All MIBs › DES-2110-MIB
Category: VLAN and Bridging, Vendor: D-Link
Description: Manages D-Link DES-2110 smart switch port configuration, VLANs, and basic L2 management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DES-2110-MIB?
DES-2110-MIB is the device-specific enterprise MIB for the D-Link DES-2110 smart switch, providing port configuration, VLAN, and basic Layer 2 management objects specific to that product. Consistent with D-Link's smart-switch tier, it would be expected to expose per-port configuration and VLAN assignment along with basic switch system status rather than advanced routing or deep environmental sensors. No concrete object or table names were available in this extract, so specific monitored parameters cannot be confirmed with certainty here. It would typically be used alongside standard IF-MIB and BRIDGE-MIB objects for a fuller view of interface and VLAN/bridging state. It is deployed in small business or branch-office environments using the D-Link DES-2110 switch for basic managed Layer 2 connectivity. Engineers can download the DES-2110-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DES-2110-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link DES-2110 smart switch
Monitoring Examples
No sample object names were available in this extract, so a concrete polling scenario cannot be honestly constructed. Typically a MIB of this kind would be polled for per-port configuration and VLAN assignment, but specifics are not confirmed for this module.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress | |
| mib-2 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| d_link | 1.3.6.1.4.1.171 | |||
| dlink_products | 1.3.6.1.4.1.171.10 | |||
| dlink_DES21XXSeriesProd | 1.3.6.1.4.1.171.10.61 | |||
| des_2110 | 1.3.6.1.4.1.171.10.61.1 | |||
| NTF swFiberInsert | 1.3.6.1.4.1.171.10.61.1.0.1 | Fiber insert trap | ||
| NTF swFiberRemove | 1.3.6.1.4.1.171.10.61.1.0.2 | Fiber remove trap | ||
| NTF swFiberAbnormalRXError | 1.3.6.1.4.1.171.10.61.1.0.3 | Fiber abnormal rx error trap | ||
| NTF swFiberAbnormalTXError | 1.3.6.1.4.1.171.10.61.1.0.4 | Fiber abnormal tx error trap | ||
| NTF swTPAbnormalRXError | 1.3.6.1.4.1.171.10.61.1.0.5 | Twisted Pair abnormal rx error trap | ||
| NTF swTPAbnormalTXError | 1.3.6.1.4.1.171.10.61.1.0.6 | Twisted Pair abnormal tx error trap | ||
| companyCommGroup | 1.3.6.1.4.1.171.10.61.1.1 | |||
| commSetTable | 1.3.6.1.4.1.171.10.61.1.1.1 | not-accessible | A list of SNMP Set Community Entries | |
| commSetEntry | 1.3.6.1.4.1.171.10.61.1.1.1.1 | not-accessible | A list of SNMP Set Community properties | |
| INT commSetIndex | 1.3.6.1.4.1.171.10.61.1.1.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commSetName | 1.3.6.1.4.1.171.10.61.1.1.1.1.2 | DisplayString | read-write | The name of this SNMP Set Community Entry. |
| ROW commSetStatus | 1.3.6.1.4.1.171.10.61.1.1.1.1.3 | RowStatus | read-write | The RowStatus for the Set Community entry. |
| commGetTable | 1.3.6.1.4.1.171.10.61.1.1.2 | not-accessible | A list of SNMP Get Community Entries | |
| commGetEntry | 1.3.6.1.4.1.171.10.61.1.1.2.1 | not-accessible | A list of SNMP Get Community properties | |
| INT commGetIndex | 1.3.6.1.4.1.171.10.61.1.1.2.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commGetName | 1.3.6.1.4.1.171.10.61.1.1.2.1.2 | DisplayString | read-write | The name of this SNMP Get Community Entry. |
| ROW commGetStatus | 1.3.6.1.4.1.171.10.61.1.1.2.1.3 | RowStatus | read-write | The RowStatus for the Get Community entry. |
| commTrapTable | 1.3.6.1.4.1.171.10.61.1.1.3 | not-accessible | A list of SNMP Trap Community Entries | |
| commTrapEntry | 1.3.6.1.4.1.171.10.61.1.1.3.1 | not-accessible | A list of SNMP Trap Community properties | |
| INT commTrapIndex | 1.3.6.1.4.1.171.10.61.1.1.3.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commTrapName | 1.3.6.1.4.1.171.10.61.1.1.3.1.2 | DisplayString | read-write | The name of this SNMP Trap Community Entry. |
| IP commTrapIpAddress | 1.3.6.1.4.1.171.10.61.1.1.3.1.3 | IpAddress | read-write | The IP Address of this SNMP Trap Community Entry. |
| INT commTrapVlanId | 1.3.6.1.4.1.171.10.61.1.1.3.1.4 | INTEGER | read-write | The Trap VLAN identifier of this SNMP Trap Community Entry. The value must be from 1 to 4094. |
| INT commTrapSNMPBootup | 1.3.6.1.4.1.171.10.61.1.1.3.1.5 | INTEGER | read-write | Bootup trap |
| INT commTrapSNMPTPLinkUpDown | 1.3.6.1.4.1.171.10.61.1.1.3.1.6 | INTEGER | read-write | Twisted Pair link up / link down trap |
| INT commTrapSNMPFiberLinkUpDown | 1.3.6.1.4.1.171.10.61.1.1.3.1.7 | INTEGER | read-write | Fiber link up / link down trap |
| INT commTrapTrapAbnormalTPRXError | 1.3.6.1.4.1.171.10.61.1.1.3.1.9 | INTEGER | read-write | Twisted Pair abnormal receive error trap |
| INT commTrapTrapAbnormalTPTXError | 1.3.6.1.4.1.171.10.61.1.1.3.1.10 | INTEGER | read-write | Twisted Pair abnormal transmit error trap |
| INT commTrapTrapAbnormalFiberRXError | 1.3.6.1.4.1.171.10.61.1.1.3.1.11 | INTEGER | read-write | Fiber abnormal receive error trap |
| INT commTrapTrapAbnormalFiberTXError | 1.3.6.1.4.1.171.10.61.1.1.3.1.12 | INTEGER | read-write | Fiber abnormal transmit error trap |
| ROW commTrapStatus | 1.3.6.1.4.1.171.10.61.1.1.3.1.13 | RowStatus | read-write | The RowStatus for the Trap Community entry. |
| companyMiscGroup | 1.3.6.1.4.1.171.10.61.1.3 | |||
| INT miscReset | 1.3.6.1.4.1.171.10.61.1.3.2 | INTEGER | read-write | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| INT miscStatisticsReset | 1.3.6.1.4.1.171.10.61.1.3.3 | INTEGER | read-write | Resets the units statistics. A (1) resets the unit, a (2) does nothing. |
| companySpanGroup | 1.3.6.1.4.1.171.10.61.1.4 | |||
| INT spanOnOff | 1.3.6.1.4.1.171.10.61.1.4.1 | INTEGER | read-write | Enable/Disable Spanning Tree. A (1) enables, a (2) disables. |
| companyConfigGroup | 1.3.6.1.4.1.171.10.61.1.11 | |||
| STR configVerSwPrimary | 1.3.6.1.4.1.171.10.61.1.11.1 | DisplayString | read-only | The software image version string |
| STR configVerHwChipSet | 1.3.6.1.4.1.171.10.61.1.11.2 | DisplayString | read-only | The hardware chipset version string |
| configPortTable | 1.3.6.1.4.1.171.10.61.1.11.6 | not-accessible | A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces. | |
| configPortEntry | 1.3.6.1.4.1.171.10.61.1.11.6.1 | not-accessible | An enterprise specific interface entry. | |
| INT configPort | 1.3.6.1.4.1.171.10.61.1.11.6.1.1 | INTEGER | read-only | A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber. |
| INT configPortSpeed | 1.3.6.1.4.1.171.10.61.1.11.6.1.2 | INTEGER | read-write | The port's speed desired state. |
| INT configPortOperStatus | 1.3.6.1.4.1.171.10.61.1.11.6.1.3 | INTEGER | read-only | The port's operating speed state. |
| INT configPortFlowControl | 1.3.6.1.4.1.171.10.61.1.11.6.1.4 | INTEGER | read-write | The port will avoid transmitting a new packet for the period of time specified in a received PAUSE packet when enabled. |
| INT configPortFlowControlOper | 1.3.6.1.4.1.171.10.61.1.11.6.1.5 | INTEGER | read-only | The port's operating flow control state. |
| INT configPortPriority | 1.3.6.1.4.1.171.10.61.1.11.6.1.6 | INTEGER | read-write | The port's current priority. |
| INT configVLANMode | 1.3.6.1.4.1.171.10.61.1.11.7 | INTEGER | read-write | Determines the VLAN mode. |
| configMirrorTable | 1.3.6.1.4.1.171.10.61.1.11.8 | not-accessible | A list of the Mirror | |
| configMirrorEntry | 1.3.6.1.4.1.171.10.61.1.11.8.1 | not-accessible | A Mirror entry containing the Mirror id and mode | |
| INT configMirrorId | 1.3.6.1.4.1.171.10.61.1.11.8.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported. |
| INT configMirrorMode | 1.3.6.1.4.1.171.10.61.1.11.8.1.2 | INTEGER | read-write | When deciding the mirroring source port, then Mirror mode will be available. |
| INT configMirrorMon | 1.3.6.1.4.1.171.10.61.1.11.8.1.3 | INTEGER | read-write | When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled. |
| POR configMirrorSrc | 1.3.6.1.4.1.171.10.61.1.11.8.1.4 | PortList | read-write | When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring source port. This value has a valid range of 1 to ifNumber when enbaled. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| ROW configMirrorStatus | 1.3.6.1.4.1.171.10.61.1.11.8.1.5 | RowStatus | read-write | The RowStatus for the Mirror entry. |
| INT configSNMPEnable | 1.3.6.1.4.1.171.10.61.1.11.9 | INTEGER | read-write | Enable/Disable SNMP function. A (1) enables, a (2) disables. |
| INT configIpAssignmentMode | 1.3.6.1.4.1.171.10.61.1.11.12 | INTEGER | read-write | Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP). |
| MAC configPhysAddress | 1.3.6.1.4.1.171.10.61.1.11.13 | MacAddress | read-only | The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station. |
| STR configPasswordAdmin | 1.3.6.1.4.1.171.10.61.1.11.15 | DisplayString | write-only | The adminstrator password |
| IP configIpAddress | 1.3.6.1.4.1.171.10.61.1.11.16 | IpAddress | read-write | The IP Address for the RDU box. |
| IP configNetMask | 1.3.6.1.4.1.171.10.61.1.11.17 | IpAddress | read-write | The network mask for the RDU box. |
| IP configGateway | 1.3.6.1.4.1.171.10.61.1.11.18 | IpAddress | read-write | The Gatway Address for the unit. |
| INT configSave | 1.3.6.1.4.1.171.10.61.1.11.19 | INTEGER | read-write | Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing. |
| INT configRestoreDefaults | 1.3.6.1.4.1.171.10.61.1.11.22 | INTEGER | read-write | Restores the configuration of the unit to the original settings. |
| companyPVlanGroup | 1.3.6.1.4.1.171.10.61.1.12 | |||
| pvlanTable | 1.3.6.1.4.1.171.10.61.1.12.1 | not-accessible | A list of the Port-based VLANs | |
| pvlanEntry | 1.3.6.1.4.1.171.10.61.1.12.1.1 | not-accessible | A Port-based VLAN entry containing the id and name. | |
| INT pvlanId | 1.3.6.1.4.1.171.10.61.1.12.1.1.1 | INTEGER | read-only | The VLAN identifier. A maximum of 28 VLANs is supported. The value must be from 1 to 28 |
| STR pvlanName | 1.3.6.1.4.1.171.10.61.1.12.1.1.2 | DisplayString | read-write | The VLAN name associated with the Id. |
| POR pvlanMember | 1.3.6.1.4.1.171.10.61.1.12.1.1.3 | PortList | read-write | The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| INT pvlanStatus | 1.3.6.1.4.1.171.10.61.1.12.1.1.5 | INTEGER | read-write | The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| companyTVlanGroup | 1.3.6.1.4.1.171.10.61.1.13 | |||
| tvlanTable | 1.3.6.1.4.1.171.10.61.1.13.1 | not-accessible | A list of the VLANs | |
| tvlanEntry | 1.3.6.1.4.1.171.10.61.1.13.1.1 | not-accessible | A VLAN entry containing the VLAN id and name. | |
| INT tvlanId | 1.3.6.1.4.1.171.10.61.1.13.1.1.1 | INTEGER | read-only | The VLAN identifier. A maximum of 64 VLANs is supported. The value must be from 1 to 4094. |
| POR tvlanMember | 1.3.6.1.4.1.171.10.61.1.13.1.1.3 | PortList | read-write | The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| POR tvlanUntaggedPorts | 1.3.6.1.4.1.171.10.61.1.13.1.1.4 | PortList | read-write | If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged. |
| INT tvlanStatus | 1.3.6.1.4.1.171.10.61.1.13.1.1.5 | INTEGER | read-write | The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| tvlanPortTable | 1.3.6.1.4.1.171.10.61.1.13.2 | not-accessible | A list of ports and their associated VLAN. | |
| tvlanPortEntry | 1.3.6.1.4.1.171.10.61.1.13.2.1 | not-accessible | Information pertaining to an individual port regarding to which VLAN it belongs. | |
| INT tvlanPortPortId | 1.3.6.1.4.1.171.10.61.1.13.2.1.1 | INTEGER | read-only | A port identifier that is in the range of 1 to ifNumber. |
| INT tvlanPortVlanId | 1.3.6.1.4.1.171.10.61.1.13.2.1.2 | INTEGER | read-write | The default VLAN identifier. |
| INT tvlanPortPriority | 1.3.6.1.4.1.171.10.61.1.13.2.1.3 | INTEGER | read-write | The default priority. |
| INT tvlanManagement | 1.3.6.1.4.1.171.10.61.1.13.3 | INTEGER | read-write | The management vlan which allow to forwarding to cpu. |
| companyStaticGroup | 1.3.6.1.4.1.171.10.61.1.21 | |||
| INT staticOnOff | 1.3.6.1.4.1.171.10.61.1.21.1 | INTEGER | read-write | Enable/Disable Static MAC. A (1) enables, a (2) disables. |
| POR staticAutoLearning | 1.3.6.1.4.1.171.10.61.1.21.2 | PortList | read-write | The set of the device's member ports that belong to the Static MAC auto learning enable/disable. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is in auto learning enable state; the port is not in auto learning state if its bit has a value of '0'. |
| staticTable | 1.3.6.1.4.1.171.10.61.1.21.3 | not-accessible | A list of the Static MACs | |
| staticEntry | 1.3.6.1.4.1.171.10.61.1.21.3.1 | not-accessible | A Static MAC entry containing the mac and forwarding port. | |
| INT staticId | 1.3.6.1.4.1.171.10.61.1.21.3.1.1 | INTEGER | read-only | The Static MAC identifier. A maximum of 60 Static MACs is supported. The value must be from 1 to 60 |
| STR staticMac | 1.3.6.1.4.1.171.10.61.1.21.3.1.2 | DisplayString | read-write | The Static MAC associated with the Id. |
| INT staticPort | 1.3.6.1.4.1.171.10.61.1.21.3.1.3 | INTEGER | read-write | The Static MAC forwarding port with the ID. |
| INT staticVlanID | 1.3.6.1.4.1.171.10.61.1.21.3.1.4 | INTEGER | read-write | The Static MAC VLAN ID with the ID. |
| INT staticStatus | 1.3.6.1.4.1.171.10.61.1.21.3.1.5 | INTEGER | read-write | The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| companyIgsGroup | 1.3.6.1.4.1.171.10.61.1.22 | |||
| igsSystem | 1.3.6.1.4.1.171.10.61.1.22.1 | |||
| INT igsStatus | 1.3.6.1.4.1.171.10.61.1.22.1.2 | INTEGER | read-write | Enables or disables IGMP snooping in the system |
| INT igsRouterPortPurgeInterval | 1.3.6.1.4.1.171.10.61.1.22.1.4 | INTEGER | read-write | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, a 'RouterPortPurgeTimer' runs for 'RouterPortPurgeInterval'. This timer will be restarted whenever a router control message is received over that port. If no router control mssages are received for 'RouterPortPurgeInterval' time, the learnt router port entry will be purged |
| INT igsHostPortPurgeInterval | 1.3.6.1.4.1.171.10.61.1.22.1.5 | INTEGER | read-write | This is the interval (in seconds) after which a learnt host port entry will be purged. For each host port learnt, a 'PortPurgeTimer' runs for 'HostPortPurgeInterval'. This timer will be restarted whenever a report message from host is received over that port. If no report mssages are received for 'HostPortPurgeInterval' time, the learnt host entry will be purged from the multicast group |
| igsBrg | 1.3.6.1.4.1.171.10.61.1.22.2 | |||
| POR igsBrgRouterPortList | 1.3.6.1.4.1.171.10.61.1.22.2.1 | PortList | read-write | Contains list of bridge ports through which a router is reachable. These router ports can be learnt through control messages received from routers, and statically configured |
| igsBrgMcastFwdTable | 1.3.6.1.4.1.171.10.61.1.22.2.2 | not-accessible | This table contains multicast forwarding information learnt when VLAN is DISABLED in the system. | |
| igsBrgMcastFwdEntry | 1.3.6.1.4.1.171.10.61.1.22.2.2.1 | not-accessible | This table contains multicast group address and the list of ports who have members for the multicast group. | |
| MAC igsBrgMcastFwdGroupAddress | 1.3.6.1.4.1.171.10.61.1.22.2.2.1.1 | MacAddress | not-accessible | MAC multicast group address. |
| POR igsBrgMcastFwdPortListMac | 1.3.6.1.4.1.171.10.61.1.22.2.2.1.2 | PortList | read-only | List of ports who have members for the MAC multicast group. |
| companyStormCtrlGroup | 1.3.6.1.4.1.171.10.61.1.23 | |||
| INT stormctrlOnOff | 1.3.6.1.4.1.171.10.61.1.23.1 | INTEGER | read-write | Enable/Disable ARP STORM CONTROL. A (1) enables, a (2) disables. |
| INT stormctrlStatus | 1.3.6.1.4.1.171.10.61.1.23.2 | INTEGER | read-write | Unlock ARP STORM CONTROL mechanism. A (1) locked, a (2) unlock. |
RFC description
Manages configuration and community settings for D-Link DES-2110 network switches.
Start monitoring D-Link DES-2110 smart switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.