All MIBs › CISCO-LWAPP-RRM-MIB
Organization: Cisco Systems Inc.
Last Updated: 2020-10-12
Description: MIB for Radio Resource Management channel assignment, transmit power, and interference monitoring on Cisco LWAPP wireless LAN controllers
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-LWAPP-RRM-MIB?
CISCO-LWAPP-RRM-MIB is a Cisco enterprise MIB for wireless LAN controllers that implements Radio Resource Management (RRM), the automated system that tunes channel assignment, transmit power, and interference avoidance across a fleet of Cisco lightweight access points. It exposes per-radio-type parameters covering coverage hole detection (CHD), voice and data packet thresholds, RSSI thresholds, and dynamic channel assignment (DCA) width settings. Rather than tracking physical component faults, it lets administrators monitor the software-driven RF tuning state of the WLAN, revealing whether voice or data traffic is triggering coverage-hole conditions or whether channel width settings are causing interference and degraded throughput. It is one of a family of related CISCO-LWAPP-* MIBs that together describe the LWAPP controller-to-AP architecture. It is deployed in enterprise and campus Wi-Fi networks running Cisco centralized wireless LAN controllers where RF conditions need continuous automated adjustment. Engineers can download the CISCO-LWAPP-RRM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-RRM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco Wireless LAN Controller (WLC)
- Cisco lightweight access point (LWAPP/CAPWAP)
Monitoring Examples
An administrator would poll clrRrmParametersTable/clrRrmParametersEntry to check clrRrmParametersVoiceRssiThreshold and clrRrmParametersVoicePktCountThreshold against clrRrmParametersDataRssiThreshold and clrRrmParametersDataPktCountThreshold to see whether voice or data traffic on a given radio type is nearing a coverage-hole trigger. Reviewing clrRrmParametersDcaChannelWidth alongside clrRrmParametersChdEnable would clarify whether dynamic channel assignment and coverage-hole detection are active and consistently configured. A radio reporting RSSI values consistently below its configured threshold would flag a coverage gap needing additional access points or power adjustment.
What Can Be Monitored
- coverage hole detection status
- voice/data RSSI thresholds
- voice/data packet count and percent thresholds
- dynamic channel assignment width
- pico-cell mode setting
This MIB depends on
Related MIBs
Imported Objects
From CISCO-LWAPP-AP-MIB
| cLApName | OBJECT-TYPE |
From CISCO-LWAPP-DOT11-CLIENT-MIB
| cldcApMacAddress | OBJECT-TYPE |
| cldcClientMacAddress | OBJECT-TYPE |
| cldcIfType | OBJECT-TYPE |
From CISCO-LWAPP-TC-MIB
| CLApIfType |
From CISCO-LWAPP-WLAN-MIB
| cLWlanChdEnable | OBJECT-TYPE |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF ciscoLwappDot11ClientCoverageHolePreAlarm | 1.3.6.1.4.1.9.9.615.0.1 | This notification is generated when the AP receives at least 'packet count' packets, represented by clrRrmParametersVoicePktCount for voice or clrRrmParametersDataPktCount for data, from a client in any given 5 second interval and 'packet percent' of the packets, represented by clrRrmParametersVoicePktCount for voice and clrRrmParametersDataPktCount for data, from the client are below the 'RSSI threshold' represented by clrRrmParametersVoiceRssiThreshold for voice and clrRrmParametersDataRssiThreshold for data. | ||
| NTF ciscoLwappDot11ClientCoverageHolePreAlarmRev | 1.3.6.1.4.1.9.9.615.0.5 | The system generates this notification when the RRM coverage hole detection algorithm detects areas of radio coverage in a wireless LAN that are below the level needed for robust radio performance. If clients on a access point are detected at threshold levels (RSSI, percentage of failed packets, and number of failed packets) specified in RRM configuration, the access point sends a 'coverage hole' alert to the controller. This notification is generated in any of the following conditions 1)When the failed packet count is more than failed packet count threshold represented by clrRrmParametersVoicePktCountThreshold for voice and clrRrmParametersDataPktCountThreshold for data. 2)When the percentage of failed packet count is more than the failed packet count threshold represented by clrRrmParametersVoicePktPercentThreshold for voice and clrRrmParametersDataPktPercentThreshold for data. 3)When RSSI value is lower than the RSSI threshold represented by clrRrmParametersVoiceRssiThreshold for voice and clrRrmParametersDataRssiThreshold for data. | ||
| ciscoLwappRrmChannelStatusGroup | 1.3.6.1.4.1.9.9.615.2.2.7 | A collection of objects providing creation or deletion of 802.11 channels. | ||
| ciscoLwappRrmChdConfigGroup | 1.3.6.1.4.1.9.9.615.2.2.14 | This collection of objects represent the Coverage Hold Detection(CHD) configuration on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmConfigGroup | 1.3.6.1.4.1.9.9.615.2.2.1 | This collection of objects represent the RRM configuration on the controller. ciscoLwappRrmConfigGroup object is superseded by ciscoLwappRrmConfigGroupSup1 . | ||
| ciscoLwappRrmConfigGroupSup1 | 1.3.6.1.4.1.9.9.615.2.2.2 | This collection of objects represents the RRM configuration for Voice and Data packets on the controller. | ||
| ciscoLwappRrmConfigGroupSup2 | 1.3.6.1.4.1.9.9.615.2.2.3 | This collection of objects represent the RRM configuration on the controller. | ||
| ciscoLwappRrmConfigGroupSup3 | 1.3.6.1.4.1.9.9.615.2.2.4 | This collection of objects represent the Transmission Power Control(TPC) configuration on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmConfigGroupSup4 | 1.3.6.1.4.1.9.9.615.2.2.5 | This collection of objects represent the RRM RF Grouping configuration on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmConfigGroupSup5 | 1.3.6.1.4.1.9.9.615.2.2.11 | This collection of objects represent the RRM configuration on the controller. | ||
| ciscoLwappRrmConfigGroupSup6 | 1.3.6.1.4.1.9.9.615.2.2.13 | This collection of objects represent the RRM configuration on the controller. | ||
| ciscoLwappRrmConfigGroupSup7 | 1.3.6.1.4.1.9.9.615.2.2.18 | This collection of objects represent the RRM configuration on the controller. | ||
| ciscoLwappRrmConfigGroupSup8 | 1.3.6.1.4.1.9.9.615.2.2.19 | This collection of objects represent the RRM Dca configuration on the controller. | ||
| ciscoLwappRrmConfigGroupSup9 | 1.3.6.1.4.1.9.9.615.2.2.20 | This collection of objects represents RRM Grouping configuration corresponding to dot11 band of APs joined to the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmDcaChannelListGroup | 1.3.6.1.4.1.9.9.615.2.2.10 | This collection of objects represent the channels used in DCA as well as not used in DCA for APs. | ||
| ciscoLwappRrmFraConfigGroup | 1.3.6.1.4.1.9.9.615.2.2.12 | This collection of objects represent the Flexible Radio Assignment (FRA) configuration on the controller. | ||
| ciscoLwappRrmGrpStatusGroup | 1.3.6.1.4.1.9.9.615.2.2.6 | This collection of objects represent the status of RRM RF Groping on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmMIB | 1.3.6.1.4.1.9.9.615 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is used to study the RRM on the WLAN. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Radio Resource Management ( RRM ) RRM is the system level control of co-channel interference and other radio transmission characteristics in wireless communication systems. Received Signal Strength Indicator ( RSSI ) A measure of the strength of the signal as observed by the entity that received it, expressed in 'dbm'. Coverage Hole Detection ( CHD ) If clients on an Access Point are detected at low RSSI levels, it is considered a coverage hole by the Access Points. This indicates the existence of an area where clients are continually getting poor signal coverage, without having a viable location to roam to. Dynamic Channel Assignment (DCA) Dynamic channel assignment (DCA) is used by the controller to minimize adjacent channel interference between access points. BSS Color Optimization (BCO) BCO is used by the controller to minimize BSS color collisions between access points. Dynamic Frequency Selection (DFS) Dynamic frequency selection (DFS) is used by the controller to detect radar signals and avoid interfering with them. RRM RF Grouping Radio Resource Management (RRM) allows the Cisco WLAN controllers to continuously analyze the existing RF environments, and automatically adjust the AP power and channel configurations in order to help alleviate overlapping channel interference, signal coverage problems, and so forth. An RF group is a cluster of Cisco wireless controllers that coordinates its RRM calculations on a per 802.11-network basis. An RF group exists for each 802.11 network type. Clustering controllers into RF groups enables the RRM algorithms to scale beyond a single controller. +....+ Auto-leader +....+ Auto-member + + + C2 + + + (802.11a network) +....+ + C1 + + + + + Static-member +....+ Static-leader + + + C3 + +....+ (802.11b network) +....+ With the help of above diagram, different aspects of RRM RF Grouping can be explained. Grouping can be configured for 3 modes. 1) Automatic 2) Static 3) Off If the mode is 'Automatic', the controllers automatically form groups and elect leaders to perform better dynamic parameter optimization. If the mode is 'Static', user can select one controller as the group leader and configure the group members manually. If the mode is 'Off', no dynamic grouping occurs. Each controller optimizes only its own APs' parameters. In the above diagram, controller C1 forms a RF group with controller C2 in 802.11a network. And with controller C3, it forms a different group in 802.11b network. For the 802.11a network, the group mode is selected as 'Automatic'. So between C1 and C2 controllers, one would be selected as group leader and the other controller as member automatically by the algorithm. In the above case C1 is the group leader and C2 is the group member. Now for 802.11b network, group mode is selected as 'Static'. Also the user has manually configured C3 as the leader in this group and C1 was added to this group as member. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol | ||
| ciscoLwappRrmMIBCompliance | 1.3.6.1.4.1.9.9.615.2.1.1 | The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module. | ||
| ciscoLwappRrmMIBComplianceRev1 | 1.3.6.1.4.1.9.9.615.2.1.2 | The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module. | ||
| ciscoLwappRrmMIBComplianceRev2 | 1.3.6.1.4.1.9.9.615.2.1.3 | The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module. | ||
| ciscoLwappRrmMIBComplianceRev3 | 1.3.6.1.4.1.9.9.615.2.1.4 | The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module. | ||
| ciscoLwappRrmMIBComplianceRev4 | 1.3.6.1.4.1.9.9.615.2.1.5 | The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module. | ||
| ciscoLwappRrmMIBCompliances | 1.3.6.1.4.1.9.9.615.2.1 | |||
| ciscoLwappRrmMIBConform | 1.3.6.1.4.1.9.9.615.2 | |||
| ciscoLwappRrmMIBGroups | 1.3.6.1.4.1.9.9.615.2.2 | |||
| ciscoLwappRrmMIBNotifs | 1.3.6.1.4.1.9.9.615.0 | |||
| ciscoLwappRrmMIBObjects | 1.3.6.1.4.1.9.9.615.1 | |||
| ciscoLwappRrmNotifsGroup | 1.3.6.1.4.1.9.9.615.2.2.9 | This collection of objects provides the information about the notifications sent by the agent related to RRM. | ||
| ciscoLwappRrmNotifyObjectsGroup | 1.3.6.1.4.1.9.9.615.2.2.17 | This collection of objects provide the information about RRM trap configuration and trap definition. These objects are defined under ciscoLwappRrmNotifObjects. | ||
| ciscoLwappRrmOptRoamGroup | 1.3.6.1.4.1.9.9.615.2.2.15 | This collection of objects represent the Optimized Roaming configuration on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmPakRssiConfigGroup | 1.3.6.1.4.1.9.9.615.2.2.16 | This collection of objects represent the Packet RSSI configuration on the controller, when the same is enabled on the controller. | ||
| ciscoLwappRrmParametersGroup | 1.3.6.1.4.1.9.9.615.2.2.8 | This collection of objects represent the RRM parameters for a 802.11 interface type. | ||
| NTF ciscoLwappRrmRfGroupLeaderChange | 1.3.6.1.4.1.9.9.615.0.2 | This notification would be generated, from the controller that is elected as the new leader, when RF Grouping is done. It has MAC address and details of the new Group Leader. | ||
| NTF ciscoLwappRrmRfGroupLeaderChangeRev | 1.3.6.1.4.1.9.9.615.0.6 | This notification would be generated, from the controller that is elected as the new leader, when RF Grouping is done. It has MAC address and details of the new Group Leader. | ||
| NTF ciscoLwappRrmRfGroupMemberAdded | 1.3.6.1.4.1.9.9.615.0.3 | This notification is generated from the group leader when a new member is added to the RF group. This notification has MAC address and details of new group member. | ||
| NTF ciscoLwappRrmRfGroupMemberAddedRev | 1.3.6.1.4.1.9.9.615.0.7 | This notification is generated from the group leader when a new member is added to the RF group. This notification has MAC address and details of new group member. | ||
| NTF ciscoLwappRrmRfGroupMemberRemoved | 1.3.6.1.4.1.9.9.615.0.4 | The notification is generated from the group leader, when a member is removed from the RF group. This notification has MAC address and details of removed group member. | ||
| NTF ciscoLwappRrmRfGroupMemberRemovedRev | 1.3.6.1.4.1.9.9.615.0.8 | The notification is generated from the group leader, when a member is removed from the RF group. This notification has MAC address and details of removed group member. | ||
| INT clRrmBcoMode | 1.3.6.1.4.1.9.9.615.1.1.16.1.1 | INTEGER | read-write | BSS Color Optimization (BCO) has two modes. When the mode is auto, the BSS color will be dynamically updated for all access points that permit this operation. When BCO is static, no dynamic BSS color selections occur and the BSS color must be manually configured. |
| clrRrm11kConfig | 1.3.6.1.4.1.9.9.615.1.1.12 | |||
| U32 clrRrm11kDenialMax | 1.3.6.1.4.1.9.9.615.1.1.12.1 | Unsigned32 | read-write | This object specifies the maximum number of times a client can be denied association if the association request that is sent to an AP does not match any AP in the prediction list. |
| U32 clrRrm11kFloorBias | 1.3.6.1.4.1.9.9.615.1.1.12.2 | Unsigned32 | read-write | This object specifies the neighbor floor label bias in dBm. |
| U32 clrRrm11kPredictionMin | 1.3.6.1.4.1.9.9.615.1.1.12.3 | Unsigned32 | read-write | This object specifies the minimum number of predicted APs required for the prediction list feature to be activated. |
| clrRrmAddChannelEntry | 1.3.6.1.4.1.9.9.615.1.1.14.1 | not-accessible | Each entry in this table provides the added channel information to the default DCA channel list for an 802.11 interface in an AP. | |
| U32 clrRrmAddChannelNum | 1.3.6.1.4.1.9.9.615.1.1.14.1.1 | Unsigned32 | not-accessible | The channel nubmer for this entry. This value represents the unique channel number added to the default DCA channel list on this 802.11 interface for this regulatory domain. |
| ROW clrRrmAddChannelRowStatus | 1.3.6.1.4.1.9.9.615.1.1.14.1.3 | RowStatus | read-create | The status of this conceptual row. All writable objects in this row may be modified at any time. |
| clrRrmAddChannelTable | 1.3.6.1.4.1.9.9.615.1.1.14 | not-accessible | This table represents the added channel information to the default DCA channel list for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can add a non-default DCA channel to this list and those channels will be put in this table. This table represents the added DCA channels information to the default DCA list. By default, there will not be any entries in this table. An entry can also be created or deleted by using clrRrmChannelRowStatus. | |
| T/F clrRrmAddedChannelDcaState | 1.3.6.1.4.1.9.9.615.1.1.14.1.2 | TruthValue | read-create | This object specifies whether this channel is part of the dynamic channel allocation (DCA) Add List. A value of 'true' indicates that the DCA for this channel is enabled. |
| I32 clrRrmApTransmitPowerLevel | 1.3.6.1.4.1.9.9.615.1.2.1 | Integer32 | accessible-for-notify | This indicates represents the transmit power level for the AP. |
| clrRrmBcoEntry | 1.3.6.1.4.1.9.9.615.1.1.16.1 | not-accessible | An entry in this table represents the BSS Color Optimization (BCO) configuration for a dot11 band. | |
| clrRrmBcoTable | 1.3.6.1.4.1.9.9.615.1.1.16 | not-accessible | This table contains configurations for the BSS Color Optimization (BCO) algorithm. | |
| T/F clrRrmChannelDcaState | 1.3.6.1.4.1.9.9.615.1.1.4.1.2 | TruthValue | read-create | This object indicates whether this channel is part of the dynamic channel allocation (DCA) list. A value of 'true' indicates that the DCA for this channel is enabled. A value of 'false' indicates that the DCA for this channel is disabled. |
| clrRrmChannelEntry | 1.3.6.1.4.1.9.9.615.1.1.4.1 | not-accessible | Each entry in this table provides the channel information for an 802.11 interface in an AP. | |
| U32 clrRrmChannelNum | 1.3.6.1.4.1.9.9.615.1.1.4.1.1 | Unsigned32 | not-accessible | The channel nubmer for this entry. This value represents the unique channel number on this 802.11 interface for this regulatory domain. |
| ROW clrRrmChannelRowStatus | 1.3.6.1.4.1.9.9.615.1.1.4.1.3 | RowStatus | read-create | The status of this conceptual row.clrRrmChannelNum and clrRrmChannelDcaState are mandatory for create and go of rowstatus.All writable objects in this row may be modified at any time. |
| clrRrmChannelTable | 1.3.6.1.4.1.9.9.615.1.1.4 | not-accessible | This table represents the channel information for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. This table represents this information. Entries are automatically created on the controller as APs associate. Entries are removed when the APs disassociate. | |
| INT clrRrmClientType | 1.3.6.1.4.1.9.9.615.1.2.3 | INTEGER | accessible-for-notify | This object indicates the client type for which this notification was sent. data(1) - coverage hole has been detected for a data client(client which is meant for data services). voice(2) - coverage hole has been detected for a voice client(client which is meant for voice services). |
| clrRrmConfig | 1.3.6.1.4.1.9.9.615.1.1 | |||
| clrRrmDcaChannelListEntry | 1.3.6.1.4.1.9.9.615.1.1.9.1 | not-accessible | Each entry in this table provides list of the channels that are used in DCA as well as not-used in DCA for an 802.11 interface in an AP. | |
| clrRrmDcaChannelListTable | 1.3.6.1.4.1.9.9.615.1.1.9 | not-accessible | This table contains current channel information for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. This table represents this information. Entries are automatically created on the controller as APs associate. Entries are removed when the APs disassociate. User can add a channel in DCA or remove it from DCA using the clrRrmChannelTable. clrRrmDcaChannelListTable provides the list of current channels allocation for DCA. | |
| clrRrmDcaConfig | 1.3.6.1.4.1.9.9.615.1.1.7 | |||
| STR clrRrmDcaDefaultChannelList | 1.3.6.1.4.1.9.9.615.1.1.9.1.3 | SnmpAdminString | read-only | This object provides the default DCA channels based on configured country code/country code list. This is a comma separated list of default DCA channel numbers. |
| T/F clrRrmDcaDot11aOutdoorAPDca | 1.3.6.1.4.1.9.9.615.1.1.7.1 | TruthValue | read-write | This object specifies whether check for non-DFS channel should be done on DCA channel list or not. Generally at least one non-DFS channel should be present in DCA channel list. But there are locations like EU(European Union) where there is no non-DFS channel available for outdoor deployment. Customers deploying outdoor APs in EU or regions with similar regulations should set this variable to 'true'. A value of 'true' indicates that controller will not perform check for non-DFS channels in DCA list. A value of 'false' indicates that controller will perform checkf for non-DFS channels in DCA list. |
| STR clrRrmDcaUnusedChannelList | 1.3.6.1.4.1.9.9.615.1.1.9.1.2 | SnmpAdminString | read-only | This object represents the channels that are not part of the Dynamic Channel Allocation (DCA) list. This is a comma separated list of unused channel numbers. |
| STR clrRrmDcaUsedChannelList | 1.3.6.1.4.1.9.9.615.1.1.9.1.1 | SnmpAdminString | read-only | This object represents the channels that are part of the Dynamic Channel Allocation (DCA) list. This is a comma separated list of used channel numbers. |
| clrRrmDot11BandGrpEntry | 1.3.6.1.4.1.9.9.615.1.1.5.1 | not-accessible | An entry in this table represents the RRM RF grouping on a dot11 band of an AP that has joined the controller. For each dot11 band an entry will be created. | |
| U32 clrRrmDot11BandGrpInterval | 1.3.6.1.4.1.9.9.615.1.1.5.1.8 | Unsigned32 | read-only | This object represents the period used by the grouping algorithm. The grouping algorithm runs when the group contents changes and automatic grouping is enabled. The system administrator can start grouping on demand. |
| U32 clrRrmDot11BandGrpLastUpdateTime | 1.3.6.1.4.1.9.9.615.1.1.5.1.7 | Unsigned32 | read-only | This object represents the last time the dot11 grouping was updated on this controller. This is valid only if the controller is not a static member in the group. If it is a static member (i.e the value of the variable ,'clrRrmDot11BandGrpMode' is 'static-member(4)'), a value of '0' would be returned always. |
| IP clrRrmDot11BandGrpLeaderIpAddress | 1.3.6.1.4.1.9.9.615.1.1.5.1.2 | InetAddress | read-only | This object represents the configured group leader's address for the dot11 group containing this controller. |
| IPt clrRrmDot11BandGrpLeaderIpAddressType | 1.3.6.1.4.1.9.9.615.1.1.5.1.1 | InetAddressType | read-only | This object represents the group leader's address type for the dot11 group containing this controller. The only one address type supported is ipv4(1). |
| IP clrRrmDot11BandGrpLeaderIpv6Address | 1.3.6.1.4.1.9.9.615.1.1.5.1.10 | InetAddress | read-only | This object represents the IPv6 address of the RRM RF group leader. |
| IPt clrRrmDot11BandGrpLeaderIpv6AddressType | 1.3.6.1.4.1.9.9.615.1.1.5.1.9 | InetAddressType | read-only | This object represents the IP address type of the RRM RF group leader. |
| STR clrRrmDot11BandGrpLeaderName | 1.3.6.1.4.1.9.9.615.1.1.5.1.3 | SnmpAdminString | read-only | This object represents the name of the current group leader. |
| clrRrmDot11BandGrpMemberEntry | 1.3.6.1.4.1.9.9.615.1.1.6.1 | not-accessible | An entry describes the grouping members on a dot11 band of an AP that has joined the controller. An entry will be created/deleted when members are added/deleted to/from the gorup. | |
| clrRrmDot11BandGrpMemberTable | 1.3.6.1.4.1.9.9.615.1.1.6 | not-accessible | This table contains the information about the RRM grouping members corresponding to the dot11 band of the APs that have joined the controller. The entries are members of the group represented by clrRrmDot11BandGrpTable. | |
| INT clrRrmDot11BandGrpMode | 1.3.6.1.4.1.9.9.615.1.1.5.1.4 | INTEGER | read-write | This object specifies the mode for the RRM algorithm for the band. 'automatic' - the controller form groups and elect leaders to perform better dynamic parameter optimization. 'leader' - the user can manually configure the group. 'off' - no dynamic grouping occurs. Each controller optimizes only its own APs' parameters. |
| T/F clrRrmDot11BandGrpRestart | 1.3.6.1.4.1.9.9.615.1.1.5.1.6 | TruthValue | read-write | This object specifies whether the grouping algorithm needs a restart. If a value of 'true' is set, the RRM grouping algorithm is restarted for the dot11 band. This will always return 'false' when retrieved |
| INT clrRrmDot11BandGrpRole | 1.3.6.1.4.1.9.9.615.1.1.5.1.5 | INTEGER | read-only | This object represents the group role with respect to RRM RF grouping. The controller can be either group member or group leader while being in automatic or static grouping, for a particular band. If grouping is off , the value of the group role would be 'none'. 'none' - RRM RF Grouping is off 'auto-leader' - leader of automatic RRM RF Group 'auto-member' - member in automatic RRM RF Group 'static-leader' - leader of static RRM RF Group 'static-member' - member in static RRM RF Group. |
| clrRrmDot11BandGrpTable | 1.3.6.1.4.1.9.9.615.1.1.5 | not-accessible | This table contains the information about the RRM grouping corresponding to the dot11 band of the APs that have joined the controller. This table has a one-to-one dependent relationship on the clrRrmParametersTable. | |
| clrRrmDot11BandJoinedGrpMemberEntry | 1.3.6.1.4.1.9.9.615.1.1.15.1 | not-accessible | An entry describes the grouping members on a dot11 band of an AP that has joined the controller. An entry will be created/deleted when members are added/deleted to/from the gorup. | |
| clrRrmDot11BandJoinedGrpMemberTable | 1.3.6.1.4.1.9.9.615.1.1.15 | not-accessible | This table contains the information about the RRM grouping members corresponding to the dot11 band of the APs that have joined the controller. The entries are members of the group represented by clrRrmDot11BandGrpTable. | |
| IP clrRrmDot11BandJoinedMemberIpAddress | 1.3.6.1.4.1.9.9.615.1.1.15.1.2 | InetAddress | not-accessible | This object represents the address of the dot11 group member for the dot11 grouping containing this controller. |
| IPt clrRrmDot11BandJoinedMemberIpAddressType | 1.3.6.1.4.1.9.9.615.1.1.15.1.1 | InetAddressType | not-accessible | This object indicates the address type of the dot11 group member for the dot11 grouping containing this controller. |
| IP clrRrmDot11BandJoinedMemberIpv6Address | 1.3.6.1.4.1.9.9.615.1.1.15.1.7 | InetAddress | not-accessible | This object indicates the IPv6 address of the member controller joined to the RRM RF group. |
| IPt clrRrmDot11BandJoinedMemberIpv6AddressType | 1.3.6.1.4.1.9.9.615.1.1.15.1.6 | InetAddressType | not-accessible | This object indicates the IP address type of the member controller joined to the RRM RF group. |
| T/F clrRrmDot11BandJoinedMemberIsJoined | 1.3.6.1.4.1.9.9.615.1.1.15.1.4 | TruthValue | read-only | This object indicates whether the member has joined this RRM RF Group yet. If not the value would be 'false'. Else it would be true. This field is significant only if the current group is a static RRM RF Group. In all other cases a value of 'true' would be shown. true - member has joined the group successfully false - member has not joined the group yet. |
| INT clrRrmDot11BandJoinedMemberJoinFailureReason | 1.3.6.1.4.1.9.9.615.1.1.15.1.5 | INTEGER | read-only | This object indicates the reason the member could not join the RRM RF Group. This field is relevant only if the corresponding instance for 'clrRrmDot11BandMemberIsJoined' is 'false'. joinedSuccessfully - member has joined the group successfully invalidIp - invalid ip groupSizeExceeded - group size is exceeded invalidGroupOrder - group order is invalid nonMatchingGroupID - group id doesn't match unexpectedError - unexpected error has occurred weakSignalStrength - signal strength is weak joinPending - group join is pending notAManager - not a manager groupingDelayed - grouping is delayed groupingDisabled - grouping is disabled invalidProtocolVersion - protocol version is invalid countryCodeMismatch - country code doesn't match invalidHierarchy - invalid grouping hierarchy alreadyAStaticLeader - already a static leader memberOfAnotherGroup - member of another group unconfiguredAsStaticMember - unconfigured static member cntlrNameAndIpMismatch - controller name and ip doesn't match unexpectedMemoryError - an unexpected memory error has happened rfDomainMismatch - RF domain doesn't match. |
| STR clrRrmDot11BandJoinedMemberName | 1.3.6.1.4.1.9.9.615.1.1.15.1.3 | SnmpAdminString | read-only | This object specifies the name of the dot11 group member for the dot11 grouping containing this controller. |
| IP clrRrmDot11BandMemberIpAddress | 1.3.6.1.4.1.9.9.615.1.1.6.1.2 | InetAddress | not-accessible | This object specifies the address of the dot11 group member for the dot11 grouping containing this controller. |
| IPt clrRrmDot11BandMemberIpAddressType | 1.3.6.1.4.1.9.9.615.1.1.6.1.1 | InetAddressType | not-accessible | This object indicates the address type of the dot11 group member for the dot11 grouping containing this controller. |
| T/F clrRrmDot11BandMemberIsJoined | 1.3.6.1.4.1.9.9.615.1.1.6.1.4 | TruthValue | read-only | This object represents whether the member has joined this RRM RF Group yet.If not the value would be 'false'. Else it would be true.This field is significant only if the current group is a static RRM RF Group. In all other cases a value of 'true' would be shown. true - member has joined the group successfully false - member has not joined the group yet. |
| INT clrRrmDot11BandMemberJoinFailureReason | 1.3.6.1.4.1.9.9.615.1.1.6.1.5 | INTEGER | read-only | This object represents the reason the member could not join the RRM RF Group. This field is relevant only if the corresponding instance for 'clrRrmDot11BandMemberIsJoined' is 'false'. joinedSuccessfully - member has joined the group successfully invalidIp - invalid ip groupSizeExceeded - group size is exceeded invalidGroupOrder - group order is invalid nonMatchingGroupID - group id doesn't match unexpectedError - unexpected error has occurred weakSignalStrength - signal strength is weak joinPending - group join is pending notAManager - not a manager groupingDelayed - grouping is delayed groupingDisabled - grouping is disabled invalidProtocolVersion - protocol version is invalid countryCodeMismatch - country code doesn't match invalidHierarchy - invalid grouping hierarchy alreadyAStaticLeader - already a static leader memberOfAnotherGroup - member of another group unconfiguredAsStaticMember - unconfigured static member cntlrNameAndIpMismatch - controller name and ip doesn't match unexpectedMemoryError - an unexpected memory error has happened rfDomainMismatch - RF domain doesn't match. splitForInvalidStateRequest - split for invalid state request transitioningToStaticFromAuto - transitioning to static from auto splitDueToUserAction - split due to user action. |
| STR clrRrmDot11BandMemberName | 1.3.6.1.4.1.9.9.615.1.1.6.1.3 | SnmpAdminString | read-create | This object specifies the name of the dot11 group member for the dot11 grouping containing this controller. |
| ROW clrRrmDot11BandMemberRowStatus | 1.3.6.1.4.1.9.9.615.1.1.6.1.6 | RowStatus | read-create | This object specifies the status of the row. |
| clrRrmFraConfig | 1.3.6.1.4.1.9.9.615.1.1.11 | |||
| T/F clrRrmFraEnable | 1.3.6.1.4.1.9.9.615.1.1.11.1 | TruthValue | read-write | This object specifies the state of Flexible Radio Assignment(FRA)feature. A value of 'true' indicates that FRA is enabled. A value of 'false' indicates that FRA is disabled. |
| I32 clrRrmFraInterval | 1.3.6.1.4.1.9.9.615.1.1.11.2 | Integer32 | read-write | This object specifies the FRA interval in hours for the FRA feature. |
| INT clrRrmFraSensitivity | 1.3.6.1.4.1.9.9.615.1.1.11.3 | INTEGER | read-write | This object specifies the sensitivity for the FRA feature low(1) - set the FRA sensistivity as low(100%). medium(2) - set the FRA sensitivity as medium(95%). high(3) - set the FRA sensitivity as high(90%). higher(4) - set the FRA sensitivity as higher(85%). evenhigher(5) - set the FRA sensitivity as evenhigher(80%). superhigh(6) - set the FRA sensitivity as superhigh(50%). |
| U32 clrRrmFraSensorCoverage | 1.3.6.1.4.1.9.9.615.1.1.11.5 | Unsigned32 | read-only | This object specifies the overall sensor coverage for entire RRM Group. It will represent % of radios covered in the single RF domain. |
| I32 clrRrmFraSensorDensityOptimisationTargetRssi | 1.3.6.1.4.1.9.9.615.1.1.11.7 | Integer32 | read-only | This value specifies receiver size cell for wireless clients. RSSI value in dBm will approximate downlink RSSI for wireless clients. Target RSSI represents rough coverage given by FRA enabled radio for clients. |
| INT clrRrmFraSensorThreshold | 1.3.6.1.4.1.9.9.615.1.1.11.4 | INTEGER | read-write | This object specifies threshold levels for Sensor Selection algorithm. Values offered can influence FRA algorithm's decision to provide less or more sensor radios for WSA service. ClientPriority will ensure highest(default) coverage for wireless clients and SensorPriority offers more sensor radios offered for WSA service, such threshold with weaker coverage for wireless clients. |
| INT clrRrmFraServicePriority | 1.3.6.1.4.1.9.9.615.1.1.11.6 | INTEGER | read-write | This object specifies service priority of flexible radio assignment algorithm.Coverage is the default state which will ensure good coverage for wireless clients. Client-Aware enables more 5GHz radios when network load is higher,Service-Assurance enables more sensors via excessive radios to ensure good sensor coverage for Wireless Service Assurance. |
| T/F clrRrmHyperLocationEnable | 1.3.6.1.4.1.9.9.615.1.1.10.1 | TruthValue | read-write | This object specifies the state of Packet RSSI location feature. A value of 'true' indicates that PRL(Packet RSSI Location) is enabled. A value of 'false' indicates that PRL is disabled. |
| U32 clrRrmNeighborApCount | 1.3.6.1.4.1.9.9.615.1.2.8 | Unsigned32 | accessible-for-notify | This object represents the number of 'clrRrmNeighborApMac, clrRrmNeighborApRssi' appended to this notification. This count is 5 and includes the AP itself. |
| U32 clrRrmNeighborApCountRev | 1.3.6.1.4.1.9.9.615.1.2.15 | Unsigned32 | accessible-for-notify | This object represents the number of 'clrRrmNeighborApMac, clrRrmNeighborApRssi' appended to this notification. |
| STR clrRrmNeighborApIfType | 1.3.6.1.4.1.9.9.615.1.2.11 | SnmpAdminString | accessible-for-notify | This object represents the neighbor AP radio type for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| STR clrRrmNeighborApIfTypeRev | 1.3.6.1.4.1.9.9.615.1.2.18 | SnmpAdminString | accessible-for-notify | This object represents the neighbor AP radio type for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| STR clrRrmNeighborApMacAddress | 1.3.6.1.4.1.9.9.615.1.2.9 | SnmpAdminString | accessible-for-notify | This object represents the neighbor MAC address for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| STR clrRrmNeighborApMacAddressRev | 1.3.6.1.4.1.9.9.615.1.2.16 | SnmpAdminString | accessible-for-notify | This object represents the neighbor MAC address for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| STR clrRrmNeighborApRssi | 1.3.6.1.4.1.9.9.615.1.2.10 | SnmpAdminString | accessible-for-notify | This object represents the neighbor RSSI values for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| STR clrRrmNeighborApRssiRev | 1.3.6.1.4.1.9.9.615.1.2.17 | SnmpAdminString | accessible-for-notify | This object represents the neighbor RSSI values for this client. This is a comma seperated values for clrRrmNeighborApCount values. |
| clrRrmNotificationVariable | 1.3.6.1.4.1.9.9.615.1.2 | |||
| clrRrmPakRssiConfig | 1.3.6.1.4.1.9.9.615.1.1.10 | |||
| IP clrRrmPakRssiNtp | 1.3.6.1.4.1.9.9.615.1.1.10.5 | InetAddress | read-write | This object specifies the NTP server IP for Packet RSSI location feature. |
| IPt clrRrmPakRssiNtpIpAddressType | 1.3.6.1.4.1.9.9.615.1.1.10.4 | InetAddressType | read-write | This object specifies the NTP server IP address type for Packet RSSI location feature. |
| I32 clrRrmPakRssiThreshold | 1.3.6.1.4.1.9.9.615.1.1.10.2 | Integer32 | read-write | This object specifies the threshold value for Packet RSSI location feature. Valid range is -100 dbm to -50 dbm. |
| I32 clrRrmPakRssiThresholdTrigger | 1.3.6.1.4.1.9.9.615.1.1.10.3 | Integer32 | read-write | This object specifies the trigger threshold value for Packet RSSI location feature. Valid range is 1 dbm to 100 dbm. |
| T/F clrRrmParametersChdDevice | 1.3.6.1.4.1.9.9.615.1.1.1.1.18 | TruthValue | read-write | This object specifies the state of device detection on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| T/F clrRrmParametersChdEnable | 1.3.6.1.4.1.9.9.615.1.1.1.1.3 | TruthValue | read-write | This object specifies the state of CHD (Coverage Hole Detection) on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| T/F clrRrmParametersChdInterference | 1.3.6.1.4.1.9.9.615.1.1.1.1.15 | TruthValue | read-write | This object specifies the state of interference on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| T/F clrRrmParametersChdLoad | 1.3.6.1.4.1.9.9.615.1.1.1.1.16 | TruthValue | read-write | This object specifies the state of load on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| T/F clrRrmParametersChdNoise | 1.3.6.1.4.1.9.9.615.1.1.1.1.14 | TruthValue | read-write | This object specifies the state of noise on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| T/F clrRrmParametersChdSignal | 1.3.6.1.4.1.9.9.615.1.1.1.1.17 | TruthValue | read-write | This object specifies the state of signal on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled. |
| INT clrRrmParametersClientNetworkPreference | 1.3.6.1.4.1.9.9.615.1.1.1.1.25 | INTEGER | read-write | This object represents the client network preference. connectivity - RRM Algorithm has a prefereance on connectiviry of the clients throughput - RRM Algorithm has a preference on high thoughput of the clients default - RRM Algorithm has no preference on the clients |
| U32 clrRrmParametersDataPktCountThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.7 | Unsigned32 | read-write | This object specifies the minimum threshold on the Data packet count required to trigger the CHD algorithm on the controller. |
| U32 clrRrmParametersDataPktPercentThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.8 | Unsigned32 | read-write | This object specifies the threshold on the percent of Data packets dropped, that is required to trigger the CHD algorithm on the controller. |
| I32 clrRrmParametersDataRssiThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.9 | Integer32 | read-write | This object specifies the RSSI threshold value for Data packets, that is required to trigger the CHD algorithm on the controller. |
| INT clrRrmParametersDcaChannelWidth | 1.3.6.1.4.1.9.9.615.1.1.1.1.10 | INTEGER | read-write | This object specifies how the system performs DCA channel width selection twenty - 20MHz channel width supported by this radio. forty - 40MHz channel width supported by this radio. eighty - 80MHz channel width supported by this radio. oneSixty - 160MHz channel width supported by this radio. best - Dynamic channel width(160MHz, 80MHz, 40MHz or20MHz) supported by this radio. |
| clrRrmParametersEntry | 1.3.6.1.4.1.9.9.615.1.1.1.1 | not-accessible | An entry in this table corresponds to a particular 802.11 interface type. | |
| U32 clrRrmParametersMaxClients | 1.3.6.1.4.1.9.9.615.1.1.1.1.19 | Unsigned32 | read-write | This object specifies the maximum allowed clients per radio. |
| I32 clrRrmParametersMaxTxPower | 1.3.6.1.4.1.9.9.615.1.1.1.1.11 | Integer32 | read-write | This object specifies the upper limit of transmit power in dBm. For a 802.11a network, the system will only accept this configuration if the bsnGlobalDot11aDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. For a 802.11b network, the system will only accept this configuration if the bsnGlobalDot11bDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. The value of this attribute has to be greater than equal to value of clrRrmParametersMinTxPower. |
| I32 clrRrmParametersMinTxPower | 1.3.6.1.4.1.9.9.615.1.1.1.1.12 | Integer32 | read-write | This object specifies the lower limit of transmit power in dBm. For an 802.11a network, the system will only accept this configuration if the bsnGlobalDot11aDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. For an 802.11b network, the system will only accept this configuration if the bsnGlobalDot11bDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. The value of this attribute has to be less than equal to value of clrRrmParametersMaxTxPower. |
| I32 clrRrmParametersOptRoamDataRate | 1.3.6.1.4.1.9.9.615.1.1.1.1.23 | Integer32 | read-write | This object specifies the data rate threshold value for optimized roaming. A valid data rate in mbps must be entered. |
| T/F clrRrmParametersOptRoamEnable | 1.3.6.1.4.1.9.9.615.1.1.1.1.22 | TruthValue | read-write | This object specifies the state of optimized roaming feature on the controller. A value of 'true' indicates that the feature is enabled. A value of 'false' indicates that the feature is disabled |
| I32 clrRrmParametersOptRoamInterval | 1.3.6.1.4.1.9.9.615.1.1.1.1.24 | Integer32 | read-write | This object specifies the reporting interval value for Optimized Roaming. |
| INT clrRrmParametersPicoCellMode | 1.3.6.1.4.1.9.9.615.1.1.1.1.2 | INTEGER | read-write | This object specifies the 802.11 pico-cell mode. disable - pico-cell mode is disabled. picoCellv1 - legacy pico-cell mode is in use. picoCellv2 - in this mode the APs to use the tuple information from the clrRrmTupleTable. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| T/F clrRrmParametersRssiCheckEnable | 1.3.6.1.4.1.9.9.615.1.1.1.1.20 | TruthValue | read-write | This object specifies the state of RSSI low check on the controller. A value of 'true' indicates that the check is enabled. A value of 'false' indicates that the check is disabled. |
| I32 clrRrmParametersRssiThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.21 | Integer32 | read-write | This object specifies the RSSI threshold value for RSSI low check. |
| clrRrmParametersTable | 1.3.6.1.4.1.9.9.615.1.1.1 | not-accessible | This table represents the RRM parameters for a 802.11 interface type. Entries are automatically created on the controller for each 802.11 interface type. | |
| INT clrRrmParametersTpcVersion | 1.3.6.1.4.1.9.9.615.1.1.1.1.13 | INTEGER | read-write | This object specifies the TPC(Transmission Power Control) version. versionOne(1) - TPC would be in coverage optimal mode. versionTwo(2) - TPC would be in interference optimal mode. |
| CLA clrRrmParametersType | 1.3.6.1.4.1.9.9.615.1.1.1.1.1 | CLApIfType | not-accessible | This object uniquely represents the 802.11 interface type for this entry. |
| U32 clrRrmParametersVoicePktCountThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.4 | Unsigned32 | read-write | This object specifies the minimum threshold on the Voice packet count required to trigger the CHD algorithm on the controller. |
| U32 clrRrmParametersVoicePktPercentThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.5 | Unsigned32 | read-write | This object specifies the threshold on the percent of Voice packets dropped, that is required to trigger the CHD algorithm on the controller. |
| I32 clrRrmParametersVoiceRssiThreshold | 1.3.6.1.4.1.9.9.615.1.1.1.1.6 | Integer32 | read-write | This object specifies the RSSI threshold value for Voice packets, that is required to trigger the CHD algorithm on the controller. |
| clrRrmRemoveChannelEntry | 1.3.6.1.4.1.9.9.615.1.1.13.1 | not-accessible | Each entry in this table provides the removed channel information for an 802.11 interface from the default DCA channel list. | |
| U32 clrRrmRemoveChannelNum | 1.3.6.1.4.1.9.9.615.1.1.13.1.1 | Unsigned32 | not-accessible | The channel nubmer for this entry. This value represents the unique channel number removed from the default DCA channel list for the 802.11 interface for this regulatory domain. |
| ROW clrRrmRemoveChannelRowStatus | 1.3.6.1.4.1.9.9.615.1.1.13.1.3 | RowStatus | read-create | The status of this conceptual row. All writable objects in this row may be modified at any time. |
| clrRrmRemoveChannelTable | 1.3.6.1.4.1.9.9.615.1.1.13 | not-accessible | This table represents the removed channel information from default DCA channel list for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can remove a channel from this default DCA list and those channels will be put in this table. This table represents the removed channels information from the default DCA channel list. By default, there will not be any entries in this table. An entry can also be created or deleted from this table by using clrRrmChannelRowStatus. | |
| T/F clrRrmRemovedChannelDcaState | 1.3.6.1.4.1.9.9.615.1.1.13.1.2 | TruthValue | read-create | This object specifies whether this channel is part of the dynamic channel allocation (DCA) Remove List. A value of 'false' indicates that the DCA for this channel is disabled. |
| U32 clrRrmRfGroupingPriority | 1.3.6.1.4.1.9.9.615.1.1.8 | Unsigned32 | read-only | This object represents the priority assigned to controller with respect to RRM RF Grouping. When groups are formed, the priorities of the member controllers would be checked. Priority of the member controller should be less than or equal to priority of the leader controller. |
| U32 clrRrmRssiHistogramLength | 1.3.6.1.4.1.9.9.615.1.2.4 | Unsigned32 | accessible-for-notify | This object represents the number of values on the histogram. At present it is 31 entries. |
| I32 clrRrmRssiHistogramMaxIndex | 1.3.6.1.4.1.9.9.615.1.2.5 | Integer32 | accessible-for-notify | This object represents the maximum value on the histogram. |
| I32 clrRrmRssiHistogramMinIndex | 1.3.6.1.4.1.9.9.615.1.2.6 | Integer32 | accessible-for-notify | This object represents the minimum value on the histogram. |
| STR clrRrmRssiHistogramValues | 1.3.6.1.4.1.9.9.615.1.2.7 | SnmpAdminString | accessible-for-notify | This object returns a comma seperated string of histogram values. The number of values sent out is represented by the clrRrmRssiHistogramLength. |
| U32 clrRrmRssiHistogramValuesRev | 1.3.6.1.4.1.9.9.615.1.2.14 | Unsigned32 | accessible-for-notify | This object represents the histogram value. When notfication is being sent, there would as many instances of this object as the vlaue of 'clrRrmRssiHistogramLength'. |
| OCT clrRrmSysIdentifier | 1.3.6.1.4.1.9.9.615.1.2.13 | OCTET STRING | accessible-for-notify | This object represents the unique identifier for the controller. |
| IP clrRrmSysIpAddress | 1.3.6.1.4.1.9.9.615.1.2.21 | InetAddress | accessible-for-notify | This object represents the IPv4 and IPv6 address of the controller. |
| IPt clrRrmSysIpAddressType | 1.3.6.1.4.1.9.9.615.1.2.20 | InetAddressType | accessible-for-notify | This object represents the type of clrRrmSysIpAddress. |
| MAC clrRrmSysMacAddress | 1.3.6.1.4.1.9.9.615.1.2.12 | MacAddress | accessible-for-notify | This object represents the MAC Address of the controller. |
| MAC clrRrmSysMacAddressRev | 1.3.6.1.4.1.9.9.615.1.2.19 | MacAddress | accessible-for-notify | This object represents the MAC Address of the controller. |
| TIM clrRrmTimeStamp | 1.3.6.1.4.1.9.9.615.1.2.2 | TimeStamp | accessible-for-notify | This object indicates the time when coverage pre alarm was first reported to controller by an access point. After receiving this alert, controller will try to mitigate the coverage hole by increasing the transmit power of that access point. After doing above step for stipulated time, if coverage hole cannot be corrected by controller, a final notification would be generated from controller , informing the administrator about the existence of a coverage hole. |
| clrRrmTriRadioConfig | 1.3.6.1.4.1.9.9.615.1.1.17 | |||
| T/F clrRrmTriRadioMode | 1.3.6.1.4.1.9.9.615.1.1.17.1 | TruthValue | read-write | This object specifies the state of global tri-radio mode on the controller. A value of 'true' means global tri-radio mode is enabled. A value of 'false' indicates that the global tri-radio mode is disabled |
| CLR clrRrmTupleCcaSenseThreshold | 1.3.6.1.4.1.9.9.615.1.1.2.1.6 | ClrRrmTupleTuningRange | read-write | This object represents the current value for clear channel (CCA) sensitivity. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or may tune CCA sensitivity settings between the range of values configured by clrRrmTupleCcaSenseThresholdMin and clrRrmTupleCcaSenseThresholdMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleCcaSenseThresholdMax | 1.3.6.1.4.1.9.9.615.1.1.2.1.5 | ClrRrmTupleTuningRange | read-write | This object represents the maximum value configured for clear channel (CCA) sensitivity threshold. This value must be greater than the value configured for clrRrmTupleCcaSenseThresholdMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleCcaSenseThresholdMin | 1.3.6.1.4.1.9.9.615.1.1.2.1.4 | ClrRrmTupleTuningRange | read-write | This object represents the minimum value configured for clear channel (CCA) sensitivity threshold. This value must be less than the value configured for clrRrmTupleCcaSenseThresholdMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| clrRrmTupleEntry | 1.3.6.1.4.1.9.9.615.1.1.2.1 | not-accessible | Each entry represents the tuning parameters for an interface type. These entries are applicable only when object clrRrmParametersPicoCellMode is is set to 'picoCellv2'. Pico cell is no more supported so deprecating this attribute. It will be obsolete post 7.0 release. Object is deprecated since controller doesn't support Pico cell configuration anymore. | |
| CLR clrRrmTupleRxSenseThreshold | 1.3.6.1.4.1.9.9.615.1.1.2.1.3 | ClrRrmTupleTuningRange | read-write | This object represents the current value for receiver's sensitivity threshold. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or will tune receiver's sensitivity settings between the range of values configured by clrRrmTupleRxSenseThresholdMin and clrRrmTupleRxSenseThresholdMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleRxSenseThresholdMax | 1.3.6.1.4.1.9.9.615.1.1.2.1.2 | ClrRrmTupleTuningRange | read-write | This object represents the maximum value configured for receiver's sensitivity threshold. This value must be greater than the value configured for clrRrmTupleRxSenseThresholdMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleRxSenseThresholdMin | 1.3.6.1.4.1.9.9.615.1.1.2.1.1 | ClrRrmTupleTuningRange | read-write | This object represents the minimum value configured for receiver's sensitivity threshold. This value must be less than the value configured for clrRrmTupleRxSenseThresholdMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| T/F clrRrmTupleSetDefault | 1.3.6.1.4.1.9.9.615.1.1.2.1.10 | TruthValue | read-write | This object restores the other objects in this table to default value. Setting this value to 'true' wil restore defaults as indicated by the DEFVAL clause. This object can only be set to 'true' and all other values are rejected. This object will always return 'false' for get operations. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| clrRrmTupleTable | 1.3.6.1.4.1.9.9.615.1.1.2 | not-accessible | A list of tuple tuning parameters that are advertised to all APs registered under this 802.11 interface type. This information is pushed down to to 802.11 clients by the APs to operate under high density. Entries in this table are automatically created by the controller with default values. Object is deprecated since controller doesn't support Pico cell configuration anymore. | |
| CLR clrRrmTupleTransmitPowerLevel | 1.3.6.1.4.1.9.9.615.1.1.2.1.9 | ClrRrmTupleTuningRange | read-write | This object represents the current value for transmit power level. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or may tune the transmit power settings between the range of values configured by clrRrmTupleTransmitPowerLevelMin and clrRrmTupleTransmitPowerLevelMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleTransmitPowerLevelMax | 1.3.6.1.4.1.9.9.615.1.1.2.1.8 | ClrRrmTupleTuningRange | read-write | This object represents the maximum value configured for transmit power level. This value must be greater than the value for clrRrmTupleTransmitPowerLevelMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
| CLR clrRrmTupleTransmitPowerLevelMin | 1.3.6.1.4.1.9.9.615.1.1.2.1.7 | ClrRrmTupleTuningRange | read-write | This object represents the minimum value configured for transmit power level. This value must be less than the value configured for clrRrmTupleTransmitPowerLevelMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore. |
RFC description
Cisco vendor-private MIB for LWAPP (Lightweight Access Point Protocol) Radio Resource Management on wireless controllers and APs.
Start monitoring Cisco Wireless LAN Controllers (LWAPP-based) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.