All MIBs › CISCO-IETF-VDSL-LINE-MIB
Organization: Cisco Systems
Last Updated: 2002-04-18
Category: Cisco Devices, DSL and Broadband
Description: Provides the IETF VDSL line MIB implementation, covering VDSL interface configuration and statistics on Cisco devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-IETF-VDSL-LINE-MIB?
CISCO-IETF-VDSL-LINE-MIB is Cisco's implementation of the IETF standard MIB for managing VDSL (Very-high-bit-rate Digital Subscriber Line) modem pairs on Cisco routers and access devices equipped with VDSL line cards. It exposes configuration and status data for each VDSL line, represented as an entry in the standard ifTable, along with optional Fast and Interleaved channel statistics when those transport modes are enabled. The MIB is used to monitor the hardware/software health of the VDSL physical layer link, including line rate, signal attenuation/noise margin, and error or defect counters that reveal line quality degradation or loss of sync. It depends on the standard IF-MIB ifTable for interface indexing and follows the IETF VDSL-LINE-MIB definition. It is typically deployed by carriers and enterprises using Cisco DSL access routers or gateways to monitor last-mile broadband line performance, with the CISCO-IETF-VDSL-LINE-MIB MIB providing the standardized object definitions that carriers rely on for that visibility.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-IETF-VDSL-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco VDSL-capable routers/access concentrators
- DSL line cards/modems
- Cisco VDSL access routers/line cards
Monitoring Examples
Each VDSL line appears as a row in the standard ifTable, with additional Fast and Interleaved channel entries when those optional transport modes are configured on the line. An administrator would poll the per-line entries to track sync state, attenuation, and noise margin on a DSL link; a sudden increase in errors or a drop out of a trained/up state signals cable degradation or a modem retrain event. The source excerpt for this MIB did not include specific object names beyond the ifTable linkage described in its MODULE-IDENTITY text, so this example is grounded in that text rather than invented table names.
What Can Be Monitored
- VDSL line sync status
- Fast/Interleaved channel status
- line attenuation and noise margin
- line error/defect counts
This MIB depends on
Related MIBs
Imported Objects
From CISCO-SMI
| ciscoExperiment | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoIetfVdslMIB | 1.3.6.1.4.1.9.10.87 | The MIB module defining objects for the management of a pair of VDSL modems at each end of the VDSL line. Each VDSL line has an entry in an ifTable. An agent may reside at either end of the VDSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) modem at near (Central) end of line Vtur -- (VTUR) modem at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xyzs -- interval of Seconds in which xyz occurs (e.g., xyz=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks, a data unit, see cvdslVtuXChanCrcBlockLength | ||
| G32 cvdslChanCrcBlockLength | 1.3.6.1.4.1.9.10.87.1.1.3.1.2 | Gauge32 | read-only | Indicates the length of the channel data-block on which the CRC operates. |
| cvdslChanEntry | 1.3.6.1.4.1.9.10.87.1.1.3.1 | not-accessible | An entry in the cvdslChanTable. | |
| G32 cvdslChanInterleaveDelay | 1.3.6.1.4.1.9.10.87.1.1.3.1.1 | Gauge32 | read-only | Interleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), the object is not instantiated. |
| cvdslChanTable | 1.3.6.1.4.1.9.10.87.1.1.3 | not-accessible | This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125). | |
| cvdslCompliances | 1.3.6.1.4.1.9.10.87.1.3.2 | |||
| cvdslConformance | 1.3.6.1.4.1.9.10.87.1.3 | |||
| G32 cvdslCurrAtn | 1.3.6.1.4.1.9.10.87.1.1.2.1.6 | Gauge32 | read-only | Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. |
| G32 cvdslCurrAttainableRate | 1.3.6.1.4.1.9.10.87.1.1.2.1.9 | Gauge32 | read-only | Indicates the maximum currently attainable data rate by the Vtu. This value will be equal or greater than the current line rate. |
| INT cvdslCurrOutputPwr | 1.3.6.1.4.1.9.10.87.1.1.2.1.8 | INTEGER | read-only | Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence. |
| INT cvdslCurrSnrMgn | 1.3.6.1.4.1.9.10.87.1.1.2.1.5 | INTEGER | read-only | Noise Margin as seen by this Vtu with respect to its received signal in tenth dB. |
| BIT cvdslCurrStatus | 1.3.6.1.4.1.9.10.87.1.1.2.1.7 | Bits | read-only | Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming Vtu failure due to not receiving valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus. |
| cvdslGroup | 1.3.6.1.4.1.9.10.87.1.3.1.1 | A collection of objects providing information about a VDSL Line. | ||
| cvdslGroups | 1.3.6.1.4.1.9.10.87.1.3.1 | |||
| NTF cvdslInitFailureNotification | 1.3.6.1.4.1.9.10.87.1.0.1 | Vtu initialization failed. See cvdslCurrStatus for potential reasons. | ||
| T/F cvdslInitFailureNotificationEnable | 1.3.6.1.4.1.9.10.87.1.1.16.1.3 | TruthValue | read-create | This object specifies if a cvdslInitFailureNotification notification will be generated if an initialization failure occurs. |
| STR cvdslInvSerialNumber | 1.3.6.1.4.1.9.10.87.1.1.2.1.2 | SnmpAdminString | read-only | The vendor specific string that identifies the vendor equipment. |
| STR cvdslInvVendorID | 1.3.6.1.4.1.9.10.87.1.1.2.1.3 | SnmpAdminString | read-only | The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters. |
| STR cvdslInvVersionNumber | 1.3.6.1.4.1.9.10.87.1.1.2.1.4 | SnmpAdminString | read-only | The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters. |
| I32 cvdslLineAlarmConfProfile | 1.3.6.1.4.1.9.10.87.1.1.1.1.4 | Integer32 | read-write | The value of this object identifies the rows in the VDSL Line Alarm Configuration Profile Table, ( cvdslLineAlarmConfProfileTable ), which apply to this VDSL line, and channels if applicable. |
| cvdslLineAlarmConfProfileEntry | 1.3.6.1.4.1.9.10.87.1.1.16.1 | not-accessible | Each entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| I32 cvdslLineAlarmConfProfileIndex | 1.3.6.1.4.1.9.10.87.1.1.16.1.1 | Integer32 | not-accessible | This object is used by the line alarm configuration table in order to identify a row in that table. The system will always provide a default profile whose index is 1. |
| STR cvdslLineAlarmConfProfileName | 1.3.6.1.4.1.9.10.87.1.1.16.1.2 | SnmpAdminString | read-create | The name for this profile as specified by a user. |
| ROW cvdslLineAlarmConfProfileRowStatus | 1.3.6.1.4.1.9.10.87.1.1.16.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| cvdslLineAlarmConfProfileTable | 1.3.6.1.4.1.9.10.87.1.1.16 | not-accessible | This table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. | |
| CVD cvdslLineCoding | 1.3.6.1.4.1.9.10.87.1.1.1.1.1 | CVdslLineCodingType | read-only | Specifies the VDSL coding type used on this line. |
| I32 cvdslLineConfProfile | 1.3.6.1.4.1.9.10.87.1.1.1.1.3 | Integer32 | read-write | The value of this object identifies the rows in the VDSL Line Configuration Profile Table, ( cvdslLineConfProfileTable ), which apply for this VDSL line, and channels if applicable. |
| cvdslLineConfProfileEntry | 1.3.6.1.4.1.9.10.87.1.1.8.1 | not-accessible | Each entry consists of a list of parameters that represents the configuration of a VDSL modem. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| I32 cvdslLineConfProfileIndex | 1.3.6.1.4.1.9.10.87.1.1.8.1.1 | Integer32 | not-accessible | This object is used by the line configuration table in order to identify a row in that table. The system will always provide a default profile whose value is 1. |
| STR cvdslLineConfProfileName | 1.3.6.1.4.1.9.10.87.1.1.8.1.2 | SnmpAdminString | read-create | The name for this profile as specified by a user. |
| ROW cvdslLineConfProfileRowStatus | 1.3.6.1.4.1.9.10.87.1.1.8.1.6 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. The DEFVAL profile cannot be deleted. |
| cvdslLineConfProfileTable | 1.3.6.1.4.1.9.10.87.1.1.8 | not-accessible | This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. | |
| INT cvdslLineConfRxSpeed | 1.3.6.1.4.1.9.10.87.1.1.8.1.5 | INTEGER | read-create | Receive speed for this modem. The corresponding modem on the other end of the VDSL line will have an equal cvdslLineConfTxSpeed value. |
| INT cvdslLineConfTargetSnrMgn | 1.3.6.1.4.1.9.10.87.1.1.8.1.3 | INTEGER | read-create | Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization. |
| INT cvdslLineConfTxSpeed | 1.3.6.1.4.1.9.10.87.1.1.8.1.4 | INTEGER | read-create | Transmit speed for this modem. The corresponding modem on the other end of the VDSL line will have an equal cvdslLineConfRxSpeed value. |
| cvdslLineEntry | 1.3.6.1.4.1.9.10.87.1.1.1.1 | not-accessible | An entry in the cvdslLineTable. | |
| cvdslLineMCMConfProfileEntry | 1.3.6.1.4.1.9.10.87.1.1.9.1 | not-accessible | Each entry consists of a list of parameters that represents the configuration of a multiple carrier modulation VDSL modem. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileMaxRxPSDEntry | 1.3.6.1.4.1.9.10.87.1.1.14.1 | not-accessible | Each entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileMaxRxPSDTable | 1.3.6.1.4.1.9.10.87.1.1.14 | not-accessible | This table contains maximum receive PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. | |
| cvdslLineMCMConfProfileMaxTxPSDEntry | 1.3.6.1.4.1.9.10.87.1.1.13.1 | not-accessible | Each entry consists of a transmit PSD mask descriptor, which defines the maximum power spectral density (PSD) for a tone. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileMaxTxPSDTable | 1.3.6.1.4.1.9.10.87.1.1.13 | not-accessible | This table contains transmit maximum PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. | |
| cvdslLineMCMConfProfileRxBandEntry | 1.3.6.1.4.1.9.10.87.1.1.11.1 | not-accessible | Each entry consists of a transmit band descriptor, which defines the start and stop bands and the power spectral density (PSD) for that band. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileRxBandTable | 1.3.6.1.4.1.9.10.87.1.1.11 | not-accessible | This table contains receive band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. | |
| cvdslLineMCMConfProfileTable | 1.3.6.1.4.1.9.10.87.1.1.9 | not-accessible | This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. | |
| cvdslLineMCMConfProfileTxBandEntry | 1.3.6.1.4.1.9.10.87.1.1.10.1 | not-accessible | Each entry consists of a transmit band descriptor, which is defined by a start and a stop tone index. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileTxBandTable | 1.3.6.1.4.1.9.10.87.1.1.10 | not-accessible | This table contains transmit band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. | |
| cvdslLineMCMConfProfileTxPSDEntry | 1.3.6.1.4.1.9.10.87.1.1.12.1 | not-accessible | Each entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineMCMConfProfileTxPSDTable | 1.3.6.1.4.1.9.10.87.1.1.12 | not-accessible | This table contains transmit PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. | |
| cvdslLineMib | 1.3.6.1.4.1.9.10.87.1 | |||
| cvdslLineMibCompliance | 1.3.6.1.4.1.9.10.87.1.3.2.1 | The compliance statement for SNMP entities which manage VDSL interfaces. | ||
| cvdslLineSCMConfProfileEntry | 1.3.6.1.4.1.9.10.87.1.1.15.1 | not-accessible | Each entry consists of a list of parameters that represents the configuration of a single carrier modulation VDSL modem. A default profile with an index of 1 will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| cvdslLineSCMConfProfileTable | 1.3.6.1.4.1.9.10.87.1.1.15 | not-accessible | This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. | |
| cvdslLineTable | 1.3.6.1.4.1.9.10.87.1.1.1 | not-accessible | This table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | |
| INT cvdslLineType | 1.3.6.1.4.1.9.10.87.1.1.1.1.2 | INTEGER | read-only | Defines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s). |
| INT cvdslMCMConfProfileMaxRxPSDNumber | 1.3.6.1.4.1.9.10.87.1.1.14.1.1 | INTEGER | not-accessible | The index for this band descriptor entry. |
| INT cvdslMCMConfProfileMaxRxPSDPSD | 1.3.6.1.4.1.9.10.87.1.1.14.1.3 | INTEGER | read-create | Power Spectral Density level in steps of 0.5dB with an offset of -140dbm/Hz. |
| ROW cvdslMCMConfProfileMaxRxPSDRowStatus | 1.3.6.1.4.1.9.10.87.1.1.14.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileMaxRxPSDTone | 1.3.6.1.4.1.9.10.87.1.1.14.1.2 | INTEGER | read-create | The tone index for which the PSD is being specified. |
| INT cvdslMCMConfProfileMaxTxPSDNumber | 1.3.6.1.4.1.9.10.87.1.1.13.1.1 | INTEGER | not-accessible | The index for this band descriptor entry. |
| INT cvdslMCMConfProfileMaxTxPSDPSD | 1.3.6.1.4.1.9.10.87.1.1.13.1.3 | INTEGER | read-create | Power Spectral Density level in steps of 0.5dB with an offset of -140dbm/Hz. |
| ROW cvdslMCMConfProfileMaxTxPSDRowStatus | 1.3.6.1.4.1.9.10.87.1.1.13.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileMaxTxPSDTone | 1.3.6.1.4.1.9.10.87.1.1.13.1.2 | INTEGER | read-create | The tone index for which the PSD is being specified. |
| ROW cvdslMCMConfProfileRowStatus | 1.3.6.1.4.1.9.10.87.1.1.9.1.2 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileRxBandNumber | 1.3.6.1.4.1.9.10.87.1.1.11.1.1 | INTEGER | not-accessible | The index for this band descriptor entry. |
| ROW cvdslMCMConfProfileRxBandRowStatus | 1.3.6.1.4.1.9.10.87.1.1.11.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileRxBandStart | 1.3.6.1.4.1.9.10.87.1.1.11.1.2 | INTEGER | read-create | Start tone index for this band. |
| INT cvdslMCMConfProfileRxBandStop | 1.3.6.1.4.1.9.10.87.1.1.11.1.3 | INTEGER | read-create | Stop tone index for this band. |
| INT cvdslMCMConfProfileTxBandNumber | 1.3.6.1.4.1.9.10.87.1.1.10.1.1 | INTEGER | not-accessible | The index for this band descriptor entry. |
| ROW cvdslMCMConfProfileTxBandRowStatus | 1.3.6.1.4.1.9.10.87.1.1.10.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileTxBandStart | 1.3.6.1.4.1.9.10.87.1.1.10.1.2 | INTEGER | read-create | Start tone index for this band. |
| INT cvdslMCMConfProfileTxBandStop | 1.3.6.1.4.1.9.10.87.1.1.10.1.3 | INTEGER | read-create | Stop tone index for this band. |
| INT cvdslMCMConfProfileTxPSDNumber | 1.3.6.1.4.1.9.10.87.1.1.12.1.1 | INTEGER | not-accessible | The index for this mask descriptor entry. |
| INT cvdslMCMConfProfileTxPSDPSD | 1.3.6.1.4.1.9.10.87.1.1.12.1.3 | INTEGER | read-create | Power Spectral Density level in steps of 0.5dB with an offset of -140dbm/Hz. |
| ROW cvdslMCMConfProfileTxPSDRowStatus | 1.3.6.1.4.1.9.10.87.1.1.12.1.4 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslMCMConfProfileTxPSDTone | 1.3.6.1.4.1.9.10.87.1.1.12.1.2 | INTEGER | read-create | The tone index for which the PSD is being specified. |
| INT cvdslMCMConfProfileTxWindowLength | 1.3.6.1.4.1.9.10.87.1.1.9.1.1 | INTEGER | read-create | Specifies the length of the transmit window, counted in samples at the sampling rate corresponding to the negotiated value of N. |
| cvdslMCMGroup | 1.3.6.1.4.1.9.10.87.1.3.1.2 | A collection of objects providing configuration information for a VDSL line based upon multiple carrier modulation modem. | ||
| cvdslMibObjects | 1.3.6.1.4.1.9.10.87.1.1 | |||
| cvdslNotificationGroup | 1.3.6.1.4.1.9.10.87.1.3.1.4 | This group supports notifications of significant conditions associated with VDSL Lines. | ||
| cvdslNotifications | 1.3.6.1.4.1.9.10.87.1.0 | |||
| cvdslPhysEntry | 1.3.6.1.4.1.9.10.87.1.1.2.1 | not-accessible | An entry in the cvdslPhysTable. | |
| CVD cvdslPhysSide | 1.3.6.1.4.1.9.10.87.1.1.2.1.1 | CVdslLineEntity | not-accessible | Identifies whether the modem is the Vtuc or Vtur. |
| cvdslPhysTable | 1.3.6.1.4.1.9.10.87.1.1.2 | not-accessible | This table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97). | |
| INT cvdslSCMConfProfileCenterFrequency | 1.3.6.1.4.1.9.10.87.1.1.15.1.7 | INTEGER | read-create | Specifies the center frequency profile K. |
| INT cvdslSCMConfProfileConstellationSize | 1.3.6.1.4.1.9.10.87.1.1.15.1.6 | INTEGER | read-create | Specifies the constellation size. |
| INT cvdslSCMConfProfileFastCodewordSize | 1.3.6.1.4.1.9.10.87.1.1.15.1.2 | INTEGER | read-create | Specifies the length in octets of the fast codeword. A value of 0 indicates that the single latency transport class is to be utilized. |
| INT cvdslSCMConfProfileInterleaveDepth | 1.3.6.1.4.1.9.10.87.1.1.15.1.1 | INTEGER | read-create | Specifies the interleaving depth. |
| ROW cvdslSCMConfProfileRowStatus | 1.3.6.1.4.1.9.10.87.1.1.15.1.8 | RowStatus | read-create | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. |
| INT cvdslSCMConfProfileSymbolRateProfile | 1.3.6.1.4.1.9.10.87.1.1.15.1.5 | INTEGER | read-create | The symbol rate profile calculated as S = SR/BSR, where SR is the required symbol rate in kbaud, BSR = 67.5. |
| INT cvdslSCMConfProfileTransmitPSDLevel | 1.3.6.1.4.1.9.10.87.1.1.15.1.4 | INTEGER | read-create | The transmit power spectral density for the VDSL modem. |
| BIT cvdslSCMConfProfileTransmitPSDMask | 1.3.6.1.4.1.9.10.87.1.1.15.1.3 | Bits | read-create | The transmit power spectral density mask code. |
| cvdslSCMGroup | 1.3.6.1.4.1.9.10.87.1.3.1.3 | A collection of objects providing configuration information for a VDSL line based upon single carrier modulation modem. |
RFC description
Implements the IETF VDSL line MIB for managing VDSL interface configuration and statistics on Cisco devices.
Start monitoring Cisco VDSL access routers/line cards with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.