| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoLwappExtMIB | 1.3.6.1.4.1.9.9.9998 | | | This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
tunnel from Light-weight LWAPP Access Points.
This MIB provides configuration and status information
about the Web Ext Server on the controller.
Particularly this mib covers the portal server for the wireless
controllers.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access control
( MAC ) and physical layer ( PHY ) interface and provides
access to the distribution services via the wireless medium
for associated clients.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the communication
between the Access Points and the Central Controller.
REFERENCE
[1] Part 11 Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications. |
| ciscoLwappExtMIBNotifs | 1.3.6.1.4.1.9.9.9998.0 | | | |
| NTF ciscoLwappApAssociatedNotify | 1.3.6.1.4.1.9.9.9998.0.1 | | | This notification is generated whenever an AP joins the
controller successfully. This notification contains
information about the last reboot reason, Data
Encryption status and the MAC address of the AP. |
| NTF ciscoLwappApDisassociated | 1.3.6.1.4.1.9.9.9998.0.2 | | | This notification is generated whenever an AP disassociate the
controller successfully. This notification contains
information about the last associate fail reason and MAC address
of the AP. |
| NTF ciscoLwappExtDot11ClientAuthenticationFailTrap | 1.3.6.1.4.1.9.9.9998.0.3 | | | This notification is generated whenever client Authentication
failure is detected. |
| NTF ciscoLwappExtDot11ClientAssocFailTrap | 1.3.6.1.4.1.9.9.9998.0.4 | | | This notification is generated whenever station associtation
failure is detacted. |
| ciscoLwappExtMIBObjects | 1.3.6.1.4.1.9.9.9998.1 | | | |
| ciscoLwappExtConfig | 1.3.6.1.4.1.9.9.9998.1.1 | | | |
| clExtSys | 1.3.6.1.4.1.9.9.9998.1.1.1 | | | |
| CLS clExtNMHeartBeatEnable | 1.3.6.1.4.1.9.9.9998.1.1.1.1 | CLSwitch | read-write | This object specifies whether heart beat trap to network
manager is enabled or disabled. If the value is on the
Network Manager Heart Beat feature is Enabled otherwise
Disabled. |
| INT clExtAgentResetSystem | 1.3.6.1.4.1.9.9.9998.1.1.1.2 | INTEGER | read-write | reset the switch |
| INT clExtAgentClearConfig | 1.3.6.1.4.1.9.9.9998.1.1.1.3 | INTEGER | read-write | Clear configuration to factory defaults |
| STR clExtSystemCurrentTime | 1.3.6.1.4.1.9.9.9998.1.1.1.4 | DisplayString | read-write | Use this attribute to change the System time on the Switch.
Specify the new time in this Format yyyy-mm-dd hh24:mi:ss.
For example, 2013-05-01 18:00:00. |
| clExtPortModeConfigTable | 1.3.6.1.4.1.9.9.9998.1.1.1.5 | | not-accessible | This table contains the entries for physical port related status |
| clExtPortModeConfigEntry | 1.3.6.1.4.1.9.9.9998.1.1.1.5.1 | | not-accessible | This entry contains the Switch's physical port phyical mode related attribues |
| INT clExtPortOperStatus | 1.3.6.1.4.1.9.9.9998.1.1.1.5.1.1 | INTEGER | read-only | The switch's Port Operation Status.This
is the current actual status. |
| I32 clExtSysMaxNewConnectionPerSecond | 1.3.6.1.4.1.9.9.9998.1.1.1.6 | Integer32 | read-only | This object specifies maximum number of new client count connect to
the controller per-second, it's a performance data and associated
with the platform |
| clExtIf | 1.3.6.1.4.1.9.9.9998.1.1.2 | | | |
| clExtIfTable | 1.3.6.1.4.1.9.9.9998.1.1.2.1 | | not-accessible | A list of interface entries. The number of entries
is given by the value of ifNumber. |
| clExtIfEntry | 1.3.6.1.4.1.9.9.9998.1.1.2.1.1 | | not-accessible | An entry containing management information applicable
to a particular interface. |
| G32 clExtIfSpeed | 1.3.6.1.4.1.9.9.9998.1.1.2.1.1.1 | Gauge32 | read-only | An estimate of the interface's current bandwidth in
million bits per second. For interfaces which do not vary in
bandwidth or for those where no accurate estimation
can be made, this object should contain the nominal
bandwidth. If the bandwidth of the interface is
greater than the maximum value reportable by this
object then this object should report its maximum
value (4,294,967,295 bps) and ifHighSpeed must be used to
report the interface's speed. For a sub-layer which
has no concept of bandwidth, this object should be
zero. |
| TIK clExtIfSinceLastChange | 1.3.6.1.4.1.9.9.9998.1.1.2.1.1.2 | TimeTicks | read-only | The value of time duration since the time the interface
entered its current operational state. If the current
time is prior to the last updating of the local network
management subsystem, then this object contains a zero value. |
| clExtAp | 1.3.6.1.4.1.9.9.9998.1.1.3 | | | |
| clExtApTable | 1.3.6.1.4.1.9.9.9998.1.1.3.1 | | not-accessible | This table represents the information about the
802.11 LWAPP Access Points that have joined the
controller.
LWAPP APs exchange configuration messages with the
controller and get the required configuration for
their 802.11 related operations, after they join the
controller. |
| clExtApEntry | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1 | | not-accessible | Each entry in this table provides information about
one 802.11 LWAPP Access Point that has joined the
controller.
Entries are removed when the APs lose their
association with the controller due to loss
of communication. |
| CLS clExtApRealTimeStatsModeEnabled | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.1 | CLSwitch | read-write | This object specifies whether currently stats mode is 'realtime'.
There are two stats-mode, realtime and normal, that specifies the
stats-timer range to be 10-180 sec and 2-5 sec each. Set to on
if current mode is realtime. |
| INT clExtApMonitorMode | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.2 | INTEGER | read-write | This object specifies the monitor mode of AP.
monitor : no client can connect.
normal : no monitor function at all.
semimonitor : AP can monitor it's working radio while clients connected.
The mapping between clExtApMonitorMode and CISCO existing function is as the belows:
clExtApMonitorMode Cisco Exist Value
LOCAL AP MODE: LOCAL + ROGUE DETECTION : disable
MONITOR AP MODE: MONITOR
SEMIMONITOR AP MODE: LOCAL + ROGUE DETECTION : enable |
| STR clExtApSysManufacture | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.3 | SnmpAdminString | read-only | This object specifies the AP manufacture. |
| STR clExtApSysSoftwareName | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.4 | SnmpAdminString | read-only | This object specifies the AP software name. |
| STR clExtApSysSoftwareVersion | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.5 | SnmpAdminString | read-only | This object specifies the AP software version. |
| STR clExtApSysSoftwareVendor | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.6 | SnmpAdminString | read-only | This object specifies the AP software vendor. |
| I32 clExtApQosMinBandwidth | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.7 | Integer32 | read-write | This object specifies the minimum bandwidth for QOS on the AP.
It is measured by Mbps. |
| U32 clExtApTotalPhyInterfaceCount | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.8 | Unsigned32 | read-only | This object specifies the total wired physical interface
count for the Access Points that have joined the controller. |
| STR clExtApName | 1.3.6.1.4.1.9.9.9998.1.1.3.1.1.9 | SnmpAdminString | read-write | This object represents the administrative name
assigned to the AP by the user. If an AP is not configured,
its factory default name will be ap: eg. ap:af:12:be. |
| clExtApDot11IfTable | 1.3.6.1.4.1.9.9.9998.1.1.3.2 | | not-accessible | This table represents the information about the
basic functional parameters corresponding to
the dot11 interfaces of the APs that have joined
the controller. |
| clExtApDot11IfEntry | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1 | | not-accessible | An entry in this table represents the 802.11
functional parameters of the dot11 interface of
an AP that has joined the controller.
Entries are added when the APs associate to this
controller and deleted when they lose their
association. |
| INT clExtAp11nChannelBandwidth | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.1 | INTEGER | read-write | This object indicates the channel bandwidth for
this AP. This applies to 802.11n networks only. |
| IAN clExtApDot11IfIANAType | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.2 | IANAifType | read-only | This object represents the type of this interface.
The value of the type is defined by IANA. |
| CLS clExtApIfPhyChannelAssignment | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.3 | CLSwitch | read-write | If this value is on, then bsnAPDot11CurrentChannel in
bsnAPIfDot11PhyDSSSTable is assigned by dynamic
algorithm and is read-only. |
| C64 clExtApDot11RadioStatsRxByteCountEx | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.4 | Counter64 | read-only | This object represents the total bytes of
packets received on the radio. |
| C64 clExtApDot11RadioStatsTxByteCount | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.5 | Counter64 | read-only | This object represents the total bytes of
packets transmitted on the radio. |
| INT clExtApDot11WirelessModeSupported | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.6 | INTEGER | read-only | This object represents wireless mode supported.
bit 0 - dot11a
bit 1 - dot11b
bit 2 - dot11g
bit 3 - dot11an
bit 4 - dot11gn
AP can support wireless multi-mode, the value can follow the example:
gn an g b a
--------------------
0 0 1 1 0
value:6, means b/g |
| INT clExtApDot11IfAdminStatus | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.7 | INTEGER | read-write | This object represents the AP's interface administrational
status. |
| INT clExtApDot11IfOperStatus | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.8 | INTEGER | read-only | This object represents the AP's wireless interface current operational
status. |
| I32 cLExtAPDot11IfRTSThreshold | 1.3.6.1.4.1.9.9.9998.1.1.3.2.1.9 | Integer32 | read-write | This object represents RTS threshold value. |
| clExtApDot11RadioStatsTable | 1.3.6.1.4.1.9.9.9998.1.1.3.3 | | not-accessible | This table represents the statistics information
about the radios of the APs that have joined the
controller. |
| clExtApDot11RadioStatsEntry | 1.3.6.1.4.1.9.9.9998.1.1.3.3.1 | | not-accessible | An entry in this table represents a statistics of
the radio of an AP that has joined the conttroller.
Entries are added when the APs associate to this
controller and deleted when they lose their
association. |
| C64 clExtApDot11RadioStatsRetryFrameCount | 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.1 | Counter64 | read-only | This object represents the total number of
downstream retry frames on the radio. |
| C64 clExtApDot11RadioStatsRetryPacketCount | 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.2 | Counter64 | read-only | This object represents the total number of
downstream retry packets on the radio. |
| C32 clExtApDot11RadioStatsRxErrorPacketCount | 1.3.6.1.4.1.9.9.9998.1.1.3.3.1.3 | Counter32 | read-only | This object represents the total number of
received error packets on the radio . |
| clExtApEthernetIfTable | 1.3.6.1.4.1.9.9.9998.1.1.3.4 | | not-accessible | This table represents the information about the
basic functional parameters corresponding to
the Ethernet interfaces of the APs that have joined
the controller. |
| clExtApEthernetIfEntry | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1 | | not-accessible | An entry in this table represents the functional
parameters of the Ethernet interface of an AP that
has joined the controller.
Entries are added when the APs associate to this
controller and deleted when they lose their
association. |
| INT clExtApEthernetIfOperStatus | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.1 | INTEGER | read-only | This object represents the operational state
of the physical Ethernet interface on the AP. |
| C32 clExtApEthernetIfRxBcastPkts | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.2 | Counter32 | read-only | This object represents total number of
broadcast packets received on the interface |
| C32 clExtApEthernetIfRxMcastPkts | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.3 | Counter32 | read-only | This object represents total number of
multicast packets received on the interface |
| C32 clExtApEthernetIfTxBcastPkts | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.4 | Counter32 | read-only | This object represents total number of
broadcast packets transmitted on the interface |
| C32 clExtApEthernetIfTxMcastPkts | 1.3.6.1.4.1.9.9.9998.1.1.3.4.1.5 | Counter32 | read-only | This object represents total number of
multicast packets transmitted on the interface |
| cLApOperationInfoTable | 1.3.6.1.4.1.9.9.9998.1.1.3.5 | | not-accessible | This table represents the operation information
for each AP. |
| cLApOperationInfoEntry | 1.3.6.1.4.1.9.9.9998.1.1.3.5.1 | | not-accessible | Each entry in this table provides operation
information for each AP. |
| MAC cLApOperationSysMacAddress | 1.3.6.1.4.1.9.9.9998.1.1.3.5.1.1 | MacAddress | not-accessible | This object specifies the AP mac address. |
| INT cLApOperationStatus | 1.3.6.1.4.1.9.9.9998.1.1.3.5.1.2 | INTEGER | read-only | This object represents operation status of each ap. |
| clExtWlan | 1.3.6.1.4.1.9.9.9998.1.1.4 | | | |
| clExtWlanConfigTable | 1.3.6.1.4.1.9.9.9998.1.1.4.1 | | not-accessible | This table represents the WLAN configuration sent by
the controller to the LWAPP APs for their operation.
LWAPP APs exchange configuration messages with the
controller and get the required configuration for
their 802.11 related operations. As part of these
messages, the WLAN configuration is pushed by the
controller to the LWAPP APs.
Rows are added or deleted by explicit
management actions initiated by the user from a
network management station through the
cLWlanRowStatus object. |
| clExtWlanConfigEntry | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1 | | not-accessible | Each entry in this table represents the WLAN
configuration sent by the controller to LWAPP APs
for use during their operations. entries can be
added/deleted by explicit management actions by
NMS or by user console |
| T/F clExtWlanAdminStatus | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.1 | TruthValue | read-create | Administrative Status of ESS(WLAN). By disabling an
ESS the corresponding SSID is no longer broadcasted
in AP beacons. |
| T/F clExtWlanBroadcastSsidEnable | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.2 | TruthValue | read-create | This attribute when enabled allows the switch to
broadcast this SSID and when disabled doesn't allow that. |
| INT clExtWlanLoadBalancingMode | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.3 | INTEGER | read-create | This object indicates the load balancing mode enabled
on the controller for this WLAN . A value of 'none'
indicates Load Balance is turned off for this Wlan.
A value of 'clientCount' indicates load balance is based
on AP client count scheme. And a value of 'uplinkUsage'
indicates load balance is based on AP uplink usage scheme. |
| T/F clExtWlanP2PBlocking | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.4 | TruthValue | read-create | This object represents per WLAN peer-to-peer
blocking behavior on controller. Peer-to-peer
blocking means traffic between two clients on
same VLAN will not be bridged.
false : Peer-to-peer blocking is disabled
and traffic is bridged locally
within the controller.
true : The packet will be discarded or
be forwarded on the upstream VLAN.
If it is forwarded on the upstream
VLAN, the device 'north' of the controller
can then make the decision about
decision about what to do with the
packet. |
| INT clExtWlanSecurityAuthType | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.5 | INTEGER | read-create | This object represents per WLAN type
of 802.11 Authentication.
authOpen : The WLAN uses open authentication method
authSharedKey : The WLAN uses shared authentication method
authCiscoLeap : The WLAN uses CISCO LEAP authentication
method |
| INT clExtWlanDot11Auth | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.6 | INTEGER | read-create | This object allows the user to configure
802.11 Authentication. |
| INT clExtWlanSecurity | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.7 | INTEGER | read-create | This object allows the user to configure
the security type in frame. |
| INT clExtWlanAuthenMode | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.8 | INTEGER | read-create | This object allows the user to configure
the authentication mode. |
| INT clExtWlanSecurityCiphers | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.9 | INTEGER | read-create | This object allows the user to configure
encryption mode. |
| INT clExtWepCipherKeyIndex | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.10 | INTEGER | read-write | This object represents the key index of WEP.
According to 802.11 standard 4 keys are supported.
So 802.11 Mobile Stations(Client) can have upto 4
keys. This index is for informing Mobile Station
which key it should use for Static WEP Authentication. |
| OCT clExtWepCipherKeyValue | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.11 | OCTET STRING | read-write | This object represents the key value of WEP.
For wep104 encryption either 26 bit hex key or
13 bit ascii key should be specified.
For wep40 encryption 10 bit hex key or 5 bit
ascii key should be specified. |
| INT clExtWepCipherKeyCharType | 1.3.6.1.4.1.9.9.9998.1.1.4.1.1.12 | INTEGER | read-write | This object represents the key type of WEP.
Length of key specified in Key depends on this attribute. |
| clExtDot11Client | 1.3.6.1.4.1.9.9.9998.1.1.5 | | | |
| clExtClientTable | 1.3.6.1.4.1.9.9.9998.1.1.5.1 | | not-accessible | This table represents the 802.11 wireless clients
that are associated with the APs that have joined
this controller.
An entry is created automatically by the controller
when the client gets associated to the AP. An existing
entry gets deleted when the association gets dropped.
Each client added to this table is uniquely identified
by the client's MAC address. |
| clExtClientEntry | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1 | | not-accessible | Each entry represents a conceptual row in this
table and provides the information about the
clients associated to the APs that have joined
the controller. An entry is identified the client's
MAC address. |
| INT clExtClientProtocol | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.1 | INTEGER | read-only | The 802.11 protocol type of the client.
'dot11a' - The client is using 802.11a standard
to connect to the access point (AP)
'dot11b' - The client is using 802.11b standard
to connect to the access point (AP)
'dot11g' - The client is using 802.11g standard
to connect to the access point (AP)
'dot11n5' - The client is using 802.11n standard
with 5 GHz frequency to connect to
the access point (AP).
'dot11n24' - The client is using 802.11n standard
with 2.4 GHz frequency to connect to
the access point (AP) |
| INT clExtClientPowerSaveMode | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.2 | INTEGER | read-only | This object indicates the power management mode of the client.
The possible two modes are:
active(0) - this client is not in power-save mode
and it is actively sending or receiving
data.
powersave(1) - this client is in power-save mode and it
wakes up once a while to check for
pending data. |
| TIK clExtClientUpTime | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.3 | TimeTicks | read-only | This object indicates the duration for which the client has
been associated with this device. |
| STR clExtClientAuthFailReason | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.5 | DisplayString | read-only | This object specifies the reason of the client authentication failure. |
| U32 clExtClientRxThroughput | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.6 | Unsigned32 | read-only | This object indicates the receiving throughput which expressing a instantaneous throughput of the bytes
received by the client over last time slot. |
| U32 clExtClientTxThroughput | 1.3.6.1.4.1.9.9.9998.1.1.5.1.1.7 | Unsigned32 | read-only | This object indicates the transmitting throughput which expressing a instantaneous throughput of the bytes
transmitted by the client over last time slot. |
| clExtDot11 | 1.3.6.1.4.1.9.9.9998.1.1.6 | | | |
| clExtHtMacOperationsTable | 1.3.6.1.4.1.9.9.9998.1.1.6.1 | | not-accessible | This table represents the operational parameters
at the MAC layer for the 802.11n networks managed
through the controller. An agent adds an entry to
this table for every 802.11n band on startup. |
| clExtHtMacOperationsEntry | 1.3.6.1.4.1.9.9.9998.1.1.6.1.1 | | not-accessible | Each entry represents the operational parameters
at the MAC layer for 802.11n networks. |
| CLS clExtHtDot11nAmpduEnable | 1.3.6.1.4.1.9.9.9998.1.1.6.1.1.1 | CLSwitch | read-write | This object is used to indicate the support for 802.11n
A-MPDU on this band. A value of 'on' indicates that
A-MPDU is enabled for this band. A value of 'off'
indicates that A-MPDU is disabled for this band. |
| CLS clExtHtDot11nGuardIntervalEnable | 1.3.6.1.4.1.9.9.9998.1.1.6.1.1.2 | CLSwitch | read-write | This object is used to indicate the support for 802.11n
guard interval on this band. A value of 'on' indicates
that guard interval is enabled for this band. A value of
'off' indicates that guard interval is disabled for
this band. |
| clExtRF | 1.3.6.1.4.1.9.9.9998.1.1.7 | | | |
| clExtRFProfileTable | 1.3.6.1.4.1.9.9.9998.1.1.7.1 | | not-accessible | This table lists the configuration for each
RF profile. |
| clExtRFProfileEntry | 1.3.6.1.4.1.9.9.9998.1.1.7.1.1 | | not-accessible | An entry containing the configuration attributes
that affect the operation of 802.11 RF domain.
Entries can be added/deleted by explicit management
action from NMS/EMS or through user console. |
| U32 clExtRFProfileWirelessMode | 1.3.6.1.4.1.9.9.9998.1.1.7.1.1.1 | Unsigned32 | read-write | This object represents wireless mode configuration.
bit 0 - dot11a
bit 1 - dot11b
bit 2 - dot11g
bit 3 - dot11an
bit 4 - dot11gn
AP can support wireless multi-mode, the value can follow the example:
gn an g b a
--------------------
0 0 1 1 0
value:6, means b/g |
| clExtSecurity | 1.3.6.1.4.1.9.9.9998.1.1.8 | | | |
| clExtAbnormalOfflineClientOnSecurityTypeTable | 1.3.6.1.4.1.9.9.9998.1.1.8.1 | | not-accessible | This table lists the abnormal offline clients for the required
security type. |
| clExtAbnormalOfflineClientOnSecurityTypeEntry | 1.3.6.1.4.1.9.9.9998.1.1.8.1.1 | | not-accessible | Each entry in this table represents the abnormal
offline counter based on security type. |
| INT clExtSecurityType | 1.3.6.1.4.1.9.9.9998.1.1.8.1.1.1 | INTEGER | not-accessible | This object represents the client security type.
open : The client uses open authentication method
wepPsk : The client uses WEP/PSK authentication method
peapSim : The client uses PEAP/SIM authentication method
webAuth : The client uses WebAuth authentication method |
| C32 clExtAbnormalOfflineClientCount | 1.3.6.1.4.1.9.9.9998.1.1.8.1.1.2 | Counter32 | read-only | This object represents the current abnormal offline clients
based on security type on the controller. |
| ciscoLwappExtStats | 1.3.6.1.4.1.9.9.9998.1.2 | | | |
| ciscoLwappExtMIBConform | 1.3.6.1.4.1.9.9.9998.2 | | | |
| ciscoLwappExtMIBNotifObjects | 1.3.6.1.4.1.9.9.9998.3 | | | |
| CLE cLExtApDisassocReason | 1.3.6.1.4.1.9.9.9998.3.1 | CLExtApDisassocReason | accessible-for-notify | This object specifies the failure reasons when
the AP disassociate with a controller. |
| STR cLExtDot11ClientAssocFailReason | 1.3.6.1.4.1.9.9.9998.3.2 | DisplayString | accessible-for-notify | This object specifies the reason of the station association failure. |
| MAC cLExtApDetectedMacAddress | 1.3.6.1.4.1.9.9.9998.3.3 | MacAddress | accessible-for-notify | This object represents the radio MAC address
common to the dot11 interfaces of the detected AP. |
| CLD cLExtApDetectedChannel | 1.3.6.1.4.1.9.9.9998.3.4 | CLDot11Channel | accessible-for-notify | This object represents the detected channel number. |
| STR cLExtApDectedSsid | 1.3.6.1.4.1.9.9.9998.3.5 | SnmpAdminString | accessible-for-notify | This object represents the SSID used by the
rogue AP to intrude the network. |
