Wellfleet-SYNC-MIB

All MIBs › Wellfleet-SYNC-MIB

Category: Wellfleet BayNetworks WAN Interfaces

Description: Manages Wellfleet synchronous serial interface parameters, clock sources, and synchronization statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-SYNC-MIB?

This is a proprietary Wellfleet Communications MIB for managing synchronous serial WAN interfaces on Wellfleet routers. It exposes configuration objects for clock source selection and interface parameters, plus statistics counters describing synchronization behavior on the link. Administrators use it to monitor the hardware/software health of serial WAN links, including clock synchronization state and error/frame statistics that reveal timing slips or cabling problems. It builds on general interface-table conventions similar to the standard IF-MIB. Typical deployment is on Wellfleet/Bay Networks routers connecting to leased-line or WAN circuits requiring precise clocking (e.g., T1/E1 or V.35 serial links). Engineers can download the Wellfleet-SYNC-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-SYNC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet router
Bay Networks router with synchronous serial WAN interface

Monitoring Examples

An operator would check the configured clock source (internal vs. line/external) and synchronization statistics counters for a serial interface to confirm the link is properly synced to its upstream clock source. Frequent clock-source switchovers or rising error counts would indicate an unstable timing reference or a degrading serial cable/CSU. No concrete sample object names were supplied for this MIB, so this scenario is inferred from its short and module descriptions.

What Can Be Monitored

synchronization clock source
serial interface statistics
clock synchronization status
link error counters

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfLine

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfSyncTable	1.3.6.1.4.1.18.3.4.5		not-accessible	SYNC line record
wfSyncEntry	1.3.6.1.4.1.18.3.4.5.1		not-accessible	An entry in the SYNC table
INT wfSyncDelete	1.3.6.1.4.1.18.3.4.5.1.1	INTEGER	read-write	Create/Delete parameter
INT wfSyncDisable	1.3.6.1.4.1.18.3.4.5.1.2	INTEGER	read-write	Enable/Disable parameter
INT wfSyncState	1.3.6.1.4.1.18.3.4.5.1.3	INTEGER	read-only	Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced with NOTPRES.
INT wfSyncSlot	1.3.6.1.4.1.18.3.4.5.1.4	INTEGER	read-only	Instance ID Slot, filled in by driver
INT wfSyncConnector	1.3.6.1.4.1.18.3.4.5.1.5	INTEGER	read-only	Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connector'. Where 'module' is defined in attribute 86 and 'connector' is defined in attribute 78 of this table. For non-ASN platforms this attribute is the physical connector number on the slot.
INT wfSyncCct	1.3.6.1.4.1.18.3.4.5.1.6	INTEGER	read-write	CCT number for this line instance
INT wfSyncBofl	1.3.6.1.4.1.18.3.4.5.1.7	INTEGER	read-write	breath of life parameter
INT wfSyncBoflTmo	1.3.6.1.4.1.18.3.4.5.1.8	INTEGER	read-write	breath of life timeout in seconds
INT wfSyncMtu	1.3.6.1.4.1.18.3.4.5.1.9	INTEGER	read-write	MTU parameter, this is buffer size for SYNC media, fixed
OCT wfSyncMadr	1.3.6.1.4.1.18.3.4.5.1.10	OCTET STRING	read-only	Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.
INT wfSyncPromiscuous	1.3.6.1.4.1.18.3.4.5.1.11	INTEGER	read-write	The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address are received
INT wfSyncXid	1.3.6.1.4.1.18.3.4.5.1.12	INTEGER	read-write	XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames.
INT wfSyncClkSource	1.3.6.1.4.1.18.3.4.5.1.13	INTEGER	read-write	Tx/Rx clock source is either internally or external generated.
INT wfSyncClkSpeed	1.3.6.1.4.1.18.3.4.5.1.14	INTEGER	read-write	Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected.
INT wfSyncSignalMode	1.3.6.1.4.1.18.3.4.5.1.15	INTEGER	read-write	The signal mode parameter indicates the line paramter balanced or unbalanced.
INT wfSyncRtsEnable	1.3.6.1.4.1.18.3.4.5.1.16	INTEGER	read-write	Note: In KG84 support, RTS has a different meaning
INT wfSyncBurstCount	1.3.6.1.4.1.18.3.4.5.1.17	INTEGER	read-write	Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. The default is always 8 short word bursts (ENABLED). There are only two cases in which this attribute should be changed. Case 1: In certain cases with DSDE and DSE link modules when one or both of the ethernet ports are suffering from excessive TxUflo or RxOflo errors, the BurstCount of one or both SYNC interfaces can be set to single short word bursts (DISABLED). The only modules for which this may be necessary are the DSDE (5430 - Dual Sync, Dual Enet) (module ID 112) and the DSE (5420 - Dual Sync, Single Enet) (module ID 116). If after making the change, the TxUflo or RxOflo errors persist on the ethernet or this SYNC interface starts to get UnderFlowTx or OverFlowRx errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. Case 2: When a SYNC interface on an mk5025 based Link Module is getting UnderFlowTx or OverFlowRx errors while running at bandwidths greater than 2Mbps, the errors may be eliminated by setting this attribute to unlimited burst mode (UNLIMITED). If after making the change, the errors persist or the same errors start on another SYNC interface or one of the ethernet interfaces on the same module starts to get TxUflo or RxOflo errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. For 6Mbps full duplex operation, this attribute will most likely need to be set to UNLIMITED and all other interfaces on this module will most likely have to be deconfigured.
INT wfSyncService	1.3.6.1.4.1.18.3.4.5.1.18	INTEGER	read-write	Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the LAPB protocol service.
INT wfSyncRetryCount	1.3.6.1.4.1.18.3.4.5.1.19	INTEGER	read-write	The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer. This parameter is equal to the N2 counter in ICB.
INT wfSyncLinkIdleTimer	1.3.6.1.4.1.18.3.4.5.1.20	INTEGER	read-write	The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed in seconds.
INT wfSyncRetryTimer	1.3.6.1.4.1.18.3.4.5.1.21	INTEGER	read-write	The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control frames are sent at the expiration of this timer value. The frames will be resent up to retry count (N2) at which time the link will be disconnected.
INT wfSyncExtendedAddress	1.3.6.1.4.1.18.3.4.5.1.22	INTEGER	read-write	This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine the length of address field in octets.
INT wfSyncExtendedAddressForce	1.3.6.1.4.1.18.3.4.5.1.23	INTEGER	read-write	When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. Usefull only in Transparent Mode.
INT wfSyncExtendedControl	1.3.6.1.4.1.18.3.4.5.1.24	INTEGER	read-write	This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead of modulo 8. The control field of U frames remains one octet in length.
INT wfSyncExtendedControlForce	1.3.6.1.4.1.18.3.4.5.1.25	INTEGER	read-write	This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Transparent Mode. (LLC1)
INT wfSyncConnectAttempts	1.3.6.1.4.1.18.3.4.5.1.26	INTEGER	read-write	This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 service.
INT wfSyncWindowSizeTx	1.3.6.1.4.1.18.3.4.5.1.27	INTEGER	read-write	The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode.
INT wfSyncWindowSizeTxExtc	1.3.6.1.4.1.18.3.4.5.1.28	INTEGER	read-write	The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode.
INT wfSyncMinFrameSpace	1.3.6.1.4.1.18.3.4.5.1.29	INTEGER	read-write	The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames.
INT wfSyncLocalAddress	1.3.6.1.4.1.18.3.4.5.1.30	INTEGER	read-write	The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set.
INT wfSyncRemoteAddress	1.3.6.1.4.1.18.3.4.5.1.31	INTEGER	read-write	The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set.
OCT wfSyncPassThruLocalMadr	1.3.6.1.4.1.18.3.4.5.1.32	OCTET STRING	read-write	48 bit MAC address of Local end of Sync Passthru circuit
OCT wfSyncPassThruRemoteMadr	1.3.6.1.4.1.18.3.4.5.1.33	OCTET STRING	read-write	48 bit MAC address of Remote end of Sync Passthru circuit
INT wfSyncWanProtocol	1.3.6.1.4.1.18.3.4.5.1.34	INTEGER	read-write	WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface.
INT wfSyncCrcSize	1.3.6.1.4.1.18.3.4.5.1.35	INTEGER	read-write	CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC
CTR wfSyncRxOctets	1.3.6.1.4.1.18.3.4.5.1.36	Counter	read-only	Number of octets received without error
CTR wfSyncRxFrames	1.3.6.1.4.1.18.3.4.5.1.37	Counter	read-only	Number of frames received without error
CTR wfSyncTxOctets	1.3.6.1.4.1.18.3.4.5.1.38	Counter	read-only	Number of octets transmitted without error
CTR wfSyncTxFrames	1.3.6.1.4.1.18.3.4.5.1.39	Counter	read-only	Number of frames transmitted without error
CTR wfSyncRxErrors	1.3.6.1.4.1.18.3.4.5.1.40	Counter	read-only	Number of receive errors
CTR wfSyncTxErrors	1.3.6.1.4.1.18.3.4.5.1.41	Counter	read-only	Number of transmission errors
CTR wfSyncLackRescRx	1.3.6.1.4.1.18.3.4.5.1.42	Counter	read-only	Number of Rx frames dropped due to lack of buffer resources
CTR wfSyncLackRescTx	1.3.6.1.4.1.18.3.4.5.1.43	Counter	read-only	Number of frames clipped in driver's transmit routine due to transmit congestion.
CTR wfSyncUnderFlowTx	1.3.6.1.4.1.18.3.4.5.1.44	Counter	read-only	Number of transmission underflows, device FIFO went empty before next DMA request was granted.
CTR wfSyncRejectsTx	1.3.6.1.4.1.18.3.4.5.1.45	Counter	read-only	For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in Async mode: Number of frames that grew, due to escaping, larger than a buffer
CTR wfSyncRejectsRx	1.3.6.1.4.1.18.3.4.5.1.46	Counter	read-only	For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a non-matching address For the quicsync driver in Async mode: Number of frames received that did not fit within a buffer
CTR wfSyncOverFlowRx	1.3.6.1.4.1.18.3.4.5.1.47	Counter	read-only	Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available.
CTR wfSyncFramesIncompRx	1.3.6.1.4.1.18.3.4.5.1.48	Counter	read-only	Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors.
CTR wfSyncBadFramesRx	1.3.6.1.4.1.18.3.4.5.1.49	Counter	read-only	Number of bad receive frames, caused by FCS errors or non octet aligned.
CTR wfSyncFrameRejectsRx	1.3.6.1.4.1.18.3.4.5.1.50	Counter	read-only	Number of Frame Rejects received
CTR wfSyncRuntsRx	1.3.6.1.4.1.18.3.4.5.1.51	Counter	read-only	Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception.
CTR wfSyncT1Timeouts	1.3.6.1.4.1.18.3.4.5.1.52	Counter	read-only	Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of the number of timeouts.
CTR wfSyncMemoryErrors	1.3.6.1.4.1.18.3.4.5.1.53	Counter	read-only	Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us.
INT wfSyncMediaType	1.3.6.1.4.1.18.3.4.5.1.54	INTEGER	read-write	Media type selection is provided via this parameter
INT wfSyncCfgTxQueueLength	1.3.6.1.4.1.18.3.4.5.1.55	INTEGER	read-write	Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size.
INT wfSyncCfgRxQueueLength	1.3.6.1.4.1.18.3.4.5.1.56	INTEGER	read-write	Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size.
INT wfSyncTxQueueLength	1.3.6.1.4.1.18.3.4.5.1.57	INTEGER	read-only	Current Transmit Queue Length.
INT wfSyncRxQueueLength	1.3.6.1.4.1.18.3.4.5.1.58	INTEGER	read-only	Current Receive Queue Length.
CTR wfSyncRxReplenMisses	1.3.6.1.4.1.18.3.4.5.1.59	Counter	read-only	Number of packet buffer misses while attempting to replenish driver receive ring.
INT wfSyncStartUpMode	1.3.6.1.4.1.18.3.4.5.1.60	INTEGER	read-write	Initiation of link level for LLC2 running LAPB
INT wfSyncIdleRRFrames	1.3.6.1.4.1.18.3.4.5.1.61	INTEGER	read-write	Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent.
INT wfSyncMultilineMode	1.3.6.1.4.1.18.3.4.5.1.62	INTEGER	read-write	This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard.
INT wfSyncBODExamPeriod	1.3.6.1.4.1.18.3.4.5.1.63	INTEGER	read-write	This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second
INT wfSyncBODFullThreshold	1.3.6.1.4.1.18.3.4.5.1.64	INTEGER	read-write	This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested.
INT wfSyncBODRecoverThreshold	1.3.6.1.4.1.18.3.4.5.1.65	INTEGER	read-write	This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in order for the BOD circuit to revert back to the primary line only. This value should be set to less than one half the value of wfSyncBODFullThreshold to avoid toggling the secondary.
INT wfSyncBODPeriodsToFail	1.3.6.1.4.1.18.3.4.5.1.66	INTEGER	read-write	This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested.
INT wfSyncKG84ACycle	1.3.6.1.4.1.18.3.4.5.1.67	INTEGER	read-write	Monitor sample time in milliseconds
INT wfSyncKG84ASyncLossInterval	1.3.6.1.4.1.18.3.4.5.1.68	INTEGER	read-write	timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization
INT wfSyncKG84ARemoteResyncWait	1.3.6.1.4.1.18.3.4.5.1.69	INTEGER	read-write	when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request
INT wfSyncKG84ASyncPulse	1.3.6.1.4.1.18.3.4.5.1.70	INTEGER	read-write	interval to pulse KG84a SYNC signal, in milliseconds
INT wfSyncKG84AResyncs	1.3.6.1.4.1.18.3.4.5.1.71	INTEGER	read-only	number of KG84 resyncs performed
INT wfSyncKG84AResyncsDetected	1.3.6.1.4.1.18.3.4.5.1.72	INTEGER	read-only	number of KG84 resyncs detected
INT wfSyncKG84ABsu	1.3.6.1.4.1.18.3.4.5.1.73	INTEGER	read-only	value taken from mk5025 sync chip control block
INT wfSyncKG84AState	1.3.6.1.4.1.18.3.4.5.1.74	INTEGER	read-only	state of sync
INT wfSyncKG84AOkFrames	1.3.6.1.4.1.18.3.4.5.1.75	INTEGER	read-only	count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected
INT wfSyncPollingEnable	1.3.6.1.4.1.18.3.4.5.1.76	INTEGER	read-write	Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. If disabled, the DSR lead is ignored.
INT wfSyncBackupPool	1.3.6.1.4.1.18.3.4.5.1.77	INTEGER	read-write	Backup pool id containing this line driver
INT wfSyncDemandPool	1.3.6.1.4.1.18.3.4.5.1.78	INTEGER	read-write	Dial on demand pool id containing this line driver
INT wfSyncLineNumber	1.3.6.1.4.1.18.3.4.5.1.79	INTEGER	read-write	line number for this line instance
INT wfSyncHoldDownTime	1.3.6.1.4.1.18.3.4.5.1.80	INTEGER	read-write	Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a backup configuration and it is a dirty line
INT wfSyncNetworkType	1.3.6.1.4.1.18.3.4.5.1.81	INTEGER	read-write	Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip revision C04. If a customer must be NET2 compliant and is using an MK5025 chip revision C03, the C03 option must be used.
INT wfSyncActiveCct	1.3.6.1.4.1.18.3.4.5.1.82	INTEGER	read-only	Active CCT number for this line instance
INT wfSyncCableType	1.3.6.1.4.1.18.3.4.5.1.83	INTEGER	read-write	Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem
CTR wfSyncRxDropPackets	1.3.6.1.4.1.18.3.4.5.1.84	Counter	read-only	Number of Rx packets dropped by driver.
CTR wfSyncTxDropPackets	1.3.6.1.4.1.18.3.4.5.1.85	Counter	read-only	Number of Tx packets dropped by driver.
INT wfSyncModule	1.3.6.1.4.1.18.3.4.5.1.86	INTEGER	read-only	Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used.
INT wfSyncActualConnector	1.3.6.1.4.1.18.3.4.5.1.87	INTEGER	read-only	Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used.
INT wfSyncLineCoding	1.3.6.1.4.1.18.3.4.5.1.88	INTEGER	read-write	Line Coding for sync interface. Can be either NRZ or NRZI.
TIK wfSyncLastChange	1.3.6.1.4.1.18.3.4.5.1.89	TimeTicks	read-only	The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second) since the network management portion of the system was last re-initialized. Usually the time since boot.
GAU wfSyncOutQLen	1.3.6.1.4.1.18.3.4.5.1.90	Gauge	read-only	The instantaneous current length of the output packet queue (in packets).
INT wfSyncRemoteLpbkDetection	1.3.6.1.4.1.18.3.4.5.1.91	INTEGER	read-write	This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is receiving its own BOFL packets and will bring the interface down assuming that somewhere down stream the link has been put into loopback.
INT wfSyncLastState	1.3.6.1.4.1.18.3.4.5.1.92	INTEGER	read-only	The state which the driver was in prior to the most recent re-initialization.
INT wfSyncExternalClkSpeed	1.3.6.1.4.1.18.3.4.5.1.93	INTEGER	read-write	External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supplied clock. Depending on the protocols configured on this interface, this value may control internal decision making within the router. In some cases, router software uses this attribute for route selection. If Priority Queuing is configured, it chooses queue depths based on this attribute. This attribute has no effect when Internal clocking is configured.
INT wfSyncBChannelOverride	1.3.6.1.4.1.18.3.4.5.1.94	INTEGER	read-write	For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instance id, but the user may override that here, which gives the ability of connecting the B Channel to specific SCC's.
INT wfSyncBChannel	1.3.6.1.4.1.18.3.4.5.1.95	INTEGER	read-only	Indicates which B Channel is running
INT wfSyncForceIFTF	1.3.6.1.4.1.18.3.4.5.1.96	INTEGER	read-write	Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular channel. For SDLC Lines, DEFAULT and FORCE_HDLC_FLAGS both result in HDLC Flags (0x7E) as the fill character. FLAGSTREAMING will cause the fill character to alternate between Flags (0x7E) and Idles (0xFF), depending upon the current state of the line. For ISDN BRI Lines, DEFAULT, FORCE IDLES and FLAGSTREAMING all result in Idles (0xFF) as the fill character. For all other line types, DEFAULT, FORCE HDLC FLAGS and FLAGSTREAMING all result in HDLC Flags (0x7E) as the fill character. Leave this field at the default unless required for the attached device. The AS/400 high speed serial controller requires the use of FLAGSTREAMING for error-free operation.
INT wfSyncPriority	1.3.6.1.4.1.18.3.4.5.1.97	INTEGER	read-write	Used by dial/switched services to assign priority of lines within the same demand or backup pool
INT wfSyncTurboBofl	1.3.6.1.4.1.18.3.4.5.1.98	INTEGER	read-write	DEBUG parameter - Turbo bofl enabled or disabled
INT wfSyncBoflNum	1.3.6.1.4.1.18.3.4.5.1.99	INTEGER	read-write	DEBUG parameter - Number of breath of life packets per breath of life
INT wfSyncBoflLen	1.3.6.1.4.1.18.3.4.5.1.100	INTEGER	read-write	DEBUG parameter - breath of life packet length
INT wfSyncTurboBoflMisses	1.3.6.1.4.1.18.3.4.5.1.101	INTEGER	read-only	DEBUG parameter - breath of life allocation failures
INT wfSyncTurboBoflInvocations	1.3.6.1.4.1.18.3.4.5.1.102	INTEGER	read-only	DEBUG parameter - breath of life invocations
INT wfSyncBandwidthOnDemandPool	1.3.6.1.4.1.18.3.4.5.1.103	INTEGER	read-write	Bandwidth pool id containing this line driver
INT wfSyncBODRecoverPeriodsToPass	1.3.6.1.4.1.18.3.4.5.1.104	INTEGER	read-write	This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line congested. It is used for recovery. That is, once a line is declared as congested, this is the number of consecutive examination periods where the queue depth is below the recovery threshold value required to delare that the line is no longer congested.
STR wfSyncBODHistory	1.3.6.1.4.1.18.3.4.5.1.105	DisplayString	read-only	DEBUG parameter - This is the SBOD history buffer.
INT wfSyncBODDebugFlag	1.3.6.1.4.1.18.3.4.5.1.106	INTEGER	read-write	DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD.
INT wfSyncBChRateAdaption	1.3.6.1.4.1.18.3.4.5.1.107	INTEGER	read-write	This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line mode. This attribute specifies the piece of ISDN line's bandwidth which data from this driver will occupy.
INT wfSyncBChActualRateAdaption	1.3.6.1.4.1.18.3.4.5.1.108	INTEGER	read-only	Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line or dial-up mode. This attribute indicates the speed of this B-channel. It also specifies their bit positions for the case of 56K selections.
INT wfSyncWanType	1.3.6.1.4.1.18.3.4.5.1.109	INTEGER	read-write	This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface.
INT wfSyncAsyncBaudRate	1.3.6.1.4.1.18.3.4.5.1.110	INTEGER	read-write	Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe.
INT wfSyncCfgAsyncCmndMaxIdles	1.3.6.1.4.1.18.3.4.5.1.111	INTEGER	read-write	Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode.
INT wfSyncAsyncCmndMaxIdles	1.3.6.1.4.1.18.3.4.5.1.112	INTEGER	read-only	Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode.
INT wfSyncCfgAsyncDataMaxIdles	1.3.6.1.4.1.18.3.4.5.1.113	INTEGER	read-write	Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode.
INT wfSyncAsyncDataMaxIdles	1.3.6.1.4.1.18.3.4.5.1.114	INTEGER	read-only	Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode.
CTR wfSyncFramesAbortTx	1.3.6.1.4.1.18.3.4.5.1.115	Counter	read-only	Number of frames where CTS was lost during transmission.
INT wfSyncPasyncParityType	1.3.6.1.4.1.18.3.4.5.1.116	INTEGER	read-write	Type of parity chosen for Polled Async
INT wfSyncPasyncCharacterLength	1.3.6.1.4.1.18.3.4.5.1.117	INTEGER	read-write	Number of data bits chosen for Polled Async
INT wfSyncPasyncStopLength	1.3.6.1.4.1.18.3.4.5.1.118	INTEGER	read-write	Number of stop bits chosen for Polled Async
INT wfSyncPasyncBaudRate	1.3.6.1.4.1.18.3.4.5.1.119	INTEGER	read-write	Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe.
INT wfSyncLocalConnectionState	1.3.6.1.4.1.18.3.4.5.1.120	INTEGER	read-only	The state of the cable at the router end.
INT wfSyncRemoteConnectionState	1.3.6.1.4.1.18.3.4.5.1.121	INTEGER	read-only	The state of the cable at the device end.
STR wfSyncTimeSlotAssignment	1.3.6.1.4.1.18.3.4.5.1.122	DisplayString	read-only	Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by the channel assigned to the FT1 card. It contains a list of the timeslots from 1 to 32 for the G.703 card.
INT wfSyncEiaStatus	1.3.6.1.4.1.18.3.4.5.1.123	INTEGER	read-only	The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted, it is marked as a 1. If not asserted, it is marked as a 0. The state of each signal will be updated every second. Bits 0-15 are reserved for actual signal state. Bits 16-31 are reserved for indicating toggling of the signal. Toggling signals are indicated as a 1. Signals not toggling are indicated with a 0. The following signals are defined and monitored: The bit definition as as follows with bit #0 being the LSB. * signal status - bits 0-15 * bit 0 = TXD transmit data 1 = RXD receive data 2 = RTS request to send 3 = CTS clear to send 4 = DSR data set ready 5 = DCD data carrier detect 6 = TXC transmit clock 7 = RXC receive clock 8 = DTR data terminal ready. * signal toggle status bits 16-31 * bit 16 = TXD transmit data 17 = RXD receive data 18 = RTS request to send 19 = CTS clear to send 20 = DSR data set ready 21 = DCD data carrier detect 22 = TXC transmit clock 23 = RXC receive clock 24 = DTR data terminal ready.
INT wfSyncEiaStatusReset	1.3.6.1.4.1.18.3.4.5.1.124	INTEGER	read-write	Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status.
INT wfSyncUcastMap	1.3.6.1.4.1.18.3.4.5.1.125	INTEGER	read-write	Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames.
INT wfSyncAsyncCfgMaxIdleTimer	1.3.6.1.4.1.18.3.4.5.1.126	INTEGER	read-write	Determines if Async Max Idle Timer should be based on the baudrate or on the time needed to receive three characters.

RFC description

Wellfleet synchronous line interface configuration and status monitoring MIB.

Start monitoring Wellfleet router, Bay Networks router with synchronous serial WAN interface (clock-source/sync error-counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-SYNC-MIB

What Is Wellfleet-SYNC-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description