| OID symbolic | OID numeric | Type | Access | Description |
|---|
| wsmPortGroup | 1.3.6.1.4.1.800.2.7.1 | | | |
| wsmPortTable | 1.3.6.1.4.1.800.2.7.1.1 | | not-accessible | A table of port layer status and parameter information
for the WSM's physical interfaces. |
| wsmPortEntry | 1.3.6.1.4.1.800.2.7.1.1.1 | | not-accessible | An entry in the table, containing information about
the physical layer of a WSM interface. |
| INT wsmPortSlotIndex | 1.3.6.1.4.1.800.2.7.1.1.1.1 | INTEGER | read-only | A unique value which identifies this HSM board slot. |
| INT wsmPortPortIndex | 1.3.6.1.4.1.800.2.7.1.1.1.2 | INTEGER | read-only | A unique value which identifies this WSM submodule port. |
| INT wsmPortInterfaceType | 1.3.6.1.4.1.800.2.7.1.1.1.3 | INTEGER | read-only | The type of interface on this WSM physical port. |
| INT wsmPortCableType | 1.3.6.1.4.1.800.2.7.1.1.1.4 | INTEGER | read-only | The type of cable attached to the universal serial
port. Non Universal Serial Ports will always return
'unknown'.
NOTE: RS-449 cables will return as RS-530 as
they are detected as the same type. RS-449 is
implemented only as a different connector (DB-37 instead
of DB-25) on the end of the cable. |
| INT wsmPortSerialRxClockPol | 1.3.6.1.4.1.800.2.7.1.1.1.5 | INTEGER | read-write | The receive clock polarity. It is inverted or not inverted.
For interfaces that do not support this, the value
will be stored but ignored. |
| INT wsmPortSerialTxClockPol | 1.3.6.1.4.1.800.2.7.1.1.1.6 | INTEGER | read-write | The Transmit clock polarity. It is inverted or not inverted.
For interfaces that do not support this, the value
will be stored but ignored. |
| INT wsmPortFunctionType | 1.3.6.1.4.1.800.2.7.1.1.1.7 | INTEGER | read-only | The functional capability of the port.
This allows the Manager code to determine the
capabilities of the port so the proper
data can be managed based on the functions
the WAN port can provide.
A 'frameType' port supports layer 2 protocols such
as HDLC and Frame Relay.
A 'cellType' performs ATM interface functions such
as ATM T1 UNI interface.
A 'cbrType' port is used to perform Bit to Cell Conversion
(AAL1). |
| INT wsmPortProtocol | 1.3.6.1.4.1.800.2.7.1.1.1.8 | INTEGER | read-write | The layer 2 protocol of the port.
This parameter only applies when wsmPortFunctionType
is equal to frameType(1).
For ports that don't support this (e.g. Circuit Emulation T1
ports) only a value of none(1) is supported.
For ports that support upper layer protocols (frameType ports)
a value other than none must be used. |
| INT wsmPortIfIndex | 1.3.6.1.4.1.800.2.7.1.1.1.9 | INTEGER | read-only | The ifIndex of the WAN port.
This parameter is used in order to get the physical
port Index used for SNMP standard MIBs that
use ifIndex instead of slot/port. |
| INT wsmPortT1E1StartingTimeSlot | 1.3.6.1.4.1.800.2.7.1.1.1.10 | INTEGER | read-write | Starting TimeSlot for Fractional T1E1 board.
This is only use for Fractional T1E1 board type.
Valid Range: T1: 1..24
E1: 1..31 (May need to skip 16)
The valid range may be effected by
wsmPortT1E1NumberOfTimeSlot too. |
| INT wsmPortT1E1NumberOfTimeSlot | 1.3.6.1.4.1.800.2.7.1.1.1.11 | INTEGER | read-write | Number of TimeSlot for Fractional T1E1 board.
This is only use for Fractional T1E1 board type.
Valid Range: T1: 1..24
E1: 1..31
The valid range may be effected by
wsmPortT1E1NumberOfTimeSlot too. |
| wsmLinkGroup | 1.3.6.1.4.1.800.2.7.2 | | | |
| linkxTable | 1.3.6.1.4.1.800.2.7.2.1 | | not-accessible | A table of WAN link(s) configuration information. |
| linkxEntry | 1.3.6.1.4.1.800.2.7.2.1.1 | | not-accessible | An entry in the WAN link Configuration table,
containing information about a single link's
configuration. |
| INT linkxPeerID | 1.3.6.1.4.1.800.2.7.2.1.1.1 | INTEGER | read-only | The peer ID. This is used as a unique
ID to identify a remote entity and to associate
links to it. For example, for 'normal' PPP, there
is one entry in the link table. For Multilink
PPP there are one or more multiple links.
In either case the Link table is indexed
by Link index (one per link) and by Peer ID.
When one or more entrys in the link table
has the same Peer ID, then these entries
form a group for use either for Multilink
PPP, or as a rotary group. |
| INT linkxIfIndex | 1.3.6.1.4.1.800.2.7.2.1.1.2 | INTEGER | read-only | The ifIndex of the Link. This is used as a unique
ID to identify an individual WAN link entity. |
| STR linkxDescription | 1.3.6.1.4.1.800.2.7.2.1.1.3 | DisplayString | read-write | A description for this WAN link. |
| INT linkxAdminStatus | 1.3.6.1.4.1.800.2.7.2.1.1.4 | INTEGER | read-write | This object controls the Administrative Status
of this WAN Link Entity. Enabled will allow the
Link Entity to operate. Disabled will
disable the Link Entity without deleting it.
Delete will disable the Link entity and delete
the PPP configuration record. |
| INT linkxType | 1.3.6.1.4.1.800.2.7.2.1.1.5 | INTEGER | read-write | The type of link. A wsmPort type is for
WSM serial and Fractional T1 ports. An
ISDN call is for incoming or outgoing
ISDN calls. Additional information
can then be found in Xylan and Standard
MIBs based on the type of the link. |
| INT linkxSlot | 1.3.6.1.4.1.800.2.7.2.1.1.6 | INTEGER | read-write | The slot that is Link is on or zero if the
link is not tied to a given slot (e.g.
for ISDN incoming calls).
If type is wsmPort(1), this must be a non-zero
value. |
| INT linkxPort | 1.3.6.1.4.1.800.2.7.2.1.1.7 | INTEGER | read-write | The port that is Link is on or zero if the
link is not tied to a given port (e.g.
for ISDN incoming calls or Multilink
PPP that requires to run Multilink with
combined serial ports and ISDN calls on
the same slot, but not necessarily fixed
to a given ISDN port on that slot).
If type is wsmPort(1), this must be a non-zero
value. |
| INT linkxMode | 1.3.6.1.4.1.800.2.7.2.1.1.8 | INTEGER | read-write | This object define whether the given link is to be
a On-Demand Link or it is use for Backup. |
