All MIBs › CISCO-LWAPP-SYS-MIB
Organization: Cisco Systems Inc.
Last Updated: 2018-07-03
Description: MIB for global system configuration, port management, and controller-wide status on Cisco LWAPP wireless LAN controllers
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-LWAPP-SYS-MIB?
CISCO-LWAPP-SYS-MIB is a Cisco enterprise MIB implemented on Wireless LAN Controllers acting as Central Controllers for LWAPP access points, providing global system-level configuration and status information for the controller. It exposes bridging settings, firmware/certificate download and upload configuration (file type, credentials), and a network route configuration table for the controller's management interfaces. This is primarily a software configuration and system-status monitoring MIB: operators use clsDownloadFileType/clsUploadFileType and related fields to verify firmware, certificate, or PAC file transfers are configured correctly, and clsNetworkRouteConfigTable to confirm the controller's static routing is correct for reaching management and AAA systems. It depends on the broader LWAPP/CAPWAP wireless controller architecture shared with related CISCO-LWAPP-* MIBs. It is deployed on Cisco wireless LAN controllers as the central system-configuration MIB for the controller platform itself. Engineers can download the CISCO-LWAPP-SYS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-SYS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco Wireless LAN Controller (WLC)
Monitoring Examples
An administrator would check clsDownloadFileType and clsDownloadCertificateKey before initiating a firmware or certificate download to confirm the correct file type and key are set, avoiding a failed upgrade. Polling clsNetworkRouteConfigTable/clsNetworkRouteConfigEntry for clsNetworkRouteIPAddress and clsNetworkRoutePrefixLength verifies the controller's static routes to reach RADIUS/LDAP or NMS servers are correctly provisioned. Checking clsUploadPacValidity alongside clsUploadPacUsername would reveal whether an EAP-FAST PAC file upload is close to expiring.
What Can Be Monitored
- firmware/certificate download-upload configuration
- static network route table
- bridging enablement
- PAC file validity and credentials
This MIB depends on
Related MIBs
Imported Objects
From CISCO-LWAPP-DOT11-CLIENT-MIB
| cldcClientAccessVLAN | OBJECT-TYPE |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType | |
| InetPortNumber |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TimeInterval | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using clsApAssocFailedCount OID:
Select a Cisco Wireless LAN Controller (LWAPP-based) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type clsApAssocFailedCount into the Find box to locate it in the OID tree, then select it and click OK. This object represents the count when Access Point failed to associate with the controller. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoLwappSysMIB | 1.3.6.1.4.1.9.9.618 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB provides global configuration and status information for the controller. All general system related information is presented in this MIB. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Extensible Authentication Protocol ( EAP ) EAP is a universal authentication protocol used in wireless and PPP networks. It is defined by RFC 3748. EAP-Flexible Authentication ( EAP-FAST ) This protocol is used via secure tunneling for 802.1X EAP. PAC PAC (Protected Access Credential) is a meachanism for mutual authentication in EAP-FAST. PEAP The Protected Extensible Authentication Protocol, also known as Protected EAP or simply PEAP, is a protocol that encapsulates EAP within a potentially encrypted and authenticated Transport Layer Security (TLS) tunnel.The purpose was to correct deficiencies in EAP; EAP assumed a protected communication channel, such as that provided by physical security, so facilities for protection of the EAP conversation were not provided. EAP-SIM EAP for GSM Subscriber Identity Module (EAP-SIM) is used for authentication and session key distribution using the Subscriber Identity Module (SIM) from the Global System for Mobile Communications (GSM). RAID Redudant array of independant disks (RAID) combines multiple disk drive components into logical unit for the purposes of data redundancy and performance improvements. Lawful-Interception (LI) Lawful Interception is a feature to send client logging details to a server. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol. [3] IEEE 802.1X - Authentication for Wireless and Wired Connections. | ||
| ciscoLwappSysMIBNotifs | 1.3.6.1.4.1.9.9.618.0 | |||
| NTF ciscoLwappSysInvalidXmlConfig | 1.3.6.1.4.1.9.9.618.0.1 | This notification will be sent whenever invalid configuration is detected by XML. | ||
| NTF ciscoLwappNoVlanConfigured | 1.3.6.1.4.1.9.9.618.0.2 | This notification will be sent whenever wired client tries to associate without interface for specified VLAN. cldcClientAccessVLAN represents the access VLAN of the client. cldcClientMacAddress represents the MAC address of the client. | ||
| NTF ciscoLwappStrongPwdCheckNotif | 1.3.6.1.4.1.9.9.618.0.3 | This notification will be sent whenever the management user enables/disables the strong password rules. clsSecStrongPwdManagementUser represents the management user configuring the strong password security checks. clsSecStrongPwdCheckType represents the type of check that has been enabled or disabled. clsSecStrongPwdCheckOption represents the option chosen by the user. | ||
| NTF ciscoLwappSysCpuUsageHigh | 1.3.6.1.4.1.9.9.618.0.4 | This notification will be sent whenever WLC detects its CPU usage is higher than the threshold configured in clsSysControllerCpuUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its CPU usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false. | ||
| NTF ciscoLwappSysMemoryUsageHigh | 1.3.6.1.4.1.9.9.618.0.5 | This notification will be sent whenever WLC detects its memory usage is higher than the threshold configured in clsSysControllerMemoryUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its memory usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false. | ||
| NTF ciscoLwappMaxRFIDTagsReached | 1.3.6.1.4.1.9.9.618.0.6 | This notification is generated when the number of RFID tags on the controller exceeds the limit defined by clsMaxRFIDTagsTrapThreshold. | ||
| NTF ciscoLwappMaxClientsReached | 1.3.6.1.4.1.9.9.618.0.7 | This notification is generated when the number of clients on the controller exceeds the limit defined by clsMaxClientsTrapThreshold. | ||
| NTF ciscoLwappNMHeartBeat | 1.3.6.1.4.1.9.9.618.0.8 | This notification will be sent when Network Manager Heart Beat Enable. | ||
| NTF ciscoLwappCfgFileAnalyzeFail | 1.3.6.1.4.1.9.9.618.0.9 | This notification will be sent when config file analyze fails. | ||
| NTF ciscoLwappWlcUpgradeFail | 1.3.6.1.4.1.9.9.618.0.10 | This notification is generated when the wlc upgrade fails. | ||
| NTF ciscoLwappRAIDStatus | 1.3.6.1.4.1.9.9.618.0.11 | This notification is generated when the wlc hard disc status changes. | ||
| NTF ciscoLwappPortLinkSpeedTrap | 1.3.6.1.4.1.9.9.618.0.12 | This notification is generated when link speed changes in MGIG port. | ||
| ciscoLwappSysMIBObjects | 1.3.6.1.4.1.9.9.618.1 | |||
| clsConfig | 1.3.6.1.4.1.9.9.618.1.1 | |||
| T/F clsDot3BridgeEnabled | 1.3.6.1.4.1.9.9.618.1.1.1 | TruthValue | read-write | This object specifies whether 803.2 bridging mode is enabled or disabled on the controller. A value of 'true' indicates that, the bridging mode is enabled. A value of 'false' indicates that, the bridging mode is disabled. |
| clsConfigDownload | 1.3.6.1.4.1.9.9.618.1.1.2 | |||
| INT clsDownloadFileType | 1.3.6.1.4.1.9.9.618.1.1.2.1 | INTEGER | read-write | This object specifies the file types that can be downloaded to the controller. The file types for download are: unknown - Unknown file type code - Code file config - Configuration file webAuthCert - Web authentication certificates webAdminCert - Web administrative certificates signatures - Signature file customWebAuth - Custom web authentication tar file vendorDeviceCert - Vendor device certificates vendorCaCert - Vendor certificate authority certificates ipsecDeviceCert - Ipsec device certificates ipsecCaCert - Ipsec certificate authority certificates radiusavplist - Avp's to be sent in radius packets icon - icon files to be used in Hotspot 2.0 apimage - Download ap image for flexexpress naservcacert - NA server certificate authority certificates webhookcacert - Webhook CA Certificate |
| STR clsDownloadCertificateKey | 1.3.6.1.4.1.9.9.618.1.1.2.2 | SnmpAdminString | read-write | This object specifies the key used to encrypt the EAP certificate, specified by IEEE 802.1X standard, during upload from the controller and for decrypting the file after its downloaded to the controller. This object is relevant only when clsDownloadFileType is 'vendorDeviceCert'. For all other values of clsDownloadFileType object this will return an empty string. |
| clsConfigUpload | 1.3.6.1.4.1.9.9.618.1.1.3 | |||
| INT clsUploadFileType | 1.3.6.1.4.1.9.9.618.1.1.3.1 | INTEGER | read-write | This object specifies the file types that can be uploaded from the controller. The file types for upload are: unknown - Unknown file config - Configuration file errorLog - Error log systemTrace - System trace trapLog - Trap log crashFile - Crash file signatures - Signature file pac - PAC file radioCoreDump - AP's Radio core dump file invalidConfig - Upload the file which contains the invalid configuration commands feeded by the downloaded Config file. debugfile - Debug file. pktCapture - Packet Capture File watchdogCrash - Watchdog Crash Information File panicCrash - Panic Crash Information File. vendorDevCert - EAP ca certificate. vendorCaCert - EAP dev certificate. webAdminCert - Web Admin certificate. webAuthCert - Web Auth certificate. ipsecDeviceCert - Ipsec device certificates ipsecCaCert - Ipsec certificate authority certificates radiusavplist - Avp's to be sent in radius packets. yangBundle - Bundle of yang files. |
| STR clsUploadPacUsername | 1.3.6.1.4.1.9.9.618.1.1.3.2 | SnmpAdminString | read-write | This object specifies the upload user name for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string. |
| STR clsUploadPacPassword | 1.3.6.1.4.1.9.9.618.1.1.3.3 | SnmpAdminString | read-write | This object specifies the upload password for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string. When read, this object will return '****'. |
| U32 clsUploadPacValidity | 1.3.6.1.4.1.9.9.618.1.1.3.4 | Unsigned32 | read-write | This object specifies the upload validity in days for protected access credential (PAC). This object is relevant only when clsUploadFileType is set to 'pac'. For all other values of clsUploadFileType this will return an empty string. |
| clsTransferConfigGroup | 1.3.6.1.4.1.9.9.618.1.1.4 | |||
| INT clsTransferConfigFileEncryption | 1.3.6.1.4.1.9.9.618.1.1.4.1 | INTEGER | read-write | This object specifies encryption and decryption of configuration file while uploading and downloading. A value of disable(1) indicates that, encryption is disabled. A value of enable(2) indicates that, encryption is enabled. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config. |
| STR clsTransferConfigFileEncryptionKey | 1.3.6.1.4.1.9.9.618.1.1.4.2 | SnmpAdminString | read-write | This object specifies the key to be used when encrypting the configuration file while upload from the controller or while decrypting the file after download to the controller. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config. When read, this object will return '****'. |
| clsConfigGeneral | 1.3.6.1.4.1.9.9.618.1.1.5 | |||
| U32 clsTimeZone | 1.3.6.1.4.1.9.9.618.1.1.5.1 | Unsigned32 | read-write | This object specifies timezone for the controller. Enter the timezone location index. 1. (GMT-12:00) International Date Line West 2. (GMT-11:00) Samoa 3. (GMT-10:00) Hawaii 4. (GMT -9:00) Alaska 5. (GMT -8:00) Pacific Time (US and Canada) 6. (GMT -7:00) Mountain Time (US and Canada) 7. (GMT -6:00) Central Time (US and Canada) 8. (GMT -5:00) Eastern Time (US and Canada) 9. (GMT -4:00) Altantic Time (Canada) 10. (GMT -3:00) Buenos Aires (Agentina) 11. (GMT -2:00) Mid-Atlantic 12. (GMT -1:00) Azores 13. (GMT) London, Lisbon, Dublin, Edinburgh 14. (GMT +1:00) Amsterdam, Berlin, Rome, Vienna 15. (GMT +2:00) Jerusalem 16. (GMT +3:00) Baghdad 17. (GMT +4:00) Muscat, Abu Dhabi 18. (GMT +4:30) Kabul 19. (GMT +5:00) Karachi, Islamabad, Tashkent 20. (GMT +5:30) Colombo, Kolkata, Mumbai, New Delhi 21. (GMT +5:45) Katmandu 22. (GMT +6:00) Almaty, Novosibirsk 23. (GMT +6:30) Rangoon 24. (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar 25. (GMT +8:00) HongKong, Bejing, Chongquing 26. (GMT +9:00) Tokyo, Osaka, Sapporo 27. (GMT +9:30) Darwin 28. (GMT+10:00) Sydney, Melbourne, Canberra 29. (GMT+11:00) Magadan, Solomon Is., New Caledonia 30. (GMT+12:00) Kamchatka, Marshall Is., Fiji |
| STR clsTimeZoneDescription | 1.3.6.1.4.1.9.9.618.1.1.5.2 | SnmpAdminString | read-only | This object represents the timezone description for the controller. |
| U32 clsMaxClientsTrapThreshold | 1.3.6.1.4.1.9.9.618.1.1.5.3 | Unsigned32 | read-write | This object specifies the threshold for number of clients on the controller to trigger a trap. The trap ciscoLwappMaxClientsReached will be triggered once the count of clients on the controller reaches this limit and the clsMaxClientsTrapEnabled is enabled. |
| U32 clsMaxRFIDTagsTrapThreshold | 1.3.6.1.4.1.9.9.618.1.1.5.4 | Unsigned32 | read-write | This object specifies the threshold for number of RFID tags on the controller to trigger a trap. The trap ciscoLwappMaxRFIDTagsReached will be triggered once the count of RFID tags on the controller reaches this limit and the clsMaxRFIDTagsTrapEnabled is enabled. |
| clsConfigNetworkGeneral | 1.3.6.1.4.1.9.9.618.1.1.5.5 | |||
| clsNetworkRouteConfigTable | 1.3.6.1.4.1.9.9.618.1.1.5.5.1 | not-accessible | This table represents of the network route entries of a switch. | |
| clsNetworkRouteConfigEntry | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1 | not-accessible | Each entry in this table represents the network route of a switch. | |
| IPt clsNetworkRouteIPAddressType | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.1 | InetAddressType | not-accessible | This objects represents network route IP address type. |
| IP clsNetworkRouteIPAddress | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.2 | InetAddress | not-accessible | This objects represents the network route IP address. |
| U32 clsNetworkRoutePrefixLength | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.3 | Unsigned32 | read-create | This object specifies the prefix length for route Inet address. |
| IPt clsNetworkRouteGatewayType | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.4 | InetAddressType | read-create | This object specifies gateway IP type of network route. |
| IP clsNetworkRouteGateway | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.5 | InetAddress | read-create | This object specifies gateway IP of network route. |
| ROW clsNetworkRouteStatus | 1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.6 | RowStatus | read-create | This object specifies status column for this row and used to create and delete specific instances of rows in this table. |
| STR clsSensorTemperature | 1.3.6.1.4.1.9.9.618.1.1.5.6 | SnmpAdminString | read-only | This object represents current internal temperature of the unit in Centigrade |
| clsLiConfigGeneral | 1.3.6.1.4.1.9.9.618.1.1.5.7 | |||
| T/F clsLiStatus | 1.3.6.1.4.1.9.9.618.1.1.5.7.1 | TruthValue | read-write | This object specifies whether lawful intercept is enabled for the flexconnect access points connected to the wireless LAN Controller. A value of 'true' indicates that lawful intercept is enabled. A value of 'false' indicates that lawful intercept is disabled. This config is applicable for flexconnect access points. |
| NUM clsLiReportingInterval | 1.3.6.1.4.1.9.9.618.1.1.5.7.2 | TimeInterval | read-write | This object specifies the interval at which AP needs to send LI statistical information to the WLC. Interval is in the range of 60 - 600 seconds. This config is applicable for flexconnect access points. |
| IPt clsLiAddressType | 1.3.6.1.4.1.9.9.618.1.1.5.7.3 | InetAddressType | read-write | This object specifies the IP address type of the syslog server to which the LI statistics will be sent. This config is applicable for flexconnect access points. |
| IP clsLiAddress | 1.3.6.1.4.1.9.9.618.1.1.5.7.4 | InetAddress | read-write | This object specifies the IP address of the syslog server to which LI statistics needs to be sent. This config is applicable for flexconnect access points. |
| clsSyslogIpConfig | 1.3.6.1.4.1.9.9.618.1.1.6 | |||
| cLSysLogConfigTable | 1.3.6.1.4.1.9.9.618.1.1.6.1 | not-accessible | This table represents multiple syslog servers to which the the syslog messages will be sent to by the controller. | |
| cLSysLogConfigEntry | 1.3.6.1.4.1.9.9.618.1.1.6.1.1 | not-accessible | Each entry in this table provides information about the host to which the syslog messages will be sent to. | |
| U32 cLSysLogServerIndex | 1.3.6.1.4.1.9.9.618.1.1.6.1.1.1 | Unsigned32 | not-accessible | This object represents the index of the host to which syslog messages will be sent. |
| IPt cLSysLogAddressType | 1.3.6.1.4.1.9.9.618.1.1.6.1.1.2 | InetAddressType | read-create | This object represents the IP address type of the host to which syslog messages will be sent. 'DNS' is used when the hostname of the server is configured. |
| IP cLSysLogAddress | 1.3.6.1.4.1.9.9.618.1.1.6.1.1.3 | InetAddress | read-create | This object specifies the IP address or hostname of the host to which syslog messages will be sent. |
| ROW cLSysLogHostRowStatus | 1.3.6.1.4.1.9.9.618.1.1.6.1.1.4 | RowStatus | read-create | This is the status column for this row and is used to create and delete specific instances of rows in this table. |
| T/F cLSysArpUnicastEnabled | 1.3.6.1.4.1.9.9.618.1.1.7 | TruthValue | read-write | This object specifies whether ARP unicast is enabled or disabled on the controller. A value of 'true' indicates that, the ARP unicast is enabled. A value of 'false' indicates that, the ARP unicast is disabled. |
| clsTransferConfig | 1.3.6.1.4.1.9.9.618.1.1.8 | |||
| clsTransferConfigTable | 1.3.6.1.4.1.9.9.618.1.1.8.1 | not-accessible | This table represent the server details which will be used by the controller to upload/ download files. The conceptual rows are statically populated by the agent during system boot up. | |
| clsTransferConfigEntry | 1.3.6.1.4.1.9.9.618.1.1.8.1.1 | not-accessible | Each entry in this table provides information about the server to which the controller will upload/download files represented by clsTransferType and clsTransferMode. | |
| INT clsTransferType | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.1 | INTEGER | not-accessible | This object represents the type of operation mode of the server by the controller. A value of download indicates that, mode of transfer is download A value of upload indicates that, mode of transfer is upload. |
| INT clsTransferMode | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.2 | INTEGER | not-accessible | This object represents the protocol used by the server and the controller to transfer a file. A value of tftp indicates that, transfer mode is tftp. A value of ftp indicates that, transfer mode is ftp. A value of sftp indicates that, transfer mode is sftp. A value of usb indicates that, transfer mode is usb. |
| IPt clsTransferServerAddressType | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.3 | InetAddressType | read-write | This object specifies the server IP address type to which the controller will transfer the file. |
| IP clsTransferServerAddress | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.4 | InetAddress | read-write | This object specifies the server IP address to which the controller will transfer the file. It is governed by clsTransferServerAddressType. |
| STR clsTransferPath | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.5 | SnmpAdminString | read-write | This object specifies the directory path for file transfer. The format depends on the host server. e.g. /tftpboot/code/ - in case of UNIX server c:\tftp\code - in case of DOS/Windows server |
| STR clsTransferFilename | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.6 | SnmpAdminString | read-write | This object specifies the file name for the file being transferred from the controller. An example would be file path set to c:\tftp\code\ and file name set to e1r1v1.opr. |
| STR clsTransferFtpUsername | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.7 | SnmpAdminString | read-write | This object specifies the FTP username for transferring file on the server. This is valid for FTP/SFTP transfer mode parameters. |
| STR clsTransferFtpPassword | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.8 | SnmpAdminString | read-write | This object specifies the FTP password for transferring file on the server. This is valid for SFTP/FTP transfer mode parameters. It returns '****' when queried. |
| INE clsTransferFtpPortNum | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.9 | InetPortNumber | read-write | This object specifies the port number to be used by the FTP protocol while connecting to the server. This is valid only for FTP transfer mode. |
| U32 clsTransferTftpMaxRetries | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.10 | Unsigned32 | read-write | This object specifies maximum number of retries to be allowed for a TFTP message packet before aborting the transfer operation. This is valid only for TFTP transfer mode. |
| U32 clsTransferTftpTimeout | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.11 | Unsigned32 | read-write | This object specifies timeout in seconds for a TFTP message packet. This is valid only for TFTP transfer mode. |
| INT clsTransferStart | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.12 | INTEGER | read-write | This object specifies whether the file transfer operation is initiated in active or standby. A value of none indicates that, no operation begins. A value of initiate indicates that, transfer of file begins on active. A value of initiatePeer indicates that, file transfer operation begins on standby. |
| INT clsTransferStatus | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.13 | INTEGER | read-only | This object represents the current status of a file transfer operation. The following are valid only when clsTransferType is 'download' :- bootBreakOff(14), invalidTarFile(15). A value of unknown(1) indicates that, unknown state of transfer. A value of notInitiated(2) indicates that, no transfer operation has been initiated A value of transferStarting(3) indicates that, transfer operation has commenced. A value of errorStarting(4) indicates that, error while starting transfer operation. A value of wrongFileType(5) indicates that, wrong file type specified. A value of updatingConfig(6) indicates that, updating configuration. A value of invalidConfigFile(7) indicates that, invalid config file specified. A value of writingToFlash(8) indicates that, writing to flash A value of failureWritingToFlash(9) indicates that, writing to flash failed. A value of checkingCRC(10) indicates that, checking cyclic redundancy check. A value of failedCRC(11) indicates that, CRC check failed. A value of unknownDirection(12) indicates that, unknown direction of transfer. A value of transferSuccessful(13) indicates that, transfer operation succeeded. A value of transferFailed(14) indicates that, transfer failed. A value of bootBreakOff(15) indicates that, Boot break off. A value of invalidTarFile(16) indicates that, invalid Tar file. |
| STR clsTransferStatusString | 1.3.6.1.4.1.9.9.618.1.1.8.1.1.14 | SnmpAdminString | read-only | This object represents the current status of a file transfer operation in human readable format. |
| clsStreamingTransferConfig | 1.3.6.1.4.1.9.9.618.1.1.8.2 | |||
| clsApTransferTable | 1.3.6.1.4.1.9.9.618.1.1.8.2.1 | not-accessible | This table represents the information about the 802.11 LWAPP Access Points that have joined to the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller. | |
| clsApTransferEntry | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1 | not-accessible | Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined to the controller. Entries are removed when the APs lose their association with the controller due to loss of communication. | |
| MAC clsApTransferSysMacAddress | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.1 | MacAddress | not-accessible | This object represents the radio MAC address of the AP and uniquely identifies an entry in this table. |
| STR clsApPrimaryVers | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.2 | SnmpAdminString | read-only | This object represents the primary image version of AP |
| STR clsApBackupVers | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.3 | SnmpAdminString | read-only | This object represents the backup image version of AP |
| STR clsApPredStatus | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.4 | SnmpAdminString | read-only | This object represents the status of predownload, Initiated/failed/predownloading/backedoff |
| STR clsApPredFailReason | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.5 | SnmpAdminString | read-only | This object represents Failure reason for image download. |
| U32 clsApPredRetryCount | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.6 | Unsigned32 | read-only | This object represents number of retries by AP to download the image |
| STR clsApPredNextRetryTime | 1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.7 | SnmpAdminString | read-only | This object represents the next retry time of image download by AP. |
| INT clsTransferStreamingMode | 1.3.6.1.4.1.9.9.618.1.1.8.2.2 | INTEGER | read-write | This object specifies the mode of transfer used by the controller with the server. A value of tftp indicates that, streaming mode is TFTP. A value of http indicates that, streaming mode is http. A value of cco indicates that, streaming mode is cco. A value of https indicates that, streaming mode is https. A value of sftp indicates that, streaming mode is sftp. |
| IPt clsTransferStreamingServerAddressType | 1.3.6.1.4.1.9.9.618.1.1.8.2.3 | InetAddressType | read-write | This object specifies the server IP address type from which the controller will transfer the image file. |
| IP clsTransferStreamingServerAddress | 1.3.6.1.4.1.9.9.618.1.1.8.2.4 | InetAddress | read-write | This object specifies the server IP address to which the controller will transfer the file. |
| STR clsTransferStreamingPath | 1.3.6.1.4.1.9.9.618.1.1.8.2.5 | SnmpAdminString | read-write | This object specifies the directory path for file transfer. The controller remembers the last file path used. |
| INT clsStreamingTransferStart | 1.3.6.1.4.1.9.9.618.1.1.8.2.6 | INTEGER | read-write | This object specifies whether the file transfer operation started or not. A value of initiate(1) indicates that, the transfer operation is started. A value of none(2) indicates that, no operation is started |
| STR clsTransferHttpStreamingUsername | 1.3.6.1.4.1.9.9.618.1.1.8.2.7 | SnmpAdminString | read-write | This object specifies username of CCO server. Specific to http/cco mode |
| STR clsTransferHttpStreamingPassword | 1.3.6.1.4.1.9.9.618.1.1.8.2.8 | SnmpAdminString | read-write | This object specifies password of CCO server. Specific to http/cco mode |
| STR clsTransferHttpStreamingSuggestedVersion | 1.3.6.1.4.1.9.9.618.1.1.8.2.9 | SnmpAdminString | read-only | This object represents suggested image version to be downloaded from CCO.Specific to http/cco mode |
| STR clsTransferHttpStreamingLatestVersion | 1.3.6.1.4.1.9.9.618.1.1.8.2.10 | SnmpAdminString | read-only | This object represents latest image version to be downloaded from CCO.Specific to http/cco mode |
| STR clsTransferHttpStreamingCcoPoll | 1.3.6.1.4.1.9.9.618.1.1.8.2.11 | SnmpAdminString | read-only | This object represents recent CCO Polled time |
| I32 clsTransferStreamingServerPort | 1.3.6.1.4.1.9.9.618.1.1.8.2.12 | Integer32 | read-write | This object represents streaming server port for https/sftp |
| STR clsTransferStreamingUsername | 1.3.6.1.4.1.9.9.618.1.1.8.2.13 | SnmpAdminString | read-write | This object specifies username of server. Specific to https/sftp mode |
| STR clsTransferStreamingPassword | 1.3.6.1.4.1.9.9.618.1.1.8.2.14 | SnmpAdminString | read-write | This object specifies password of server. Specific to https/sftp mode |
| T/F clsTransferStreamingOptimizedJoinEnable | 1.3.6.1.4.1.9.9.618.1.1.8.2.15 | TruthValue | read-write | This object specified the state of the optimized join feature. |
| T/F cLSysBroadcastForwardingEnabled | 1.3.6.1.4.1.9.9.618.1.1.9 | TruthValue | read-write | This object specifies whether broadcast forwarding is enabled or disabled on the controller. A value of 'true' indicates that, the broadcast forwarding is enabled. A value of 'false' indicates that, the broadcast forwarding is disabled. |
| T/F cLSysLagModeEnabled | 1.3.6.1.4.1.9.9.618.1.1.10 | TruthValue | read-write | This object specifies whether Link Aggregation(LAG) mode is enabled or disabled on the controller. A value of 'true' indicates that, the LAG mode is enabled. A value of 'false' indicates that, the LAG mode is disabled on the controller. |
| STR clsConfigProductBranchVersion | 1.3.6.1.4.1.9.9.618.1.1.11 | SnmpAdminString | read-only | This object represents the branch name of the specific controller branch. For Mesh branches, this string has the value M(Mesh). Zero length string is returned if there is no branch name. This string is append to the product version for display purposes. For example, if the mesh product version is 4.1.191.10, a manager application may the version string as 4.1.191.10M (Mesh) |
| T/F clsConfigDhcpProxyEnabled | 1.3.6.1.4.1.9.9.618.1.1.12 | TruthValue | read-write | This object specifies whether the DHCP proxy option is enabled or disabled. A value of 'true' indicates that, the proxy option is enabled on the controller. A value of 'false' indicates that, the proxy option is disabled on the controller. |
| cLSysMulticastIGMP | 1.3.6.1.4.1.9.9.618.1.1.13 | |||
| T/F cLSysMulticastIGMPSnoopingEnabled | 1.3.6.1.4.1.9.9.618.1.1.13.1 | TruthValue | read-write | This object specifies whether Multicast IGMP Snooping is enabled or disabled on the controller. A value of 'true' indicates that the Multicast IGMP Snooping is enabled. To enable this, agentNetworkMulticastMode/clsConfigMulticastEnabled must not be in disabled state. A value of 'false' indicates that the Multicast IGMP Snooping is disabled on the controller. |
| U32 cLSysMulticastIGMPSnoopingTimeout | 1.3.6.1.4.1.9.9.618.1.1.13.2 | Unsigned32 | read-write | This object specifies the IGMP timeout, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to true. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller. |
| U32 cLSysMulticastIGMPQueryInterval | 1.3.6.1.4.1.9.9.618.1.1.13.3 | Unsigned32 | read-write | This object specifies the IGMP query interval, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to true. |
| T/F cLSysMulticastLLBridgingStatus | 1.3.6.1.4.1.9.9.618.1.1.13.4 | TruthValue | read-write | This object specifies whether link local is enabled or disabled on the controller. A value of 'true' indicates that the link local is enabled. A value of 'false' indicates that the link local is disabled on the controller. |
| cLSPortModeConfig | 1.3.6.1.4.1.9.9.618.1.1.14 | |||
| clsPortModeConfigTable | 1.3.6.1.4.1.9.9.618.1.1.14.1 | not-accessible | This table represents the entries for physical port related parameters. | |
| clsPortModeConfigEntry | 1.3.6.1.4.1.9.9.618.1.1.14.1.1 | not-accessible | Each entry contains the switch's physical port, phyical mode related attribues. Each entry exists for available physical interface. Entries cannot be created or deleted by the user. | |
| U32 clsPortDot1dBasePort | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.1 | Unsigned32 | not-accessible | This object represents unique unsigned integer value which identifies the base port number. |
| INT clsPortModePhysicalMode | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.2 | INTEGER | read-write | The object specifies the speed mode of switch port. A value of autoNegotiate indicates that, port senses speed and negotiates with the port at the other end of the link for data transfer operation A value of half10 indicates that, port operates at 10mbps half duplex speed. A value of full10 indicates that, port operates at 10mbps full duplex speed. A value of half100 indicates that, port operates at 100mbps half duplex speed. A value of full100 indicates that, port operates at 100mbps full duplex speed. A value of full1000sx indicates that, port operates at 1000mbps full duplex speed over multi mode fiber. A value of half1000 indicates that, port operates at 1000mbps half duplex speed. A value of full1000 indicates that, port operates at 1000mbps full duplex speed. A value of half10000 indicates that, port operates at 10000mbps half duplex speed. A value of full10000 indicates that, port operates at 10000mbps full duplex speed. |
| INT clsPortModePhysicalStatus | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.3 | INTEGER | read-only | This object represents the switch port's current physical speed status. A value of unknown indicates that, the speed of the port is not known A value of autoNegotiate indicates that, port senses speed and negotiates with the port at the other end of the link for data transfer operation A value of half10 indicates that, port operates at 10mbps half duplex speed. A value of full10 indicates that, port operates at 10mbps full duplex speed. A value of half100 indicates that, port operates at 100mbps half duplex speed. A value of full100 indicates that, port operates at 100mbps full duplex speed A value of full1000sx indicates that, port operates at 1000mbps full duplex speed over multi mode fiber. A value of half1000 indicates that, port operates at 1000mbps half duplex speed. A value of full1000 indicates that, port operates at 1000mbps full duplex speed. A value of half2500 indicates that, port operates at 2500mbps half duplex speed. A value of full2500 indicates that, port operates at 2500mbps full duplex speed. A value of half5000 indicates that, port operates at 5000mbps half duplex speed. A value of full5000 indicates that, port operates at 5000mbps full duplex speed. A value of half10000 indicates that, port operates at 10000mbps half duplex speed. A value of full10000 indicates that, port operates at 10000mbps full duplex speed. |
| STR clsPortModeSfpType | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.4 | SnmpAdminString | read-only | This object represents the SFP type of the port. When there is no SFP connected to the port, the string is represented with value as Not Present. |
| C32 clsPortUpDownCount | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.5 | Counter32 | read-only | This object represents the total number of up/down count of the port. Every time the value of ifOperStatus is changed, this MIB object should be incremented. |
| INT clsPortModeMaxSpeed | 1.3.6.1.4.1.9.9.618.1.1.14.1.1.6 | INTEGER | read-write | The object specifies the maxspeed mode of MGIG port. A value of full1000 indicates that, port will operate at maximum autonegotiated speed of 1000mbps or less. A value of full2500 indicates that, port will operate at maximum autonegotiated speed of 2500mbps or less. A value of full5000 indicates that, port will operate at maximum autonegotiated speed of 5000mbps or less. |
| clsCoreDump | 1.3.6.1.4.1.9.9.618.1.1.15 | |||
| T/F clsCoreDumpTransferEnable | 1.3.6.1.4.1.9.9.618.1.1.15.1 | TruthValue | read-write | This object specifies whether the core dump file transfer is enabled or disabled. A value of 'true' indicates that, the core dump file transfer is enabled. A value of 'false' indicates that , the core dump file transfer is disabled |
| INT clsCoreDumpTransferMode | 1.3.6.1.4.1.9.9.618.1.1.15.2 | INTEGER | read-write | This object specifies the Core Dump Transfer Mode. A value 'unknown' cannot be set. A value of ftp indicates that, mode is ftp. FTP attributes clsCoreDumpServerIpAddress, clsCoreDumpFileName, clsCoreDumpUserName, clsCoreDumpPassword can be set. unknown when the value of clsCoreDumpTransferEnable is disabled. |
| IPt clsCoreDumpServerIPAddressType | 1.3.6.1.4.1.9.9.618.1.1.15.3 | InetAddressType | read-write | This object specifies the IP address type of the server. |
| IP clsCoreDumpServerIPAddress | 1.3.6.1.4.1.9.9.618.1.1.15.4 | InetAddress | read-write | This object specifies the IP address of the server where the core-dump will be uploaded. The type of this address is determined by the value of clsCoreDumpServerIpAddressType object. |
| STR clsCoreDumpFileName | 1.3.6.1.4.1.9.9.618.1.1.15.5 | SnmpAdminString | read-write | This object specifies the filename of the core-dump by which it gets uploaded on the server. |
| STR clsCoreDumpUserName | 1.3.6.1.4.1.9.9.618.1.1.15.6 | SnmpAdminString | read-write | This object specifies the login name at the FTP server. |
| STR clsCoreDumpPassword | 1.3.6.1.4.1.9.9.618.1.1.15.7 | SnmpAdminString | read-write | This object specifies the login password of the FTP server. |
| T/F clsConfigMulticastEnabled | 1.3.6.1.4.1.9.9.618.1.1.16 | TruthValue | read-write | This object specifies whether global multicast is enabled or disabled. A value of 'true' indicates that the multicast option is enabled on the controller. A value of 'false' indicates that the multicast option is disabled on the controller. |
| cLSysMulticastMLD | 1.3.6.1.4.1.9.9.618.1.1.17 | |||
| T/F cLSysMulticastMLDSnoopingEnabled | 1.3.6.1.4.1.9.9.618.1.1.17.1 | TruthValue | read-write | This object specifies whether multicast MLD Snooping is enabled or disabled on the controller. A value of 'true' indicates that the multicast MLD Snooping is enabled. To enable this, agentNetworkMulticastMode/ clsConfigMulticastEnabled must not be in disabled state. A value of 'false' indicates that the multicast MLD Snooping is disabled on the controller. |
| U32 cLSysMulticastMLDSnoopingTimeout | 1.3.6.1.4.1.9.9.618.1.1.17.2 | Unsigned32 | read-write | This object specifies the MLD timeout, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to True. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller. |
| U32 cLSysMulticastMLDQueryInterval | 1.3.6.1.4.1.9.9.618.1.1.17.3 | Unsigned32 | read-write | This object specifies the MLD query interval, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to true. |
| clsConfigStats | 1.3.6.1.4.1.9.9.618.1.1.18 | |||
| U32 clsSysRealtimeStatsTimer | 1.3.6.1.4.1.9.9.618.1.1.18.1 | Unsigned32 | read-write | This object specifies the realtime stats interval of the system. There are 2 stats modes: realtime and normal. Realtime interval is much less than normal mode. |
| U32 clsSysNormalStatsTimer | 1.3.6.1.4.1.9.9.618.1.1.18.2 | Unsigned32 | read-write | This object specifies the normal stats interval of the system. There are 2 stats modes: realtime and normal. Realtime interval is much less than normal mode. |
| U32 clsSysStatsSamplingInterval | 1.3.6.1.4.1.9.9.618.1.1.18.3 | Unsigned32 | read-write | This object specifies the sampling interval of the system, which is applied to WLC and APs connected to this WLC. WLC and APs poll specific data every sampling interval. |
| U32 clsSysStatsAverageInterval | 1.3.6.1.4.1.9.9.618.1.1.18.4 | Unsigned32 | read-write | This object specifies the average statistics interval of the system, which is applied to WLC and APs connected to this WLC. This interval works as a time window for calculating the average value of the data polled by WLC/AP every sampling interval. |
| clsAlarmObjects | 1.3.6.1.4.1.9.9.618.1.1.19 | |||
| U32 clsAlarmHoldTime | 1.3.6.1.4.1.9.9.618.1.1.19.1 | Unsigned32 | read-write | This object specifies the time in seconds for which an alarm object should be soaked when its on/off state is changed. |
| U32 clsAlarmTrapRetransmitInterval | 1.3.6.1.4.1.9.9.618.1.1.19.2 | Unsigned32 | read-write | This object specifies the trap retransmission interval in seconds. Setting this value to 0 means no retransmission. |
| clsSysThresholdConfig | 1.3.6.1.4.1.9.9.618.1.1.20 | |||
| U32 clsSysControllerCpuUsageThreshold | 1.3.6.1.4.1.9.9.618.1.1.20.1 | Unsigned32 | read-write | This object specifies the CPU usage threshold on a controller. Setting this value to 0 means no threshold. |
| U32 clsSysControllerMemoryUsageThreshold | 1.3.6.1.4.1.9.9.618.1.1.20.2 | Unsigned32 | read-write | This object specifies the memory usage threshold on a controller. Setting this value to 0 means no threshold. |
| U32 clsSysApCpuUsageThreshold | 1.3.6.1.4.1.9.9.618.1.1.20.3 | Unsigned32 | read-write | This object specifies the CPU usage threshold on a AP. Setting this value to 0 means no threshold. |
| U32 clsSysApMemoryUsageThreshold | 1.3.6.1.4.1.9.9.618.1.1.20.4 | Unsigned32 | read-write | This object specifies the memory usage threshold on a AP. Setting this value to 0 means no threshold. |
| clsNMHeartBeat | 1.3.6.1.4.1.9.9.618.1.1.21 | |||
| T/F clsNMHeartBeatEnable | 1.3.6.1.4.1.9.9.618.1.1.21.1 | TruthValue | read-write | This object specifies whether heart beat trap to network manager is enabled or disabled. A value of 'true' indicates that, network manager heart beat feature is enabled. A value of 'false' indicates that, network manager heart beat feature is disabled. |
| U32 clsNMHeartBeatInterval | 1.3.6.1.4.1.9.9.618.1.1.21.2 | Unsigned32 | read-write | This object specifies the heart beat trap interval in seconds to network manager. |
| T/F clsSysLogEnabled | 1.3.6.1.4.1.9.9.618.1.1.22 | TruthValue | read-write | This object specifies whether debug log to syslog is enabled or disabled. A value of 'true' indicates that debug log to syslog is enabled on the controller. A value of 'false' indicates that debug log to syslog is disabled on the controller. |
| INT clsSysLogLevel | 1.3.6.1.4.1.9.9.618.1.1.23 | INTEGER | read-write | This object specifies the debug log level that can be send to syslog on the controller. The level for syslog are: emergencies - system is unusable alerts - action must be taken immediately critical - critical conditions errors - error conditions warnings - warning conditions notifications - normal but signification condition informational - Informational debugging - debug-level messages. |
| U32 clsConfigApMaxCount | 1.3.6.1.4.1.9.9.618.1.1.24 | Unsigned32 | read-only | This object represents the the max number of AP's supported in WLC. |
| cLSTrapSwitchConfig | 1.3.6.1.4.1.9.9.618.1.1.25 | |||
| clsTrapBlacklistTable | 1.3.6.1.4.1.9.9.618.1.1.25.1 | not-accessible | This table represents the trap blacklist. Traps in black list will be blocked while sending out. | |
| clsTrapBlacklistEntry | 1.3.6.1.4.1.9.9.618.1.1.25.1.1 | not-accessible | Each entry in this table provides the name of trap in trap blacklist. | |
| U32 clsBlacklistTrapIndex | 1.3.6.1.4.1.9.9.618.1.1.25.1.1.1 | Unsigned32 | not-accessible | This object represents trap uniquely in blacklist. |
| STR clsTrapNameInBlacklist | 1.3.6.1.4.1.9.9.618.1.1.25.1.1.2 | SnmpAdminString | read-create | This object specifies name of trap in trap blacklist. |
| ROW clsTrapBlacklistRowStatus | 1.3.6.1.4.1.9.9.618.1.1.25.1.1.3 | RowStatus | read-create | This is the status column for this row and used to create and delete specific instances of rows in this table. |
| T/F clsLinkLocalBridgingEnabled | 1.3.6.1.4.1.9.9.618.1.1.26 | TruthValue | read-write | This object specifies whether link local bridging on client packets is enabled or disabled. A value of 'true' indicates that link local bridging on client packets is enabled on the controller. A value of 'false' indicates that link local bridging on client packets is disabled on the controller. |
| U32 clsNetworkHttpProfCustomPort | 1.3.6.1.4.1.9.9.618.1.1.27 | Unsigned32 | read-write | This object specifies the custom port for http profiling. |
| clsIconCfgTable | 1.3.6.1.4.1.9.9.618.1.1.28 | not-accessible | This table represents the generic icon file configuration in the controller. It has only one argument; the icon file name which shall be used to index the rows in this table. | |
| clsIconCfgEntry | 1.3.6.1.4.1.9.9.618.1.1.28.1 | not-accessible | Each entry in this table represents the icon config entry | |
| STR clsIconCfgFileName | 1.3.6.1.4.1.9.9.618.1.1.28.1.1 | SnmpAdminString | not-accessible | This object represents the icon filename |
| STR clsIconCfgFileType | 1.3.6.1.4.1.9.9.618.1.1.28.1.2 | SnmpAdminString | read-create | This object specifies the filetype of the icon file |
| STR clsIconCfgLangCode | 1.3.6.1.4.1.9.9.618.1.1.28.1.3 | SnmpAdminString | read-create | This object specifies the language code associated with the icon file |
| U32 clsIconCfgWidth | 1.3.6.1.4.1.9.9.618.1.1.28.1.4 | Unsigned32 | read-create | This object specifies the width of the icon file |
| U32 clsIconCfgHeight | 1.3.6.1.4.1.9.9.618.1.1.28.1.5 | Unsigned32 | read-create | This object specifies the height of the icon file |
| ROW clsIconCfgRowStatus | 1.3.6.1.4.1.9.9.618.1.1.28.1.6 | RowStatus | read-create | This object specifies status column for this row and used to create and delete specific instances of rows in this table. |
| U32 clsNetworkHttpProxyPort | 1.3.6.1.4.1.9.9.618.1.1.29 | Unsigned32 | read-write | This object specifies the custom port for http proxy |
| IPt clsNetworkHttpProxyIpType | 1.3.6.1.4.1.9.9.618.1.1.30 | InetAddressType | read-write | This object specifies the http proxy IP address type |
| IP clsNetworkHttpProxyIp | 1.3.6.1.4.1.9.9.618.1.1.31 | InetAddress | read-write | This Object specifies the IP address of the http proxy |
| IPt clsNetworkDnsServerIpType | 1.3.6.1.4.1.9.9.618.1.1.32 | InetAddressType | read-write | This object specifies the DNS server IP address type |
| IP clsNetworkDnsServerIp | 1.3.6.1.4.1.9.9.618.1.1.33 | InetAddress | read-write | This Object specifies the IP address of the DNS server |
| clsConfigCalea | 1.3.6.1.4.1.9.9.618.1.1.34 | |||
| T/F clsConfigCaleaEnabled | 1.3.6.1.4.1.9.9.618.1.1.34.1 | TruthValue | read-write | This object specifies whether CALEA lawful Intercept feature enabled or disabled. A value of 'true' indicates that, CALEA lawful Intercept feature enabled. A value of 'false'indicates that, CALEA lawful Intercept feature disabled. |
| IP clsConfigCaleaServerIp | 1.3.6.1.4.1.9.9.618.1.1.34.2 | IpAddress | read-write | This object specifies the address of the CALEA lawful intercept server |
| INE clsConfigCaleaPort | 1.3.6.1.4.1.9.9.618.1.1.34.3 | InetPortNumber | read-write | This object specifies about port number of CALEA lawful intercept server |
| U32 clsConfigCaleaAccountingInterval | 1.3.6.1.4.1.9.9.618.1.1.34.4 | Unsigned32 | read-write | This object specifies the accounting interval of CALEA lawful intercept. |
| STR clsConfigCaleaVenue | 1.3.6.1.4.1.9.9.618.1.1.34.5 | SnmpAdminString | read-write | This object specifies the CALEA Venue description |
| IPt clsConfigCaleaServerIpType | 1.3.6.1.4.1.9.9.618.1.1.34.6 | InetAddressType | read-write | This Object specifies the address type of the CALEA lawful intercept server |
| IP clsConfigCaleaServerIpAddr | 1.3.6.1.4.1.9.9.618.1.1.34.7 | IpAddress | read-write | This Object specifies the IPv4 address of the CALEA lawful intercept server |
| T/F clSysLogIPSecStatus | 1.3.6.1.4.1.9.9.618.1.1.35 | TruthValue | read-write | This object specifies Syslog over IPSEC Status A value of 'true' indicates that, syslog over ipsec is enabled. A value of 'false' indicates that syslog over ipsec is disabled. |
| STR clSysLogIPSecProfName | 1.3.6.1.4.1.9.9.618.1.1.36 | SnmpAdminString | read-write | This object specifies IPsec profile to be used for syslog over IPSec. |
| T/F clsConfigArpUnicastEnabled | 1.3.6.1.4.1.9.9.618.1.1.37 | TruthValue | read-write | This object specifies whether arp is forwarded in unicast format or the default mode of Multicast. A value of 'true' indicates that, the arp packets for passive client will be unicasted. A value of 'false' indicates that, the arp-packets will be sent based on the config of multicast mode multicast/unicast. |
| T/F clsWGBForcedL2RoamEnabled | 1.3.6.1.4.1.9.9.618.1.1.38 | TruthValue | read-write | This object specifies whether forced L2 Roaming is enabled or disable for WGB clients. A value of 'true' indicates that, forced L2 Roaming is enabled for WGB clients. A value of 'false' indicates that, forced L2 Roaming is disabled for WGB clients. |
| T/F clsUSBMode | 1.3.6.1.4.1.9.9.618.1.1.40 | TruthValue | read-write | This object specifies whether USB is enabled or disabled. A value of 'true' indicates that, USB is enabled. A value of 'false' indicates that, USB is disabled. |
| T/F clsCrashSystem | 1.3.6.1.4.1.9.9.618.1.1.99 | TruthValue | read-write | This object specifies whether to reset the switch with a crash or not. A value of 'true' indicates that, the switch would crash. A value of 'false'indicates that, not crashed. |
| clsStatus | 1.3.6.1.4.1.9.9.618.1.2 | |||
| T/F cLSysLagModeInTransition | 1.3.6.1.4.1.9.9.618.1.2.1 | TruthValue | read-only | This object represents whether the LAG mode is in transition or not. A value of 'true' indicates that, the LAG mode is in transition and the controller has to be rebooted to take effect. A value of 'false' indicates that, the LAG mode is not in transition. |
| clsRAIDStatusTable | 1.3.6.1.4.1.9.9.618.1.2.2 | not-accessible | This table represents the RAID and rebuild status. | |
| clsRAIDStatusEntry | 1.3.6.1.4.1.9.9.618.1.2.2.1 | not-accessible | Each entry in this table provides RAID drive status. | |
| U32 clsRAIDDriveNumber | 1.3.6.1.4.1.9.9.618.1.2.2.1.1 | Unsigned32 | not-accessible | This object indicates drive number in the system. |
| INT clsRAIDStatus | 1.3.6.1.4.1.9.9.618.1.2.2.1.2 | INTEGER | read-only | This object represents the status of the drive. A value of good indicates that, hard disk in RAID volume is good. A value of bad indicates that, hard disk in RAID volume is bad. A value of badstartrebuild indicates that, hard disk in RAID volume is bad and rebuild is triggered. A value of rebuilding indicates that, hard disk in RAID volume is rebuilding. |
| U32 clsRAIDRebuildPercentage | 1.3.6.1.4.1.9.9.618.1.2.2.1.3 | Unsigned32 | read-only | This object represents the rebuild percentage of drive. This object is applicable only when RAID status is rebuilding. |
| clsSysPingTestTable | 1.3.6.1.4.1.9.9.618.1.2.3 | not-accessible | This table represents the test ping entries | |
| clsSysPingTestEntry | 1.3.6.1.4.1.9.9.618.1.2.3.1 | not-accessible | Each Entry (conceptual row) in the clsSysPingTest Table represents a ping test id. | |
| I32 clsSysPingTestId | 1.3.6.1.4.1.9.9.618.1.2.3.1.1 | Integer32 | not-accessible | This object represents the index of pingtest ID |
| IPt clsSysPingTestIPAddressType | 1.3.6.1.4.1.9.9.618.1.2.3.1.2 | InetAddressType | read-create | This object specifies the IP address type |
| IP clsSysPingTestIPAddress | 1.3.6.1.4.1.9.9.618.1.2.3.1.3 | InetAddress | read-create | This object specifies the IP address of the device to which ping test to perform |
| I32 clsSysPingTestSendCount | 1.3.6.1.4.1.9.9.618.1.2.3.1.4 | Integer32 | read-create | This object specifies the number of bytes sent |
| I32 clsSysPingTestReceivedCount | 1.3.6.1.4.1.9.9.618.1.2.3.1.5 | Integer32 | read-only | This object represents the number of bytes received. |
| INT clsSysPingTestStatus | 1.3.6.1.4.1.9.9.618.1.2.3.1.6 | INTEGER | read-only | This object represents status of the ping test. A value of inprogress indicates that, ping test in progress. A value of complete indicates that, ping test is complete. |
| U32 clsSysPingTestMaxTimeInterval | 1.3.6.1.4.1.9.9.618.1.2.3.1.7 | Unsigned32 | read-only | This object represents maximum time interval in msec. |
| U32 clsSysPingTestMinTimeInterval | 1.3.6.1.4.1.9.9.618.1.2.3.1.8 | Unsigned32 | read-only | This object represents minimum time interval in msec. |
| U32 clsSysPingTestAvgTimeInterval | 1.3.6.1.4.1.9.9.618.1.2.3.1.9 | Unsigned32 | read-only | This object represents average time interval in msec. |
| ROW clsSysPingTestRowStatus | 1.3.6.1.4.1.9.9.618.1.2.3.1.10 | RowStatus | read-create | This is the status column for this row and used to create and delete specific instances of rows in this table. |
| clsImageInfo | 1.3.6.1.4.1.9.9.618.1.3 | |||
| STR clsEmergencyImageVersion | 1.3.6.1.4.1.9.9.618.1.3.1 | SnmpAdminString | read-only | This object represents Cisco recommends installing Cisco Unified Wireless Network Controller Boot Software , (*_ER.aes , where star denotes the version of the controller image ) on all controller platforms. If this ER.aes is not installed, the controller would not be able to show the Emergency Image Version correctly(or Field Recovery Image Version), and would be shown as 'N/A'. The ER.aes files are independent from the controller software files. Any controller software file can be run with any ER.aes file. However, installing the latest boot software file (*_ER.aes , where star denotes the controller version) ensures that the boot software modifications in all of the previous and current boot software ER.aes files are installed. |
| clsCpuInfo | 1.3.6.1.4.1.9.9.618.1.4 | |||
| STR clsAllCpuUsage | 1.3.6.1.4.1.9.9.618.1.4.1 | SnmpAdminString | read-only | This object represents the CPU usage string. |
| clsSecurityGroup | 1.3.6.1.4.1.9.9.618.1.5 | |||
| T/F clsSecStrongPwdCaseCheck | 1.3.6.1.4.1.9.9.618.1.5.1 | TruthValue | read-write | This object specifies the whether password case check is enabled or disabled. A value of 'true' indicates that, the new password must contain characters from at least three of the following classes : lowercase letters, uppercase letters, digits and special characters. A value of 'false' indicates that, no checks for password. |
| T/F clsSecStrongPwdConsecutiveCheck | 1.3.6.1.4.1.9.9.618.1.5.2 | TruthValue | read-write | This object specifies whether the password consecutive check is enabled or disabled. A value of 'true' indicates that, the password provided should not have a character repeated more than thrice consecutively. A value of 'false' indicates that, character repeatation check disabled |
| T/F clsSecStrongPwdDefaultCheck | 1.3.6.1.4.1.9.9.618.1.5.3 | TruthValue | read-write | This object specifies whether default check for the passwords is enabled or disabled. A value of 'true' indicates that, the new password must not be 'cisco', 'ocsic', 'admin', 'nimda' or any variant obtained by changing the capitalization of letters therein, or by substituting '1' '|' or '!' for i, and/or substituting '0' for 'o', and/or substituting '$' for 's'. A value of 'false' indicates that, default check disabled for the password. |
| T/F clsSecStrongPwdAsUserNameCheck | 1.3.6.1.4.1.9.9.618.1.5.4 | TruthValue | read-write | This object specifies whether username check for the password is enabled or disabled. A value of 'true' indicates that, the new password must not be same as the associated username or the reversed username. A value of 'false' indicates that, check for user name in the password is disabled |
| T/F clsSecStrongPwdPositionCheck | 1.3.6.1.4.1.9.9.618.1.5.5 | TruthValue | read-write | This object specifies whether position check for the passwords is enabled or disabled. A value of 'true' indicates that, position check for the password is enabled. A value of 'false' indicates that, position check for the password is disabled. |
| T/F clsSecStrongPwdDigitCheck | 1.3.6.1.4.1.9.9.618.1.5.6 | TruthValue | read-write | This object specifies whether digit check for the passwords is enabled or disabled. A value of 'true' indicates that, digit check for the passwords is enabled. A value of 'false' indicates that, digit check for the passwords is disabled. |
| U32 clsSecStrongPwdMinLength | 1.3.6.1.4.1.9.9.618.1.5.7 | Unsigned32 | read-write | This object specifies the minimum password length for the passwords configured in controller. |
| U32 clsSecStrongPwdMinUpperCase | 1.3.6.1.4.1.9.9.618.1.5.8 | Unsigned32 | read-write | This object specifies the minimum number of upper case characters for the passwords configured in controller. |
| U32 clsSecStrongPwdMinLowerCase | 1.3.6.1.4.1.9.9.618.1.5.9 | Unsigned32 | read-write | This object specifies the minimum number of upper case characters for the passwords configured in controller. |
| U32 clsSecStrongPwdMinDigits | 1.3.6.1.4.1.9.9.618.1.5.10 | Unsigned32 | read-write | This object specifies the minimum number of digits for the passwords configured in controller. |
| U32 clsSecStrongPwdMinSpecialChar | 1.3.6.1.4.1.9.9.618.1.5.11 | Unsigned32 | read-write | This object specifies the minimum special characters for the passwords configured in controller. |
| T/F clsSecWlanCCEnable | 1.3.6.1.4.1.9.9.618.1.5.12 | TruthValue | read-only | This object represents whether WLAN common criteria is enabled or disabled. A value of 'true' indicates that, WLAN common criteria is enabled. A value of 'false' indicates that, WLAN common criteria is disabled. |
| T/F clsSecUcaplEnable | 1.3.6.1.4.1.9.9.618.1.5.13 | TruthValue | read-only | This object represents whether UCAPL is enabled or disabled. A value of 'true' indicates that, UCAPL is enabled. A value of 'false' indicates that, UCAPL is disabled. |
| T/F clsSecMgmtUsrLockoutEnable | 1.3.6.1.4.1.9.9.618.1.5.14 | TruthValue | read-write | This object specifies whether lockout for the management user is enabled or disabled. A value of 'true'indicates that, lockout for the management user is enabled. A value of 'false' indicates that, lockout for the management user is disabled. |
| U32 clsSecMgmtUsrLockoutTime | 1.3.6.1.4.1.9.9.618.1.5.15 | Unsigned32 | read-write | This object specifies the lockout time for the management user configured in controller. |
| U32 clsSecMgmtUsrLockoutAttempts | 1.3.6.1.4.1.9.9.618.1.5.16 | Unsigned32 | read-write | This object specifies the lockout attempts for the management user configured in controller. |
| T/F clsSecSnmpv3UsrLockoutEnable | 1.3.6.1.4.1.9.9.618.1.5.17 | TruthValue | read-write | This object specifies whether the lockout for the SNMP version3 user is enabled or disabled. A value of 'true' indicates that, lockout for the SNMPV3 user is enabled. A value of 'false' indicates that, lockout for the SNMPV3 user is disabled. |
| U32 clsSecSnmpv3UsrLockoutTime | 1.3.6.1.4.1.9.9.618.1.5.18 | Unsigned32 | read-write | This object specifies the lockout time for the SNMP v3 user configured in controller. |
| U32 clsSecSnmpv3UsrLockoutAttempts | 1.3.6.1.4.1.9.9.618.1.5.19 | Unsigned32 | read-write | This object specifies the lockout attempts for the SNMP v3 user configured in controller. |
| U32 clsSecMgmtUsrLockoutLifetime | 1.3.6.1.4.1.9.9.618.1.5.20 | Unsigned32 | read-write | This object specifies the lockout life time for the management user configured in controller. |
| U32 clsSecSnmpv3UsrLockoutLifetime | 1.3.6.1.4.1.9.9.618.1.5.21 | Unsigned32 | read-write | This object specifies the lockout life time for the SNMPV3 user configured in controller. |
| ciscoLwappSysMIBNotifObjects | 1.3.6.1.4.1.9.9.618.1.6 | |||
| STR clsSecStrongPwdManagementUser | 1.3.6.1.4.1.9.9.618.1.6.1 | SnmpAdminString | read-only | This object represents the management user who enabled or disabled the strong password checks. |
| INT clsSecStrongPwdCheckType | 1.3.6.1.4.1.9.9.618.1.6.2 | INTEGER | read-only | This object represents the type of the check that was enabled or disabled by the management user. A value of 'caseCheck' indicates that, the caseCheck was enabled or disabled by the management user. A value of 'consecutiveCheck' indicates that, the consecutiveCheck was enabled or disabled by the management user. A value of 'defaultCheck' indicates that, the defaultCheck was enabled or disabled by the management user. A value of 'usernameCheck' indicates that, the usernameCheck was enabled or disabled by the management user. A value of 'allChecks' indicates that, all checks were enabled by the management user. |
| T/F clsSecStrongPwdCheckOption | 1.3.6.1.4.1.9.9.618.1.6.3 | TruthValue | read-only | This object represents whether the strong password check was enabled/disabled. |
| T/F clsSysAlarmSet | 1.3.6.1.4.1.9.9.618.1.6.4 | TruthValue | accessible-for-notify | This object represents whether this system alarm is raise or clear. A value of 'true' indicates that, this event is enabled. A value of 'false' indicates that, this even is disabled. |
| T/F clsSysMaxThresholdReachedClear | 1.3.6.1.4.1.9.9.618.1.6.5 | TruthValue | accessible-for-notify | This object represents whether this event is raise or clear. A value of 'true' indicates that, this event is cleared A value of 'false' indicates that, this event is raised. |
| INT clsTransferCfgAnalyzeResult | 1.3.6.1.4.1.9.9.618.1.6.6 | INTEGER | accessible-for-notify | This object represents the config file analyze result. A value of unknown indicates that, unknown error. A value of keyMismatch indicates that, the encrypt key mismatch. A value of fileMissing indicates that, the config file missing. A value of contentMismatch indicates that, the file is not intended for this product. |
| STR clsWlcSwVersionBeforeUpgrade | 1.3.6.1.4.1.9.9.618.1.6.7 | SnmpAdminString | accessible-for-notify | This object represents the wlc software version info before upgrading fail. |
| STR clsWlcSwVersionAfterUpgrade | 1.3.6.1.4.1.9.9.618.1.6.8 | SnmpAdminString | accessible-for-notify | This object represents the wlc software version info after upgrading fail. |
| INT clsWlcUpgradeFailReason | 1.3.6.1.4.1.9.9.618.1.6.9 | INTEGER | accessible-for-notify | This object represents the wlc upgrade fail reason. A value of unknownReason indicates that, reason is unknown. A value of fileTypeMismatch indicates that, mismatch in the file extension. please check whether the extension is .aes. A value of fileCheckFail indicates that, file check fail, please check whether the image is correct. A value of fileBackupToFlashFail indicates that, flash backup fail, please check whether the flash space is enough. |
| INE clsPortNumber | 1.3.6.1.4.1.9.9.618.1.6.10 | InetPortNumber | read-only | This object represents port number of MGIG port. |
| U32 clsPortSpeed | 1.3.6.1.4.1.9.9.618.1.6.11 | Unsigned32 | read-only | This object represents port speed (Mbps) of MGIG Port. |
| U32 clsPortSlot | 1.3.6.1.4.1.9.9.618.1.6.12 | Unsigned32 | read-only | This object represents slot number where MGIG port is present. |
| ciscoLwappSysMIBNotifControlObjects | 1.3.6.1.4.1.9.9.618.1.7 | |||
| T/F clsSecStrongPwdCheckTrapEnabled | 1.3.6.1.4.1.9.9.618.1.7.1 | TruthValue | read-write | This object specifies whether the ciscoLwappStrongPwdCheck notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappStrongPwdCheck notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappStrongPwdCheck notification. |
| T/F clsMaxClientsTrapEnabled | 1.3.6.1.4.1.9.9.618.1.7.2 | TruthValue | read-write | This object specifies whether the ciscoLwappMaxClientsReached notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappMaxClientsReached notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappMaxClientsReached notification. |
| T/F clsMaxRFIDTagsTrapEnabled | 1.3.6.1.4.1.9.9.618.1.7.3 | TruthValue | read-write | This object specifies whether the ciscoLwappMaxRFIDTagsReached notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappMaxRFIDTagsReached notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappMaxRFIDTagsReached notification. |
| T/F clsNacAlertTrapEnabled | 1.3.6.1.4.1.9.9.618.1.7.4 | TruthValue | read-write | This object specifies whether the Nac alert association/disassociation notification would be generated. A value of 'true' indicates that, the agent generates nac alert notification. A value of 'false' indicates that, the agent doesn't generates nac alert notification. |
| T/F clsMfpTrapEnabled | 1.3.6.1.4.1.9.9.618.1.7.5 | TruthValue | read-write | This object specifies whether the mfp trap notification would be generated. A value of 'true' indicates that, the agent generates mfp notification. A value of 'false' indicates that, the agent doesn't generates mfp notification. |
| clsSysInfo | 1.3.6.1.4.1.9.9.618.1.8 | |||
| U32 clsSysFlashSize | 1.3.6.1.4.1.9.9.618.1.8.1 | Unsigned32 | read-only | This object represents the total flash memory size in Kbytes. |
| STR clsSysMemoryType | 1.3.6.1.4.1.9.9.618.1.8.2 | SnmpAdminString | read-only | This object represents the system memory type. |
| U32 clsSysMaxClients | 1.3.6.1.4.1.9.9.618.1.8.3 | Unsigned32 | read-only | This object represents max associated clients supported per WLC |
| U32 clsSysApConnectCount | 1.3.6.1.4.1.9.9.618.1.8.4 | Unsigned32 | read-only | This object represents the count of AP's that are connected with WLC |
| STR clsSysNetId | 1.3.6.1.4.1.9.9.618.1.8.5 | SnmpAdminString | read-write | This object specifies the SysNetId which is the numeric string to identify the system information like SysName |
| U32 clsSysCurrentMemoryUsage | 1.3.6.1.4.1.9.9.618.1.8.6 | Unsigned32 | read-only | This object represents the current percent usage of system memory. This MIB object should be updated every clsSysStatsSamplingInterval. |
| U32 clsSysAverageMemoryUsage | 1.3.6.1.4.1.9.9.618.1.8.7 | Unsigned32 | read-only | This object represents the average percent usage of system memory. The memory average usage should be the average of memory-Usage during the time window specified by clsSysStatsAverageInterval. |
| U32 clsSysCurrentCpuUsage | 1.3.6.1.4.1.9.9.618.1.8.8 | Unsigned32 | read-only | This object represents the current percent usage of all CPUs. This MIB should be updated every clsSysStatsSamplingInterval. |
| U32 clsSysAverageCpuUsage | 1.3.6.1.4.1.9.9.618.1.8.9 | Unsigned32 | read-only | This object represents the average percent CPU usage. The average CPU usage should be the average of CPU-Usage during the time window specified by clsSysStatsAverageInterval. |
| STR clsSysCpuType | 1.3.6.1.4.1.9.9.618.1.8.10 | SnmpAdminString | read-only | This object represents the cpu type. |
| U32 clsMaxRFIDTagsCount | 1.3.6.1.4.1.9.9.618.1.8.11 | Unsigned32 | read-only | This object represents the maximum RFID tags present on the controller. |
| U32 clsMaxClientsCount | 1.3.6.1.4.1.9.9.618.1.8.12 | Unsigned32 | read-only | This object represents the maximum clients present on the controller. |
| C32 clsApAssocFailedCountEx | 1.3.6.1.4.1.9.9.618.1.8.13 | Counter32 | read-only | This object represents the count when Access Point failed to associate with the controller. |
| U32 clsCurrentPortalClientCount | 1.3.6.1.4.1.9.9.618.1.8.14 | Unsigned32 | read-only | This object represents the current portal clients present on the controller. |
| U32 clsCurrentOnlineUsersCount | 1.3.6.1.4.1.9.9.618.1.8.15 | Unsigned32 | read-only | This object represents the current all online clients present on the controller. |
| U32 clsSysAbnormalOfflineCount | 1.3.6.1.4.1.9.9.618.1.8.16 | Unsigned32 | read-only | This object represents the abnormal offline count for the wlc. |
| STR clsSysFlashType | 1.3.6.1.4.1.9.9.618.1.8.17 | SnmpAdminString | read-only | This object represents the system Flash type. |
| U32 clsSysOpenUsersCount | 1.3.6.1.4.1.9.9.618.1.8.18 | Unsigned32 | read-only | This object represents the current all online open authentication clients present on the controller. |
| U32 clsSysWepPskUsersCount | 1.3.6.1.4.1.9.9.618.1.8.19 | Unsigned32 | read-only | This object represents the current all online wep/psk authentication clients present on the controller. |
| U32 clsSysPeapSimUsersCount | 1.3.6.1.4.1.9.9.618.1.8.20 | Unsigned32 | read-only | This object represents the current all online peap/sim authentication clients present on the controller. |
| C32 clsSysPeapSimReqCount | 1.3.6.1.4.1.9.9.618.1.8.21 | Counter32 | read-only | This object represents the PEAP/SIM request on the controller. |
| C32 clsSysPeapSimReqSuccessCount | 1.3.6.1.4.1.9.9.618.1.8.22 | Counter32 | read-only | This object represents the successful PEAP/SIM request on the controller. |
| C32 clsSysPeapSimReqFailureCount | 1.3.6.1.4.1.9.9.618.1.8.23 | Counter32 | read-only | This object represents the failed PEAP/SIM request on the controller. |
| STR clsSysNasId | 1.3.6.1.4.1.9.9.618.1.8.24 | SnmpAdminString | read-write | This object specifies the SysNasId. NasId is used to support Roaming, location-based service. |
| I32 clsSysCoChannelTrapRssiThreshold | 1.3.6.1.4.1.9.9.618.1.8.25 | Integer32 | read-write | This object specifies the minimum value of RSSI considered for the trap of Co-Channel AP. |
| I32 clsSysAdjChannelTrapRssiThreshold | 1.3.6.1.4.1.9.9.618.1.8.26 | Integer32 | read-write | This object specifies the minimum value of RSSI considered for the trap of Adj channel AP |
| I32 clsSysClientTrapRssiThreshold | 1.3.6.1.4.1.9.9.618.1.8.27 | Integer32 | read-write | This object specifies the minimum value of RSSI considered for the trap of client. |
| U32 clsSysCmxActiveConnections | 1.3.6.1.4.1.9.9.618.1.8.28 | Unsigned32 | read-only | This object represents the count of active connections present on the controller. |
| clsLyncInfo | 1.3.6.1.4.1.9.9.618.1.9 | |||
| T/F clsLyncState | 1.3.6.1.4.1.9.9.618.1.9.1 | TruthValue | read-write | This object specifies whether Lync is enabled on system. A value of 'true' indicates that, Lync state is enabled. A value of 'false' indicates that, Lync state is disabled. |
| INE clsLyncPort | 1.3.6.1.4.1.9.9.618.1.9.2 | InetPortNumber | read-write | This object specifies about port number of Lync Service. |
| INT clsLyncProtocol | 1.3.6.1.4.1.9.9.618.1.9.3 | INTEGER | read-write | This object specifies about protocol of Lync Service. A value of http indicates that, lync protocol is http. A value of secure http indicates that, lync protocol is secure http. |
| ciscoLwappSysMIBConform | 1.3.6.1.4.1.9.9.618.2 | |||
| ciscoLwappSysMIBCompliances | 1.3.6.1.4.1.9.9.618.2.1 | |||
| ciscoLwappSysMIBCompliance | 1.3.6.1.4.1.9.9.618.2.1.1 | The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. | ||
| ciscoLwappSysMIBComplianceRev1 | 1.3.6.1.4.1.9.9.618.2.1.2 | The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. | ||
| ciscoLwappSysMIBComplianceRev2 | 1.3.6.1.4.1.9.9.618.2.1.3 | The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1. | ||
| ciscoLwappSysMIBComplianceRev3 | 1.3.6.1.4.1.9.9.618.2.1.4 | The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1. | ||
| ciscoLwappSysMIBComplianceRev4 | 1.3.6.1.4.1.9.9.618.2.1.5 | The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1. | ||
| ciscoLwappSysMIBGroups | 1.3.6.1.4.1.9.9.618.2.2 | |||
| ciscoLwappSysConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.1 | This collection of objects represent the system wide configuration on the controller. | ||
| ciscoLwappSysConfigFileEncryptionGroup | 1.3.6.1.4.1.9.9.618.2.2.2 | This object represents the System encryption configuration on the controller. | ||
| ciscoLwappSysConfigGroupSup1 | 1.3.6.1.4.1.9.9.618.2.2.3 | This collection of objects represents the timzone and syslog configuration on the controller. | ||
| ciscoLwappSysTransferOperationConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.4 | This object represents the System Transfer operation configuration on the controller. | ||
| ciscoLwappSysPortConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.5 | This collection of objects represent the system wide configuration on the controller. | ||
| ciscoLwappSysSecurityConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.6 | This collection of objects represent the system security configuration on the controller. | ||
| ciscoLwappSysIgmpConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.7 | This collection of objects represent the IGMP multicast configuration on the controller. | ||
| ciscoLwappSysSecNotifObjsGroup | 1.3.6.1.4.1.9.9.618.2.2.8 | This collection of objects represent the information carried by the security related notifications sent by the agent to a network management station. | ||
| ciscoLwappSysNotifsGroup | 1.3.6.1.4.1.9.9.618.2.2.9 | This collection of objects represent the system config related notifications sent by the agent to a network management station. | ||
| ciscoLwappSysNotifControlGroup | 1.3.6.1.4.1.9.9.618.2.2.10 | This collection of objects represent the flags to control the generation of notification. | ||
| ciscoLwappSysConfigGroupVer1 | 1.3.6.1.4.1.9.9.618.2.2.11 | This collection of objects represent the system wide configuration on the controller. | ||
| ciscoLwappSysStatsConfigGroup | 1.3.6.1.4.1.9.9.618.2.2.12 | This collection of objects represents the statistics intervals configtation on the controller. | ||
| ciscoLwappSysInfoGroup | 1.3.6.1.4.1.9.9.618.2.2.13 | This collection of objects represent System Information configuration on the controller. | ||
| ciscoLwappLyncInfoGroup | 1.3.6.1.4.1.9.9.618.2.2.14 | This collection of objects represent System Information configuration on the controller. | ||
| ciscoLwappSysMulticastMLDGroup | 1.3.6.1.4.1.9.9.618.2.2.15 | This collection of objects represent Multicast MLD configuration on the controller. | ||
| ciscoLwappSysConfigGroupVer2 | 1.3.6.1.4.1.9.9.618.2.2.16 | This collection of objects represent the system wide configuration on the controller. |
RFC description
System configuration and status for Cisco wireless controllers managing lightweight access points via LWAPP protocol.
Start monitoring Cisco Wireless LAN Controllers (LWAPP-based) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.