CISCO-MGX82XX-TRAPS-MIB

All MIBs › CISCO-MGX82XX-TRAPS-MIB

Category: Alarm and Event Management, Cisco Devices, Device Management

Description: Defines SNMP trap notifications for fault and status events on Cisco MGX 8200 WAN switching platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-MGX82XX-TRAPS-MIB?

CISCO-MGX82XX-TRAPS-MIB is a Cisco enterprise MIB module that defines SNMP trap (notification) objects for fault and status events on the Cisco MGX 8200 series WAN switching platforms. Rather than exposing polled configuration or counter tables, its primary content is notification definitions used to asynchronously alert a management station about significant device events, likely including hardware faults, card/module state changes, and alarm conditions. As a monitoring resource its role is fault/event monitoring specifically - flagging hardware or software status changes (card failures, alarms, link state transitions) as they occur rather than through periodic polling of counters. It necessarily depends on the base CISCO-MGX82XX-MIB (or related MGX chassis/card MIBs) that defines the objects referenced within each trap's variable bindings. It is deployed on Cisco MGX 8200 series WAN switches in carrier/service-provider ATM/Frame Relay WAN aggregation networks to provide real-time fault alerting. Engineers can download the CISCO-MGX82XX-TRAPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-MGX82XX-TRAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco MGX 8200 series WAN switch

Monitoring Examples

No concrete trap or object names were captured in sample_objects, so a specific example cannot be grounded in verified names. Based on the module's stated purpose, a management station would typically subscribe to this MIB's traps to receive real-time alerts on MGX 8200 hardware faults or alarm state changes rather than by polling counters directly. This remains a general characterization of the module's fault-notification role rather than a verified example.

What Can Be Monitored

hardware fault/alarm trap events
card/module state-change trap events

Imported Objects

From BASIS-GENERIC-MIB

configChangeGrandParentObjectIndex	OBJECT-TYPE
configChangeObjectIndex	OBJECT-TYPE
configChangeParentObjectIndex	OBJECT-TYPE
configChangeSMSpecificObject	OBJECT-TYPE
configChangeStatus	OBJECT-TYPE
configChangeTypeBitMap	OBJECT-TYPE
functionModuleResetReason	OBJECT-TYPE
functionModuleState	OBJECT-TYPE
functionModuleType	OBJECT-TYPE
lineModuleState	OBJECT-TYPE
lineModuleType	OBJECT-TYPE
moduleSlotNumber	OBJECT-TYPE
moduleTrapAlarmSeverity	OBJECT-TYPE
secLineModuleState	OBJECT-TYPE
secLineModuleType	OBJECT-TYPE

From BASIS-MIB

basis

OBJECT-IDENTITY

From BASIS-RAS-DISK-MIB

crptdFWfiles	OBJECT-TYPE
crptdPRIfiles	OBJECT-TYPE
numBadSectors	OBJECT-TYPE
rasDskStatus	OBJECT-TYPE

From BASIS-SHELF-MIB

redPrimarySlotNum	OBJECT-TYPE
redPrimaryState	OBJECT-TYPE
redPrimaryType	OBJECT-TYPE
redSecondarySlotNum	OBJECT-TYPE
redSecondaryState	OBJECT-TYPE
redSecondaryType	OBJECT-TYPE
redType	OBJECT-TYPE
shelfFilteredAlarm	OBJECT-TYPE
shelfIntegratedAlarm	OBJECT-TYPE
shelfNodeName	OBJECT-TYPE
shelfNum	OBJECT-TYPE
shelfSlotNum	OBJECT-TYPE
userName	OBJECT-TYPE

From CISCO-MGX82XX-DSX1-MIB

almImaGrpNum
almlineNum
axisImaLinkNeRxFailureStatus
lineAlarmState	OBJECT-TYPE
lineImaAlarmState
lineNum	OBJECT-TYPE
lineStatisticalAlarmState	OBJECT-TYPE
lineType	OBJECT-TYPE
tCAlarmState

From CISCO-MGX82XX-DSX3-MIB

cwDsx3LineType	OBJECT-TYPE
dsx3FarEndLoopbkLineNum	OBJECT-TYPE
dsx3LineAlarmState	OBJECT-TYPE
dsx3LineEnable	OBJECT-TYPE
dsx3LineNum	OBJECT-TYPE
dsx3LineStatisticalAlarmState	OBJECT-TYPE
dsx3LineXmtClockSrc	OBJECT-TYPE
dsx3LineXmtFEACCode	OBJECT-TYPE
dsx3NearEndLoopbkLineStatus	OBJECT-TYPE
dsx3PlcpLineAlarmState	OBJECT-TYPE
dsx3PlcpLineStatisticalAlarmState	OBJECT-TYPE

From CISCO-MGX82XX-SONET-MIB

apsActiveLine	OBJECT-TYPE
apsCardFailureCode	OBJECT-TYPE
apsLineFailureCode	OBJECT-TYPE
apsLineSwFailureCode	OBJECT-TYPE
apsLineSwReason	OBJECT-TYPE
apsProtectionLine	OBJECT-TYPE
apsProtectionSlot	OBJECT-TYPE
apsStandbyLineFailureCode	OBJECT-TYPE
apsWorkingLine	OBJECT-TYPE
apsWorkingSlot	OBJECT-TYPE
cwSonetLineCurrentStatus	OBJECT-TYPE
sonetLineNum	OBJECT-TYPE
sonetLineStatAlarmStatus	OBJECT-TYPE
sonetLineType	OBJECT-TYPE
sonetLineXmtClkSrc	OBJECT-TYPE
sonetPathStatAlarmStatus	OBJECT-TYPE
sonetSectionStatAlarmStatus	OBJECT-TYPE

From CISCO-WAN-AXIPOP-MIB

asmAlarmUnitNum	OBJECT-TYPE
asmPhysicalAlarmState	OBJECT-TYPE
atmLineCnfNum	OBJECT-TYPE
atmLineInterfaceFormat	OBJECT-TYPE
ausmChanNum	OBJECT-TYPE
ausmChanPortNum	OBJECT-TYPE
ausmChanRowStatus	OBJECT-TYPE
ausmChanStatusBitMap	OBJECT-TYPE
ausmInterfaceMyNeighborIpAddress	OBJECT-TYPE
ausmInterfacePortNum	OBJECT-TYPE
ausmPortNum	OBJECT-TYPE
ausmPortState	OBJECT-TYPE
ausmSignallingProtocolType	OBJECT-TYPE
axisImaGroupFailureStatus	OBJECT-TYPE
axisImaGroupRxAvailCellRate	OBJECT-TYPE
axisImaGroupTxAvailCellRate	OBJECT-TYPE
bbChanCnfNum	OBJECT-TYPE
bbChanConnType	OBJECT-TYPE
bbChanIfNum	OBJECT-TYPE
bbChanVci	OBJECT-TYPE
bbChanVpi	OBJECT-TYPE
bbIfLineNum	OBJECT-TYPE
bbIfNum	OBJECT-TYPE
bbIfRscPrtRowStatus	OBJECT-TYPE
bbIfState	OBJECT-TYPE
bbRscPartCtrlrNum	OBJECT-TYPE
bertAbortReason	OBJECT-TYPE
bertLine	OBJECT-TYPE
bertPort	OBJECT-TYPE
bertSlotNumber	OBJECT-TYPE
bertStatus	OBJECT-TYPE
bertTestMedium	OBJECT-TYPE
bnmLineInterfaceFormat	OBJECT-TYPE
cardIngrPercentUtil	OBJECT-TYPE
cardLcnPartitionType	OBJECT-TYPE
cardOversubscribed	OBJECT-TYPE
cesChanPortNum	OBJECT-TYPE
cesChanRowStatus	OBJECT-TYPE
cesChanStatusBitMap	OBJECT-TYPE
cesCnfChanNum	OBJECT-TYPE
cesPortDs0ConfigBitMap	OBJECT-TYPE
cesPortNum	OBJECT-TYPE
chanConnType	OBJECT-TYPE
chanNum	OBJECT-TYPE
chanOAMstatus128	OBJECT-TYPE
chanOAMstatus160	OBJECT-TYPE
chanOAMstatus192	OBJECT-TYPE
chanOAMstatus224	OBJECT-TYPE
chanOAMstatus256	OBJECT-TYPE
chanOAMstatus32	OBJECT-TYPE
chanOAMstatus64	OBJECT-TYPE
chanOAMstatus96	OBJECT-TYPE
chanPacketNumber	OBJECT-TYPE
chanRowStatus	OBJECT-TYPE
chanStatusBitMap	OBJECT-TYPE
chanVci	OBJECT-TYPE
chanVpi	OBJECT-TYPE
currentClock	OBJECT-TYPE
currentClockSource	OBJECT-TYPE
dLCI	OBJECT-TYPE
diagResult	OBJECT-TYPE
diagTestId	OBJECT-TYPE
diagType	OBJECT-TYPE
imaObsDiffDelay	OBJECT-TYPE
imaPortNum	OBJECT-TYPE
imaPortState	OBJECT-TYPE
imaStatePortNum	OBJECT-TYPE
imatmDsx3SingleBitErrCorrEnable	OBJECT-TYPE
imatmdsx3PortIndex
listLinksPresentInImaGroup	OBJECT-TYPE
listOfLinksInImaGrp	OBJECT-TYPE
networkCacConfigState	OBJECT-TYPE
parConnAdminStatus	OBJECT-TYPE
parConnLocalPort	OBJECT-TYPE
parConnLocalSlot	OBJECT-TYPE
parConnLocalVcIndx	OBJECT-TYPE
parConnLocalVci	OBJECT-TYPE
parConnLocalVpi	OBJECT-TYPE
parConnRemoteNodeName	OBJECT-TYPE
parConnRemotePort	OBJECT-TYPE
parConnRemoteSlot	OBJECT-TYPE
parConnRemoteVci	OBJECT-TYPE
parConnRemoteVpi	OBJECT-TYPE
parIfLogicalInterface	OBJECT-TYPE
parSnNodeAlarmStatus	OBJECT-TYPE
parSnNodeIP	OBJECT-TYPE
parSnNodeId	OBJECT-TYPE
parSnNodeName	OBJECT-TYPE
parTrkAlarmStatus	OBJECT-TYPE
parTrkAlarmType	OBJECT-TYPE
parTrkCnfgCcRestrict	OBJECT-TYPE
parTrkCnfgDerouteDelay	OBJECT-TYPE
parTrkCnfgLineType	OBJECT-TYPE
parTrkCnfgPassSync	OBJECT-TYPE
parTrkCnfgRoutingCost	OBJECT-TYPE
parTrkCnfgTrafficClassAbr	OBJECT-TYPE
parTrkCnfgTrafficClassCbr	OBJECT-TYPE
parTrkCnfgTrafficClassFr	OBJECT-TYPE
parTrkCnfgTrafficClassFst	OBJECT-TYPE
parTrkCnfgTrafficClassNts	OBJECT-TYPE
parTrkCnfgTrafficClassTs	OBJECT-TYPE
parTrkCnfgTrafficClassVbr	OBJECT-TYPE
parTrkCnfgTrafficClassVoice	OBJECT-TYPE
parTrkId	OBJECT-TYPE
parTrkLocalPortNumber	OBJECT-TYPE
parTrkLocalSlotNumber	OBJECT-TYPE
parTrkLocalVTrunkId	OBJECT-TYPE
parTrkRemoteNodeIP	OBJECT-TYPE
parTrkRemoteNodeId	OBJECT-TYPE
parTrkRemoteNodeName	OBJECT-TYPE
parTrkRemoteNodeType	OBJECT-TYPE
parTrkRemotePortNumber	OBJECT-TYPE
parTrkRemoteSlotNumber	OBJECT-TYPE
parTrkRemoteTrunkId	OBJECT-TYPE
parTrkRemoteVTrunkId	OBJECT-TYPE
parTrkStatReserve	OBJECT-TYPE
portDs0ConfigBitMap	OBJECT-TYPE
portEgrPercentUtil	OBJECT-TYPE
portIngrPercentUtil	OBJECT-TYPE
portNum	OBJECT-TYPE
portOversubscribed	OBJECT-TYPE
portSignallingState	OBJECT-TYPE
portState	OBJECT-TYPE
primaryClockSource	OBJECT-TYPE
pxmClkErrReason	OBJECT-TYPE
pxmClkStratumLevel	OBJECT-TYPE
pxmCurrentClock	OBJECT-TYPE
pxmExtClk2ConnectorType	OBJECT-TYPE
pxmExtClk2SrcImpedance	OBJECT-TYPE
pxmExtClkConnectorType	OBJECT-TYPE
pxmExtClkSrcImpedance	OBJECT-TYPE
pxmExtClock2Present	OBJECT-TYPE
pxmExtClockPresent	OBJECT-TYPE
pxmPreviousClock	OBJECT-TYPE
pxmPrimaryInbandClockSourceLineNumber	OBJECT-TYPE
pxmPrimaryMuxClockSource	OBJECT-TYPE
pxmPrimarySMClockSourceSlotNumber	OBJECT-TYPE
pxmSecondaryInbandClockSourceLineNumber	OBJECT-TYPE
pxmSecondaryMuxClockSource	OBJECT-TYPE
pxmSecondarySMClockSourceSlotNumber	OBJECT-TYPE
rpmChanInterface	OBJECT-TYPE
rpmChanNum	OBJECT-TYPE
rpmChanVci	OBJECT-TYPE
rpmChanVpi	OBJECT-TYPE
rpmPortInterface	OBJECT-TYPE
rpmPortSubInterface	OBJECT-TYPE
secondaryClockSource	OBJECT-TYPE
srmStartT1LineNum	OBJECT-TYPE
srmT3LineNum	OBJECT-TYPE
srmTargetSlotLineNum	OBJECT-TYPE
srmTargetSlotNum	OBJECT-TYPE
srmeLineNum	OBJECT-TYPE
srmeStartVtNum	OBJECT-TYPE
srmeTargetSlotLineNum	OBJECT-TYPE
srmeTargetSlotNum	OBJECT-TYPE
srmeVtFramingType	OBJECT-TYPE
vismAal2CidFailReason	OBJECT-TYPE
vismAal2CidLcn	OBJECT-TYPE
vismAal2CidNum	OBJECT-TYPE
vismAal2CidState	OBJECT-TYPE
vismAal2SubcellMuxing	OBJECT-TYPE
vismAppliedTemplate	OBJECT-TYPE
vismCasFileName	OBJECT-TYPE
vismCasVariantName	OBJECT-TYPE
vismCasVariantState	OBJECT-TYPE
vismChanActivityState	OBJECT-TYPE
vismChanLockingState	OBJECT-TYPE
vismChanNum	OBJECT-TYPE
vismChanPortNum	OBJECT-TYPE
vismChanReroute	OBJECT-TYPE
vismChanRowStatus	OBJECT-TYPE
vismChanStatusBitMap	OBJECT-TYPE
vismCnfChanNum	OBJECT-TYPE
vismConfigChangeTypeBitMap	OBJECT-TYPE
vismFeatureBitMap	OBJECT-TYPE
vismHdlcChanNum	OBJECT-TYPE
vismIpAddress	OBJECT-TYPE
vismMode	OBJECT-TYPE
vismPortDs0ConfigBitMap	OBJECT-TYPE
vismPortNum	OBJECT-TYPE
vismPortState	OBJECT-TYPE
vismPortType	OBJECT-TYPE
vismTrapIntIndex1	OBJECT-TYPE
vismTrapIntIndex2	OBJECT-TYPE
vismTrapStrIndex1	OBJECT-TYPE
x21LineAlarmState	OBJECT-TYPE
x21LineNum	OBJECT-TYPE
x21LineType	OBJECT-TYPE
x21portNum	OBJECT-TYPE

From GENERICOBJECT-MIB

genericLineNum	OBJECT-TYPE
genericLineType	OBJECT-TYPE
genericTimeStamp	OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RTM-MIB

lastSequenceNumber

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Description
NTF coreCardSwitchTrap	1.3.6.1.4.1.351.110.0.50000	The standby cards have become active, due to the failure of the active cards. The log in the card, shows the reason the cards are ASC and BNM.
NTF shelRestartTrap	1.3.6.1.4.1.351.110.0.50001	Shelf restart with reset reason
NTF functionModuleRemovedTrap	1.3.6.1.4.1.351.110.0.50002	Indicates that a function module has been removed. This includes SRM removal.
NTF functionModuleInsertedTrap	1.3.6.1.4.1.351.110.0.50003	Indicates that a function module has been inserted. This includes SRM insertion.
NTF functionModuleSwitchoverTrap	1.3.6.1.4.1.351.110.0.50004	Indicates that a function module has changed state from standby to active or vice versa
NTF functionModuleActiveTrap	1.3.6.1.4.1.351.110.0.50005	Indicates that a function module is operational
NTF functionModuleFailedTrap	1.3.6.1.4.1.351.110.0.50006	Indicates that a function module is inoperational
NTF functionModuleMismatchTrap	1.3.6.1.4.1.351.110.0.50007	Informational alarm generated due to a) different front card inserted b) same front card with a different feature list is inserted
NTF functionModuleSlefTestFailedTrap	1.3.6.1.4.1.351.110.0.50008	Indicates that a function module self test failed. Not generated when self test passes
NTF functionModuleStandbyTrap	1.3.6.1.4.1.351.110.0.50009	Indicates that a function module is in standby state
NTF bnmTemperatureNormalTrap	1.3.6.1.4.1.351.110.0.50010	Indicates the temperature is within the normal range
NTF bnmTemperatureAboveNormalTrap	1.3.6.1.4.1.351.110.0.50011	Indicates the temperature has exceeded the upper limit of its normal range
NTF bnmDclevelNormalTrap	1.3.6.1.4.1.351.110.0.50012	Indicates that the shelf is within its normal DC level
NTF bnmDclevelBelowNormalTrap	1.3.6.1.4.1.351.110.0.50013	Indicates that the shelf is DC level below the normal DC level
NTF bnmPowersupplyNormalTrap	1.3.6.1.4.1.351.110.0.50014	Indicates the shelfs power supply status is normal
NTF bnmPowersupplyFailedTrap	1.3.6.1.4.1.351.110.0.50015	Indicates the shelfs power supply status has Failed
NTF bnmFanrpmNormalTrap	1.3.6.1.4.1.351.110.0.50016	Indicates that a particular fan's RPM Normal
NTF bnmFanrpmBelowNormalTrap	1.3.6.1.4.1.351.110.0.50017	Indicates that a particular fan's RPM below Normal
NTF shelfIntegratedAlarmTrap	1.3.6.1.4.1.351.110.0.50018	Indicates that the shelf integrated alarm status is changed and sends the status of the shelf integrated alarm. The shelfFilteredAlarm contains the alarm status of a filtered subset of all node alarms.
NTF userLoginTrap	1.3.6.1.4.1.351.110.0.50020	Indicates that a user logged in
NTF userLogoutTrap	1.3.6.1.4.1.351.110.0.50021	Indicates that a user logout
NTF shelfLossLmiAlarmTrap	1.3.6.1.4.1.351.110.0.50022	Indicates the Loss of LMI Alarm for AXIS BNM trunk. (ANNEX G signalling failure)
NTF shelfLossLmiAlarmClearTrap	1.3.6.1.4.1.351.110.0.50023	Indicates the Clear of Loss of LMI Alarm for AXIS BNM trunk. (ANNEX G signalling failure has cleared)
NTF shelfPowerOverLoadTrap	1.3.6.1.4.1.351.110.0.50024	Indicates that the functionModuleType when inserted raised the total power consumption of the shelf beyond threshold value. functionModuleType value other(1) indicates that a fan tray has been removed, which increases the power consumption value beyond the capacity of remaining fan tray. shelfIntegeratedAlarm is set to the value major(3). When the alarm condition is cleared, the same trap is sent with shelfIntegratedAlarm value set to clear (1)
NTF lineModuleRemovedTrap	1.3.6.1.4.1.351.110.0.50030	Indicates whether or not a particular line line module has been removed
NTF lineModuleInsertedTrap	1.3.6.1.4.1.351.110.0.50031	Indicates whether or not a particular line line module has been inserted
NTF lineModuleMismatchTrap	1.3.6.1.4.1.351.110.0.50032	Indicates that the front card does not support the line module.
NTF cardResPartTypeChangeTrap	1.3.6.1.4.1.351.110.0.50033	This trap is sent out when the resource partition type is changed. The possible changes for cardLcnPartitionType are: 1: no partition, 2: controller based, 3: port controller based
NTF secLineModuleRemovedTrap	1.3.6.1.4.1.351.110.0.50035	Indicates whether or not a particular secondary (bottom) line module has been removed. This is applicable to MGX only, in a case where the front card(functionModuleType) is a full height card with 2 half height back cards.
NTF secLineModuleInsertedTrap	1.3.6.1.4.1.351.110.0.50036	Indicates whether or not a particular secondary (bottom) line module has been inserted This is applicable to MGX only, in a case where the front card(functionModuleType) is a full height card with 2 half height back cards.
NTF secLineModuleMismatchTrap	1.3.6.1.4.1.351.110.0.50037	Indicates that the front card does not support the secondary (bottom)line module. This is applicable to MGX only, in a case where the front card(functionModuleType) is a full height card with 2 half height back cards.
NTF coreCardsConfigMismatchTrap	1.3.6.1.4.1.351.110.0.50040	Mismatch between the core card configuration and the physical core cards in the system, e.g., if ASC card has configuration for a BNM-T3 card but a BNM-E3 card is plugged in.
NTF coreCardsPeerMismatchTrap	1.3.6.1.4.1.351.110.0.50041	Mismatch between two core card sets, e.g., one set has BNM-T3 but another set has BNM-E3.
NTF coreCardsConfigClearTrap	1.3.6.1.4.1.351.110.0.50042	Sent when the config is cleared.
NTF functionModuleHoldTrap	1.3.6.1.4.1.351.110.0.50044	Indicates that a function module is in Hold state
NTF redActiveatedTrap	1.3.6.1.4.1.351.110.0.50045	Sent when the redundant card goes active
NTF redRevertedTrap	1.3.6.1.4.1.351.110.0.50046	Sent when the redundant card is reverted back to standby (reset first)
NTF redAddedTrap	1.3.6.1.4.1.351.110.0.50047	Sent when the redundancy is added
NTF redDeletedTrap	1.3.6.1.4.1.351.110.0.50048	Sent when the redundansy is deleted
NTF bnmCurclksourceTrap	1.3.6.1.4.1.351.110.0.50050	Indicates that the current clock source has changed
NTF bnmTrunkCellFormatTrapnum	1.3.6.1.4.1.351.110.0.50051	This trap is sent out when the trunk cell format is changed. When a BNM-155 card is present it can be changed between UNI and NNI when there are no connections on the shelf. This is fixed for a T3/E3 card to STI format.
NTF atmLineCellFormatTrap	1.3.6.1.4.1.351.110.0.50052	This trap is sent out when the line cell format is changed. PXM lines can be configured to either UNI or NNI cell formats. STI format is not supported in MGX PXM.
NTF diagStatusTrap	1.3.6.1.4.1.351.110.0.50053	This trap is sent out to report the results of the Diagnostics performed on the shelf. The diagtype varbind indicates whether this is the results of Power On Self Test (POST) or Online Diagnostics. For POST, this trap is sent only when POST fails and the diagTestId varbind specifies the test number of the first test that failed. For Online Diagnostics, this trap is sent whenever a diagnostics test configured as part of online diagnostics fails or passes. The traps is sent when the results of a diagnostic test changes from passed to failed or changes from failed to passed. The diagResult varbind specifies passed/failed and the diagTestId varbind specifies the test that failed.
NTF trapBERTStart	1.3.6.1.4.1.351.110.0.50060	Sent when BERT is configured and started.
NTF trapBERTEnd	1.3.6.1.4.1.351.110.0.50061	Sent when the ongoing BERT is stopped.
NTF trapBERTAbort	1.3.6.1.4.1.351.110.0.50062	This is sent out when ongoing BERT is aborted due to state changes of the cards that BERT involves namely ASC, SRM and SM. The test will be aborted when there is a core card switch or a SM switch to redundant card also.
NTF coreCardSwitchInProgress	1.3.6.1.4.1.351.110.0.50064	This indicates that the switchcc process is in progress, that all the initial checks for switchcc to happen were successful.
NTF coreCardSwitchBlocked	1.3.6.1.4.1.351.110.0.50065	This indicates that the switchcc process cannot happen due to the checks failing. Hence a switchcc blocked trap is being sent . more like a failure trap
NTF bnmNolinealarmTrapnum	1.3.6.1.4.1.351.110.0.50100	Indicates no line alarm, obsoleted from AXIS4.0
NTF bnmlinealarmTrapnum	1.3.6.1.4.1.351.110.0.50101	Indicates line alarm exists, obsoleted from AXIS4.0 0x01 rcvRAIstate 0x02 xmtRAIstate 0x04 rcvAISstate 0x08 xmtAISstate 0x10 rcvOOFstate 0x20 rcvLOSstate
NTF bnmLineLpbkEnableTrapnum	1.3.6.1.4.1.351.110.0.50102	Indicates that line loopback has been enabled, obsoleted from AXIS4.0
NTF bnmLineLpbkDisableTrapnum	1.3.6.1.4.1.351.110.0.50103	Indicates that line loopback has been disabled, obsoleted from AXIS 4.0
NTF dsx3LineNoAlarmTrap	1.3.6.1.4.1.351.110.0.50104	Indicates no line alarm
NTF dsx3LineInAlarmTrap	1.3.6.1.4.1.351.110.0.50105
NTF dsx3LineLpbkEnableTrap	1.3.6.1.4.1.351.110.0.50106	Indicates that line loopback has been enabled
NTF dsx3LineLpbkDisableTrap	1.3.6.1.4.1.351.110.0.50107	Indicates that line loopback has been disabled.
NTF sonetLineInAlarmTrap	1.3.6.1.4.1.351.110.0.50108	Indicates line alarm exists. Note that the value sent in cwSonetLineCurrentStatus in this trap contains information for all the three sonet layers (section, line, path) and also the loopback state. So it doesn't match the description provided for the cwSonetLineCurrentStatus object under `cwSonetLineCurrentTable'. The various bits in cwSonetLineCurrentStatus are: bit 1 sonetLineRcvRAI bit 2 sonetLineXmtRAI bit 3 sonetLineRcvAIS bit 4 sonetLineXmtAIS bit 5 sonetSectionRcvOOF bit 6 sonetSectionRcvLOS bit 7 localLoopBack bit 8 remoteLoopBack bit 9 remotePayloadLoopBack bit 10 sonetPathRcvLOCD bit 11 sonetPathRcvLOP bit 12 sonetPathRcvAis bit 13 sonetPathXmtAis bit 14 sonetPathRcvRdi bit 15 sonetPathXmtRdi
NTF sonetLineNoAlarmTrap	1.3.6.1.4.1.351.110.0.50109	Indicates line alarm has cleared Please refer to sonetLineInAlarmTrap for the format of cwSonetLineCurrentStatus
NTF sonetLineLpbkEnableTrapnum	1.3.6.1.4.1.351.110.0.50110	Indicates that line loopback has been enabled Please refer to sonetLineInAlarmTrap for the format of cwSonetLineCurrentStatus
NTF sonetLineLpbkDisableTrapnum	1.3.6.1.4.1.351.110.0.50111	Indicates that line loopback has been disabled. Please refer to sonetLineInAlarmTrap for the format of cwSonetLineCurrentStatus
NTF sonetXmtClkSrcChangeTrap	1.3.6.1.4.1.351.110.0.50112	Indicates the transmit clock source changed
NTF sonetXmtClkSrcLossTrap	1.3.6.1.4.1.351.110.0.50113	Indicates that the transmit clock source is lost and a new clock source is in effect.
NTF dsx1LineNoAlarmTrap	1.3.6.1.4.1.351.110.0.50120	Indicates no line alarm
NTF dsx1LineInAlarmTrap	1.3.6.1.4.1.351.110.0.50121	Indicates line alarm exists 0x01 rcvRAIstate 0x02 xmtRAIstate 0x04 rcvAISstate 0x08 xmtAISstate 0x10 rcvOOFstate 0x20 rcvLOSstate
NTF dsx1LineLpbkEnableTrap	1.3.6.1.4.1.351.110.0.50122	Indicates that line loopback has been enabled
NTF dsx1LineLpbkDisableTrap	1.3.6.1.4.1.351.110.0.50123	Indicates that line loopback has been disabled.
NTF dsx1StatLineAlarmTrap	1.3.6.1.4.1.351.110.0.50130	Indicates the current statistical alarm State
NTF dsx3StatLineAlarmTrap	1.3.6.1.4.1.351.110.0.50131	Indicates the current statistical alarm State
NTF bnmStatSonetSectionalmTrapnum	1.3.6.1.4.1.351.110.0.50132	Indicates the current sonet section statistical alarm State
NTF bnmStatSonetLinealmTrapnum	1.3.6.1.4.1.351.110.0.50133	Indicates the current sonet Line statistical alarm State
NTF bnmStatSonetPathalmTrapnum	1.3.6.1.4.1.351.110.0.50134	Indicates the current sonet Path statistical alarm State
NTF pxmCurClkSourceTrap	1.3.6.1.4.1.351.110.0.50135	Indicates that the current clock source has changed
NTF srm3t3Xmtclksource	1.3.6.1.4.1.351.110.0.50140	Indicates that the current clock source has been changed.
NTF srm3t3LineEnable	1.3.6.1.4.1.351.110.0.50141	Indicates that one T3 line has been enabled.
NTF srm3t3LineDisable	1.3.6.1.4.1.351.110.0.50142	Indicates that one T3 line has been disabled.
NTF srm3t3FELineLpbkEnable	1.3.6.1.4.1.351.110.0.50143	Indicates which DS1 or DS3 has been set in the loopback testing.
NTF srm3t3LineLpbkDisable	1.3.6.1.4.1.351.110.0.50144	Indicates which DS1 or DS3 has been reset from the loopback testing.
NTF srm3t3AddLink	1.3.6.1.4.1.351.110.0.50145	Indicates which T1 line from a T3 is added to which slot and which line.
NTF srm3t3DelLink	1.3.6.1.4.1.351.110.0.50146	Indicates which T1 line from a T3 is deleted from which slot and which line.
NTF srm3t3DelSlotLink	1.3.6.1.4.1.351.110.0.50147	Indicates which line is deleted from a slot
NTF srm3t3NELineLpbkEnable	1.3.6.1.4.1.351.110.0.50148	Indicates which DS1 or DS3 at the near end has been set for the loopback testing.
NTF srm3t3NELineLpbkDisable	1.3.6.1.4.1.351.110.0.50149	Indicates which DS1 or DS3 at the near end has been removed from the loopback testing.
NTF srmLossOfClockTrap	1.3.6.1.4.1.351.110.0.50150	Indicates a SRM T3 line lost clock source.
NTF srmeAddLink	1.3.6.1.4.1.351.110.0.50161	Indicates which Vt from a SRME Line is added to which slot and which line.
NTF srmeDelLink	1.3.6.1.4.1.351.110.0.50162	Indicates which Vt from SRME Line is deleted from which slot and which line.
NTF srmeDelSlotLink	1.3.6.1.4.1.351.110.0.50163	Indicates which line is deleted from a slot
NTF srmeCnfLink	1.3.6.1.4.1.351.110.0.50164	Indicates which Vt in which framing type is changed.
NTF trapRpmPortAdd	1.3.6.1.4.1.351.110.0.50191	Indicates that a sub interface is added.
NTF trapRpmPortDelete	1.3.6.1.4.1.351.110.0.50192	Indicates that a sub interface is deleted.
NTF trapRpmPortModify	1.3.6.1.4.1.351.110.0.50193	Indicates that a sub interface is modified.
NTF trapRpmPortActive	1.3.6.1.4.1.351.110.0.50194	Indicates that a sub interface is Active.
NTF trapRpmChanAdd	1.3.6.1.4.1.351.110.0.50196	Indicates that a rpm channel is added.
NTF trapRpmChanDelete	1.3.6.1.4.1.351.110.0.50197	Indicates that a rpm channel is deleted.
NTF trapRpmChanModify	1.3.6.1.4.1.351.110.0.50198	Indicates that a rpm channel is modified.
NTF trapRpmChanActive	1.3.6.1.4.1.351.110.0.50199	Indicates that a rpm channel is Active.
NTF x21LineNoAlarmTrap	1.3.6.1.4.1.351.110.0.50200	Indicates no line alarm
NTF x21LineInAlarmTrap	1.3.6.1.4.1.351.110.0.50201	Indicates line alarm exists
NTF x21LineLpbkEnableTrap	1.3.6.1.4.1.351.110.0.50202	Indicates that line loopback has been enabled
NTF x21LineLpbkDisableTrap	1.3.6.1.4.1.351.110.0.50203	Indicates that line loopback has been disabled.
NTF x21LineLpbkDetectedTrap	1.3.6.1.4.1.351.110.0.50204	Indicates that line loopback code/condition detected.
NTF x21LineLpbkRemovedTrap	1.3.6.1.4.1.351.110.0.50205	Indicates that line loopback code/condition does not exist any more.
NTF trapImaDisabled	1.3.6.1.4.1.351.110.0.50230	Indicates that IMA group is disabled
NTF trapImaActive	1.3.6.1.4.1.351.110.0.50231	Indicates that IMA group is Configured
NTF trapImaBandwidthChanged	1.3.6.1.4.1.351.110.0.50232	Indicates that the bandwidth of an IMA group changed due to addition/deletion of links to/from the IMA group. This trap is Obsolete for MGX8850.
NTF trapImaFailedAcpTimeout	1.3.6.1.4.1.351.110.0.50233	Indicates that the IMA group was brought down due to ACP cells not being received within the expected interval. This trap is Obsolete for MGX8850.
NTF trapImaFailedMajorAlm	1.3.6.1.4.1.351.110.0.50234	Indicates that the IMA group failed due to major alarm on the IMA group This trap is Obsolete for MGX8850.
NTF trapImaFailedSigFailure	1.3.6.1.4.1.351.110.0.50235	Indicates that the IMA group failed due to an IMA signalling failure (eg: ACP cells are being received but the expected ones are not being received or an unexpected change in IMA-ID/LID on a link occurred etc This trap is Obsolete for MGX8850.
NTF trapImaFailedBadDiffDelay	1.3.6.1.4.1.351.110.0.50236	Indicates that the IMA group failed due to differential delay exceeding the maximum permissible for this IMA group. The variable 'imaObsDiffDelay' gives the current observed differential delay for this IMA group This trap is Obsolete for MGX8850.
NTF trapImaRcvAisLoam	1.3.6.1.4.1.351.110.0.50237	Indicates that the IMA is receiving a local OAM cell AIS from the remote end This trap is Obsolete for MGX8850.
NTF trapImaRcvRdiLoam	1.3.6.1.4.1.351.110.0.50238	Indicates that the IMA is receiving a local OAM cell RDI from the remote end This trap is Obsolete for MGX8850.
NTF trapImaFailedOtherReason	1.3.6.1.4.1.351.110.0.50239	Indicates that the IMA group failed due to a non- IMA protocol related failure. The value of imaPortState will denote the reason for failure.
NTF trapImatmClockChange	1.3.6.1.4.1.351.110.0.50240	Indicates that the current clock source changed from primary to secondary
NTF trapImatmBadClockSource	1.3.6.1.4.1.351.110.0.50241	Indicates that no good clock source is available
NTF trapImaLinkStateChange	1.3.6.1.4.1.351.110.0.50244	Indicates that the link in an IMA group is in LIF LODS or No Failure.
NTF trapImaLinkInLoopback	1.3.6.1.4.1.351.110.0.50245	Indicates that IMA Line Alarm exists. Can be lineLcpErr lineNotInLDS lineInLoopback
NTF trapImatmDsx3HecChange	1.3.6.1.4.1.351.110.0.50246	Indicate that the HEC Error Correction Option for DSX3 has changed. Can be Enable or Disable.
NTF trapImaGTSMchange	1.3.6.1.4.1.351.110.0.50250	Indicate the failure status of the IMA group(GTSM goes UP/DOWN)
NTF trapImaCellRateChange	1.3.6.1.4.1.351.110.0.50251	Indicates that the bandwidth of an IMA group changed due to addition/deletion of links to/from the IMA group
NTF bnmPlcpAlmActiveTrap	1.3.6.1.4.1.351.110.0.50300	Indicates that no PLCP alarm exists
NTF bnmPlcpAlmFailedTrap	1.3.6.1.4.1.351.110.0.50301	Indicates that PLCP alarm exists
NTF bnmPlcpStatalmTrap	1.3.6.1.4.1.351.110.0.50303	PLCP Statistical alarm state change
NTF bnmPlcpLpbkEnableTrap	1.3.6.1.4.1.351.110.0.50304	Loopback Enable trap
NTF bnmPlcpLpbkDisableTrap	1.3.6.1.4.1.351.110.0.50305	Loopback Disable trap
NTF trapChanOamLpbkStatus	1.3.6.1.4.1.351.110.0.50311	Sent when the chan Ras_Oam_Loopback_state changes from Failed to Ok or Ok to Failed. It will carry status for a chunk of 256 channels as bitmaps. If the status of only 1 channel belonging to the chunk of 256 changes, trap is sent only for that chunk of 256 channels and not for any other chunk. For eg., suppose if channel 500 fails ras loopback test, trap is sent for the second chunk of 256 channels spanning channel nos 257 to 512.
NTF rasDskChksumStatusTrap	1.3.6.1.4.1.351.110.0.50312	Indicates the Status of the SM configuration and FirmWare files. The Trap shows the number of corrupted PRI and Firmware files in the ASC from where it is sent. This Trap is sent everytime the diagnostics is completed.
NTF rasDskBadSectorsTrap	1.3.6.1.4.1.351.110.0.50313	Indicates the number of Bad Sectors in the ASC Hard Disk. If the number of Bad Sectors exceeds the threshold value, the rasDskHealth is set to FAIL. The threshold value is 30% of the total number of Sectors. This Trap is sent everytime the diagnostics is completed.
NTF trapChanStatusSummary	1.3.6.1.4.1.351.110.0.50314	Sent when there are multiple channel failures and the total number of traps in 1 min exceeds the card level set thresholds. This trap is common to all the NBSM cards. viz. FRSM-8T1E1, CESM-8T1E1, AUSM-8T1E1, FRSM-VHS, CESM-T3E3 This traps informs the network management tool that the channel traps will not be sent from now but only summary traps will be sent at every 1 minute till the condition that is causing so many traps in quick succession goes away. This trap is not applicable to MGX Release 1.x.
NTF trapConfigChangeRev2	1.3.6.1.4.1.351.110.0.50315	Sent when the config has changed. The bit map indicates the change in card, line, port, channel, egress-q or resource partition configuration. The configChangeObjectIndex object shows the the line, port, channel, egress-q or resource partition index. The configChangeParentObjectIndex object shows the parent (higher level) index of configChangeObjectIndex. The configChangeGrandParentObjectIndex object shows the parent (higher level) index of configChangeParentObjectIndex. The configChangeStatus shows the operation type which can be add, mod or del. The configChangeSMSpecificObject is a generic object and based on the requirement can be used differently in each card type. The usage of the same is listed below. This trap is not applicable to MGX-8850 Release 1.x.x and MGX-8220
NTF trapLineEnabled	1.3.6.1.4.1.351.110.0.50350	indicates line enabled. Applicable to AUSM and all FRSM cards except HS1 HS2 HS2B.
NTF trapCardOvrSubscribed	1.3.6.1.4.1.351.110.0.50380	The card is over-subscribed
NTF trapGenFrPortActive	1.3.6.1.4.1.351.110.0.50381	Trap that is generated to indicate that a FR logical port has become active. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/ HS2).
NTF trapGenFrPortFailed	1.3.6.1.4.1.351.110.0.50382	Trap that is generated to indicate that a FR logical port has failed. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrPortDelete	1.3.6.1.4.1.351.110.0.50383	Trap that is generated to indicate that a FR logical port has become deleted. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/ HS2).
NTF trapGenFrPortLoopbackEnabled	1.3.6.1.4.1.351.110.0.50384	Trap that is generated to indicate that loopback on a FR logical port has become active. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrPortLoopbackDisabled	1.3.6.1.4.1.351.110.0.50385	Trap that is generated to indicate that loopback on a FR logical port has become disabled. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrPortOvrSubscribed	1.3.6.1.4.1.351.110.0.50386	Trap that is generated to indicate that a FR logical port has become oversubscribed. Currently, this trap is used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrChanActive	1.3.6.1.4.1.351.110.0.50387	Sent when an FR logical channel becomes active: this trap is currently used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrChanFailed	1.3.6.1.4.1.351.110.0.50388	Sent when an FR logical channel fails: this trap is currently used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrChanDelete	1.3.6.1.4.1.351.110.0.50389	Sent when an FR logical channel is deleted: this trap is currently used only in all flavours of FRSM-VHS card (FRSM-2CT3/T3/E3/HS2).
NTF trapGenFrsmConDown	1.3.6.1.4.1.351.110.0.50390	Sent when a FRSM Channel is brought down. This trap is not applicable to MGX Release 1.x.
NTF trapGenFrsmConUp	1.3.6.1.4.1.351.110.0.50391	Sent when a FRSM Channel is brought up from down. The previous RowStatus of this channel must be outOfService. This trap is not applicable to MGX Release 1.x.
NTF trapGenFrsmChanReroute	1.3.6.1.4.1.351.110.0.50392	Sent when a FRSM Channel is rerouted. This trap is not applicable to MGX Release 1.x.
NTF trapGenFrChannelAlarm	1.3.6.1.4.1.351.110.0.50393	Sent when an FR logical channel is in Alarm, i.e. the channel can pass traffic within the PNNI n/w but is in Alarm because of CPE connectivity, or the line being in alarm. This trap is used for all FRSM flavors. This trap is not applicable to MGX Release 1.x.
NTF trapGenFrChannelFailed	1.3.6.1.4.1.351.110.0.50394	Sent when an FR logical channel fails, i.e. the channel cannot pass traffic within the PNNI n/w. This trap is used for all FRSM flavors. This trap is not applicable to MGX Release 1.x.
NTF trapPortActive	1.3.6.1.4.1.351.110.0.50400	indicates port active
NTF trapPortFailed	1.3.6.1.4.1.351.110.0.50401	The port fails
NTF trapPortDelete	1.3.6.1.4.1.351.110.0.50402	The port is deleted
NTF trapPortLoopbackEnabled	1.3.6.1.4.1.351.110.0.50403	The port loopback is enabled
NTF trapPortLoopbackDisabled	1.3.6.1.4.1.351.110.0.50404	The port loopback is disabled
NTF trapPortAdded	1.3.6.1.4.1.351.110.0.50405	indicates port added, currently this trap is not used
NTF trapPortOvrSubscribed	1.3.6.1.4.1.351.110.0.50406	The port is over-subscribed
NTF trapX21PortActive	1.3.6.1.4.1.351.110.0.50450	indicates port active
NTF trapX21PortFailed	1.3.6.1.4.1.351.110.0.50451	The port fails
NTF trapX21PortDelete	1.3.6.1.4.1.351.110.0.50452	The port is deleted
NTF trapX21PortLoopbackEnabled	1.3.6.1.4.1.351.110.0.50453	The port loopback is enabled
NTF trapX21PortLoopbackDisabled	1.3.6.1.4.1.351.110.0.50454	The port loopback is disabled
NTF trapX21PortAdded	1.3.6.1.4.1.351.110.0.50455	indicates port added
NTF trapChanActive	1.3.6.1.4.1.351.110.0.50500	Sent when the chan is active
NTF trapChanFailed	1.3.6.1.4.1.351.110.0.50501	Sent when the chan is failed
NTF trapChanDelete	1.3.6.1.4.1.351.110.0.50502	Sent when the chan is deleted
NTF trapChanAdded	1.3.6.1.4.1.351.110.0.50503	Sent when the chan is added, currently this trap is not used
NTF egressDataBuffersOverflowTrap	1.3.6.1.4.1.351.110.0.50505	Sent when the Egress Data Buffers are not available.
NTF egressDataBuffersNormalTrap	1.3.6.1.4.1.351.110.0.50506	Sent when the Egress Data Buffers are available.
NTF trapConfigChange	1.3.6.1.4.1.351.110.0.50600	Sent when the config has changed. The bit map tells if the change on line/port/channel and the object index shows the line#/port#/channel#, the status shows if it's an add or mod or del.
NTF pxmApsDeactivateTrap	1.3.6.1.4.1.351.110.0.50603	This trap indicates APS feature is deactivated for the working and protection pair. Severity = Clear NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsActivateTrap	1.3.6.1.4.1.351.110.0.50604	This trap indicates APS feature is Activated for the working and protection pair. Severity = Clear NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsCardFailureTrap	1.3.6.1.4.1.351.110.0.50605	This trap indicates abnormal condition on a PSM card which is used for APS feature. Severity = Major NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsLineFailureTrap	1.3.6.1.4.1.351.110.0.50606	This trap indicates abnormal condition occurs on the working SONET line in the APS pair. Severity = Major NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsLineSwitchTrap	1.3.6.1.4.1.351.110.0.50607	This trap indicates the APS line has been switched. The apsLineSwReason describes the switch reason. Severity = Minor NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsLineSwitchFailureTrap	1.3.6.1.4.1.351.110.0.50608	This trap indicates abnormal condition occurs during the APS switch event. The apsLineSwFailureCode describes the failure reason. Severity = Major NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsStandbyLineFailureTrap	1.3.6.1.4.1.351.110.0.50609	This trap indicates abnormal condition occurs on the protection SONET line in the APS pair. The apsLineFailureCode describes the failure reason. Severity = Major NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsCardClearTrap	1.3.6.1.4.1.351.110.0.50610	This trap indicates abnormal condition on one of the PXM cards in this APS pair is cleared. Severity = Clear NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsLineClearTrap	1.3.6.1.4.1.351.110.0.50611	This trap indicates abnormal condition on the working SONET line is cleared. Severity = Clear NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsStandbyLineClearTrap	1.3.6.1.4.1.351.110.0.50612	This trap indicates abnormal condition on the standby SONET line is clear. Severity = Clear NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsConfigChangeTrap	1.3.6.1.4.1.351.110.0.50613	This trap indicates sonet APS configuration changed
NTF pxmApsModeMismatchTrap	1.3.6.1.4.1.351.110.0.50614	This trap indicates that sonet APS architecture mode on the two ends of the APS pair is different. This mismatch will no cause a mode switch from 1+1 on the near end. Far end, if capable, may change its mode. If far end is not capable, manual intervention will be required. NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF pxmApsModeMismatchClearTrap	1.3.6.1.4.1.351.110.0.50615	This trap indicates sonet APS architecture mode mismatch is cleared. NOTE: it is used by SRME too and the moduleSlotNumber will identify the source from PXM or SRME
NTF trapVismIpAddressChanged	1.3.6.1.4.1.351.110.0.50700	Sent when the VISM card's IP address is changed.
NTF trapVismChanActive	1.3.6.1.4.1.351.110.0.50709	Sent when a VISM Channel becomes active. genericLineNum is always set to 0 since it is not applicable to VISM.
NTF trapVismChanDeleted	1.3.6.1.4.1.351.110.0.50710	Sent when a VISM Channel is deleted genericLineNum is always set to 0 since it is not applicable to VISM.
NTF trapVismPortAdded	1.3.6.1.4.1.351.110.0.50711	Indicates port added.
NTF trapVismPortActive	1.3.6.1.4.1.351.110.0.50712	Indicates port active.
NTF trapVismPortFailed	1.3.6.1.4.1.351.110.0.50713	Indicates port Failed.
NTF trapProtectedChanActive	1.3.6.1.4.1.351.110.0.50714	Sent when vismChanActivityState transitions to active.
NTF trapProtectedChanStandby	1.3.6.1.4.1.351.110.0.50715	Sent when vismChanActivityState transitions to standby.
NTF trapProtectedChanFailed	1.3.6.1.4.1.351.110.0.50716	Sent when vismChanActivityState transitions to failed.
NTF trapProtectedChanLocked	1.3.6.1.4.1.351.110.0.50717	Sent when vismChanLockingState transitions to lock.
NTF trapProtectedChanUnlocked	1.3.6.1.4.1.351.110.0.50718	Sent when vismChanLockingState transitions to unlock.
NTF trapVismCasVariantAdded	1.3.6.1.4.1.351.110.0.50739	Indicates that an entry has been added to vismCasVarintTable.
NTF trapVismCasVariantDeleted	1.3.6.1.4.1.351.110.0.50740	Indicates that an entry has been deleted from vismCasVarintTable.
NTF trapVismCasVariantConfigured	1.3.6.1.4.1.351.110.0.50741	Indicates that casVariantState is transitioned to configured.
NTF trapVismCasVariantNotConfigured	1.3.6.1.4.1.351.110.0.50742	Indicates that casVariantState is transitioned to notConfigured.
NTF trapVismCodecTemplateChanged	1.3.6.1.4.1.351.110.0.50743	Indicates that the VISM Codec template has been changed.
NTF trapVismModeChanged	1.3.6.1.4.1.351.110.0.50744	Indicates that the vismMode has been changed on the card.
NTF trapVismScalarChange	1.3.6.1.4.1.351.110.0.50745	Sent when a scalar object/objects changes. The bit map indicates the group to which the changed object/objects belong. For a single SET operation, a single trap will be sent per group, regardless of how many objects got changed in in that group.
NTF trapVismTableChange	1.3.6.1.4.1.351.110.0.50746	Sent when a table config has changed. The bit map tells which table got changed. and vismTrapIntIndex1 shows the index of the table entry which got changed. If there are 2 index values, the 2nd index will be contained in vismTrapIntIndex2. If the table has a string index, the index value will be contained in vismTrapStrIndex1.
NTF trapVismAal2CidAdded	1.3.6.1.4.1.351.110.0.50747	Indicates that an entry has been added to the table vismAal2CidCnfTable.
NTF trapVismAal2CidDeleted	1.3.6.1.4.1.351.110.0.50748	Indicates that an entry has been deleted from the table vismAal2CidCnfTable.
NTF trapVismHdlcChanAdded	1.3.6.1.4.1.351.110.0.50752	Indicates that an entry has been added to the table vismHdlcChanTable.
NTF trapVismHdlcChanDeleted	1.3.6.1.4.1.351.110.0.50753	Indicates that an entry has been deleted from the table vismHdlcChanTable.
NTF trapVismPortDeleted	1.3.6.1.4.1.351.110.0.50754	Indicates port deleted.
NTF trapVismChanAdded	1.3.6.1.4.1.351.110.0.50755	Sent when a VISM Channel is added genericLineNum is always set to 0 since it is not applicable to VISM.
NTF trapVismChanFailed	1.3.6.1.4.1.351.110.0.50756	Sent when a VISM Channel fails genericLineNum is always set to 0 since it is not applicable to VISM.
NTF trapVismConDown	1.3.6.1.4.1.351.110.0.50757	Sent when a VISM Channel is brought down.
NTF trapVismConUp	1.3.6.1.4.1.351.110.0.50758	Sent when a VISM Channel is brought up from down. The previous RowStatus of this channel must be outOfService.
NTF trapVismChanReroute	1.3.6.1.4.1.351.110.0.50759	Sent when a VISM Channel is rerouted.
NTF trapVismAal2Muxing	1.3.6.1.4.1.351.110.0.50760	sent when aal2 muxing type is changed.
NTF trapVismCidState	1.3.6.1.4.1.351.110.0.50785	sent when cid state changes.
NTF trapNetworkCacConfigState	1.3.6.1.4.1.351.110.0.50788	sent when networkCacConfigState changes.
NTF trapVismFeatureChanged	1.3.6.1.4.1.351.110.0.50790	Indicates that the vismFeatureBitMap has been changed on the card.
NTF trapSMclearAllCfg	1.3.6.1.4.1.351.110.0.50800	Sent when the config is cleared.
NTF trapAusmPlppActive	1.3.6.1.4.1.351.110.0.50900	Indicates that no PLPP alarm exists
NTF trapAusmPlppInactive	1.3.6.1.4.1.351.110.0.50901	Indicates that PLPP alarm exists
NTF trapAusmPlppLbEnable	1.3.6.1.4.1.351.110.0.50904	Indicates that PLPP Loopback Enabled
NTF trapAusmPlppLbDisable	1.3.6.1.4.1.351.110.0.50905	Indicates that PLPP Loopback Disabled
NTF trapAusmPortActive	1.3.6.1.4.1.351.110.0.50910	Indicates that Port is Active and out of Alarm
NTF trapAusmPortFailed	1.3.6.1.4.1.351.110.0.50911	Indicates that Port Failed (In Alarm)
NTF trapAusmPortDelete	1.3.6.1.4.1.351.110.0.50912	Indicates that Port is Deleted
NTF trapAusmPortSvcRangeChanged	1.3.6.1.4.1.351.110.0.50913	Indicates that Port SVC resource range has changed (used for ATM T1/E1 UNI ports)
NTF trapImaPortSvcRangeChanged	1.3.6.1.4.1.351.110.0.50914	Indicates that Port SVC resource range has changed (used for IMA ports)
NTF trapPortIpChangedGeneric	1.3.6.1.4.1.351.110.0.50915	Indicates that Ip change has been detected from the CPE connected to the ausm PORT
NTF trapAusmChannelAlarm	1.3.6.1.4.1.351.110.0.50918	Sent when an AUSM logical channel is in Alarm, i.e. the channel can pass traffic within the PNNI n/w but is in Alarm because of CPE connectivity, or the line being in alarm. This trap is not applicable to MGX Release 1.x.
NTF trapAusmChannelFailed	1.3.6.1.4.1.351.110.0.50919	Sent when an AUSM logical channel fails, i.e. the channel cannot pass traffic within the PNNI n/w. This trap is not applicable to MGX Release 1.x.
NTF trapAusmChanActive	1.3.6.1.4.1.351.110.0.50920	Sent when a Channel becomes active
NTF trapAusmChanFailed	1.3.6.1.4.1.351.110.0.50921	Sent when a Channel fails (In alarm)
NTF trapAusmChanDelete	1.3.6.1.4.1.351.110.0.50922	Sent when a Channel is deleted
NTF trapAusmConDown	1.3.6.1.4.1.351.110.0.50923	Sent when a AUSM Channel is brought down. This trap is not applicable to MGX Release 1.x.
NTF trapAusmConUp	1.3.6.1.4.1.351.110.0.50924	Sent when a AUSM Channel is brought up from down. The previous RowStatus of this channel must be outOfService. This trap is not applicable to MGX Release 1.x.
NTF trapAusmChanReroute	1.3.6.1.4.1.351.110.0.50925	Sent when a AUSM Channel is rerouted. This trap is not applicable to MGX Release 1.x.
NTF trapCesmChanActiveGeneric	1.3.6.1.4.1.351.110.0.50926	Sent when a CESM Channel becomes active
NTF trapCesmChanDeleteGeneric	1.3.6.1.4.1.351.110.0.50927	Sent when a CESM Channel is deleted
NTF trapCesmChanUnderflowGeneric	1.3.6.1.4.1.351.110.0.50928	Sent when a CESM Channel egress underflows
NTF trapCesmChanOverflowGeneric	1.3.6.1.4.1.351.110.0.50929	Sent when a CESM Channel egress overflows
NTF trapCesmChanCellLossGeneric	1.3.6.1.4.1.351.110.0.50930	Sent when a CESM Channel Egress cell loss occurs
NTF trapCesmChanIdleSuppStartGeneric	1.3.6.1.4.1.351.110.0.50931	Sent when Idle suppression starts on this connection
NTF trapCesmChanIdleSuppStopGeneric	1.3.6.1.4.1.351.110.0.50932	Sent when Idle suppression stops on this connection
NTF trapCesmPortAddedGeneric	1.3.6.1.4.1.351.110.0.50933	indicates port added (enabled)
NTF trapCesmPortActiveGeneric	1.3.6.1.4.1.351.110.0.50934	indicates port active
NTF trapCesmPortFailedGeneric	1.3.6.1.4.1.351.110.0.50935	indicates port is failed
NTF trapCesmPortDeleteGeneric	1.3.6.1.4.1.351.110.0.50936	indicates port is deleted
NTF trapCesmConDown	1.3.6.1.4.1.351.110.0.50937	Sent when a CESM Channel is brought down. This object is not applicable to MGX Release 1.x.
NTF trapCesmConUp	1.3.6.1.4.1.351.110.0.50938	Sent when a CESM Channel is brought up from down. The previous RowStatus of this channel must be outOfService. This object is not applicable to MGX Release 1.x.
NTF trapCesmChanReroute	1.3.6.1.4.1.351.110.0.50939	Sent when a CESM Channel is rerouted. This object is not applicable to MGX Release 1.x.
NTF trapCesmChanActiveNew	1.3.6.1.4.1.351.110.0.50941	Sent when a CESM Channel becomes active
NTF trapCesmChanDeleteNew	1.3.6.1.4.1.351.110.0.50942	Sent when a CESM Channel is deleted
NTF trapCesmChanUnderflowNew	1.3.6.1.4.1.351.110.0.50943	Sent when a CESM Channel egress underflows
NTF trapCesmChanOverflowNew	1.3.6.1.4.1.351.110.0.50944	Sent when a CESM Channel egress overflows
NTF trapCesmChanCellLossNew	1.3.6.1.4.1.351.110.0.50945	Sent when a CESM Channel Egress cell loss occurs
NTF trapCesmChanIdleSuppStartNew	1.3.6.1.4.1.351.110.0.50946	Sent when Idle suppression starts on this connection
NTF trapCesmChanIdleSuppStopNew	1.3.6.1.4.1.351.110.0.50947	Sent when Idle suppression stops on this connection
NTF trapCesmChannelAlarm	1.3.6.1.4.1.351.110.0.50948	Sent when an CESM logical channel is in Alarm, i.e. the channel can pass traffic within the PNNI n/w but is in Alarm because of CPE connectivity, or the line being in alarm. This object is not applicable to MGX Release 1.x.
NTF trapCesmChannelFailed	1.3.6.1.4.1.351.110.0.50949	Sent when a CESM logical channel fails, i.e. the channel cannot pass traffic within the PNNI n/w. This object is not applicable to MGX Release 1.x.
NTF trapCesmChanActive	1.3.6.1.4.1.351.110.0.50950	Sent when a CESM Channel becomes active
NTF trapCesmChanDelete	1.3.6.1.4.1.351.110.0.50952	Sent when a CESM Channel is deleted
NTF trapCesmChanUnderflow	1.3.6.1.4.1.351.110.0.50960	Sent when a CESM Channel egress underflows
NTF trapCesmChanOverflow	1.3.6.1.4.1.351.110.0.50961	Sent when a CESM Channel egress overflows
NTF trapCesmChanCellLoss	1.3.6.1.4.1.351.110.0.50962	Sent when a CESM Channel Egress cell loss occurs
NTF trapCesmPortAdded	1.3.6.1.4.1.351.110.0.50971	indicates port added (enabled)
NTF trapCesmPortActive	1.3.6.1.4.1.351.110.0.50972	indicates port active
NTF trapCesmPortFailed	1.3.6.1.4.1.351.110.0.50973	indicates port failed
NTF trapCesmPortDelete	1.3.6.1.4.1.351.110.0.50974	indicates port deleted
NTF trapBbIfAdded	1.3.6.1.4.1.351.110.0.50980	Indicates that Broadband Interface is Added .
NTF trapBbIfActive	1.3.6.1.4.1.351.110.0.50981	Indicates that Broadband Interface is Active.
NTF trapBbIfDelete	1.3.6.1.4.1.351.110.0.50982	Indicates that Broadband Interface is Deleted
NTF trapBbIfFailed	1.3.6.1.4.1.351.110.0.50983	Indicates that Broadband Interface is Failed ( In alarm )
NTF trapBbIfCnfChange	1.3.6.1.4.1.351.110.0.50984	Indicates that Broadband Interface configuration has been modified.
NTF trapBbIfRscAlloc	1.3.6.1.4.1.351.110.0.50985	Indicates that Broadband Interface Resource has been allocated to a network controller ( for e.g. PAR )
NTF trapBbChanAdded	1.3.6.1.4.1.351.110.0.50990	Indicates that Broadband Channel on user port of PXM is Added
NTF trapBbChanActive	1.3.6.1.4.1.351.110.0.50991	Indicates that Broadband Channel on user port of PXM is Active and No alarms exist.
NTF trapBbChanDelete	1.3.6.1.4.1.351.110.0.50992	Sent when a Channel is deleted
NTF trapBbChanFailed	1.3.6.1.4.1.351.110.0.50993	Sent when a Channel fails (In alarm)
NTF parNodeStatusChange	1.3.6.1.4.1.351.110.0.51201	This trap is generated when a alarm status of the node (parnNodeId) changes.
NTF parNodeParmsChange	1.3.6.1.4.1.351.110.0.51202	This trap is generated when a node (parnNodeId) parameters change.
NTF parTrunkAdd	1.3.6.1.4.1.351.110.0.51203	This trap is generated when a new trunk is added in the network.
NTF parTrunkStatusChange	1.3.6.1.4.1.351.110.0.51204	This trap is generated when the status of the trunk changes or the type of alarm changes.
NTF parTrunkDelete	1.3.6.1.4.1.351.110.0.51205	This trap is generated when the trunk is deleted from the network.
NTF parTrunkConfig	1.3.6.1.4.1.351.110.0.51206	This trap is generated when the trunk parameters are configured.
NTF parUpConnStateChange	1.3.6.1.4.1.351.110.0.51207	This trap is generated when a connection is upped. This trap is generated only by the node that masters the connection.
NTF parDownConnStateChange	1.3.6.1.4.1.351.110.0.51208	This trap is generated when a connection is downed. This trap is generated only by the node that masters the connection.
NTF parConnAutoRemove	1.3.6.1.4.1.351.110.0.51209	This trap is generated when a connection is auto removed.

RFC description

Defines SNMP traps and alarms for MGX8220 and MGX8850 ATM switch platforms.

Start monitoring Cisco MGX 8200 series WAN switch (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-MGX82XX-TRAPS-MIB

What Is CISCO-MGX82XX-TRAPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description