SWITCH-RATELIMIT-MIB

All MIBs › SWITCH-RATELIMIT-MIB

Organization: Raisecom, Inc.

Last Updated: 2004-12-20

Description: SWITCH-RATELIMIT-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SWITCH-RATELIMIT-MIB?

SWITCH-RATELIMIT-MIB is a Raisecom module providing per-port ingress/egress traffic rate-limiting configuration and status, part of Raisecom's QoS/traffic-shaping management for its switch products. It exposes configured ingress and egress rate/burst limits per port, the operational (currently enforced) rate values, an enforcement rule selector, and an uplink-port designation. Its monitoring emphasis is software/QoS configuration and traffic-shaping status - comparing configured rate limits against the operationally applied values lets an operator catch policy drift or cases where the hardware failed to apply the intended rate limit. It ties into standard interface indexing conventions similar to IF-MIB's ifIndex for identifying ports. It is deployed on Raisecom carrier-access/aggregation switches that enforce per-port bandwidth limits on subscriber or uplink ports, and operators rely on this SWITCH-RATELIMIT-MIB monitor to catch policy drift before it affects traffic.

IPNetwork Monitor allows you to monitor SNMP objects defined in SWITCH-RATELIMIT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Raisecom carrier-access/aggregation switch

Monitoring Examples

rcRateLimitPortTable/rcRateLimitPortEntry (indexed by rcRateLimitPortIndex) holds configured rcRateLimitPortIngressRate/rcRateLimitPortIngressBurst and rcRateLimitPortEgressRate/rcRateLimitPortEgressBurst per port, along with rcRateLimitPortRule selecting the enforcement policy. An operator compares these configured values against rcRateLimitPortOperIngressRate/rcRateLimitPortOperEgressRate (the actually enforced rates) to confirm the switch is applying the intended limits, and checks rcUplinkPort to ensure rate limiting isn't inadvertently throttling the uplink. A mismatch between configured and operational rate values would indicate the rate-limit policy failed to apply or was overridden.

What Can Be Monitored

per-port ingress rate limit
per-port egress rate limit
ingress/egress burst size
operational (applied) rate values
uplink port designation

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From RAISECOM-BASE-MIB

iscomSwitch

OBJECT-IDENTITY

From RFC1155-SMI

Counter

From SNMPv2-SMI

Counter64

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

From SWITCH-TC

ClearVar
EnableVar

How to Use in IPNetwork Monitor

Example using rcRateLimitVlanCounterInprofilePkt64 OID:

Select a Raisecom carrier-access/aggregation switch (per-port ingress/egress rate-limit status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rcRateLimitVlanCounterInprofilePkt64 into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The pkt64 of the inprofile statistics. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
rcRateLimit	1.3.6.1.4.1.8886.6.1.2			description of rate limit manage object.
INT rcUplinkPort	1.3.6.1.4.1.8886.6.1.2.1	INTEGER	read-write	The uplink port based 1.
rcRateLimitPortTable	1.3.6.1.4.1.8886.6.1.2.2		not-accessible	A table of rate-limit for port and associated properties.
rcRateLimitPortEntry	1.3.6.1.4.1.8886.6.1.2.2.1		not-accessible	Table entry for rate-limit of port and status information.
INT rcRateLimitPortIndex	1.3.6.1.4.1.8886.6.1.2.2.1.1	INTEGER	read-only	The value of ifIndex that identifies the rate-limit of port which based 1.
INT rcRateLimitPortRule	1.3.6.1.4.1.8886.6.1.2.2.1.2	INTEGER	read-create	A rule of rate-limit for the port.
INT rcRateLimitPortIngressRate	1.3.6.1.4.1.8886.6.1.2.2.1.3	INTEGER	read-write	The value is the ingress rate( kbps) of the port.
INT rcRateLimitPortIngressBurst	1.3.6.1.4.1.8886.6.1.2.2.1.4	INTEGER	read-write	The value is the ingress burst( kB) of the port.
INT rcRateLimitPortEgressRate	1.3.6.1.4.1.8886.6.1.2.2.1.5	INTEGER	read-write	The value is the egress rate( kbps) of the port.
INT rcRateLimitPortEgressBurst	1.3.6.1.4.1.8886.6.1.2.2.1.6	INTEGER	read-write	The value is the egress burst( kB) of the port.
INT rcRateLimitPortOperIngressRate	1.3.6.1.4.1.8886.6.1.2.2.1.7	INTEGER	read-only	The value is the actual ingress rate( kbps) of the port.
INT rcRateLimitPortOperIngressBurst	1.3.6.1.4.1.8886.6.1.2.2.1.8	INTEGER	read-only	The value is the actual ingress burst( kB) of the port.
INT rcRateLimitPortOperEgressRate	1.3.6.1.4.1.8886.6.1.2.2.1.9	INTEGER	read-only	The value is the actual egress rate( kbps) of the port.
INT rcRateLimitPortOperEgressBurst	1.3.6.1.4.1.8886.6.1.2.2.1.10	INTEGER	read-only	The value is the actual egress burst( kB) of the port.
rcRateLimitVlanTable	1.3.6.1.4.1.8886.6.1.2.3		not-accessible	A table of rate-limit for vlan and associated properties.
rcRateLimitVlanEntry	1.3.6.1.4.1.8886.6.1.2.3.1		not-accessible	Table entry for rate-limit of vlan and status information.
INT rcRateLimitVlanType	1.3.6.1.4.1.8886.6.1.2.3.1.1	INTEGER	not-accessible	vlan type,single(1), double(2)?
INT rcRateLimitVlanCVlanID	1.3.6.1.4.1.8886.6.1.2.3.1.2	INTEGER	not-accessible	The vlan ID which identifies the customer vlan of rate limitation.
INT rcRateLimitVlanSPVlanID	1.3.6.1.4.1.8886.6.1.2.3.1.3	INTEGER	not-accessible	The vlan ID which identifies the service provider vlan of rate limitation.
INT rcRateLimitVlanRate	1.3.6.1.4.1.8886.6.1.2.3.1.4	INTEGER	read-create	The value is the input rate( kbps) of the vlan.
INT rcRateLimitVlanBurst	1.3.6.1.4.1.8886.6.1.2.3.1.5	INTEGER	read-create	The value is the input burst( kB) of the vlan.
ROW rcRateLimitVlanRowStatus	1.3.6.1.4.1.8886.6.1.2.3.1.6	RowStatus	read-create	The status of this entry.
ENA rcRateLimitVlanStatsEnable	1.3.6.1.4.1.8886.6.1.2.3.1.7	EnableVar	read-create	enable statistics or not.
ENA rcRateLimitVlanStatHwStatus	1.3.6.1.4.1.8886.6.1.2.3.1.8	EnableVar	read-create	in hardware or not.
rcRateLimitVlanStatisticsTable	1.3.6.1.4.1.8886.6.1.2.4		not-accessible	A table of vlan rate limit statistics.
rcRateLimitVlanStatisticsEntry	1.3.6.1.4.1.8886.6.1.2.4.1		not-accessible	Table entry for vlan rate limit statistics .
ENA rcRateLimitVlanCounterReset	1.3.6.1.4.1.8886.6.1.2.4.1.1	EnableVar	read-write	clear the statistics.
C64 rcRateLimitVlanCounterInprofilePkt64Ex	1.3.6.1.4.1.8886.6.1.2.4.1.2	Counter64	read-only	The pkt64 of the inprofile statistics.
C64 rcRateLimitVlanCounterInprofileByte64	1.3.6.1.4.1.8886.6.1.2.4.1.3	Counter64	read-only	The Byte64 of the inprofile statistics.
C64 rcRateLimitVlanCounterOutprofilePkt64	1.3.6.1.4.1.8886.6.1.2.4.1.4	Counter64	read-only	The pkt64 of the outprofile statistics.
C64 rcRateLimitVlanCounterOutprofileByte64	1.3.6.1.4.1.8886.6.1.2.4.1.5	Counter64	read-only	The Byte64 of the outprofile statistics.
INT rcRateLimitVlanCounterStatisticUnit	1.3.6.1.4.1.8886.6.1.2.4.1.6	INTEGER	read-only	Vlan rate-limit statistics unit.
rcRateLimitVlanPortTable	1.3.6.1.4.1.8886.6.1.2.5		not-accessible	A table of rate-limit based on vlan-port.
rcRateLimitVlanPortEntry	1.3.6.1.4.1.8886.6.1.2.5.1		not-accessible	Table entry of rate-limit based on vlan-port.
INT rcRateLimitVlanPortDirection	1.3.6.1.4.1.8886.6.1.2.5.1.1	INTEGER	read-create	This object specifies the type of port direction.
INT rcRateLimitVlanPortVlanID	1.3.6.1.4.1.8886.6.1.2.5.1.2	INTEGER	read-create	This object specifies the vlan ID which identifies the outer vlan.
INT rcRateLimitVlanPortCir	1.3.6.1.4.1.8886.6.1.2.5.1.3	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitVlanPortCbs	1.3.6.1.4.1.8886.6.1.2.5.1.4	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
INT rcRateLimitVlanPortEir	1.3.6.1.4.1.8886.6.1.2.5.1.5	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitVlanPortEbs	1.3.6.1.4.1.8886.6.1.2.5.1.6	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
ENA rcRateLimitVlanPortStatsEnable	1.3.6.1.4.1.8886.6.1.2.5.1.7	EnableVar	read-write	Enable statistics or not.
ROW rcRateLimitVlanPortRowStatus	1.3.6.1.4.1.8886.6.1.2.5.1.8	RowStatus	read-write	The status of this entry.
rcRateLimitVlanPortStatisticsTable	1.3.6.1.4.1.8886.6.1.2.6		not-accessible	The statistic table of rate-limit based on vlan-port.
rcRateLimitVlanPortStatisticsEntry	1.3.6.1.4.1.8886.6.1.2.6.1		not-accessible	The statistic table entry of rate-limit based on vlan-port.
CLE rcRateLimitVlanPortCounterReset	1.3.6.1.4.1.8886.6.1.2.6.1.1	ClearVar	read-write	Clear the statistics.
C64 rcRateLimitVlanPortCounterInprofilePkt64	1.3.6.1.4.1.8886.6.1.2.6.1.2	Counter64	read-only	The pkt64 of the inprofile statistics.
C64 rcRateLimitVlanPortCounterInprofileByte64	1.3.6.1.4.1.8886.6.1.2.6.1.3	Counter64	read-only	The Byte64 of the inprofile statistics.
C64 rcRateLimitVlanPortCounterOutprofilePkt64	1.3.6.1.4.1.8886.6.1.2.6.1.4	Counter64	read-only	The pkt64 of the outprofile statistics.
C64 rcRateLimitVlanPortCounterOutprofileByte64	1.3.6.1.4.1.8886.6.1.2.6.1.5	Counter64	read-only	The Byte64 of the outprofile statistics.
rcRateLimitVlanPortHistoryControlTable	1.3.6.1.4.1.8886.6.1.2.7		not-accessible	A table of vlan Port History Control.
rcRateLimitVlanPortHistoryControlEntry	1.3.6.1.4.1.8886.6.1.2.7.1		not-accessible	Table entry for vlan Port History Control.
CTR rcRateLimitVlanPortHistoryControlVlanIndex	1.3.6.1.4.1.8886.6.1.2.7.1.1	Counter	read-create	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
CTR rcRateLimitVlanPortHistoryControlPortIndex	1.3.6.1.4.1.8886.6.1.2.7.1.2	Counter	read-create	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
INT rcRateLimitVlanPortHistoryControlSVlan	1.3.6.1.4.1.8886.6.1.2.7.1.3	INTEGER	read-only	SVlan ID.
INT rcRateLimitVlanPortHistoryControlCVlan	1.3.6.1.4.1.8886.6.1.2.7.1.4	INTEGER	read-only	CVlan ID.
INT rcRateLimitVlanPortHistoryControlSCoS	1.3.6.1.4.1.8886.6.1.2.7.1.5	INTEGER	read-only	SCoS value.
INT rcRateLimitVlanPortHistoryControlCCoS	1.3.6.1.4.1.8886.6.1.2.7.1.6	INTEGER	read-only	CCoS value.
INT rcRateLimitVlanPortHistoryControlPort	1.3.6.1.4.1.8886.6.1.2.7.1.7	INTEGER	read-write	This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573 [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
ENT rcRateLimitVlanPortHistoryControlStatus	1.3.6.1.4.1.8886.6.1.2.7.1.8	EntryStatus	read-write	The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).
rcRateLimitVlanPortHistoryTable	1.3.6.1.4.1.8886.6.1.2.8		not-accessible	A table of vlan Port History statics.
rcRateLimitVlanPortHistoryEntry	1.3.6.1.4.1.8886.6.1.2.8.1		not-accessible	Table entry for vlan Port History Control.
CTR rcRateLimitVlanPortHistoryVlanIndex	1.3.6.1.4.1.8886.6.1.2.8.1.1	Counter	read-only	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
CTR rcRateLimitVlanPortHistoryPortIndex	1.3.6.1.4.1.8886.6.1.2.8.1.2	Counter	read-only	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
INT rcRateLimitVlanPortHistorySampleIndex	1.3.6.1.4.1.8886.6.1.2.8.1.3	INTEGER	read-only	An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
TIK rcRateLimitVlanPortHistoryHistoryIntervalStart	1.3.6.1.4.1.8886.6.1.2.8.1.4	TimeTicks	read-only	The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of the time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collecting the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
C64 rcRateLimitVlanPortHistoryIngressInPkt	1.3.6.1.4.1.8886.6.1.2.8.1.5	Counter64	read-only	The total number of IngressInPkt.
C64 rcRateLimitVlanPortHistoryIngressOutPkt	1.3.6.1.4.1.8886.6.1.2.8.1.6	Counter64	read-only	The total number of IngressOutPkt.
C64 rcRateLimitVlanPortHistoryIngressInByte	1.3.6.1.4.1.8886.6.1.2.8.1.7	Counter64	read-only	The total number of IngressInByte.
C64 rcRateLimitVlanPortHistoryIngressOutBytes	1.3.6.1.4.1.8886.6.1.2.8.1.8	Counter64	read-only	The total number of IngressOutBytes.
C64 rcRateLimitVlanPortHistoryEgressInPkt	1.3.6.1.4.1.8886.6.1.2.8.1.9	Counter64	read-only	The total number of EgressInPkt.
C64 rcRateLimitVlanPortHistoryEgressOutPkt	1.3.6.1.4.1.8886.6.1.2.8.1.10	Counter64	read-only	The total number of EgressOutPkt.
C64 rcRateLimitVlanPortHistoryEgressInByte	1.3.6.1.4.1.8886.6.1.2.8.1.11	Counter64	read-only	The total number of EgressInByte.
C64 rcRateLimitVlanPortHistoryEgressOutBytes	1.3.6.1.4.1.8886.6.1.2.8.1.12	Counter64	read-only	The total number of EgressOutBytes.
rcRateLimitCosVlanPortTable	1.3.6.1.4.1.8886.6.1.2.9		not-accessible	A table of rate-limit based on vlan-port-cos.
rcRateLimitCosVlanPortEntry	1.3.6.1.4.1.8886.6.1.2.9.1		not-accessible	Table entry of rate-limit based on vlan-port-cos.
INT rcRateLimitCosVlanPortDirection	1.3.6.1.4.1.8886.6.1.2.9.1.1	INTEGER	read-create	This object specifies the type of port direction.
INT rcRateLimitCosVlanPortVlanID	1.3.6.1.4.1.8886.6.1.2.9.1.2	INTEGER	read-create	This object specifies the vlan ID which identifies the outer vlan.
INT rcRateLimitCosVlanPortCos	1.3.6.1.4.1.8886.6.1.2.9.1.3	INTEGER	read-write	The port's priority.
INT rcRateLimitCosVlanPortCir	1.3.6.1.4.1.8886.6.1.2.9.1.4	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitCosVlanPortCbs	1.3.6.1.4.1.8886.6.1.2.9.1.5	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
INT rcRateLimitCosVlanPortEir	1.3.6.1.4.1.8886.6.1.2.9.1.6	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitCosVlanPortEbs	1.3.6.1.4.1.8886.6.1.2.9.1.7	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
ENA rcRateLimitCosVlanPortStatsEnable	1.3.6.1.4.1.8886.6.1.2.9.1.8	EnableVar	read-write	Enable statistics or not.
ROW rcRateLimitCosVlanPortRowStatus	1.3.6.1.4.1.8886.6.1.2.9.1.9	RowStatus	read-write	The status of this entry.
rcRateLimitCosVlanPortStatisticsTable	1.3.6.1.4.1.8886.6.1.2.10		not-accessible	The statistic table of rate-limit based on vlan-port-cos.
rcRateLimitCosVlanPortStatisticsEntry	1.3.6.1.4.1.8886.6.1.2.10.1		not-accessible	The statistic table entry of rate-limit based on vlan-port-cos.
CLE rcRateLimitCosVlanPortCounterReset	1.3.6.1.4.1.8886.6.1.2.10.1.1	ClearVar	read-write	Clear the statistics.
C64 rcRateLimitCosVlanPortCounterInprofilePkt64	1.3.6.1.4.1.8886.6.1.2.10.1.2	Counter64	read-only	The pkt64 of the inprofile statistics.
C64 rcRateLimitCosVlanPortCounterInprofileByte64	1.3.6.1.4.1.8886.6.1.2.10.1.3	Counter64	read-only	The Byte64 of the inprofile statistics.
C64 rcRateLimitCosVlanPortCounterOutprofilePkt64	1.3.6.1.4.1.8886.6.1.2.10.1.4	Counter64	read-only	The pkt64 of the outprofile statistics.
C64 rcRateLimitCosVlanPortCounterOutprofileByte64	1.3.6.1.4.1.8886.6.1.2.10.1.5	Counter64	read-only	The Byte64 of the outprofile statistics.
rcRateLimitDscpVlanPortTable	1.3.6.1.4.1.8886.6.1.2.11		not-accessible	A table of rate-limit based on port+vlan+dscp.
rcRateLimitDscpVlanPortEntry	1.3.6.1.4.1.8886.6.1.2.11.1		not-accessible	Table entry of rate-limit based on port+vlan+dscp.
INT rcRateLimitDscpVlanPortDirection	1.3.6.1.4.1.8886.6.1.2.11.1.1	INTEGER	read-create	This object specifies the type of port direction.
INT rcRateLimitDscpVlanPortVlanID	1.3.6.1.4.1.8886.6.1.2.11.1.2	INTEGER	read-create	This object specifies the vlan ID which identifies the outer vlan.
INT rcRateLimitDscpVlanPortDscp	1.3.6.1.4.1.8886.6.1.2.11.1.3	INTEGER	read-create	The port's dscp value.
INT rcRateLimitDscpVlanPortCir	1.3.6.1.4.1.8886.6.1.2.11.1.4	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitDscpVlanPortCbs	1.3.6.1.4.1.8886.6.1.2.11.1.5	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
INT rcRateLimitDscpVlanPortEir	1.3.6.1.4.1.8886.6.1.2.11.1.6	INTEGER	read-write	The value is the input rate(kbps) of the vlan on each port.
INT rcRateLimitDscpVlanPortEbs	1.3.6.1.4.1.8886.6.1.2.11.1.7	INTEGER	read-write	The value is the input burst(kB) of the vlan on each port.
ENA rcRateLimitDscpVlanPortStatsEnable	1.3.6.1.4.1.8886.6.1.2.11.1.8	EnableVar	read-write	Enable statistics or not.
ROW rcRateLimitDscpVlanPortRowStatus	1.3.6.1.4.1.8886.6.1.2.11.1.9	RowStatus	read-write	The status of this entry.
rcRateLimitDscpVlanPortStatisticsTable	1.3.6.1.4.1.8886.6.1.2.12		not-accessible	The statistic table of rate-limit based on port+vlan+dscp.
rcRateLimitDscpVlanPortStatisticsEntry	1.3.6.1.4.1.8886.6.1.2.12.1		not-accessible	The statistic table entry of rate-limit based on port+vlan+dscp.
CLE rcRateLimitDscpVlanPortCounterReset	1.3.6.1.4.1.8886.6.1.2.12.1.1	ClearVar	read-write	Clear the statistics.
C64 rcRateLimitDscpVlanPortCounterInprofilePkt64	1.3.6.1.4.1.8886.6.1.2.12.1.2	Counter64	read-only	The pkt64 of the inprofile statistics.
C64 rcRateLimitDscpVlanPortCounterInprofileByte64	1.3.6.1.4.1.8886.6.1.2.12.1.3	Counter64	read-only	The Byte64 of the inprofile statistics.
C64 rcRateLimitDscpVlanPortCounterOutprofilePkt64	1.3.6.1.4.1.8886.6.1.2.12.1.4	Counter64	read-only	The pkt64 of the outprofile statistics.
C64 rcRateLimitDscpVlanPortCounterOutprofileByte64	1.3.6.1.4.1.8886.6.1.2.12.1.5	Counter64	read-only	The Byte64 of the outprofile statistics.
INT rcRatelimitMode	1.3.6.1.4.1.8886.6.1.2.13	INTEGER	read-write	The rate-limit mode, l1(1),l2(2).
rcRateLimitDscpVlanPortHistoryControlTable	1.3.6.1.4.1.8886.6.1.2.14		not-accessible	A table of vlan Port Dscp History Control.
rcRateLimitDscpVlanPortHistoryControlEntry	1.3.6.1.4.1.8886.6.1.2.14.1		not-accessible	Table entry for vlan Port Dscp History Control.
CTR rcRateLimitDscpVlanPortHistoryControlVlanIndex	1.3.6.1.4.1.8886.6.1.2.14.1.1	Counter	read-create	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
CTR rcRateLimitDscpVlanPortHistoryControlPortIndex	1.3.6.1.4.1.8886.6.1.2.14.1.2	Counter	read-create	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
INT rcRateLimitDscpVlanPortHistoryControlSVlan	1.3.6.1.4.1.8886.6.1.2.14.1.3	INTEGER	read-only	SVlan ID.
INT rcRateLimitDscpVlanPortHistoryControlDscp	1.3.6.1.4.1.8886.6.1.2.14.1.4	INTEGER	read-only	Dscp ID.
INT rcRateLimitDscpVlanPortHistoryControlPort	1.3.6.1.4.1.8886.6.1.2.14.1.5	INTEGER	read-write	This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573 [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
ENT rcRateLimitDscpVlanPortHistoryControlStatus	1.3.6.1.4.1.8886.6.1.2.14.1.6	EntryStatus	read-write	The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).
rcRateLimitDscpVlanPortHistoryTable	1.3.6.1.4.1.8886.6.1.2.15		not-accessible	A table of vlan Port Dscp History statics.
rcRateLimitDscpVlanPortHistoryEntry	1.3.6.1.4.1.8886.6.1.2.15.1		not-accessible	Table entry for vlan Port Dscp History Control.
CTR rcRateLimitDscpVlanPortHistoryVlanIndex	1.3.6.1.4.1.8886.6.1.2.15.1.1	Counter	read-only	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
CTR rcRateLimitDscpVlanPortHistoryPortIndex	1.3.6.1.4.1.8886.6.1.2.15.1.2	Counter	read-only	An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
INT rcRateLimitDscpVlanPortHistorySampleIndex	1.3.6.1.4.1.8886.6.1.2.15.1.3	INTEGER	read-only	An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
TIK rcRateLimitDscpVlanPortHistoryHistoryIntervalStat	1.3.6.1.4.1.8886.6.1.2.15.1.4	TimeTicks	read-only	The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of the time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collecting the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
C64 rcRateLimitDscpVlanPortHistoryIngressInPkt	1.3.6.1.4.1.8886.6.1.2.15.1.5	Counter64	read-only	The total number of IngressInPkt.
C64 rcRateLimitDscpVlanPortHistoryIngressOutPkt	1.3.6.1.4.1.8886.6.1.2.15.1.6	Counter64	read-only	The total number of IngressOutPkt.
C64 rcRateLimitDscpVlanPortHistoryIngressInByte	1.3.6.1.4.1.8886.6.1.2.15.1.7	Counter64	read-only	The total number of IngressInByte.
C64 rcRateLimitDscpVlanPortHistoryIngressOutByte	1.3.6.1.4.1.8886.6.1.2.15.1.8	Counter64	read-only	The total number of IngressOutBytes.
C64 rcRateLimitDscpVlanPortHistoryEgressInPkt	1.3.6.1.4.1.8886.6.1.2.15.1.9	Counter64	read-only	The total number of EgressInPkt.
C64 rcRateLimitDscpVlanPortHistoryEgressOutPkt	1.3.6.1.4.1.8886.6.1.2.15.1.10	Counter64	read-only	The total number of EgressOutPkt.
C64 rcRateLimitDscpVlanPortHistoryEgressInByte	1.3.6.1.4.1.8886.6.1.2.15.1.11	Counter64	read-only	The total number of EgressInByte.
C64 rcRateLimitDscpVlanPortHistoryEgressOutByte	1.3.6.1.4.1.8886.6.1.2.15.1.12	Counter64	read-only	The total number of EgressOutBytes.

RFC description

Configures and monitors rate-limiting functionality for bandwidth management on switch ports.

Start monitoring Raisecom carrier-access/aggregation switch (per-port ingress/egress rate-limit status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SWITCH-RATELIMIT-MIB