ipv6CtrlRaOtherConfigFlag | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.4.1.13 | INTEGER | read-write | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information. |
| swL3Ipv6AddressCtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5 | not-accessible | This table contains IPv6 address information for each IP interface. | |
| swL3Ipv6AddressCtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1 | not-accessible | A list of information about a specific IPv6 address. | |
| STR swL3Ipv6AddressCtrlInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| ADR swL3Ipv6Address | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.2 | Ipv6Address | read-only | Specify the IPv6 address. |
| INT swL3Ipv6AddressCtrlPrefixLen | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.3 | INTEGER | read-only | Indicates the prefix length of this IPv6 address. |
| U32 swL3Ipv6AddressCtrlPreferredLifeTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.4 | Unsigned32 | read-write | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff. |
| U32 swL3Ipv6AddressCtrlValidLifeTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.5 | Unsigned32 | read-write | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff. |
| INT swL3Ipv6AddressCtrlOnLinkFlag | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.6 | INTEGER | read-write | When enabled, the address implied by the specified prefix is available on the link where the RA message is received. |
| INT swL3Ipv6AddressCtrlAutonomousFlag | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.7 | INTEGER | read-write | When enabled, the specified prefix will be used to create an autonomous address configuration. |
| ROW swL3Ipv6AddressCtrlState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.8 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| INT swL3Ipv6AddressCtrlAddressType | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.5.1.9 | INTEGER | read-only | This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement. |
| INT swL3IpCtrlAllIpIfState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.7 | INTEGER | read-write | This object indicates all interface function state of the device. (except the loopback interface) |
| swL3LoopBackIpCtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8 | not-accessible | This table contains loopback IP interface information. | |
| swL3LoopBackIpCtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1 | not-accessible | A list of information about a specific loopback IP interface. | |
| STR swL3LoopBackIpCtrlInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.1 | DisplayString | read-only | This object indicates the name of the loopback IP interface. |
| INT swL3LoopBackIpCtrlIfIndex | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.2 | INTEGER | read-only | This object uniquely identifies the loopback IP interface number in the swL3LoopBackIpCtrlTable. |
| IP swL3LoopBackIpCtrlIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.3 | IpAddress | read-create | The IP address of the loopback interface. This object only can take the value of the unicast IP address. |
| IP swL3LoopBackIpCtrlIpSubnetMask | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.4 | IpAddress | read-create | The IP net mask for this loopback interface. |
| INT swL3LoopBackIpCtrlAdminState | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.5 | INTEGER | read-create | The state of the loopback IP interface. |
| ROW swL3LoopBackIpCtrlRowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.2.1.8.1.6 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| swL3IpFdbMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.2.2 | |||
| swL3IpFdbInfoTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1 | not-accessible | A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets. | |
| swL3IpFdbInfoEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1.1 | not-accessible | Information about a specific IP address for which the bridge has some forwarding and/or filtering information. | |
| IP swL3IpFdbInfoIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1.1.1 | IpAddress | read-only | A IP address for which switch has forwarding and/or filtering information. |
| IP swL3IpFdbInfoIpSubnetMask | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1.1.2 | IpAddress | read-only | A IP net mask for this interface for which the switch has forwarding and/or filtering information. |
| INT swL3IpFdbInfoPort | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1.1.3 | INTEGER | read-only | Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address. |
| INT swL3IpFdbInfoType | 1.3.6.1.4.1.171.11.133.4.1.3.2.2.1.1.4 | INTEGER | read-only | The status of this entry. |
| INT swL3IpArpAgingTime | 1.3.6.1.4.1.171.11.133.4.1.3.2.4 | INTEGER | read-write | The timeout period in minutes for aging out dynamically learned ARP information. |
| swL3IpStaticRouteTable | 1.3.6.1.4.1.171.11.133.4.1.3.2.5 | not-accessible | This entity's IP static Routing table. | |
| swL3IpStaticRouteEntry | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1 | not-accessible | A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and delete actions. | |
| IP swL3IpStaticRouteDest | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.1 | IpAddress | read-only | The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x. |
| IP swL3IpStaticRouteMask | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.2 | IpAddress | read-only | Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest. |
| INT swL3IpStaticRouteBkupState | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.3 | INTEGER | read-create | The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3). |
| IP swL3IpStaticRouteNextHop | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.4 | IpAddress | read-only | Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop. |
| INT swL3IpStaticRouteMetric | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.5 | INTEGER | read-create | Specifies the routing metric for this route. |
| INT swL3IpStaticRouteStatus | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.6 | INTEGER | read-create | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table. |
| INT swL3IpStaticRouteWeight | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.7 | INTEGER | read-create | Specifies the weight value. Used for the weighted multipath. |
| STR swL3IpStaticRouteInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.8 | DisplayString | read-only | Specifies the name of the IP interface. |
| INT swL3IpStaticRouteCost | 1.3.6.1.4.1.171.11.133.4.1.3.2.5.1.9 | INTEGER | read-only | Specifies the cost of the Route Entry. |
| swL3RelayMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.3 | |||
| swL3RelayDhcpMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.3.1 | |||
| INT swL3RelayDhcpState | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.1 | INTEGER | read-write | This object indicates if the DHCP Relay function is enabled or disabled. |
| INT swL3RelayDhcpHopCount | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.2 | INTEGER | read-write | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| INT swL3RelayDhcpTimeThreshold | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.3 | INTEGER | read-write | This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet. |
| swL3RelayDhcpCtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.4 | not-accessible | This table specifies the IP address as a destination to forward (relay) DHCP packets to. | |
| swL3RelayDhcpCtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.4.1 | not-accessible | A list of information specifying the IP address as a destination to forward (relay) DHCP packets to. | |
| STR swL3RelayDhcpCtrlInterfaceName | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.4.1.1 | DisplayString | read-only | The name of the IP interface. |
| IP swL3RelayDhcpCtrlServer | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.4.1.2 | IpAddress | read-only | The DHCP server IP address. |
| INT swL3RelayDhcpCtrlState | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.4.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| INT swL3RelayDhcpOption82State | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.5 | INTEGER | read-write | This object indicates DHCP Relay Option 82 function is enabled or disabled. |
| INT swL3RelayDhcpOption82CheckState | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.6 | INTEGER | read-write | This object indicates DHCP Relay Option 82 Check function is enabled or disabled. |
| INT swL3RelayDhcpOption82Policy | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.7 | INTEGER | read-write | This object indicates DHCP Relay Option 82 Policy. |
| swL3DHCPRelayOption60 | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8 | |||
| INT swL3DHCPRelayOption60State | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.1 | INTEGER | read-write | This object indicates DHCP relay option 60 function is enabled or disabled. |
| INT swL3DHCPRelayOption60DefMode | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.2 | INTEGER | read-write | This object indicates default mode that has no option 60 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption60DefRelayIp. drop(2): means to drop the packet. |
| swL3DHCPRelayOption60DefTable | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.3 | not-accessible | This table indicates the default relay servers for the packet that has no option 60 mathcing rules. | |
| swL3DHCPRelayOption60DefEntry | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.3.1 | not-accessible | A list of information indicates the default relay servers for the packet that has no option 60 mathcing rules. | |
| IP swL3DHCPRelayOption60DefRelayIp | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.3.1.1 | IpAddress | read-only | This object indicates the IP address of default relay server. |
| ROW swL3DHCPRelayOption60DefRowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.3.1.2 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3DHCPRelayOption60Table | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4 | not-accessible | This table indicates the relay servers for the packet at option 60 rules. | |
| swL3DHCPRelayOption60Entry | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4.1 | not-accessible | A list of information indicates the relay servers for the packet at option 60 rules. | |
| STR swL3DHCPRelayOption60String | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4.1.1 | DisplayString | read-only | This object indicates string of this entry. |
| IP swL3DHCPRelayOption60RelayIp | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4.1.2 | IpAddress | read-only | This object indicates the IP address of relay server. |
| INT swL3DHCPRelayOption60MatchType | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4.1.3 | INTEGER | read-create | This object indicates match state of this entry. exact(1): means the option 60 string in the packet must full match with the specified string. partial(2): means the option 60 string in the packet only need partial match with the specified string. |
| ROW swL3DHCPRelayOption60RowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.8.4.1.4 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3DHCPRelayOption61 | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9 | |||
| INT swL3DHCPRelayOption61State | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.1 | INTEGER | read-write | This object indicates DHCP relay option 61 function is enabled or disabled. |
| INT swL3DHCPRelayOption61DefMode | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.2 | INTEGER | read-write | This object indicates default mode that has no option 61 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61DefRelayIp. drop(2): means to drop the packet. |
| IP swL3DHCPRelayOption61DefRelayIp | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.3 | IpAddress | read-write | This object indicates the IP address of default relay server that has no option 61 mathcing rules. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'. |
| swL3DHCPRelayOption61Table | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4 | not-accessible | This table indicates the relay servers for the packet at option 61 rules. | |
| swL3DHCPRelayOption61Entry | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1 | not-accessible | A list of information indicates the relay servers for the packet at option 61 rules. | |
| INT swL3DHCPRelayOption61ClientType | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1.1 | INTEGER | read-only | This object indicates client type of this entry. mac(1): means the client-ID which is the MAC address of client. string(2): means the client-ID which is specified string by administrator. |
| STR swL3DHCPRelayOption61ClientID | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1.2 | DisplayString | read-only | This object indicates string of this entry. When swL3DHCPRelayOption61ClientType is mac(1), the format of this object should be XX-XX-XX-XX-XX-XX (MAC address). |
| INT swL3DHCPRelayOption61Mode | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1.3 | INTEGER | read-create | This object indicates mode of this entry. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61RelayIp. drop(2): means to drop the packet. |
| IP swL3DHCPRelayOption61RelayIp | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1.4 | IpAddress | read-create | This object indicates the IP address of relay server. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'. |
| ROW swL3DHCPRelayOption61RowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.3.1.9.4.1.5 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3RelayDnsMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.3.2 | |||
| INT swL3RelayDnsState | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.1 | INTEGER | read-write | This object indicates if the DNS Relay function is enabled or disabled. |
| IP swL3RelayDnsPrimaryServer | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.2 | IpAddress | read-write | This object indicates the address of the primary DNS server. |
| IP swL3RelayDnsSecondaryServer | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.3 | IpAddress | read-write | This object indicates the address of the secondary DNS server. |
| INT swL3RelayDnsCacheState | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.4 | INTEGER | read-write | This object indicates DNS Relay cache is enabled or disabled. |
| INT swL3RelayDnsStaticTableState | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.5 | INTEGER | read-write | This object indicates DNS Relay static table is enabled or disabled. |
| swL3RelayDnsCtrlTable | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.6 | not-accessible | This table displays the current DNS relay static table. | |
| swL3RelayDnsCtrlEntry | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.6.1 | not-accessible | A list of information display the current DNS relay static table. | |
| STR swL3RelayDnsCtrlDomainName | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.6.1.1 | DisplayString | read-only | The domain name of the entry. |
| IP swL3RelayDnsCtrlIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.6.1.2 | IpAddress | read-only | The IP address of the entry. |
| INT swL3RelayDnsCtrlState | 1.3.6.1.4.1.171.11.133.4.1.3.3.2.6.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3Md5Table | 1.3.6.1.4.1.171.11.133.4.1.3.4 | not-accessible | This table displays the current MD5 key table. | |
| swL3Md5Entry | 1.3.6.1.4.1.171.11.133.4.1.3.4.1 | not-accessible | A list of information displays the current MD5 key table. | |
| INT swL3Md5KeyId | 1.3.6.1.4.1.171.11.133.4.1.3.4.1.1 | INTEGER | read-only | The MD5 key ID. |
| STR swL3Md5Key | 1.3.6.1.4.1.171.11.133.4.1.3.4.1.2 | DisplayString | read-create | An MD5 password of up to 16 bytes. |
| ROW swL3Md5RowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.4.1.3 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3RouteRedistriTable | 1.3.6.1.4.1.171.11.133.4.1.3.5 | not-accessible | Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol. | |
| swL3RouteRedistriEntry | 1.3.6.1.4.1.171.11.133.4.1.3.5.1 | not-accessible | A list of information displaying the route redistribution table. | |
| INT swL3RouteRedistriSrcProtocol | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.1 | INTEGER | read-only | Allows the selection of the protocol of the source device. |
| INT swL3RouteRedistriDstProtocol | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.2 | INTEGER | read-only | Allows the selection of the protocol of the destination device. |
| INT swL3RouteRedistriType | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.3 | INTEGER | read-create | Allows the selection of one of the methods for calculating the metric value. |
| U32 swL3RouteRedistriMetric | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.4 | Unsigned32 | read-create | Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value. |
| ROW swL3RouteRedistriRowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.5 | RowStatus | read-create | This object indicates the status of this entry. |
| STR swL3RouteRedistriRouteMapName | 1.3.6.1.4.1.171.11.133.4.1.3.5.1.6 | DisplayString | read-create | This Object just works when the destination protocol is BGP and indicate the route-map working when redistribute the route to BGP. |
| swL3OspfHostTable | 1.3.6.1.4.1.171.11.133.4.1.3.6 | not-accessible | The list of Hosts, and their metrics, that the router will advertise as host routes. | |
| swL3OspfHostEntry | 1.3.6.1.4.1.171.11.133.4.1.3.6.1 | not-accessible | A metric to be advertised, for a given type of service, when a given host is reachable. | |
| IP swL3OspfHostIpAddress | 1.3.6.1.4.1.171.11.133.4.1.3.6.1.1 | IpAddress | read-only | The IP Address of the Host. |
| TOS swL3OspfHostTOS | 1.3.6.1.4.1.171.11.133.4.1.3.6.1.2 | TOSType | read-only | The Type of Service of the route being configured. |
| MET swL3OspfHostMetric | 1.3.6.1.4.1.171.11.133.4.1.3.6.1.3 | Metric | read-create | The Metric to be advertised. |
| ARE swL3OspfHostAreaID | 1.3.6.1.4.1.171.11.133.4.1.3.6.1.4 | AreaID | read-create | The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0 |
| ROW swL3OspfHostStatus | 1.3.6.1.4.1.171.11.133.4.1.3.6.1.5 | RowStatus | read-create | This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. |
| swL3ospfVirtIfTable | 1.3.6.1.4.1.171.11.133.4.1.3.7 | not-accessible | Information about this router's virtual inter- faces. | |
| swL3ospfVirtIfEntry | 1.3.6.1.4.1.171.11.133.4.1.3.7.1 | not-accessible | Information about a single Virtual Interface. | |
| ARE swL3ospfVirtIfAreaId | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.1 | AreaID | read-only | The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0 |
| ROU swL3ospfVirtIfNeighbor | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.2 | RouterID | read-only | The Router ID of the Virtual Neighbor. |
| UPT swL3ospfVirtIfTransitDelay | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.3 | UpToMaxAge | read-create | The estimated number of seconds it takes to transmit a link- state update packet over this interface. |
| UPT swL3ospfVirtIfRetransInterval | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.4 | UpToMaxAge | read-create | The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time. |
| HEL swL3ospfVirtIfHelloInterval | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.5 | HelloRange | read-create | The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor. |
| I32 swL3ospfVirtIfRtrDeadInterval | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.6 | Integer32 | read-create | The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor. |
| INT swL3ospfVirtIfState | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.7 | INTEGER | read-only | OSPF virtual interface states. |
| C32 swL3ospfVirtIfEventsEx | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.8 | Counter32 | read-only | The number of state changes or error events on this Virtual Link |
| INT swL3ospfVirtIfAuthType | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.9 | INTEGER | read-create | The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally. |
| OCT swL3ospfVirtIfAuthKey | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.10 | OCTET STRING | read-create | If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. |
| INT swL3ospfVirtIfAuthKeyID | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.11 | INTEGER | read-create | The MD5 key ID. |
| ROW swL3ospfVirtIfStatus | 1.3.6.1.4.1.171.11.133.4.1.3.7.1.12 | RowStatus | read-create | This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. |
| swL3ospfIfTable | 1.3.6.1.4.1.171.11.133.4.1.3.8 | not-accessible | The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. | |
| swL3ospfIfEntry | 1.3.6.1.4.1.171.11.133.4.1.3.8.1 | not-accessible | The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. | |
| IP swL3ospfIfIpAddress | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.1 | IpAddress | read-only | The IP address of this OSPF interface. |
| I32 swL3ospfAddressLessIf | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.2 | Integer32 | read-only | For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address. |
| ARE swL3ospfIfAreaId | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.3 | AreaID | read-write | A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. |
| INT swL3ospfIfType | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.4 | INTEGER | read-write | The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'. |
| STA swL3ospfIfAdminStat | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.5 | Status | read-write | The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF. |
| DES swL3ospfIfRtrPriority | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.6 | DesignatedRouterPriority | read-write | The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker. |
| UPT swL3ospfIfTransitDelay | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.7 | UpToMaxAge | read-write | The estimated number of seconds it takes to transmit a link state update packet over this interface. |
| UPT swL3ospfIfRetransInterval | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.8 | UpToMaxAge | read-write | The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. |
| HEL swL3ospfIfHelloInterval | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.9 | HelloRange | read-write | The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network. |
| NUM swL3ospfIfRtrDeadInterval | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.10 | PositiveInteger | read-write | The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. |
| NUM swL3ospfIfPollInterval | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.11 | PositiveInteger | read-write | The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor. |
| INT swL3ospfIfState | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.12 | INTEGER | read-only | The OSPF Interface State. |
| IP swL3ospfIfDesignatedRouter | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.13 | IpAddress | read-only | The IP Address of the Designated Router. |
| IP swL3ospfIfBackupDesignatedRouter | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.14 | IpAddress | read-only | The IP Address of the Backup Designated Router. |
| C32 swL3ospfIfEvents | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.15 | Counter32 | read-only | The number of times this OSPF interface has changed its state, or an error has occurred. |
| INT swL3ospfIfMulticastForwarding | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.16 | INTEGER | read-write | The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding. |
| T/F swL3ospfIfDemand | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.17 | TruthValue | read-write | Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface. |
| INT swL3ospfIfAuthType | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.18 | INTEGER | read-write | The authentication type specified for an in- terface. Additional authentication types may be assigned locally. |
| OCT swL3ospfIfAuthKey | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.19 | OCTET STRING | read-write | The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero. |
| INT swL3ospfIfAuthKeyID | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.20 | INTEGER | read-write | The MD5 key ID. |
| INT swL3ospfIfPassiveMode | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.21 | INTEGER | read-write | Assign the designated entry to be a passive interface. |
| MET swL3ospfIfMetric | 1.3.6.1.4.1.171.11.133.4.1.3.8.1.23 | Metric | read-write | The Metric to be advertised. |
| swL3RoutePreference | 1.3.6.1.4.1.171.11.133.4.1.3.9 | |||
| INT swL3RoutePreferenceRIP | 1.3.6.1.4.1.171.11.133.4.1.3.9.1 | INTEGER | read-write | Used to configure the route preference of RIP. |
| INT swL3RoutePreferenceOSPFIntra | 1.3.6.1.4.1.171.11.133.4.1.3.9.2 | INTEGER | read-write | Used to configure the route preference of OSPF Intra. |
| INT swL3RoutePreferenceStatic | 1.3.6.1.4.1.171.11.133.4.1.3.9.3 | INTEGER | read-write | Used to configure the route preference of Static. |
| INT swL3RoutePreferenceLocal | 1.3.6.1.4.1.171.11.133.4.1.3.9.4 | INTEGER | read-only | Used to read the route preference of Local. |
| INT swL3RoutePreferenceOSPFInter | 1.3.6.1.4.1.171.11.133.4.1.3.9.5 | INTEGER | read-write | Used to configure the route preference of OSPF Inter. |
| INT swL3RoutePreferenceOSPFExtT1 | 1.3.6.1.4.1.171.11.133.4.1.3.9.6 | INTEGER | read-write | Used to configure the route preference of OSPFExtT1. |
| INT swL3RoutePreferenceOSPFExtT2 | 1.3.6.1.4.1.171.11.133.4.1.3.9.7 | INTEGER | read-write | Used to configure the route preference of OSPF ExtT2. |
| INT swL3RoutePreferenceDefault | 1.3.6.1.4.1.171.11.133.4.1.3.9.8 | INTEGER | read-write | Used to configure the route preference of Default route. |
| INT swL3RoutePreferenceEBGP | 1.3.6.1.4.1.171.11.133.4.1.3.9.9 | INTEGER | read-write | Used to configure the route preference of EBGP. |
| INT swL3RoutePreferenceIBGP | 1.3.6.1.4.1.171.11.133.4.1.3.9.10 | INTEGER | read-write | Used to configure the route preference of IBGP. |
| swL3ospfAreaTable | 1.3.6.1.4.1.171.11.133.4.1.3.10 | not-accessible | Information describing the configured parame- ters and cumulative statistics of the router's attached areas. | |
| swL3ospfAreaEntry | 1.3.6.1.4.1.171.11.133.4.1.3.10.1 | not-accessible | Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas. | |
| ARE swL3ospfAreaId | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.1 | AreaID | read-only | A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone. |
| INT swL3ospfAreaType | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.2 | INTEGER | read-create | The type specified for an area. |
| INT swL3ospfAreaSummaryState | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.3 | INTEGER | read-create | Whether the summary LSA is effective for this area. |
| I32 swL3ospfAreaMetric | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.4 | Integer32 | read-write | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| INT swL3ospfAreaTranslateState | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.5 | INTEGER | read-create | . |
| ROW swL3ospfAreaStatus | 1.3.6.1.4.1.171.11.133.4.1.3.10.1.6 | RowStatus | read-create | This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. |
| swL3dvmrpInterfaceTable | 1.3.6.1.4.1.171.11.133.4.1.3.12 | not-accessible | The (conceptual) table listing the router's multicast- capable interfaces. | |
| swL3dvmrpInterfaceEntry | 1.3.6.1.4.1.171.11.133.4.1.3.12.1 | not-accessible | An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides. | |
| I32 swL3dvmrpInterfaceIfIndex | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.1 | Integer32 | not-accessible | The ifIndex value of the interface for which DVMRP is enabled. |
| IP swL3dvmrpInterfaceLocalAddress | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.2 | IpAddress | read-create | The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress for some interface on the system. |
| I32 swL3dvmrpInterfaceMetric | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.3 | Integer32 | read-create | The distance metric for this interface which is used to calculate distance vectors. |
| I32 swL3dvmrpInterfaceProbe | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.4 | Integer32 | read-create | Probe distribution interval. |
| I32 swL3dvmrpInterfaceNbrTimeout | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.5 | Integer32 | read-create | Used to set the timer before neighbors are timed out. |
| ROW swL3dvmrpInterfaceStatus | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.6 | RowStatus | read-create | The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the virtual interface. |
| C32 swL3dvmrpInterfaceRcvBadPkts | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.7 | Counter32 | read-only | The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route report from an unknown neighbor). |
| C32 swL3dvmrpInterfaceRcvBadRoutes | 1.3.6.1.4.1.171.11.133.4.1.3.12.1.8 | Counter32 | read-only | The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid. |
| swL3OspfLsdbMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.13 | |||
| swL3OspfInternalLsdbTable | 1.3.6.1.4.1.171.11.133.4.1.3.13.1 | not-accessible | The OSPF Process's Link State Database. | |
| swL3OspfInternalLsdbEntry | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1 | not-accessible | A single Link State Advertisement. | |
| ARE swL3OspfInternalLsdbAreaId | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.1 | AreaID | read-only | The 32 bit identifier of the Area from which the LSA was received. |
| INT swL3OspfInternalLsdbType | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.2 | INTEGER | read-only | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| IP swL3OspfInternalLsdbLsid | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.3 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU swL3OspfInternalLsdbRouterId | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.4 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 swL3OspfInternalLsdbMetric | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.5 | Integer32 | read-only | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| OCT swL3OspfInternalLsdbSequenceNo | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.6 | OCTET STRING | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| U32 swL3OspfInternalLsdbAge | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.7 | Unsigned32 | read-only | This field is the age of the link state adver- tisement in seconds. |
| I32 swL3OspfInternalLsdbChecksum | 1.3.6.1.4.1.171.11.133.4.1.3.13.1.1.8 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. |
| swL3OspfExternalLsdbTable | 1.3.6.1.4.1.171.11.133.4.1.3.13.2 | not-accessible | The OSPF Process's Links State Database. | |
| swL3OspfExternalLsdbEntry | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1 | not-accessible | A single Link State Advertisement. | |
| INT swL3OspfExternalLsdbType | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.1 | INTEGER | read-only | The type of the link state advertisement. Each link state type has a separate advertise- ment format. |
| IP swL3OspfExternalLsdbLsid | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.2 | IpAddress | read-only | The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. |
| ROU swL3OspfExternalLsdbRouterId | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.3 | RouterID | read-only | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 swL3OspfExternalLsdbMetric | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.4 | Integer32 | read-only | Enter the metric (1 - 65535; 0 for auto cost) of this area. |
| INT swL3OspfExternalLsdbMetricType | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.5 | INTEGER | read-only | Enter the metric type of this area. |
| OCT swL3OspfExternalLsdbSequenceNo | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.6 | OCTET STRING | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| U32 swL3OspfExternalLsdbAge | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.7 | Unsigned32 | read-only | This field is the age of the link state adver- tisement in seconds. |
| I32 swL3OspfExternalLsdbChecksum | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.8 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, except the age field. The age field is the exception so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. |
| IP swL3OspfExternalLsdbForwardingAddress | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.9 | IpAddress | read-only | This field is the forwarding address. |
| OCT swL3OspfExternalLsdbRouteTag | 1.3.6.1.4.1.171.11.133.4.1.3.13.2.1.10 | OCTET STRING | read-only | This field is the route tag. |
| swL3VrrpOperMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.14 | |||
| swL3VrrpOperTable | 1.3.6.1.4.1.171.11.133.4.1.3.14.1 | not-accessible | Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3vrrpOperEntry' items. | |
| swL3VrrpOperEntry | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1 | not-accessible | An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. Rows in the table cannot be modified unless the value of `swL3VrrpOperAdminState' is `disabled' and the `swL3VrrpOperState' has transitioned to `initialize'. | |
| I32 swL3VrrpOperIfIndex | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.1 | Integer32 | read-only | The ifIndex value of the interface for which VRRP is enabled. |
| VRI swL3VrrpOperVrId | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.2 | VrId | read-only | This object contains the Virtual Router Identifier (VRID). |
| MAC swL3VrrpOperVirtualMacAddr | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.3 | MacAddress | read-only | The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps. |
| INT swL3VrrpOperState | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.4 | INTEGER | read-only | The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router. Setting the `swL3VrrpOperAdminState' object (below) initiates transitions in the value of this object. |
| INT swL3VrrpOperAdminState | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.5 | INTEGER | read-create | This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `swL3VrrpOperPriority'. Setting the value to `down', will transition the router from `master' or `backup' to `initialize'. State transitions may not be immediate; they sometimes depend on other factors, such as the interface (IF) state. The `swL3VrrpOperAdminState' object must be set to `down' prior to modifying the other read-create objects in the conceptual row. The value of the `swL3VrrpOperRowStatus' object (below) must be `active', signifying that the conceptual row is valid (i.e., the objects are correctly set), in order for this object to be set to `up'. |
| I32 swL3VrrpOperPriority | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.6 | Integer32 | read-create | This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es). |
| IP swL3VrrpOperMasterIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.7 | IpAddress | read-only | The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router. |
| IP swL3VrrpOperCriticalIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.8 | IpAddress | read-create | In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMasterIpAddr', should the virtual router transition from backup to master. If this object is set to 0.0.0.0, the IP address which is numerically lowest will be selected. |
| INT swL3VrrpOperCheckCriticalIpState | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.9 | INTEGER | read-create | Critical IP state. |
| INT swL3VrrpOperAuthType | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.10 | INTEGER | read-create | Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to this list can only be added via a new RFC on the standards track. |
| OCT swL3VrrpOperAuthKey | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.11 | OCTET STRING | read-create | The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent will left adjust and zero fill to 16 octets. The value of this object is the same for a given ifIndex. When read, swL3VrrpOperAuthKey always returns an Octet String of length zero. |
| I32 swL3VrrpOperAdvertisementInterval | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.12 | Integer32 | read-create | The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements. |
| T/F swL3VrrpOperPreemptMode | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.13 | TruthValue | read-create | Controls whether a higher priority virtual router will preempt a lower priority master. |
| TIM swL3VrrpOperVirtualRouterUpTime | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.14 | TimeStamp | read-only | This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'. |
| IP swL3VrrpOperVirtualIpAddr | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.15 | IpAddress | read-create | The assigned IP addresses that a virtual router is responsible for backing up. |
| ROW swL3VrrpOperRowStatus | 1.3.6.1.4.1.171.11.133.4.1.3.14.1.1.16 | RowStatus | read-create | The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corresponding virtual router. When `vrrpOperRowStatus' is set to active(1), no other objects in the conceptual row, with the exception of `swL3VrrpOperAdminState', can be modified. Prior to setting the `swL3VrrpOperRowStatus' object from `active' to a different value, the `swL3VrrpOperAdminState' object must be set to `down' and the `vrrpOperState' object be transitioned to `initialize'. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `vrrpOperRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of `swL3VrrpOperVrId' has been set and there is at least one active row in the `swL3VrrpAssoIpAddrTable' defining an associated IP address for the virtual router. |
| swL3OspfECMPMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.15 | |||
| INT swL3OspfECMPIpDestination | 1.3.6.1.4.1.171.11.133.4.1.3.15.1 | INTEGER | read-write | If set to 'enabled (1)', the ECMP algorithm will include the destination IP. |
| INT swL3OspfECMPIpSource | 1.3.6.1.4.1.171.11.133.4.1.3.15.2 | INTEGER | read-write | If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the source IP. This attribution is mutually exclusive with crc_low and crc_high. If set to 'enabled (1)', crc_low and crc_high will be excluded. |
| INT swL3OspfECMPCrcLow | 1.3.6.1.4.1.171.11.133.4.1.3.15.3 | INTEGER | read-write | If set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the CRC. This attribution is mutually exclusive with crc_high and ip_source. If set to 'enabled (1)', crc_high and ip_source will be excluded. |
| INT swL3OspfECMPCrcHigh | 1.3.6.1.4.1.171.11.133.4.1.3.15.4 | INTEGER | read-write | If set to 'enabled (1)', the ECMP algorithm will include the upper 5 bits of the CRC. This attribution is mutually exclusive with ip_source and crc_low. If set to 'enabled (1)', crc_low and ip_source will be excluded. |
| INT swL3OspfECMPTCPorUDPport | 1.3.6.1.4.1.171.11.133.4.1.3.15.5 | INTEGER | read-write | If set to 'enabled (1)', the ECMP algorithm will include the TCP or UDP port. |
| INT swL3OspfECMPState | 1.3.6.1.4.1.171.11.133.4.1.3.15.6 | INTEGER | read-write | This object indicates the state of the OSPF ECMP function. |
| swL3LocalRouteMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.16 | |||
| INT swL3LocalRouteIPv4GlobalState | 1.3.6.1.4.1.171.11.133.4.1.3.16.1 | INTEGER | read-write | This object indicates the IPv4 local route state of the device. |
| INT swL3LocalRouteIPv6GlobalState | 1.3.6.1.4.1.171.11.133.4.1.3.16.2 | INTEGER | read-write | This object indicates the IPv6 local route state of the device. |
| swL3RIPTimerMgmt | 1.3.6.1.4.1.171.11.133.4.1.3.17 | |||
| INT swL3RIPUpdateTime | 1.3.6.1.4.1.171.11.133.4.1.3.17.1 | INTEGER | read-write | This object indicates the RIP update interval. |
| INT swL3RIPTimeOutTime | 1.3.6.1.4.1.171.11.133.4.1.3.17.2 | INTEGER | read-write | This object indicates the period for which a dynamic RIP route will be kept in the IPv4 routing table without receiving any updates for the route. After this time interval, the route will be invalid and will be aged out. |
| INT swL3RIPGarbageCollectionTime | 1.3.6.1.4.1.171.11.133.4.1.3.17.3 | INTEGER | read-write | This object indicates the period for a RIP route which has aged out is retained in the IPv4 Routing Table. After this time interval the route is deleted from the IPv4 Routing Table. |
RFC description
D-Link DGS3000-24TC Layer 3 network management with routing and advanced IP features.
Start monitoring D-Link DGS-3000-24TC Layer 3 switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.