RAD-HDLC-MIB

All MIBs › RAD-HDLC-MIB

Description: RAD Data Communications HDLC serial interface MIB managing protocol type, clock source, loopback, and line-rate settings for V.35, X.21, and RS-530 WAN links

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RAD-HDLC-MIB?

RAD-HDLC-MIB is a RAD Data Communications proprietary MIB configuring and monitoring HDLC (High-level Data Link Control) WAN interfaces. Its configuration table, keyed by interface, records protocol, rate resolution, TX clock source/polarity, terminal mode, loopback state, flow control, line rate, RX clock mode/polarity, and loss-of-frame flag, a current-status table records operational status, LOF, inbound/outbound frames, inbound errors, aborted frames, and length errors, and an interval table extends the same over historical windows. As a configuration/performance MIB it lets an administrator confirm HDLC line-rate/clocking settings and watch frame-error trends on a RAD Data Communications device. It is deployed on RAD Data Communications HDLC WAN access equipment. Engineers can download the RAD-HDLC-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAD-HDLC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

RAD Data Communications HDLC WAN access equipment

Monitoring Examples

An administrator checks hdlcCurrentInErrors and hdlcCurrentAbortedFrames to diagnose a degraded HDLC WAN link on a RAD Data Communications device.

What Can Be Monitored

HDLC line configuration and frame-error statistics

Imported Objects

From IF-MIB

InterfaceIndex

From RAD-MIB

diverseIfWanGen	OBJECT-IDENTITY
fileName	OBJECT-TYPE
radAtm	OBJECT-IDENTITY
radRouter	OBJECT-IDENTITY
radSysRtrEvents	OBJECT-IDENTITY
rtrBridge	OBJECT-IDENTITY

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using hdlcLOF OID:

Select a RAD Data Communications HDLC WAN access equipment as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hdlcLOF into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the total number of seconds the port is in Loss Of Frame state. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hdlcMibObjects	1.3.6.1.4.1.164.3.1.6.5
hdlcTable	1.3.6.1.4.1.164.3.1.6.5.1		not-accessible	The HDLC configuration table.
hdlcEntry	1.3.6.1.4.1.164.3.1.6.5.1.1		not-accessible	Defines the contents of each line in the RAD HDLC Table.
INT hdlcProtocol	1.3.6.1.4.1.164.3.1.6.5.1.1.1	INTEGER	read-write	The HDLC protocol type V35 - HDLC encapsulated over V35 X21 - HDLC encapsulated over X21 RS530 - HDLC encapsulated over RS530
INT hdlcRateResolution	1.3.6.1.4.1.164.3.1.6.5.1.1.2	INTEGER	read-write	The baud rate of the internal clock.
INT hdlcTxClockSource	1.3.6.1.4.1.164.3.1.6.5.1.1.3	INTEGER	read-write	The baud rate of the internal clock.
INT hdlcTerminalMode	1.3.6.1.4.1.164.3.1.6.5.1.1.4	INTEGER	read-write	.
INT hdlcLoopbackState	1.3.6.1.4.1.164.3.1.6.5.1.1.5	INTEGER	read-write	internal - All data coming from the network port is looped back external - All data comming from the line is looped back.
INT hdlcTxClockPolarity	1.3.6.1.4.1.164.3.1.6.5.1.1.6	INTEGER	read-write	normal - The transmitted data is sampled at the middle of bit time inverse - The transmitted data is sampled at the end of the bit time (high data rate/long cable).
INT hdlcFlowControl	1.3.6.1.4.1.164.3.1.6.5.1.1.7	INTEGER	read-write	Enable/Disable the CTS/RTS flow control signals.
I32 hdlcLineRate	1.3.6.1.4.1.164.3.1.6.5.1.1.8	Integer32	read-write	The rate values for HDLC are n*56/64Kbps, where 1<=n<=32, 64, 128 and the following values: 1544, 3088, 6176. The rate values for HSSI is nMbps, where 1<=n<=52.
INT hdlcRxClockMode	1.3.6.1.4.1.164.3.1.6.5.1.1.9	INTEGER	read-write	.
G32 hdlcLOFEx	1.3.6.1.4.1.164.3.1.6.5.1.1.10	Gauge32	read-only	Total number of seconds the port is in Loss Of Frame state.
INT hdlcRxClockPolarity	1.3.6.1.4.1.164.3.1.6.5.1.1.11	INTEGER	read-write	normal - The received data is sampled at the middle of bit time inverse - The received data is sampled at the end of the bit time (high data rate/long cable).
hdlcPerformance	1.3.6.1.4.1.164.3.1.6.5.2
hdlcCurrentTable	1.3.6.1.4.1.164.3.1.6.5.2.1		not-accessible	The HDLC Current table.
hdlcCurrentEntry	1.3.6.1.4.1.164.3.1.6.5.2.1.1		not-accessible	An entry in the HDLC Current table.
I32 hdlcCurrentIfIndex	1.3.6.1.4.1.164.3.1.6.5.2.1.1.1	Integer32	read-only	The index of the HDLC interface. It may be ifIndex.
OCT hdlcCurrentStatus	1.3.6.1.4.1.164.3.1.6.5.2.1.1.2	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
G32 hdlcCurrentLOF	1.3.6.1.4.1.164.3.1.6.5.2.1.1.3	Gauge32	read-only	The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by the HDLC interface in the current 15 minute interval.
G32 hdlcCurrentInFrames	1.3.6.1.4.1.164.3.1.6.5.2.1.1.4	Gauge32	read-only	The counter associated with the number of received frames, encountered by the HDLC interface in the current 15 minute interval.
G32 hdlcCurrentInErrors	1.3.6.1.4.1.164.3.1.6.5.2.1.1.5	Gauge32	read-only	The counter associated with the number of Errored received frames, encountered by the HDLC interface in the current 15 minute interval.
G32 hdlcCurrentOutFrames	1.3.6.1.4.1.164.3.1.6.5.2.1.1.6	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the HDLC interface in the current 15 minute interval.
G32 hdlcCurrentAbortedFrames	1.3.6.1.4.1.164.3.1.6.5.2.1.1.7	Gauge32	read-only	The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in the current 15 minute interval.
G32 hdlcCurrentLengthError	1.3.6.1.4.1.164.3.1.6.5.2.1.1.8	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the HDLC interface in the current 15 minute interval.
hdlcIntervalTable	1.3.6.1.4.1.164.3.1.6.5.2.2		not-accessible	The HDLC Interval table.
hdlcIntervalEntry	1.3.6.1.4.1.164.3.1.6.5.2.2.1		not-accessible	An entry in the HDLC Interval table.
I32 hdlcIntervalIfIndex	1.3.6.1.4.1.164.3.1.6.5.2.2.1.1	Integer32	read-only	The index of the HDLC interface. It may be ifIndex.
I32 hdlcIntervalNumber	1.3.6.1.4.1.164.3.1.6.5.2.2.1.2	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
OCT hdlcIntervalStatus	1.3.6.1.4.1.164.3.1.6.5.2.2.1.3	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
G32 hdlcIntervalLOF	1.3.6.1.4.1.164.3.1.6.5.2.2.1.4	Gauge32	read-only	The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by an HDLC interface in one of the previous 96, individual 15 minute, intervals.
G32 hdlcIntervalInFrames	1.3.6.1.4.1.164.3.1.6.5.2.2.1.5	Gauge32	read-only	The counter associated with the number of received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
G32 hdlcIntervalInErrors	1.3.6.1.4.1.164.3.1.6.5.2.2.1.6	Gauge32	read-only	The counter associated with the number of Errored received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
G32 hdlcIntervalOutFrames	1.3.6.1.4.1.164.3.1.6.5.2.2.1.7	Gauge32	read-only	The counter associated with the number of transmitted frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
G32 hdlcIntervalAbortedFrames	1.3.6.1.4.1.164.3.1.6.5.2.2.1.8	Gauge32	read-only	The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
G32 hdlcIntervalLengthError	1.3.6.1.4.1.164.3.1.6.5.2.2.1.9	Gauge32	read-only	The counter associated with the number of received frames with length error, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals.
NTF rtrFACSViolation	1.3.6.1.4.1.164.6.1.11.0.1			The trap is sent for every violation of a FACS filter.
NTF rtrSwDwnLoadTrap	1.3.6.1.4.1.164.6.1.11.0.2			The trap is sent after the tftp download of the software and before the decompression and reset operations.
rtrInterfaces	1.3.6.1.4.1.164.11.1
rtrConfigIfTable	1.3.6.1.4.1.164.11.1.1		not-accessible	Table of configured interfaces.
rtrConfigIfEntry	1.3.6.1.4.1.164.11.1.1.1		not-accessible	Each entry defines a configured interface.
NUM rtrConfigIfIndex	1.3.6.1.4.1.164.11.1.1.1.1	InterfaceIndex	read-only	This variable uniquely identifies the interface. It is used as a cross reference in other system tables
RTR rtrConfigIfType	1.3.6.1.4.1.164.11.1.1.1.2	RtrIfConfigTYPE	read-create	This variable identifies the type of the specific entry in the rtrDynamicIfConfigTable. This field is writable only at creation time (i.e., when value of status is underCreation).
STR rtrConfigIfName	1.3.6.1.4.1.164.11.1.1.1.3	DisplayString	read-create	This variable provides a logical name to a specific entry in rtrConfigIfTable. It is also used in identifying the Driver interfaces.
ROW rtrConfigIfStatus	1.3.6.1.4.1.164.11.1.1.1.4	RowStatus	read-create	The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row is available for use by the managed device. createAndWait - A new instance of a conceptual row is desired, but not to have it available for use by the managed device. destroy - Delete all instances associated with an existing conceptual row.
rtrIfCfgTable	1.3.6.1.4.1.164.11.1.2		not-accessible	Router Interface Configuration Table.
rtrIfCfgEntry	1.3.6.1.4.1.164.11.1.2.1		not-accessible	An entry in the Router Interface Configuration Table.
I32 rtrIfCfgIndex	1.3.6.1.4.1.164.11.1.2.1.1	Integer32	read-create	This object indicates the Router Interface Index. (In some cases it will be equal to the Router Interface ifIndex).
IP rtrIfCfgIpAddress	1.3.6.1.4.1.164.11.1.2.1.2	IpAddress	read-create	IP Address of the Router Interface.
ROW rtrIfCfgRowStatus	1.3.6.1.4.1.164.11.1.2.1.3	RowStatus	read-create	This object enables the user to create/delete entries of this table.
IP rtrIfCfgIpMask	1.3.6.1.4.1.164.11.1.2.1.4	IpAddress	read-create	IP Mask Address Router Interface.
I32 rtrIfCfgIfIndex	1.3.6.1.4.1.164.11.1.2.1.5	Integer32	read-create	ifIndex of the device interface connected to this Router Interface.
INT rtrIfCfgType	1.3.6.1.4.1.164.11.1.2.1.6	INTEGER	read-create	The Router Interface Type. atm - ATM router interface lis - Logical IP Subnet router interface. ethernet - Ethernet router interface.
I32 rtrIfCfgVlanId	1.3.6.1.4.1.164.11.1.2.1.7	Integer32	read-create	The VLAN ID assigned to Tagged frames transmitted from this Router Interface. The value inserted should be a defined VLAN.
I32 rtrIfCfgMtu	1.3.6.1.4.1.164.11.1.2.1.8	Integer32	read-create	The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
ipSpec	1.3.6.1.4.1.164.11.2
rtrIpAddrTable	1.3.6.1.4.1.164.11.2.1		not-accessible	This table is parralel to MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.
rtrIpAddrEntry	1.3.6.1.4.1.164.11.2.1.1		not-accessible	The addressing information for one of this entity's IP addresses.
IP rtrIpAdEntAddr	1.3.6.1.4.1.164.11.2.1.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
I32 rtrIpAdEntIfIndex	1.3.6.1.4.1.164.11.2.1.1.2	Integer32	read-create	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP rtrIpAdEntNetMask	1.3.6.1.4.1.164.11.2.1.1.3	IpAddress	read-create	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
INT rtrIpAdEntForwardIpBroadcast	1.3.6.1.4.1.164.11.2.1.1.4	INTEGER	read-create	This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).
IP rtrIpAdEntBackupAddr	1.3.6.1.4.1.164.11.2.1.1.5	IpAddress	read-create
ROW rtrIpAdEntStatus	1.3.6.1.4.1.164.11.2.1.1.6	RowStatus	read-create	The Status variable is used to create and destroy a Ip Addresses.
icmpSpec	1.3.6.1.4.1.164.11.2.2
INT rtrIcmpGenErrMsgEnable	1.3.6.1.4.1.164.11.2.2.1	INTEGER	read-write	This variable controlls the ability to generate ICMP error messages
rtrIcmpRdTable	1.3.6.1.4.1.164.11.2.2.2		not-accessible	This table contains ICMP Router Discovery parameters configurated per IP interface.
rtrIcmpRdEntry	1.3.6.1.4.1.164.11.2.2.2.1		not-accessible	The ICMP parameters configurated for IP interface.
IP rtrIcmpRdIpAddr	1.3.6.1.4.1.164.11.2.2.2.1.1	IpAddress	read-only	The IP address to which this entry's information pertains.
IP rtrIcmpRdIpAdvertAddr	1.3.6.1.4.1.164.11.2.2.2.1.2	IpAddress	read-write	The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.255.255.
I32 rtrIcmpRdMaxAdvertInterval	1.3.6.1.4.1.164.11.2.2.2.1.3	Integer32	read-write	The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 1800 seconds.
I32 rtrIcmpRdMinAdvertInterval	1.3.6.1.4.1.164.11.2.2.2.1.4	Integer32	read-write	The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no greater than rtrIcmpRdMaxAdvertInterval. Default: 0.75 * rtrIcmpRdMaxAdvertInterval.
I32 rtrIcmpRdAdvertLifetime	1.3.6.1.4.1.164.11.2.2.2.1.5	Integer32	read-write	The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rtrIcmpRdMaxAdvertInterval and no greater than 9000 seconds. Default: 3 * rtrIcmpRdMaxAdvertInterval.
INT rtrIcmpRdAdvertise	1.3.6.1.4.1.164.11.2.2.2.1.6	INTEGER	read-write	A flag indicating whether or not the address is to be advertised.
I32 rtrIcmpRdPreferenceLevel	1.3.6.1.4.1.164.11.2.2.2.1.7	Integer32	read-write	The preferability of the address as a default router address, relative to other router addresses on the same subnet.
I32 rtrIcmpRdEntStatus	1.3.6.1.4.1.164.11.2.2.2.1.8	Integer32	read-write	Setting of any value to this object set values of all fields to the default values.
rip2Spec	1.3.6.1.4.1.164.11.2.3
rtrRip2IfConfTable	1.3.6.1.4.1.164.11.2.3.1		not-accessible	This table is an extension of rip2IfConfTable (RFC 1724 ,RIP 2). It means that every time somebody creates/destroys a row in the rip2IfConfTable, the same row should be automatically created/destroyed in this table.
rtrRip2IfConfEntry	1.3.6.1.4.1.164.11.2.3.1.1		not-accessible	An entry in table rtrRip2IfConfTable.
IP rtrRip2IfConfAddress	1.3.6.1.4.1.164.11.2.3.1.1.1	IpAddress	read-only	The IP Address of this system on the indicated subnet. For unnumbered interfaces, the value 0.0.0.N, where the least significant 24 bits (N) is the ifIndex for the IP Interface in network byte order
I32 rtrRip2IfConfVirtualDis	1.3.6.1.4.1.164.11.2.3.1.1.2	Integer32	read-write	This variable defines the virtual number of hops assigned to the interface specified by rtrIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.
INT rtrRip2IfConfAutoSend	1.3.6.1.4.1.164.11.2.3.1.1.3	INTEGER	read-write	When set to enable only the default route is sent through the interface. When set to disable, regular RIPs are sent.
INT rtrRip2IfConfRipEnable	1.3.6.1.4.1.164.11.2.3.1.1.4	INTEGER	read-write	This object shows whether RIP Protocol is enabled on the current interface.
arpSpec	1.3.6.1.4.1.164.11.2.4
I32 rtrArpDeleteTable	1.3.6.1.4.1.164.11.2.4.1	Integer32	read-write	Setting this object to any not-null value has the effect of deleting all entries of the ARP table.
I32 rtrArpInactiveTimeOut	1.3.6.1.4.1.164.11.2.4.2	Integer32	read-write	This variable defines the maximum time period (in second) that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
INT rtrArpProxy	1.3.6.1.4.1.164.11.2.4.3	INTEGER	read-write	When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on a different sub-net, provided they are it its network table. The router responds with its own MAC address. When ARP Proxy is disabled, the router responds only to ARP requests for its own IP addresses.
rtrNat	1.3.6.1.4.1.164.11.2.5
rtrNatIfConfTable	1.3.6.1.4.1.164.11.2.5.1		not-accessible	A list of interfaces which require separate NAT configuration.
rtrNatIfConfEntry	1.3.6.1.4.1.164.11.2.5.1.1		not-accessible	A single routing domain in a single subnet.
IP rtrNatIfVirtualAddress	1.3.6.1.4.1.164.11.2.5.1.1.1	IpAddress	read-only	The IP Address of the virtual subnet to be translated by the 'NAT box' attached to this interface.
IP rtrNatIfVirtualMask	1.3.6.1.4.1.164.11.2.5.1.1.2	IpAddress	read-only	The subnet Mask of the virtual subnet.
ROW rtrNatIfConfStatus	1.3.6.1.4.1.164.11.2.5.1.1.3	RowStatus	read-create	Writing 'destroy' has the effect of deleting this interface.
IP rtrNatIfRealAddress	1.3.6.1.4.1.164.11.2.5.1.1.4	IpAddress	read-create	The IP Address of the real subnet which is used by 'NAT box' for translation.
IP rtrNatIfRealMask	1.3.6.1.4.1.164.11.2.5.1.1.5	IpAddress	read-create	The subnet Mask of the real subnet.
INT rtrNatIfType	1.3.6.1.4.1.164.11.2.5.1.1.6	INTEGER	read-create	NAT type. static - Translate a specific virtual IP network to a specific real IP network. TCP, UDP and ICMP sessions originated both in real and virtual networks will be translated. dynamic - (Concurrent) Translate real IP network to larger or equal virtual IP network. TCP, UDP and ICMP sessions originated in virtual networks only can be translated and sessions originated in real networks will be rejected. A session that starts in the NAT system will be active until there will be no traffic for aging timeout period. pat - (Port Address Translation/ Single IP). Translate one real IP address to virtual IP network. TCP, UDP and ICMP sessions originated in virtual network only can be translated, sessions originated in real network will be rejected. A session that starts in the NAT system will be active until there will be no traffic for aging timeout period. transparent - In transparent mode all frames belonging to the defined IP network will be forwarded with no translation: virtual = real.
rtrPatTable	1.3.6.1.4.1.164.11.2.5.2		not-accessible	Port Address Translation (PAT - single IP NAT) configuration Table.
rtrPatEntry	1.3.6.1.4.1.164.11.2.5.2.1		not-accessible	Each entry describe unique mapping between real IP address, range of ports and protocol, to local (virtual) IP address. Ports are used in the TCP (rfc793) to name the ends of logical connections which carry long term conversations. For the purpose of providing services to unknown callers, a service contact port is defined.
I32 rtrPatIdx	1.3.6.1.4.1.164.11.2.5.2.1.1	Integer32	read-only	Running index for PAT table.
IP rtrPatRealAddress	1.3.6.1.4.1.164.11.2.5.2.1.2	IpAddress	read-create	The real IP Address used for translation
IP rtrPatVirtualAddress	1.3.6.1.4.1.164.11.2.5.2.1.3	IpAddress	read-create	The virtual IP Address used for translation
I32 rtrPatLowestPort	1.3.6.1.4.1.164.11.2.5.2.1.4	Integer32	read-create	Lowest Port number for this PAT entry
I32 rtrPatHighestPort	1.3.6.1.4.1.164.11.2.5.2.1.5	Integer32	read-create	Highest Port number for this PAT entry
INT rtrPatProtocol	1.3.6.1.4.1.164.11.2.5.2.1.6	INTEGER	read-create	Protocol selected. This Protocol and port range (lowest port - highest port) define the application (FTP, Telnet, SMTP etc.). Protocol enumaration numbers correspond to IP header 'protocol' field
ROW rtrPatStatus	1.3.6.1.4.1.164.11.2.5.2.1.7	RowStatus	read-create	This object enables creating and deleting entries of the table.
rtrFACS	1.3.6.1.4.1.164.11.5
INT rtrFACSDefaultAction	1.3.6.1.4.1.164.11.5.1	INTEGER	read-write	Used to define the default action for the device, when no FACS statements applicable to a given frame are defined.
rtrFACSActTable	1.3.6.1.4.1.164.11.5.2		not-accessible	The table of FACS action.
rtrFACSActEntry	1.3.6.1.4.1.164.11.5.2.1		not-accessible	Each rtrFACSActEntry consist of the following parameters
INT rtrFACSActType	1.3.6.1.4.1.164.11.5.2.1.1	INTEGER	read-only	This parameter indicates on which FACS Table the FACS action will preform.
I32 rtrFACSActIfIndex	1.3.6.1.4.1.164.11.5.2.1.2	Integer32	read-only	The interface to which this FACS entry is applicable.
INT rtrFACSAction	1.3.6.1.4.1.164.11.5.2.1.3	INTEGER	read-write	The management station that sends a SET request for one of these actions with indexes rtrFACSType and rtrFACSIfIndex defines the type and the interface Id for which all FACS statements are to be erased. If no interface or no type is specified, all FACS statements for a protocol are erased.
INT rtrFACSActiveDB	1.3.6.1.4.1.164.11.5.2.1.4	INTEGER	read-write	This parameter will point on which Facs DataBase the SNMP agent read. The Active dataBase is Read Only. The user may change FACS statements in the temporary DataBase and then write it to the Active DB.
rtrFACSTable	1.3.6.1.4.1.164.11.5.3		not-accessible	The table of FACS statment.
rtrFACSEntry	1.3.6.1.4.1.164.11.5.3.1		not-accessible	Each FACS statment consists of the following parameters
I32 rtrFACSIfIndex	1.3.6.1.4.1.164.11.5.3.1.1	Integer32	read-only	The interface to which this FACS entry is applicable. For applications this variables is always 0.
INT rtrFACSProtocolType	1.3.6.1.4.1.164.11.5.3.1.2	INTEGER	read-only	This parameter define the protocol the Security Access Control is applicable.
INT rtrFACSType	1.3.6.1.4.1.164.11.5.3.1.3	INTEGER	read-only	The Mode of in which this FACS statement operates. For applications this variable is always rx(2).
I32 rtrFACSIndex	1.3.6.1.4.1.164.11.5.3.1.4	Integer32	read-only	Index to the FACS Table.
OCT rtrFACSSrcAdd	1.3.6.1.4.1.164.11.5.3.1.5	OCTET STRING	read-write	The size of the octet string will be according to the protocol type defined in rtrFACSProtocolType.
OCT rtrFACSSrcAddMask	1.3.6.1.4.1.164.11.5.3.1.6	OCTET STRING	read-write	Source-address mask .
OCT rtrFACSDesAdd	1.3.6.1.4.1.164.11.5.3.1.7	OCTET STRING	read-write	Destination-address The size of the octet string will be according to the protocol type define in rtrFACSProtocolType .
OCT rtrFACSDesAddMask	1.3.6.1.4.1.164.11.5.3.1.8	OCTET STRING	read-write	Destination-address mask .
INT rtrFACSOperation	1.3.6.1.4.1.164.11.5.3.1.9	INTEGER	read-write	... .
INT rtrFACSNetFiltering	1.3.6.1.4.1.164.11.5.3.1.10	INTEGER	read-write	... .
I32 rtrFACSSocketNum	1.3.6.1.4.1.164.11.5.3.1.11	Integer32	read-write	Port/socket number for different applications 0 is default meaning not applicable. none(1), ftp(21), telnet(23), smtp(25), tftp(69), snmp(161), snmpTrap(162), rip(520), sapIPX(1106), ripIPX(1107)
I32 rtrFACSMask1Id	1.3.6.1.4.1.164.11.5.3.1.12	Integer32	read-write	Index into RND mask table FACS/COD Type) .
I32 rtrFACSMask2Id	1.3.6.1.4.1.164.11.5.3.1.13	Integer32	read-write	Index into RND mask table FACS/COD according to the value of rtrFACSType .
INT rtrFACSStatus	1.3.6.1.4.1.164.11.5.3.1.14	INTEGER	read-write	The status of a table entry.
OCT rtrFACSFrameData	1.3.6.1.4.1.164.11.5.4	OCTET STRING	read-only	Data from the frame that violated a FACS Filter.
rtrBridgePortConfigTable	1.3.6.1.4.1.164.11.7.1		not-accessible	Table of the bridge ports
rtrBridgePortConfigEntry	1.3.6.1.4.1.164.11.7.1.1		not-accessible	Each entry defines a bridge port
I32 rtrBridgePortCIndex	1.3.6.1.4.1.164.11.7.1.1.1	Integer32	read-only	This is the index of the bridge port. It is the same as 'dot1dBasePort' of the Bridge MIB.
I32 rtrBridgePortCIf	1.3.6.1.4.1.164.11.7.1.1.2	Integer32	read-create	The config ifIndex the bridge port is sitting on.
ROW rtrBridgePortCStatus	1.3.6.1.4.1.164.11.7.1.1.3	RowStatus	read-create	The status of the RtrBridgePortConfigEntry. Creating and destroying the bridge port is done by this variable.
radRouterConfig	1.3.6.1.4.1.164.11.9
rtrConfigTable	1.3.6.1.4.1.164.11.9.1		not-accessible	The Router's Configuration table.
rtrConfigEntry	1.3.6.1.4.1.164.11.9.1.1		not-accessible	An entry in the Router's Configuration table.
I32 rtrConfigIndex	1.3.6.1.4.1.164.11.9.1.1.1	Integer32	read-only	This object indicates the Router's Index.
IP rtrConfigDefaultGateway	1.3.6.1.4.1.164.11.9.1.1.2	IpAddress	read-write	Router Default Gateway.
I32 rtrConfigArpAgingTime	1.3.6.1.4.1.164.11.9.1.1.3	Integer32	read-write	ARP Aging Time.
I32 rtrConfigClassifierTosMask	1.3.6.1.4.1.164.11.9.1.1.5	Integer32	read-write	This object indicates the Classifier's TOS Mask, as follows: 0x1C for DTR -- rfc795 0x1E for Cisco 0xE0 for Precedence -- rfc795 0xFC for Diffserv Else for Manual .
INT rtrConfigRIPMode	1.3.6.1.4.1.164.11.9.1.1.6	INTEGER	read-write	This object determines the Router Information Protocol to measure the shortest path between 2 positions on the network.
rtrFwdTable	1.3.6.1.4.1.164.11.9.3		not-accessible	The Router's Forwarding Table.
rtrFwdEntry	1.3.6.1.4.1.164.11.9.3.1		not-accessible	An entry in the Router's Forwarding table.
I32 rtrFwdIdx	1.3.6.1.4.1.164.11.9.3.1.1	Integer32	read-only	This object indicates the Router Index.
IP rtrFwdIpAddress	1.3.6.1.4.1.164.11.9.3.1.2	IpAddress	read-only	This object indicates the Destination IP Address.
IP rtrFwdIpMask	1.3.6.1.4.1.164.11.9.3.1.3	IpAddress	read-only	This object indicates the Mask IP address.
I32 rtrFwdRuleIdx	1.3.6.1.4.1.164.11.9.3.1.4	Integer32	read-only	This object indicates the Rule's Number.
ROW rtrFwdRowStatus	1.3.6.1.4.1.164.11.9.3.1.5	RowStatus	read-create	This object enables the user to create/delete entries in this table. Entry of Type rtrFwdType = staticRouting(3) are created by the user. Only this type of entries can be deleted by the user. Entry of Type rtrFwdType = interface(2) are created/deleted automatically by the Agent when the user creates/deletes an interface of the Router.
IP rtrFwdNextHop	1.3.6.1.4.1.164.11.9.3.1.6	IpAddress	read-create	This object indicates the IP Address of the Next Hop.
I32 rtrFwdIfIndex	1.3.6.1.4.1.164.11.9.3.1.7	Integer32	read-only	This object indicates the Interface Index.
INT rtrFwdType	1.3.6.1.4.1.164.11.9.3.1.8	INTEGER	read-create	The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject (2) refers to a route which, if matched, discards the message as unreachable. This is used in some protocols as a means of correctly aggregating routes.
INT rtrFwdProto	1.3.6.1.4.1.164.11.9.3.1.9	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
I32 rtrFwdEthQueue	1.3.6.1.4.1.164.11.9.3.1.10	Integer32	read-create	This object indicates the ETH Queue number.
I32 rtrFwdMetric1	1.3.6.1.4.1.164.11.9.3.1.11	Integer32	read-create	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rtrFwdProto value. If this metric is not used, its value should be set to -1.
radAtmSignalingMonitor	1.3.6.1.4.1.164.12.6
INT smSVCOperState	1.3.6.1.4.1.164.12.6.1	INTEGER	read-only	The SVC monitoring operational state.
INT smSVCAdminStatus	1.3.6.1.4.1.164.12.6.2	INTEGER	read-write	The SVC monitoring status.
INT smILMIMode	1.3.6.1.4.1.164.12.6.3	INTEGER	read-write	The ILMI operational Mode.
INT smILMIStatus	1.3.6.1.4.1.164.12.6.4	INTEGER	read-only	ILMI protocol status (VCC 0,16).
INT smUNIVersion	1.3.6.1.4.1.164.12.6.5	INTEGER	read-write	The UNI version that is used by both sides.
INT smPolicing	1.3.6.1.4.1.164.12.6.6	INTEGER	read-write	The type of the police action performed on the cells transmitted from the user side to the network side.
INT smSAALStatus	1.3.6.1.4.1.164.12.6.7	INTEGER	read-only	Signaling data link (VCC 0,5) status.
G32 smOpenedSesssions	1.3.6.1.4.1.164.12.6.8	Gauge32	read-only	The number of SVC sessions currently opened.
G32 smUserRejectedSessions	1.3.6.1.4.1.164.12.6.9	Gauge32	read-only	The number of sessions that the user side rejected to open.
G32 smNetworkRejectedSessions	1.3.6.1.4.1.164.12.6.10	Gauge32	read-only	The number of sessions that the Network side rejected.
G32 smHostRejectedSessions	1.3.6.1.4.1.164.12.6.11	Gauge32	read-only	The number of sessions that the device rejected to open.
I32 smVclILMISessionVpi	1.3.6.1.4.1.164.12.6.12	Integer32	read-write	ILMI Keep alive session VPI channel. Default: 0. (VCI=16, fixed).

RFC description

RAD HDLC protocol configuration for V35, X21, and RS530 WAN interfaces.

Start monitoring RAD Data Communications HDLC WAN access equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAD-HDLC-MIB