All MIBs › SWITCH-RATELIMIT-MIB › rcRateLimitVlanPortHistoryControlPort
rcRateLimitVlanPortHistoryControlPort
Module: SWITCH-RATELIMIT-MIB
OID (symbolic): SWITCH-RATELIMIT-MIB::rcRateLimitVlanPortHistoryControlPort
OID (numeric): 1.3.6.1.4.1.8886.6.1.2.7.1.7
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573 [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1.
The statistics in this group reflect all packets on the local network segment attached to the identified interface.
An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry.
This object may not be modified if the associated historyControlStatus object is equal to valid(1).
What is rcRateLimitVlanPortHistoryControlPort?
Read-write integer identifying the ifIndex of the interface this history-control entry collects samples from, per the RFC 1213/1573 historyControl model this MIB borrows from RMON. Set this to the port you want historical rate-limit statistics gathered for; it can't be changed once rcRateLimitVlanPortHistoryControlStatus is 'valid'.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.8886.6.1.2.7.1.7 snmpwalk -v2c -c public <target> SWITCH-RATELIMIT-MIB::rcRateLimitVlanPortHistoryControlPort
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.8886.6.1.2.7.1.7.1 snmpget -v2c -c public <target> SWITCH-RATELIMIT-MIB::rcRateLimitVlanPortHistoryControlPort.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.8886.6.1.2.7.1.7.1 i <value>
Start monitoring Raisecom carrier-access/aggregation switch (per-port ingress/egress rate-limit status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the SWITCH-RATELIMIT-MIB::rcRateLimitVlanPortHistoryControlPort OID value, configure state conditions and alerts, and monitor any Raisecom carrier-access/aggregation switch (per-port ingress/egress rate-limit status) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.8886 | raisecom | RAISECOM-BASE-MIB |
| 1.3.6.1.4.1.8886.6 | iscomSeries | RAISECOM-BASE-MIB |
| 1.3.6.1.4.1.8886.6.1 | iscomSwitch | RAISECOM-BASE-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.8886.6.1.2 | rcRateLimit | SWITCH-RATELIMIT-MIB |
| 1.3.6.1.4.1.8886.6.1.2.7 | rcRateLimitVlanPortHistoryControlTable | SWITCH-RATELIMIT-MIB |
| 1.3.6.1.4.1.8886.6.1.2.7.1 | rcRateLimitVlanPortHistoryControlEntry | SWITCH-RATELIMIT-MIB |
| 1.3.6.1.4.1.8886.6.1.2.7.1.7 | rcRateLimitVlanPortHistoryControlPort | SWITCH-RATELIMIT-MIB |