Wellfleet-PPP-MIB

All MIBs › Wellfleet-PPP-MIB

Category: Wellfleet BayNetworks WAN Interfaces

Description: Monitors Wellfleet PPP link control protocol state, NCP negotiations, and serial interface statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-PPP-MIB?

Wellfleet-PPP-MIB is a Wellfleet Communications enterprise MIB for monitoring the Point-to-Point Protocol (PPP) link control protocol (LCP) state, network control protocol (NCP) negotiation outcomes, and serial interface statistics on Wellfleet routers. No module description or sample objects were extracted, so exact object/table names cannot be confirmed, but based on its purpose it would expose per-link PPP negotiation state, negotiated protocol options, and serial-line error/traffic counters. Its monitoring value is centered on WAN link software/protocol health: detecting whether a PPP link has successfully completed LCP/NCP negotiation and is passing traffic cleanly, versus flapping or stuck in a negotiation loop. It likely complements or overlaps conceptually with the standard PPP-MIB group (RFC 1471/1472/1473) although as a Wellfleet-specific module it is not necessarily identical to it. It would be deployed on legacy Wellfleet/Bay Networks routers using PPP-encapsulated serial WAN links. Engineers can download the Wellfleet-PPP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-PPP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet Communications (Bay Networks) routers

Monitoring Examples

No object or table names were available in the extracted metadata for this module, so a concrete monitoring scenario cannot be honestly constructed beyond the general expectation of PPP LCP/NCP state and serial-line statistics implied by the module's short description.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfPppGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfPppLineTable	1.3.6.1.4.1.18.3.5.9.2.1		not-accessible	The Wellfleet PPP Line Configuration Table containing attributes dealing with the link layer and the Link Control Protocol (LCP)
wfPppLineEntry	1.3.6.1.4.1.18.3.5.9.2.1.1		not-accessible	per Wellfleet PPP line configuration parameters and counters
INT wfPppLineDelete	1.3.6.1.4.1.18.3.5.9.2.1.1.1	INTEGER	read-write	Create/Delete parameter
INT wfPppLineDisable	1.3.6.1.4.1.18.3.5.9.2.1.1.2	INTEGER	read-write	Enable/Disable parameter -- Generates Open/Close events to the LCP FSM
INT wfPppLineState	1.3.6.1.4.1.18.3.5.9.2.1.1.3	INTEGER	read-only	PPP state variable, Not Present, Init, Down, Up
INT wfPppLineLineNumber	1.3.6.1.4.1.18.3.5.9.2.1.1.4	INTEGER	read-only	Instance identifier. This is the line number assigned to the driver PPP is running on top of
INT wfPppLineLLIndex	1.3.6.1.4.1.18.3.5.9.2.1.1.5	INTEGER	read-only	Instance identifier. This is the lower layer index presented to PPP by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0.
INT wfPppLineLcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.1.1.6	INTEGER	read-only	the current state of the LCP Finite State Machine
INT wfPppLineRestartTimer	1.3.6.1.4.1.18.3.5.9.2.1.1.7	INTEGER	read-write	value for Restart timer in seconds
INT wfPppLineEchoRequestFreq	1.3.6.1.4.1.18.3.5.9.2.1.1.8	INTEGER	read-write	value for Echo-Request frequency - number of seconds between transmission of Echo-Request packets
INT wfPppLineEchoReplyLoss	1.3.6.1.4.1.18.3.5.9.2.1.1.9	INTEGER	read-write	value for Echo-Reply acceptable loss - number of unacknowledged Echo-Reply packets counted before declaring the link down
INT wfPppLineMaxConfReq	1.3.6.1.4.1.18.3.5.9.2.1.1.10	INTEGER	read-write	value for maximum Configure-Requests - number of Configure-Request packets sent without receiving a valid Configure-Ack, Configure-Nak or Configure-Reject before assuming peer is unable to respond
INT wfPppLineMaxTermReq	1.3.6.1.4.1.18.3.5.9.2.1.1.11	INTEGER	read-write	value for maximum Terminate-Requests - number of Terminate-Request packets sent without receiving a Terminate-Ack before assuming peer is unable to respond
INT wfPppLineMaxConfFail	1.3.6.1.4.1.18.3.5.9.2.1.1.12	INTEGER	read-write	value for maximum configuration failure count - number of Configure-Nak packets sent without sending a Configure-Ack before assuming configuration is unable to converge
CTR wfPppLineMagicNumber	1.3.6.1.4.1.18.3.5.9.2.1.1.13	Counter	read-only	the Magic Number being used on this line
INT wfPppLineMru	1.3.6.1.4.1.18.3.5.9.2.1.1.14	INTEGER	read-only	this is the MRU being used on the line (in both directions)
INT wfPppLineLocalAuthProtocol	1.3.6.1.4.1.18.3.5.9.2.1.1.15	INTEGER	read-write	this is the authorization protocol we require our peer to use on our side of the link
INT wfPppLineRemoteAuthProtocol	1.3.6.1.4.1.18.3.5.9.2.1.1.16	INTEGER	read-only	this is the authorization protocol our peer requires us to use on its side of the link
STR wfPppLineLocalPapId	1.3.6.1.4.1.18.3.5.9.2.1.1.17	DisplayString	read-write	our PAP id - our peer sends this to us in an Authenticate-Request message
STR wfPppLineLocalPapPassword	1.3.6.1.4.1.18.3.5.9.2.1.1.18	DisplayString	read-write	our PAP password - our peer sends this to us in an Authenticate-Request message
STR wfPppLineRemotePapId	1.3.6.1.4.1.18.3.5.9.2.1.1.19	DisplayString	read-write	our peer's PAP id - we send this to our peer in an Authenticate-Request message
STR wfPppLineRemotePapPassword	1.3.6.1.4.1.18.3.5.9.2.1.1.20	DisplayString	read-write	our peer's PAP password - we send this to our peer in an Authenticate-Request message
INT wfPppLineLQProtocol	1.3.6.1.4.1.18.3.5.9.2.1.1.21	INTEGER	read-write	the Link Quality protocol we want to use
INT wfPppLineDisableRemoteLQRTimer	1.3.6.1.4.1.18.3.5.9.2.1.1.22	INTEGER	read-write	enable/disable our peer's LQR timer - this allows for one side to maintain the timer while the other just responds to LQR packets
INT wfPppLineCfgLQRRptPrd	1.3.6.1.4.1.18.3.5.9.2.1.1.23	INTEGER	read-write	this is the value in seconds between transmission of LQR packets (Reporting-Period) - it will be the same on both sides
INT wfPppLineLQRRptPrd	1.3.6.1.4.1.18.3.5.9.2.1.1.24	INTEGER	read-only	this is the Reporting-Period, in seconds, agreed upon during negotiation - we allow the peer to negotiate down from our configured period, our maximum, but not below 1 second
INT wfPppLineCfgInboundQuality	1.3.6.1.4.1.18.3.5.9.2.1.1.25	INTEGER	read-write	the percentage of packets sent by our peer that we've successfully received (over the last 5 LQR Reporting-Periods) - 100 indicates we won't tolerate any loss
INT wfPppLineInboundQuality	1.3.6.1.4.1.18.3.5.9.2.1.1.26	INTEGER	read-only	the current inbound quality
INT wfPppLineCfgOutboundQuality	1.3.6.1.4.1.18.3.5.9.2.1.1.27	INTEGER	read-write	the percentage of packets sent by us that our peer successfully received (over the last 5 LQR Reporting-Periods) - 100 indicates we won't tolerate any loss
INT wfPppLineOutboundQuality	1.3.6.1.4.1.18.3.5.9.2.1.1.28	INTEGER	read-only	the current inbound quality
CTR wfPppLineOutLQRs	1.3.6.1.4.1.18.3.5.9.2.1.1.29	Counter	read-only	the number of Link-Quality-Report packets we've transmitted
CTR wfPppLineInLQRs	1.3.6.1.4.1.18.3.5.9.2.1.1.30	Counter	read-only	the number of Link-Quality-Report packets we've received
STR wfPppLineChapSecret	1.3.6.1.4.1.18.3.5.9.2.1.1.31	DisplayString	read-write	this CHAP secret MUST be the same on both sides of the link if CHAP is used as the Authentication protocol
INT wfPppLinePapFallbackDisable	1.3.6.1.4.1.18.3.5.9.2.1.1.32	INTEGER	read-write	if an attempt to negotiate CHAP fails, enabling this allows a fallback to PAP
STR wfPppLineChapLocalName	1.3.6.1.4.1.18.3.5.9.2.1.1.33	DisplayString	read-write	This attribute is used to assign a local CHAP Name which is used to inform our peer of our identity, during WHOAMI processing
STR wfPppLineChapRemoteName	1.3.6.1.4.1.18.3.5.9.2.1.1.34	DisplayString	read-only	This attribute is used to store our peer's CHAP Name which is used to learn our peer's identity, during WHOAMI processing
INT wfPppLineChapPeriodicTimer	1.3.6.1.4.1.18.3.5.9.2.1.1.35	INTEGER	read-write	Timer for periodic CHAP in seconds. A time of 0 disables Periodic CHAP. This timer value should long enough to allow CHAP to complete one phase before entering another.
CTR wfPppLineBadPackets	1.3.6.1.4.1.18.3.5.9.2.1.1.36	Counter	read-only	These are packets not in correct PPP format
OCT wfPppLineLastBadPacket	1.3.6.1.4.1.18.3.5.9.2.1.1.37	OCTET STRING	read-only	This is the first 16 bytes of the last bad packet we received
CTR wfPppLineLevelPktsIn	1.3.6.1.4.1.18.3.5.9.2.1.1.38	Counter	read-only	This is the count of PPP link-level packets (such as Link Control Protocol or Compression Control Protocl) which have been received.
INT wfPppLineAllowPapReject	1.3.6.1.4.1.18.3.5.9.2.1.1.39	INTEGER	read-write	There are some peers that don't want us asking to be a PAP authenticator, so accept the Reject and remove PAP from the LCP Configure-Request if this is enabled.
INT wfPppLineActiveCct	1.3.6.1.4.1.18.3.5.9.2.1.1.40	INTEGER	read-only	This is the circuit number that this PPP line belongs to For the any switched lines, this will initially be -1
GAU wfPppLineCfgAsyncMap	1.3.6.1.4.1.18.3.5.9.2.1.1.41	Gauge	read-write	This is the initial seed value of Async-Control-Character-Map which will be used for LCP negotiations with the peer.
GAU wfPppLineActualAsyncMap	1.3.6.1.4.1.18.3.5.9.2.1.1.42	Gauge	read-only	Async-Control-Character-Map used by the link to escape control characters in the data packet. This is the result of LCP negotiations with the peer.
INT wfPppLineAuthTimer	1.3.6.1.4.1.18.3.5.9.2.1.1.43	INTEGER	read-write	value for Authentication timer in seconds
INT wfPppLineConvergenceTimer	1.3.6.1.4.1.18.3.5.9.2.1.1.44	INTEGER	read-write	value for Convergence timer in seconds
INT wfPppLineMagicNumDisable	1.3.6.1.4.1.18.3.5.9.2.1.1.45	INTEGER	read-write	Allows Magic Numbers to be disabled on this interface.
INT wfPppLineMyLinkDiscr	1.3.6.1.4.1.18.3.5.9.2.1.1.46	INTEGER	read-write	value of Link Discriminator of this endpoint
INT wfPppLinePeerLinkDiscr	1.3.6.1.4.1.18.3.5.9.2.1.1.47	INTEGER	read-write	value of Link Discriminator of peer's endpoint
INT wfPppLineCfgMru	1.3.6.1.4.1.18.3.5.9.2.1.1.48	INTEGER	read-write	this is the Configured MRU being used on the line
INT wfPppLineRfc1661Compliance	1.3.6.1.4.1.18.3.5.9.2.1.1.49	INTEGER	read-write	Enable/Disable parameter for RFC 1661 compliance
INT wfPppLineLqmCurrentState	1.3.6.1.4.1.18.3.5.9.2.1.1.50	INTEGER	read-only	Indicates whether LQM is running on the line.
wfPppCircuitTable	1.3.6.1.4.1.18.3.5.9.2.2		not-accessible	The Wellfleet PPP Circuit Configuration Table containing attributes dealing with the network layer and each Network Control Protocol (NCP)
wfPppCircuitEntry	1.3.6.1.4.1.18.3.5.9.2.2.1		not-accessible	per Wellfleet circuit PPP configuration parameters and counters
INT wfPppCircuitDelete	1.3.6.1.4.1.18.3.5.9.2.2.1.1	INTEGER	read-write	Create/Delete parameter
INT wfPppCircuitState	1.3.6.1.4.1.18.3.5.9.2.2.1.2	INTEGER	read-only	PPP state variable, Not Present, Init, Down, Up
INT wfPppCircuitIpcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.3	INTEGER	read-only	the current state of the IPCP Finite State Machine
INT wfPppCircuitOsinlcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.4	INTEGER	read-only	the current state of the OSINLCP Finite State Machine
INT wfPppCircuitXnscpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.5	INTEGER	read-only	the current state of the XNSCP Finite State Machine
INT wfPppCircuitDncpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.6	INTEGER	read-only	the current state of the DNCP Finite State Machine
INT wfPppCircuitAtcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.7	INTEGER	read-only	the current state of the ATCP Finite State Machine
INT wfPppCircuitIpxcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.8	INTEGER	read-only	the current state of the IPXCP Finite State Machine
INT wfPppCircuitBncpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.9	INTEGER	read-only	the current state of the BNCP Finite State Machine
INT wfPppCircuitVncpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.10	INTEGER	read-only	the current state of the VNCP Finite State Machine
INT wfPppCircuitID	1.3.6.1.4.1.18.3.5.9.2.2.1.11	INTEGER	read-only	cct number for this instance
INT wfPppCircuitIpDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.12	INTEGER	read-write	enable/disable IP Protocol - disabling generates a Close event to the IPCP FSM and consequently disallows IP traffic on this circuit
INT wfPppCircuitOsinlDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.13	INTEGER	read-write	enable/disable OSI Network Layer Protocol - disabling generates a Close event to the OSINLCP FSM and consequently disallows OSI traffic on this circuit
INT wfPppCircuitXnsDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.14	INTEGER	read-write	enable/disable XNS Protocol - disabling generates a Close event to the XNSCP FSM and consequently disallows XNS traffic on this circuit
INT wfPppCircuitDecnetDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.15	INTEGER	read-write	enable/disable DECnet Protocol - disabling generates a Close event to the DNCP FSM and consequently disallows DECnet traffic on this circuit
INT wfPppCircuitAppletalkDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.16	INTEGER	read-write	enable/disable AppleTalk Protocol - disabling generates a Close event to the ATCP FSM and consequently disallows AppleTalk traffic on this circuit
INT wfPppCircuitIpxDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.17	INTEGER	read-write	enable/disable IPX Protocol - disabling generates a Close event to the IPXCP FSM and consequently disallows IPX traffic on this circuit
INT wfPppCircuitBridgeDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.18	INTEGER	read-write	enable/disable the Bridge - disabling generates a Close event to the BNCP FSM and consequently disallows bridge traffic on this circuit
INT wfPppCircuitVinesDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.19	INTEGER	read-write	enable/disable Vines Protocol - disabling generates a Close event to the VNCP FSM and consequently disallows Vines traffic on this circuit
IP wfPppCircuitCfgLocalIpAddr	1.3.6.1.4.1.18.3.5.9.2.2.1.20	IpAddress	read-write	the IP address we're going to use
IP wfPppCircuitLocalIpAddr	1.3.6.1.4.1.18.3.5.9.2.2.1.21	IpAddress	read-only	the IP address our peer wants us to use
IP wfPppCircuitCfgRemoteIpAddr	1.3.6.1.4.1.18.3.5.9.2.2.1.22	IpAddress	read-write	the IP address we want our peer to use
IP wfPppCircuitRemoteIpAddr	1.3.6.1.4.1.18.3.5.9.2.2.1.23	IpAddress	read-only	the IP address our peer wants to use
OCT wfPppCircuitCfgIpxNetworkNumber	1.3.6.1.4.1.18.3.5.9.2.2.1.24	OCTET STRING	read-write	the configured IPX Network Number to be used by both us and our peer
OCT wfPppCircuitIpxNetworkNumber	1.3.6.1.4.1.18.3.5.9.2.2.1.25	OCTET STRING	read-only	the result of IPX Network Number negotiation
OCT wfPppCircuitIpxRemoteNodeNumber	1.3.6.1.4.1.18.3.5.9.2.2.1.26	OCTET STRING	read-write	this is what we'll tell our peer to use for node number if it sends us a 0
INT wfPppCircuitCfgIpxRoutingProtocol	1.3.6.1.4.1.18.3.5.9.2.2.1.27	INTEGER	read-write	the desired IPX Routing Protocol to be used on the link
INT wfPppCircuitIpxRoutingProtocol	1.3.6.1.4.1.18.3.5.9.2.2.1.28	INTEGER	read-only	the negotiated IPX Routing Protocol to be used on the link
STR wfPppCircuitLocalIpxRouterName	1.3.6.1.4.1.18.3.5.9.2.2.1.29	DisplayString	read-write	our IPX Router Name
STR wfPppCircuitRemoteIpxRouterName	1.3.6.1.4.1.18.3.5.9.2.2.1.30	DisplayString	read-only	our peer's IPX Router Name
INT wfPppCircuitIpxConfigComplete	1.3.6.1.4.1.18.3.5.9.2.2.1.31	INTEGER	read-only	indicates whether or not IPXCP converged on all required options
INT wfPppCircuitCfgAtNetwork	1.3.6.1.4.1.18.3.5.9.2.2.1.32	INTEGER	read-write	the configured AppleTalk network number - our peer must use the same number
INT wfPppCircuitAtNetwork	1.3.6.1.4.1.18.3.5.9.2.2.1.33	INTEGER	read-only	the AppleTalk network number we agreed to use
INT wfPppCircuitCfgLocalAtNode	1.3.6.1.4.1.18.3.5.9.2.2.1.34	INTEGER	read-write	the AppleTalk node number we're configured to use
INT wfPppCircuitLocalAtNode	1.3.6.1.4.1.18.3.5.9.2.2.1.35	INTEGER	read-only	our AppleTalk node number after negotiation
INT wfPppCircuitCfgRemoteAtNode	1.3.6.1.4.1.18.3.5.9.2.2.1.36	INTEGER	read-write	the AppleTalk node number we want our peer to use
INT wfPppCircuitRemoteAtNode	1.3.6.1.4.1.18.3.5.9.2.2.1.37	INTEGER	read-only	our peer's AppleTalk node number after negotiation
INT wfPppCircuitCfgAtRoutingProtocol	1.3.6.1.4.1.18.3.5.9.2.2.1.38	INTEGER	read-write	the desired AppleTalk Routing Protocol to be used on the link
INT wfPppCircuitAtRoutingProtocol	1.3.6.1.4.1.18.3.5.9.2.2.1.39	INTEGER	read-only	the negotiated AppleTalk Routing Protocol to be used on the link
INT wfPppCircuitCfgBridgeEnet	1.3.6.1.4.1.18.3.5.9.2.2.1.40	INTEGER	read-write	allow/disallow Ethernet bridged frames
INT wfPppCircuitBridgeEnet	1.3.6.1.4.1.18.3.5.9.2.2.1.41	INTEGER	read-only	result of bridge MAC type negotiation for Ethernet
INT wfPppCircuitCfgBridgeFddi	1.3.6.1.4.1.18.3.5.9.2.2.1.42	INTEGER	read-write	allow/disallow FDDI bridged frames
INT wfPppCircuitBridgeFddi	1.3.6.1.4.1.18.3.5.9.2.2.1.43	INTEGER	read-only	result of bridge MAC type negotiation for FDDI
INT wfPppCircuitCfgBridgeTokenRing	1.3.6.1.4.1.18.3.5.9.2.2.1.44	INTEGER	read-write	allow/disallow Token Ring bridged frames
INT wfPppCircuitBridgeTokenRing	1.3.6.1.4.1.18.3.5.9.2.2.1.45	INTEGER	read-only	result of bridge MAC type negotiation for Token Ring
CTR wfPppCircuitBadPackets	1.3.6.1.4.1.18.3.5.9.2.2.1.46	Counter	read-only	these are packets not in correct PPP format
OCT wfPppCircuitLastBadPacket	1.3.6.1.4.1.18.3.5.9.2.2.1.47	OCTET STRING	read-only	this is the first 16 bytes of the last bad packet we received
INT wfPppCircuitCcpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.48	INTEGER	read-only	the current state of the CCP Finite State Machine
INT wfPppCircuitCcpDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.49	INTEGER	read-write	enable/disable compression - disabling generates a Close event to the CCP FSM and consequently disallows compression traffic on this circuit
INT wfPppCircuitPppMode	1.3.6.1.4.1.18.3.5.9.2.2.1.50	INTEGER	read-write	Pre 9.0 multilines can only negotiate LCP over 1 line. The exact line which LCP will occur on is unknown. So in order to handle this situation we will wait until we receive an LCP Request before we attempt to negotiate LCP by setting the mode to PPP_MODE_PEER_SOLICITED_LCP_NEGO. If we are using this line as a single PPP Line or we are sure our peer can handle LCP on all the members of the multiline, PPP_MODE_NORMAL should be selected. Multilink is a PPP protocol extension which provides restoration of packets which arrive out of sequence, a possibility with multiple lines. Multilink monitor, in conjunction with other configuration data allows the throughput of a line to be monitored. Additional lines can be brought into the bundle and taken down dynamically in response to data traffic volume and other conditions.
INT wfPppCircuitMLFragPerm	1.3.6.1.4.1.18.3.5.9.2.2.1.51	INTEGER	read-write	This parameter allows interoperability with PPP Multilink implementations which do not allow fragmentation.
INT wfPppCircuitExamPeriod	1.3.6.1.4.1.18.3.5.9.2.2.1.52	INTEGER	read-write	This indicates the interval that the Multilink bundle should be polled for possible congestion. This value is in tenths of a second
INT wfPppCircuitFullThreshold	1.3.6.1.4.1.18.3.5.9.2.2.1.53	INTEGER	read-write	This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested.
INT wfPppCircuitPeriodsCng	1.3.6.1.4.1.18.3.5.9.2.2.1.54	INTEGER	read-write	This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested and attempt corrective action.
INT wfPppCircuitPrefBwSlot	1.3.6.1.4.1.18.3.5.9.2.2.1.55	INTEGER	read-write	This is the preferred bandwidth slot. When lines are requested to be added to the Multilink bundle this parameter denotes the slot which is asked first.
INT wfPppCircuitResvBwSlot	1.3.6.1.4.1.18.3.5.9.2.2.1.56	INTEGER	read-write	This is the reserve bandwidth slot. When lines are requested to be added to the Multilink bundle this parameter denotes the slot which is asked if the preferred slot can not provide a line.
INT wfPppCircuitMLFragTriggerSize	1.3.6.1.4.1.18.3.5.9.2.2.1.57	INTEGER	read-write	This is the minimum size of a packet of which Multilink will fragment.
INT wfPppCircuitMaxLinks	1.3.6.1.4.1.18.3.5.9.2.2.1.58	INTEGER	read-write	This is the maximum number of links allowed in the Multilink bundle for this circuit at any one time.
INT wfPppCircuitRecoverThreshold	1.3.6.1.4.1.18.3.5.9.2.2.1.59	INTEGER	read-write	This is the recovery threshold expressed as a percentage of the theoretical maximum bundle throughput. The actual throughput must fall below this percentage in order for the BOD circuit to begin to remove lines from the Multilink bundle.
INT wfPppCircuitPeriodsUnCng	1.3.6.1.4.1.18.3.5.9.2.2.1.60	INTEGER	read-write	This parameter is used for recovery. Once a Multilink bundle has been declared as congested, this is the number of consecutive examination periods where the queue depth is below the recovery threshold value required to declare that the bundle is no longer congested.
STR wfPppCircuitHistory	1.3.6.1.4.1.18.3.5.9.2.2.1.61	DisplayString	read-only	DEBUG parameter - This is the BOD history buffer.
INT wfPppCircuitDebugFlag	1.3.6.1.4.1.18.3.5.9.2.2.1.62	INTEGER	read-write	DEBUG parameter - This is the BOD Debug flag, used to control debug code for BOD.
INT wfPppCircuitActualMode	1.3.6.1.4.1.18.3.5.9.2.2.1.63	INTEGER	read-only	This attribute is the actual ppp mode of the circuit after LCP has negotiated.
INT wfPppCircuitMaxBuffers	1.3.6.1.4.1.18.3.5.9.2.2.1.64	INTEGER	read-write	This is the maximum number of stored buffers allowed in the Multilink Receive logic for this circuit at any one time.
INT wfPppCircuitLinksConfigured	1.3.6.1.4.1.18.3.5.9.2.2.1.65	INTEGER	read-write	This is the current number of lines configured for this Multilink circuit.
INT wfPppCircuitBacpDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.66	INTEGER	read-write	enable/disable BACP Protocol - disabling generates a Close event to the BACP FSM and consequently disallows BAP traffic on this circuit
INT wfPppCircuitBacpCurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.67	INTEGER	read-only	the current state of the BACP Finite State Machine
INT wfPppCircuitBacpNoPhoneNum	1.3.6.1.4.1.18.3.5.9.2.2.1.68	INTEGER	read-write	enable/disable sending of the No-Phone-Number-Needed option in BACP Call Request packets
INT wfPppCircuitIpv6Disable	1.3.6.1.4.1.18.3.5.9.2.2.1.69	INTEGER	read-write	enable/disable IPv6 Protocol - disabling generates a Close event to the IPv6CP FSM and consequently disallows IPv6 traffic on this circuit
INT wfPppCircuitIpv6CurrentState	1.3.6.1.4.1.18.3.5.9.2.2.1.70	INTEGER	read-only	the current state of the Ipv6 Finite State Machine
INT wfPppCircuitCcpType	1.3.6.1.4.1.18.3.5.9.2.2.1.71	INTEGER	read-write	Specifies whether to use CCP or Individual Link CCP
INT wfPppCircuitCfgCcpOptions	1.3.6.1.4.1.18.3.5.9.2.2.1.72	INTEGER	read-write	Specifies the compression protocol options in 1st config-request
INT wfPppCircuitCcpOptions	1.3.6.1.4.1.18.3.5.9.2.2.1.73	INTEGER	read-only	The negotiated compression protocol option
INT wfPppCircuitStacLZSCheckMode	1.3.6.1.4.1.18.3.5.9.2.2.1.74	INTEGER	read-write	Specifies the check mode for STAC LZS compression protocol. See RFC 1974 for more information.
INT wfPppCircuitMLFragStrict	1.3.6.1.4.1.18.3.5.9.2.2.1.75	INTEGER	read-write	enable/disable strict fragmentation algorithm i.e. fragmenting a packet when its size exceeds the threshold regardless of what the average packet size is
INT wfPppCircuitLampreyCompDisable	1.3.6.1.4.1.18.3.5.9.2.2.1.76	INTEGER	read-write	enable/disable hardware compression, either from the compression daugther card on the Lamprey or the old compression daugther interface card on the link module, it tells you where the compression hardware is
INT wfPppCircuitMsgLevel	1.3.6.1.4.1.18.3.5.9.2.2.1.77	INTEGER	read-write	PPP Circuit log messages level. To control level of log messages DBG_MSG_ALL 0x001f0000 - 2031616 DBG_MSG_DEBUG 0x00010000 - 65536 DBG_MSG_INFO 0x00020000 - 131072 DBG_MSG_WARNING 0x00040000 - 262144 DBG_MSG_FAULT 0x00080000 - 524288 DBG_MSG_TRACE 0x00100000 - 1048576
INT wfPppCircuitType	1.3.6.1.4.1.18.3.5.9.2.2.1.78	INTEGER	read-write	To differentiate between a Dial Up PPP circuit from L2TP and Leased Line
INT wfPppCircuitWRCompatability	1.3.6.1.4.1.18.3.5.9.2.2.1.79	INTEGER	read-write	Enable WebRanger compatability that allows us to accept a config-ack after receiving an invalid config-req
wfPppWhoamiTable	1.3.6.1.4.1.18.3.5.9.2.3		not-accessible	The Wellfleet PPP WHOAMI Table, containing a mapping of peer CHAP Names and the circuit numbers they map to
wfPppWhoamiEntry	1.3.6.1.4.1.18.3.5.9.2.3.1		not-accessible	Map the value of this entry's CHAP Name to the value of this entry's CCT number
INT wfPppWhoamiDelete	1.3.6.1.4.1.18.3.5.9.2.3.1.1	INTEGER	read-write	Create/Delete parameter
STR wfPppWhoamiName	1.3.6.1.4.1.18.3.5.9.2.3.1.2	DisplayString	read-only	Peer CHAP Name
INT wfPppWhoamiCircuit	1.3.6.1.4.1.18.3.5.9.2.3.1.3	INTEGER	read-write	Circuit number to map to
STR wfPppWhoamiSecret	1.3.6.1.4.1.18.3.5.9.2.3.1.4	DisplayString	read-write	Peer CHAP Secret
STR wfPppWhoamiPapPassword	1.3.6.1.4.1.18.3.5.9.2.3.1.5	DisplayString	read-write	Peer Pap Password
INT wfPppWhoamiCctGrp	1.3.6.1.4.1.18.3.5.9.2.3.1.6	INTEGER	read-write	Unnumbered circuit group to map to
wfPppMlStatsTable	1.3.6.1.4.1.18.3.5.9.2.4		not-accessible	The Wellfleet PPP Multilink Stats Table, containing statistics for each Multilink Circuit
wfPppMlStatsEntry	1.3.6.1.4.1.18.3.5.9.2.4.1		not-accessible	per Wellfleet circuit PPP Multilink counters
INT wfPppMlStatsDelete	1.3.6.1.4.1.18.3.5.9.2.4.1.1	INTEGER	read-write	Create/Delete parameter
INT wfPppMlStatsCircuitID	1.3.6.1.4.1.18.3.5.9.2.4.1.2	INTEGER	read-only	cct number for this instance
INT wfPppMlStatsHomeSlot	1.3.6.1.4.1.18.3.5.9.2.4.1.3	INTEGER	read-only	Slot on which this Multilink Control Subsystem exists
GAU wfPppMlStatsLineCnt	1.3.6.1.4.1.18.3.5.9.2.4.1.4	Gauge	read-only	Current count of lines in Multilink bundle
GAU wfPppMlStatsBundleSpd	1.3.6.1.4.1.18.3.5.9.2.4.1.5	Gauge	read-only	Current total bandwidth of Multilink bundle
GAU wfPppMlStatsMrru	1.3.6.1.4.1.18.3.5.9.2.4.1.6	Gauge	read-only	Current Maximum Receive Reconstructed Unit (MRRU) in use for Multilink bundle
OCT wfPppMlStatsEndptDisc	1.3.6.1.4.1.18.3.5.9.2.4.1.7	OCTET STRING	read-only	Current Endpoint Discriminator in use for Multilink bundle
CTR wfPppMlStatsTxOctets	1.3.6.1.4.1.18.3.5.9.2.4.1.8	Counter	read-only	Number of octets transmitted by Multilink
CTR wfPppMlStatsTxPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.9	Counter	read-only	Number of packets transmitted by Multilink
GAU wfPppMlStatsAvgTxListLen	1.3.6.1.4.1.18.3.5.9.2.4.1.10	Gauge	read-only	Average number of packets received in the transient list by the Multilink Transmit gate.
CTR wfPppMlStatsRxOctets	1.3.6.1.4.1.18.3.5.9.2.4.1.11	Counter	read-only	Number of octets received without error
CTR wfPppMlStatsRxPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.12	Counter	read-only	Number of packets received by Multilink
CTR wfPppMlStatsReasmFails	1.3.6.1.4.1.18.3.5.9.2.4.1.13	Counter	read-only	Number of packet reassembly failures
CTR wfPppMlStatsSeqNumberLost	1.3.6.1.4.1.18.3.5.9.2.4.1.14	Counter	read-only	Number of Multilink packets considered to be lost on the wire
CTR wfPppMlStatsSeqNumberArrivedLate	1.3.6.1.4.1.18.3.5.9.2.4.1.15	Counter	read-only	Number of Multilink packets which arrive containing an old Sequence Number. IE: packets with a more current Sequence Number have already been sent up to NCP
GAU wfPppMlStatsReSeqBufferCnt	1.3.6.1.4.1.18.3.5.9.2.4.1.16	Gauge	read-only	Number of Multilink packets currently stored in the ReSequencing buffer pool.
CTR wfPppMlStatsReSeqBufferMax	1.3.6.1.4.1.18.3.5.9.2.4.1.17	Counter	read-only	The Maximum Number of Multilink packets stored in the ReSequencing buffer pool.
CTR wfPppMlStatsExceededBufferMax	1.3.6.1.4.1.18.3.5.9.2.4.1.18	Counter	read-only	The number of times a buffer needed to be stored by the Multilink Receive logic when the count of buffers stored, wfPppMlStatsReSeqBufferMax,was equal to the maximum allowable for this circuit, wfPppCircuitMaxBuffers.
CTR wfPppMlStatsLinkIdleEvents	1.3.6.1.4.1.18.3.5.9.2.4.1.19	Counter	read-only	The number of times the Multilink Receive logic detected a stored buffer received on a line which has been declared idle.
INT wfPppMlStatsCalcPercent	1.3.6.1.4.1.18.3.5.9.2.4.1.20	INTEGER	read-write	enable/disable collection of Rx percentage line usage
INT wfPppMlStatsDebug	1.3.6.1.4.1.18.3.5.9.2.4.1.21	INTEGER	read-write	DEBUG parameter - this is used to control debug code for the Multilink subsystem
GAU wfPppMlStatsReassmBufferCnt	1.3.6.1.4.1.18.3.5.9.2.4.1.22	Gauge	read-only	Number of Multilink packets currently stored in the Reassembling buffer pools.
CTR wfPppMlStatsReassmBufferMax	1.3.6.1.4.1.18.3.5.9.2.4.1.23	Counter	read-only	The Maximum Number of Multilink packets stored in the Reassembling buffer pools.
CTR wfPppMlStatsNumPktsFragmented	1.3.6.1.4.1.18.3.5.9.2.4.1.24	Counter	read-only	The Number of Multilink packets that were fragmented.
CTR wfPppMlStatsPQHiXmits	1.3.6.1.4.1.18.3.5.9.2.4.1.25	Counter	read-only	High priority transmit count.
CTR wfPppMlStatsPQNormalXmits	1.3.6.1.4.1.18.3.5.9.2.4.1.26	Counter	read-only	Normal priority transmit count.
CTR wfPppMlStatsPQLoXmits	1.3.6.1.4.1.18.3.5.9.2.4.1.27	Counter	read-only	Low priority transmit count
CTR wfPppMlStatsPQHiClippedPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.28	Counter	read-only	High priority transmit clip Count
CTR wfPppMlStatsPQNormalClippedPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.29	Counter	read-only	Normal priority transmit clip Count
CTR wfPppMlStatsPQLoClippedPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.30	Counter	read-only	Low priority transmit clip Count
GAU wfPppMlStatsPQIntrQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.31	Gauge	read-only	Interrupt-priority Queue high-water mark
GAU wfPppMlStatsPQHiQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.32	Gauge	read-only	High-priority Queue high-water mark
GAU wfPppMlStatsPQNormalQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.33	Gauge	read-only	Normal-priority Queue high-water mark
GAU wfPppMlStatsPQLoQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.34	Gauge	read-only	Low-priority Queue high-water mark
INT wfPppMlStatsPQHighWaterPktsClear	1.3.6.1.4.1.18.3.5.9.2.4.1.35	INTEGER	read-write	Attribute to clear the high-water marks. When the MIB changes, Priority Queueing (if ENABLED) checks to see if HighWaterPktsClear is different than the last time the MIB was modified in any way. If it is different, all the high water marks (see above) are set to zero.
CTR wfPppMlStatsPQDroppedPkts	1.3.6.1.4.1.18.3.5.9.2.4.1.36	Counter	read-only	Packets which were filtered in Priority Queueing
CTR wfPppMlStatsPQLargePkts	1.3.6.1.4.1.18.3.5.9.2.4.1.37	Counter	read-only	Large Packets which became an exception to latency rules
CTR wfPppMlStatsPQHiTotalOctets	1.3.6.1.4.1.18.3.5.9.2.4.1.38	Counter	read-only	Running total of High Octets transmitted when using Bandwidth Allocation dequeueing algorithm
CTR wfPppMlStatsPQNormalTotalOctets	1.3.6.1.4.1.18.3.5.9.2.4.1.39	Counter	read-only	Running total of Normal Octets transmitted when using Bandwidth Allocation dequeueing algorithm
CTR wfPppMlStatsPQLoTotalOctets	1.3.6.1.4.1.18.3.5.9.2.4.1.40	Counter	read-only	Running total of Low Octets transmitted when using Bandwidth Allocation dequeueing algorithm
CTR wfPppMlStatsPQPktsNotQueued	1.3.6.1.4.1.18.3.5.9.2.4.1.41	Counter	read-only	Packets that were not Queued or Dropped by Priority Queuing
wfPppBapStatsTable	1.3.6.1.4.1.18.3.5.9.2.5		not-accessible	The Wellfleet PPP BAP Stats Table, containing statistics for each BACP Circuit
wfPppBapStatsEntry	1.3.6.1.4.1.18.3.5.9.2.5.1		not-accessible	per Wellfleet circuit PPP BAP counters
INT wfPppBapStatsDelete	1.3.6.1.4.1.18.3.5.9.2.5.1.1	INTEGER	read-write	Create/Delete parameter
INT wfPppBapStatsCircuitID	1.3.6.1.4.1.18.3.5.9.2.5.1.2	INTEGER	read-only	cct number for this instance
CTR wfPppBapCallReqTx	1.3.6.1.4.1.18.3.5.9.2.5.1.3	Counter	read-only	Number of Call Requests transmitted by BAP
CTR wfPppBapCallRespAckTx	1.3.6.1.4.1.18.3.5.9.2.5.1.4	Counter	read-only	Number of Call Responses transmitted by BAP with a Response Code of Request_Ack
CTR wfPppBapCallRespNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.5	Counter	read-only	Number of Call Responses transmitted by BAP with a Response Code of Request_Nak
CTR wfPppBapCallRespFullNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.6	Counter	read-only	Number of Call Responses transmitted by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallRespRejTx	1.3.6.1.4.1.18.3.5.9.2.5.1.7	Counter	read-only	Number of Call Responses transmitted by BAP with a Response Code of Request_Rej
CTR wfPppBapCallbackReqTx	1.3.6.1.4.1.18.3.5.9.2.5.1.8	Counter	read-only	Number of Callback Requests transmitted by BAP
CTR wfPppBapCallbackRespAckTx	1.3.6.1.4.1.18.3.5.9.2.5.1.9	Counter	read-only	Number of Callback Responses transmitted by BAP with a Response Code of Request_Ack
CTR wfPppBapCallbackRespNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.10	Counter	read-only	Number of Callback Responses transmitted by BAP with a Response Code of Request_Nak
CTR wfPppBapCallbackRespFullNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.11	Counter	read-only	Number of Callback Responses transmitted by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallbackRespRejTx	1.3.6.1.4.1.18.3.5.9.2.5.1.12	Counter	read-only	Number of Callback Responses transmitted by BAP with a Response Code of Request_Rej
CTR wfPppBapLdQueryReqTx	1.3.6.1.4.1.18.3.5.9.2.5.1.13	Counter	read-only	Number of LinkDrop Query Requests transmitted by BAP
CTR wfPppBapLdQueryRespAckTx	1.3.6.1.4.1.18.3.5.9.2.5.1.14	Counter	read-only	Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Ack
CTR wfPppBapLdQueryRespNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.15	Counter	read-only	Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Nak
CTR wfPppBapLdQueryRespFullNakTx	1.3.6.1.4.1.18.3.5.9.2.5.1.16	Counter	read-only	Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallStatusIndFailTx	1.3.6.1.4.1.18.3.5.9.2.5.1.17	Counter	read-only	Number of Call_Status_Indications transmitted by BAP with a non-zero Call Status
CTR wfPppBapCallStatusIndSuccessTx	1.3.6.1.4.1.18.3.5.9.2.5.1.18	Counter	read-only	Number of Call_Status_Indications transmitted by BAP with a zero Call Status
CTR wfPppBapCallStatusRespTx	1.3.6.1.4.1.18.3.5.9.2.5.1.19	Counter	read-only	Number of Call_Status_Response transmitted by BAP
CTR wfPppBapCallReqRx	1.3.6.1.4.1.18.3.5.9.2.5.1.20	Counter	read-only	Number of Call Requests received by BAP
CTR wfPppBapCallRespAckRx	1.3.6.1.4.1.18.3.5.9.2.5.1.21	Counter	read-only	Number of Call Responses received by BAP with a Response Code of Request_Ack
CTR wfPppBapCallRespNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.22	Counter	read-only	Number of Call Responses received by BAP with a Response Code of Request_Nak
CTR wfPppBapCallRespFullNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.23	Counter	read-only	Number of Call Responses received by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallRespRejRx	1.3.6.1.4.1.18.3.5.9.2.5.1.24	Counter	read-only	Number of Call Responses received by BAP with a Response Code of Request_Rej
CTR wfPppBapCallbackReqRx	1.3.6.1.4.1.18.3.5.9.2.5.1.25	Counter	read-only	Number of Callback Requests received by BAP
CTR wfPppBapCallbackRespAckRx	1.3.6.1.4.1.18.3.5.9.2.5.1.26	Counter	read-only	Number of Callback Responses received by BAP with a Response Code of Request_Ack
CTR wfPppBapCallbackRespNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.27	Counter	read-only	Number of Callback Responses received by BAP with a Response Code of Request_Nak
CTR wfPppBapCallbackRespFullNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.28	Counter	read-only	Number of Callback Responses received by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallbackRespRejRx	1.3.6.1.4.1.18.3.5.9.2.5.1.29	Counter	read-only	Number of Callback Responses received by BAP with a Response Code of Request_Rej
CTR wfPppBapLdQueryReqRx	1.3.6.1.4.1.18.3.5.9.2.5.1.30	Counter	read-only	Number of LinkDrop Query Requests received by BAP
CTR wfPppBapLdQueryRespAckRx	1.3.6.1.4.1.18.3.5.9.2.5.1.31	Counter	read-only	Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Ack
CTR wfPppBapLdQueryRespNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.32	Counter	read-only	Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Nak
CTR wfPppBapLdQueryRespFullNakRx	1.3.6.1.4.1.18.3.5.9.2.5.1.33	Counter	read-only	Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Full_Nak
CTR wfPppBapCallStatusIndFailRx	1.3.6.1.4.1.18.3.5.9.2.5.1.34	Counter	read-only	Number of Call_Status_Indications received by BAP with a non-zero Call Status
CTR wfPppBapCallStatusIndSuccessRx	1.3.6.1.4.1.18.3.5.9.2.5.1.35	Counter	read-only	Number of Call_Status_Indications received by BAP with a zero Call Status
CTR wfPppBapCallStatusRespRx	1.3.6.1.4.1.18.3.5.9.2.5.1.36	Counter	read-only	Number of Call_Status_Response received by BAP
CTR wfPppBapCallReqRespDiscardRx	1.3.6.1.4.1.18.3.5.9.2.5.1.37	Counter	read-only	Number of Call_Response received by BAP with an old identifier.
CTR wfPppBapCallbackReqRespDiscardRx	1.3.6.1.4.1.18.3.5.9.2.5.1.38	Counter	read-only	Number of Callback_Response received by BAP with an old identifier.

RFC description

Management of Point-to-Point Protocol (PPP) line configuration, Link Control Protocol (LCP) state, and authentication parameters for Wellfleet network interfaces.

Start monitoring Wellfleet Communications (Bay Networks) routers (PPP LCP/NCP negotiation-state status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-PPP-MIB

What Is Wellfleet-PPP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description