Amperion-MIB

All MIBs › Amperion-MIB

Organization: Amperion

Last Updated: 2003-05-08

Category: Network Interfaces

Description: Amperion broadband over powerline (BPL) network interface and link management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Amperion-MIB?

Amperion-MIB is a private enterprise module for Amperion's Broadband over Powerline (BPL) networking equipment, covering configuration and status of the powerline network interfaces and CPE devices (referred to as 'CD' units) that carry data over electrical wiring. Its data mixes hardware inventory (MAC addresses, hardware/firmware/driver version) with configuration objects (device type, link association) and a device reset control. In monitoring terms it is used to confirm that each powerline CPE unit is online, correctly linked to its parent node, and running expected firmware -- plCdHardwareVersion, plCdFirmwareVersion, and plCdDriverVersion give a software/hardware inventory snapshot useful for spotting devices running outdated or mismatched firmware, while plCdLink shows which network segment a CD unit is associated with. It is a self-contained vendor MIB with the ds2/powerline structure suggesting alignment with DS2 BPL chipset conventions rather than a formal IETF standard. It is deployed on Amperion BPL access points and customer-premises modems used for last-mile broadband delivery over existing power lines, making Amperion-MIB SNMP monitoring the primary way to track CPE firmware and link status across a powerline network.

IPNetwork Monitor allows you to monitor SNMP objects defined in Amperion-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Amperion broadband-over-powerline (BPL) access points and CPE modems

Monitoring Examples

An admin would walk plCdTable/plCdEntry, indexed by plCdIndex, to inventory each powerline CD unit's plCdType, plCdShortMacAddress/plCdLongMacAddress, and plCdLink association, and check plCdFirmwareVersion and plCdHardwareVersion to identify units running outdated firmware. If a CD unit stops responding or shows an unexpected plCdLink value, that would indicate it has dropped off its powerline segment or re-associated unexpectedly. The plCdReset object would then be used remotely to power-cycle a misbehaving unit without a truck roll.

What Can Be Monitored

CD unit hardware/firmware/driver version
CD unit MAC address
powerline link association
device type
remote reset control

Imported Objects

From RFC1213-MIB

ifIndex

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Opaque
TimeTicks
Unsigned32
enterprises

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using afeCpldResetCount OID:

Select an Amperion broadband-over-powerline (BPL) access point or CPE modem (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type afeCpldResetCount into the Find box to locate it in the OID tree, then select it and click OK. It reports afe Cpld Reset Count. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
amperion	1.3.6.1.4.1.13995			Amperion Inc. private MIB
ds2	1.3.6.1.4.1.13995.1
powerline	1.3.6.1.4.1.13995.1.1
plMibIIExtension	1.3.6.1.4.1.13995.1.1.1
plCards	1.3.6.1.4.1.13995.1.1.1.2
I32 plCdNumber	1.3.6.1.4.1.13995.1.1.1.2.1	Integer32	read-only	Number of Cards available. Maximum index of plCdTable
plCdTable	1.3.6.1.4.1.13995.1.1.1.2.2		not-accessible	Powerline Cards Table. List of attributes of each Card available in the System. Indexed by the number of the Card (from 1 to plCdNumber).
plCdEntry	1.3.6.1.4.1.13995.1.1.1.2.2.1		not-accessible	Row of table plCdTable
I32 plCdIndex	1.3.6.1.4.1.13995.1.1.1.2.2.1.1	Integer32	not-accessible	Number of powerline card. Maximum: plCdNumber
INT plCdType	1.3.6.1.4.1.13995.1.1.1.2.2.1.2	INTEGER	read-only	Type of card: 0 => HE 1 => CPE
INT plCdLink	1.3.6.1.4.1.13995.1.1.1.2.2.1.3	INTEGER	read-write	Type of link: 1 => Link 1 2 => Link 2 3 => Link 3 4 => Link 4 5 => Link 5 6 => Link 6
I32 plCdShortMacAddress	1.3.6.1.4.1.13995.1.1.1.2.2.1.4	Integer32	read-write	Short MAC Address of the Card
STR plCdLongMacAddress	1.3.6.1.4.1.13995.1.1.1.2.2.1.5	DisplayString	read-only	Long MAC Address of the Card
STR plCdHardwareVersion	1.3.6.1.4.1.13995.1.1.1.2.2.1.6	DisplayString	read-only	Hardware Version
STR plCdFirmwareVersion	1.3.6.1.4.1.13995.1.1.1.2.2.1.7	DisplayString	read-only	Firmware Version
STR plCdDriverVersion	1.3.6.1.4.1.13995.1.1.1.2.2.1.8	DisplayString	read-only	Driver Version
I32 plCdReset	1.3.6.1.4.1.13995.1.1.1.2.2.1.9	Integer32	read-write	Reset to Saved Values. Soft Reset.
I32 plCdFactoryReset	1.3.6.1.4.1.13995.1.1.1.2.2.1.10	Integer32	read-write	Reset to factory values. Hard Reset.
I32 plCdSaveAsPermanent	1.3.6.1.4.1.13995.1.1.1.2.2.1.11	Integer32	read-write	Save MIB values as default values: the information of the Remote List (long MAC address and short MAC address of each user) is saved and will be restored after a reboot or a poweroff.
I32 plCdStatus	1.3.6.1.4.1.13995.1.1.1.2.2.1.12	Integer32	read-only	Status related to the interface: 0 => OK.
STR plCdRemoteList	1.3.6.1.4.1.13995.1.1.1.2.2.1.13	DisplayString	read-only	List of Long MAC Address that can be connected with HE (only HE). Returns a string with the list of long MAC address (not separated by spaces)
I32 plCdNumRemoteList	1.3.6.1.4.1.13995.1.1.1.2.2.1.14	Integer32	read-only	Number of CPE in remote list (only HE). This is the maximum value for cpeId in Network table.
plNetwork	1.3.6.1.4.1.13995.1.1.2
plNetTable	1.3.6.1.4.1.13995.1.1.2.1		not-accessible	Network Topology. Indexed by number of card and number of remote user (.plCdIndex.cpeId). Maximum values for indexes: plCdNumber and plCdNumRemoteList. Only available in HE.
plNetEntry	1.3.6.1.4.1.13995.1.1.2.1.1		not-accessible	Row of table plNetTable
I32 plNetShortMacAddress	1.3.6.1.4.1.13995.1.1.2.1.1.1	Integer32	not-accessible	SMAC of remote CPE.
STR plNetLongMacAddress	1.3.6.1.4.1.13995.1.1.2.1.1.3	DisplayString	read-create	Long Mac Address of Remote Node.
ROW plNetRowStatus	1.3.6.1.4.1.13995.1.1.2.1.1.8	RowStatus	read-create	Row Status
plTransmission	1.3.6.1.4.1.13995.1.1.3
plInpTable	1.3.6.1.4.1.13995.1.1.3.2		not-accessible	Input Channel Table. Common input characteristics. Indexed by number of card. Maximum value of index: plCdNumber
plInpEntry	1.3.6.1.4.1.13995.1.1.3.2.1		not-accessible	Row of table plInpTable
I32 plInpTotalOctets	1.3.6.1.4.1.13995.1.1.3.2.1.1	Integer32	read-only	Total number of rx octets (including FEC overhead)
I32 plInpGain	1.3.6.1.4.1.13995.1.1.3.2.1.2	Integer32	read-write	Reception gain
INT plInpAGC	1.3.6.1.4.1.13995.1.1.3.2.1.3	INTEGER	read-write	To enable or disable Adaptive Rx Gain Control. 0 => AGC disabled 1 => AGC enabled.
I32 plInpMaxGain	1.3.6.1.4.1.13995.1.1.3.2.1.4	Integer32	read-write	Maximum reception gain
STR plInpThresholds	1.3.6.1.4.1.13995.1.1.3.2.1.5	DisplayString	read-write	SNR Thresholds in dB. Returns a string containing 4 integers.
I32 plInpAttenuationGain	1.3.6.1.4.1.13995.1.1.3.2.1.6	Integer32	read-write	Attenuation Gain (only HE)
I32 plInpSamsDecode	1.3.6.1.4.1.13995.1.1.3.2.1.7	Integer32	read-only	Number of decoded SAMS (only CPE)
I32 plInpSamsGood	1.3.6.1.4.1.13995.1.1.3.2.1.8	Integer32	read-only	Number of used SAMS (only CPE)
I32 plInpSamsBad	1.3.6.1.4.1.13995.1.1.3.2.1.9	Integer32	read-only	Number of discarded SAMS (only CPE)
plInpNodeTable	1.3.6.1.4.1.13995.1.1.3.4		not-accessible	Input Characteristics Remote equipments connected
plInpNodeEntry	1.3.6.1.4.1.13995.1.1.3.4.1		not-accessible	Row of table plInpNodeTable
I32 plInpNodeReceivedPkts	1.3.6.1.4.1.13995.1.1.3.4.1.1	Integer32	read-only	Number of Packets received from cpeId user
I32 plInpNodeReceivedUnrecPkts	1.3.6.1.4.1.13995.1.1.3.4.1.2	Integer32	read-only	Number of Unrecoverable received packets
I32 plInpNodeReceivedCorrectedPkts	1.3.6.1.4.1.13995.1.1.3.4.1.3	Integer32	read-only	Number of Corrected (by FEC) received packets
I32 plInpNodeReceivedOctets	1.3.6.1.4.1.13995.1.1.3.4.1.4	Integer32	read-only	Number of Received bytes
I32 plInpNodeReceivedCorrectedOctets	1.3.6.1.4.1.13995.1.1.3.4.1.5	Integer32	read-only	Number of Corrected (by FEC) received bytes
I32 plInpNodeReceivedPower	1.3.6.1.4.1.13995.1.1.3.4.1.6	Integer32	read-only	Total received power
I32 plInpNodePLR	1.3.6.1.4.1.13995.1.1.3.4.1.7	Integer32	read-only	Packet Loss Rate
I32 plInpNodeMeanBPC	1.3.6.1.4.1.13995.1.1.3.4.1.8	Integer32	read-only	Mean BPC: sum of current bits configuration
I32 plInpNodeSNRChanges	1.3.6.1.4.1.13995.1.1.3.4.1.9	Integer32	read-only	Changes of SNR
STR plInpNodeSNR	1.3.6.1.4.1.13995.1.1.3.4.1.10	DisplayString	read-only	String with SNR per carrier: contains 512 bytes if it is a HE or 768 if it is a CPE.
STR plInpNodeBPC	1.3.6.1.4.1.13995.1.1.3.4.1.11	DisplayString	read-only	String with BPC per carrier configuration: contains 256 bytes if it is a HE or 384 if it is a CPE.
STR plInpNodeCFR	1.3.6.1.4.1.13995.1.1.3.4.1.12	DisplayString	read-only	String with CFR per carrier: contains 512 bytes if it is a HE or 768 if it is a CPE.
STR plInpNodeEnableCarriers	1.3.6.1.4.1.13995.1.1.3.4.1.13	DisplayString	read-write	String with enabled (1) and disabled (0) carriers: contains 256 bytes if it is a HE or 384 if it is a CPE.
STR plInpNodeProtocolEnableCarriers	1.3.6.1.4.1.13995.1.1.3.4.1.14	DisplayString	read-only	String with enabled (1) and disabled (0) carriers: contains 256 bytes if it is a HE or 384 if it is a CPE.
I32 plInpNodeEnableProtocolEnableCarriers	1.3.6.1.4.1.13995.1.1.3.4.1.15	Integer32	read-write	Enable protocol (1) and disable protocol (0).
plTraps	1.3.6.1.4.1.13995.1.1.4
plRemoteCPE	1.3.6.1.4.1.13995.1.1.5
internal	1.3.6.1.4.1.13995.1.2
amperionSystem	1.3.6.1.4.1.13995.2
STR serialNumber	1.3.6.1.4.1.13995.2.1	DisplayString	read-only	The serial number of the board, which is unique per part number
STR partNumber	1.3.6.1.4.1.13995.2.2	DisplayString	read-only	The part number of the board, which identifies the board type
STR rombootVersion	1.3.6.1.4.1.13995.2.3	DisplayString	read-only	The string that identifies the Romboot software
alarms	1.3.6.1.4.1.13995.2.4		not-accessible	Dynamic alarm table - shows all the outstanding alarms on the system
alarmsEntry	1.3.6.1.4.1.13995.2.4.1		not-accessible	Row of table alarms
I32 alarmIndex	1.3.6.1.4.1.13995.2.4.1.1	Integer32	not-accessible	The alarmIndex uniquely identifies alarms on the system
STR description	1.3.6.1.4.1.13995.2.4.1.2	DisplayString	read-only	Textual description of the alarm
INT productType	1.3.6.1.4.1.13995.2.5	INTEGER	read-only	injector/extractor/repeator
STR userGpsInfoString	1.3.6.1.4.1.13995.2.6	DisplayString	read-write	User defined string for the user to put the GPS info of this device
STR linuxVersion	1.3.6.1.4.1.13995.2.8	DisplayString	read-only	The string that identifies the Linux kernel software
STR amperionSysDescr	1.3.6.1.4.1.13995.2.10	DisplayString	read-only	A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
OID amperionSysObjectID	1.3.6.1.4.1.13995.2.11	OBJECT IDENTIFIER	read-only	The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.
TIK amperionSysUpTime	1.3.6.1.4.1.13995.2.12	TimeTicks	read-only	The time (in hundredths of a second) since the network management portion of the system was last re-initialized.
STR amperionSysContact	1.3.6.1.4.1.13995.2.13	DisplayString	read-write	The textual identification of the contact person for this managed node, together with information on how to contact this person.
STR amperionSysName	1.3.6.1.4.1.13995.2.14	DisplayString	read-write	An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
STR amperionSysLocation	1.3.6.1.4.1.13995.2.15	DisplayString	read-write	The physical location of this node (e.g., `telephone closet, 3rd floor').
I32 amperionSysServices	1.3.6.1.4.1.13995.2.16	Integer32	read-only	A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.
IP amperionTrapMgr1	1.3.6.1.4.1.13995.2.18	IpAddress	read-write	IP address of Manager receceiving traps
IP amperionTrapMgr2	1.3.6.1.4.1.13995.2.19	IpAddress	read-write	IP address of Manager receceiving traps
IP amperionTrapMgr3	1.3.6.1.4.1.13995.2.20	IpAddress	read-write	amperionTrapMgr3
softwareUpgrade	1.3.6.1.4.1.13995.3
STR serverAddress	1.3.6.1.4.1.13995.3.1	DisplayString	read-write	Name or IP Address of the primary file server from which to retrieve new software.
STR primaryPartitionContents	1.3.6.1.4.1.13995.3.2	DisplayString	read-only	Description of image in primary partition.
INT currentState	1.3.6.1.4.1.13995.3.3	INTEGER	read-only	Current state of the software upgrade.
INT bootPartition	1.3.6.1.4.1.13995.3.4	INTEGER	read-write	Image in this partition will be used when the system boots.
INT upgradePartition	1.3.6.1.4.1.13995.3.5	INTEGER	read-write	Default partition to erase and load with a new image.
INT currentPartition	1.3.6.1.4.1.13995.3.6	INTEGER	read-only	Partition from which currently running software was loaded.
STR commandOptions	1.3.6.1.4.1.13995.3.7	DisplayString	read-write	Software upgrade options: Reserved for future use
STR backupPartitionContents	1.3.6.1.4.1.13995.3.8	DisplayString	read-only	Description of image in backup partition.
INT primaryCRC	1.3.6.1.4.1.13995.3.9	INTEGER	read-only	CRC status of image in primary partition.
INT backupCRC	1.3.6.1.4.1.13995.3.10	INTEGER	read-only	CRC status of image in backup partition.
STR lastStatus	1.3.6.1.4.1.13995.3.11	DisplayString	read-only	Status of current or last software upgrade performed (since last reboot).
STR filename	1.3.6.1.4.1.13995.3.12	DisplayString	read-write	Path to filename to retrieve for software upgrade
STR server1Address	1.3.6.1.4.1.13995.3.13	DisplayString	read-write	Name or IP Address of the alternate file server from which to retrieve new software.
STR server2Address	1.3.6.1.4.1.13995.3.14	DisplayString	read-write	Name or IP Address of the second alternate file server from which to retrieve new software.
STR upgradeSchedule	1.3.6.1.4.1.13995.3.15	DisplayString	read-write	Scheduled upgrade date and time in MMDDhhmm format.
STR rebootSchedule	1.3.6.1.4.1.13995.3.16	DisplayString	read-write	Scheduled reboot date and time in MMDDhhmm format.
STR login	1.3.6.1.4.1.13995.3.17	DisplayString	read-write	login to use for software upgrade file server access.
STR password	1.3.6.1.4.1.13995.3.18	DisplayString	read-write	password to use for software upgrade file server access.
NTF swupgradeCompleted	1.3.6.1.4.1.13995.3.19			swupgradeCompleted
psGroup	1.3.6.1.4.1.13995.4
INT acLineVoltage	1.3.6.1.4.1.13995.4.1	INTEGER	read-only	State of AC Line voltage (on/off)
STR plus12v	1.3.6.1.4.1.13995.4.2	DisplayString	read-only	Regulated 12 volt supply
STR minus8point5v	1.3.6.1.4.1.13995.4.3	DisplayString	read-only	Regulated -8.5 volt supply
STR plus5v	1.3.6.1.4.1.13995.4.4	DisplayString	read-only	Regulated +5 volt supply
STR plus3point3v	1.3.6.1.4.1.13995.4.5	DisplayString	read-only	Regulated +3.3 volt supply
STR batteryCaseTemp	1.3.6.1.4.1.13995.4.6	DisplayString	read-only	Battery Case Temperature
STR internalMcuTemp	1.3.6.1.4.1.13995.4.7	DisplayString	read-only	Internal Micro Controller Unit Temperature
STR batteryCurrent	1.3.6.1.4.1.13995.4.8	DisplayString	read-only	Battery Current
STR batteryVoltage	1.3.6.1.4.1.13995.4.9	DisplayString	read-only	Battery Voltage
STR mcuSoftwareVersion	1.3.6.1.4.1.13995.4.10	DisplayString	read-only	Micro Controller Unit Software Version
INT powerCycleNpu	1.3.6.1.4.1.13995.4.11	INTEGER	read-write	Power Cycle the Network Processor Unit
INT psMode	1.3.6.1.4.1.13995.4.12	INTEGER	read-only	Power Supply mode, normal mode is protocol; dump mode is a debug mode which displays debug prints from the MCU
INT shutdownNpu	1.3.6.1.4.1.13995.4.13	INTEGER	read-write	Shut down 12v, -8.5v, 3.3v and 5v regulators driving the Network Processor Unit. This should only be used if one of the voltages is too high.
NTF psImageChecksumError	1.3.6.1.4.1.13995.4.14			The power supply is notifying the main digital board that its main image crc is incorrect. The main digital board needs to reprogram the new power supply image again, or revert back to an older good image
NTF criticalBatteryShutdownWarning	1.3.6.1.4.1.13995.4.15			The power supply is warning the main digital board that we have lost AC Line voltage and the battery is running low. The system will be shutting down in seconds. Perform necessary backup.
NTF p12vOutOfRange	1.3.6.1.4.1.13995.4.16			The power supply is warning the main digital board that the +12v regulator is out of range. If the condition is such that it is too high, the decision may be to shutdown the regulator to avoid destroying the hardware
NTF m8point5vOutOfRange	1.3.6.1.4.1.13995.4.17			The power supply is warning the main digital board that the -8.5v regulator is out of range. Note that the -8.5v regulator is the same regulator as the +12v. If the condition is such that it is too high, the decision may be to shutdown the regulator to avoid destroying the hardware.
NTF p5vOutOfRange	1.3.6.1.4.1.13995.4.18			The power supply is warning the main digital board that the +5v regulator is out of range. If the condition is such that it is too high, the decision may be to shutdown the regulator to avoid destroying the hardware.
NTF p3point3vOutOfRange	1.3.6.1.4.1.13995.4.19			The power supply is warning the main digital board that the +3.3v regulator is out of range. If the condition is such that it is too high, the decision may be to shutdown the regulator to avoid destroying the hardware.
NTF batteryVoltsOutOfRange	1.3.6.1.4.1.13995.4.20			The power supply is warning the main digital board that the battery voltage is out of range.
NTF mcuTempOutOfRange	1.3.6.1.4.1.13995.4.21			The power supply is warning the main digital board that the microcontroller unit core temperature is out of range.
NTF batteryTempOutOfRange	1.3.6.1.4.1.13995.4.22			The power supply is warning the main digital board that the battery temperature is out of range
NTF psDetectedCommLapse	1.3.6.1.4.1.13995.4.23			Power Supply notifies main digital board that it did not communnicate to the power supply within the agreed upon periodic interval
NTF criticalRequestAborted	1.3.6.1.4.1.13995.4.24			The power supply is notifying the main digital board that one of the critical requests was aborted due to not receiving it twice in a row.
NTF powerSupplyInternalError	1.3.6.1.4.1.13995.4.25			Power Supply / netmgt (PS thread) detected an internal error condition
NTF psBatteryNotConnected	1.3.6.1.4.1.13995.4.26			Power Supply Battery Not Connected. There is no battery backup for the system.
NTF psAcOnOff	1.3.6.1.4.1.13995.4.27			Power Supply detected AC going ON / OFF
STR psHardwareVersion	1.3.6.1.4.1.13995.4.28	DisplayString	read-only	Hardware Version of the Power SUpply
NTF psHardwareError	1.3.6.1.4.1.13995.4.29			The power supply is notifying the main digital board that it incurred a hardware error
STR psEt	1.3.6.1.4.1.13995.4.30	DisplayString	read-only	Power Supply elapsed time since powerup
STR npuEt	1.3.6.1.4.1.13995.4.31	DisplayString	read-only	Power Supply elapsed time since powerup
I32 npuPuTimes	1.3.6.1.4.1.13995.4.32	Integer32	read-only	Number of times the Network Processing Unit has been powered up.
STR eventDescription	1.3.6.1.4.1.13995.4.33	DisplayString	read-only	Description of the Last Event - Used in sending traps
NTF npuDetectedCommLapse	1.3.6.1.4.1.13995.4.34			Network processing unit could not communnicate to the power supply
amperionInterfaces	1.3.6.1.4.1.13995.5
I32 amperionifNumber	1.3.6.1.4.1.13995.5.1	Integer32	read-only	The number of network interfaces (regardless of their current state) present on this system.
amperionifTable	1.3.6.1.4.1.13995.5.2		not-accessible	A list of interface entries. The number of entries is given by the value of ifNumber.
amperionifEntry	1.3.6.1.4.1.13995.5.2.1		not-accessible	Row of table amperionifTable
T/F amperionWirelessActivate	1.3.6.1.4.1.13995.5.2.1.1	TruthValue	read-write	Command to activate 802.11 parameters on demand.
STR amperionifDescr	1.3.6.1.4.1.13995.5.2.1.2	DisplayString	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
INT amperionifType	1.3.6.1.4.1.13995.5.2.1.3	INTEGER	read-only	The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack.
I32 amperionifMtu	1.3.6.1.4.1.13995.5.2.1.4	Integer32	read-only	The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
G32 amperionifSpeed	1.3.6.1.4.1.13995.5.2.1.5	Gauge32	read-only	An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.
STR amperionifPhysAddress	1.3.6.1.4.1.13995.5.2.1.6	DisplayString	read-only	The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
INT amperionifAdminStatus	1.3.6.1.4.1.13995.5.2.1.7	INTEGER	read-write	The desired state of the interface. The testing(3) state indicates that no operational packets can be passed.
INT amperionifOperStatus	1.3.6.1.4.1.13995.5.2.1.8	INTEGER	read-only	The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.
TIK amperionifLastChange	1.3.6.1.4.1.13995.5.2.1.9	TimeTicks	read-only	The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
C32 amperionifInOctets	1.3.6.1.4.1.13995.5.2.1.10	Counter32	read-only	The total number of octets received on the interface, including framing characters.
C32 amperionifInUcastPkts	1.3.6.1.4.1.13995.5.2.1.11	Counter32	read-only	The number of subnetwork-unicast packets delivered to a higher-layer protocol.
C32 amperionifInNUcastPkts	1.3.6.1.4.1.13995.5.2.1.12	Counter32	read-only	The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
C32 amperionifInDiscards	1.3.6.1.4.1.13995.5.2.1.13	Counter32	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
C32 amperionifInErrors	1.3.6.1.4.1.13995.5.2.1.14	Counter32	read-only	The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
C32 amperionifInUnknownProtos	1.3.6.1.4.1.13995.5.2.1.15	Counter32	read-only	The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
C32 amperionifOutOctets	1.3.6.1.4.1.13995.5.2.1.16	Counter32	read-only	The total number of octets transmitted out of the interface, including framing characters.
C32 amperionifOutUcastPkts	1.3.6.1.4.1.13995.5.2.1.17	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
C32 amperionifOutNUcastPkts	1.3.6.1.4.1.13995.5.2.1.18	Counter32	read-only	The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
C32 amperionifOutDiscards	1.3.6.1.4.1.13995.5.2.1.19	Counter32	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
C32 amperionifOutErrors	1.3.6.1.4.1.13995.5.2.1.20	Counter32	read-only	The number of outbound packets that could not be transmitted because of errors.
G32 amperionifOutQLen	1.3.6.1.4.1.13995.5.2.1.21	Gauge32	read-only	The length of the output packet queue (in packets).
OID amperionifSpecific	1.3.6.1.4.1.13995.5.2.1.22	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
STR amperionWirelessConfigEssid	1.3.6.1.4.1.13995.5.2.1.23	DisplayString	read-write	802.11 network name
INT amperionWirelessConfigMode	1.3.6.1.4.1.13995.5.2.1.24	INTEGER	read-write	802.11 station operational mode
U32 amperionWirelessConfigChanFreq	1.3.6.1.4.1.13995.5.2.1.25	Unsigned32	read-write	802.11 Channel ID
STR amperionWirelessConfigKey	1.3.6.1.4.1.13995.5.2.1.26	DisplayString	read-write	802.11 encryption or scrambling keys and encryption mode.
U32 amperionWirelessLinkQuality	1.3.6.1.4.1.13995.5.2.1.27	Unsigned32	read-only	A measure of how good the received signal is.
U32 amperionWirelessSignalLevel	1.3.6.1.4.1.13995.5.2.1.28	Unsigned32	read-only	Received signal strength (how strong the received signal is).
U32 amperionWirelessNoiseLevel	1.3.6.1.4.1.13995.5.2.1.29	Unsigned32	read-only	Background noise level (when no packet is transmited).
INT amperionWirelessConfigWifType	1.3.6.1.4.1.13995.5.2.1.30	INTEGER	read-write	802.11 protocol type.
I32 amperionWirelessConfigBitRate	1.3.6.1.4.1.13995.5.2.1.31	Integer32	read-write	The bit transmission rate in Megabits per second. (0 = autonegotiated)
STR amperionWirelessConfigWDSPeer	1.3.6.1.4.1.13995.5.2.1.32	DisplayString	read-write	The MAC address of any WDS peer.
NTF interfaceAdminDown	1.3.6.1.4.1.13995.5.3			Admin of Interface being set down
NTF interfaceAdminUp	1.3.6.1.4.1.13995.5.4			Interface is being set up
amperionWireless	1.3.6.1.4.1.13995.6
INT accessControlStatus	1.3.6.1.4.1.13995.6.1	INTEGER	read-write	Status of the access control table
ampMacAcceptTable	1.3.6.1.4.1.13995.6.3		not-accessible	List of Mac address to be accepted
ampMacAcceptEntry	1.3.6.1.4.1.13995.6.3.1		not-accessible	Row of table ampMacAcceptTable
STR macAcceptTableMacAddress	1.3.6.1.4.1.13995.6.3.1.1	DisplayString	read-create	Mac address to be accepted
ROW macAcceptTableRowStatus	1.3.6.1.4.1.13995.6.3.1.2	RowStatus	read-create	Row Status
U32 macAcceptTableIndex	1.3.6.1.4.1.13995.6.3.1.3	Unsigned32	not-accessible	Unique index
U32 macAcceptTableWirelessIf	1.3.6.1.4.1.13995.6.3.1.4	Unsigned32	read-create	The wireless interface (e.g. wlan0) that ACL table is applied to.
amperionipAddrTable	1.3.6.1.4.1.13995.7		not-accessible	The table of addressing information relevant to this entity's IP addresses.
amperionipAddrEntry	1.3.6.1.4.1.13995.7.1		not-accessible	Row of table amperionipAddrTable
IP amperionipAdEntAddr	1.3.6.1.4.1.13995.7.1.1	IpAddress	not-accessible	The IP address to which this entry's addressing information pertains.
STR amperionipAdEntIfName	1.3.6.1.4.1.13995.7.1.2	DisplayString	read-only	The name which uniquely identifies the interface to which this entry is applicable.
IP amperionipAdEntNetMask	1.3.6.1.4.1.13995.7.1.3	IpAddress	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
I32 amperionipAdEntBcastAddr	1.3.6.1.4.1.13995.7.1.4	Integer32	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
I32 amperionipAdEntReasmMaxSize	1.3.6.1.4.1.13995.7.1.5	Integer32	read-only	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
ROW amperionipAdRowStatus	1.3.6.1.4.1.13995.7.1.6	RowStatus	read-create	Row status
T/F amperionipAdEntActivate	1.3.6.1.4.1.13995.7.1.7	TruthValue	read-create	Command to activate the new IP address/netmask on demand.
qualityOfService	1.3.6.1.4.1.13995.8
U32 serviceClassA	1.3.6.1.4.1.13995.8.1	Unsigned32	read-write	Service Class A (Bandwidth in Kbps)
U32 serviceClassB	1.3.6.1.4.1.13995.8.2	Unsigned32	read-write	Service Class B (Bandwidth in Kbps)
U32 serviceClassC	1.3.6.1.4.1.13995.8.3	Unsigned32	read-write	Service Class C (Bandwidth in Kbps)
U32 serviceClassD	1.3.6.1.4.1.13995.8.4	Unsigned32	read-write	Service Class D (Bandwidth in Kbps)
subscriberTable	1.3.6.1.4.1.13995.8.5		not-accessible	List of subscribers
subscriberEntry	1.3.6.1.4.1.13995.8.5.1		not-accessible	Row of table subscriberTable
U32 index	1.3.6.1.4.1.13995.8.5.1.1	Unsigned32	not-accessible	Subscriber unique identification
STR name	1.3.6.1.4.1.13995.8.5.1.2	DisplayString	read-create	Subscriber Name
IP ipAddress	1.3.6.1.4.1.13995.8.5.1.3	IpAddress	read-create	Subscriber IP address
STR macAddress	1.3.6.1.4.1.13995.8.5.1.4	DisplayString	read-create	Subscriber MAC address
INT serviceClass	1.3.6.1.4.1.13995.8.5.1.5	INTEGER	read-create	Subscriber Server Class
ROW rowStatus	1.3.6.1.4.1.13995.8.5.1.6	RowStatus	read-create	A special field used to create new rows.
STR upstreamDownstreamRatio	1.3.6.1.4.1.13995.8.6	DisplayString	read-write	Upstream bandwidth to downstream bandwidth ratio
INT qosStatus	1.3.6.1.4.1.13995.8.7	INTEGER	read-write	Enable or disable status of Qos
afe	1.3.6.1.4.1.13995.9
afeExtractor	1.3.6.1.4.1.13995.9.1
I32 afeExtTxGain	1.3.6.1.4.1.13995.9.1.1	Integer32	read-write	afeExtTxGain
I32 afeExtRxGain	1.3.6.1.4.1.13995.9.1.2	Integer32	read-write	afeExtRxGain
STR afeExtDownstream	1.3.6.1.4.1.13995.9.1.3	DisplayString	read-write	afeExtDownstream
STR afeExtUpstream	1.3.6.1.4.1.13995.9.1.4	DisplayString	read-write	afeExtUpstream
T/F afeExtActivate	1.3.6.1.4.1.13995.9.1.5	TruthValue	read-write	afeExtActivate
afeInjector	1.3.6.1.4.1.13995.9.2
I32 afeInjTxGain	1.3.6.1.4.1.13995.9.2.1	Integer32	read-write	afeInjTxGain
I32 afeInjRxGain	1.3.6.1.4.1.13995.9.2.2	Integer32	read-write	afeInjRxGain
STR afeInjDownstream	1.3.6.1.4.1.13995.9.2.3	DisplayString	read-write	afeInjDownstream
STR afeInjUpstream	1.3.6.1.4.1.13995.9.2.4	DisplayString	read-write	afeInjUpstream
T/F afeInjActivate	1.3.6.1.4.1.13995.9.2.5	TruthValue	read-write	afeInjActivate
amperionRoutes	1.3.6.1.4.1.13995.10
amperionRouteTable	1.3.6.1.4.1.13995.10.1		not-accessible	This entity's IP Routing table.
amperionRouteEntry	1.3.6.1.4.1.13995.10.1.1		not-accessible	Row of table amperionRouteTable
IP ipRouteDest	1.3.6.1.4.1.13995.10.1.1.1	IpAddress	read-only	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
I32 ipRouteIfIndex	1.3.6.1.4.1.13995.10.1.1.2	Integer32	read-write	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
I32 ipRouteMetric1	1.3.6.1.4.1.13995.10.1.1.3	Integer32	read-write	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
I32 ipRouteMetric2	1.3.6.1.4.1.13995.10.1.1.4	Integer32	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
I32 ipRouteMetric3	1.3.6.1.4.1.13995.10.1.1.5	Integer32	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
I32 ipRouteMetric4	1.3.6.1.4.1.13995.10.1.1.6	Integer32	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
IP ipRouteNextHop	1.3.6.1.4.1.13995.10.1.1.7	IpAddress	read-write	The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
INT ipRouteType	1.3.6.1.4.1.13995.10.1.1.8	INTEGER	read-only	The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
INT ipRouteProto	1.3.6.1.4.1.13995.10.1.1.9	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
I32 ipRouteAge	1.3.6.1.4.1.13995.10.1.1.10	Integer32	read-write	The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
IP ipRouteMask	1.3.6.1.4.1.13995.10.1.1.11	IpAddress	read-write	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
I32 ipRouteMetric5	1.3.6.1.4.1.13995.10.1.1.12	Integer32	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
OID ipRouteInfo	1.3.6.1.4.1.13995.10.1.1.13	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
T/F ipDefRouteActivate	1.3.6.1.4.1.13995.10.1.1.14	TruthValue	read-write	Command to activate the new default route.
plc	1.3.6.1.4.1.13995.11
plcExtractor	1.3.6.1.4.1.13995.11.1
I32 plcExtTxGain	1.3.6.1.4.1.13995.11.1.1	Integer32	read-write	plcExtTxGain
I32 plcExtRxGain	1.3.6.1.4.1.13995.11.1.2	Integer32	read-write	plcExtRxGain
plcInjector	1.3.6.1.4.1.13995.11.2
I32 plcInjTxGain	1.3.6.1.4.1.13995.11.2.1	Integer32	read-write	plcInjTxGain
I32 plcInjRxGain	1.3.6.1.4.1.13995.11.2.2	Integer32	read-write	plcInjRxGain
NTF plcUp	1.3.6.1.4.1.13995.11.3			Extractor's PLC interface came up
NTF plcDown	1.3.6.1.4.1.13995.11.4			Extractor's PLC interface went down
C32 afeCpldResetCountEx	1.3.6.1.4.1.13995.11.5	Counter32	read-only	afe Cpld Reset Count
C32 plcLossCount	1.3.6.1.4.1.13995.11.6	Counter32	read-only	plc Loss Count
INT resetCounters	1.3.6.1.4.1.13995.11.7	INTEGER	read-write	reset Counters
optimizationTable	1.3.6.1.4.1.13995.11.8		not-accessible	If Injector - This table contains the frequencies(channels) / gains / throughput of all the extractors down stream. If Extractor - This table should contain frequencies(channels) / gains / throughput for the the plc segment between this extractor and the injector/repeator upstream.
optimizationEntry	1.3.6.1.4.1.13995.11.8.1		not-accessible	Row of table optimizationTable
IP extrIpaddress	1.3.6.1.4.1.13995.11.8.1.1	IpAddress	read-only	extractor's ipaddress
I32 extrChannelNumber	1.3.6.1.4.1.13995.11.8.1.2	Integer32	read-only	Extractor Channel Number
STR upstreamFreq	1.3.6.1.4.1.13995.11.8.1.3	DisplayString	read-only	Upstream Frequency
STR downstreamFreq	1.3.6.1.4.1.13995.11.8.1.4	DisplayString	read-only	Downstream Frequency
STR rxGain	1.3.6.1.4.1.13995.11.8.1.5	DisplayString	read-only	rxGain setting
STR txGain	1.3.6.1.4.1.13995.11.8.1.6	DisplayString	read-only	Tx Gain Setting
STR plcThroughput	1.3.6.1.4.1.13995.11.8.1.7	DisplayString	read-only	plcThroughput
INT upStreamDownStream	1.3.6.1.4.1.13995.11.8.1.8	INTEGER	read-only	This to indicate if this entry pertains to the upstream segment or the downstream segment
STR gpsInfo	1.3.6.1.4.1.13995.11.8.1.9	DisplayString	read-only	GPS co-ordinates. Currently this is a string which means the machine just picks up whatever GPS info is defined in it's system group and sends it to the extractor
STR plcEventDescription	1.3.6.1.4.1.13995.11.9	DisplayString	read-only	String to be sent in the plc up/down event. Will contain ip address of the unit which just went down or will say 'local system' if current system
tempGroup	1.3.6.1.4.1.13995.12
INT tempFanState	1.3.6.1.4.1.13995.12.1	INTEGER	read-only	The fans may be on or off.
I32 tempFanTargetTemp	1.3.6.1.4.1.13995.12.2	Integer32	read-write	The target temperature is the average temperature we would like the system to operate at if possible. It is used to calculate how long the fans should stay on during a cycle which is part of a duty cycle algorithm. Temperature is in degrees celsius.
I32 tempHighWarnLimit	1.3.6.1.4.1.13995.12.3	Integer32	read-write	The system temperature has exceeded a high temperature warning threshold. Temperature is in degrees Celsius.
NTF tempHighWarnLimitTrap	1.3.6.1.4.1.13995.12.4			The system temperature has exceeded the High Warning threshold.
STR tempEventDescription	1.3.6.1.4.1.13995.12.5	DisplayString	read-only	String to be sent with the temperature trap events.
NTF tempHighErrorLimitTrap	1.3.6.1.4.1.13995.12.6			The system temperature has exceeded the High Error Threshold.
NTF tempLowWarnLimitTrap	1.3.6.1.4.1.13995.12.7			The system temperature has gone below the Low Warning Threshold.
NTF tempLowErrorLimitTrap	1.3.6.1.4.1.13995.12.8			The system temperature has gone below the Low Error Threshold.
I32 tempHighErrorLimit	1.3.6.1.4.1.13995.12.9	Integer32	read-write	The system temperature has exceeded a high temperature error threshold. Temperature is in degrees Celsius.
I32 tempLowWarnLimit	1.3.6.1.4.1.13995.12.10	Integer32	read-write	The system temperature has gone below a low temperature warning threshold. Temperature is in degrees Celscius.
I32 tempLowErrorLimit	1.3.6.1.4.1.13995.12.11	Integer32	read-write	The system temperature has gone below the Low Temperature Error Threshold. The temperature is in degrees Celscius.
I32 tempHighWarnHist	1.3.6.1.4.1.13995.12.12	Integer32	read-write	Hysteresis value for the High Temperature Warning Condition. Once the system temperature has reached or exceeded the High Temperature Warning threshold, it must go down to or below the Hysteresis temperature before sending the trap again. The hysteresis temperature is in degrees Celcius.
I32 tempHighErrorHist	1.3.6.1.4.1.13995.12.13	Integer32	read-write	Hysteresis value for the High Temperature Error Condition. Once the system temperature has reached or exceeded the High Temperature Error Threshold, it must go down to or below the Hysteresis temperature before sending the trap again. The hysteresis temperature is in degrees Celcius.
I32 tempLowWarnHist	1.3.6.1.4.1.13995.12.14	Integer32	read-write	Hysteresis value for the Low Temperature Warning Condition. Once the system temperature is less than or equal to the LowTemperature Warning threshold, it must go up to or above the Hysteresis temperature before sending the trap again. The hysteresis temperature is in degrees Celcius.
I32 tempLowErrorHist	1.3.6.1.4.1.13995.12.15	Integer32	read-write	Hysteresis value for the Low Temperature Error Condition. Once the system temperature is less than or equal to the LowTemperature Error threshold, it must go up to or above the Hysteresis temperature before sending the trap again. The hysteresis temperature is in degrees Celcius.
I32 tempSystemTemp	1.3.6.1.4.1.13995.12.16	Integer32	read-only	The temperature of the Main Digital Board. The temperature is obtained by reading a chip located on the digital board.

RFC description

Vendor-private MIB for managing Amperion wireless mesh network devices and RF components.

Start monitoring Amperion broadband-over-powerline (BPL) access points and CPE modems (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Amperion-MIB