All MIBs › TIMETRA-MPLS-MIB
Organization: Alcatel-Lucent
Last Updated: 2011-02-01
Description: TIMETRA-MPLS-MIB module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-MPLS-MIB?
TIMETRA-MPLS-MIB is Alcatel-Lucent's (now Nokia's) proprietary MIB for provisioning and monitoring MPLS on its SROS-based service router (7x50/SR) product line, internally branded Timetra. It exposes a table of configured MPLS LSPs (label-switched paths), including admin/operational state, source and destination addresses, LSP type, and outgoing segment index, alongside notification objects for MPLS-related events. Monitoring here focuses on software/protocol status of the MPLS control plane: an operator checks LSP operational state against admin state to detect LSPs that have failed to come up or gone down, indicating an underlying transport or routing problem. It extends vendor-neutral MPLS-LSR-MIB/MPLS-TE-MIB style concepts with Alcatel-Lucent-specific object naming (vRtr* prefix) rather than reusing the IETF MIBs directly. Deployment context is service-provider MPLS core/edge networks built on Alcatel-Lucent/Nokia SR-series routers, where network engineers can download the TIMETRA-MPLS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-MPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alcatel-Lucent/Nokia SROS service router (7x50/SR series)
Monitoring Examples
An operator polls vRtrMplsLspTable, comparing vRtrMplsLspAdminState to vRtrMplsLspOperState for each vRtrMplsLspName, to detect an LSP that is administratively enabled but operationally down. vRtrMplsLspFromAddr and vRtrMplsLspToAddr identify the LSP's endpoints for troubleshooting, and vRtrMplsLspOutSegIndx links to the outgoing label segment, while vRtrMplsLspLastChange shows when the LSP's state last changed.
What Can Be Monitored
- LSP admin/operational state
- LSP source/destination address
- LSP type
- LSP last-change time
- outgoing segment index
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressIPv6 | |
| InetAddressType |
From MPLS-LSR-MIB
| MplsLSPID | |
| MplsLabel | |
| mplsInSegmentEntry | OBJECT-TYPE |
| mplsOutSegmentEntry | OBJECT-TYPE |
| mplsXCLspId | OBJECT-TYPE |
From MPLS-TE-MIB
| MplsTunnelIndex | |
| mplsTunnelARHopEntry | OBJECT-TYPE |
| mplsTunnelIndex | OBJECT-TYPE |
| mplsTunnelIngressLSRId | OBJECT-TYPE |
| mplsTunnelInstance | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowPointer | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TestAndIncr | |
| TimeInterval | |
| TimeStamp | |
| TruthValue |
From TIMETRA-GLOBAL-MIB
| timetraSRMIBModules | OBJECT-IDENTITY |
| tmnxSRConfs | OBJECT-IDENTITY |
| tmnxSRNotifyPrefix | OBJECT-IDENTITY |
| tmnxSRObjs | OBJECT-IDENTITY |
From TIMETRA-TC-MIB
| TLNamedItemOrEmpty | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TmnxActionType | |
| TmnxAdminState | |
| TmnxEnabledDisabled | |
| TmnxMplsTpGlobalID | |
| TmnxMplsTpNodeID | |
| TmnxOperState | |
| TmnxRsvpDSTEClassType | |
| TmnxVRtrMplsLspID |
From TIMETRA-VRTR-MIB
| vRtrID | OBJECT-TYPE |
| vRtrIfIndex | OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using vRtrMplsLspOctets OID:
Select an Alcatel-Lucent/Nokia SROS service router (7x50/SR series) (MPLS LSP admin/oper status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vRtrMplsLspOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of octets that have been forwarded over current LSP active path. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| timetraMplsMIBModule | 1.3.6.1.4.1.6527.1.1.3.6 | This document is the SNMP MIB module to manage and provision the MPLS extensions for the Alcatel-Lucent SROS device. Copyright 2003-2013 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxMplsAdminGroupGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.8 | The group of objects supporting management of extended MPLS administrative groups on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsCompliances | 1.3.6.1.4.1.6527.3.1.1.6.1 | |||
| tmnxMplsConformance | 1.3.6.1.4.1.6527.3.1.1.6 | |||
| tmnxMplsFSGroupGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.9 | The group of objects supporting management of extended MPLS fate sharing groups on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsGlobalR2r1Group | 1.3.6.1.4.1.6527.3.1.1.6.2.12 | The group of objects supporting general management of extended MPLS on Alcatel-Lucent SROS series systems 2.1 Release. | ||
| tmnxMplsGlobalV10v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.47 | The group of all global objects in MPLS supporting management of MPLS features on Alcatel-Lucent SROS series systems 10.0 release. | ||
| tmnxMplsGlobalV5v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.16 | The group of objects supporting general management of extended MPLS on Alcatel-Lucent SROS series systems 5.0 Release. | ||
| tmnxMplsGlobalV6v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.18 | The group of objects supporting general management of extended MPLS on Alcatel-Lucent SROS series systems 6.0 Release. | ||
| tmnxMplsGlobalV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.26 | The group of all global objects in MPLS supporting management of MPLS features on Alcatel-Lucent SROS series systems 7.0 release. | ||
| tmnxMplsGlobalV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.38 | The group of all global objects in MPLS supporting management of MPLS features on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsGlobalV9v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.41 | The group of all global objects in MPLS supporting management of MPLS features on Alcatel-Lucent SROS series systems 9.0 release. | ||
| tmnxMplsGroups | 1.3.6.1.4.1.6527.3.1.1.6.2 | |||
| tmnxMplsIfGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.5 | The group of objects supporting management of extended MPLS interfaces on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsIfV6v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.21 | The group of objects supporting management of Te metric feature on extended MPLS interfaces on 6.0 release Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLabelRangeGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.15 | The group of objects supporting management of extended MPLS label ranges on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspAutoBWV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.40 | The group of all objects supporting management of Auto-Bandwidth in MPLS on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsLspPathGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.3 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspPathV6v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.20 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspPathV6v1Group | 1.3.6.1.4.1.6527.3.1.1.6.2.23 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspPathV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.31 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspPathV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.35 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsLspPathV9v0R4Group | 1.3.6.1.4.1.6527.3.1.1.6.2.46 | The group of objects supporting management of extended MPLS LSP to path mapping on Alcatel-Lucent SROS series systems 9.0.R4 release. | ||
| tmnxMplsLspR2r1Group | 1.3.6.1.4.1.6527.3.1.1.6.2.13 | The group of objects supporting management of extended MPLS LSPs on Alcatel-Lucent SROS series systems 2.1 Release. | ||
| tmnxMplsLspStatsV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.33 | The group of objects supporting management of egress/ingress statistics on Alcatel-Lucent SROS series systems release 7.0. | ||
| tmnxMplsLspTemplateV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.39 | The group of objects supporting management of LSP Templates in MPLS on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsLspV5v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.17 | The group of objects supporting management of extended MPLS LSPs on Alcatel-Lucent SROS series systems 5.0 Release. | ||
| tmnxMplsLspV6v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.22 | The group of objects supporting management of Te metric feature extended MPLS LSPs on 6.0 release Alcatel-Lucent SROS series systems. | ||
| tmnxMplsLspV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.25 | The group of objects supporting management of extended LSP in MPLS on on Alcatel-Lucent SROS series systems 7.0 release. | ||
| tmnxMplsLspV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.34 | The group of objects supporting management of extended LSP in MPLS on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsLspV9v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.42 | The group of objects supporting management of extended LSP in MPLS on Alcatel-Lucent SROS series systems 9.0 release. | ||
| tmnxMplsLspV9v0R4Group | 1.3.6.1.4.1.6527.3.1.1.6.2.43 | The group of objects supporting management of extended LSP in MPLS on Alcatel-Lucent SROS series systems 9.0R4 release. | ||
| tmnxMplsNotificationObjects | 1.3.6.1.4.1.6527.3.1.2.6.16 | |||
| tmnxMplsNotificationR2r1Group | 1.3.6.1.4.1.6527.3.1.1.6.2.14 | The group of notifications supporting the extended MPLS feature on Alcatel-Lucent SROS series systems 2.1 Release. | ||
| tmnxMplsNotifications | 1.3.6.1.4.1.6527.3.1.3.6.0 | |||
| tmnxMplsNotificationV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.30 | The group of notifications supporting the extended MPLS feature on Alcatel-Lucent SROS series systems 7.0 Release. | ||
| tmnxMplsNotificationV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.37 | The group of notifications supporting the extended MPLS feature on Alcatel-Lucent SROS series systems 8.0 Release. | ||
| tmnxMplsNotifV9v0R4Group | 1.3.6.1.4.1.6527.3.1.1.6.2.45 | The group of notifications supporting the extended MPLS feature on Alcatel-Lucent SROS series systems 9.0.R4 Release. | ||
| tmnxMplsNotifyObjsGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.10 | The group of objects supporting extended MPLS notifications on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsNotifyObjsV10v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.48 | The group of notification objects supporting extended MPLS notifications on Alcatel-Lucent SROS series systems 10.0 release. | ||
| tmnxMplsNotifyObjsV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.29 | The group of notification objects supporting extended MPLS notifications on Alcatel-Lucent SROS series systems 7.0 release. | ||
| tmnxMplsNotifyObjsV8v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.36 | The group of notification objects supporting extended MPLS notifications on Alcatel-Lucent SROS series systems 8.0 release. | ||
| tmnxMplsNotifyObjsV9v0R4Group | 1.3.6.1.4.1.6527.3.1.1.6.2.44 | The group of notification objects supporting extended MPLS notifications on Alcatel-Lucent SROS series systems 9.0.R4 release. | ||
| tmnxMplsNotifyPrefix | 1.3.6.1.4.1.6527.3.1.3.6 | |||
| tmnxMplsNotifyV10v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.49 | The group of notifications supporting the extended MPLS feature on Alcatel-Lucent SROS series systems 10.0 Release. | ||
| tmnxMplsObjs | 1.3.6.1.4.1.6527.3.1.2.6 | |||
| tmnxMplsObsoleteGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.24 | The group of obsolete objects which are no longer supported in MPLS on 6.0R4 release onwards on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsP2mpInstanceGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.27 | The group of all P2MP instance related objects supporting management of P2MP feature in MPLS on Alcatel-Lucent SROS series systems 7.0 release. | ||
| tmnxMplsP2mpS2lGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.28 | The group of all S2L sub-LSP related objects supporting management of P2MP feature in MPLS on Alcatel-Lucent SROS series systems 7.0 release. | ||
| tmnxMplsSrlgV6v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.19 | The group of objects supporting management of SRLG on Alcatel 7xxx SR series systems release 6.0. | ||
| tmnxMplsSrlgV7v0Group | 1.3.6.1.4.1.6527.3.1.1.6.2.32 | The group of objects supporting management of SRLG on Alcatel-Lucent SROS series systems release 7.0. | ||
| tmnxMplsTpGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.50 | The group of objects supporting management of the MPLS-TP feature on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsTunnelARHopGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.6 | The group of objects supporting management of extended MPLS Tunnel AR hops on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsTunnelCHopGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.7 | The group of objects supporting management of extended MPLS CSPF Tunnel hops on Alcatel-Lucent SROS series systems. | ||
| tmnxMplsV10v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.10 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 10.0 Release. | ||
| tmnxMplsV3v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.3 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 3.0 Release. | ||
| tmnxMplsV5v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.4 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 5.0 Release. | ||
| tmnxMplsV6v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.5 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 6.0 Release. | ||
| tmnxMplsV6v1Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.6 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 6.1 Release. | ||
| tmnxMplsV7v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.7 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 6.1 Release. | ||
| tmnxMplsV8v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.8 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 8.0 Release. | ||
| tmnxMplsV9v0Compliance | 1.3.6.1.4.1.6527.3.1.1.6.1.9 | The compliance statement for management of extended MPLS on Alcatel-Lucent SROS series systems 9.0 Release. | ||
| tmnxMplsXCGroup | 1.3.6.1.4.1.6527.3.1.1.6.2.4 | The group of objects supporting management of extended MPLS LSP to cross-connection mapping on Alcatel-Lucent SROS series systems. | ||
| vRtrMplsAdminGroupEntry | 1.3.6.1.4.1.6527.3.1.2.6.13.1 | not-accessible | Each row entry in the vRtrMplsAdminGroupTable represents an administrative group which is simply a mapping between a group name (an ASCII string) and a group value (a number in the range 0 to 31). Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsAdminGroupRowStatus to 'createAndWait'. The row status for this entry can be set to active only once the value of vRtrMplsAdminGroupValue has been set to a valid number in the range 0 to 31. The entry is destroyed when vRtrMplsAdminGroupRowStatus is set to 'destroy'. | |
| TNA vRtrMplsAdminGroupName | 1.3.6.1.4.1.6527.3.1.2.6.13.1.1 | TNamedItem | not-accessible | The value of vRtrMplsAdminGroupName uniquely identifies the name of the administrative group within a virtual router instance. |
| ROW vRtrMplsAdminGroupRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.13.1.2 | RowStatus | read-create | vRtrMplsAdminGroupRowStatus is used to create, delete or control entries in the vRtrMplsAdminGroupTable. To create a row entry, the row status should be set to 'createAndWait'. Before the row can be placed into the 'active' state, vRtrMplsAdminGroupValue must be set to a value between 0 and 31. To delete a row entry, the row status should be set to 'destroy' |
| vRtrMplsAdminGroupTable | 1.3.6.1.4.1.6527.3.1.2.6.13 | not-accessible | The vRtrMplsAdminGroupTable has an entry for each administrative group configured for the virtual router in the system. Administrative groups are resource constructs that define a link color or resource class. They provide the ability to classify network resources (links) into groups or colors based on zones, geographic location, link location, etc. By doing so, network administrators are able to do more granular traffic engineering of LSPs. | |
| I32 vRtrMplsAdminGroupValue | 1.3.6.1.4.1.6527.3.1.2.6.13.1.3 | Integer32 | read-create | The value of vRtrMplsAdminGroupValue specifies the group value associated with this administrative group. This value is unique within a virtual router instance. A value of -1 indicates that the group value for this entry has not been set. |
| I32 vRtrMplsARHopTunnelIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.6 | Integer32 | read-only | Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list (stores RRO in LSR). |
| I32 vRtrMplsERHopTunnelIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.5 | Integer32 | read-only | Primary index into the mplsTunnelHopTable identifying a particular recorded hop list (stores ERO in LSR). |
| U32 vRtrMplsFSGroupCost | 1.3.6.1.4.1.6527.3.1.2.6.14.1.3 | Unsigned32 | read-create | The value of vRtrMplsFSGroupCost specifies the cost assigned to the fate sharing group. This cost is applied to all nodes and links that are part of this group and used for CSPF calculations. The higher the cost of the node or link, the lesser its chance of being selected as part of the path. |
| vRtrMplsFSGroupEntry | 1.3.6.1.4.1.6527.3.1.2.6.14.1 | not-accessible | Each row entry in the vRtrMplsFSGroupTable represents a fate sharing group which is a database of nodes and links that share common risk attributes. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupRowStatus to 'destroy'. | |
| TNA vRtrMplsFSGroupName | 1.3.6.1.4.1.6527.3.1.2.6.14.1.1 | TNamedItem | not-accessible | The value of vRtrMplsFSGroupName uniquely identifies the name of the fate sharing group within a virtual router instance. |
| vRtrMplsFSGroupParamsEntry | 1.3.6.1.4.1.6527.3.1.2.6.15.1 | not-accessible | Each row entry in the vRtrMplsFSGroupParamsTable represents either a node or a link that is a part of a fate sharing group defined in the vRtrMplsFSGroupTable. Entries in this table are created and deleted via SNMP SET operations. An entry is created by setting the value of vRtrMplsFSGroupParamsRowStatus to 'createAndGo'. An entry can be deleted by setting vRtrMplsFSGroupParamsRowStatus to 'destroy'. To configure a node to be part of the group, create an entry in this table with vRtrMplsFSGroupParamsFromAddr set to a valid non-zero IP address and vRtrMplsFSGroupParamsToAddr set to 0. To configure a link to be part of the group, create an entry in this table with both vRtrMplsFSGroupParamsFromAddr and vRtrMplsFSGroupParamsToAddr set to valid non-zero IP addresses. | |
| IP vRtrMplsFSGroupParamsFromAddr | 1.3.6.1.4.1.6527.3.1.2.6.15.1.1 | IpAddress | not-accessible | The value of vRtrMplsFSGroupParamsFromAddr along with the value of vRtrMplsFSGroupParamsToAddr uniquely identifies a link or node within a fate sharing group. This value must be non-zero for all row entries whether it represents a node or a link. |
| ROW vRtrMplsFSGroupParamsRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.15.1.3 | RowStatus | read-create | vRtrMplsFSGroupParamsRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupParamsTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy' |
| vRtrMplsFSGroupParamsTable | 1.3.6.1.4.1.6527.3.1.2.6.15 | not-accessible | The vRtrMplsFSGroupParamsTable has an entry for each node or link that is part of a fate sharing group on this virtual router. | |
| IP vRtrMplsFSGroupParamsToAddr | 1.3.6.1.4.1.6527.3.1.2.6.15.1.2 | IpAddress | not-accessible | The value of vRtrMplsFSGroupParamsToAddr along with the value of vRtrMplsFSGroupParamsFromAddr uniquely identifies a link or node within a fate sharing group. This value must be 0 for row entries that represent a node and must be non-zero for row entries that represent a link. |
| ROW vRtrMplsFSGroupRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.14.1.2 | RowStatus | read-create | vRtrMplsFSGroupRowStatus is used to create, delete or control entries in the vRtrMplsFSGroupTable. To create a row entry, the row status should be set to 'createAndGo'. To delete a row entry, the row status should be set to 'destroy' |
| vRtrMplsFSGroupTable | 1.3.6.1.4.1.6527.3.1.2.6.14 | not-accessible | The vRtrMplsFSGroupTable has an entry for each group that is a part of the fate sharing database configured for the virtual router in the system. A fate sharing group is used to define a group of links and nodes in the network that share common risk attributes. To minimize a single point of failure, backup paths can be created that not only avoid the nodes and links of the primary path but also any other nodes and links that share risk with the nodes and links of the primary path. | |
| TMN vRtrMplsGeneralAdminState | 1.3.6.1.4.1.6527.3.1.2.6.7.1.2 | TmnxAdminState | read-create | When vRtrMplsGeneralAdminState is set to 'inService', the agent attempts to enable the MPLS protocol instance on this router. When vRtrMplsGeneralAdminState is set to 'outOfService', the agent attempts to disable the MPLS protocol instance on this router. |
| U32 vRtrMplsGeneralAutoBWDefAdjMul | 1.3.6.1.4.1.6527.3.1.2.6.7.1.27 | Unsigned32 | read-create | The value of vRtrMplsGeneralAutoBWDefAdjMul specifies the global default for collection intervals in an adjust interval. |
| U32 vRtrMplsGeneralAutoBWDefSampMul | 1.3.6.1.4.1.6527.3.1.2.6.7.1.26 | Unsigned32 | read-create | The value of vRtrMplsGeneralAutoBWDefSampMul specifies the global default for collection intervals in a sample interval. |
| T/F vRtrMplsGeneralCspfOnLooseHop | 1.3.6.1.4.1.6527.3.1.2.6.7.1.29 | TruthValue | read-create | The value of vRtrMplsGeneralCspfOnLooseHop specifies whether the Constrained Shortest Path First (CSPF) calculation till the next loose hop is enabled or not. |
| G32 vRtrMplsGeneralDetourLspOriginate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.7 | Gauge32 | read-only | The value of vRtrMplsGeneralDetourLspOriginate indicates the number of detour LSPs that originate at this virtual router. |
| G32 vRtrMplsGeneralDetourLspTerminate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.9 | Gauge32 | read-only | The value of vRtrMplsGeneralDetourLspTerminate indicates the number of detour LSPs that terminate at this virtual router. |
| G32 vRtrMplsGeneralDetourLspTransit | 1.3.6.1.4.1.6527.3.1.2.6.8.1.8 | Gauge32 | read-only | The value of vRtrMplsGeneralDetourLspTransit indicates the number of detour LSPs that transit through this virtual router. |
| T/F vRtrMplsGeneralDynamicBypass | 1.3.6.1.4.1.6527.3.1.2.6.7.1.11 | TruthValue | read-create | The value of vRtrMplsGeneralDynamicBypass specifies whether dynamic bypass tunnels are enabled. By default, dynamic bypass tunnels are enabled. |
| G32 vRtrMplsGeneralDynamicLspOriginate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.4 | Gauge32 | read-only | The value of vRtrMplsGeneralDynamicLspOriginate indicates the number of dynamic LSPs that originate at this virtual router. |
| G32 vRtrMplsGeneralDynamicLspTerminate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.6 | Gauge32 | read-only | The value of vRtrMplsGeneralDynamicLspTerminate indicates the number of dynamic LSPs that terminate at this virtual router. |
| G32 vRtrMplsGeneralDynamicLspTransit | 1.3.6.1.4.1.6527.3.1.2.6.8.1.5 | Gauge32 | read-only | The value of vRtrMplsGeneralDynamicLspTransit indicates the number of dynamic LSPs that transit through this virtual router. |
| vRtrMplsGeneralEntry | 1.3.6.1.4.1.6527.3.1.2.6.7.1 | not-accessible | Each row entry represents an instance of the MPLS protocol running within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created by the agent when vRtrMplsStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrMplsStatus is set to 'delete' | |
| T/F vRtrMplsGeneralExpBackoffRetry | 1.3.6.1.4.1.6527.3.1.2.6.7.1.28 | TruthValue | read-create | The value of vRtrMplsGeneralExpBackoffRetry specifies the state of Exponential Backoff Retry mechanism. |
| T/F vRtrMplsGeneralFRObject | 1.3.6.1.4.1.6527.3.1.2.6.7.1.8 | TruthValue | read-create | The value of vRtrMplsGeneralFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsGeneralFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. The value for vRtrMplsGeneralFRObject is by default inherited by all LSPs. |
| U32 vRtrMplsGeneralHoldTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.10 | Unsigned32 | read-create | The value of vRtrMplsGeneralHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. A value of 0 indicates that the hold timer has been disabled. |
| TIM vRtrMplsGeneralLastChange | 1.3.6.1.4.1.6527.3.1.2.6.7.1.1 | TimeStamp | read-only | The sysUpTime when this row was last modified. |
| U32 vRtrMplsGeneralLeastFillMinThd | 1.3.6.1.4.1.6527.3.1.2.6.7.1.17 | Unsigned32 | read-create | The value of vRtrMplsGeneralLeastFillMinThd specifies in percentage the least minimum threshold parameter used in the least-fill path selection process. When comparing the percentage of least available link bandwidth across the sorted paths, whenever two percentages differ by less than the value configured as the vRtrMplsGeneralLeastFillMinThd, CSPF will consider them equal and will apply a random number generator to select the path among these paths. |
| C32 vRtrMplsGeneralLspEgrStatCount | 1.3.6.1.4.1.6527.3.1.2.6.8.1.13 | Counter32 | read-only | The value of vRtrMplsGeneralLspEgrStatCount indicates the number of LSP egress statistics configured on this virtual router. |
| C32 vRtrMplsGeneralLspIgrStatCount | 1.3.6.1.4.1.6527.3.1.2.6.8.1.14 | Counter32 | read-only | The value of vRtrMplsGeneralLspIgrStatCount indicates the number of LSP ingress statistics configured on this virtual router. |
| TES vRtrMplsGeneralNewLspIndex | 1.3.6.1.4.1.6527.3.1.2.6.7.1.6 | TestAndIncr | read-create | This object is used to assign values to vRtrMplsLspIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsLspEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions. |
| TES vRtrMplsGeneralNewP2mpInstIndex | 1.3.6.1.4.1.6527.3.1.2.6.7.1.16 | TestAndIncr | read-create | The value of vRtrMplsGeneralNewP2mpInstIndex specifies the object that is used to assign values to vRtrMplsP2mpInstIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET request that creates a new instance of vRtrMplsP2mpInstEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated. If the the SET succeeds, then the object is incremented and the new instance is created according to the manager's directions. |
| U32 vRtrMplsGeneralNextResignal | 1.3.6.1.4.1.6527.3.1.2.6.7.1.12 | Unsigned32 | read-only | The value of vRtrMplsGeneralNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralResignalTimer to expire. |
| TMN vRtrMplsGeneralOperDownReason | 1.3.6.1.4.1.6527.3.1.2.6.7.1.13 | TmnxMplsOperDownReasonCode | read-only | The value of vRtrMplsGeneralOperDownReason indicates the reason due to which the MPLS instance is operationally down. |
| TMN vRtrMplsGeneralOperState | 1.3.6.1.4.1.6527.3.1.2.6.7.1.3 | TmnxOperState | read-only | vRtrMplsGeneralOperState indicates the current operating state of this MPLS protocol instance on this router. |
| U32 vRtrMplsGeneralOptimizeTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.7 | Unsigned32 | read-create | The value of vRtrMplsGeneralOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSPs. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. The value for vRtrMplsGeneralOptimizeTimer is by default inherited by all LSPs and their paths. |
| U32 vRtrMplsGeneralP2mpNextResignal | 1.3.6.1.4.1.6527.3.1.2.6.7.1.21 | Unsigned32 | read-only | The value of vRtrMplsGeneralP2mpNextResignal indicates the time remaining, in minutes, for the vRtrMplsGeneralP2mpResigTimer to expire. |
| U32 vRtrMplsGeneralP2mpResigTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.20 | Unsigned32 | read-create | The value of vRtrMplsGeneralP2mpResigTimer specifies the value for the P2MP (point to multi point) LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the P2MP LSPs. When the resignal timer expires, an attempt to resignal the entire P2MP instance comprising all source to leaf (S2Ls) are done, the IGP or TE metric of the S2Ls are not taken into consideration. If the attempt to resignal an P2MP LSP fails, the P2MP LSP will continue to use the existing S2Ls and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based P2MP LSP resignalling has been disabled. |
| U32 vRtrMplsGeneralP2PMaxByPassAssoc | 1.3.6.1.4.1.6527.3.1.2.6.7.1.30 | Unsigned32 | read-create | The value of vRtrMplsGeneralP2PMaxByPassAssoc specifies the maximum number of LSP primary paths that can associate with each manual or dynamic bypass point-to-point (P2P) LSP. |
| T/F vRtrMplsGeneralPropagateTtl | 1.3.6.1.4.1.6527.3.1.2.6.7.1.4 | TruthValue | read-create | When vRtrMplsGeneralPropagateTtl is set to 'true', for all LSPs, the ingress ESR writes the TTL of the IP packet in the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When vRtrMplsGeneralPropagateTtl is set to 'false', the ingress ESR ignores the IP packet TTl and writes the value of 255 into the label, while the egress ESR does not write the label TTL into the IP packet. This assumes that all ESRs have been configured to have vRtrMplsGeneralPropagateTtl set to 'false', or this may result in unpredictable behavior. |
| U32 vRtrMplsGeneralResignalTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.9 | Unsigned32 | read-create | The value of vRtrMplsGeneralResignalTimer specifies the value for the P2P (point-to-point) LSP resignal timer, that is the time, in minutes, the software will wait before attempting to resignal the P2P LSPs. When the resignal timer expires, if the new recorded hop list (RRO) for an P2P LSP has a better metric than the current recorded hop list, an attempt will be made to resignal that P2P LSP using the make-before-break mechanism. If the attempt to resignal an P2P LSP fails, the P2P LSP will continue to use the existing path and a resignal will be attempted the next time the timer expires. A value of 0 for the resignal timer indicates that timer-based P2P LSP resignalling has been disabled. |
| G32 vRtrMplsGeneralS2lOriginate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.10 | Gauge32 | read-only | The value of vRtrMplsGeneralS2lOriginate indicates the number of source to leaf (S2L) sub LSP path called as S2L here that originate at this virtual router. |
| G32 vRtrMplsGeneralS2lTerminate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.12 | Gauge32 | read-only | The value of vRtrMplsGeneralS2lOriginate indicates the number of S2Ls that terminate at this virtual router. |
| G32 vRtrMplsGeneralS2lTransit | 1.3.6.1.4.1.6527.3.1.2.6.8.1.11 | Gauge32 | read-only | The value of vRtrMplsGeneralS2lOriginate indicates the number of S2Ls that transit through this virtual router. |
| U32 vRtrMplsGeneralSecFastRetryTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.22 | Unsigned32 | read-create | The value of vRtrMplsGeneralSecFastRetryTimer specifies the value, in seconds, used as fast retry timer for a secondary path. If the first attempt to setup a secondary path fails due to a path error, the fast retry timer will be started for the secondary path so that the path can be retried sooner. If the next attempt also fails, further retries for the path will use the configured value for LSP retry timer, vRtrMplsLspRetryTimer. If retry-timer for the LSP is configured to be less than the MPLS secondary-fast-retry-timer, all retries for the secondary path will use the LSP retry-timer. A value of 0 indicates that fast retry for secondary paths has been disabled. |
| T/F vRtrMplsGeneralShortTTLPropLocal | 1.3.6.1.4.1.6527.3.1.2.6.7.1.23 | TruthValue | read-create | The value of vRtrMplsGeneralShortTTLPropLocal specifies whether or not to enable the propagation of time to live (TTL) from the IP packet header into the header of the resulting MPLS packet for all local packets forwarded over a LSP shortcut. When the value is 'true' TTL is propagated from the IP packet header into the header of the resulting MPLS packet. |
| T/F vRtrMplsGeneralShortTTLPropTrans | 1.3.6.1.4.1.6527.3.1.2.6.7.1.24 | TruthValue | read-create | The value of vRtrMplsGeneralShortTTLPropTrans specifies whether or not to enable the propagation of time to live (TTL) from the IP packet header into the header of the resulting MPLS packet for all transit packets forwarded over a LSP shortcut. When the value is 'true' TTL is propagated from the IP packet header into the header of the resulting MPLS packet. |
| T/F vRtrMplsGeneralSrlgFrr | 1.3.6.1.4.1.6527.3.1.2.6.7.1.14 | TruthValue | read-create | The value of vRtrMplsGeneralSrlgFrr specifies whether Shared Risk Link Group (SRLG) constraint will be used in the computation of FRR bypass or detour to be associated with any primary LSP path on the system. When the value of vRtrMplsGeneralSrlgFrr is 'true' the use of SRLG constraint is enabled. By default, the use of SRLG constraint is disabled. |
| T/F vRtrMplsGeneralSrlgFrrStrict | 1.3.6.1.4.1.6527.3.1.2.6.7.1.15 | TruthValue | read-create | The value of vRtrMplsGeneralSrlgFrrStrict specifies whether to associate the LSP with a bypass or signal a detour if a bypass or detour satisfies all other constraints except the SRLG constraints. When the value of vRtrMplsGeneralSrlgFrrStrict is 'true' and a path that meets SRLG constraints is not found, the bypass or detour is not setup. If this value is set to 'true' when vRtrMplsGeneralSrlgFrr is set to 'false', vRtrMplsGeneralSrlgFrr is set to 'true' also. By default, the value of vRtrMplsGeneralSrlgFrrStrict is 'false'. |
| vRtrMplsGeneralStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.8.1 | not-accessible | Each row entry represents a collection of statistics for an instance of the MPLS protocol running within a virtual router. Entries cannot be created and deleted via SNMP SET operations. | |
| U32 vRtrMplsGeneralStaticLspFRTimer | 1.3.6.1.4.1.6527.3.1.2.6.7.1.25 | Unsigned32 | read-create | The value of vRtrMplsGeneralStaticLspFRTimer specifies the audit time for static LSPs which are not currently up. |
| G32 vRtrMplsGeneralStaticLspOriginate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.1 | Gauge32 | read-only | The value of vRtrMplsGeneralStaticLspOriginate indicates the number of static LSPs that originate at this virtual router. |
| G32 vRtrMplsGeneralStaticLspTerminate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.3 | Gauge32 | read-only | The value of vRtrMplsGeneralStaticLspTerminate indicates the number of static LSPs that terminate at this virtual router. |
| G32 vRtrMplsGeneralStaticLspTransit | 1.3.6.1.4.1.6527.3.1.2.6.8.1.2 | Gauge32 | read-only | The value of vRtrMplsGeneralStaticLspTransit indicates the number of static LSPs that transit through this virtual router. |
| vRtrMplsGeneralStatTable | 1.3.6.1.4.1.6527.3.1.2.6.8 | not-accessible | The vRtrMplsGeneralStatTable contains statistics for an MPLS protocol instance within a virtual router. | |
| vRtrMplsGeneralTable | 1.3.6.1.4.1.6527.3.1.2.6.7 | not-accessible | The vRtrMplsGeneralTable contains objects for general control and management of an MPLS protocol instance within a virtual router. | |
| INT vRtrMplsGeneralTE | 1.3.6.1.4.1.6527.3.1.2.6.7.1.5 | INTEGER | read-create | The value of vRtrMplsGeneralTE specifies the type of traffic engineering used with this MPLS instance. |
| T/F vRtrMplsGeneralUseSrlgDB | 1.3.6.1.4.1.6527.3.1.2.6.7.1.19 | TruthValue | read-create | The value of vRtrMplsGeneralUseSrlgDB specifies whether the use of the user SRLG database by CSPF is enabled. |
| T/F vRtrMplsGenIssuMplsLockdown | 1.3.6.1.4.1.6527.3.1.2.6.7.1.39 | TruthValue | read-only | The value of vRtrMplsGenIssuMplsLockdown indicates if MPLS has entered the state of not accepting new requests for creation of LSP's(local/transit) during the minor ISSU(In Service Software Update) operation. |
| U32 vRtrMplsGenLeastFillReoptiThd | 1.3.6.1.4.1.6527.3.1.2.6.7.1.18 | Unsigned32 | read-create | The value of vRtrMplsGenLeastFillReoptiThd specifies in percentage the least reoptimization threshold parameter used in the least-fill path selection process. During a timer-based re-signaling of an LSP path which has vRtrMplsLspLeastFill enabled, CSPF will first update the least-available bandwidth figure for the current path of this LSP. It then applies the least-fill path selection method to select a new path for this LSP. If the new computed path has the same cost as the current path, it will compare the least-available bandwidth figures of the two paths and if the difference exceeds vRtrMplsGenLeastFillReoptiThd, a trap will be generated to indicate that a better least-fill path is available for this LSP. |
| U32 vRtrMplsGenLspInitRetryTimeout | 1.3.6.1.4.1.6527.3.1.2.6.7.1.33 | Unsigned32 | read-create | The value of vRtrMplsGenLspInitRetryTimeout specifies the amount of time in seconds the software waits for an LSP path to come up after sending out the initial Path message. If the initial retry timeout period expires and the LSP path is not up, it is torn down and the LSP retry timer is started to schedule a new retry cycle using a new LSP-id. |
| G32 vRtrMplsGenMplsTpLspOriginate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.15 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpLspOriginate indicates the number of MPLS TP LSPs that originate at this virtual router. |
| G32 vRtrMplsGenMplsTpLspTerminate | 1.3.6.1.4.1.6527.3.1.2.6.8.1.17 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpLspTerminate indicates the number of MPLS TP LSPs that terminate at this virtual router. |
| G32 vRtrMplsGenMplsTpLspTransit | 1.3.6.1.4.1.6527.3.1.2.6.8.1.16 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpLspTransit indicates the number of MPLS TP LSPs that transit through this virtual router. |
| G32 vRtrMplsGenMplsTpOrigPathInst | 1.3.6.1.4.1.6527.3.1.2.6.8.1.18 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpOrigPathInst indicates the number of MPLS TP LSPs originate path instances. |
| G32 vRtrMplsGenMplsTpTermPathInst | 1.3.6.1.4.1.6527.3.1.2.6.8.1.20 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpTermPathInst indicates the number of MPLS TP LSPs terminated path instances. |
| G32 vRtrMplsGenMplsTpTranPathInst | 1.3.6.1.4.1.6527.3.1.2.6.8.1.19 | Gauge32 | read-only | The value of vRtrMplsGenMplsTpTranPathInst indicates the number of MPLS TP LSPs transit path instances. |
| U32 vRtrMplsGenP2mpS2lFastRetry | 1.3.6.1.4.1.6527.3.1.2.6.7.1.32 | Unsigned32 | read-create | The value of vRtrMplsGenP2mpS2lFastRetry specifies the time, in seconds, active path point to multipoint (P2MP) source to leaf (S2L) LSP waits before it attempts to re-establish itself. This timer is started after first attempt to setup active path P2MP S2L LSP fails. When vRtrMplsGenP2mpS2lFastRetry is set to 0, fast retry timer for active path P2MP S2L LSP is disabled. |
| U32 vRtrMplsGenP2pActPathFastRetry | 1.3.6.1.4.1.6527.3.1.2.6.7.1.31 | Unsigned32 | read-create | The value of vRtrMplsGenP2pActPathFastRetry specifies the time, in seconds, active path point-to-point (P2P) LSP waits before it attempts to re-establish itself. This timer is started after first attempt to setup active path P2P LSP fails. When vRtrMplsGenP2pActPathFastRetry is set to 0, fast retry timer for active path P2P LSP is disabled. |
| U32 vRtrMplsIfAdminGroup | 1.3.6.1.4.1.6527.3.1.2.6.9.1.3 | Unsigned32 | read-create | The value of vRtrMplsIfAdminGroup is a bit-map that identifies the admin groups to which the interface belongs. If bit 'n' is set, then the interface belongs to the admin group with value 'n'. By default, the interface does not belong to any admin groups. |
| TMN vRtrMplsIfAdminState | 1.3.6.1.4.1.6527.3.1.2.6.9.1.1 | TmnxAdminState | read-create | The desired administrative state for the MPLS protocol running on this MPLS interface. |
| vRtrMplsIfEntry | 1.3.6.1.4.1.6527.3.1.2.6.9.1 | not-accessible | Each row entry represents an interface on this virtual router that participates in the MPLS protocol. A row cannot be created or deleted via SNMP SET requests. A row with default attribute values is created by setting the vRtrIfEntry attribute, vRtrIfMplsStatus, to 'create'. A row is removed if vRtrIfMplsStatus is set to 'delete'. However, an attempt to destroy a row will fail if vRtrMplsIfAdminState has not first been set to 'outOfService'. | |
| TMN vRtrMplsIfOperState | 1.3.6.1.4.1.6527.3.1.2.6.9.1.2 | TmnxOperState | read-only | This variable indicates the current status of the MPLS protocol running on this MPLS interface. When the TIMETRA-VRTR-MIB::vRtrIfPortID object of this interface is set to a loopback port identifier, the operational state is not relevant and an SNMP GET request on this object will return 'unknown'. |
| C64 vRtrMplsIfRxOctetCount | 1.3.6.1.4.1.6527.3.1.2.6.10.1.4 | Counter64 | read-only | The total number of bytes in MPLS labeled packets received on this interface. |
| C64 vRtrMplsIfRxPktCount | 1.3.6.1.4.1.6527.3.1.2.6.10.1.2 | Counter64 | read-only | The total number of MPLS labeled packets received on this interface. |
| vRtrMplsIfSrlgGrpEntry | 1.3.6.1.4.1.6527.3.1.2.6.23.1 | not-accessible | Each row entry represents an SRLG group associated with a interface on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests. | |
| TIM vRtrMplsIfSrlgGrpLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.23.1.3 | TimeStamp | read-only | The value of vRtrMplsIfSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsIfSrlgGrpTable. |
| TNA vRtrMplsIfSrlgGrpName | 1.3.6.1.4.1.6527.3.1.2.6.23.1.1 | TNamedItem | not-accessible | The value of vRtrMplsIfSrlgGrpName indicates the SRLG group name. |
| ROW vRtrMplsIfSrlgGrpRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.23.1.2 | RowStatus | read-create | vRtrMplsIfSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsIfSrlgGrpTable. |
| vRtrMplsIfSrlgGrpTable | 1.3.6.1.4.1.6527.3.1.2.6.23 | not-accessible | The vRtrMplsIfSrlgGrpTable has an entry for each Shared Risk Link Group (SRLG) groups associated with a router interface configured for MPLS in the system. | |
| TIM vRtrMplsIfSrlgGrpTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.22 | TimeStamp | read-only | The value of vRtrMplsIfSrlgGrpTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsIfSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| NTF vRtrMplsIfStateChange | 1.3.6.1.4.1.6527.3.1.3.6.0.2 | This Notification is generated when the MPLS interface changes state | ||
| vRtrMplsIfStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.10.1 | not-accessible | Each row entry represents a collection of statistics for an interface on this virtual router that participates in the MPLS protocol. Entries cannot be created and deleted via SNMP SET operations. | |
| vRtrMplsIfStatTable | 1.3.6.1.4.1.6527.3.1.2.6.10 | not-accessible | The vRtrMplsIfStatTable has an entry for each router interface configured for MPLS in the system. | |
| vRtrMplsIfTable | 1.3.6.1.4.1.6527.3.1.2.6.9 | not-accessible | The vRtrMplsIfTable has an entry for each router interface configured for MPLS in the system. | |
| U32 vRtrMplsIfTeMetric | 1.3.6.1.4.1.6527.3.1.2.6.9.1.4 | Unsigned32 | read-create | The value of vRtrMplsIfTeMetric specifies the traffic engineering metric for this interface. The TE metric is exchanged in addition to the IGP metric by the IGPs. Depending on the value configured for vRtrMplsLspCspfTeMetricEnabled, either the TE metric or the native IGP metric is used in CSPF computations of the LSP paths. The maximum value that can be configured is a 24 bit value. |
| C64 vRtrMplsIfTxOctetCount | 1.3.6.1.4.1.6527.3.1.2.6.10.1.3 | Counter64 | read-only | The total number of bytes in MPLS labeled packets transmitted on this interface. |
| C64 vRtrMplsIfTxPktCount | 1.3.6.1.4.1.6527.3.1.2.6.10.1.1 | Counter64 | read-only | The total number of MPLS labeled packets transmitted from this interface. |
| C64 vRtrMplsInProfileOctetsFc0 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.25 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc0 indicates the number of in profile octets received for Forwarding Class 0. |
| C32 vRtrMplsInProfileOctetsFc0High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.27 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc0 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc0. |
| C32 vRtrMplsInProfileOctetsFc0Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.26 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc0 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc0. |
| C64 vRtrMplsInProfileOctetsFc1 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.28 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc1 indicates the number of in profile octets received for Forwarding Class 1. |
| C32 vRtrMplsInProfileOctetsFc1High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.30 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc1 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc1. |
| C32 vRtrMplsInProfileOctetsFc1Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.29 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc1 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc1. |
| C64 vRtrMplsInProfileOctetsFc2 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.31 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc2 indicates the number of in profile octets received for Forwarding Class 2. |
| C32 vRtrMplsInProfileOctetsFc2High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.33 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc2 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc2. |
| C32 vRtrMplsInProfileOctetsFc2Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.32 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc2 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc2. |
| C64 vRtrMplsInProfileOctetsFc3 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.34 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc3 indicates the number of in profile octets received for Forwarding Class 3. |
| C32 vRtrMplsInProfileOctetsFc3High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.36 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc3 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc3. |
| C32 vRtrMplsInProfileOctetsFc3Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.35 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc3 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc3. |
| C64 vRtrMplsInProfileOctetsFc4 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.37 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc4 indicates the number of in profile octets received for Forwarding Class 4. |
| C32 vRtrMplsInProfileOctetsFc4High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.39 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc4 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc4. |
| C32 vRtrMplsInProfileOctetsFc4Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.38 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc4 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc4. |
| C64 vRtrMplsInProfileOctetsFc5 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.40 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc5 indicates the number of in profile octets received for Forwarding Class 5. |
| C32 vRtrMplsInProfileOctetsFc5High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.42 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc5 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc5. |
| C32 vRtrMplsInProfileOctetsFc5Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.41 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc5 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc5. |
| C64 vRtrMplsInProfileOctetsFc6 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.43 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc6 indicates the number of in profile octets received for Forwarding Class 6. |
| C32 vRtrMplsInProfileOctetsFc6High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.45 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc6 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc6. |
| C32 vRtrMplsInProfileOctetsFc6Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.44 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc6 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc6. |
| C64 vRtrMplsInProfileOctetsFc7 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.46 | Counter64 | read-only | The value of vRtrMplsInProfileOctetsFc7 indicates the number of in profile octets received for Forwarding Class 7. |
| C32 vRtrMplsInProfileOctetsFc7High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.48 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc7 indicates the higher 32 bits of the value of vRtrMplsInProfileOctetsFc7. |
| C32 vRtrMplsInProfileOctetsFc7Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.47 | Counter32 | read-only | The value of vRtrMplsInProfileOctetsFc7 indicates the lower 32 bits of the value of vRtrMplsInProfileOctetsFc7. |
| C64 vRtrMplsInProfilePktsFc0 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.1 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc0 indicates the number of in profile packets received for Forwarding Class 0. |
| C32 vRtrMplsInProfilePktsFc0High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.3 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc0 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc0. |
| C32 vRtrMplsInProfilePktsFc0Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.2 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc0 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc0. |
| C64 vRtrMplsInProfilePktsFc1 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.4 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc1 indicates the number of in profile packets received for Forwarding Class 1. |
| C32 vRtrMplsInProfilePktsFc1High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.6 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc1 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc1. |
| C32 vRtrMplsInProfilePktsFc1Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.5 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc1 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc1. |
| C64 vRtrMplsInProfilePktsFc2 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.7 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc2 indicates the number of in profile packets received for Forwarding Class 2. |
| C32 vRtrMplsInProfilePktsFc2High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.9 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc2 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc2. |
| C32 vRtrMplsInProfilePktsFc2Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.8 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc2 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc2. |
| C64 vRtrMplsInProfilePktsFc3 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.10 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc3 indicates the number of in profile packets received for Forwarding Class 3. |
| C32 vRtrMplsInProfilePktsFc3High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.12 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc3 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc3. |
| C32 vRtrMplsInProfilePktsFc3Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.11 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc3 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc3. |
| C64 vRtrMplsInProfilePktsFc4 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.13 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc4 indicates the number of in profile packets received for Forwarding Class 4. |
| C32 vRtrMplsInProfilePktsFc4High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.15 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc4 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc4. |
| C32 vRtrMplsInProfilePktsFc4Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.14 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc4 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc4. |
| C64 vRtrMplsInProfilePktsFc5 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.16 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc5 indicates the number of in profile packets received for Forwarding Class 5. |
| C32 vRtrMplsInProfilePktsFc5High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.18 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc5 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc5. |
| C32 vRtrMplsInProfilePktsFc5Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.17 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc5 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc5. |
| C64 vRtrMplsInProfilePktsFc6 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.19 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc6 indicates the number of in profile packets received for Forwarding Class 6. |
| C32 vRtrMplsInProfilePktsFc6High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.21 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc6 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc6. |
| C32 vRtrMplsInProfilePktsFc6Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.20 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc6 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc6. |
| C64 vRtrMplsInProfilePktsFc7 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.22 | Counter64 | read-only | The value of vRtrMplsInProfilePktsFc7 indicates the number of in profile packets received for Forwarding Class 7. |
| C32 vRtrMplsInProfilePktsFc7High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.24 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc7 indicates the higher 32 bits of the value of vRtrMplsInProfilePktsFc7. |
| C32 vRtrMplsInProfilePktsFc7Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.23 | Counter32 | read-only | The value of vRtrMplsInProfilePktsFc7 indicates the lower 32 bits of the value of vRtrMplsInProfilePktsFc7. |
| vRtrMplsInSegmentEntry | 1.3.6.1.4.1.6527.3.1.2.6.34.1 | not-accessible | A row entry in this table corresponds to a row entry in the mplsInSegmentTable and adds to the information contained in that table. | |
| NUM vRtrMplsInSegmentIfIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.2 | InterfaceIndexOrZero | read-only | An index of the mplsXCTable. It represents mplsInSegmentIfIndex of the mplsInSegmentTable. |
| MPL vRtrMplsInSegmentLabel | 1.3.6.1.4.1.6527.3.1.2.6.6.1.3 | MplsLabel | read-only | An index of the mplsXCTable. It represents mplsInSegmentLabel of the mplsInSegmentTable. |
| U32 vRtrMplsInSegmentNumS2ls | 1.3.6.1.4.1.6527.3.1.2.6.34.1.1 | Unsigned32 | read-only | The value of vRtrMplsInSegmentNumS2ls specifies number of S2Ls on the insegment. |
| vRtrMplsInSegmentTable | 1.3.6.1.4.1.6527.3.1.2.6.34 | not-accessible | The vRtrMplsInSegmentTable augments the mplsInSegmentTable in the MPLS-LSR-MIB. | |
| U32 vRtrMplsLabelMaxStaticLspLabels | 1.3.6.1.4.1.6527.3.1.2.6.45.1 | Unsigned32 | read-write | The value of vRtrMplsLabelMaxStaticLspLabels specifies the maximum number of Static LSP labels available on the system. vRtrMplsLabelMaxStaticLspLabels must be set along with vRtrMplsLabelMaxStaticSvcLabels. The total of both values should equal the maximum value allowed of 131040 or 262112 depending on the system. The maximum value of vRtrMplsLabelMaxStaticLspLabels value for most systems is 113040 labels (128 * 1024 less 32 reserved labels). The maximum value of vRtrMplsLabelMaxStaticLspLabels value for chassis mode D systems is 262112 labels (256 * 1024 less 32 reserved labels). |
| U32 vRtrMplsLabelMaxStaticSvcLabels | 1.3.6.1.4.1.6527.3.1.2.6.45.2 | Unsigned32 | read-write | The value of vRtrMplsLabelMaxStaticSvcLabels specifies the maximum number of Static SVC labels available on the system. vRtrMplsLabelMaxStaticSvcLabels must be set along with vRtrMplsLabelMaxStaticLspLabels. The total of both values should equal the maximum value allowed of 113040 or 262112 depending on the system. The maximum value of vRtrMplsLabelMaxStaticLspLabels value for most systems is 113040 labels (128 * 1024 less 32 reserved labels). The maximum value of vRtrMplsLabelMaxStaticLspLabels value for chassis mode D systems is 262112 labels (256 * 1024 less 32 reserved labels). |
| vRtrMplsLabelObjs | 1.3.6.1.4.1.6527.3.1.2.6.45 | |||
| U32 vRtrMplsLabelRangeAging | 1.3.6.1.4.1.6527.3.1.2.6.17.1.4 | Unsigned32 | read-only | The value of vRtrMplsLabelRangeAging represents the number of labels that are currently allocated and aging. |
| U32 vRtrMplsLabelRangeAvailable | 1.3.6.1.4.1.6527.3.1.2.6.17.1.5 | Unsigned32 | read-only | The value of vRtrMplsLabelRangeAvailable represents the number of labels that are currently available for each label type. |
| vRtrMplsLabelRangeEntry | 1.3.6.1.4.1.6527.3.1.2.6.17.1 | not-accessible | Each row entry in the vRtrMplsLabelRangeTable represents a type of label. Each entry contains the label range used by that label type and the number of aging and allocated labels in the range. | |
| U32 vRtrMplsLabelRangeMax | 1.3.6.1.4.1.6527.3.1.2.6.17.1.3 | Unsigned32 | read-only | The value of vRtrMplsLabelRangeMax specifies the maximum label value in the range for a particular label type. |
| U32 vRtrMplsLabelRangeMin | 1.3.6.1.4.1.6527.3.1.2.6.17.1.2 | Unsigned32 | read-only | The value of vRtrMplsLabelRangeMin specifies the minimum label value in the range for a particular label type. |
| vRtrMplsLabelRangeTable | 1.3.6.1.4.1.6527.3.1.2.6.17 | not-accessible | The vRtrMplsLabelRangeTable has an entry for each type of label, the minimum and maximum value in the label range and information on total available and aging labels in each range. This is a read-only table. | |
| INT vRtrMplsLabelType | 1.3.6.1.4.1.6527.3.1.2.6.17.1.1 | INTEGER | not-accessible | The value of vRtrMplsLabelType specifies the type of label and is the index for this table. |
| NTF vRtrMplsLblRangeModify | 1.3.6.1.4.1.6527.3.1.3.6.0.23 | [CAUSE] vRtrMplsLblRangeModify is generated when the values of vRtrMplsLabelMaxStaticLspLabels or vRtrMplsLabelMaxStaticSvcLabels have been modified. [EFFECT] The maximum static labels are modified. [RECOVERY] There is no recovery required for this notification. | ||
| T/F vRtrMplsLoggerEventBundling | 1.3.6.1.4.1.6527.3.1.2.6.7.1.34 | TruthValue | read-create | The value of vRtrMplsLoggerEventBundling specifies whether or not the notification bundling mechanism is enabled. When the value of vRtrMplsLoggerEventBundling is set to 'true', all TIMETRA-SYSTEM-MIB::tmnxConfigCreate and TIMETRA-SYSTEM-MIB::tmnxConfigDelete notifications that are generated because of creation or deletion of entries in the vRtrMplsXCTable during quiet period of 2 minutes are bundled in a single notification. An entry is created or deleted in vRtrMplsXCTable when a RSVP session is created or deleted on this ingress, transit or egress router instance causing creation or deletion of an entry in TIMETRA-RSVP-MIB::vRtrRsvpSessionTable. A vRtrMplsXCBundleChange notification is generated after every quiet interval of 2 minutes if one or more RSVP session changed state and retained that state during the quiet interval. However if the state of the RSVP sessions does not remain stable for an entire quiet interval, the notification is generated after the maximum interval period of 10 minutes has elapsed. |
| NTF vRtrMplsLspActivePathChanged | 1.3.6.1.4.1.6527.3.1.3.6.0.21 | [CAUSE] The vRtrMplsLspActivePathChanged notification is generated when the active path of an LSP successfully switches to an new path. This notification will also be sent when the active LSP path does not change but only the switch method changes on the path. The old LSP path index is specified by vRtrMplsLspOldTunnelIndex. The state and switch method of the current active LSP path are specified by vRtrMplsLspPathState and vRtrMplsLspPathActiveByManual respectively. [EFFECT] The switchover to the new LSP path was successful or/and switch method of the current active LSP path changed. [RECOVERY] There is no recovery required for this notification. | ||
| T/F vRtrMplsLspAdaptive | 1.3.6.1.4.1.6527.3.1.2.6.1.1.34 | TruthValue | read-create | Setting the value of vRtrMplsLspAdaptive to 'true' enables make-before-break functionality for the LSP. When the attributes of an already established LSP are changed, either through manual configuration or due to a change in network topology, make-before-break functionality ensures that the resources of the existing LSP will not be released until a new path (with the same LSP Id) has been established and traffic flowing over the existing path is seamlessly transferred to the new path. Setting the value to 'false' disables make-before-break functionality. |
| U32 vRtrMplsLspAdminGroupExclude | 1.3.6.1.4.1.6527.3.1.2.6.1.1.33 | Unsigned32 | read-create | The value of vRtrMplsLspAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP. This implies that each link that this LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list. |
| U32 vRtrMplsLspAdminGroupInclude | 1.3.6.1.4.1.6527.3.1.2.6.1.1.32 | Unsigned32 | read-create | The value of vRtrMplsLspAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP. This implies that each link that this LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list. |
| TMN vRtrMplsLspAdminState | 1.3.6.1.4.1.6527.3.1.2.6.1.1.5 | TmnxAdminState | read-create | The desired administrative state for this LSP. |
| NUM vRtrMplsLspAge | 1.3.6.1.4.1.6527.3.1.2.6.2.1.3 | TimeInterval | read-only | The age (i.e., time from creation till now) of this LSP in 10-millisecond periods. |
| T/F vRtrMplsLspAutoBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.1.1.50 | TruthValue | read-create | The value of the vRtrMplsLspAutoBandwidth specifies whether automatic bandwidth adjustment has been enabled or disabled for this LSP. A value of 'true' specifies that automatic bandwidth adjustment has been enabled for this LSP and a value of 'false' specifies that automatic bandwidth adjustment has been disabled for this LSP. |
| vRtrMplsLspAutoBandwidthEntry | 1.3.6.1.4.1.6527.3.1.2.6.43.1 | not-accessible | Each row entry represents auto bandwidth configuration for a Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| vRtrMplsLspAutoBandwidthTable | 1.3.6.1.4.1.6527.3.1.2.6.43 | not-accessible | The vRtrMplsLspAutoBandwidthTable has an entry for auto bandwidth configuration for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| U32 vRtrMplsLspAutoBWAdjCount | 1.3.6.1.4.1.6527.3.1.2.6.43.1.26 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWAdjCount indicates the count in the adjust interval. |
| U32 vRtrMplsLspAutoBWAdjDNMbps | 1.3.6.1.4.1.6527.3.1.2.6.43.1.4 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWAdjDNMbps specifies the minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for decreasing the bandwidth of the LSP. |
| U32 vRtrMplsLspAutoBWAdjDNPercent | 1.3.6.1.4.1.6527.3.1.2.6.43.1.3 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWAdjDNPercent specifies minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for decreasing the bandwidth of the LSP. At the adjust interval expiry, if the measured bandwidth falls below the current bandwidth by the value of vRtrMplsLspAutoBWAdjDNPercent it can cause a re-signaling attempt for the LSP When the value of vRtrMplsLspAutoBWAdjDNPercent is 0 it means that this threshold check is always true for any measured bandwidth less than current bandwidth |
| U32 vRtrMplsLspAutoBWAdjMultiplier | 1.3.6.1.4.1.6527.3.1.2.6.43.1.5 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWAdjMultiplier specifies the number of collection intervals in the adjust interval. The default value is derived from vRtrMplsGeneralAutoBWDefAdjMul and vRtrMplsLspAutoBWAdjCount. |
| U32 vRtrMplsLspAutoBWAdjTime | 1.3.6.1.4.1.6527.3.1.2.6.43.1.23 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWAdjTime indicates the adjust multipler times the collection interval. |
| U32 vRtrMplsLspAutoBWAdjUPMbps | 1.3.6.1.4.1.6527.3.1.2.6.43.1.7 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWAdjDNMbps specifies the minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as an absolute bandwidth (Mbps), for increasing the bandwidth of the LSP. |
| U32 vRtrMplsLspAutoBWAdjUPPercent | 1.3.6.1.4.1.6527.3.1.2.6.43.1.6 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWAdjUPPercent specifies minimum difference between the current bandwidth reservation of the LSP and the (measured) maximum average data rate, expressed as a percentage of the current bandwidth, for increasing the bandwidth of the LSP. At the adjust interval expiry, if the measured bandwidth exceeds the current bandwidth by the value of vRtrMplsLspAutoBWAdjUPPercent it can cause a re-signaling attempt for the LSP When the value of vRtrMplsLspAutoBWAdjUPPercent is 0 it means that this threshold check is always true for any measured bandwidth greater than current bandwidth |
| U32 vRtrMplsLspAutoBWCurrentBW | 1.3.6.1.4.1.6527.3.1.2.6.43.1.22 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWCurrentBW indicates the current bandwidth reserved along the primary path. |
| U32 vRtrMplsLspAutoBWInheritance | 1.3.6.1.4.1.6527.3.1.2.6.43.1.21 | Unsigned32 | read-write | For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspAutoBWInheritance that controls whether to inherit the operational value of the object or use the administratively set value. This object is a bit-mask, with the following positions: vRtrMplsLspAutoBWAdjMultiplier 0x1 vRtrMplsLspAutoBWSampMultiplier 0x2 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable. |
| TIM vRtrMplsLspAutoBWLastAdj | 1.3.6.1.4.1.6527.3.1.2.6.43.1.16 | TimeStamp | read-only | The value of vRtrMplsLspAutoBWLastAdj indicates the system time for the last auto-bandwidth adjustment. |
| TMN vRtrMplsLspAutoBWLastAdjCause | 1.3.6.1.4.1.6527.3.1.2.6.43.1.17 | TmnxMplsLspAutoBWLastAdjCause | read-only | The value of vRtrMplsLspAutoBWLastAdjCause indicates the cause for the last auto-bandwidth adjustment. |
| U32 vRtrMplsLspAutoBWLastAvgRate | 1.3.6.1.4.1.6527.3.1.2.6.43.1.20 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWLastAvgRate indicates the avegare data rate in the sample interval that ended most recently. |
| TIM vRtrMplsLspAutoBWLastChange | 1.3.6.1.4.1.6527.3.1.2.6.43.1.2 | TimeStamp | read-only | The sysUpTime when this row was last modified. |
| TNA vRtrMplsLspAutoBWLspName | 1.3.6.1.4.1.6527.3.1.2.6.43.1.1 | TNamedItem | not-accessible | The value of vRtrMplsLspAutoBWLspName uniquely identifies a row in the vRtrMplsLspAutoBandwidthTable. |
| U32 vRtrMplsLspAutoBWMaxAvgRate | 1.3.6.1.4.1.6527.3.1.2.6.43.1.19 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWMaxAvgRate indicates the maximum average data rate in any sample interval of the current adjust interval. |
| U32 vRtrMplsLspAutoBWMaxBW | 1.3.6.1.4.1.6527.3.1.2.6.43.1.8 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWMaxBW specifies the maximum that auto-bandwidth allocation is allowed to request for a LSP. |
| U32 vRtrMplsLspAutoBWMinBW | 1.3.6.1.4.1.6527.3.1.2.6.43.1.9 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWMinBW specifies the minimum that auto-bandwidth allocation is allowed to request for a LSP. |
| T/F vRtrMplsLspAutoBWMonitorBW | 1.3.6.1.4.1.6527.3.1.2.6.43.1.10 | TruthValue | read-write | The value of vRtrMplsLspAutoBWMonitorBW specifies whether the collection and display of auto-bandwidth measurements is enabled or disabled for the LSP. When the value of vRtrMplsLspAutoBWMonitorBW is 'true' the collection and display of auto-bandwidth measurements is enabled and when the value is 'false' it is disabled. |
| U32 vRtrMplsLspAutoBWNextAdj | 1.3.6.1.4.1.6527.3.1.2.6.43.1.18 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWNextAdj indicates the system time when then adjust-timer will expire. |
| TMN vRtrMplsLspAutoBWOperState | 1.3.6.1.4.1.6527.3.1.2.6.43.1.27 | TmnxEnabledDisabled | read-only | The value of vRtrMplsLspAutoBWOperState indicates the opertional status for the LSP. |
| U32 vRtrMplsLspAutoBWOverFlow | 1.3.6.1.4.1.6527.3.1.2.6.43.1.11 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWOverFlow specifies number of overflow samples that triggers an overflow auto-bandwidth adjustment attempt. |
| U32 vRtrMplsLspAutoBWOvrFlwBW | 1.3.6.1.4.1.6527.3.1.2.6.43.1.13 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWOvrFlwBW specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as an absolute bandwidth (Mbps), for counting an overflow sample. |
| U32 vRtrMplsLspAutoBWOvrFlwCount | 1.3.6.1.4.1.6527.3.1.2.6.43.1.24 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWOvrFlwCount indicates the number of overflow samples since the last reset. |
| U32 vRtrMplsLspAutoBWOvrFlwThreshold | 1.3.6.1.4.1.6527.3.1.2.6.43.1.12 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWOvrFlwThreshold specifies the minimum difference between the current bandwidth of the LSP and the sampled data rate, expressed as a percentage of the current bandwidth, for counting an overflow sample. |
| U32 vRtrMplsLspAutoBWSampCount | 1.3.6.1.4.1.6527.3.1.2.6.43.1.25 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWSampCount indicates the count in the sample interval. |
| U32 vRtrMplsLspAutoBWSampInterval | 1.3.6.1.4.1.6527.3.1.2.6.43.1.28 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWSampInterval indicates the number of sample intervals. |
| U32 vRtrMplsLspAutoBWSampMultiplier | 1.3.6.1.4.1.6527.3.1.2.6.43.1.14 | Unsigned32 | read-write | The value of vRtrMplsLspAutoBWSampMultiplier specifies the mulitplier for collection intervals in a sample interval. |
| U32 vRtrMplsLspAutoBWSampTime | 1.3.6.1.4.1.6527.3.1.2.6.43.1.15 | Unsigned32 | read-only | The value of vRtrMplsLspAutoBWSampTime indicates the sample multipler times the collection interval. |
| TIM vRtrMplsLspAutoBWTableLastChg | 1.3.6.1.4.1.6527.3.1.2.6.42 | TimeStamp | read-only | The value of vRtrMplsLspAutoBWTableLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsLspAutoBandwidthTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| I32 vRtrMplsLspBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.1.1.24 | Integer32 | read-create | The value of vRtrMplsLspBandwidth specifies the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the LSP. A value of zero (0) indicates that no bandwidth is reserved. When vRtrMplsLspPathBandwidth is set to -1, the value of vRtrMplsLspBandwidth is applied to that specific LSP/path. |
| T/F vRtrMplsLspBgpShortcut | 1.3.6.1.4.1.6527.3.1.2.6.1.1.53 | TruthValue | read-create | The value of vRtrMplsLspBgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspBgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving BGP routes. When the value of vRtrMplsLspBgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving BGP routes. |
| TMN vRtrMplsLspBgpTransportTunnel | 1.3.6.1.4.1.6527.3.1.2.6.1.1.54 | TmnxMplsLspBgpRSVPLSPTunState | read-create | The value of vRtrMplsLspBgpTransportTunnel specifies whether an RSVP LSP is allowed or blocked in its usage as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspBgpTransportTunnel is set to 'include' an RSVP LSP is allowed to be used as a transport LSP for BGP tunnel routes. When the value of vRtrMplsLspBgpTransportTunnel is set to 'exclude' an RSVP LSP is not allowed to be used as a transport LSP for BGP tunnel routes. |
| T/F vRtrMplsLspBwProtect | 1.3.6.1.4.1.6527.3.1.2.6.1.1.25 | TruthValue | read-create | When vRtrMplsLspBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources. |
| TNA vRtrMplsLspClassOfService | 1.3.6.1.4.1.6527.3.1.2.6.1.1.19 | TNamedItemOrEmpty | read-create | The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced. When the value of vRtrMplsLspPathCosSource is set to 'inherit', the value of vRtrMplsLspClassOfService is applied to that specific LSP/path. |
| TMN vRtrMplsLspClassType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.42 | TmnxRsvpDSTEClassType | read-create | The value of vRtrMplsLspClassType specifies the class type (CT) associated with this LSP. |
| I32 vRtrMplsLspConfiguredPaths | 1.3.6.1.4.1.6527.3.1.2.6.2.1.11 | Integer32 | read-only | The number of paths configured for this LSP. |
| G32 vRtrMplsLspConfP2mpInstances | 1.3.6.1.4.1.6527.3.1.2.6.2.1.14 | Gauge32 | read-only | The value of vRtrMplsLspConfP2mpInstances indicates the number of p2mp instances configured for this LSP. |
| T/F vRtrMplsLspCspf | 1.3.6.1.4.1.6527.3.1.2.6.1.1.15 | TruthValue | read-create | When the value of vRtrMplsLspCspf is 'true', CSPF computation for constrained-path LSP is enabled. When the value of vRtrMplsLspCspf is 'false' CSPF computation is disabled. |
| T/F vRtrMplsLspCspfTeMetricEnabled | 1.3.6.1.4.1.6527.3.1.2.6.1.1.40 | TruthValue | read-create | The value of vRtrMplsLspCspfTeMetricEnabled specifies whether the TE metric would be used for the purpose of the LSP path computation by CSPF. When the value of this object is 'false', the IGP metric is used to compute the path of the LSP by CSPF. |
| T/F vRtrMplsLspCspfToFirstLoose | 1.3.6.1.4.1.6527.3.1.2.6.1.1.51 | TruthValue | read-create | The value of the vRtrMplsLspCspfToFirstLoose specifies whether the CSPF calculation till the first loose hop on ingress Label Edge Router (LER) is enabled or disabled for this Labeled Switched Path(LSP). By default, the value of vRtrMplsLspCspfToFirstLoose is 'false' which specifies that the CSPF calculation is done to the destination of LSP. |
| T/F vRtrMplsLspDecrementTtl | 1.3.6.1.4.1.6527.3.1.2.6.1.1.14 | TruthValue | read-create | When the value of vRtrMplsLspDecrementTtl is 'true', the ingress ESR writes the TTL of the IP packet into the label and each transit ESR decrements the TTL in the label. At the egress ESR the TTL value from the label is written into the IP packet. When the value of vRtrMplsLspDecrementTtl is 'false', the ingress ESR ignores the IP packet TTL and writes the value of 255 into the label; and the egress ESR does not write the label's TTL into the IP packet. |
| TMN vRtrMplsLspDestGlobalId | 1.3.6.1.4.1.6527.3.1.2.6.1.1.65 | TmnxMplsTpGlobalID | read-create | The value of vRtrMplsLspDestGlobalId specifies the global identifier for an MPLS-TP Static LSP. A value of 0 indicates that a locally configured global identifier is to be used. |
| U32 vRtrMplsLspDestTunnelNum | 1.3.6.1.4.1.6527.3.1.2.6.1.1.66 | Unsigned32 | read-create | The value of vRtrMplsLspDestTunnelNum specifies the destination tunnel number of an MPLS-TP Static LSP. |
| NTF vRtrMplsLspDown | 1.3.6.1.4.1.6527.3.1.3.6.0.4 | This Notification is generated when a LSP transitions out of 'inService' state to any other state. | ||
| vRtrMplsLspEntry | 1.3.6.1.4.1.6527.3.1.2.6.1.1 | not-accessible | Each row entry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspName to have been assigned a valid value. | |
| IP vRtrMplsLspExcludeNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.1.1.59 | InetAddress | read-create | When vRtrMplsLspExcludeNodeAddr is set to non-zero value, XRO (Exclude Routers) object will be included in bypass path message with supplied IP address. SET the value to 0.0.0.0 to disable. |
| IPt vRtrMplsLspExcludeNodeAddrType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.58 | InetAddressType | read-create | The value of vRtrMplsLspExcludeNodeAddrType indicates the type of vRtrMplsLspExcludeNodeAddr. |
| T/F vRtrMplsLspFastReroute | 1.3.6.1.4.1.6527.3.1.2.6.1.1.16 | TruthValue | read-create | When the value of vRtrMplsLspFastReroute is 'true', fast reroute is enabled. A pre-computed detour LSP is created from each node in the primary path of this LSP. In case of a failure of a link or LSP between two nodes, traffic is immediately rerouted on the pre-computed detour LSP thus avoiding packet loss. Each node along the primary path of the LSP tries to establish a detour LSP as follows: Each upstream node will setup a detour LSP that avoids only the immediate downstream node and merges back onto the actual path of the LSP as soon as possible. The detour LSP may take one or more hops (upto the value of vRtrMplsLspFRHopLimit) before merging back onto the main LSP path. When the upstream node detects a downstream link or node failure, it immediately send traffic for that LSP on the detour path and at the same time signals back to the ingress ESR about the failure. Fast reroute applies only to the primary path of this LSP. No configuration is required on the transit hops of the LSP. The ingress ESR will signal all intermediate ESRs using RSVP to setup their detours. When the value of vRtrMplsLspFastReroute is 'false', fast rerouting is disabled. |
| U32 vRtrMplsLspFRBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.1.1.18 | Unsigned32 | read-create | The value of vRtrMplsLspFRBandwidth specified the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the detour LSP. A value of zero (0) indicates that no bandwidth is reserved. |
| U32 vRtrMplsLspFRHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.1.1.17 | Unsigned32 | read-create | The value of vRtrMplsLspFRHopLimit specifies the total number of hops a detour LSP can take before merging back onto the main LSP path. |
| INT vRtrMplsLspFRMethod | 1.3.6.1.4.1.6527.3.1.2.6.1.1.30 | INTEGER | read-create | The value of vRtrMplsLspFRMethod specifies the fast reroute method used. In the 'One-to-one Backup' method, a backup LSP is established which will intersect the original LSP somewhere downstream of the point of link or node failure. For each LSP that is backed up, a separate backup LSP is established. In the 'Facility Backup' method, instead of creating a separate LSP for every LSP that is to be backed up, a single LSP is created which serves as a backup for a set of LSPs. Such an LSP tunnel is called a 'bypass tunnel'. |
| T/F vRtrMplsLspFRNodeProtect | 1.3.6.1.4.1.6527.3.1.2.6.1.1.31 | TruthValue | read-create | Setting the value of vRtrMplsLspFRNodeProtect to 'true' enables node protection i.e. protection against the failure of a node on the LSP. Setting the value to 'false' disables node protection. |
| T/F vRtrMplsLspFRObject | 1.3.6.1.4.1.6527.3.1.2.6.1.1.38 | TruthValue | read-create | The value of vRtrMplsLspFRObject specifies whether fast reroute, for LSPs using 'Facility Backup', is signalled with or without the fast reroute object. The value of vRtrMplsLspFRObject is ignored if fast reroute is disabled for the LSP or if the LSP is using 'One-to-one Backup'. When the vRtrMplsLspFRObject bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralFRObject. |
| IP vRtrMplsLspFromAddr | 1.3.6.1.4.1.6527.3.1.2.6.1.1.7 | IpAddress | read-create | Source IP address of this LSP. If vRtrMplsLspFromAddr has not been explicitly set, the system IP address will be used. |
| TMN vRtrMplsLspFromAddrType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.62 | TmnxMplsLspAddrType | read-create | The vRtrMplsLspFromAddrType object is an enumerated value that specifies the source address type of the LSP. When the value of vRtrMplsLspFromAddrType is 'ipv4', it specifies an IPv4 address type and vRtrMplsLspFromAddr should be configured. When the value of vRtrMplsLspFromAddrType is 'nodeId', it specifies an MPLS-TP node id type and vRtrMplsLspFromNodeId should be configured. |
| TMN vRtrMplsLspFromNodeId | 1.3.6.1.4.1.6527.3.1.2.6.1.1.64 | TmnxMplsTpNodeID | read-create | The value of vRtrMplsLspFromNodeId specifies the source node id of an MPLS-TP Static LSP. vRtrMplsLspFromNodeId is configured when vRtrMplsLspFromAddrType is set to 'nodeId'. |
| U32 vRtrMplsLspHoldPriority | 1.3.6.1.4.1.6527.3.1.2.6.1.1.21 | Unsigned32 | read-create | The value of vRtrMplsLspHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathHoldPriority is set to '-1', the value of vRtrMplsLspHoldPriority is applied to that specific LSP/path. |
| U32 vRtrMplsLspHoldTimer | 1.3.6.1.4.1.6527.3.1.2.6.1.1.39 | Unsigned32 | read-only | The value of vRtrMplsLspHoldTimer specifies the time, in seconds, for which the ingress node holds a bit before programming its data plane and declaring the lsp up to the service module. The value of vRtrMplsLspHoldTimer is inherited from the value of vRtrMplsGeneralHoldTimer. |
| U32 vRtrMplsLspHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.1.1.26 | Unsigned32 | read-create | The value of vRtrMplsLspHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the value of vRtrMplsLspPathHopLimit is set to zero (0), the value of vRtrMplsLspHopLimit is applied to that specific LSP/path. |
| T/F vRtrMplsLspIgpShortcut | 1.3.6.1.4.1.6527.3.1.2.6.1.1.48 | TruthValue | read-create | The value of vRtrMplsLspIgpShortcut specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspIgpShortcut is set to 'true' the RSVP LSP is used as a shortcut while resolving IGP routes. When the value of vRtrMplsLspIgpShortcut is set to 'false' the RSVP LSP is not used as a shortcut while resolving IGP routes. |
| INT vRtrMplsLspIgpShortcutLfaType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.60 | INTEGER | read-create | The value of vRtrMplsLspIgpShortcutLfaType specifies whether to exclude or include a RSVP LSP from being used as a shortcut while resolving IGP routes in LFA SPF or whether to exclude or include a RSVP LSP from being used as a LFA SPF. When the value of vRtrMplsLspIgpShortcutLfaType is set to 'lfaProtect' the RSVP LSP is used as a shortcut while resolving IGP routes in LFA SPF as well. When the value of vRtrMplsLspIgpShortcutLfaType is set to 'lfaOnly' the RSVP LSP is used as a LFA SPF and not used as igp-shortcut in regular SPF. An 'inconsistentValue' error is returned if an attempt is made to set this object to a non-default value when the value of the object vRtrMplsLspIgpShortcut is not set to 'true'. |
| TMN vRtrMplsLspIndex | 1.3.6.1.4.1.6527.3.1.2.6.1.1.1 | TmnxVRtrMplsLspID | accessible-for-notify | The unique value which identifies this Labeled Switch Path (LSP) for this virtual router in the Alcatel-Lucent SROS system. It is a unique value among entries with the same value of vRtrID. |
| U32 vRtrMplsLspInheritance | 1.3.6.1.4.1.6527.3.1.2.6.1.1.35 | Unsigned32 | read-create | For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrMplsGeneralTable, there is bit within vRtrMplsLspInheritance that controls whether to inherit the operational value of the object or use the administratively set value. Non mask bits will always have value of zero. This object is a bit-mask, with the following positions: vRtrMplsLspOptimizeTimer 0x1 vRtrMplsLspFRObject 0x2 vRtrMplsLspHoldTimer 0x4 vRtrMplsLspDestGlobalId 0x8 vRtrMplsLspDestTunnelNum 0x10 vRtrMplsLspFromNodeId 0x20 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsGeneralTable. |
| TIM vRtrMplsLspLastChange | 1.3.6.1.4.1.6527.3.1.2.6.1.1.3 | TimeStamp | read-only | The sysUpTime when this row was last modified. |
| NUM vRtrMplsLspLastPathChange | 1.3.6.1.4.1.6527.3.1.2.6.2.1.10 | TimeInterval | read-only | The time in 10-millisecond units since the last change occurred on this LSP. |
| NUM vRtrMplsLspLastTransition | 1.3.6.1.4.1.6527.3.1.2.6.2.1.8 | TimeInterval | read-only | The time in 10-millisecond units since the last transition occurred on this LSP. |
| T/F vRtrMplsLspLdpOverRsvpInclude | 1.3.6.1.4.1.6527.3.1.2.6.1.1.44 | TruthValue | read-create | The value of vRtrMplsLspLdpOverRsvpInclude specifies that this LSP can be included by IGP to calculate its SPF tree. The IGP (OSPF or ISIS) will subsequently provide LDP with all ECMP IGP next-hops and tunnel endpoints that it considers to be the lowest cost path to the destination. If an IGP calculation and an LDP over RSVP produce the same cost then LDP will always prefer an LDP over RSVP tunnel over an IGP route. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'. |
| T/F vRtrMplsLspLeastFill | 1.3.6.1.4.1.6527.3.1.2.6.1.1.45 | TruthValue | read-create | The value of vRtrMplsLspLeastFill specifies whether the use of the least-fill path selection method for the computation of the path of this LSP is enabled. By default, the path of an LSP is randomly chosen among a set of equal cost paths. |
| U32 vRtrMplsLspMainCTRetryLimit | 1.3.6.1.4.1.6527.3.1.2.6.1.1.47 | Unsigned32 | read-create | The value of vRtrMplsLspMainCTRetryLimit specifies the number of attempts the software should make before it can start using the backup class type. |
| U32 vRtrMplsLspMetric | 1.3.6.1.4.1.6527.3.1.2.6.1.1.13 | Unsigned32 | read-create | The value of vRtrMplsLspMetric specifies the metric for this LSP which is used to select an LSP among a set of LSPs which are destined to the same egress 7x50 router. The LSP with the lowest metric will be selected. In LDP-over-RSVP, LDP performs a lookup in the Routing Table Manager (RTM) which provides the next hop to the destination PE and the advertising router (ABR or destination PE itself). If the advertising router matches the targeted LDP peer, LDP then performs a second lookup for the advertising router in the Tunnel Table Manager (TTM). This lookup returns the best RSVP LSP to use to forward packets for an LDP FEC learned through the targeted LDP session. The lookup returns the LSP with the lowest metric. If multiple LSPs have the same metric, then the result of the lookup will be to select the first one available in the TTM. |
| TLN vRtrMplsLspName | 1.3.6.1.4.1.6527.3.1.2.6.1.1.4 | TLNamedItemOrEmpty | read-create | Administrative name for this Labeled Switch Path. The vRtrMplsLspName must be unique within a virtual router instance. When the value of the object vRtrMplsLspType is 'p2mpAuto', LSPs are auto-created dynamically by the system using LSP template values configured in the associated row entry of vRtrMplsLspTemplateTable. For auto-created LSPs, vRtrMplsLspName can have a maximum of 64 characters which consists of vRtrMplsLspTemplateName, vRtrID and MTTM(Multicast Tunnel Table Manager)Identifier. If vRtrMplsLspType is not 'p2mpAuto', vRtrMplsLspName can have a maximum of 32 characters. |
| U32 vRtrMplsLspNegotiatedMTU | 1.3.6.1.4.1.6527.3.1.2.6.1.1.27 | Unsigned32 | read-only | The value of vRtrMplsLspNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during LSP establishment. |
| INT vRtrMplsLspNotificationReasonCode | 1.3.6.1.4.1.6527.3.1.2.6.16.1 | INTEGER | accessible-for-notify | Used by vRtrMplsLspDown, the value indicates the reason for the LSP going down. |
| C64 vRtrMplsLspOctetsEx | 1.3.6.1.4.1.6527.3.1.2.6.2.1.1 | Counter64 | read-only | The number of octets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment. |
| MPL vRtrMplsLspOldTunnelIndex | 1.3.6.1.4.1.6527.3.1.2.6.16.14 | MplsTunnelIndex | accessible-for-notify | The value of vRtrMplsLspOldTunnelIndex indicates the tunnel index of of the old LSP path. |
| I32 vRtrMplsLspOperationalPaths | 1.3.6.1.4.1.6527.3.1.2.6.2.1.13 | Integer32 | read-only | The number of operational paths for this LSP. This includes the path currently active, as well as operational standby paths. |
| T/F vRtrMplsLspOperFastReroute | 1.3.6.1.4.1.6527.3.1.2.6.1.1.37 | TruthValue | read-only | The value of vRtrMplsLspOperFastReroute specifies whether the operational LSP has fast reroute enabled or disabled. When make-before-break functionality for the LSP is enabled and if the fast reroute setting is changed, the resources for the existing LSP will not be released until a new path with the new attribute settings has been established. While a new path is being signaled, the administrative value and the operational values of fast reroute setting for the LSP may differ. The value of vRtrMplsLspFastReroute specifies the setting used for the new LSP path trying to be established whereas the value of vRtrMplsLspOperFastReroute specifies the setting for the existing LSP path. |
| U32 vRtrMplsLspOperMetric | 1.3.6.1.4.1.6527.3.1.2.6.1.1.43 | Unsigned32 | read-only | The value of vRtrMplsLspOperMetric indicates the operational metric for the LSP. |
| TMN vRtrMplsLspOperState | 1.3.6.1.4.1.6527.3.1.2.6.1.1.6 | TmnxOperState | read-only | The current operational state of this LSP. |
| U32 vRtrMplsLspOptimizeTimer | 1.3.6.1.4.1.6527.3.1.2.6.1.1.36 | Unsigned32 | read-create | The value of vRtrMplsLspOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspOptimizeTimer bit in vRtrMplsLspInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsGeneralOptimizeTimer. |
| TNA vRtrMplsLspOriginTemplate | 1.3.6.1.4.1.6527.3.1.2.6.1.1.49 | TNamedItemOrEmpty | read-only | When the value of the vRtrMplsLspType is 'p2mpAuto', the value of vRtrMplsLspOriginTemplate indicates the LSP Template which was used to create this LSP. For all other types of LSPs, the value of vRtrMplsLspOriginTemplate is an empty string. |
| I32 vRtrMplsLspOutSegIndx | 1.3.6.1.4.1.6527.3.1.2.6.1.1.10 | Integer32 | read-create | The vRtrMplsLspOutSegIndx is the index value of the entry in the mplsOutSegmentTable associated with this vRtrMplsLspEntry when vRtrMplsLspType is 'static'. If vRtrMplsLspType is 'dynamic', the value of this object will be zero (0). |
| U32 vRtrMplsLspP2mpId | 1.3.6.1.4.1.6527.3.1.2.6.1.1.41 | Unsigned32 | read-create | The value of vRtrMplsLspP2mpId specifies a unique identifier known as point to multipoint (P2MP) identifier (ID). |
| C64 vRtrMplsLspPackets | 1.3.6.1.4.1.6527.3.1.2.6.2.1.2 | Counter64 | read-only | The number of packets that have been forwarded over current LSP active path. The number reported is not realtime, may be subject to several minutes delay. The delay is controllable by MPLS statistics gathering interval, which by default is once every 5 minutes. If MPLS statistics gathering is not enabled, this number will not increment. |
| INT vRtrMplsLspPathActiveByManual | 1.3.6.1.4.1.6527.3.1.2.6.4.1.63 | INTEGER | read-only | The value of vRtrMplsLspPathActiveByManual indicates whether a secondary standby path has become the active LSP path due to manual intervention. When vRtrMplsLspSwitchStbyPath is set to 'doAction' a manual switch is attempted. When vRtrMplsLspSwitchStbyPathForce is set to 'true' the manual switch is forced. When the value of vRtrMplsLspPathActiveByManual is set to 'notApplicable', the LSP path is active but not due to any manual intervention. When the value of vRtrMplsLspPathActiveByManual is set to 'noForce', the LSP path has become active by a manual switch specified by the user. When the value of vRtrMplsLspPathActiveByManual is set to 'force', the LSP path has become active by a forced manual switch executed by the user. |
| T/F vRtrMplsLspPathAdaptive | 1.3.6.1.4.1.6527.3.1.2.6.4.1.28 | TruthValue | read-create | Setting the value of vRtrMplsLspPathAdaptive to 'true', enables make-before-break functionality for the LSP path. Setting the value to 'false', disables make-before-break functionality for the path. When the vRtrMplsLspPathAdaptive bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdaptive. |
| U32 vRtrMplsLspPathAdminGroupExclude | 1.3.6.1.4.1.6527.3.1.2.6.4.1.27 | Unsigned32 | read-create | The value of vRtrMplsLspPathAdminGroupExclude is a bit-map that specifies a list of admin groups that should be excluded when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this LSP path. This implies that each link that this LSP path goes through must not be associated with any of the admin groups in the exclude list. When the vRtrMplsLspPathAdminGroupExclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupExclude. |
| U32 vRtrMplsLspPathAdminGroupInclude | 1.3.6.1.4.1.6527.3.1.2.6.4.1.26 | Unsigned32 | read-create | The value of vRtrMplsLspPathAdminGroupInclude is a bit-map that specifies a list of admin groups that should be included when this LSP path is setup. If bit 'n' is set, then the admin group with value 'n' is included for this LSP path. This implies that each link that this LSP path goes through must be associated with at least one of the admin groups in the include list. When the vRtrMplsLspPathAdminGroupInclude bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspAdminGroupInclude. |
| TMN vRtrMplsLspPathAdminState | 1.3.6.1.4.1.6527.3.1.2.6.4.1.17 | TmnxAdminState | read-create | The desired administrative state for this LSP path. |
| I32 vRtrMplsLspPathBackupCT | 1.3.6.1.4.1.6527.3.1.2.6.4.1.56 | Integer32 | read-create | The value of vRtrMplsLspPathBackupCT specifies the backup class type (CT) associated with the LSP. A value of -1 indicates that no backup class type has been configured for the LSP. |
| I32 vRtrMplsLspPathBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.4.1.6 | Integer32 | read-create | The value of vRtrMplsLspPathBandwidth specifies the amount of bandwidth in mega-bits per seconds (Mbps) to be reserved for this LSP path. A value of zero (0) indicates that no bandwidth is reserved. |
| T/F vRtrMplsLspPathBwProtect | 1.3.6.1.4.1.6527.3.1.2.6.4.1.7 | TruthValue | read-create | When vRtrMplsLspPathBwProtect has a value of 'true', bandwidth protection is enabled on a LSP. LSPs that reserve bandwidth will be used for EF services where customers need guaranteed bandwidth. It is expected that multiple EF services will be assigned to a single LSP. When bandwidth protection is enabled on an LSP, each time this LSP is used for a certain service the bandwidth allocated on that service is deducted from the bandwidth reserved for the LSP. Once the bandwidth is exhausted on the LSP, the ESR will provide feedback to the provider indicating that this LSP has exhausted its resources. |
| C32 vRtrMplsLspPathChanges | 1.3.6.1.4.1.6527.3.1.2.6.2.1.9 | Counter32 | read-only | The number of path changes this LSP has had. For every path change (path down, path up, path change), a corresponding syslog/trap (if enabled) is generated for it. |
| TNA vRtrMplsLspPathClassOfService | 1.3.6.1.4.1.6527.3.1.2.6.4.1.11 | TNamedItemOrEmpty | read-create | The name of the class of service value to be assigned to all packets on the LSP is specified with vRtrMplsLspPathClassOfService. The EXP bits in the MPLS header are set based on the global mapping table that specified the mapping between the forwarding class and the EXP bits. When class of service is specified, all packets will be marked with the same EXP bits that match the vRtrMplsLspPathClassOfService name in the mapping table. An empty string, ''H, specifies no class of service. Packets are assigned EXP bits based on the same mapping table, however each packet is marked with EXP bits based on the forwarding class from which it is serviced. |
| TMN vRtrMplsLspPathClassType | 1.3.6.1.4.1.6527.3.1.2.6.4.1.52 | TmnxRsvpDSTEClassType | read-create | The value of vRtrMplsLspPathClassType specifies the class type (CT) associated with this LSP path. When the vRtrMplsLspPathClassType bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspClassType. |
| U32 vRtrMplsLspPathCongChgPercent | 1.3.6.1.4.1.6527.3.1.2.6.16.8 | Unsigned32 | accessible-for-notify | The value of vRtrMplsLspPathCongChgPercent indicates the percentage change in congestion. |
| INT vRtrMplsLspPathCos | 1.3.6.1.4.1.6527.3.1.2.6.4.1.4 | INTEGER | read-create | The configured Class Of Service (COS) for this path. If the value is between 0 and 7 inclusive, this value will be inserted in the 3 bit COS field in the label. If the value is 255, the value in the COS field of the label will depend on other factors. |
| T/F vRtrMplsLspPathCosSource | 1.3.6.1.4.1.6527.3.1.2.6.4.1.10 | TruthValue | read-create | When vRtrMplsLspPathCosSource is set to 'true', the value of vRtrMplsLspPathClassOfService overrides vRtrMplsLspClassOfService. When 'false', the value of vRtrMplsLspClassOfService is used. |
| C32 vRtrMplsLspPathCspfQueries | 1.3.6.1.4.1.6527.3.1.2.6.5.1.5 | Counter32 | read-only | The value of vRtrMplsLspPathCspfQueries specifies the number of CSPF queries that have been made for this LSP path. |
| NTF vRtrMplsLspPathDown | 1.3.6.1.4.1.6527.3.1.3.6.0.6 | This Notification is generated when a LSP Path transitions out of 'inService' state to any other state. | ||
| vRtrMplsLspPathEntry | 1.3.6.1.4.1.6527.3.1.2.6.4.1 | not-accessible | Each row entry represents an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries in this table can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsLspPathType to have been assigned a valid value. | |
| TMN vRtrMplsLspPathFailCode | 1.3.6.1.4.1.6527.3.1.2.6.4.1.24 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsLspPathFailCode specifies the reason code for LSP Path failure. A value of 0 indicates that no failure has occurred. |
| IP vRtrMplsLspPathFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.4.1.25 | IpAddress | read-only | The value of vRtrMplsLspPathFailNodeAddr specifies the IP address of the node in the LSP path at which the LSP path failed. When no failure has occurred, this value is 0. |
| U32 vRtrMplsLspPathHoldPriority | 1.3.6.1.4.1.6527.3.1.2.6.4.1.13 | Unsigned32 | read-create | The value of vRtrMplsLspPathHoldPriority specifies the hold priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. |
| U32 vRtrMplsLspPathHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.4.1.15 | Unsigned32 | read-create | The value of vRtrMplsLspPathHopLimit specifies the maximum number of hops that a LSP will traverse including the ingress and egress ESRs. A LSP will not be setup if the hop limit is exceeded. When the vRtrMplsLspPathHopLimit bit in vRtrMplsLspPathInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit. |
| U32 vRtrMplsLspPathInheritance | 1.3.6.1.4.1.6527.3.1.2.6.4.1.19 | Unsigned32 | read-create | For each writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrMplsLspTable, controls whether to inherit the operational value of that object, or use the administratively set value. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrMplsLspPathHopLimit 0x2000 vRtrMplsLspPathAdminGroupInclude 0x20000 vRtrMplsLspPathAdminGroupExclude 0x40000 vRtrMplsLspPathAdaptive 0x80000 vRtrMplsLspPathOptimizeTimer 0x100000 vRtrMplsLspPathClassType 0x1000000 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. The corresponding mask bit will be changed to one when SNMP SET is performed on any of the inherited objects (vRtrMplsLspPathHopLimit, vRtrMplsLspPathAdminGroupInclude, etc). When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsLspTable. |
| T/F vRtrMplsLspPathIsFastRetry | 1.3.6.1.4.1.6527.3.1.2.6.4.1.55 | TruthValue | read-only | The value of vRtrMplsLspPathIsFastRetry indicates which retry timer is being referred to by vRtrMplsLspPathRetryTimeRemaining. When the value of vRtrMplsLspPathIsFastRetry is set to 'true', vRtrMplsLspPathRetryTimeRemaining is referring to either the P2P active path fast timer, vRtrMplsGenP2pActPathFastRetry or the secondary fast retry timer, vRtrMplsGeneralSecFastRetryTimer. When the value of vRtrMplsLspPathIsFastRetry is set to 'false', vRtrMplsLspPathRetryTimeRemaining is referring to the LSP retry timer, vRtrMplsLspRetryTimer. |
| TIM vRtrMplsLspPathLastChange | 1.3.6.1.4.1.6527.3.1.2.6.4.1.2 | TimeStamp | read-only | The sysUpTime when this row was last modified. |
| TIM vRtrMplsLspPathLastMBBEnd | 1.3.6.1.4.1.6527.3.1.2.6.4.1.42 | TimeStamp | read-only | The value of vRtrMplsLspPathLastMBBEnd indicates the sysUpTime when the last MBB ended. |
| U32 vRtrMplsLspPathLastMBBMetric | 1.3.6.1.4.1.6527.3.1.2.6.4.1.43 | Unsigned32 | read-only | The value of vRtrMplsLspPathLastMBBMetric indicates the cost of the traffic engineered path for the LSP path prior to MBB. |
| INT vRtrMplsLspPathLastMBBState | 1.3.6.1.4.1.6527.3.1.2.6.4.1.44 | INTEGER | read-only | The value of vRtrMplsLspPathLastMBBState specifies whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed. |
| TMN vRtrMplsLspPathLastMBBType | 1.3.6.1.4.1.6527.3.1.2.6.4.1.41 | TmnxMplsMBBType | read-only | The value of vRtrMplsLspPathLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted. |
| TIM vRtrMplsLspPathLastResigAttempt | 1.3.6.1.4.1.6527.3.1.2.6.4.1.39 | TimeStamp | read-only | The value of vRtrMplsLspPathLastResigAttempt indicates the sysUpTime when the last attempt to resignal this LSP was made. |
| MPL vRtrMplsLspPathLspId | 1.3.6.1.4.1.6527.3.1.2.6.4.1.20 | MplsLSPID | read-only | This value identifies the label switched path that is signaled for this entry. |
| NTF vRtrMplsLspPathLstFillReoptElig | 1.3.6.1.4.1.6527.3.1.3.6.0.16 | The vRtrMplsLspPathLstFillReoptElig notification is generated when a timer based re-signal found a path with the same cost but which has a better least-fill metric. | ||
| U32 vRtrMplsLspPathMainCTRetryRem | 1.3.6.1.4.1.6527.3.1.2.6.4.1.57 | Unsigned32 | read-only | The value of vRtrMplsLspPathMainCTRetryRem specifies the number of remaining attempts the software should make before it can start using the backup class type for the LSP. |
| TMN vRtrMplsLspPathMBBFailCode | 1.3.6.1.4.1.6527.3.1.2.6.4.1.49 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsLspPathMBBFailCode specifies the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred. |
| IP vRtrMplsLspPathMBBFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.4.1.51 | InetAddress | read-only | The value of vRtrMplsLspPathMBBFailNodeAddr specifies the IP address of the node in the LSP path at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsLspPathMBBFailNodeArType and empty string for vRtrMplsLspPathMBBFailNodeAddr indicates that no failure has occurred. |
| IPt vRtrMplsLspPathMBBFailNodeArType | 1.3.6.1.4.1.6527.3.1.2.6.4.1.50 | InetAddressType | read-only | The value of vRtrMplsLspPathMBBFailNodeArType indicates the type of vRtrMplsLspPathMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred. |
| U32 vRtrMplsLspPathMBBMainCTRetryRem | 1.3.6.1.4.1.6527.3.1.2.6.4.1.60 | Unsigned32 | read-only | The value of vRtrMplsLspPathMBBMainCTRetryRem indicates the number of remaining attempts the software should make before it can start using the backup class type for the LSP. |
| U32 vRtrMplsLspPathMBBNextRetry | 1.3.6.1.4.1.6527.3.1.2.6.4.1.47 | Unsigned32 | read-only | The value of vRtrMplsLspPathMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB. |
| INT vRtrMplsLspPathMbbReasonCode | 1.3.6.1.4.1.6527.3.1.2.6.16.10 | INTEGER | accessible-for-notify | The value of vRtrMplsLspPathMbbReasonCode indicates the reason code for the make-before-break (MBB) operation of the LSP path. It indicates whether the operation is failed, aborted or ignored. |
| U32 vRtrMplsLspPathMBBRetryAttempts | 1.3.6.1.4.1.6527.3.1.2.6.4.1.48 | Unsigned32 | read-only | The value of vRtrMplsLspPathMBBRetryAttempts indicates 'n' where nth attempt for the MBB is in progress. |
| TIM vRtrMplsLspPathMBBStarted | 1.3.6.1.4.1.6527.3.1.2.6.4.1.46 | TimeStamp | read-only | The value of vRtrMplsLspPathMBBStarted indicates the sysUpTime when the in-progress MBB started. |
| INT vRtrMplsLspPathMBBState | 1.3.6.1.4.1.6527.3.1.2.6.4.1.32 | INTEGER | read-only | The value of vRtrMplsLspPathMBBState specifies the state of the most recent invocation of the make-before-break functionality. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful inProgress (3) - make-before-break in progress fail (4) - make-before-break failed. This object was made obsolete in release 6.0 R4 and replaced with vRtrMplsLspPathLastMBBState. |
| INT vRtrMplsLspPathMbbStatus | 1.3.6.1.4.1.6527.3.1.2.6.16.9 | INTEGER | accessible-for-notify | The value of vRtrMplsLspPathMbbStatus indicates the status of the make-before-break (MBB) operation for the LSP path. |
| NTF vRtrMplsLspPathMbbStatusEvent | 1.3.6.1.4.1.6527.3.1.3.6.0.19 | The vRtrMplsLspPathMbbStatusEvent notification is generated to report the status of the make-before-break(MBB) operation for the LSP path. | ||
| U32 vRtrMplsLspPathMBBTimeoutIn | 1.3.6.1.4.1.6527.3.1.2.6.4.1.65 | Unsigned32 | read-only | The value of vRtrMplsLspPathMBBTimeoutIn specifies the amount of time remaining, in seconds, for the in-progress MBB path state to time out after the initial PATH message has been sent. If the timer expires and the in-progress MBB path has not become operationally up, the MBB path is torn down and the retry timer is started to schedule a new retry cycle. |
| TMN vRtrMplsLspPathMBBTypeInProg | 1.3.6.1.4.1.6527.3.1.2.6.4.1.45 | TmnxMplsMBBType | read-only | The value of vRtrMplsLspPathMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress. |
| U32 vRtrMplsLspPathMetric | 1.3.6.1.4.1.6527.3.1.2.6.4.1.40 | Unsigned32 | read-only | The value of vRtrMplsLspPathMetric indicates the cost of the traffic engineered path returned by the IGP. |
| U32 vRtrMplsLspPathNegotiatedMTU | 1.3.6.1.4.1.6527.3.1.2.6.4.1.23 | Unsigned32 | read-only | The value of vRtrMplsLspPathNegotiatedMTU specifies the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this LSP Path. |
| MPL vRtrMplsLspPathNewPathIndex | 1.3.6.1.4.1.6527.3.1.2.6.4.1.59 | MplsTunnelIndex | read-create | The value of vRtrMplsLspPathNewPathIndex specifies the index for the new path in mplsTunnelTable. |
| U32 vRtrMplsLspPathNextOptimize | 1.3.6.1.4.1.6527.3.1.2.6.4.1.30 | Unsigned32 | read-only | The value of vRtrMplsLspPathNextOptimize specifies the current value of the optimize timer. This is the time, in seconds, remaining till the optimize timer will expire and optimization will be started for the LSP path. |
| TMN vRtrMplsLspPathNotificationReasonCode | 1.3.6.1.4.1.6527.3.1.2.6.16.2 | TmnxMplsLspFailCode | accessible-for-notify | Used by vRtrMplsLspPathDown, the value indicates the reason for the LSP path going down. |
| U32 vRtrMplsLspPathOperAdminGrExcld | 1.3.6.1.4.1.6527.3.1.2.6.44.1.7 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperAdminGrExcld is a bit-map which specifies a list of admin groups excluded by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the list of excluded admin groups is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of either vRtrMplsLspAdminGroupExclude or vRtrMplsLspPathAdminGroupExclude specifies the exclude admin groups bit-map for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperAdminGrExcld specifies the exclude admin groups bit-map for the existing LSP path. |
| U32 vRtrMplsLspPathOperAdminGrpIncl | 1.3.6.1.4.1.6527.3.1.2.6.44.1.6 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperAdminGrpIncl is a bit-map which specifies a list of admin groups included by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the list of included admin groups is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of either vRtrMplsLspAdminGroupInclude or vRtrMplsLspPathAdminGroupInclude specifies the include admin groups bit-map for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperAdminGrpIncl specifies the include admin groups bit-map for the existing LSP path. |
| I32 vRtrMplsLspPathOperBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.4.1.31 | Integer32 | read-only | The value of vRtrMplsLspPathOperBandwidth specifies the amount of bandwidth in mega-bits per seconds (Mbps) that has been reserved for the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path bandwidth is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new bandwidth settings has been established. While a new path is being signaled, the administrative value and the operational values of the path bandwidth may differ. The value of vRtrMplsLspPathBandwidth specifies the bandwidth requirements for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperBandwidth specifies the bandwidth reserved for the existing LSP path. |
| T/F vRtrMplsLspPathOperCspf | 1.3.6.1.4.1.6527.3.1.2.6.44.1.8 | TruthValue | read-only | The value of vRtrMplsLspPathOperCspf specifies whether the currently operational LSP path has used CSPF computation for constrained-path enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP CSPF setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspCspf specifies the CSPF setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperCspf specifies the CSPF setting for the existing LSP path. |
| T/F vRtrMplsLspPathOperCspfToFrstLs | 1.3.6.1.4.1.6527.3.1.2.6.44.1.9 | TruthValue | read-only | The value of vRtrMplsLspPathOperCspfToFrstLs specifies whether the currently operational LSP path had CSPF to first loose hop enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP CSPF to First Loose Hop setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspCspfToFirstLoose specifies the CSPF to First Loose Hop setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperCspfToFrstLs specifies the CSPF to First Loose Hop setting for the existing LSP path. |
| I32 vRtrMplsLspPathOperCT | 1.3.6.1.4.1.6527.3.1.2.6.4.1.58 | Integer32 | read-only | The value of vRtrMplsLspMainCTRetryLimit specifies operational class type (CT) associated with the LSP. A value of -1 indicates that no operational class type has been configured for the LSP |
| vRtrMplsLspPathOperEntry | 1.3.6.1.4.1.6527.3.1.2.6.44.1 | not-accessible | Each row entry represents an operational status for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries cannot be created and deleted via SNMP SET operations. A row entry will have valid operational status info when vRtrMplsLspPathOperState is set to inService. | |
| U32 vRtrMplsLspPathOperFRHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.44.1.14 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperFRHopLimit indicates the total number of hops to be used by detour LSP before merging to currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the LSP FR Hop Limit setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspFRHopLimit specifies the FR Hop Limit setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperFRHopLimit specifies the FR Hop Limit setting for the existing LSP path. |
| T/F vRtrMplsLspPathOperFRNodeProtect | 1.3.6.1.4.1.6527.3.1.2.6.44.1.12 | TruthValue | read-only | The value of vRtrMplsLspPathOperFRNodeProtect specifies whether the currently operational LSP path has node protection enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP node protection setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspFRNodeProtect specifies the node protection setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperFRNodeProtect specifies the node protection setting for the existing LSP path. |
| U32 vRtrMplsLspPathOperHoldPriority | 1.3.6.1.4.1.6527.3.1.2.6.44.1.2 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperHoldPriority specifies the hold priority used by the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path hold priority is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new hold priority settings has been established. While a new path is being signaled, the administrative value and the operational values of the path hold priority may differ. The value of vRtrMplsLspPathHoldPriority specifies the hold priority for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperHoldPriority specifies the hold priority for the existing LSP path. |
| U32 vRtrMplsLspPathOperHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.44.1.5 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperHopLimit specifies the maximum hops limit used by the currently operational LSP path. When make-before-break functionality for the LSP is enabled and if the hop limit is changed at either LSP or LSP path level, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path hop limit may differ. The value of either vRtrMplsLspHopLimit or vRtrMplsLspPathHopLimit specifies the hop limit for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperHopLimit specifies the hop limit for the existing LSP path. |
| T/F vRtrMplsLspPathOperLeastFill | 1.3.6.1.4.1.6527.3.1.2.6.44.1.10 | TruthValue | read-only | The value of vRtrMplsLspPathOperLeastFill specifies whether the currently operational LSP path was computed with the least-fill path selection method. When make-before-break functionality for the LSP is enabled and if the LSP least-fill setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspLeastFill specifies the least-fill setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperLeastFill specifies the least-fill setting for the existing LSP path. |
| U32 vRtrMplsLspPathOperMetric | 1.3.6.1.4.1.6527.3.1.2.6.4.1.53 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperMetric indicates the operational metric for the LSP path. |
| U32 vRtrMplsLspPathOperMTU | 1.3.6.1.4.1.6527.3.1.2.6.4.1.35 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperMTU specifies the size for the Maximum transmission unit (MTU) that is currently operation for this LSP Path. |
| T/F vRtrMplsLspPathOperPropAdminGrp | 1.3.6.1.4.1.6527.3.1.2.6.44.1.13 | TruthValue | read-only | The value of vRtrMplsLspPathOperPropAdminGrp specifies whether the currently operational LSP path has propagation admin-groups enabled or disabled. When make-before-break functionality for the LSP is enabled and if the LSP propagate admin groups setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspPropAdminGroup specifies the propagate admin groups setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperPropAdminGrp specifies the propagate admin groups setting for the existing LSP path. |
| INT vRtrMplsLspPathOperRecord | 1.3.6.1.4.1.6527.3.1.2.6.44.1.3 | INTEGER | read-only | The value of vRtrMplsLspPathOperRecord specifies whether the operational LSP path is recording or not recording all the traversed hops. When make-before-break functionality for the LSP is enabled and if the path hops recording setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of hops recording setting of the path may differ. The value of vRtrMplsLspPathRecord specifies the hops recording setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRecord specifies the hops recording setting for the existing LSP path. |
| INT vRtrMplsLspPathOperRecordLabel | 1.3.6.1.4.1.6527.3.1.2.6.44.1.4 | INTEGER | read-only | The value of vRtrMplsLspPathOperRecordLabel specifies whether the currently operational LSP path is recording or not recording the label allocated at each traversed node. When make-before-break functionality for the LSP is enabled and if the path label recording setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of label recording setting of the path may differ. The value of vRtrMplsLspPathRecordLabel specifies the label recording setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRecordLabel specifies the label recording setting for the existing LSP path. |
| T/F vRtrMplsLspPathOperRsvpAdspec | 1.3.6.1.4.1.6527.3.1.2.6.44.1.11 | TruthValue | read-only | The value of vRtrMplsLspPathOperRsvpAdspec specifies whether the currently operational LSP path has ADSPEC object included in RSVP messages or not. When make-before-break functionality for the LSP is enabled and if the LSP adspec setting is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new settings has been established. While a new path is being signaled, the administrative value and the operational values of the path may differ. The value of vRtrMplsLspRsvpAdspec specifies the adspec setting for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperRsvpAdspec specifies the adspec setting for the existing LSP path. |
| U32 vRtrMplsLspPathOperSetupPriority | 1.3.6.1.4.1.6527.3.1.2.6.44.1.1 | Unsigned32 | read-only | The value of vRtrMplsLspPathOperSetupPriority specifies the setup priority used by the operational LSP path. When make-before-break functionality for the LSP is enabled and if the path setup priority is changed, the resources allocated to the existing LSP paths will not be released until a new path with the new setup priority settings has been established. While a new path is being signaled, the administrative value and the operational values of the path setup priority may differ. The value of vRtrMplsLspPathSetupPriority specifies the setup priority for the new LSP path trying to be established whereas the value of vRtrMplsLspPathOperSetupPriority specifies the setup priority for the existing LSP path. |
| TMN vRtrMplsLspPathOperState | 1.3.6.1.4.1.6527.3.1.2.6.4.1.18 | TmnxOperState | read-only | The current operational state of this LSP path. |
| vRtrMplsLspPathOperTable | 1.3.6.1.4.1.6527.3.1.2.6.44 | not-accessible | The vRtrMplsLspPathOperTable has an entry for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. | |
| U32 vRtrMplsLspPathOptimizeTimer | 1.3.6.1.4.1.6527.3.1.2.6.4.1.29 | Unsigned32 | read-create | The value of vRtrMplsLspPathOptimizeTimer specifies the time, in seconds, the software will wait before attempting to re-optimize the LSP path. When CSPF is enabled, changes in the network topology may cause the existing path of a loose-hop LSP to become sub-optimal. Such LSPs can be re-optimized and re-routed through more optimal paths by recalculating the path for the LSP at periodic intervals. This interval is controlled by the optimize timer. A value of 0 indicates that optimization has been disabled. When the vRtrMplsLspPathOptimizeTimer bit in vRtrMplsLspPathInheritance is cleared (0), the value returned in the GET request is inherited from vRtrMplsLspOptimizeTimer. |
| INT vRtrMplsLspPathPreference | 1.3.6.1.4.1.6527.3.1.2.6.4.1.9 | INTEGER | read-create | When there is no path in the LSP with vRtrMplsLspPathType value of 'primary', 'secondary' type paths of this LSP with the same value of vRtrMplsLspPathPreference are used for load sharing. When a 'primary' type path exists in the LSP, vRtrMplsLspPathPreference is used to denote at which priority one 'secondary' path will supercede another when the 'primary' fails. 1 indicates the highest priority value. For LSP with vRtrMplsLspPathType value of 'standby' type paths the value of vRtrMplsLspPathPreference is in the range of (1..255). For path type 'primary' the value of vRtrMplsLspPathPreference is set to 0. For path type 'secondary' the value of vRtrMplsLspPathPreference is set to 255. |
| BIT vRtrMplsLspPathProperties | 1.3.6.1.4.1.6527.3.1.2.6.4.1.5 | Bits | read-only | The set of configured properties for this path expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value 1 is set. |
| INT vRtrMplsLspPathRecord | 1.3.6.1.4.1.6527.3.1.2.6.4.1.14 | INTEGER | read-create | When the value of vRtrMplsLspPathRecord is 'record', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecord is 'noRecord', recording of all the hops that a LSP traverses is disabled. |
| INT vRtrMplsLspPathRecordLabel | 1.3.6.1.4.1.6527.3.1.2.6.4.1.36 | INTEGER | read-create | When the value of vRtrMplsLspPathRecordLabel is 'record', recording of labels at each node that a LSP traverses is enabled. When the value of vRtrMplsLspPathRecordLabel is 'noRecord', recording of labels at each node that a LSP traverses is disabled. |
| NTF vRtrMplsLspPathRerouted | 1.3.6.1.4.1.6527.3.1.3.6.0.7 | The vRtrMplsLspPathRerouted notification is generated when an LSP Path is rerouted. | ||
| TMN vRtrMplsLspPathResignal | 1.3.6.1.4.1.6527.3.1.2.6.4.1.33 | TmnxActionType | read-create | Setting the value of vRtrMplsLspPathResignal to 'doAction' triggers the re-signaling of the LSP path. If the LSP path is operationally down either due to network failure or due to the retry attempts count being exceeded, setting this variable to 'doAction' will initiate the signaling for the path. A make-before-break signaling for the path will be initiated if the LSP is operationally up but the make-before-break retry attempts count was exceeded. Make-before-break signaling will also be initiated for any LSP that is operationally up. This may be used to cause a loose-hop LSP to be optimized. If a re-signal is triggered while a re-signaling is already in progress, the old transient state will be destroyed and a new transaction being triggered. An SNMP GET request on this object should return 'notApplicable'. |
| NTF vRtrMplsLspPathResignaled | 1.3.6.1.4.1.6527.3.1.3.6.0.8 | The vRtrMplsLspPathResignaled notification is generated when an LSP Path is resignaled. The vRtrMplsLspPathLastMBBType indicates the reason why the LSP Path was resignaled. | ||
| T/F vRtrMplsLspPathResignalEligible | 1.3.6.1.4.1.6527.3.1.2.6.4.1.54 | TruthValue | read-only | The value of vRtrMplsLspPathResignalEligible indicates that the LSP path is eligible for re-signaling on the basis of available bandwidth. |
| U32 vRtrMplsLspPathRetryAttempts | 1.3.6.1.4.1.6527.3.1.2.6.5.1.3 | Unsigned32 | read-only | The number of unsuccessful attempts which have been made to signal this path. As soon as the path gets signalled, this is set to 0. |
| U32 vRtrMplsLspPathRetryTimeRemaining | 1.3.6.1.4.1.6527.3.1.2.6.4.1.21 | Unsigned32 | read-only | The time in 10-millisecond units to signal this path. |
| ROW vRtrMplsLspPathRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.4.1.1 | RowStatus | read-create | The row status used for creation, deletion, or control of vRtrMplsLspPathTable entries. Before the row can be placed into the 'active' state vRtrMplsLspPathType must have been assigned a valid value. |
| U32 vRtrMplsLspPathSetupPriority | 1.3.6.1.4.1.6527.3.1.2.6.4.1.12 | Unsigned32 | read-create | The value of vRtrMplsLspPathSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. |
| T/F vRtrMplsLspPathSharing | 1.3.6.1.4.1.6527.3.1.2.6.4.1.16 | TruthValue | read-create | When vRtrMplsLspPathSharing has a value of 'true', path-sharing is enabled for the secondary path. Path-sharing is used to control the hops of the secondary path. When vRtrMplsLspPathSharing have a value of 'false', CSPF attempts to find a path for the secondary that does not include any node or link that is common to the active primary path. This variable is valid only if vRtrMplsLspPathType is set to 'secondary'. |
| U32 vRtrMplsLspPathSigBWLastMBB | 1.3.6.1.4.1.6527.3.1.2.6.4.1.62 | Unsigned32 | read-only | The value of vRtrMplsLspPathSigBWLastMBB indicates the bandwidth used to signal the last MBB that occurred. |
| U32 vRtrMplsLspPathSigBWMBBInProg | 1.3.6.1.4.1.6527.3.1.2.6.4.1.61 | Unsigned32 | read-only | The value of vRtrMplsLspPathSigBWMBBInProg indicates the bandwidth used to signal the MBB currently in progress. |
| NTF vRtrMplsLspPathSoftPreempted | 1.3.6.1.4.1.6527.3.1.3.6.0.15 | The vRtrMplsLspPathSoftPreempted notification is generated when an LSP Path is soft-preempted. | ||
| T/F vRtrMplsLspPathSrlg | 1.3.6.1.4.1.6527.3.1.2.6.4.1.37 | TruthValue | read-create | The value of vRtrMplsLspPathSrlg specifies whether the use of SRLG constraint in the computation of a secondary path for an LSP at the head-end Label Edge Router (LER) is enabled. The value vRtrMplsLspPathSrlg is used only when the value of vRtrMplsLspPathType is 'secondary'. When the value of vRtrMplsLspPathSrlg is true, the use of SRLG constraint in the computation of a secondary path is enabled. |
| T/F vRtrMplsLspPathSrlgDisjoint | 1.3.6.1.4.1.6527.3.1.2.6.4.1.38 | TruthValue | read-only | The value of vRtrMplsLspPathSrlgDisjoint specifies whether the relevant standby lsp path is SRLG disjoint from the associated primary lsp path for an LSP at the head-end Label Edge Router (LER). The value vRtrMplsLspPathSrlgDisjoint is used only when the value of vRtrMplsLspPathType is 'standby'. When the value of vRtrMplsLspPathSrlgDisjoint is 'true', primary and standby lsp path do not have SRLG membership in common. When the value of vRtrMplsLspPathSrlgDisjoint is 'false', primary and standby lsp path have SRLG membership in common. |
| INT vRtrMplsLspPathState | 1.3.6.1.4.1.6527.3.1.2.6.4.1.8 | INTEGER | read-only | The current working state of this path within this LSP. |
| vRtrMplsLspPathStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.5.1 | not-accessible | Each row entry represents a collection of statistics for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. Entries cannot be created and deleted via SNMP SET operations. | |
| vRtrMplsLspPathStatTable | 1.3.6.1.4.1.6527.3.1.2.6.5 | not-accessible | The vRtrMplsLspPathStatTable has an entry for an association between a Labeled Switch Path (LSP) in the vRtrMplsLspTable and a path (or tunnel) entry in the mplsTunnelTable. | |
| vRtrMplsLspPathTable | 1.3.6.1.4.1.6527.3.1.2.6.4 | not-accessible | The vRtrMplsLspPathTable provides an association between an LSP and a path. An LSP can have more than one path association, but only one of those paths can be specified as the primary path type. Paths are defined in as Tunnel entries in the mplsTunnelTable in the MPLS-TE-MIB. | |
| TES vRtrMplsLspPathTableSpinlock | 1.3.6.1.4.1.6527.3.1.2.6.3 | TestAndIncr | read-write | voluntary serialization control for vRtrMplsLspPathTable. Primarily used by SNMP manager to coordinate changes to vRtrMplsLspPathInheritance. |
| NUM vRtrMplsLspPathTimeDown | 1.3.6.1.4.1.6527.3.1.2.6.5.1.2 | TimeInterval | read-only | The total time in 10-millisecond units that this LSP Path has not been operational. |
| U32 vRtrMplsLspPathTimeoutIn | 1.3.6.1.4.1.6527.3.1.2.6.4.1.64 | Unsigned32 | read-only | The value of vRtrMplsLspPathTimeoutIn specifies the amount of time remaining, in seconds, for the LSP path state to time out after the initial PATH message has been sent. If the timer expires and the LSP path has not become operationally up, the LSP path is torn down and the retry timer is started to schedule a new retry cycle. |
| NUM vRtrMplsLspPathTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.5.1.1 | TimeInterval | read-only | The total time in 10-millisecond units that this LSP path has been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspPathTimeUp/vRtrMplsLspAge * 100 %). |
| C32 vRtrMplsLspPathTransitionCount | 1.3.6.1.4.1.6527.3.1.2.6.5.1.4 | Counter32 | read-only | The object vRtrMplsLspPathTransitionCount maintains the number of transitions that have occurred for this LSP. |
| I32 vRtrMplsLspPathTunnelARHopListIndex | 1.3.6.1.4.1.6527.3.1.2.6.4.1.22 | Integer32 | read-only | Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list. A value of 0 implies that there is no recored hop list associated with this LSP path. |
| I32 vRtrMplsLspPathTunnelCRHopListIndex | 1.3.6.1.4.1.6527.3.1.2.6.4.1.34 | Integer32 | read-only | Primary index into the vRtrMplsTunnelCHopTable identifying a particular computed hop list. A value of 0 implies that there is no computed hop list associated with this LSP path. |
| INT vRtrMplsLspPathType | 1.3.6.1.4.1.6527.3.1.2.6.4.1.3 | INTEGER | read-create | This variable is an enum that represents the role this path is taking within this LSP. |
| NTF vRtrMplsLspPathUp | 1.3.6.1.4.1.6527.3.1.3.6.0.5 | This Notification is generated when a LSP Path transitions to the 'inService' state from any other state. | ||
| U32 vRtrMplsLspPreference | 1.3.6.1.4.1.6527.3.1.2.6.1.1.23 | Unsigned32 | read-create | The value of vRtrMplsLspPreference specifies the preference for the LSP. This value is used for load balancing between multiple LSPs that exist between the same ingress and egress routers. By default, traffic is load balanced among the LSPs, since all LSPs have the same preference. To prefer one LSP over another, change the preference value for that LSP. The LSP with the lowest preference is used. |
| NUM vRtrMplsLspPrimaryTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.2.1.6 | TimeInterval | read-only | The total time in 10-millisecond units that this LSP's primary path has been operational. For example, the percentage contribution of the primary path to the operational time is given by (vRtrMplsLspPrimaryTimeUp/vRtrMplsLspTimeUp * 100) %. |
| T/F vRtrMplsLspPropAdminGroup | 1.3.6.1.4.1.6527.3.1.2.6.1.1.52 | TruthValue | read-create | The value of the vRtrMplsLspPropAdminGroup specifies whether the propagation of session attribute object with resource affinity (C-type 1) in PATH message is enabled. By default, the value of vRtrMplsLspPropAdminGroup is 'false' which specifies the session attribute object without resource affinity (C-Type 7) is propagated in PATH message and the admin-groups are ignored on Label Switched Router(LSR) while doing CSPF calculation. |
| T/F vRtrMplsLspRecord | 1.3.6.1.4.1.6527.3.1.2.6.1.1.22 | TruthValue | read-create | When the value of vRtrMplsLspRecord is 'true', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspRecord is 'false, recording of all the hops that a LSP traverses is disabled. |
| U32 vRtrMplsLspRetryLimit | 1.3.6.1.4.1.6527.3.1.2.6.1.1.12 | Unsigned32 | read-create | The value of vRtrMplsLspRetryLimit specifies the number of attempts the software should make to reestablish a failed LSP before the LSP is disabled. A value of 0 indicates that an infinite number of retry attempts should be made. |
| U32 vRtrMplsLspRetryTimer | 1.3.6.1.4.1.6527.3.1.2.6.1.1.11 | Unsigned32 | read-create | The value of vRtrMplsLspRetryTimer specifies the time in seconds the software will wait before attempting the establish the failed LSP. |
| ROW vRtrMplsLspRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.1.1.2 | RowStatus | read-create | The row status used for creation, deletion, or control of vRtrMplsLspTable entries. Before the row can be placed into the 'active' state vRtrMplsLspName must have been assigned a valid value. |
| T/F vRtrMplsLspRsvpAdspec | 1.3.6.1.4.1.6527.3.1.2.6.1.1.29 | TruthValue | read-create | When the value of vRtrMplsLspRsvpAdspec is 'true', the ADSPEC object will be included in RSVP messages. When the value of vRtrMplsLspRsvpAdspec is 'false', the ADSPEC object will not be included in RSVP messages. |
| INT vRtrMplsLspRsvpResvStyle | 1.3.6.1.4.1.6527.3.1.2.6.1.1.28 | INTEGER | read-create | The value of vRtrMplsLspRsvpResvStyle specifies the reservation style for RSVP. The reservation style can be set to 'Shared- Explicit' (se) or 'Fixed-Filter' (ff). |
| U32 vRtrMplsLspSetupPriority | 1.3.6.1.4.1.6527.3.1.2.6.1.1.20 | Unsigned32 | read-create | The value of vRtrMplsLspSetupPriority specifies the setup priority to use when insufficient bandwidth is available to setup a LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the value of vRtrMplsLspPathSetupPriority is set to '-1', the value of vRtrMplsLspSetupPriority is applied to that specific LSP/path. |
| I32 vRtrMplsLspStandbyPaths | 1.3.6.1.4.1.6527.3.1.2.6.2.1.12 | Integer32 | read-only | The number of standby paths configured for this LSP. |
| vRtrMplsLspStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.2.1 | not-accessible | Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations. | |
| vRtrMplsLspStatisticsEntry | 1.3.6.1.4.1.6527.3.1.2.6.39.1 | not-accessible | Each row entry represents a collection of statistics for a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations. | |
| vRtrMplsLspStatisticsTable | 1.3.6.1.4.1.6527.3.1.2.6.39 | not-accessible | The vRtrMplsLspStatisticsTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| U32 vRtrMplsLspStatsAccntingPolicy | 1.3.6.1.4.1.6527.3.1.2.6.38.1.8 | Unsigned32 | read-create | The value of vRtrMplsLspStatsAccntingPolicy specifies the accounting policy to be used for this entry. A value of zero indicates that the default accounting policy should be used. |
| TMN vRtrMplsLspStatsAdminState | 1.3.6.1.4.1.6527.3.1.2.6.38.1.9 | TmnxAdminState | read-create | The value of vRtrMplsLspStatsAdminState specifies whether egress statistics are enabled for this lsp. |
| T/F vRtrMplsLspStatsCollectStats | 1.3.6.1.4.1.6527.3.1.2.6.38.1.7 | TruthValue | read-create | The value of vRtrMplsLspStatsCollectStats specifies whether to collect statistics for this prefix. |
| vRtrMplsLspStatsEntry | 1.3.6.1.4.1.6527.3.1.2.6.38.1 | not-accessible | A row in this table represents information about the Statistics collection per MPLS LSP. | |
| TIM vRtrMplsLspStatsLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.38.1.6 | TimeStamp | read-only | The value of vRtrMplsLspStatsLastChanged indicates the time stamp of the last change to this row of this table. |
| TNA vRtrMplsLspStatsLspName | 1.3.6.1.4.1.6527.3.1.2.6.38.1.4 | TNamedItem | not-accessible | The value of vRtrMplsLspStatsLspName indicates the lsp name. |
| T/F vRtrMplsLspStatsPSBMatch | 1.3.6.1.4.1.6527.3.1.2.6.39.1.97 | TruthValue | read-only | The value of vRtrMplsLspStatsPSBMatch indicates if a path state block (PSB) match was made against this LSP name. |
| ROW vRtrMplsLspStatsRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.38.1.5 | RowStatus | read-create | vRtrMplsLspStatsRowStatus is used for the creation or deletion of entries in the vRtrMplsLspStatsTable. |
| IP vRtrMplsLspStatsSenderAddr | 1.3.6.1.4.1.6527.3.1.2.6.38.1.3 | InetAddress | not-accessible | The value of vRtrMplsLspStatsSenderAddr indicates the sender address. |
| IPt vRtrMplsLspStatsSenderAddrType | 1.3.6.1.4.1.6527.3.1.2.6.38.1.2 | InetAddressType | not-accessible | The value of vRtrMplsLspStatsSenderAddrType indicates address type of vRtrMplsLspStatsSenderAddr. |
| vRtrMplsLspStatsTable | 1.3.6.1.4.1.6527.3.1.2.6.38 | not-accessible | vRtrMplsLspStatsTable controls Statsistics in the ess data-path at the ingress Label Switched Path (LSP) for an Mpls-Lsp FEC. | |
| TIM vRtrMplsLspStatsTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.6.37 | TimeStamp | read-only | Timestamp of the last change to the vRtrMplsLspStatsTable either from adding a row or removing a row. |
| T/F vRtrMplsLspStatsTpOnly | 1.3.6.1.4.1.6527.3.1.2.6.39.1.98 | TruthValue | read-only | The value of vRtrMplsLspStatsTpOnly indicates whether the statistics apply to mpls-tp lsp or for regular rsvp-te signalled terminating LSP. The value of 'true' indicates the statistics apply to mpls-tp LSP only. The value of 'false' indicates the statistics apply for regular rsvp-te signalled terminating LSP. |
| INT vRtrMplsLspStatsType | 1.3.6.1.4.1.6527.3.1.2.6.38.1.1 | INTEGER | not-accessible | The value of vRtrMplsLspStatsType indicates the type of statistics. |
| vRtrMplsLspStatTable | 1.3.6.1.4.1.6527.3.1.2.6.2 | not-accessible | The vRtrMplsLspStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| NTF vRtrMplsLspSwitchStbyFailure | 1.3.6.1.4.1.6527.3.1.3.6.0.20 | [CAUSE] The vRtrMplsLspSwitchStbyFailure notification is generated to report an unsuccessful switchover from the current active secondary LSP path of an LSP to another secondary standby LSP path. The reason for the failure is specified by vRtrMplsLspSwitchStbyReasonCode. [EFFECT] The switchover to the new standby path failed for the LSP. [RECOVERY] The vRtrMplsLspSwitchStbyReasonCode will help the user troubleshoot the failure. The user can attempt to switchover to another standby LSP path again. | ||
| TMN vRtrMplsLspSwitchStbyPath | 1.3.6.1.4.1.6527.3.1.2.6.1.1.55 | TmnxActionType | read-create | The value of vRtrMplsLspSwitchStbyPath specifies whether to trigger the switch from the current active standby LSP path to a new LSP path as specified by vRtrMplsLspSwitchStbyPathIndex. When SET to the value of 'doAction', if the LSP path is actively on a current standby path, signaling will be initiated to switch to the new path. If a signal is triggered while a re-signaling is already in progress, the old transient state will be destroyed and a new transaction will be triggered. This variable must be set along with vRtrMplsLspSwitchStbyPathIndex to indicate the specific path index to switch to. An SNMP GET request on this object should return 'notApplicable'. |
| T/F vRtrMplsLspSwitchStbyPathForce | 1.3.6.1.4.1.6527.3.1.2.6.1.1.57 | TruthValue | read-create | The value of vRtrMplsLspSwitchStbyPathForce specifies whether to force a switch from an active LSP path to a new standby path as specified by the values of vRtrMplsLspSwitchStbyPathIndex and vRtrMplsLspSwitchStbyPath. When vRtrMplsLspSwitchStbyPathForce variable is specified vRtrMplsLspSwitchStbyPathIndex and vRtrMplsLspSwitchStbyPath must be also be specified. A value of 'true' for vRtrMplsLspSwitchStbyPathForce specifies a forced switch. A value of 'false' specifies no forced switch. |
| MPL vRtrMplsLspSwitchStbyPathIndex | 1.3.6.1.4.1.6527.3.1.2.6.1.1.56 | MplsTunnelIndex | read-create | The value of vRtrMplsLspSwitchStbyPathIndex specifies the index for the new standby LSP path in mplsTunnelTable. vRtrMplsLspSwitchStbyPath must also be set to 'doAction' for the new standby LSP path to be selected. A value of 0 specifies that the best active path will be selected. |
| INT vRtrMplsLspSwitchStbyReasonCode | 1.3.6.1.4.1.6527.3.1.2.6.16.13 | INTEGER | accessible-for-notify | The value of vRtrMplsLspSwitchStbyReasonCode indicates the reason for the failure of switch to a new standby path from the current active standby path. |
| vRtrMplsLspTable | 1.3.6.1.4.1.6527.3.1.2.6.1 | not-accessible | The vRtrMplsLspTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| T/F vRtrMplsLspTemplateAdaptive | 1.3.6.1.4.1.6527.3.1.2.6.41.1.6 | TruthValue | read-create | The value of vRtrMplsLspTemplateAdaptive specifies whether the make-before-break functionality is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateAdaptive is set to 'true', make-before-break functionality is enabled. When the value is set to 'false' make-before-break functionality is disabled. |
| U32 vRtrMplsLspTemplateAdmGrpExcl | 1.3.6.1.4.1.6527.3.1.2.6.41.1.11 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateAdmGrpExcl specifies a bit-map of admin groups that are excluded when the dynamically created LSPs using this template are setup. If bit 'n' is set, then the admin group with value 'n' is excluded. This implies that each link that the LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list. |
| U32 vRtrMplsLspTemplateAdmGrpIncl | 1.3.6.1.4.1.6527.3.1.2.6.41.1.10 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateAdmGrpIncl specifies a bit-map of admin groups that are included when the dynamically created LSPs using this template are setup . If bit 'n' is set, then the admin group with value 'n' is included. This implies that each link that the LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list. |
| TMN vRtrMplsLspTemplateAdminState | 1.3.6.1.4.1.6527.3.1.2.6.41.1.4 | TmnxAdminState | read-create | The value of vRtrMplsLspTemplateAdminState specifies the current administrative state of the LSP Template. |
| I32 vRtrMplsLspTemplateBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.41.1.7 | Integer32 | read-create | The value of vRtrMplsLspTemplateBandwidth specifies the amount of bandwidth in mega-bits per seconds (Mbps) to be reserved for the LSPs that are dynamically created using this LSP template. A value of zero (0) indicates that no bandwidth is reserved. |
| T/F vRtrMplsLspTemplateCspf | 1.3.6.1.4.1.6527.3.1.2.6.41.1.8 | TruthValue | read-create | The value of vRtrMplsLspTemplateCspf specifies whether the CSPF computation for constrained-path LSP is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateCspf is set to 'true', CSPF computation for constrained-path is enabled. When the value is set to 'false', CSPF computation for constrained-path is disabled. |
| T/F vRtrMplsLspTemplateCspfTeMetric | 1.3.6.1.4.1.6527.3.1.2.6.41.1.20 | TruthValue | read-create | The value of vRtrMplsLspTemplateCspfTeMetric specifies whether the TE metric is used for the purpose of the LSP path computation by CSPF (Constrained Shortest Path First). When the value of vRtrMplsLspTemplateCspfTeMetric is set to 'true', the TE metric is used to compute the path of the LSP by CSPF. When the value of vRtrMplsLspTemplateCspfTeMetric is set to 'false', IGP metric is used to compute the path of the LSP by CSPF. |
| MPL vRtrMplsLspTemplateDefaultPath | 1.3.6.1.4.1.6527.3.1.2.6.41.1.9 | MplsTunnelIndex | read-create | The value of vRtrMplsLspTemplateDefaultPath specifies the default path used to signal LSPs that are dynamically created using this LSP template. If a corresponding index does not exist in MPLS-TE-MIB::mplsTunnelTable, an 'inconsistentValue' error will be returned. |
| vRtrMplsLspTemplateEntry | 1.3.6.1.4.1.6527.3.1.2.6.41.1 | not-accessible | Each row entry represents a Labeled Switch Path Template (LSP Template) configured for a virtual router in the system. Entries in this table can be created and deleted via SNMP SET operations. | |
| T/F vRtrMplsLspTemplateFastReroute | 1.3.6.1.4.1.6527.3.1.2.6.41.1.12 | TruthValue | read-create | The value of vRtrMplsLspTemplateFastReroute specifies whether fast reroute is enabled for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateFastReroute is set to 'true', fast reroute is enabled for the LSP. When the value of vRtrMplsLspTemplateFastReroute is set to'false', fast reroute is disabled. |
| U32 vRtrMplsLspTemplateFRHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.41.1.14 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateFRHopLimit specifies the total number of hops a detour or backup LSP can take before merging back onto the main LSP path. |
| INT vRtrMplsLspTemplateFRMethod | 1.3.6.1.4.1.6527.3.1.2.6.41.1.13 | INTEGER | read-create | The value of vRtrMplsLspTemplateFRMethod specifies the fast reroute method used for the LSPs that are dynamically created using this LSP template. When the value of vRtrMplsLspTemplateFRMethod is set to 'oneToOneBackup', a backup LSP is established which will intersect the original LSP somewhere downstream of the point of link or node failure. For each LSP that is backed up, a separate backup LSP is established. When the value of vRtrMplsLspTemplateFRMethod is set to 'facilityBackup', Instead of creating a separateLSP for every LSP that is to be backed up, a single LSP is created which serves as a backup for a set of LSPs. For LSP templates of type P2MP, oneToOneBackup is not supported. |
| U32 vRtrMplsLspTemplateHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.41.1.15 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateHopLimit specifies the maximum number of hops that a dynamically created LSP will traverse including the ingress and egress ESRs. A LSP will not be set up if the hop limit is exceeded. |
| TIM vRtrMplsLspTemplateLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.41.1.3 | TimeStamp | read-only | The value of vRtrMplsLspTemplateLastChanged indicates the timestamp of last change to this row in vRtrMplsLspTemplateTable. |
| G32 vRtrMplsLspTemplateLspCount | 1.3.6.1.4.1.6527.3.1.2.6.41.1.21 | Gauge32 | read-only | The value of vRtrMplsLspTemplateLspCount indicates the number of LSPs of type 'p2mpAuto' that are created using this template. |
| G32 vRtrMplsLspTemplateMvpnRefCount | 1.3.6.1.4.1.6527.3.1.2.6.41.1.22 | Gauge32 | read-only | The value of vRtrMplsLspTemplateMvpnRefCount indicates the number of MVPNs as well as number of P2MP LSP users associated to this template. |
| TNA vRtrMplsLspTemplateName | 1.3.6.1.4.1.6527.3.1.2.6.41.1.1 | TNamedItem | not-accessible | The value of the object vRtrMplsLspTemplateName specifies the name of the LSP Template which is used as a guideline to create and signal multiple LSP instances when dynamic LSP creation is required. |
| INT vRtrMplsLspTemplateRecord | 1.3.6.1.4.1.6527.3.1.2.6.41.1.16 | INTEGER | read-create | The value of vRtrMplsLspTemplateRecord specifies whether the recording of all the hops is enabled for LSPs that are dynamically created using this template. When the value of vRtrMplsLspTemplateRecord is set to 'record', recording of all the hops that a LSP traverses is enabled. When the value of vRtrMplsLspTemplateRecord is set to 'noRecord', recording of all the hops that a LSP traverses is disabled. |
| INT vRtrMplsLspTemplateRecordLabel | 1.3.6.1.4.1.6527.3.1.2.6.41.1.17 | INTEGER | read-create | The value of vRtrMplsLspTemplateRecordLabel specifies whether the recording of labels is enabled for LSPs that are dynamically created using this LSP template . When the value of vRtrMplsLspTemplateRecordLabel is set to 'record', recording of labels at each node that a LSP traverses is enabled. When the value of vRtrMplsLspTemplateRecordLabel is set to 'noRecord', recording of labels at each node that a LSP traverses is disabled. |
| U32 vRtrMplsLspTemplateRetryLimit | 1.3.6.1.4.1.6527.3.1.2.6.41.1.18 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateRetryLimit specifies the maximum number of attempts made to establish an LSP that is dynamically created using this template. A value of zero(0) specifies that an infinite number of retry attempts should be made. |
| U32 vRtrMplsLspTemplateRetryTimer | 1.3.6.1.4.1.6527.3.1.2.6.41.1.19 | Unsigned32 | read-create | The value of vRtrMplsLspTemplateRetryTimer specifies the time in seconds a dynamically created Lsp waits before it attempts to re-establish itself. |
| ROW vRtrMplsLspTemplateRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.41.1.2 | RowStatus | read-create | The value of vRtrMplsLspTemplateRowStatus specifies the Row Status for this entry. |
| vRtrMplsLspTemplateTable | 1.3.6.1.4.1.6527.3.1.2.6.41 | not-accessible | The vRtrMplsLspTemplateTable has an entry for each Labeled Switch Path Template(LSP Template) configured for a virtual router in the system. The table contains a list of LSP Templates that are referenced when dynamic LSP creation is required. | |
| TIM vRtrMplsLspTemplateTblLastChgd | 1.3.6.1.4.1.6527.3.1.2.6.40 | TimeStamp | read-only | The value of vRtrMplsLspTemplateTblLastChgd indicates the sysUpTime at the time of the last modification of an entry in the vRtrMplsLspTemplateTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| INT vRtrMplsLspTemplateType | 1.3.6.1.4.1.6527.3.1.2.6.41.1.5 | INTEGER | read-create | The value of vRtrMplsLspTemplateType specifies the type of the LSP template. When the value of vRtrMplsLspTemplateType is set to 'p2mp', the template is used for auto creation of P2MP LSPs. |
| NUM vRtrMplsLspTimeDown | 1.3.6.1.4.1.6527.3.1.2.6.2.1.5 | TimeInterval | read-only | The total time in 10-millisecond units that this LSP has not been operational. |
| NUM vRtrMplsLspTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.2.1.4 | TimeInterval | read-only | The total time in 10-millisecond units that this LSP has been been operational. For example, the percentage up time can be determined by computing (vRtrMplsLspTimeUp/vRtrMplsLspAge * 100 %). |
| IP vRtrMplsLspToAddr | 1.3.6.1.4.1.6527.3.1.2.6.1.1.8 | IpAddress | read-create | Destination IP address of this LSP. This LSP will not be signaled until vRtrMplsLspToAddr is explicitly set. |
| TMN vRtrMplsLspToAddrType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.61 | TmnxMplsLspAddrType | read-create | The vRtrMplsLspToAddrType object is an enumerated value that specifies the destination address type of the LSP. The value of 'ipv4' specifies an IPv4 address and vRtrMplsLspToAddr should be configured. The value of 'nodeId' specifies an MPLS-TP node id and vRtrMplsLspToNodeId should be configured. |
| TMN vRtrMplsLspToNodeId | 1.3.6.1.4.1.6527.3.1.2.6.1.1.63 | TmnxMplsTpNodeID | read-create | The value of vRtrMplsLspToNodeId specifies the destination node id of an MPLS-TP Static LSP. vRtrMplsLspToNodeId is configured when vRtrMplsLspToAddrType is set to 'nodeId'. |
| C32 vRtrMplsLspTransitions | 1.3.6.1.4.1.6527.3.1.2.6.2.1.7 | Counter32 | read-only | The number of state transitions (up -> down and down -> up) this LSP has undergone. |
| INT vRtrMplsLspType | 1.3.6.1.4.1.6527.3.1.2.6.1.1.9 | INTEGER | read-create | The vRtrMplsLspType object is an enumerated value that indicates whether the label value is statically or dynamically assigned or whether the LSP will be used exclusively for bypass protection. The value 'p2mpLsp' will be used to indicate point to multipoint LSPs used for multicast traffic. When the value of the vRtrMplsLspType is 'p2mpAuto', it specifies that the LSP is auto-created dynamically by the system and the row entry is dynamically created by the system using LSP Template values configured in the associated row entry of vRtrMplsLspTemplateTable. The value 'mplsTp' specifies that the LSP is an MPLS-TP Static LSP. A 'wrongValue' error is returned if an attempt is made to set an object in the row entry where the value of vRtrMplsLspType is 'p2mpAuto'. |
| NTF vRtrMplsLspUp | 1.3.6.1.4.1.6527.3.1.3.6.0.3 | This Notification is generated when a LSP transitions to the 'inService' state from any other state. | ||
| T/F vRtrMplsLspVprnAutoBindInclude | 1.3.6.1.4.1.6527.3.1.2.6.1.1.46 | TruthValue | read-create | The value of vRtrMplsLspVprnAutoBindInclude specifies whether the LSP can be used as part of the auto-bind feature for VPRN services. By default a LSP is available for inclusion to be used for the auto-bind feature. By default, static and dynamic LSPs will be included when they are created. The default value for p2mp and bypass-only LSPs will be 'false'. |
| NUM vRtrMplsNotifyRow | 1.3.6.1.4.1.6527.3.1.2.6.16.3 | RowPointer | accessible-for-notify | used by Alcatel-Lucent SROS series MPLS Configuration change Notifications, the object ID indicates the MPLS table and entry. |
| C64 vRtrMplsOutOfProfOctetsFc0 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.73 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc0 indicates the number of out of profile octets received for Forwarding Class 0. |
| C32 vRtrMplsOutOfProfOctetsFc0High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.75 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc0 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc0. |
| C32 vRtrMplsOutOfProfOctetsFc0Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.74 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc0 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc0. |
| C64 vRtrMplsOutOfProfOctetsFc1 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.76 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc1 indicates the number of out of profile octets received for Forwarding Class 1. |
| C32 vRtrMplsOutOfProfOctetsFc1High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.78 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc1 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc1. |
| C32 vRtrMplsOutOfProfOctetsFc1Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.77 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc1 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc1. |
| C64 vRtrMplsOutOfProfOctetsFc2 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.79 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc2 indicates the number of out of profile octets received for Forwarding Class 2. |
| C32 vRtrMplsOutOfProfOctetsFc2High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.81 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc2 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc2. |
| C32 vRtrMplsOutOfProfOctetsFc2Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.80 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc2 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc2. |
| C64 vRtrMplsOutOfProfOctetsFc3 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.82 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc3 indicates the number of out of profile octets received for Forwarding Class 3. |
| C32 vRtrMplsOutOfProfOctetsFc3High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.84 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc3 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc3. |
| C32 vRtrMplsOutOfProfOctetsFc3Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.83 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc3 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc3. |
| C64 vRtrMplsOutOfProfOctetsFc4 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.85 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc4 indicates the number of out of profile octets received for Forwarding Class 4. |
| C32 vRtrMplsOutOfProfOctetsFc4High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.87 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc4 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc4. |
| C32 vRtrMplsOutOfProfOctetsFc4Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.86 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc4 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc4. |
| C64 vRtrMplsOutOfProfOctetsFc5 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.88 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc5 indicates the number of out of profile octets received for Forwarding Class 5. |
| C32 vRtrMplsOutOfProfOctetsFc5High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.90 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc5 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc5. |
| C32 vRtrMplsOutOfProfOctetsFc5Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.89 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc5 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc5. |
| C64 vRtrMplsOutOfProfOctetsFc6 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.91 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc6 indicates the number of out of profile octets received for Forwarding Class 6. |
| C32 vRtrMplsOutOfProfOctetsFc6High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.93 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc6 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc6. |
| C32 vRtrMplsOutOfProfOctetsFc6Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.92 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc6 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc6. |
| C64 vRtrMplsOutOfProfOctetsFc7 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.94 | Counter64 | read-only | The value of vRtrMplsOutOfProfOctetsFc7 indicates the number of out of profile octets received for Forwarding Class 7. |
| C32 vRtrMplsOutOfProfOctetsFc7High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.96 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc7 indicates the higher 32 bits of the value of vRtrMplsOutOfProfOctetsFc7. |
| C32 vRtrMplsOutOfProfOctetsFc7Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.95 | Counter32 | read-only | The value of vRtrMplsOutOfProfOctetsFc7 indicates the lower 32 bits of the value of vRtrMplsOutOfProfOctetsFc7. |
| C64 vRtrMplsOutOfProfPktsFc0 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.49 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc0 indicates the number of out of profile packets received for Forwarding Class 0. |
| C32 vRtrMplsOutOfProfPktsFc0High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.51 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc0 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc0. |
| C32 vRtrMplsOutOfProfPktsFc0Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.50 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc0 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc0. |
| C64 vRtrMplsOutOfProfPktsFc1 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.52 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc1 indicates the number of out of profile packets received for Forwarding Class 1. |
| C32 vRtrMplsOutOfProfPktsFc1High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.54 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc1 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc1. |
| C32 vRtrMplsOutOfProfPktsFc1Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.53 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc1 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc1. |
| C64 vRtrMplsOutOfProfPktsFc2 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.55 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc2 indicates the number of out of profile packets received for Forwarding Class 2. |
| C32 vRtrMplsOutOfProfPktsFc2High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.57 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc2 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc2. |
| C32 vRtrMplsOutOfProfPktsFc2Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.56 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc2 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc2. |
| C64 vRtrMplsOutOfProfPktsFc3 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.58 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc3 indicates the number of out of profile packets received for Forwarding Class 3. |
| C32 vRtrMplsOutOfProfPktsFc3High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.60 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc3 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc3. |
| C32 vRtrMplsOutOfProfPktsFc3Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.59 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc3 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc3. |
| C64 vRtrMplsOutOfProfPktsFc4 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.61 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc4 indicates the number of out of profile packets received for Forwarding Class 4. |
| C32 vRtrMplsOutOfProfPktsFc4High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.63 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc4 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc4. |
| C32 vRtrMplsOutOfProfPktsFc4Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.62 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc4 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc4. |
| C64 vRtrMplsOutOfProfPktsFc5 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.64 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc5 indicates the number of out of profile packets received for Forwarding Class 5. |
| C32 vRtrMplsOutOfProfPktsFc5High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.66 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc5 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc5. |
| C32 vRtrMplsOutOfProfPktsFc5Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.65 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc5 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc5. |
| C64 vRtrMplsOutOfProfPktsFc6 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.67 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc6 indicates the number of out of profile packets received for Forwarding Class 6. |
| C32 vRtrMplsOutOfProfPktsFc6High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.69 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc6 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc6. |
| C32 vRtrMplsOutOfProfPktsFc6Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.68 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc6 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc6. |
| C64 vRtrMplsOutOfProfPktsFc7 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.70 | Counter64 | read-only | The value of vRtrMplsOutOfProfPktsFc7 indicates the number of out of profile packets received for Forwarding Class 7. |
| C32 vRtrMplsOutOfProfPktsFc7High32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.72 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc7 indicates the higher 32 bits of the value of vRtrMplsOutOfProfPktsFc7. |
| C32 vRtrMplsOutOfProfPktsFc7Low32 | 1.3.6.1.4.1.6527.3.1.2.6.39.1.71 | Counter32 | read-only | The value of vRtrMplsOutOfProfPktsFc7 indicates the lower 32 bits of the value of vRtrMplsOutOfProfPktsFc7. |
| vRtrMplsOutSegmentEntry | 1.3.6.1.4.1.6527.3.1.2.6.35.1 | not-accessible | A row entry in this table corresponds to a row entry in the mplsOutSegmentTable and adds to the information contained in that table. | |
| I32 vRtrMplsOutSegmentIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.4 | Integer32 | read-only | An index of the mplsXCTable. It represents mplsOutSegmentIndex of the mplsOutSegmentTable. |
| U32 vRtrMplsOutSegmentNumS2ls | 1.3.6.1.4.1.6527.3.1.2.6.35.1.1 | Unsigned32 | read-only | The value of vRtrMplsOutSegmentNumS2ls specifies number of S2Ls on the outsegment. |
| vRtrMplsOutSegmentTable | 1.3.6.1.4.1.6527.3.1.2.6.35 | not-accessible | The vRtrMplsOutSegmentTable augments the mplsOutSegmentTable in the MPLS-LSR-MIB. | |
| T/F vRtrMplsP2mpInstAdaptive | 1.3.6.1.4.1.6527.3.1.2.6.25.1.23 | TruthValue | read-create | The value of vRtrMplsP2mpInstAdaptive specifies whether make-before-break functionality is enabled. If the value of vRtrMplsP2mpInstAdaptive is set to 'true', it enables make-before-break functionality for the P2MP LSP. When the attributes of an already established P2MP LSP are changed, either through manual configuration or due to a change in network topology, make-before-break functionality ensures that the resources of the existing P2MP LSP will not be released until a new path (with the same P2MP LSP Id) has been established and traffic flowing over the existing path is seamlessly transferred to the new path. If the value of vRtrMplsP2mpInstAdaptive is set to 'false', it disables make-before-break functionality. |
| U32 vRtrMplsP2mpInstAdminGrpExclude | 1.3.6.1.4.1.6527.3.1.2.6.25.1.22 | Unsigned32 | read-create | The value of vRtrMplsP2mpInstAdminGrpExclude is a bit-map that specifies a list of admin groups that should be excluded when this P2MP LSP is setup. If bit 'n' is set, then the admin group with value 'n' is excluded for this P2MP LSP. This implies that each link that this P2MP LSP goes through must not be associated with any of the admin groups in the exclude list. By default, no admin groups are in the exclude list. |
| U32 vRtrMplsP2mpInstAdminGrpInclude | 1.3.6.1.4.1.6527.3.1.2.6.25.1.21 | Unsigned32 | read-create | The value of vRtrMplsP2mpInstAdminGrpInclude is a bit-map that specifies a list of admin groups that should be included when this P2MP LSP is setup. If bit 'n' is set, then the admin group with value 'n' is included for this P2MP LSP. This implies that each link that this P2MP LSP goes through must be associated with at least one of the admin groups in the include list. By default, all admin groups are in the include list. |
| TMN vRtrMplsP2mpInstAdminState | 1.3.6.1.4.1.6527.3.1.2.6.25.1.13 | TmnxAdminState | read-create | The value of vRtrMplsP2mpInstAdminState specifies desired administrative state for this P2MP LSP. |
| NTF vRtrMplsP2mpInstanceDown | 1.3.6.1.4.1.6527.3.1.3.6.0.10 | This Notification is generated when a P2MP instance transitions out of 'inService' state to any other state. | ||
| NTF vRtrMplsP2mpInstanceResignaled | 1.3.6.1.4.1.6527.3.1.3.6.0.17 | This Notification is generated when a P2MP instance is resignaled. The vRtrMplsP2mpInstLastMBBType indicates the reason why the P2MP instance was resignaled. | ||
| NTF vRtrMplsP2mpInstanceUp | 1.3.6.1.4.1.6527.3.1.3.6.0.9 | This Notification is generated when a P2MP instance transitions to the 'inService' state from any other state. | ||
| U32 vRtrMplsP2mpInstBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.25.1.7 | Unsigned32 | read-create | The value of vRtrMplsP2mpInstBandwidth specifies the amount of bandwidth in mega-bits per second (Mbps) to be reserved for the P2MP LSP. |
| vRtrMplsP2mpInstEntry | 1.3.6.1.4.1.6527.3.1.2.6.25.1 | not-accessible | vRtrMplsP2mpInstEntry is an entry (conceptual row) in the vRtrMplsP2mpInstTable. Each entry represents the configuration for a Mpls Point to Multipoint (P2MP) Instance. Entries in this table can be created and deleted via SNMP SET operations. | |
| TMN vRtrMplsP2mpInstFailCode | 1.3.6.1.4.1.6527.3.1.2.6.25.1.18 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsP2mpInstFailCode indicates the reason code for P2MP LSP Path failure. A value of 0 indicates that no failure has occurred. |
| IP vRtrMplsP2mpInstFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.25.1.20 | InetAddress | read-only | The value of vRtrMplsP2mpInstFailNodeAddr indicates the IP address of the node in the P2MP LSP path at which the P2MP LSP path failed. |
| IPt vRtrMplsP2mpInstFailNodeArType | 1.3.6.1.4.1.6527.3.1.2.6.25.1.19 | InetAddressType | read-only | The value of vRtrMplsP2mpInstFailNodeArType indicates the type of vRtrMplsP2mpInstFailNodeAddr. When no failure has occurred, vRtrMplsP2mpInstFailNodeArType is 0. |
| U32 vRtrMplsP2mpInstHoldPriority | 1.3.6.1.4.1.6527.3.1.2.6.25.1.10 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstHoldPriority indicates the hold priority to use when insufficient bandwidth is available to setup a P2MP LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this P2MP LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit. |
| U32 vRtrMplsP2mpInstHopLimit | 1.3.6.1.4.1.6527.3.1.2.6.25.1.12 | Unsigned32 | read-create | The value of vRtrMplsP2mpInstHopLimit specifies the maximum number of hops that a P2MP LSP will traverse including the ingress and egress ESRs. A P2MP LSP will not be setup if the hop limit is exceeded. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit. |
| TMN vRtrMplsP2mpInstIndex | 1.3.6.1.4.1.6527.3.1.2.6.25.1.1 | TmnxVRtrMplsLspID | not-accessible | The unique value which identifies this Point to Multipoint Labeled Switch Path (P2MP LSP) for this virtual router in the Alcatel-Lucent SROS system. It is a unique value among entries with the same value of vRtrID. |
| U32 vRtrMplsP2mpInstInheritance | 1.3.6.1.4.1.6527.3.1.2.6.25.1.15 | Unsigned32 | read-create | The value of vRtrMplsP2mpInstInheritance specifies whether or not each writable object in this row inherits its value from its corresponding object in the vRtrMplsLspTable. This object controls whether to inherit the operational value of that associated object, or use the administrative value configured in this row. Non mask bits will always have value of zero, and any attempt to change the value will be silently discarded. This object is a bit-mask, with the following positions: vRtrMplsP2mpInstHopLimit 0x40 vRtrMplsP2mpInstAdminGrpInclude 0x200 vRtrMplsP2mpInstAdminGrpExclude 0x400 vRtrMplsP2mpInstAdaptive 0x800 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. The corresponding mask bit will be changed to one when SNMP SET is performed on any of the inherited objects (vRtrMplsP2mpInstHopLimit, vRtrMplsP2mpInstAdminGrpInclude, etc). When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrMplsLspTable. |
| TIM vRtrMplsP2mpInstLastChange | 1.3.6.1.4.1.6527.3.1.2.6.25.1.3 | TimeStamp | read-only | The value of vRtrMplsP2mpInstLastChange indicates the timestamp of last change to this row in vRtrMplsP2mpInstTable. |
| TIM vRtrMplsP2mpInstLastMBBEnd | 1.3.6.1.4.1.6527.3.1.2.6.25.1.31 | TimeStamp | read-only | The value of vRtrMplsP2mpInstLastMBBEnd indicates the sysUpTime when the last MBB ended. |
| U32 vRtrMplsP2mpInstLastMBBMetric | 1.3.6.1.4.1.6527.3.1.2.6.25.1.32 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstLastMBBMetric indicates the cost of the traffic engineered path for the P2MP LSP path prior to MBB. |
| INT vRtrMplsP2mpInstLastMBBState | 1.3.6.1.4.1.6527.3.1.2.6.25.1.33 | INTEGER | read-only | The value of vRtrMplsP2mpInstLastMBBState specifies whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed. |
| TMN vRtrMplsP2mpInstLastMBBType | 1.3.6.1.4.1.6527.3.1.2.6.25.1.30 | TmnxMplsMBBType | read-only | The value of vRtrMplsP2mpInstLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted. |
| TIM vRtrMplsP2mpInstLastResigAttpt | 1.3.6.1.4.1.6527.3.1.2.6.25.1.28 | TimeStamp | read-only | The value of vRtrMplsP2mpInstLastResigAttpt indicates the sysUpTime when the last attempt to resignal this P2MP LSP was made. |
| MPL vRtrMplsP2mpInstLspId | 1.3.6.1.4.1.6527.3.1.2.6.25.1.16 | MplsLSPID | read-only | The value of vRtrMplsP2mpInstLspId indicates the value which identifies the label switched path that is signaled for this entry. |
| TMN vRtrMplsP2mpInstMBBFailCode | 1.3.6.1.4.1.6527.3.1.2.6.25.1.38 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsP2mpInstMBBFailCode indicates the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred. |
| IP vRtrMplsP2mpInstMBBFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.25.1.40 | InetAddress | read-only | The value of vRtrMplsP2mpInstMBBFailNodeAddr indicates the IP address of the node in the P2MP LSP path at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsP2mpInstMBBFailNodeType and empty string for vRtrMplsP2mpInstMBBFailNodeAddr indicates that no failure has occurred. |
| IPt vRtrMplsP2mpInstMBBFailNodeType | 1.3.6.1.4.1.6527.3.1.2.6.25.1.39 | InetAddressType | read-only | The value of vRtrMplsP2mpInstMBBFailNodeType indicates the type of vRtrMplsP2mpInstMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred. |
| U32 vRtrMplsP2mpInstMBBNextRetry | 1.3.6.1.4.1.6527.3.1.2.6.25.1.36 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB. |
| U32 vRtrMplsP2mpInstMBBRetryAttpts | 1.3.6.1.4.1.6527.3.1.2.6.25.1.37 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstMBBRetryAttpts indicates 'n' where nth attempt for the MBB is in progress. |
| TIM vRtrMplsP2mpInstMBBStarted | 1.3.6.1.4.1.6527.3.1.2.6.25.1.35 | TimeStamp | read-only | The value of vRtrMplsP2mpInstMBBStarted indicates the sysUpTime when the in-progress MBB started. |
| TMN vRtrMplsP2mpInstMBBTypeInProg | 1.3.6.1.4.1.6527.3.1.2.6.25.1.34 | TmnxMplsMBBType | read-only | The value of vRtrMplsP2mpInstMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress. |
| U32 vRtrMplsP2mpInstMetric | 1.3.6.1.4.1.6527.3.1.2.6.25.1.29 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstMetric indicates the cost of the traffic engineered path returned by the IGP. |
| TNA vRtrMplsP2mpInstName | 1.3.6.1.4.1.6527.3.1.2.6.25.1.4 | TNamedItemOrEmpty | read-create | The value of vRtrMplsP2mpInstName specifies the administrative name for the P2MP instance which must be unique within a virtual router instance. |
| U32 vRtrMplsP2mpInstNegotiatedMTU | 1.3.6.1.4.1.6527.3.1.2.6.25.1.17 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstNegotiatedMTU indicates the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this P2MP LSP path. |
| TMN vRtrMplsP2mpInstNotifIndex | 1.3.6.1.4.1.6527.3.1.2.6.16.4 | TmnxVRtrMplsLspID | accessible-for-notify | The unique value which identifies this Point to Multipoint Labeled Switch Path (P2MP LSP) for this virtual router in the Alcatel-Lucent SROS system. It is a unique value among entries with the same value of vRtrID. |
| TMN vRtrMplsP2mpInstNotifReasonCode | 1.3.6.1.4.1.6527.3.1.2.6.16.5 | TmnxMplsP2mpInstFailCode | accessible-for-notify | Used by vRtrMplsP2mpInstanceDown, the value indicates the reason for the P2MP instance going down. |
| I32 vRtrMplsP2mpInstOperBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.25.1.24 | Integer32 | read-only | The value of vRtrMplsP2mpInstOperBandwidth indicates the amount of bandwidth in mega-bits per seconds (Mbps) that has been reserved for the operational P2MP LSP path. When make-before-break functionality for the P2MP LSP is enabled and if the path bandwidth is changed, the resources allocated to the existing P2MP LSP paths will not be released until a new path with the new bandwidth settings has been established. While a new path is being signaled, the administrative value and the operational values of the path bandwidth may differ. The value of vRtrMplsP2mpInstBandwidth specifies the bandwidth requirements for the new P2MP LSP path trying to be established whereas the value of vRtrMplsP2mpInstOperBandwidth specifies the bandwidth reserved for the existing P2MP LSP path. |
| U32 vRtrMplsP2mpInstOperMTU | 1.3.6.1.4.1.6527.3.1.2.6.25.1.26 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstOperMTU indicates the size for the Maximum transmission unit (MTU) that is currently in operation for this P2MP LSP Path. |
| TMN vRtrMplsP2mpInstOperState | 1.3.6.1.4.1.6527.3.1.2.6.25.1.14 | TmnxOperState | read-only | The value of vRtrMplsP2mpInstOperState indicates the current operational state of this P2MP LSP. |
| BIT vRtrMplsP2mpInstProperties | 1.3.6.1.4.1.6527.3.1.2.6.25.1.6 | Bits | read-only | The value of vRtrMplsP2mpInstProperties indicates the set of configured properties for this path expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value 1 is set. |
| T/F vRtrMplsP2mpInstRecord | 1.3.6.1.4.1.6527.3.1.2.6.25.1.11 | TruthValue | read-create | The value of vRtrMplsP2mpInstRecord specifies whether recording of all hops that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecord is 'true', recording of all the hops that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecord is 'false, recording of all the hops that a P2MP LSP traverses is disabled. |
| INT vRtrMplsP2mpInstRecordLabel | 1.3.6.1.4.1.6527.3.1.2.6.25.1.27 | INTEGER | read-create | The value of vRtrMplsP2mpInstRecordLabel specifies when the value of vRtrMplsP2mpInstRecordLabel is 'record', recording of labels at each node that a P2MP LSP traverses is enabled. When the value of vRtrMplsP2mpInstRecordLabel is 'noRecord', recording of labels at each node that a P2MP LSP traverses is disabled. |
| TMN vRtrMplsP2mpInstResignal | 1.3.6.1.4.1.6527.3.1.2.6.25.1.25 | TmnxActionType | read-create | Setting the value of vRtrMplsP2mpInstResignal to 'doAction' triggers the re-signaling of the P2MP LSP path. If the P2MP LSP path is operationally down either due to network failure or due to the retry attempts count being exceeded, setting this variable to 'doAction' will initiate the signaling for the path. A make-before-break signaling for the path will be initiated if the P2MP LSP is operationally up but the make-before-break retry attempts count was exceeded. Make-before-break signaling will also be initiated for any P2MP LSP that is operationally up. This may be used to cause a loose-hop P2MP LSP to be optimized. If a re-signal is triggered while a re-signaling is already in progress, the old transient state will be destroyed and a new transaction being triggered. An SNMP GET request on this object should return 'notApplicable'. |
| ROW vRtrMplsP2mpInstRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.25.1.2 | RowStatus | read-create | vRtrMplsP2mpInstRowStatus is used to create, delete or control entries in the vRtrMplsP2mpInstTable. |
| U32 vRtrMplsP2mpInstSetupPriority | 1.3.6.1.4.1.6527.3.1.2.6.25.1.9 | Unsigned32 | read-only | The value of vRtrMplsP2mpInstSetupPriority indicates the setup priority to use when insufficient bandwidth is available to setup a P2MP LSP. The setup priority is compared against the hold priority of existing LSPs. If the setup priority is higher than the hold priority of the established LSPs, this P2MP LSP may preempt the other LSPs. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. When the vRtrMplsP2mpInstHopLimit bit in vRtrMplsP2mpInstInheritance is cleared (0), the value returned to a GET request is inherited from vRtrMplsLspHopLimit. |
| G32 vRtrMplsP2mpInstStatConfiguredS2ls | 1.3.6.1.4.1.6527.3.1.2.6.26.1.3 | Gauge32 | read-only | The value of vRtrMplsP2mpInstStatConfiguredS2ls indicates the number of S2ls configured for this P2MP LSP. |
| INT vRtrMplsP2mpInstState | 1.3.6.1.4.1.6527.3.1.2.6.25.1.8 | INTEGER | read-only | The value of vRtrMplsP2mpInstState indicates the current working state of this path within this P2MP LSP. |
| vRtrMplsP2mpInstStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.26.1 | not-accessible | Each row entry represents a collection of statistics for a P2MP Labeled Switch Path (LSP) configured for a virtual router in the system. Entries cannot be created and deleted via SNMP SET operations. | |
| NUM vRtrMplsP2mpInstStatLastS2lChange | 1.3.6.1.4.1.6527.3.1.2.6.26.1.2 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatLastS2lChange indicates the time since the last change occurred on this P2MP LSP. |
| NUM vRtrMplsP2mpInstStatLastS2lTimeDown | 1.3.6.1.4.1.6527.3.1.2.6.26.1.6 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatLastS2lTimeDown indicates the total time that this S2l has not been operational. |
| NUM vRtrMplsP2mpInstStatLastS2lTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.26.1.5 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatLastS2lTimeUp indicates the total time that this S2l has been operational. |
| NUM vRtrMplsP2mpInstStatLastTrans | 1.3.6.1.4.1.6527.3.1.2.6.26.1.10 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatLastTrans indicates the time since the last transition occurred on this P2mp instance. |
| G32 vRtrMplsP2mpInstStatOperationalS2ls | 1.3.6.1.4.1.6527.3.1.2.6.26.1.4 | Gauge32 | read-only | The value of vRtrMplsP2mpInstStatOperationalS2ls indicates the number of operational S2ls for this P2MP LSP. This includes the S2ls currently active. |
| C32 vRtrMplsP2mpInstStatS2lChanges | 1.3.6.1.4.1.6527.3.1.2.6.26.1.1 | Counter32 | read-only | The value of vRtrMplsP2mpInstStatS2lChanges indicates the number of S2l changes this P2MP LSP has had. For every S2l change (S2l down, S2l up, S2l change), a corresponding syslog/trap (if enabled) is generated for it. |
| vRtrMplsP2mpInstStatTable | 1.3.6.1.4.1.6527.3.1.2.6.26 | not-accessible | The vRtrMplsP2mpInstStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| NUM vRtrMplsP2mpInstStatTimeDown | 1.3.6.1.4.1.6527.3.1.2.6.26.1.8 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatTimeDown indicates the total time that this P2MP instance has not been operational. |
| NUM vRtrMplsP2mpInstStatTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.26.1.7 | TimeInterval | read-only | The value of vRtrMplsP2mpInstStatTimeUp indicates the total time that this P2MP instance has been operational. |
| C32 vRtrMplsP2mpInstStatTransitions | 1.3.6.1.4.1.6527.3.1.2.6.26.1.9 | Counter32 | read-only | The The value of vRtrMplsP2mpInstStatTransitions indicates the number of state transitions (up -> down and down -> up) this P2mp instance has undergone. |
| vRtrMplsP2mpInstTable | 1.3.6.1.4.1.6527.3.1.2.6.25 | not-accessible | vRtrMplsP2mpInstTable contains configuration information for the Mpls Point to Multipoint (P2MP) Instance on a virtual router. | |
| TIM vRtrMplsP2mpInstTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.24 | TimeStamp | read-only | The value of vRtrMplsP2mpInstTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsP2mpInstTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| INT vRtrMplsP2mpInstType | 1.3.6.1.4.1.6527.3.1.2.6.25.1.5 | INTEGER | read-create | The value of vRtrMplsP2mpInstType specifies the type of P2MP LSP instance. |
| NTF vRtrMplsResignalTimerExpired | 1.3.6.1.4.1.6527.3.1.3.6.0.18 | The vRtrMplsResignalTimerExpired notification is generated when the resignal timer expires for a MPLS instance. Make before break (MBB) would be started only on those P2P LSP (Point to Point) paths that need to be resignaled. vRtrMplsGeneralResignalTimer would be reset once this notification is sent. | ||
| U32 vRtrMplsRsvpSessionIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.7 | Unsigned32 | read-only | An index into the TIMETRA-RSVP-MIB::vRtrRsvpSessionTable identifying a particular RSVP session. |
| U32 vRtrMplsS2lSubGroupId | 1.3.6.1.4.1.6527.3.1.2.6.28.1.10 | Unsigned32 | read-only | The value of vRtrMplsS2lSubGroupId indicates the value which identifies the group for this entry. |
| TMN vRtrMplsS2lSubLspAdminState | 1.3.6.1.4.1.6527.3.1.2.6.28.1.8 | TmnxAdminState | read-create | The value of vRtrMplsS2lSubLspAdminState specifies the desired administrative state for this P2MP S2L sub LSP. |
| C32 vRtrMplsS2lSubLspCspfQueries | 1.3.6.1.4.1.6527.3.1.2.6.29.1.5 | Counter32 | read-only | The value of vRtrMplsS2lSubLspCspfQueries indicates the number of CSPF queries that have been made for this LSP S2l. |
| NTF vRtrMplsS2lSubLspDown | 1.3.6.1.4.1.6527.3.1.3.6.0.12 | This Notification is generated when a S2l sub LSP transitions out of 'inService' state to any other state. | ||
| TIM vRtrMplsS2lSubLspDownTime | 1.3.6.1.4.1.6527.3.1.2.6.28.1.34 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspDownTime indicates the timestamp when the S2l went down. |
| IP vRtrMplsS2lSubLspDstAddr | 1.3.6.1.4.1.6527.3.1.2.6.28.1.2 | InetAddress | not-accessible | The value of vRtrMplsS2lSubLspDstAddr indicates the IP address of the destination address of the S2L sub LSP. |
| IPt vRtrMplsS2lSubLspDstAddrType | 1.3.6.1.4.1.6527.3.1.2.6.28.1.1 | InetAddressType | not-accessible | The value of vRtrMplsS2lSubLspDstAddrType indicates the type of vRtrMplsS2lSubLspDstAddr. |
| vRtrMplsS2lSubLspEntry | 1.3.6.1.4.1.6527.3.1.2.6.28.1 | not-accessible | Each row entry represents an association between a Labeled Switch Path (P2MP LSP) in the vRtrMplsP2mpInstTable and a S2L sub LSP entry in the vRtrMplsS2lSubLspTable. Entries in this table can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrMplsS2lSubLspType to have been assigned a valid value. | |
| TMN vRtrMplsS2lSubLspFailCode | 1.3.6.1.4.1.6527.3.1.2.6.28.1.15 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsS2lSubLspFailCode indicates the reason code for P2MP LSP Path failure. A value of 0 indicates that no failure has occurred. |
| IP vRtrMplsS2lSubLspFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.28.1.17 | InetAddress | read-only | The value of vRtrMplsS2lSubLspFailNodeAddr indicates the IP address of the node in the P2MP S2L sub LSP at which the P2MP S2L sub LSP failed. |
| IPt vRtrMplsS2lSubLspFailNodeArType | 1.3.6.1.4.1.6527.3.1.2.6.28.1.16 | InetAddressType | read-only | The value of vRtrMplsS2lSubLspFailNodeArType indicates type of vRtrMplsS2lSubLspFailNodeAddr. When no failure has occurred, this value is 0. |
| MPL vRtrMplsS2lSubLspId | 1.3.6.1.4.1.6527.3.1.2.6.28.1.11 | MplsLSPID | read-only | The value of vRtrMplsS2lSubLspId indicates the value which identifies the label switched path that is signaled for this entry. |
| T/F vRtrMplsS2lSubLspIsFastRetry | 1.3.6.1.4.1.6527.3.1.2.6.28.1.35 | TruthValue | read-only | The value of vRtrMplsS2lSubLspIsFastRetry indicates which retry timer is being referred to by vRtrMplsS2lSubLspRetryTimeRemain. When the value of vRtrMplsLspPathIsFastRetry is set to 'true', vRtrMplsLspPathRetryTimeRemaining is referring to the P2MP S2L path fast timer, vRtrMplsGenP2mpS2lFastRetry. When the value of vRtrMplsLspPathIsFastRetry is set to 'false', vRtrMplsS2lSubLspRetryTimeRemain is referring to the LSP retry timer, vRtrMplsLspRetryTimer. |
| TIM vRtrMplsS2lSubLspLastChange | 1.3.6.1.4.1.6527.3.1.2.6.28.1.4 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspRowStatus indicates the sysUpTime when this row was last modified. |
| TIM vRtrMplsS2lSubLspLastMBBEnd | 1.3.6.1.4.1.6527.3.1.2.6.28.1.23 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspLastMBBEnd indicates the sysUpTime when the last MBB ended. |
| U32 vRtrMplsS2lSubLspLastMBBMetric | 1.3.6.1.4.1.6527.3.1.2.6.28.1.24 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspLastMBBMetric indicates the cost of the traffic engineered S2L sub LSP for the S2L sub LSP prior to MBB. |
| INT vRtrMplsS2lSubLspLastMBBState | 1.3.6.1.4.1.6527.3.1.2.6.28.1.25 | INTEGER | read-only | The value of vRtrMplsS2lSubLspLastMBBState indicates whether the last Make-before-break was successful or failed. Possible states are: none (1) - no make-before-break invoked success (2) - make-before-break successful fail (3) - make-before-break failed. |
| TMN vRtrMplsS2lSubLspLastMBBType | 1.3.6.1.4.1.6527.3.1.2.6.28.1.22 | TmnxMplsMBBType | read-only | The value of vRtrMplsS2lSubLspLastMBBType indicates the type of last Make-before-break (MBB). If 'none', then no MBB has been attempted. |
| TIM vRtrMplsS2lSubLspLastResigAttpt | 1.3.6.1.4.1.6527.3.1.2.6.28.1.21 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspLastResigAttpt indicates the sysUpTime when the last attempt to resignal this LSP was made. |
| TMN vRtrMplsS2lSubLspMBBFailCode | 1.3.6.1.4.1.6527.3.1.2.6.28.1.30 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsS2lSubLspMBBFailCode indicates the reason code for in-progress MBB failure. A value of 'none' indicates that no failure has occurred. |
| IP vRtrMplsS2lSubLspMBBFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.6.28.1.32 | InetAddress | read-only | The value of vRtrMplsS2lSubLspMBBFailNodeAddr indicates the IP address of the node in the S2L sub LSP at which the in-progress MBB failed. A value of 'unknown' for vRtrMplsS2lSubLspMBBFailNodeType and empty string for vRtrMplsS2lSubLspMBBFailNodeAddr indicates that no failure has occurred. |
| IPt vRtrMplsS2lSubLspMBBFailNodeType | 1.3.6.1.4.1.6527.3.1.2.6.28.1.31 | InetAddressType | read-only | The value of vRtrMplsS2lSubLspMBBFailNodeType indicates the type of vRtrMplsS2lSubLspMBBFailNodeAddr. A value of 'unknown' indicates that no failure has occurred. |
| U32 vRtrMplsS2lSubLspMBBNextRetry | 1.3.6.1.4.1.6527.3.1.2.6.28.1.28 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspMBBNextRetry indicates the amount of time remaining in seconds before the next attempt is made to retry the in-progress MBB. |
| U32 vRtrMplsS2lSubLspMBBRetryAttpts | 1.3.6.1.4.1.6527.3.1.2.6.28.1.29 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspMBBRetryAttpts indicates 'n' where nth attempt for the MBB is in progress. |
| TIM vRtrMplsS2lSubLspMBBStarted | 1.3.6.1.4.1.6527.3.1.2.6.28.1.27 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspMBBStarted indicates the sysUpTime when the in-progress MBB started. |
| U32 vRtrMplsS2lSubLspMBBTimeoutIn | 1.3.6.1.4.1.6527.3.1.2.6.28.1.37 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspMBBTimeoutIn specifies the amount of time remaining, in seconds, for the in-progress S2L MBB path state to time out after the initial PATH message has been sent. If the timer expires and the in-progress S2L MBB path has not become operationally up, the S2L MBB path is torn down and the retry timer is started to schedule a new retry cycle. |
| TMN vRtrMplsS2lSubLspMBBTypeInProg | 1.3.6.1.4.1.6527.3.1.2.6.28.1.26 | TmnxMplsMBBType | read-only | The value of vRtrMplsS2lSubLspMBBTypeInProg indicates the type of the Make-before-break (MBB) that is in progress. If 'none', then no MBB is in progress. |
| U32 vRtrMplsS2lSubLspNegotiatedMTU | 1.3.6.1.4.1.6527.3.1.2.6.28.1.14 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspNegotiatedMTU indicates the size for the Maximum transmission unit (MTU) that is negotiated during establishment of this P2MP LSP Path. |
| IP vRtrMplsS2lSubLspNtDstAddr | 1.3.6.1.4.1.6527.3.1.2.6.16.7 | InetAddress | accessible-for-notify | The value of vRtrMplsS2lSubLspDstAddr indicates the IP address of the destination address of the S2L sub LSP. |
| IPt vRtrMplsS2lSubLspNtDstAddrType | 1.3.6.1.4.1.6527.3.1.2.6.16.6 | InetAddressType | accessible-for-notify | The value of vRtrMplsS2lSubLspDstAddrType indicates the type of vRtrMplsS2lSubLspDstAddr. |
| I32 vRtrMplsS2lSubLspOperBandwidth | 1.3.6.1.4.1.6527.3.1.2.6.28.1.18 | Integer32 | read-only | The value of vRtrMplsS2lSubLspOperBandwidth indicates the amount of bandwidth in mega-bits per seconds (Mbps) that has been reserved for the operational P2MP S2L sub LSP. When make-before-break functionality for the P2MP LSP is enabled and if the S2L sub LSP bandwidth is changed, the resources allocated to the existing P2MP LSP paths will not be released until a new S2L sub LSP with the new bandwidth settings has been established. While a new S2L sub LSP is being signaled, the administrative value and the operational values of the S2L sub LSP bandwidth may differ. The value of vRtrMplsS2lSubLspOperBandwidth specifies the bandwidth requirements for the new P2MP S2L sub LSP trying to be established whereas the value of vRtrMplsS2lSubLspOperBandwidth specifies the bandwidth reserved for the existing P2MP S2L sub LSP. |
| U32 vRtrMplsS2lSubLspOperMTU | 1.3.6.1.4.1.6527.3.1.2.6.28.1.20 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspOperMTU indicates the size for the Maximum transmission unit (MTU) that is currently operation for this P2MP LSP Path. |
| TMN vRtrMplsS2lSubLspOperState | 1.3.6.1.4.1.6527.3.1.2.6.28.1.9 | TmnxOperState | read-only | The value of vRtrMplsS2lSubLspAdminState indicates the current operational state of this P2MP S2L sub LSP. |
| BIT vRtrMplsS2lSubLspProperties | 1.3.6.1.4.1.6527.3.1.2.6.28.1.6 | Bits | read-only | The value of vRtrMplsS2lSubLspProperties indicates the set of configured properties. For example, if the S2L sub LSP is an adaptive S2L sub LSP, the bit corresponding to bit value 1 is set. |
| NTF vRtrMplsS2lSubLspRerouted | 1.3.6.1.4.1.6527.3.1.3.6.0.13 | The vRtrMplsS2lSubLspRerouted notification is generated when an S2l sub LSP is rerouted. | ||
| NTF vRtrMplsS2lSubLspResignaled | 1.3.6.1.4.1.6527.3.1.3.6.0.14 | The vRtrMplsS2lSubLspResignaled notification is generated when an S2l sub LSP is resignaled. The vRtrMplsS2lSubLspLastMBBType indicates the reason why the S2l sub LSP was resignaled. | ||
| C32 vRtrMplsS2lSubLspRetryAttempts | 1.3.6.1.4.1.6527.3.1.2.6.29.1.3 | Counter32 | read-only | The value of vRtrMplsS2lSubLspRetryAttempts indicates the number of unsuccessful attempts which have been made to signal this S2l. As soon as the S2l gets signalled, this is set to 0. |
| U32 vRtrMplsS2lSubLspRetryTimeRemain | 1.3.6.1.4.1.6527.3.1.2.6.28.1.12 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspRetryTimeRemain indicates the time to signal this S2L sub LSP. |
| ROW vRtrMplsS2lSubLspRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.28.1.3 | RowStatus | read-create | The value of vRtrMplsS2lSubLspRowStatus specifies row status used for creation, deletion, or control of vRtrMplsLspPathTable entries. Before the row can be placed into the 'active' state vRtrMplsS2lSubLspType must have been assigned a valid value. |
| INT vRtrMplsS2lSubLspState | 1.3.6.1.4.1.6527.3.1.2.6.28.1.7 | INTEGER | read-only | The value of vRtrMplsS2lSubLspState indicates the current working state of this S2L sub LSP within this LSP. |
| vRtrMplsS2lSubLspStatEntry | 1.3.6.1.4.1.6527.3.1.2.6.29.1 | not-accessible | Each row entry represents a collection of statistics for a P2MP Source to Leaf (S2L) Sub Labeled Switch Path (LSP) configured for a i virtual router in the system. Entries cannot be created and deleted via SNMP SET operations. | |
| vRtrMplsS2lSubLspStatTable | 1.3.6.1.4.1.6527.3.1.2.6.29 | not-accessible | The vRtrMplsS2lSubLspStatTable has an entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| vRtrMplsS2lSubLspTable | 1.3.6.1.4.1.6527.3.1.2.6.28 | not-accessible | The vRtrMplsS2lSubLspTable provides an association between an P2MP LSP and a source to leaf (S2L) sub LSP path called as S2L here. A P2MP LSP can have more than one S2L sub LSP association. | |
| TIM vRtrMplsS2lSubLspTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.27 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsS2lSubLspTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| NUM vRtrMplsS2lSubLspTimeDown | 1.3.6.1.4.1.6527.3.1.2.6.29.1.2 | TimeInterval | read-only | The value of vRtrMplsS2lSubLspTimeUp indicates the total time that this LSP S2l has not been operational. |
| U32 vRtrMplsS2lSubLspTimeoutIn | 1.3.6.1.4.1.6527.3.1.2.6.28.1.36 | Unsigned32 | read-only | The value of vRtrMplsS2lSubLspTimeoutIn specifies the amount of time remaining, in seconds, for the S2L path state to time out after the initial PATH message has been sent. If the timer expires and the S2L path has not become operationally up, the S2L path is torn down and the retry timer is started to schedule a new retry cycle. |
| NUM vRtrMplsS2lSubLspTimeUp | 1.3.6.1.4.1.6527.3.1.2.6.29.1.1 | TimeInterval | read-only | The value of vRtrMplsS2lSubLspTimeUp indicates the total time that this LSP S2l has been operational. For example, the percentage up time can be determined by computing (vRtrMplsS2lSubLspTimeUp/vRtrMplsLspAge * 100 %). |
| C32 vRtrMplsS2lSubLspTransitionCount | 1.3.6.1.4.1.6527.3.1.2.6.29.1.4 | Counter32 | read-only | The value of vRtrMplsS2lSubLspTransitionCount indicates the number of transitions that have occurred for this LSP. |
| I32 vRtrMplsS2lSubLspTunARHopLtIndex | 1.3.6.1.4.1.6527.3.1.2.6.28.1.13 | Integer32 | read-only | The value of vRtrMplsS2lSubLspTunARHopLtIndex indicates Primary index into the mplsTunnelARHopTable identifying a particular recorded hop list. A value of 0 implies that there is no recored hop list associated with this P2MP LSP path. |
| I32 vRtrMplsS2lSubLspTunCRHopLtIndex | 1.3.6.1.4.1.6527.3.1.2.6.28.1.19 | Integer32 | read-only | The value of vRtrMplsS2lSubLspTunCRHopLtIndex indicates primary index into the vRtrMplsTunnelCHopTable identifying a particular computed hop list. A value of 0 implies that there is no computed hop list associated with this LSP path. |
| INT vRtrMplsS2lSubLspType | 1.3.6.1.4.1.6527.3.1.2.6.28.1.5 | INTEGER | read-only | The value of vRtrMplsS2lSubLspRowStatus indicates the value that represents the role this S2L sub LSP is taking within this P2MP LSP. |
| NTF vRtrMplsS2lSubLspUp | 1.3.6.1.4.1.6527.3.1.3.6.0.11 | This Notification is generated when a S2l sub LSP transitions to the 'inService' state from any other state. | ||
| TIM vRtrMplsS2lSubLspUpTime | 1.3.6.1.4.1.6527.3.1.2.6.28.1.33 | TimeStamp | read-only | The value of vRtrMplsS2lSubLspUpTime indicates the timestamp when the S2l came up. |
| vRtrMplsSrlgDBIfEntry | 1.3.6.1.4.1.6527.3.1.2.6.33.1 | not-accessible | Each row entry represents an SRLG group associated with a interface which is validated as part of a router ID in the routing table. A row can be created or deleted via SNMP SET requests. | |
| IP vRtrMplsSrlgDBIfIntIpAddr | 1.3.6.1.4.1.6527.3.1.2.6.33.1.2 | InetAddress | not-accessible | The value of vRtrMplsSrlgDBIfIntIpAddr indicates the IP address of the interface. |
| IPt vRtrMplsSrlgDBIfIntIpAddrType | 1.3.6.1.4.1.6527.3.1.2.6.33.1.1 | InetAddressType | not-accessible | The value of vRtrMplsSrlgDBIfIntIpAddrType indicates the type of vRtrMplsSrlgDBIfIntIpAddr. |
| TIM vRtrMplsSrlgDBIfLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.33.1.5 | TimeStamp | read-only | The value of vRtrMplsSrlgDBIfLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgDBIfTable. |
| ROW vRtrMplsSrlgDBIfRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.33.1.4 | RowStatus | read-create | vRtrMplsSrlgDBIfRowStatus is used to create, delete or control entries in the vRtrMplsSrlgDBIfTable. |
| TNA vRtrMplsSrlgDBIfSrlgGroupName | 1.3.6.1.4.1.6527.3.1.2.6.33.1.3 | TNamedItem | not-accessible | The value of vRtrMplsSrlgDBIfSrlgGroupName indicates the SRLG group name. |
| vRtrMplsSrlgDBIfTable | 1.3.6.1.4.1.6527.3.1.2.6.33 | not-accessible | The vRtrMplsSrlgDBIfTable has an entry for each Shared Risk Link Group (SRLG) groups associated with a interface which is validated as part of a router ID in the routing table. The user manually enters the SRLG membership information for any link in the network, into the user SRLG database. | |
| TIM vRtrMplsSrlgDBIfTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.32 | TimeStamp | read-only | The value of vRtrMplsSrlgDBIfTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgDBIfTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TMN vRtrMplsSrlgDBRtrIdAdminState | 1.3.6.1.4.1.6527.3.1.2.6.31.1.3 | TmnxAdminState | read-create | The value of vRtrMplsSrlgDBRtrIdAdminState specifies the desired administrative state for the router-id entry in the vRtrMplsSrlgDBRtrIdTable. |
| vRtrMplsSrlgDBRtrIdEntry | 1.3.6.1.4.1.6527.3.1.2.6.31.1 | not-accessible | Each row entry represents a router ID under which interface entries would be configured for the SRLG database table. A row can be created or deleted via SNMP SET requests. | |
| TIM vRtrMplsSrlgDBRtrIdLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.31.1.4 | TimeStamp | read-only | The value of vRtrMplsSrlgDBRtrIdLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgDBRtrIdTable. |
| TMN vRtrMplsSrlgDBRtrIdRouterID | 1.3.6.1.4.1.6527.3.1.2.6.31.1.1 | TmnxMplsRouterId | not-accessible | The value of vRtrMplsSrlgDBRtrIdRouterID specifies a 32-bit integer uniquely identifying the router in the Autonomous System. By convention to ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router. The router-id can be either the local one or some remote router. |
| ROW vRtrMplsSrlgDBRtrIdRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.31.1.2 | RowStatus | read-create | vRtrMplsSrlgDBRtrIdRowStatus is used to create, delete or control entries in the vRtrMplsSrlgDBRtrIdTable. |
| vRtrMplsSrlgDBRtrIdTable | 1.3.6.1.4.1.6527.3.1.2.6.31 | not-accessible | The vRtrMplsSrlgDBRtrIdTable has an entry for each router-id configured under user Shared Risk Link Group (SRLG) database. The user manually enters the SRLG membership information for any link in the network, into the user SRLG database. | |
| TIM vRtrMplsSrlgDBRtrIdTblLastChg | 1.3.6.1.4.1.6527.3.1.2.6.30 | TimeStamp | read-only | The value of vRtrMplsSrlgDBRtrIdTblLastChg indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgDBRtrIdTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrMplsSrlgGrpEntry | 1.3.6.1.4.1.6527.3.1.2.6.21.1 | not-accessible | Each row entry represents a SRLG group on this virtual router that participates in the MPLS protocol. A row can be created or deleted via SNMP SET requests. | |
| TIM vRtrMplsSrlgGrpLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.21.1.3 | TimeStamp | read-only | The value of vRtrMplsSrlgGrpLastChanged indicates the timestamp of last change to this row in vRtrMplsSrlgGrpTable. |
| TNA vRtrMplsSrlgGrpName | 1.3.6.1.4.1.6527.3.1.2.6.21.1.1 | TNamedItem | not-accessible | The value of vRtrMplsSrlgGrpName indicates the SRLG group name. |
| ROW vRtrMplsSrlgGrpRowStatus | 1.3.6.1.4.1.6527.3.1.2.6.21.1.2 | RowStatus | read-create | vRtrMplsSrlgGrpRowStatus is used to create, delete or control entries in the vRtrMplsSrlgGrpTable. A value must also be set for vRtrMplsSrlgGrpValue before the row entry can transition to the 'active' state. |
| vRtrMplsSrlgGrpTable | 1.3.6.1.4.1.6527.3.1.2.6.21 | not-accessible | The vRtrMplsSrlgGrpTable has an entry for each Shared Risk Link Groups (SRLG) group configured for MPLS in the system. | |
| TIM vRtrMplsSrlgGrpTableLastChanged | 1.3.6.1.4.1.6527.3.1.2.6.20 | TimeStamp | read-only | The value of vRtrMplsSrlgGrpTableLastChanged indicates the sysUpTime at the time of the last modification to vRtrMplsSrlgGrpTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| U32 vRtrMplsSrlgGrpValue | 1.3.6.1.4.1.6527.3.1.2.6.21.1.4 | Unsigned32 | read-create | The value of vRtrMplsSrlgGrpValue specifies the group value associated with vRtrMplsSrlgGrpName. This value is unique within a virtual router instance. At the time of row creation, a value for vRtrMplsSrlgGrpValue must be specified or else row creation would fail. |
| NTF vRtrMplsStateChange | 1.3.6.1.4.1.6527.3.1.3.6.0.1 | This Notification is generated when the MPLS module changes state | ||
| MPL vRtrMplsStaticLSPLabel | 1.3.6.1.4.1.6527.3.1.2.6.18.1.1 | MplsLabel | not-accessible | The value of vRtrMplsStaticLSPLabel specifies the label value for a static LSP. The range of vRtrMplsStaticLSPLabel is dynamic and depends on the value of vRtrMplsLabelMaxStaticLspLabels. If vRtrMplsLabelMaxStaticLspLabels is 0, static LSP labels cannot be configured. If vRtrMplsLabelMaxStaticLspLabels is 1, vRtrMplsStaticLSPLabel can only be 32. The normal range of vRtrMplsStaticLSPLabel starts at 32 and ends at the value of vRtrMplsLabelMaxStaticLspLabels. |
| vRtrMplsStaticLSPLabelEntry | 1.3.6.1.4.1.6527.3.1.2.6.18.1 | not-accessible | Each row entry in the vRtrMplsStaticLSPLabelTable represents a label of type static LSP that is currently allocated. The entry includes information about the current owner for that label. | |
| TMN vRtrMplsStaticLSPLabelOwner | 1.3.6.1.4.1.6527.3.1.2.6.18.1.2 | TmnxMplsLabelOwner | read-only | The value of vRtrMplsStaticLSPLabelOwner specifies the owner for the label value vRtrMplsStaticLSPLabel. |
| vRtrMplsStaticLSPLabelTable | 1.3.6.1.4.1.6527.3.1.2.6.18 | not-accessible | The vRtrMplsStaticLSPLabelTable has an entry for each allocated label that is part of the static LSP label range. This is a read-only table. | |
| MPL vRtrMplsStaticSvcLabel | 1.3.6.1.4.1.6527.3.1.2.6.19.1.1 | MplsLabel | not-accessible | The value of vRtrMplsStaticSvcLabel specifies the label value for a static SVC. The range of vRtrMplsStaticSvcLabel is dynamic and depends on the value of vRtrMplsLabelMaxStaticLspLabels and vRtrMplsLabelMaxStaticSvcLabels. If vRtrMplsLabelMaxStaticSvcLabels is 0, static SVC labels cannot be configured. The range for vRtrMplsStaticSvcLabel starts at 32 + vRtrMplsLabelMaxStaticLspLabels and ends at 32 + vRtrMplsLabelMaxStaticSvcLabels + vRtrMplsLabelMaxStaticSvcLabels. |
| vRtrMplsStaticSvcLabelEntry | 1.3.6.1.4.1.6527.3.1.2.6.19.1 | not-accessible | Each row entry in the vRtrMplsStaticSvcLabelTable represents a label of type static-svc that is currently allocated. The entry includes information about the current owner for that label. | |
| TMN vRtrMplsStaticSvcLabelOwner | 1.3.6.1.4.1.6527.3.1.2.6.19.1.2 | TmnxMplsLabelOwner | read-only | The value of vRtrMplsStaticSvcLabelOwner specifies the owner for the label value vRtrMplsStaticSvcLabel. |
| vRtrMplsStaticSvcLabelTable | 1.3.6.1.4.1.6527.3.1.2.6.19 | not-accessible | The vRtrMplsStaticSvcLabelTable has an entry for each allocated label that is part of the static service label range. This is a read-only table. | |
| vRtrMplsTunnelARHopEntry | 1.3.6.1.4.1.6527.3.1.2.6.11.1 | not-accessible | A row entry in this table corresponds to a row entry in the mplsTunnelARHopTable and adds to the information contained in that table | |
| BIT vRtrMplsTunnelARHopProtection | 1.3.6.1.4.1.6527.3.1.2.6.11.1.1 | Bits | read-only | If the 'localAvailable' bit is set, it indicates that the link downstream of this node has been protected by means of a local repair mechanism. This mechanism can be either the one-to-one backup method or the facility backup method. If the 'localInUse' bit is set, then it indicates that the local protection mechanism is being used to maintain this tunnel. If the 'bandwidthProtected' bit is set, then it indicates that the backup path is guaranteed to provide the desired bandwidth. If the 'nodeProtected' bit is set, then it indicates that the backup path provides protection against the failure of the next LSR along the LSP. If the 'nodeId' bit is set, it indicates that the address specified in the Record Route Object's IPv4 or IPv6 sub-object is a node-id address. |
| MPL vRtrMplsTunnelARHopRecordLabel | 1.3.6.1.4.1.6527.3.1.2.6.11.1.2 | MplsLabel | read-only | If label recording is enabled, vRtrMplsTunnelARHopRecordLabel specifies the label that is advertised to the previous hop in the hop list. If label recording is disabled, vRtrMplsTunnelARHopRecordLabel will have a value of 4294967295 |
| IP vRtrMplsTunnelARHopRouterId | 1.3.6.1.4.1.6527.3.1.2.6.11.1.3 | IpAddress | read-only | vRtrMplsTunnelARHopRouterId specifies the router ID of the node corresponding to this hop. |
| vRtrMplsTunnelARHopTable | 1.3.6.1.4.1.6527.3.1.2.6.11 | not-accessible | The vRtrMplsTunnelARHopTable augments the mplsTunnelARHopEntry in the MPLS-TE-MIB. | |
| INT vRtrMplsTunnelCHopAddrType | 1.3.6.1.4.1.6527.3.1.2.6.12.1.3 | INTEGER | read-only | Denotes the address type of this tunnel hop. |
| INT vRtrMplsTunnelCHopAsNumber | 1.3.6.1.4.1.6527.3.1.2.6.12.1.8 | INTEGER | read-only | If vRtrMplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact. |
| vRtrMplsTunnelCHopEntry | 1.3.6.1.4.1.6527.3.1.2.6.12.1 | not-accessible | An entry in this table represents a CSPF tunnel hop. Entries are created and deleted by the system. | |
| I32 vRtrMplsTunnelCHopIndex | 1.3.6.1.4.1.6527.3.1.2.6.12.1.2 | Integer32 | not-accessible | Secondary index into this table identifying a particular hop. |
| IP vRtrMplsTunnelCHopIpv4Addr | 1.3.6.1.4.1.6527.3.1.2.6.12.1.4 | IpAddress | read-only | If vRtrMplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contain a value of 0. |
| INT vRtrMplsTunnelCHopIpv4PrefixLen | 1.3.6.1.4.1.6527.3.1.2.6.12.1.5 | INTEGER | read-only | If vRtrMplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0. |
| ADR vRtrMplsTunnelCHopIpv6Addr | 1.3.6.1.4.1.6527.3.1.2.6.12.1.6 | InetAddressIPv6 | read-only | If the vRtrMplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0. |
| INT vRtrMplsTunnelCHopIpv6PrefixLen | 1.3.6.1.4.1.6527.3.1.2.6.12.1.7 | INTEGER | read-only | If vRtrMplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0. |
| I32 vRtrMplsTunnelCHopListIndex | 1.3.6.1.4.1.6527.3.1.2.6.12.1.1 | Integer32 | not-accessible | Primary index into this table identifying a particular explicit route object. |
| MPL vRtrMplsTunnelCHopLspId | 1.3.6.1.4.1.6527.3.1.2.6.12.1.9 | MplsLSPID | read-only | If vRtrMplsTunnelCHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled through this hop (using label stacking). This object is otherwise insignificant and should contain a value of 0 to indicate this fact. |
| INT vRtrMplsTunnelCHopStrictOrLoose | 1.3.6.1.4.1.6527.3.1.2.6.12.1.10 | INTEGER | read-only | Denotes whether this tunnel hop is routed in a strict or loose fashion. |
| vRtrMplsTunnelCHopTable | 1.3.6.1.4.1.6527.3.1.2.6.12 | not-accessible | The vRtrMplsTunnelCHopTable is used to hold the CSPF path for a detour LSP. Each entry indicates a single hop. Primary index is the vRtrMplsTunnelCHopListIndex which associates multiple entries (hops) in the vRtrMplsTunnelCHopTable to a single mplsTunnelEntry specified in the mplsTunnelTable. The first row in the table is the first hop after the origination point of the tunnel. | |
| NTF vRtrMplsXCBundleChange | 1.3.6.1.4.1.6527.3.1.3.6.0.22 | [CAUSE] vRtrMplsXCBundleChange is generated when one or more RSVP sessions changed the state and retained the changed state for entire quiet interval of 2 minutes or till it reaches the maximum interval of 10 minutes if the state of RSVP sessions kept on changing during this period of multiple quiet intervals. [EFFECT] RSVP sessions represented by bits in vRtrMplsXCNotifRednIndicesBitMap changed state on this router instance. [RECOVERY] There is no recovery required for this notification. | ||
| I32 vRtrMplsXCCHopTableIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.9 | Integer32 | read-only | Index to the vRtrMplsTunnelCHopTable entries that specify the hops for the CSPF path for a detour LSP for this tunnel. |
| vRtrMplsXCEntry | 1.3.6.1.4.1.6527.3.1.2.6.6.1 | not-accessible | An entry in this table represents the indices to be used to search the mplsXCTable. | |
| TMN vRtrMplsXCFailCode | 1.3.6.1.4.1.6527.3.1.2.6.6.1.8 | TmnxMplsLspFailCode | read-only | The value of vRtrMplsXCFailCode specifies the reason code for cross-connect failure. A value of 0 indicates that no failure occurred. |
| I32 vRtrMplsXCIndex | 1.3.6.1.4.1.6527.3.1.2.6.6.1.1 | Integer32 | read-only | An index of the mplsXCTable. It represents mplsXCIndex, a field of the mplsXCTable. |
| OCT vRtrMplsXCNotifRednIndicesBitMap | 1.3.6.1.4.1.6527.3.1.2.6.16.15 | OCTET STRING | accessible-for-notify | The value of vRtrMplsXCNotifRednIndicesBitMap indicates the RSVP sessions that either changed state and retained the changed state for the entire quiet interval of 2 minutes or the RSVP sessions that changed state during multiple intervals until a maximum interval of 10 minutes has elapsed. Each bit location in vRtrMplsXCNotifRednIndicesBitMap corresponds to a created or deleted row entry in vRtrMplsXCTable as identified by the value of vRtrMplsXCIndex. This index is same as the value of TIMETRA-RSVP-MIB::vRtrRsvpSessionIndex which corresponds to a created or deleted RSVP session entry in TIMETRA-RSVP-MIB::vRtrRsvpSessionTable. The value of vRtrMplsXCNotifyRednStartIndex indicates the index value of the first affected row entry represented by bit 0, the most significant bit. If the value of vRtrMplsXCNotifyRednBundlingType is set to 'create (2)', all the bits set in vRtrMplsXCNotifRednIndicesBitMap represent created RSVP sessions. If the value of vRtrMplsXCNotifyRednBundlingType is set to 'delete (1)', all the bits set in vRtrMplsXCNotifRednIndicesBitMap represent deleted RSVP sessions. |
| INT vRtrMplsXCNotifyRednBundlingType | 1.3.6.1.4.1.6527.3.1.2.6.16.16 | INTEGER | accessible-for-notify | The value of vRtrMplsXCNotifyRednBundlingType indicates whether this notification is generated for deletion or creation of RSVP sessions on this ingress, transit or egress router instance. |
| U32 vRtrMplsXCNotifyRednEndIndex | 1.3.6.1.4.1.6527.3.1.2.6.16.19 | Unsigned32 | accessible-for-notify | The value of vRtrMplsXCNotifyRednEndIndex indicates which vRtrMplsXCIndex is represented by the last bit in vRtrMplsXCNotifRednIndicesBitMap. The value vRtrMplsXCNotifyRednEndIndex can be useful for a sanity check of vRtrMplsXCNotifyRednNumOfBitsSet. vRtrMplsXCNotifyRednNumOfBitsSet. = (vRtrMplsXCNotifyRednEndIndex - vRtrMplsXCNotifyRednStartIndex + 1). |
| U32 vRtrMplsXCNotifyRednNumOfBitsSet | 1.3.6.1.4.1.6527.3.1.2.6.16.17 | Unsigned32 | accessible-for-notify | The value of vRtrMplsXCNotifyRednNumOfBitsSet indicates the total number of bits set in vRtrMplsXCNotifRednIndicesBitMap. |
| U32 vRtrMplsXCNotifyRednStartIndex | 1.3.6.1.4.1.6527.3.1.2.6.16.18 | Unsigned32 | accessible-for-notify | The value of vRtrMplsXCNotifyRednStartIndex indicates which vRtrMplsXCIndex is represented by the first bit in vRtrMplsXCNotifRednIndicesBitMap. |
| vRtrMplsXCTable | 1.3.6.1.4.1.6527.3.1.2.6.6 | not-accessible | This table has an entry for each mplsXCEntry in the mplsXCTable. It serves as an another indirect index to the mplsXCTable. |
RFC description
Manages and provisions MPLS extensions for Alcatel-Lucent SROS devices including LSP configuration, tunneling, and routing.
Start monitoring Alcatel-Lucent/Nokia SROS service router (7x50/SR series) (MPLS LSP admin/oper status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.