Wellfleet-RF-MIB

All MIBs › Wellfleet-RF-MIB

Category: Wellfleet BayNetworks Routing Protocols

Description: Manages Wellfleet route filter configurations, prefix lists, and routing policy match statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-RF-MIB?

Wellfleet-RF-MIB is a Wellfleet/Bay Networks vendor MIB for route filter (RF) configuration, defining prefix lists and routing policy rules used to control which routes are accepted or advertised. It exposes route filter/prefix list definitions and match/hit statistics showing how often each filter rule is applied. Its monitoring value is primarily in confirming routing policy software behavior; a filter with zero matches when traffic is expected, or an unexpectedly high match count, can reveal a misconfigured or overly broad policy affecting route propagation. It works in conjunction with the router's core routing protocol MIBs (e.g., BGP, OSPF) since route filters apply to routes learned or advertised by those protocols. It is deployed on Wellfleet/Bay Networks routers that need fine-grained control over route redistribution and advertisement in enterprise or provider networks. Engineers can download the Wellfleet-RF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-RF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks router

Monitoring Examples

An operator would poll the route filter/prefix list table to confirm the expected prefixes are configured, and check match/hit counters to see how actively each filter is being applied to incoming or outgoing routes. A filter rule showing no hits over time despite matching traffic being expected would suggest a rule ordering or prefix-length mismatch problem. No sample object names were provided for this MIB, so this scenario is inferred from the stated short description.

What Can Be Monitored

route filter/prefix list configuration
routing policy match statistics
filter rule hit counts

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Gauge
IpAddress

From Wellfleet-COMMON-MIB

wfIpGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfIpRfRipImportTable	1.3.6.1.4.1.18.3.5.3.2.1.8		not-accessible	The list of Rip Import Route Filter Rules in IP
wfIpRfRipImportEntry	1.3.6.1.4.1.18.3.5.3.2.1.8.1		not-accessible	An entry in the Rip Import Rule Table
INT wfIpRfRipImportCreate	1.3.6.1.4.1.18.3.5.3.2.1.8.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfRipImportEnable	1.3.6.1.4.1.18.3.5.3.2.1.8.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfRipImportAddress	1.3.6.1.4.1.18.3.5.3.2.1.8.1.3	IpAddress	read-only	The IP address to which this filter applies
IP wfIpRfRipImportMask	1.3.6.1.4.1.18.3.5.3.2.1.8.1.4	IpAddress	read-only	The Mask to which this filter applies. When combined with the Address, a range is specified for application of this rule
INT wfIpRfRipImportAction	1.3.6.1.4.1.18.3.5.3.2.1.8.1.5	INTEGER	read-write	The Action of this Filter
INT wfIpRfRipImportPreference	1.3.6.1.4.1.18.3.5.3.2.1.8.1.6	INTEGER	read-write	The Preference associated with this filter - only valid if accept
IP wfIpRfRipImportRipGateway	1.3.6.1.4.1.18.3.5.3.2.1.8.1.7	IpAddress	read-only	The RIP Gateway to be concerned with
IP wfIpRfRipImportRipInterface	1.3.6.1.4.1.18.3.5.3.2.1.8.1.8	IpAddress	read-only	The IP Network Interface to be concerned with
IP wfIpRfRipImportApplyMask	1.3.6.1.4.1.18.3.5.3.2.1.8.1.9	IpAddress	read-write	The Mask to apply to this route learned instead of the default. NULL means to apply the normal filter
wfIpRfRipExportTable	1.3.6.1.4.1.18.3.5.3.2.1.9		not-accessible	The list of Rip Export Route Filter Rules in IP
wfIpRfRipExportEntry	1.3.6.1.4.1.18.3.5.3.2.1.9.1		not-accessible	An entry in the Rip Export Rule Table
INT wfIpRfRipExportCreate	1.3.6.1.4.1.18.3.5.3.2.1.9.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfRipExportEnable	1.3.6.1.4.1.18.3.5.3.2.1.9.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfRipExportAddress	1.3.6.1.4.1.18.3.5.3.2.1.9.1.3	IpAddress	read-only	The IP address to which this filter applies
IP wfIpRfRipExportMask	1.3.6.1.4.1.18.3.5.3.2.1.9.1.4	IpAddress	read-only	The Mask for the Address Above. When combined with the Address, a range is specified for application of this filter rule
INT wfIpRfRipExportFromProtocol	1.3.6.1.4.1.18.3.5.3.2.1.9.1.5	INTEGER	read-only	The protocol from which this Information is derived
INT wfIpRfRipExportAction	1.3.6.1.4.1.18.3.5.3.2.1.9.1.6	INTEGER	read-write	The action of this export filter; if IP_RF_RIP_EXP_ACTION_AGGREGATE action, the default route, 0.0.0.0, is advertised instead networks that match this filter
IP wfIpRfRipExportInterface	1.3.6.1.4.1.18.3.5.3.2.1.9.1.7	IpAddress	read-only	The optional outbound interface on which to apply this filter
INT wfIpRfRipExportRipMetric	1.3.6.1.4.1.18.3.5.3.2.1.9.1.8	INTEGER	read-write	The optional export RIP metric to apply to this filter. Zero means: use the route's actual cost. Only valid for propagate
wfIpRfOspfImportTable	1.3.6.1.4.1.18.3.5.3.2.1.10		not-accessible	The list of OSPF Import Route Filter Rules in IP
wfIpRfOspfImportEntry	1.3.6.1.4.1.18.3.5.3.2.1.10.1		not-accessible	An entry in the OSPF Import Route Filter Table
INT wfIpRfOspfImportCreate	1.3.6.1.4.1.18.3.5.3.2.1.10.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfOspfImportEnable	1.3.6.1.4.1.18.3.5.3.2.1.10.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfOspfImportAddress	1.3.6.1.4.1.18.3.5.3.2.1.10.1.3	IpAddress	read-only	The IP Address to which this filter applies
IP wfIpRfOspfImportMask	1.3.6.1.4.1.18.3.5.3.2.1.10.1.4	IpAddress	read-only	The Mask to which this filter applies. When combined with the Address, a range is specified for application of this rule
INT wfIpRfOspfImportAction	1.3.6.1.4.1.18.3.5.3.2.1.10.1.5	INTEGER	read-write	The Action of this Filter
INT wfIpRfOspfImportPreference	1.3.6.1.4.1.18.3.5.3.2.1.10.1.6	INTEGER	read-write	The Preference associated with this filter - only valid if accept
INT wfIpRfOspfImportType	1.3.6.1.4.1.18.3.5.3.2.1.10.1.7	INTEGER	read-only	The OSPF route Type to be concerned with. The valid values are null (any route type), 1 (OSPF external type 1), and 2 (OSPF external type 2).
GAU wfIpRfOspfImportTag	1.3.6.1.4.1.18.3.5.3.2.1.10.1.8	Gauge	read-only	The OSPF Tag to be concerned with
wfIpRfOspfExportTable	1.3.6.1.4.1.18.3.5.3.2.1.11		not-accessible	The list of OSPF Export Route Filter Rules in IP
wfIpRfOspfExportEntry	1.3.6.1.4.1.18.3.5.3.2.1.11.1		not-accessible	An entry in the OSPF Export Route Filter Table
INT wfIpRfOspfExportCreate	1.3.6.1.4.1.18.3.5.3.2.1.11.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfOspfExportEnable	1.3.6.1.4.1.18.3.5.3.2.1.11.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfOspfExportAddress	1.3.6.1.4.1.18.3.5.3.2.1.11.1.3	IpAddress	read-only	The IP address to which this filter applies
IP wfIpRfOspfExportMask	1.3.6.1.4.1.18.3.5.3.2.1.11.1.4	IpAddress	read-only	The Mask for the Address Above. When combined with the Address, a range is specified for application of this filter rule
INT wfIpRfOspfExportFromProtocol	1.3.6.1.4.1.18.3.5.3.2.1.11.1.5	INTEGER	read-only	The protocol from which this Information is derived
INT wfIpRfOspfExportAction	1.3.6.1.4.1.18.3.5.3.2.1.11.1.6	INTEGER	read-write	The action of this export filter
INT wfIpRfOspfExportType	1.3.6.1.4.1.18.3.5.3.2.1.11.1.7	INTEGER	read-write	The ospf type to use when this filter matches
GAU wfIpRfOspfExportTag	1.3.6.1.4.1.18.3.5.3.2.1.11.1.8	Gauge	read-write	The ospf tag to use when this filter matches
INT wfIpRfOspfExportAutoTag	1.3.6.1.4.1.18.3.5.3.2.1.11.1.9	INTEGER	read-write	BGP/OSPF automatic tag generation: if enabled, a tag will be generated according to the criteria in RFC 1364. Only valid if wfIpRfOspfExportType is set. If enabled, wfIpRfOspfExportTag is ignored.
wfIpRfEgpImportTable	1.3.6.1.4.1.18.3.5.3.2.1.12		not-accessible	The list of Egp Import Route Filter Rules in IP
wfIpRfEgpImportEntry	1.3.6.1.4.1.18.3.5.3.2.1.12.1		not-accessible	An entry in the Egp Import Rule Table
INT wfIpRfEgpImportCreate	1.3.6.1.4.1.18.3.5.3.2.1.12.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfEgpImportEnable	1.3.6.1.4.1.18.3.5.3.2.1.12.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfEgpImportAddress	1.3.6.1.4.1.18.3.5.3.2.1.12.1.3	IpAddress	read-only	The advertised network to which this filter applies
IP wfIpRfEgpImportMask	1.3.6.1.4.1.18.3.5.3.2.1.12.1.4	IpAddress	read-only	The Mask of the Address to which this filter applies.
INT wfIpRfEgpImportAction	1.3.6.1.4.1.18.3.5.3.2.1.12.1.5	INTEGER	read-write	The Action of this Filter
INT wfIpRfEgpImportPreference	1.3.6.1.4.1.18.3.5.3.2.1.12.1.6	INTEGER	read-write	The Preference associated with this filter - only valid if accept
IP wfIpRfEgpImportPeer	1.3.6.1.4.1.18.3.5.3.2.1.12.1.7	IpAddress	read-only	The Egp Peer to be to be concerned with
INT wfIpRfEgpImportAs	1.3.6.1.4.1.18.3.5.3.2.1.12.1.8	INTEGER	read-only	The Autonomous System number to be concerned with
IP wfIpRfEgpImportGateway	1.3.6.1.4.1.18.3.5.3.2.1.12.1.9	IpAddress	read-only	The EGP gateway to be concerned with
wfIpRfEgpExportTable	1.3.6.1.4.1.18.3.5.3.2.1.13		not-accessible	The list of Egp Export Route Filter Rules in IP
wfIpRfEgpExportEntry	1.3.6.1.4.1.18.3.5.3.2.1.13.1		not-accessible	An entry in the Egp Export Rule Table
INT wfIpRfEgpExportCreate	1.3.6.1.4.1.18.3.5.3.2.1.13.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
INT wfIpRfEgpExportEnable	1.3.6.1.4.1.18.3.5.3.2.1.13.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
IP wfIpRfEgpExportAddress	1.3.6.1.4.1.18.3.5.3.2.1.13.1.3	IpAddress	read-only	The advertised network to which this filter applies
IP wfIpRfEgpExportMask	1.3.6.1.4.1.18.3.5.3.2.1.13.1.4	IpAddress	read-only	The Mask of the Address to which this filter applies.
INT wfIpRfEgpExportFromProtocol	1.3.6.1.4.1.18.3.5.3.2.1.13.1.5	INTEGER	read-only	The protocol from which this Information is derived
INT wfIpRfEgpExportAction	1.3.6.1.4.1.18.3.5.3.2.1.13.1.6	INTEGER	read-write	The action of this export filter
IP wfIpRfEgpExportPeer	1.3.6.1.4.1.18.3.5.3.2.1.13.1.7	IpAddress	read-only	The Egp Peer to be to be concerned with
INT wfIpRfEgpExportOspfType	1.3.6.1.4.1.18.3.5.3.2.1.13.1.8	INTEGER	read-only	The type of route being filtered. This field is only valid if the wfIpRfEgpExportFromProtocol is OSPF. Otherwise, the field is 0.
INT wfIpRfEgpExportOspfTag	1.3.6.1.4.1.18.3.5.3.2.1.13.1.9	INTEGER	read-only	The tag of the route being filtered. This field is only valid if the wfIpRfEgpExportFromProtocol is OSPF. Otherwise, this field is 0.
IP wfIpRfEgpExportInterface	1.3.6.1.4.1.18.3.5.3.2.1.13.1.10	IpAddress	read-write	The optional outbound interface on which to apply this filter
INT wfIpRfEgpExportMetric	1.3.6.1.4.1.18.3.5.3.2.1.13.1.11	INTEGER	read-write	The optional export Egp metric to apply to this filter. Zero means: use the route's actual cost. Only valid for propagate
wfIpRfBgp3ImportTable	1.3.6.1.4.1.18.3.5.3.2.1.14		not-accessible	The table of BGP-3 Import Route Filter Rules
wfIpRfBgp3ImportEntry	1.3.6.1.4.1.18.3.5.3.2.1.14.1		not-accessible	An entry in the BGP-3 Import Rule Table
INT wfIpRfBgp3ImportCreate	1.3.6.1.4.1.18.3.5.3.2.1.14.1.1	INTEGER	read-write	Create/Delete parameter. if set to delete, the rule is removed.
INT wfIpRfBgp3ImportEnable	1.3.6.1.4.1.18.3.5.3.2.1.14.1.2	INTEGER	read-write	Enable/Disable parameter. controls whether the rule is enabled or disabled.
IP wfIpRfBgp3ImportAddress	1.3.6.1.4.1.18.3.5.3.2.1.14.1.3	IpAddress	read-only	The advertised network to which this filter applies. Zero implies `all networks' or the default route, based on wfIpRfBgp3ImportMask.
IP wfIpRfBgp3ImportMask	1.3.6.1.4.1.18.3.5.3.2.1.14.1.4	IpAddress	read-only	The mask applied to wfIpRfBgp3ImportAddress. If zero, this filter applies to all networks. If the address is zero and this parameter is 255.255.255.255, this filter applies to the default route.
INT wfIpRfBgp3ImportAction	1.3.6.1.4.1.18.3.5.3.2.1.14.1.5	INTEGER	read-write	The Action of this Filter
INT wfIpRfBgp3ImportPreference	1.3.6.1.4.1.18.3.5.3.2.1.14.1.6	INTEGER	read-write	The Preference associated with this filter - only valid if accept
INT wfIpRfBgp3ImportPeerAs	1.3.6.1.4.1.18.3.5.3.2.1.14.1.7	INTEGER	read-only	The BGP-3 Peer's AS number (or zero if `any AS')
IP wfIpRfBgp3ImportPeerAddress	1.3.6.1.4.1.18.3.5.3.2.1.14.1.8	IpAddress	read-only	The IP address (not the peer ID) of the peer that this advertisement was received from (zero if `any peer')
INT wfIpRfBgp3ImportOrigAs	1.3.6.1.4.1.18.3.5.3.2.1.14.1.9	INTEGER	read-only	The AS number of the BGP-3 gateway that originated the route (or zero for `any AS')
INT wfIpRfBgp3ImportRouteOrigin	1.3.6.1.4.1.18.3.5.3.2.1.14.1.10	INTEGER	read-only	A value for the ORIGIN path attribute (or zero if not applicable)
GAU wfIpRfBgp3ImportBgp3Preference	1.3.6.1.4.1.18.3.5.3.2.1.14.1.11	Gauge	read-write	The Preference associated with this filter for comparison to other BGP routes only - only valid if accept
wfIpRfBgp3ExportTable	1.3.6.1.4.1.18.3.5.3.2.1.15		not-accessible	The table of BGP-3 Export Route Filter Rules
wfIpRfBgp3ExportEntry	1.3.6.1.4.1.18.3.5.3.2.1.15.1		not-accessible	An entry in the BGP-3 Export Rule Table
INT wfIpRfBgp3ExportCreate	1.3.6.1.4.1.18.3.5.3.2.1.15.1.1	INTEGER	read-write	Create/Delete: if set to delete, the rule is removed
INT wfIpRfBgp3ExportEnable	1.3.6.1.4.1.18.3.5.3.2.1.15.1.2	INTEGER	read-write	Enable/Disable: controls whether the rule is enabled or disabled
IP wfIpRfBgp3ExportAddress	1.3.6.1.4.1.18.3.5.3.2.1.15.1.3	IpAddress	read-only	The advertised network to which this filter applies. Zero implies `all networks' or the default route, based on wfIpRfBgp3ExportMask.
IP wfIpRfBgp3ExportMask	1.3.6.1.4.1.18.3.5.3.2.1.15.1.4	IpAddress	read-only	The mask applied to wfIpRfBgp3ExportAddress. If zero, this filter applies to all networks. If the address is zero and this parameter is 255.255.255.255, this filter applies to the default route.
INT wfIpRfBgp3ExportFromProtocol	1.3.6.1.4.1.18.3.5.3.2.1.15.1.5	INTEGER	read-only	The protocol from which this Information is derived
INT wfIpRfBgp3ExportAction	1.3.6.1.4.1.18.3.5.3.2.1.15.1.6	INTEGER	read-write	The action of this export filter; if IP_RF_BGP3_EXP_ACTION_AGGREGATE action, the default route, 0.0.0.0, is advertised instead networks that match this filter
INT wfIpRfBgp3ExportPeerAs	1.3.6.1.4.1.18.3.5.3.2.1.15.1.7	INTEGER	read-only	The AS number to which the network advertisement is going (zero if `any AS')
IP wfIpRfBgp3ExportPeerAddress	1.3.6.1.4.1.18.3.5.3.2.1.15.1.8	IpAddress	read-only	The IP address (not the peer ID) of the peer that this advertisement is going to (zero if `any peer')
INT wfIpRfBgp3ExportOspfType	1.3.6.1.4.1.18.3.5.3.2.1.15.1.9	INTEGER	read-only	The type of route being filtered. This field is only valid if the wfIpRfEgpExportFromProtocol is OSPF. Otherwise, the field is 0.
INT wfIpRfBgp3ExportOspfTag	1.3.6.1.4.1.18.3.5.3.2.1.15.1.10	INTEGER	read-only	The OSPF tag of the route being filtered. This field is only valid if the wfIpRfBgp3ExportFromProtocol is OSPF and wfIpRfBgp3ExportOspfType is external type 1 or 2. Otherwise, this field is 0.
INT wfIpRfBgp3ExportUseMetric	1.3.6.1.4.1.18.3.5.3.2.1.15.1.11	INTEGER	read-write	Determines whether or not an INTER_AS_METRIC will be advertised for the associated network(s). none (1) indicates that no metric will be advertised. specified (2) indicates that the value in wfIpRfBgp3ExportInterAsMetric will be used. originating (3) indicates that the metric from the originating protocol will be used. Only valid for propagate.
INT wfIpRfBgp3ExportInterAsMetric	1.3.6.1.4.1.18.3.5.3.2.1.15.1.12	INTEGER	read-write	If wfIpRfBgp3ExportUseMetric is set to specified (2), this is the value that will be used for the INTER_AS_METRIC. Only valid for propagate.
INT wfIpRfBgp3ExportOrigin	1.3.6.1.4.1.18.3.5.3.2.1.15.1.13	INTEGER	read-write	The value to use for the ORIGIN path attribute when advertising this route (zero means `do according to default'). Only valid for propagate action. Only valid if route origin is RIP or STATIC (ignored otherwise).
INT wfIpRfBgp3ExportNeighAs	1.3.6.1.4.1.18.3.5.3.2.1.15.1.14	INTEGER	read-write	If action is propagate, route origin is RIP or STATIC, and ExportOrigin is EGP, this AS number is used as the EGP neighbor AS number when constructing the AS-PATH (ignored otherwise).

RFC description

Configures RIP import route filter rules on Wellfleet network devices. Enables control of route advertisements and preferences based on IP address masks and gateways.

Start monitoring Wellfleet/Bay Networks router (route-filter/prefix-list match-count status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-RF-MIB

What Is Wellfleet-RF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description