UBQS-IP-MIB

All MIBs › UBQS-IP-MIB

Organization: Ubiquoss Corp.

Last Updated: 2010-12-28

Category: Ubiquoss Enterprise Networking

Description: Manages Ubiquoss IP routing configuration, address management, and IP forwarding table entries.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is UBQS-IP-MIB?

UBQS-IP-MIB is a Ubiquoss enterprise MIB providing IP-layer management objects for Ubiquoss switches and access devices, covering IP routing/address configuration together with an embedded SNMP-controlled ping utility. It exposes objects for IP forwarding-table and address management (ubiIpMIBObjects) alongside a ping subsystem (ubiPingMIBObjects, ubiPingGlobal, ubiPingSend) that lets the device originate ICMP echo tests on command. It is used to monitor IP configuration correctness and network reachability — an operator triggers ubiPingSend and reads back the results to confirm whether a remote host or gateway is reachable from the device, functioning as a lightweight software-level connectivity health check rather than a physical hardware sensor. It likely relies on standard IP-MIB (RFC 4293) conventions for its base IP-addressing concepts even though it defines its own enterprise objects. It is typically deployed on Ubiquoss switches/routers in service-provider or enterprise access networks where remote reachability diagnostics via SNMP are useful. Engineers can download the UBQS-IP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UBQS-IP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ubiquoss switches/access routers

Monitoring Examples

An operator would configure and trigger a test via ubiPingSend under ubiPingGlobal, specifying a target address, then poll the resulting ping status/statistics to determine round-trip success; repeated failures indicate an IP routing or connectivity fault reachable from that Ubiquoss device. Objects under ubiIpMIBObjects would separately be polled to confirm the device's IP address and forwarding-table configuration matches intended provisioning.

What Can Be Monitored

IP address/forwarding configuration
SNMP-triggered ping test execution
ping reachability results
IP routing table entries

Imported Objects

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From UBQS-SMI

ubiMgmtv2

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
ubiIpMIB	1.3.6.1.4.1.7800.100.14			This MIB module defines IP information.
ubiIpMIBNotificationPrefix	1.3.6.1.4.1.7800.100.14.0
ubiIpMIBNotifications	1.3.6.1.4.1.7800.100.14.0.1
ubiPingMIBNotifications	1.3.6.1.4.1.7800.100.14.0.2
NTF ubiPingSendCompletion	1.3.6.1.4.1.7800.100.14.0.2.1			This notification is sent at the completion of the sequence of pings.
ubiIpMIBObjects	1.3.6.1.4.1.7800.100.14.1
ubiIpAddrTable	1.3.6.1.4.1.7800.100.14.1.1		not-accessible	The table of addressing information relevant to this entity's IP addresses.
ubiIpAddrEntry	1.3.6.1.4.1.7800.100.14.1.1.1		not-accessible	The addressing information for one of this entity's IP addresses.
IPt ubiIpAddrType	1.3.6.1.4.1.7800.100.14.1.1.1.1	InetAddressType	read-only	The IP address type. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention.
IP ubiIpAddress	1.3.6.1.4.1.7800.100.14.1.1.1.2	InetAddress	read-only	The IP address to which this entry's addressing information pertains.
ADR ubiIpAddrPrefixLen	1.3.6.1.4.1.7800.100.14.1.1.1.3	InetAddressPrefixLength	read-only	The prefix length associated with the IP address.
NUM ubiIpAddrIfIndex	1.3.6.1.4.1.7800.100.14.1.1.1.4	InterfaceIndex	read-create	The index value which uniquely identifies the interface to which this entry is applicable.
INT ubiIpAddrStatus	1.3.6.1.4.1.7800.100.14.1.1.1.5	INTEGER	read-create	Indicate whether this entry is primary or not.
ROW ubiIpAddrRowstatus	1.3.6.1.4.1.7800.100.14.1.1.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
ubiInetRouteTable	1.3.6.1.4.1.7800.100.14.1.2		not-accessible	The table of addressing information relevant to this entity's IP addresses.
ubiInetRouteEntry	1.3.6.1.4.1.7800.100.14.1.2.1		not-accessible	The addressing information for one of this entity's IP addresses.
U32 ubiInetRouteInstance	1.3.6.1.4.1.7800.100.14.1.2.1.1	Unsigned32	read-only	The instance identifier of the (conceptual) routing table containing this route.
IPt ubiInetRouteDestType	1.3.6.1.4.1.7800.100.14.1.2.1.2	InetAddressType	read-only	The destination address type. ipv4(1) An IPv4 address as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 address as defined by the InetAddressIPv6 textual convention.
IP ubiInetRouteDest	1.3.6.1.4.1.7800.100.14.1.2.1.3	InetAddress	read-only	The destination IP address of this route.
ADR ubiInetRouteDestPfxLen	1.3.6.1.4.1.7800.100.14.1.2.1.4	InetAddressPrefixLength	read-only
IPt ubiInetRouteNextHopType	1.3.6.1.4.1.7800.100.14.1.2.1.5	InetAddressType	read-only
IP ubiInetRouteNextHop	1.3.6.1.4.1.7800.100.14.1.2.1.6	InetAddress	read-only
NUM ubiInetRouteIfIndex	1.3.6.1.4.1.7800.100.14.1.2.1.7	InterfaceIndex	read-only
INT ubiInetRoutetype	1.3.6.1.4.1.7800.100.14.1.2.1.8	INTEGER	read-only
INT ubiInetRouteProto	1.3.6.1.4.1.7800.100.14.1.2.1.9	INTEGER	read-only
I32 ubiInetRouteMetric1	1.3.6.1.4.1.7800.100.14.1.2.1.10	Integer32	read-only
I32 ubiInetRouteMetric2	1.3.6.1.4.1.7800.100.14.1.2.1.11	Integer32	read-only
I32 ubiInetRouteMetric3	1.3.6.1.4.1.7800.100.14.1.2.1.12	Integer32	read-only
I32 ubiInetRouteMetric4	1.3.6.1.4.1.7800.100.14.1.2.1.13	Integer32	read-only
I32 ubiInetRouteMetric5	1.3.6.1.4.1.7800.100.14.1.2.1.14	Integer32	read-only
INT ubiInetRouteStatus	1.3.6.1.4.1.7800.100.14.1.2.1.15	INTEGER	read-only
I32 ubiInetRouteDistance	1.3.6.1.4.1.7800.100.14.1.2.1.16	Integer32	read-write
U32 ubiInetRouteTag	1.3.6.1.4.1.7800.100.14.1.2.1.17	Unsigned32	read-write
STR ubiInetRouteNextHopName	1.3.6.1.4.1.7800.100.14.1.2.1.18	DisplayString	read-write
ROW ubiInetRouteRowstatus	1.3.6.1.4.1.7800.100.14.1.2.1.19	RowStatus	read-create
ubiIpv6NeighborTable	1.3.6.1.4.1.7800.100.14.1.3		not-accessible	The table of addressing information relevant to this entity's IPv6 addresses.
ubiIpv6NeighborEntry	1.3.6.1.4.1.7800.100.14.1.3.1		not-accessible	The addressing information for one of this entity's IPv6 addresses.
NUM ubiIpv6NeighborIfIndex	1.3.6.1.4.1.7800.100.14.1.3.1.1	InterfaceIndex	read-only	The inde value which uniquely identifies the interface to which this entry is applicable
PHY ubiIpv6NeighborPhysAddress	1.3.6.1.4.1.7800.100.14.1.3.1.2	PhysAddress	read-create	The media-dependent `physical' address. This object should return 0 when this entry is in the 'incomplete' state. As the entries in this table are typically not persistent when this object is written the entity should not save the change to non-volatile storage. Note: a stronger requirement is not used because this object was previously defined.
IP ubiIpv6NeighborNetAddress	1.3.6.1.4.1.7800.100.14.1.3.1.3	InetAddress	read-only	The Ipv6Address corresponding to the media-dependent `physical' address. This object predates the rule limiting index objects to a max access value of 'not-accessible' and so continues to use a value of 'read-create'.
INT ubiIpv6NeighborType	1.3.6.1.4.1.7800.100.14.1.3.1.4	INTEGER	read-only	The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ubiIpv6NeighborTable. That is, it effectively dis-associates the interface identified with said entry from the mapping identified with said entry. It is an implementation- specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ubiIpv6NeighborType object. As the entries in this table are typically not persistent when this object is written the entity should not save the change to non-volatile storage. Note: a stronger requirement is not used because this object was previously defined.
INT ubiIpv6NeighborState	1.3.6.1.4.1.7800.100.14.1.3.1.5	INTEGER	read-only	The Neighbor Unreachability Detection [3] state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in use, this object is always unknown(6).
TIM ubiIpv6NeighborLastUpdated	1.3.6.1.4.1.7800.100.14.1.3.1.6	TimeStamp	read-only	The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
ROW ubiIpv6NeighborRowstatus	1.3.6.1.4.1.7800.100.14.1.3.1.7	RowStatus	read-create	The status of this conceptual row. As all objects in this conceptual row have default values, a row can be created and made active by setting this object appropriately. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified.
ubiPingMIBObjects	1.3.6.1.4.1.7800.100.14.2
ubiPingGlobal	1.3.6.1.4.1.7800.100.14.2.1
ubiPingSend	1.3.6.1.4.1.7800.100.14.2.2
INT ubiPingSendProto	1.3.6.1.4.1.7800.100.14.2.2.1	INTEGER	read-write	The protocol to use.
STR ubiPingSendTarget	1.3.6.1.4.1.7800.100.14.2.2.2	DisplayString	read-write	The address of the device to be pinged.
I32 ubiPingSendRepeat	1.3.6.1.4.1.7800.100.14.2.2.3	Integer32	read-write	Specifies the number of ping packets to send to the target.
I32 ubiPingSendPacketSize	1.3.6.1.4.1.7800.100.14.2.2.4	Integer32	read-write	Specifies the size of ping packets to send to the target.
I32 ubiPingSendTimeout	1.3.6.1.4.1.7800.100.14.2.2.5	Integer32	read-write	Specifies the amount of time to wait for a response.
I32 ubiPingSendInterval	1.3.6.1.4.1.7800.100.14.2.2.6	Integer32	read-write	Specifies the amount of time to wait before sending the next packet.
STR ubiPingSendSrcAddr	1.3.6.1.4.1.7800.100.14.2.2.7	DisplayString	read-write	Specifies the sender IP address for sending packets.
I32 ubiPingSendTTL	1.3.6.1.4.1.7800.100.14.2.2.8	Integer32	read-write	Specifies the TTL.
I32 ubiPingSendTos	1.3.6.1.4.1.7800.100.14.2.2.9	Integer32	read-write	Specifies the Type Of Service.
INT ubiPingSendDF	1.3.6.1.4.1.7800.100.14.2.2.10	INTEGER	read-write	Specifies the DF bit in IP header. dont(2) means a packet cannot be fragmented.
INT ubiPingSendExecute	1.3.6.1.4.1.7800.100.14.2.2.15	INTEGER	read-write	Send the ping packets when value is set to send(1).
ubiPingResults	1.3.6.1.4.1.7800.100.14.2.3
T/F ubiPingSendCompleted	1.3.6.1.4.1.7800.100.14.2.3.1	TruthValue	accessible-for-notify	Set to true when all the packets in this sequence have been either responded to or timed out.
C32 ubiPingSendPackets	1.3.6.1.4.1.7800.100.14.2.3.2	Counter32	accessible-for-notify	The total number of the sending ping.
C32 ubiPingReceivedPackets	1.3.6.1.4.1.7800.100.14.2.3.3	Counter32	accessible-for-notify	The total number of the received ping.
ubiIpMIBConformance	1.3.6.1.4.1.7800.100.14.3
ubiIpMIBCompliances	1.3.6.1.4.1.7800.100.14.3.1
ubiIpMIBCompliance	1.3.6.1.4.1.7800.100.14.3.1.2			The compliance statement for entities which implement the UBQS-IP-MIB
ubiIpMIBGroups	1.3.6.1.4.1.7800.100.14.3.2
ubiIpAddrGroup	1.3.6.1.4.1.7800.100.14.3.2.1			A collection of objects containing information about the address information of system.
ubiPingGroup	1.3.6.1.4.1.7800.100.14.3.2.2			A collection of objects containing information about the ping.

RFC description

IP configuration and ping utility management for Ubiquoss network switches.

Start monitoring Ubiquoss switches/access routers (IP address/route config and SNMP-ping reachability status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UBQS-IP-MIB

What Is UBQS-IP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description