CISCO-LWAPP-RF-MIB

All MIBs › CISCO-LWAPP-RF-MIB

Organization: Cisco Systems Inc.

Last Updated: 2020-10-07

Category: Cisco Devices, Wireless and WLAN

Description: Manages radio frequency parameters including channel, power, and interference for Cisco LWAPP access points.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-LWAPP-RF-MIB?

This is a vendor-specific MIB from Cisco for managing Radio Frequency (RF) parameters on Wireless LAN Controllers (Central Controllers) that terminate the Lightweight Access Point Protocol (LWAPP) tunnel from Cisco lightweight access points. It exposes RF profile definitions per AP group and radio band (802.11a/802.11bg), including transmit power minimum/maximum and power-threshold settings used for RF power management across a wireless deployment. Its monitoring relevance is configuration/operational status of the wireless RF layer: administrators check cLRFProfileTransmitPowerMin/Max and threshold values against a group's assigned cLAPGroups802dot11aRFProfileName/cLAPGroups802dot11bgRFProfileName to confirm access points are operating within intended power bounds, which affects coverage, interference, and roaming behavior. It is explicitly built on the LWAPP tunnel architecture connecting lightweight APs to Cisco wireless controllers, so it depends on that underlying protocol relationship. It is deployed in enterprise Cisco Unified Wireless Network installations using lightweight APs managed by a central WLC. Network engineers evaluating or troubleshooting this functionality can download the CISCO-LWAPP-RF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-RF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco Wireless LAN Controller (Central Controller) with LWAPP lightweight access points

Monitoring Examples

An admin checks cLAPGroupsRFProfileTable/cLAPGroupsRFProfileEntry to see which cLRFProfileName is assigned to an AP group's 802.11a and 802.11bg radios, then inspects cLRFProfileTable/cLRFProfileEntry for that profile's cLRFProfileTransmitPowerMin and cLRFProfileTransmitPowerMax to confirm APs aren't transmitting outside the intended power range. cLRFProfileTransmitPowerThresholdV1/V2 values are compared against observed AP power levels to catch an AP whose automatic power control has drifted, a likely cause of dead zones or excessive channel overlap. cLRFProfileDescr provides a human-readable label for each profile to aid in auditing which coverage policy is applied where.

What Can Be Monitored

RF profile assignment per AP group/radio band
transmit power minimum/maximum settings
transmit power threshold configuration
RF profile description/name

Imported Objects

From CISCO-LWAPP-TC-MIB

CLApIfType

From CISCO-LWAPP-WLAN-MIB

cLAPGroupName

OBJECT-TYPE

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoLwappRFConfig	1.3.6.1.4.1.9.9.778.1.1
ciscoLwappRFConfigGroup	1.3.6.1.4.1.9.9.778.2.2.1			This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.This config group ciscoLwappRFConfigGroup is deprecated and replaced by ciscoLwappRFConfigGroupVer1
ciscoLwappRFConfigGroup1	1.3.6.1.4.1.9.9.778.2.2.3			This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
ciscoLwappRFConfigGroup3	1.3.6.1.4.1.9.9.778.2.2.6			This object specifies the configuration DCA for RF Profiles.
ciscoLwappRFConfigGroup4	1.3.6.1.4.1.9.9.778.2.2.7			This object specifies the receiver start of packet threshold for RF Profiles.
ciscoLwappRFConfigGroup5	1.3.6.1.4.1.9.9.778.2.2.11			This object specifies the receiver start of packet threshold for RF Profiles.
ciscoLwappRFConfigGroup6	1.3.6.1.4.1.9.9.778.2.2.12			This collection of object specifies the configuration of AirTime Fairness parameters.
ciscoLwappRFConfigGroup7	1.3.6.1.4.1.9.9.778.2.2.13			This collection of object specifies the removed channel and add channel list information from default DCA channel list for a RF profile
ciscoLwappRFConfigGroup8	1.3.6.1.4.1.9.9.778.2.2.14			This collection of objects specifies the 802.11ax OBSS PD spatial reuse configurations for RF Profiles.
ciscoLwappRFConfigGroupExtension1	1.3.6.1.4.1.9.9.778.2.2.10			This object specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
ciscoLwappRFConfigGroupVer1	1.3.6.1.4.1.9.9.778.2.2.2			This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
ciscoLwappRFGlobalConfigGroup	1.3.6.1.4.1.9.9.778.2.2.4			This is the RF global config parameter.
ciscoLwappRFGlobalObjects	1.3.6.1.4.1.9.9.778.1.2
ciscoLwappRFGroupChannelConfig	1.3.6.1.4.1.9.9.778.2.2.9			This object specifies the add and remove channels for RF Profiles.
ciscoLwappRFGroupDCAChannelConfig	1.3.6.1.4.1.9.9.778.2.2.8			This object specifies the add and remove channels for RF Profiles.
ciscoLwappRFGroupTrapThresholdConfig	1.3.6.1.4.1.9.9.778.2.2.5			This object specifies the configuration of Trap threshold to be configured on the interface of an LWAPP AP.
ciscoLwappRFMIB	1.3.6.1.4.1.9.9.778			This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB helps to manage the Radio Frequency (RF) parameters on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected to. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the controllers. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Radio Frequency ( RF ) Radio frequency (RF) is a rate of oscillation in the range of about 3 kHz to 300 GHz, which corresponds to the frequency of radio waves, and the alternating currents which carry radio signals. Received Signal Strength Indicator ( RSSI ) A measure of the strength of the signal as observed by the entity that received it, expressed in 'dbm'. Coverage Hole Detection ( CHD ) If clients on an Access Point are detected at low RSSI levels, it is considered a coverage hole by the Access Points. This indicates the existence of an area where clients are continually getting poor signal coverage, without having a viable location to roam to. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol [3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s, 2.4 GHz RF and IR standard.
ciscoLwappRFMIBCompliance	1.3.6.1.4.1.9.9.778.2.1.1			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. This compliance is deprecated and replaced by ciscoLwappRFMIBComplianceVer1 .
ciscoLwappRFMIBComplianceRev3	1.3.6.1.4.1.9.9.778.2.1.4			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
ciscoLwappRFMIBComplianceRev4	1.3.6.1.4.1.9.9.778.2.1.5			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
ciscoLwappRFMIBComplianceRev5	1.3.6.1.4.1.9.9.778.2.1.6			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
ciscoLwappRFMIBCompliances	1.3.6.1.4.1.9.9.778.2.1
ciscoLwappRFMIBComplianceVer1	1.3.6.1.4.1.9.9.778.2.1.2			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
ciscoLwappRFMIBComplianceVer2	1.3.6.1.4.1.9.9.778.2.1.3			The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. Added ciscoLwappRFConfigGroup2 to add object to raise trap when client count exceeds threshold and ciscoLwappRFConfigGroup3 to address DCA settings
ciscoLwappRFMIBConform	1.3.6.1.4.1.9.9.778.2
ciscoLwappRFMIBGroups	1.3.6.1.4.1.9.9.778.2.2
ciscoLwappRFMIBNotifs	1.3.6.1.4.1.9.9.778.0
ciscoLwappRFMIBObjects	1.3.6.1.4.1.9.9.778.1
STR cLAPGroups802dot11aRFProfileName	1.3.6.1.4.1.9.9.778.1.1.1.1.2	SnmpAdminString	read-write	This object specifies the RF profile name assigned to this site on the 802.11a radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set.
STR cLAPGroups802dot11bgRFProfileName	1.3.6.1.4.1.9.9.778.1.1.1.1.1	SnmpAdminString	read-write	This object specifies the RF profile name assigned to this site on the 802.11bg radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set.
cLAPGroupsRFProfileEntry	1.3.6.1.4.1.9.9.778.1.1.1.1		not-accessible	An entry containing the configuration attributes that affect the operation of the APs within a group. Entries can be added/deleted by explicit management action from NMS/EMS through the 'bsnAPGroupsVlanRowStatus' object in bsnAPGroupsVlanTable as defined by the AIRESPACE-WIRELESS-MIB.
cLAPGroupsRFProfileTable	1.3.6.1.4.1.9.9.778.1.1.1		not-accessible	This table lists the mapping between an RF profile and an AP group.
I32 cLRFProfile11axNonSrgObssPdMax	1.3.6.1.4.1.9.9.778.1.1.2.1.57	Integer32	read-write	This object specifies the non-SRG OBSS PD max threshold in dBm for the RF profile.
T/F cLRFProfile11axObssPdEnable	1.3.6.1.4.1.9.9.778.1.1.2.1.56	TruthValue	read-write	This object specifies whether 802.11ax OBSS PD spatial reuse is enabled for the RF profile.
T/F cLRFProfile11nOnly	1.3.6.1.4.1.9.9.778.1.1.2.1.36	TruthValue	read-create	This object specifies if 11n-client-only mode is enabled. A value of 'true' indicates 11n-client-only mode enabled. A value of 'false' indicates 11n-client-only mode disabled.
cLRFProfileAddChannelEntry	1.3.6.1.4.1.9.9.778.1.1.6.1		not-accessible	Each entry in this table provides the added channel information to the default DCA channel list in this RF profile.
STR cLRFProfileAddChannelName	1.3.6.1.4.1.9.9.778.1.1.6.1.1	SnmpAdminString	not-accessible	This object uniquely identifies a RF Profile.
U32 cLRFProfileAddChannelNum	1.3.6.1.4.1.9.9.778.1.1.6.1.2	Unsigned32	not-accessible	The channel nubmer for this entry. This value represents the unique channel number added to the default DCA list in this RF profile.
ROW cLRFProfileAddChannelRowStatus	1.3.6.1.4.1.9.9.778.1.1.6.1.4	RowStatus	read-create	The status of this conceptual row. All writable objects in this row may be modified at any time.
cLRFProfileAddChannelTable	1.3.6.1.4.1.9.9.778.1.1.6		not-accessible	This table represents the added channel information to the default DCA channel list in this RF profile. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can add a channel to this default list and those channels will be put in this table. This table represents the added channels information to the default DCA channel list. By default, there will not be any entries in this table. An entry can be created or deleted from this table using cLRFProfileAddChannelRowStatus.
T/F cLRFProfileAddedChannelDcaState	1.3.6.1.4.1.9.9.778.1.1.6.1.3	TruthValue	read-create	This object specifies whether this channel is part of the dynamic channel allocation (DCA) Add List. A value of 'true' indicates that the DCA for this channel is enabled.
U32 cLRFProfileAirTimeAllocation	1.3.6.1.4.1.9.9.778.1.1.2.1.54	Unsigned32	read-write	This object specifies the percentage for airtime allocation for the client access node.
INT cLRFProfileAirTimeFairnessMode	1.3.6.1.4.1.9.9.778.1.1.2.1.51	INTEGER	read-write	This object specifies the mode of fairness for ATF supported APs, joined to the controller. disable(1) - This indicates that fairness mode is disabled. SSID Mode(2) - This indicates that fairness mode is SSID mode. Monitor Mode(3) - This indicates that fairness mode is monitor mode.
INT cLRFProfileAirTimeFairnessOptimization	1.3.6.1.4.1.9.9.778.1.1.2.1.52	INTEGER	read-write	This object specifies the optimization for ATF supported APs, joined to the controller to be configured.
I32 cLRFProfileBandSelectClientMidRSSI	1.3.6.1.4.1.9.9.778.1.1.2.1.47	Integer32	read-create	This object specifies medium mobile station RSSI threshold. Mobile station between this value and cldBandSelectClientRssi will be recorded in suppressed table but will not be denied. The mobile station having RSSI stronger than this value will be recorded and denied.
I32 cLRFProfileBandSelectClientRSSI	1.3.6.1.4.1.9.9.778.1.1.2.1.28	Integer32	read-create	This object specifies minimum mobile station RSSI threshold. Mobile stations having RSSI below this value will not be recorded in the suppressed table. This configuration filters out far away mobile stations with weaker signal strength. This will limit the number of mobile stations on the table to a reasonable amount.
U32 cLRFProfileBandSelectCycleCount	1.3.6.1.4.1.9.9.778.1.1.2.1.24	Unsigned32	read-create	This object specifies number of times a client probe (2.4 G-Hz) is suppressed before the AP starts responding to the probes.
U32 cLRFProfileBandSelectCycleThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.25	Unsigned32	read-create	This object specifies time threshold for a new scanning mobile station period. Mobile station cycle counter will increment only if mobile station scans same channel any time after threshold is passed.
U32 cLRFProfileBandSelectExpireDualBand	1.3.6.1.4.1.9.9.778.1.1.2.1.27	Unsigned32	read-create	This object specifies the timeout duration until which an AP should not respond to 2.4ghz probe requests from a dual-band client. Once this band select duration expires the client will be marked as a non-dual band client and AP will start responding to the 2.4 Ghz probes.
U32 cLRFProfileBandSelectExpireSuppression	1.3.6.1.4.1.9.9.778.1.1.2.1.26	Unsigned32	read-create	This object specifies the duration at which an AP waits to conduct another probe suppression.
T/F cLRFProfileBandSelectProbeResponse	1.3.6.1.4.1.9.9.778.1.1.2.1.23	TruthValue	read-create	This object specifies the AP's probe response with clients to verify whether client can associate on both 2.4 GHz and 5Ghz spectrum. When set to true, AP suppresses probe response to new clients for all SSIDs that are not being Band Select disabled.
T/F cLRFProfileBridgeClientAccess	1.3.6.1.4.1.9.9.778.1.1.2.1.53	TruthValue	read-write	This object specifies whether airtime allocation is enabled for the client access node.
INT cLRFProfileChanAddRemove	1.3.6.1.4.1.9.9.778.1.1.4.1.2	INTEGER	read-create	This object specifies a channel is to be added or removed from DCA list of the RFProfile. add - Add the channel to global DCA channel list. remove - Removed the channel from global DCA channel list.
cLRFProfileChannelListEntry	1.3.6.1.4.1.9.9.778.1.1.4.1		not-accessible	An entry containing Channel List information applicable to a particular profile.
cLRFProfileChannelListTable	1.3.6.1.4.1.9.9.778.1.1.4		not-accessible	This object specifies the list of channels that is available for DCA of a RF profile.
U32 cLRFProfileChanNumber	1.3.6.1.4.1.9.9.778.1.1.4.1.1	Unsigned32	not-accessible	This object uniquely identifies the channel for a particular profile.
ROW cLRFProfileChanRowStatus	1.3.6.1.4.1.9.9.778.1.1.4.1.3	RowStatus	read-create	This is the status column for this row and used to create and delete specific instances of rows in this table.
U32 cLRFProfileCHDClientExceptionLevel	1.3.6.1.4.1.9.9.778.1.1.2.1.33	Unsigned32	read-create	This object specifies the minimum number of clients required to trigger coverage hole.
U32 cLRFProfileCHDCoverageExceptionLevel	1.3.6.1.4.1.9.9.778.1.1.2.1.34	Unsigned32	read-create	This object specifies the minimum percentage of clients in the coverage hole region of the AP, required to trigger a coverage hole exception
I32 cLRFProfileCHDDataRSSIThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.31	Integer32	read-create	This object specifies the RSSI value for non-voice clients i.e., clients sending only data traffic to trigger coverage event.
I32 cLRFProfileCHDVoiceRSSIThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.32	Integer32	read-create	This object specifies the RSSI value for voice clients to trigger coverage event.
INT cLRFProfileClientNetworkPreference	1.3.6.1.4.1.9.9.778.1.1.2.1.48	INTEGER	read-create	This object represents the client network preference. default(0) - RRM Algorithm has no preference on the clients. connectivity(1) - RRM Algorithm has a preference on connectiviry of the clients. throughput(2) - RRM Algorithm has a preference on high thoughput of the clients.
CIS cLRFProfileDataRate11Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.10	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate12Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.13	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate18Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.14	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate1Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.7	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate24Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.15	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate2Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.8	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate36Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.16	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate48Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.17	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate54Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.18	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate5AndHalfMbps	1.3.6.1.4.1.9.9.778.1.1.2.1.9	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate6Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.11	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
CIS cLRFProfileDataRate9Mbps	1.3.6.1.4.1.9.9.778.1.1.2.1.12	CiscoLwappRFApDataRates	read-create	This object specifies the configuration for this data rate.
STR cLRFProfileDCAChannelList	1.3.6.1.4.1.9.9.778.1.1.2.1.43	SnmpAdminString	read-create	This object specifies the 802.11 channels available to the RF Profile. A comma separated list of integers.
INT cLRFProfileDCAChannelWidth	1.3.6.1.4.1.9.9.778.1.1.2.1.42	INTEGER	read-create	This object specifies how the system performs DCA channel width selection for the RFProfile twenty - 20MHz channel width supported by this radio. forty - 40MHz channel width supported by this radio. eighty - 80MHz channel width supported by this radio. onesixty - 160MHz channel width supported by this radio. best - Dynamic channel width(160MHz, 80MHz, 40MHz or 20MHz) supported by this radio.
T/F cLRFProfileDCAForeignContribution	1.3.6.1.4.1.9.9.778.1.1.2.1.41	TruthValue	read-create	This object specifies whether foreign interference is taken into account for the DCA metrics. A value of 'true' indicates that foreign interference is is considered when DCA metrics is derived. A value of 'false' indicates foreign interference is not taken into account when deriving the DCA metrics.
STR cLRFProfileDescr	1.3.6.1.4.1.9.9.778.1.1.2.1.2	SnmpAdminString	read-create	This object specifies a human-readable description of the profile.
cLRFProfileEntry	1.3.6.1.4.1.9.9.778.1.1.2.1		not-accessible	An entry containing the configuration attributes that affect the operation of 802.11 RF domain. Entries can be added/deleted by explicit management action from NMS/EMS or through user console.
U32 cLRFProfileHDClientTrapThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.37	Unsigned32	read-create	This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the count of clients on the AP radio reaches this limit. A value of zero indicates that the trap is disabled.
U32 cLRFProfileHighDensityMaxRadioClients	1.3.6.1.4.1.9.9.778.1.1.2.1.22	Unsigned32	read-create	This object specifies the maximum number of clients per AP radio in high density environment.
T/F cLRFProfileHSRMode	1.3.6.1.4.1.9.9.778.1.1.2.1.45	TruthValue	read-create	This object specifies whether HSR mode for RF profile is enabled or not. A value of 'true' indicates that HSR is enabled. A value of 'false' indicates that HSR is disabled.
U32 cLRFProfileHSRNeighborTimeoutFactor	1.3.6.1.4.1.9.9.778.1.1.2.1.46	Unsigned32	read-create	This object specifies the timeout interval of neighbors that will be configured for RF profile. Neighbor timeout factor will be five times the neighbor interval
U32 cLRFProfileInterferenceThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.38	Unsigned32	read-create	This object specifies interference threshold in % traps are generated when interference exceeds this value .
U32 cLRFProfileLoadBalancingMaxDenialCount	1.3.6.1.4.1.9.9.778.1.1.2.1.30	Unsigned32	read-create	This object specifies maximum number of association rejections sent by AP to a mobile station for a given sequence of association. When a mobile station tries to associate on wireless network, it sends association request to AP. If AP is overloaded and load balancing is enable on controller, AP will send a denial to association request. If there are no other AP in the vicinity of mobile station, it will try to associate same AP again. So to restrict the number of denial sent from AP, cldLoadBalancingMaxDenialCount is defined. After maximum denial count is reached mobile station will be able to associate.
U32 cLRFProfileLoadBalancingWindowSize	1.3.6.1.4.1.9.9.778.1.1.2.1.29	Unsigned32	read-create	This object specifies the minimum number of clients to be associated on an AP in order to trigger load balancing.
cLRFProfileMcsDataRateEntry	1.3.6.1.4.1.9.9.778.1.1.3.1		not-accessible	An entry containing MCS date rate information applicable to a particular profile. Entry is added to the table when the data rate is set to 'supported' or 'mandatory'.
cLRFProfileMcsDataRateTable	1.3.6.1.4.1.9.9.778.1.1.3		not-accessible	This object specifies the 11n MCS rates supported by the RF profile, indexed by the MCS rate, ranging from 1 to 32, corresponding to rate MCS-0, MCS-1, ... MCS-31.
STR cLRFProfileMcsName	1.3.6.1.4.1.9.9.778.1.1.3.1.1	SnmpAdminString	not-accessible	This object uniquely identifies a RF Profile.
U32 cLRFProfileMcsRate	1.3.6.1.4.1.9.9.778.1.1.3.1.2	Unsigned32	not-accessible	This object uniquely identifies the MCS data rate for a particular profile.
T/F cLRFProfileMcsRateSupport	1.3.6.1.4.1.9.9.778.1.1.3.1.3	TruthValue	read-write	This object is used to enable or disable the data rate. A value of 'true' indicates MCS support is enabled. A value of 'false' indicates MCS support is disabled.
U32 cLRFProfileMulticastDataRate	1.3.6.1.4.1.9.9.778.1.1.2.1.35	Unsigned32	read-create	This object specifies the minimum data rate at which multicast clients can associate to AP. A value 0 indicates that AP will automatically adjust data rates.
STR cLRFProfileName	1.3.6.1.4.1.9.9.778.1.1.2.1.1	SnmpAdminString	not-accessible	This object uniquely identifies a RF Profile.
I32 cLRFProfileNoiseThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.39	Integer32	read-create	This object specifies the threshold number of noise threshold between -127 and 0 dBm.
T/F cLRFProfileOutOfBoxAPConfig	1.3.6.1.4.1.9.9.778.1.2.1	TruthValue	read-write	This object specifies the out of box AP config feature. Enabling this feature will allow any AP that does not have group name configured upon join to controller then it will be considered as out of box AP and it will be moved to a special AP Group. Disabling this feature will only stop further subscription of new AP's to Out of Box AP group. A value of 'true' indicates that out of box AP feature is enabled and APs will be moved to newly created AP group out-of-box and shut of their radios. A value of 'false' indicates that out of box AP feature is disabled.
T/F cLRFProfileOutOfBoxAPPersistenceConfig	1.3.6.1.4.1.9.9.778.1.2.2	TruthValue	read-write	This object specifies the out of box AP group to be persistent or not. A value of 'true' indicates out-of-box persistence need to be enabled. A value of 'false' indicates out-of-box persistence need to be disabled.
CLA cLRFProfileRadioType	1.3.6.1.4.1.9.9.778.1.1.2.1.19	CLApIfType	read-create	This object is used to configure the radio type for this profile.
cLRFProfileRemoveChannelEntry	1.3.6.1.4.1.9.9.778.1.1.5.1		not-accessible	Each entry in this table provides the removed channel information from the default DCA channel list for this RF profile
STR cLRFProfileRemoveChannelName	1.3.6.1.4.1.9.9.778.1.1.5.1.1	SnmpAdminString	not-accessible	This object uniquely identifies a RF Profile.
U32 cLRFProfileRemoveChannelNum	1.3.6.1.4.1.9.9.778.1.1.5.1.2	Unsigned32	not-accessible	The channel nubmer for this entry. This value represents the unique channel number removed from default DCA channel list for this RF profile.
ROW cLRFProfileRemoveChannelRowStatus	1.3.6.1.4.1.9.9.778.1.1.5.1.4	RowStatus	read-create	The status of this conceptual row. All writable objects in this row may be modified at any time.
cLRFProfileRemoveChannelTable	1.3.6.1.4.1.9.9.778.1.1.5		not-accessible	This table represents the removed channel information from default DCA channel list for an AP's 802.11 interface using the RF profile. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can remove a channel from this default list and those channels will be put in this table. This table represents the removed DCA channels information. By default, there will not be any entries in this table. An entry can be created or deleted from this table using cLRFProfileRemoveChannelRowStatus.
T/F cLRFProfileRemovedChannelDcaState	1.3.6.1.4.1.9.9.778.1.1.5.1.3	TruthValue	read-create	This object specifies whether this channel is part of the dynamic channel allocation (DCA) Remove List. A value of 'false' indicates that the DCA for this channel is disabled.
ROW cLRFProfileRowStatus	1.3.6.1.4.1.9.9.778.1.1.2.1.21	RowStatus	read-create	This is the status column for this row and used to create and delete specific instances of rows in this table.
INT cLRFProfileRxSopThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.44	INTEGER	read-create	This object specifies the receiver start of packet threshold for the rf profile. auto - Reverts radio receiver SOP to auto. high - Sets radio receiver SOP to high. low - Sets radio receiver SOP to low. medium - Sets radio receiver SOP to medium. custom - Sets radio receiver SOP to Custom value.
I32 cLRFProfileRxSopThresholdCustom	1.3.6.1.4.1.9.9.778.1.1.2.1.55	Integer32	read-write	This object specifies the percentage for the receiver start of packet custom threshold for the client access node.
T/F cLRFProfileShutdown	1.3.6.1.4.1.9.9.778.1.1.2.1.50	TruthValue	read-write	This object specifies if rf profile is disabled.
STO cLRFProfileStorageType	1.3.6.1.4.1.9.9.778.1.1.2.1.20	StorageType	read-create	This object represents the storage type for this conceptual row.
cLRFProfileTable	1.3.6.1.4.1.9.9.778.1.1.2		not-accessible	This table lists the configuration for each RF profile.
I32 cLRFProfileTransmitPowerMax	1.3.6.1.4.1.9.9.778.1.1.2.1.4	Integer32	read-create	This object specifies the uppoer bound of transmit power value supported by an AP.
I32 cLRFProfileTransmitPowerMin	1.3.6.1.4.1.9.9.778.1.1.2.1.3	Integer32	read-create	This object specifies the lower bound of transmit power value supported by an AP.
I32 cLRFProfileTransmitPowerThresholdV1	1.3.6.1.4.1.9.9.778.1.1.2.1.5	Integer32	read-create	This object specifies the transmit power control version 1 threshold for the radio resource management algorithm.
I32 cLRFProfileTransmitPowerThresholdV2	1.3.6.1.4.1.9.9.778.1.1.2.1.6	Integer32	read-create	This object specifies the transmit power control version 2 threshold for the radio resource management algorithm.
STR cLRFProfileUnusedChannelList	1.3.6.1.4.1.9.9.778.1.1.2.1.49	SnmpAdminString	read-only	This object specifies the 802.11 channels present in ths un-used channel list of RF Profile. A comma separated list of integers.
U32 cLRFProfileUtilizationThreshold	1.3.6.1.4.1.9.9.778.1.1.2.1.40	Unsigned32	read-create	This object specifies the threshold of bandwidth (%) being utilized by an access-point. Traps are sent when this value is exceeded

RFC description

Manages radio frequency parameters on Cisco wireless controllers for lightweight access points.

Start monitoring Cisco Wireless LAN Controllers (LWAPP-based) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-LWAPP-RF-MIB

What Is CISCO-LWAPP-RF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description