UBQS-CFM-MIB

All MIBs › UBQS-CFM-MIB

Organization: Ubiquoss Corp.

Last Updated: 2010-11-25

Description: IEEE 802.1ag Connectivity Fault Management (CFM) for Ubiquoss Ethernet switches, managing maintenance domains, MEPs, and OAM continuity checks

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is UBQS-CFM-MIB?

UBQS-CFM-MIB is a vendor-specific module from Ubiquoss, an Ethernet switch and access equipment vendor, implementing IEEE 802.1ag Connectivity Fault Management (CFM) for detecting and isolating faults in Ethernet networks. It exposes configuration and status data for CFM maintenance domains, maintenance associations, Maintenance End Points (MEPs), and Remote MEPs (RMEPs), along with continuity-check OAM state. Its primary use is monitoring software/protocol-level fault status rather than physical hardware: it lets an administrator track whether continuity checks between MEPs are succeeding, detect a remote MEP that has stopped responding (indicating a link or path fault), and verify maintenance domain/association configuration consistency across the network. It is explicitly built on the IEEE 802.1ag Connectivity Fault Management standard, so it depends conceptually on that standard's data model even though it is a proprietary implementation. It is typically deployed on Ubiquoss Ethernet access/aggregation switches in carrier Ethernet or metro Ethernet networks where end-to-end fault detection across multiple domains is required. Engineers can download the UBQS-CFM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UBQS-CFM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ubiquoss Ethernet access/aggregation switch

Monitoring Examples

An operator would poll ubiCfmMd and ubiCfmMa to enumerate configured maintenance domains and associations, then check ubiCfmRmep entries for each remote MEP to confirm continuity-check messages are being received without loss. A remote MEP entry transitioning to a fault or timeout state would indicate a break in the Ethernet path between the local and remote maintenance points, triggering an alarm via ubiCFMMIBNotificationPrefix-rooted traps. This gives fine-grained, standards-based fault isolation across a multi-domain Ethernet service.

What Can Be Monitored

maintenance domain configuration
maintenance association configuration
MEP and remote MEP status
continuity-check fault/timeout state
CFM fault notifications/traps

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

From UBQS-LAG-MIB

ubiAggId

OBJECT-TYPE

From UBQS-SMI

ubiMgmtv2

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using ubiCfmMepOamSendLoopbackFrameCount OID:

Select an Ubiquoss Ethernet switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ubiCfmMepOamSendLoopbackFrameCount into the Find box to locate it in the OID tree, then select it and click OK. It reports the counter to transmit CFM loopback frame. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ubiCFMMIB	1.3.6.1.4.1.7800.100.10			Connectivity Fault Management module for managing IEEE 802.1ag
ubiCFMMIBNotificationPrefix	1.3.6.1.4.1.7800.100.10.0
ubiCfmNotifications	1.3.6.1.4.1.7800.100.10.0.0
NTF ubiCfmRemoteMepStatusChange	1.3.6.1.4.1.7800.100.10.0.0.1			Remote MEP state(CC state) change Notification
NTF ubiCfmAggPortRemoteMepStatusChange	1.3.6.1.4.1.7800.100.10.0.0.2			Notification that Remote MEP state(CC state) on port-gruop change
NTF ubiCfmPmFrameDelayEvent	1.3.6.1.4.1.7800.100.10.0.0.3			To generate notification when ubiCfmMepPmCurrentValue is bigger than ubiCfmMaPmDelayThreshold
NTF ubiCfmPmFrameLossEvent	1.3.6.1.4.1.7800.100.10.0.0.4			To generate notification when ubiCfmMepPmCurrentValue is bigger than ubiCfmMaPmLossThreshold
NTF ubiCfmMepEtherPingSendResult	1.3.6.1.4.1.7800.100.10.0.0.5			Indicates the result of the operation: - ok The Loopback Message(s)reply received - fail The Loopback Message(s)reply don't recieved - already active Another LBM is being transmitted - Not ready Do not initator state machine for LBM sending
NTF ubiCfmMepLinkTraceSendResult	1.3.6.1.4.1.7800.100.10.0.0.6			A LTR information about LTMs transmitted
NTF ubiCfmCCConfigDefectAlarm	1.3.6.1.4.1.7800.100.10.0.0.7			The CCM defect about Config error
ubiCFMMIBObjects	1.3.6.1.4.1.7800.100.10.1
ubiCfmMd	1.3.6.1.4.1.7800.100.10.1.1
ubiCfmMdTable	1.3.6.1.4.1.7800.100.10.1.1.1		not-accessible	The Maintenance Domain table. Each row in the table represents a different Maintenance Domain. A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance
ubiCfmMdEntry	1.3.6.1.4.1.7800.100.10.1.1.1.1		not-accessible	The Maintenance Domain table entry. INDEX { ubiBridgeId, ubiCfmMdIndex }
U32 ubiCfmMdIndex	1.3.6.1.4.1.7800.100.10.1.1.1.1.1	Unsigned32	not-accessible	The index to the Maintenance Domain table.
NUM ubiCfmMdName	1.3.6.1.4.1.7800.100.10.1.1.1.1.2	Dot1agCfmMaintDomainName	read-create	The Maintenance Domain name. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
NUM ubiCfmMdNameType	1.3.6.1.4.1.7800.100.10.1.1.1.1.3	Dot1agCfmMaintDomainNameType2	read-create	The type (and thereby format) of the Maintenance Domain Name. There are two types. IEEE802.1ag type(string, address...etc) and ITU-T Y.1731 type (itu-t)
DOT ubiCfmMdLevel	1.3.6.1.4.1.7800.100.10.1.1.1.1.4	Dot1agCfmMDLevel	read-create	The Maintenance Domain Level. (0 ~ 7 level)
DOT ubiCfmMdMipCreation	1.3.6.1.4.1.7800.100.10.1.1.1.1.5	Dot1agCfmMhfCreation	read-create	Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is not allowed.
ROW ubiCfmMdRowStatus	1.3.6.1.4.1.7800.100.10.1.1.1.1.6	RowStatus	read-create	The status of the row.
ubiCfmDefaultMdTable	1.3.6.1.4.1.7800.100.10.1.1.2		not-accessible	For each bridge component, the Default MD Level Managed Object controls MHF creation for VIDs that are not attached to a specific Maintenance Association Managed Object, and Sender ID TLV transmission by those MHFs. For each Bridge Port, and for each VLAN ID whose data can pass through that Bridge Port, an entry in this table is used by the algorithm in subclause 22.2.3 only if there is no entry in the Maintenance Association table defining an MA for the same VLAN ID and MD Level as this table's entry, and on which MA an Up MEP is defined. If there exists such an MA, that MA's objects are used by the algorithm in subclause 22.2.3 in place of this table entry's objects. The agent maintains the value of ubiCfmDefaultMdRowStatus to indicate whether this entry is overridden by an MA. When first initialized, the agent creates this table automatically with entries for all VLAN IDs, with the default values specified for each object.
ubiCfmDefaultMdEntry	1.3.6.1.4.1.7800.100.10.1.1.2.1		not-accessible	The Default MD Level table entry.
VLA ubiCfmDefaultMdVlanId	1.3.6.1.4.1.7800.100.10.1.1.2.1.1	VlanIndex	not-accessible	The Primary VID of the VLAN to which this entry's objects apply.
DOT ubiCfmDefaultMdLevel	1.3.6.1.4.1.7800.100.10.1.1.2.1.2	Dot1agCfmMDLevel	read-create	A value indicating the MD Level at which MHFs are to be created, and Sender ID TLV transmission by those MHFs is to be controlled, for the VLAN to which this entry's objects apply. If this object has the value -1, the MD Level for MHF creation for this VLAN is controlled by ubiCfmDefaultMdLevel.
DOT ubiCfmDefaultMdMipCreation	1.3.6.1.4.1.7800.100.10.1.1.2.1.3	Dot1agCfmMhfCreation	read-create	A value indicating if the Management entity can create MHFs (MIP Half Function) for this VID at this MD Level. If this object has the value defMHFdefer, MHF creation for this VLAN is controlled by dot1agCfmDefaultMdDefMhfCreation. The value of this variable is meaningless if the values of ubiCfmDefaultMdMipCreation is false.
ROW ubiCfmDefaultMdRowStatus	1.3.6.1.4.1.7800.100.10.1.1.2.1.4	RowStatus	read-create	The status of the row.
ubiCfmMa	1.3.6.1.4.1.7800.100.10.1.2
ubiCfmMaTable	1.3.6.1.4.1.7800.100.10.1.2.1		not-accessible	The Maintenance Association table. Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance.
ubiCfmMaEntry	1.3.6.1.4.1.7800.100.10.1.2.1.1		not-accessible	The MA table entry.
U32 ubiCfmMaIndex	1.3.6.1.4.1.7800.100.10.1.2.1.1.1	Unsigned32	not-accessible	The index to the Maintenance Association table.
NUM ubiCfmMaName	1.3.6.1.4.1.7800.100.10.1.2.1.1.2	Dot1agCfmMaintAssocName	read-create	The Short Maintenance Association name. This name MUST be unique within a maintenance domain.
NUM ubiCfmMaNameType	1.3.6.1.4.1.7800.100.10.1.2.1.1.3	Dot1agCfmMaintAssocNameType	read-create	The type (and thereby format) of the Maintenance Association Name.
VLA ubiCfmMaVlanId	1.3.6.1.4.1.7800.100.10.1.2.1.1.4	VlanIndex	read-create	The Primary VLAN ID with which the Maintenance Association is associated, or 0 if the MA is not attached to any VID.
DOT ubiCfmMaMipCreation	1.3.6.1.4.1.7800.100.10.1.2.1.1.5	Dot1agCfmMhfCreation	read-create	Indicates if the Management entity can create MHFs (MIP Half Function) for this MA.
ROW ubiCfmMaRowStatus	1.3.6.1.4.1.7800.100.10.1.2.1.1.6	RowStatus	read-create	The status of the row.
ubiCfmMaAttrTable	1.3.6.1.4.1.7800.100.10.1.2.2		not-accessible	An Attribute table for each MA(Maintenance Association). Such as, CCM transmission interval.
ubiCfmMaAttrEntry	1.3.6.1.4.1.7800.100.10.1.2.2.1		not-accessible	An attribute entry
I32 ubiCfmMaAttrCCInterval	1.3.6.1.4.1.7800.100.10.1.2.2.1.1	Integer32	read-write	Interval between CCM transmissions to be used by all MEPs in the MA. interval3ms(1) CCMs are sent every 3 1/3 milliseconds. interval10ms(2) CCMs are sent every 10 milliseconds. interval100ms(3) CCMs are sent every 100 milliseconds. interval1s(4) CCMs are sent every 1 second. interval10s(5) CCMs are sent every 10 seconds. interval1min(6) CCMs are sent every minute. interval10min(7) CCMs are sent every 10 minutes.
ubiCfmMaPmTable	1.3.6.1.4.1.7800.100.10.1.2.3		not-accessible	An attribute for Performance Monitoring
ubiCfmMaPmEntry	1.3.6.1.4.1.7800.100.10.1.2.3.1		not-accessible	Performance Monitoring Entry
I32 ubiCfmMaPmDelayInterval	1.3.6.1.4.1.7800.100.10.1.2.3.1.1	Integer32	read-write	Interval to trasmit DM(delay measurement)message
I32 ubiCfmMaPmLossInterval	1.3.6.1.4.1.7800.100.10.1.2.3.1.2	Integer32	read-write	Interval to trasmit LM(loss measurement)message
I32 ubiCfmMaPmDelayThreshold	1.3.6.1.4.1.7800.100.10.1.2.3.1.3	Integer32	read-write	Treshold to limit for delay
I32 ubiCfmMaPmLossThreshold	1.3.6.1.4.1.7800.100.10.1.2.3.1.4	Integer32	read-write	Treshold to limit for loss
ubiCfmRmep	1.3.6.1.4.1.7800.100.10.1.3
ubiCfmRmepTable	1.3.6.1.4.1.7800.100.10.1.3.1		not-accessible	Information of Remote Mep table
ubiCfmRmepEntry	1.3.6.1.4.1.7800.100.10.1.3.1.1		not-accessible	Information of Remote Mep entry
DOT ubiCfmRmepId	1.3.6.1.4.1.7800.100.10.1.3.1.1.1	Dot1agCfmMepId	not-accessible	Maintenance association End Point Identifier of a remote MEP
VLA ubiCfmRmepVlanId	1.3.6.1.4.1.7800.100.10.1.3.1.1.2	VlanIndex	read-write	VLAN Identifier of a remote MEP. Same value of local MEP(MA's VID)
MAC ubiCfmRmepRemoteMacAddr	1.3.6.1.4.1.7800.100.10.1.3.1.1.3	MacAddress	read-write	The MAC address of the remote MEP.
INT ubiCfmRmepCrossCheckType	1.3.6.1.4.1.7800.100.10.1.3.1.1.4	INTEGER	read-write	CrossCheck Type (uicast or multicast).
INT ubiCfmRmepStatus	1.3.6.1.4.1.7800.100.10.1.3.1.1.5	INTEGER	read-only	Continuity Status to local MEP from remote MEP. Remote MEP state machine last entered either the RMEP_FAILED or RMEP_OK state
ROW ubiCfmRmepRowStatus	1.3.6.1.4.1.7800.100.10.1.3.1.1.6	RowStatus	read-create	The status of the row.
ubiCfmMep	1.3.6.1.4.1.7800.100.10.1.4
ubiCfmMepTable	1.3.6.1.4.1.7800.100.10.1.4.1		not-accessible	The Maintenance Association End Point (MEP) table.
ubiCfmMepEntry	1.3.6.1.4.1.7800.100.10.1.4.1.1		not-accessible	The known MEPS table entry.
DOT ubiCfmMepId	1.3.6.1.4.1.7800.100.10.1.4.1.1.1	Dot1agCfmMepId	not-accessible	Integer that is unique among all the MEPs in the same MA. Other definition is: A small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID.
DOT ubiCfmMepMdLevel	1.3.6.1.4.1.7800.100.10.1.4.1.1.2	Dot1agCfmMDLevel	read-write	MD level that belong to this MD
VLA ubiCfmMepVlanId	1.3.6.1.4.1.7800.100.10.1.4.1.1.3	VlanIndex	read-write	An integer indicating the Primary VID of the MEP, always one of the VIDs assigned to the MEP's MA. The value 0 indicates that either the Primary VID is that of the MEP's MA, or that the MEP's MA is associated with no VID.
T/F ubiCfmMepActive	1.3.6.1.4.1.7800.100.10.1.4.1.1.4	TruthValue	read-write	Administrative state of the MEP. A Boolean indicating the administrative state of the MEP. True indicates that the MEP is to function normally, and false that it is to cease functioning.
INT ubiCfmMepDirection	1.3.6.1.4.1.7800.100.10.1.4.1.1.5	INTEGER	read-write	The direction in which the MEP faces on the Bridge port.
NUM ubiCfmMepMdName	1.3.6.1.4.1.7800.100.10.1.4.1.1.6	Dot1agCfmMaintDomainName	read-write	MD name that belong to this MD
INT ubiCfmMepUniMep	1.3.6.1.4.1.7800.100.10.1.4.1.1.7	INTEGER	read-write	The flag to configure UNI-MEP
DOT ubiCfmMepRmepId	1.3.6.1.4.1.7800.100.10.1.4.1.1.8	Dot1agCfmMepId	read-write	The specified RmepID that is RMEP configured
STR ubiCfmMepIfname	1.3.6.1.4.1.7800.100.10.1.4.1.1.9	DisplayString	read-only	This object is the IfIndex of the interface where MEP configure.
MAC ubiCfmMepIfMacAddr	1.3.6.1.4.1.7800.100.10.1.4.1.1.10	MacAddress	read-only	Thsi object is the MAC address of the interface where MEP configure.
T/F ubiCfmMepRdi	1.3.6.1.4.1.7800.100.10.1.4.1.1.11	TruthValue	read-only	State of the RDI bit in the sending CCM (true for RDI=1), or false.
INT ubiCfmMepCCType	1.3.6.1.4.1.7800.100.10.1.4.1.1.12	INTEGER	read-write	The type of CCM message.
INT ubiCfmMepCCEnable	1.3.6.1.4.1.7800.100.10.1.4.1.1.13	INTEGER	read-write	If set to true, the MEP will generate CCM messages.
ROW ubiCfmMepRowStatus	1.3.6.1.4.1.7800.100.10.1.4.1.1.14	RowStatus	read-create	The status of the row.
I32 ubiCfmMepMissingTime	1.3.6.1.4.1.7800.100.10.1.4.1.1.15	Integer32	read-only	The pass time after received last CCM
I32 ubiCfmMepExpiredTime	1.3.6.1.4.1.7800.100.10.1.4.1.1.16	Integer32	read-only	The remain time till Expired RMEP status
INT ubiCfmMepForceEgressTag	1.3.6.1.4.1.7800.100.10.1.4.1.1.17	INTEGER	read-write	UNI-MEP send CCM with VID information(tagged) or send CCM without VID information (untagged). If set none-value, tag information is depend on egress interface policy
ubiCfmMepPmDelayTable	1.3.6.1.4.1.7800.100.10.1.4.2		not-accessible	Performance Monitoring Table
ubiCfmMepPmDelayEntry	1.3.6.1.4.1.7800.100.10.1.4.2.1		not-accessible	Performance Monitoring Entry
INT ubiCfmMepPmDelayRmep	1.3.6.1.4.1.7800.100.10.1.4.2.1.1	INTEGER	read-create	Remote MEP ID to measure performance
INT ubiCfmMepPmDelayFrameType	1.3.6.1.4.1.7800.100.10.1.4.2.1.2	INTEGER	read-create	The type of frame that is to measure
U32 ubiCfmMepPmDelayCurrentValue	1.3.6.1.4.1.7800.100.10.1.4.2.1.3	Unsigned32	read-only	Result value of measurement
INT ubiCfmMepPmDelayTxInterval	1.3.6.1.4.1.7800.100.10.1.4.2.1.4	INTEGER	read-create	Period that operate performance monitoring
INT ubiCfmMepPmDelayState	1.3.6.1.4.1.7800.100.10.1.4.2.1.5	INTEGER	read-only	Result state of measurement. If ubiCfmMepPmCurrentValue is lower than threshold, ubiCfmMepPmState is OK. If ubiCfmMepPmCurrentValue is over the configured threshold, ubiCfmMepPmState is FAIL.
ROW ubiCfmMepPmDelayRowStatus	1.3.6.1.4.1.7800.100.10.1.4.2.1.6	RowStatus	read-create	The status of the row.
I32 ubiCfmMepPmDelayMin	1.3.6.1.4.1.7800.100.10.1.4.2.1.7	Integer32	read-only	Minimum delay measured by performance monitoring
I32 ubiCfmMepPmDelayMax	1.3.6.1.4.1.7800.100.10.1.4.2.1.8	Integer32	read-only	Maximum delay measured by performance monitoring
I32 ubiCfmMepPmDelayAvg	1.3.6.1.4.1.7800.100.10.1.4.2.1.9	Integer32	read-only	Average of delay measured by performance monitoring
ubiCfmMepPmLossTable	1.3.6.1.4.1.7800.100.10.1.4.3		not-accessible	Performance Monitoring Table
ubiCfmMepPmLossEntry	1.3.6.1.4.1.7800.100.10.1.4.3.1		not-accessible	Performance Monitoring Entry
INT ubiCfmMepPmLossRmep	1.3.6.1.4.1.7800.100.10.1.4.3.1.1	INTEGER	read-create	Remote MEP ID to measure performance
INT ubiCfmMepPmLossFrameType	1.3.6.1.4.1.7800.100.10.1.4.3.1.2	INTEGER	read-create	The type of frame that is to measure
U32 ubiCfmMepPmLossCurrentValue	1.3.6.1.4.1.7800.100.10.1.4.3.1.3	Unsigned32	read-only	Result value of measurement
INT ubiCfmMepPmLossTxInterval	1.3.6.1.4.1.7800.100.10.1.4.3.1.4	INTEGER	read-create	Period that operate performance monitoring
INT ubiCfmMepPmLossState	1.3.6.1.4.1.7800.100.10.1.4.3.1.5	INTEGER	read-only	Result state of measurement. If ubiCfmMepPmCurrentValue is lower than threshold, ubiCfmMepPmState is OK. If ubiCfmMepPmCurrentValue is over the configured threshold, ubiCfmMepPmState is FAIL.
ROW ubiCfmMepPmLossRowStatus	1.3.6.1.4.1.7800.100.10.1.4.3.1.6	RowStatus	read-create	The status of the row.
I32 uniCfmMepPmLossNearEndTot	1.3.6.1.4.1.7800.100.10.1.4.3.1.7	Integer32	read-only	Frame loss of near end measured by performance monitoring
I32 uniCfmMepPmLossFarEndTot	1.3.6.1.4.1.7800.100.10.1.4.3.1.8	Integer32	read-only	Frame loss of far end measured by performance monitoring
I32 ubiCfmMepPmLossRttMin	1.3.6.1.4.1.7800.100.10.1.4.3.1.9	Integer32	read-only	Minimum route-trip time between MEPs
I32 ubiCfmMepPmLossRttMax	1.3.6.1.4.1.7800.100.10.1.4.3.1.10	Integer32	read-only	Maximum route-trip time between MEPs
I32 ubiCfmMepPmLossRttAvg	1.3.6.1.4.1.7800.100.10.1.4.3.1.11	Integer32	read-only	Average of route-trip time between MEPs
ubiCfmMepOamSend	1.3.6.1.4.1.7800.100.10.1.4.4
I32 ubiCfmMepOamSendBridgeId	1.3.6.1.4.1.7800.100.10.1.4.4.1	Integer32	read-write	Bridge ID to send Ping or Linktrace
U32 ubiCfmMepOamSendMdIndex	1.3.6.1.4.1.7800.100.10.1.4.4.2	Unsigned32	read-write	Maintenance Domain ID to send Ping or Linktrace
U32 ubiCfmMepOamSendMaIndex	1.3.6.1.4.1.7800.100.10.1.4.4.3	Unsigned32	read-write	Maintenance Association ID to send Ping or Linktrace
U32 ubiCfmMepOamSendMepId	1.3.6.1.4.1.7800.100.10.1.4.4.4	Unsigned32	read-write	MEP ID to send Ping or Linktrace
MAC ubiCfmMepOamSendDstMac	1.3.6.1.4.1.7800.100.10.1.4.4.5	MacAddress	read-write	Destination MAC address
INT ubiCfmMepOamSendLoopbackFrameType	1.3.6.1.4.1.7800.100.10.1.4.4.6	INTEGER	read-write	Type of CFM loopback Frame (ETH-LB)
C32 ubiCfmMepOamSendLoopbackFrameCountEx	1.3.6.1.4.1.7800.100.10.1.4.4.7	Counter32	read-write	Counter to transmit CFM loopback frame
INT ubiCfmMepOamSendExecute	1.3.6.1.4.1.7800.100.10.1.4.4.8	INTEGER	read-write	Send ping/linktrace messages
ubiCfmMepOamResult	1.3.6.1.4.1.7800.100.10.1.4.5
INT ubiCfmMepOamResultEtherPing	1.3.6.1.4.1.7800.100.10.1.4.5.1	INTEGER	accessible-for-notify	The result of Loopback message sent. If already Loopback function activate, send trap result value on already-activated. if CC not connected or unicast RMEP crosscheck type, send trap result value on not-ready.
C32 ubiCfmMepOamResultEtherPingSndCount	1.3.6.1.4.1.7800.100.10.1.4.5.2	Counter32	accessible-for-notify	Counter of CFM loopback frame to send
C32 ubiCfmMepOamResultEtherPingRcvCount	1.3.6.1.4.1.7800.100.10.1.4.5.3	Counter32	accessible-for-notify	Received counter of CFM lopback reply
I32 ubiCfmMepOamResultEtherPingRttMin	1.3.6.1.4.1.7800.100.10.1.4.5.4	Integer32	accessible-for-notify	Minimum round-trip time measured by CFM loopback frame
I32 ubiCfmMepOamResultEtherPingRttMax	1.3.6.1.4.1.7800.100.10.1.4.5.5	Integer32	accessible-for-notify	Maximum round-trip time measured by CFM loopback frame
I32 ubiCfmMepOamResultEtherPingRttAvg	1.3.6.1.4.1.7800.100.10.1.4.5.6	Integer32	accessible-for-notify	Average of round-trip time measured by CFM loopback frame
MAC ubiCfmMepOamResultLinkTraceSrcMacAddr	1.3.6.1.4.1.7800.100.10.1.4.5.7	MacAddress	accessible-for-notify	MAC address returned in the ingress MAC address field.
I32 ubiCfmMepOamResultLinkTraceRcvIfIndex	1.3.6.1.4.1.7800.100.10.1.4.5.8	Integer32	accessible-for-notify	The index of local interface of received LTR
INT ubiCfmMepOamResultLinkTraceRelayAction	1.3.6.1.4.1.7800.100.10.1.4.5.9	INTEGER	accessible-for-notify	Indicates if a LTM was forwarded by the responding MP, as returned in the 'relay-hit' or 'relay-fdb' flag of the flags field. If other LT function already activate, on already-activated value. else if CC is not OK state, on not-ready value
I32 ubiCfmMepOamResultLinkTraceHopCount	1.3.6.1.4.1.7800.100.10.1.4.5.10	Integer32	accessible-for-notify	hop count for a returned LTR.
ubiCfmCCConfigDefectTable	1.3.6.1.4.1.7800.100.10.1.4.6		not-accessible	The CCM config defect table
ubiCfmCCConfigDefectEntry	1.3.6.1.4.1.7800.100.10.1.4.6.1		not-accessible	The CCM config defect entry
INT ubiCfmMepCCConfigDefect	1.3.6.1.4.1.7800.100.10.1.4.6.1.1	INTEGER	read-only	Number of Defect 0: None 1: Unexpected MEP ID 2: Unexpected Tx interval 3: Already Existed MEP
INT ubiCfmMepCCConfigDefectState	1.3.6.1.4.1.7800.100.10.1.4.6.1.2	INTEGER	read-only	State of defect condition 0: DefectConditionExit 1: DefectConditionEntry
ubiCfmServerMep	1.3.6.1.4.1.7800.100.10.1.5
ubiCfmServerMepTable	1.3.6.1.4.1.7800.100.10.1.5.1		not-accessible	A Server MEP represents the compound function of the Server layer termination function and Server/ETH adaptation function which is used to notify the ETH layer MEPs upon failure detection by the Server layer termination function or Server/ETH adaptation function, where the Server layer termination function is expected to run OAM mechanisms specific to the Server layer. A Server MEP needs to support ETH-AIS function, as described in clause 7.4, where the Server/ETH adaptation function is required to issue frames with ETH-AIS information upon detection of defect at the Server layer by the Server layer termination and/or adaptation function. (ITU-T Y.1731 5.3.1)
ubiCfmServerMepEntry	1.3.6.1.4.1.7800.100.10.1.5.1.1		not-accessible	Server MEP entry
INT ubiCfmServerMepTxInterval	1.3.6.1.4.1.7800.100.10.1.5.1.1.1	INTEGER	read-write	Periodic Interval of AIS Transmission
DOT ubiCfmServerMepAisLevel	1.3.6.1.4.1.7800.100.10.1.5.1.1.2	Dot1agCfmMDLevel	read-write	Destinaction Maintenance Domain Level of AIS
ROW ubiCfmServerMepRowStatus	1.3.6.1.4.1.7800.100.10.1.5.1.1.3	RowStatus	read-create	The status of the row.
ubiCfmNotificationEnables	1.3.6.1.4.1.7800.100.10.1.6
T/F ubiCfmRemoteMepStateChangeEnabled	1.3.6.1.4.1.7800.100.10.1.6.1	TruthValue	read-write	Remote MEP state(CC state) change Notification
T/F ubiCfmPmEventEnabled	1.3.6.1.4.1.7800.100.10.1.6.2	TruthValue	read-write	ubiCfmMepPmState change Notification
T/F ubiCfmCCConfigDefectAlarmEnabled	1.3.6.1.4.1.7800.100.10.1.6.3	TruthValue	read-write	Detect CCM config Defect notification
ubiCfmTrack	1.3.6.1.4.1.7800.100.10.1.7
BIT ubiCfmTrackEnable	1.3.6.1.4.1.7800.100.10.1.7.1	Bits	read-write	Not use
ubiCfmTrackTargetTable	1.3.6.1.4.1.7800.100.10.1.7.2		not-accessible	Not use
ubiCfmTrackTargetEntry	1.3.6.1.4.1.7800.100.10.1.7.2.1		not-accessible	Not use
INT ubiCfmTrackTargetSet	1.3.6.1.4.1.7800.100.10.1.7.2.1.1	INTEGER	read-write	Not use
ubiCFMMIBConformance	1.3.6.1.4.1.7800.100.10.2
ubiCfmMIBCompliances	1.3.6.1.4.1.7800.100.10.2.1
ubiVlanMIBCompliance	1.3.6.1.4.1.7800.100.10.2.1.1			The compliance statement for VTP implementations.
ubiCfmMIBGroups	1.3.6.1.4.1.7800.100.10.2.2
ubiCfmMaGroup	1.3.6.1.4.1.7800.100.10.2.2.1			The collection of objects for management of Maintenance Associations.

RFC description

Vendor-private MIB for Ubiquiti QS (Quality of Service) Connectivity Fault Management (CFM); defines objects for ethernet OAM and link health monitoring.

Start monitoring Ubiquoss Ethernet switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UBQS-CFM-MIB