STN-ATM-MIB

All MIBs › STN-ATM-MIB

Organization: Spring Tide Networks, Inc.

Last Updated: 2000-02-16

Category: ATM, Spring Tide Networks

Description: Manages Spring Tide Networks ATM interface configuration, virtual circuit parameters, and traffic statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is STN-ATM-MIB?

STN-ATM-MIB is a vendor MIB from Spring Tide Networks for configuring and monitoring ATM (Asynchronous Transfer Mode) interfaces on their broadband aggregation platforms, covering virtual circuit (VC) parameters and interface-level ATM traffic statistics. It exposes ATM interface configuration and virtual circuit setup along with traffic counters (cell/packet counts, errors) used to gauge the health and utilization of ATM trunks. This MIB supports monitoring of both configuration/software status (VC provisioning correctness) and performance/hardware-adjacent status (traffic and error counters on the physical ATM interface), helping operators detect misconfigured circuits or degraded ATM links. It depends on the SPRING-TIDE-NETWORKS-SMI for its enterprise OID root and is designed to complement STN-IF-MIB, which provides the generic interface-level status for the same physical ports. Typical deployment context is legacy carrier/broadband aggregation networks where Spring Tide equipment aggregated DSL or other access traffic over ATM backhaul links. Engineers can download the STN-ATM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in STN-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Spring Tide Networks broadband aggregation equipment with ATM interfaces

Monitoring Examples

No object names were captured for this MIB, but a realistic scenario would involve polling an ATM VC table (following the vendor's typical *Table/*Entry convention, e.g., stnAtmVcTable/stnAtmVcEntry) to confirm configured VPI/VCI values and traffic class match provisioning records. An admin would monitor ATM interface cell error and cell-discard counters to detect a degrading trunk before it causes subscriber service issues. A VC showing zero traffic where volume is expected would indicate a provisioning or upstream connectivity fault.

What Can Be Monitored

ATM virtual circuit configuration (VPI/VCI)
ATM interface cell/traffic counters
ATM cell error/discard counts
VC provisioning status

Imported Objects

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TruthValue

From SPRING-TIDE-NETWORKS-SMI

stnNotification	OBJECT-IDENTITY
stnSystems	OBJECT-IDENTITY

From SPRING-TIDE-NETWORKS-TC

NSAPAddress

From STN-ROUTER-MIB

stnRouterIndex

OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using stnAtmPortTrafTxCells OID:

Select a Spring Tide Networks broadband aggregation device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type stnAtmPortTrafTxCells into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of ATM cells transmitted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
stnAtm	1.3.6.1.4.1.3551.2.6			Initial version of this MIB module.
stnAtmObjects	1.3.6.1.4.1.3551.2.6.1
stnAtmLinks	1.3.6.1.4.1.3551.2.6.1.1
stnVcLinks	1.3.6.1.4.1.3551.2.6.1.1.1
stnVcLinkTable	1.3.6.1.4.1.3551.2.6.1.1.1.1		not-accessible	A list of VC Link entries.
stnVcLinkEntry	1.3.6.1.4.1.3551.2.6.1.1.1.1.1		not-accessible	Entry contains information about a particular VC link.
NUM stnVcLinkIfIndex	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
I32 stnVcLinkVpi	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.2	Integer32	read-only	The VPI value of the VPL. Note that the VPI=0 is not used for a VPL not associated with a VCL. The maximum VPI value cannot exceed the value allowable by the atmInterfaceMaxVpiBits.
I32 stnVcLinkVci	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.3	Integer32	read-only	The VCI value of the VCL. The maximum VCI value cannot exceed the value allowable by the atmInterfaceMaxVciBits.
I32 stnVcLinkRcvTrafDescr	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.4	Integer32	read-only	Receive traffic descriptor identifier for this VPL.
I32 stnVcLinkXmtTrafDescr	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.5	Integer32	read-only	Transmit traffic descriptor identifier for this VPL.
I32 stnVcLinkAalObjectsValid	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.6	Integer32	read-only	Indicates whether the following AAL objects are valid (whether the local VCL end-point is also the VCC end-point). Transmit traffic descriptor identifier for this VPL.
INT stnVcLinkAalType	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.7	INTEGER	read-only	An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL type includes AAL1, AAL3/4, and AAL5. The other(4) may be used as a user-defined AAL type. The unknown type indicates that the AAL type cannot be determined.
I32 stnVcLinkAal5XmtSDUSize	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.8	Integer32	read-only	An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDUsize in octets that is supported on the transmit direction of this VCC.
I32 stnVcLinkAal5RcvSDUSize	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.9	Integer32	read-only	An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the receive direction of this VCC.
I32 stnVcLinkAal5EncapsType	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.10	Integer32	read-only	An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.
INT stnVcLinkCastType	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.11	INTEGER	read-only	The type of topology of a connection (point- to-point, point-to-multipoint). In the case of point-to-multipoint, the orientation of this VPL in the connection. On a host, p2mpRoot indicates that the host is the root of the p2mp connection, p2mpLeaf indicates that the host is a leaf of the p2mp connection. On a switch, p2mpRoot indicates that cells received by the switching fabric from the interface are from the root of the p2mp connection, p2mpLeaf indicates that cells transmitted to the interface from the switching fabric are to the leaf of the p2mp connection.
INT stnVcLinkConnKind	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.12	INTEGER	read-only	The use of call control. An spvcInitiator is always cross-connected to an svcOutgoing, and an spvcTarget is always cross-connected to an svcIncoming.
T/F stnVcLinkAccEnabled	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.13	TruthValue	read-only	ATM accounting is enabled for this VC Link.
T/F stnVcLinkOAMMgmtEnabled	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.14	TruthValue	read-only	OAM management is enabled.
I32 stnVcLinkOAMXmtFrequency	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.15	Integer32	read-only	Number of seconds between transmitting OAM loopback cells.
I32 stnVcLinkOAMRetryUpCount	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.16	Integer32	read-only	Number of consecutive end-to-end F5 OAM loopback cell responses that must be received in order to change a PVC state to up. Does not apply to SVCs.
I32 stnVcLinkOAMRetryDownCount	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.17	Integer32	read-only	Number of consecutive end-to-end F5 OAM loopback cell responses that are not received in order to change a PVC state to down or tear down an SVC.
I32 stnVcLinkOAMRetryFrequency	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.18	Integer32	read-only	The frequency (in seconds) that end-to-end F5 loopback cells should be transmitted when a change in UP/DOWN state is being verified. For example, if a PVC is up and a loopback cell response is not received after the frequency (in seconds, then loopback cells are sent at the retry-frequency to verify whether or not the PVC is down.
I32 stnVcLinkPppId	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.19	Integer32	read-only	PPP ID
VCL stnVcLinkOperStatus	1.3.6.1.4.1.3551.2.6.1.1.1.1.1.20	VcLinkOperStatus	read-only	Operational status of the VC Link.
stnAtmCrossConns	1.3.6.1.4.1.3551.2.6.1.2
stnVcCrossConns	1.3.6.1.4.1.3551.2.6.1.2.1
stnVcCrossConnTable	1.3.6.1.4.1.3551.2.6.1.2.1.1		not-accessible	A list of VC cross connection entries.
stnVcCrossConnEntry	1.3.6.1.4.1.3551.2.6.1.2.1.1.1		not-accessible	Entry contains information about a particular VC cross connection.
NUM stnVcCrossConnLowIfIndex	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.1	InterfaceIndex	read-only	The value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex.
I32 stnVcCrossConnLowVpi	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.2	Integer32	read-only	The value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at the low ATM interface port.
I32 stnVcCrossConnLowVci	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.3	Integer32	read-only	The value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value cannot exceed the number supported by the atmInterfaceMaxVciBits at the low ATM interface port.
NUM stnVcCrossConnHighIfIndex	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.4	InterfaceIndex	read-only	The value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex.
I32 stnVcCrossConnHighVpi	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.5	Integer32	read-only	The value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at the low ATM interface port.
I32 stnVcCrossConnHighVci	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.6	Integer32	read-only	The value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value cannot exceed the number supported by the atmInterfaceMaxVciBits at the low ATM interface port.
T/F stnVcCrossConnLowAutoAssign	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.7	TruthValue	read-only	Controls low vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF.
T/F stnVcCrossConnHighAutoAssign	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.8	TruthValue	read-only	Controls high vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF.
VCC stnVcCrossConnOperStatus	1.3.6.1.4.1.3551.2.6.1.2.1.1.1.9	VcCrossConnOperStatus	read-only	Operational status of the VC cross connection.
stnVpCrossConns	1.3.6.1.4.1.3551.2.6.1.2.2
stnAtmTrafficDescrs	1.3.6.1.4.1.3551.2.6.1.3
stnTrafficDescrTable	1.3.6.1.4.1.3551.2.6.1.3.1		not-accessible	A list of ATM traffic descriptor entries.
stnTrafficDescrEntry	1.3.6.1.4.1.3551.2.6.1.3.1.1		not-accessible	Entry contains information about a particular ATM traffic descriptor.
I32 stnTrafDescrIndex	1.3.6.1.4.1.3551.2.6.1.3.1.1.1	Integer32	read-only	The value of this object identifies the row in the stnTrafficDescrTable.
OCT stnTrafDescrName	1.3.6.1.4.1.3551.2.6.1.3.1.1.2	OCTET STRING	read-only	Text name assigned to this traffic descriptor.
INT stnTrafDescrType	1.3.6.1.4.1.3551.2.6.1.3.1.1.3	INTEGER	read-only	The value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmTrafDescrParam1, atmTrafDescrParam2, atmTrafDescrParam3, atmTrafDescrParam4, atmTrafDescrParam5 Type values are as follows: no-td no-clp-no-scr clp-no-ag-no-scr clp-agging-no-scr no-clp-scr clp-no-tag-scr clp-tagging-scr clp-no-tag-mcr clp-trans-no-scr clp-trans-scr no-clp-tag-no-scr
I32 stnTrafDescrParam1	1.3.6.1.4.1.3551.2.6.1.3.1.1.4	Integer32	read-only	The first parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.
I32 stnTrafDescrParam2	1.3.6.1.4.1.3551.2.6.1.3.1.1.5	Integer32	read-only	The second parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.
I32 stnTrafDescrParam3	1.3.6.1.4.1.3551.2.6.1.3.1.1.6	Integer32	read-only	The third parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.
I32 stnTrafDescrParam4	1.3.6.1.4.1.3551.2.6.1.3.1.1.7	Integer32	read-only	The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.
I32 stnTrafDescrParam5	1.3.6.1.4.1.3551.2.6.1.3.1.1.8	Integer32	read-only	The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.
INT stnTrafDescrQosClass	1.3.6.1.4.1.3551.2.6.1.3.1.1.9	INTEGER	read-only	The value of this object identifies the QoS Class. Four Service classes have been specified in the ATM Forum UNI Specification: Service Class A: Constant bit rate video and Circuit emulation. Service Class B: Variable bit rate video/audio. Service Class C: Connection-oriented data. Service Class D: Connectionless data. Four QoS classes numbered 1, 2, 3, and 4 have been specified with the aim to support service classes A, B, C, and D respectively. An unspecified QoS Class numbered '0' is used for best effort traffic.
INT stnTrafDescrServiceCategory	1.3.6.1.4.1.3551.2.6.1.3.1.1.10	INTEGER	read-only	The ATM service category. Service categories are as follows: other, cbr, rt-vbr, nrt-vbr, abr, ubr
T/F stnTrafDescrFrameDiscard	1.3.6.1.4.1.3551.2.6.1.3.1.1.11	TruthValue	read-only	Whether the network should discard frames rather than cells.
TRA stnTrafDescrOperStatus	1.3.6.1.4.1.3551.2.6.1.3.1.1.12	TrafficDescrOperStatus	read-only	Operational status of the traffic descriptor.
I32 stnTrafDescrCommittedRate	1.3.6.1.4.1.3551.2.6.1.3.1.1.13	Integer32	read-only	The traffic rate in bits per second that the network is committed to transmit for VCs using this transmit traffic descriptor.
I32 stnTrafDescrMaximumRate	1.3.6.1.4.1.3551.2.6.1.3.1.1.14	Integer32	read-only	The maximum traffic rate in bits per second that the network will transmit for VCs using this transmit traffic descriptor, if it differs from the committed rate.
stnAtmPorts	1.3.6.1.4.1.3551.2.6.1.4
stnAtmPortAttrs	1.3.6.1.4.1.3551.2.6.1.4.1
stnAtmPortAttrTable	1.3.6.1.4.1.3551.2.6.1.4.1.1		not-accessible	A list of ATM port attribute entries.
stnAtmPortAttrEntry	1.3.6.1.4.1.3551.2.6.1.4.1.1.1		not-accessible	Entry contains information about a particular ATM port attribute entry.
NUM stnAtmPortIfIndex	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
I32 stnAtmPortIfType	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.2	Integer32	read-only	The interface type of the connection point to the switch fabric. Values are: sonet(1), enet(2), epif(3), rim-enet(4).
INT stnAtmPortIfState	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.3	INTEGER	read-only	The interface state of the connection point to the switch fabric. Values are: not-present(0), detected(1), configured(2), up-non-redundant(3), up-redundant(4), down-non-redundant(5), down-redundant(6), failed(7), initialized(8)
T/F stnAtmPortEnabled	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.4	TruthValue	read-only	Whether the ATM port is enabled.
INT stnAtmPortMinVccVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.5	INTEGER	read-only	Minimum VPI used for Virtual Channel Circuits.
INT stnAtmPortMaxVccVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.6	INTEGER	read-only	Maximum VPI used for Virtual Channel Circuits.
INT stnAtmPortMinVccVci	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.7	INTEGER	read-only	Minimum VCI used for Virtual Channel Circuits. To avoid clashes with the reserved ATM VCI values (such as 5 for signaling and any other reserved values including Connection Manager VCs), the recommended value is 32.
INT stnAtmPortMaxVccVci	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.8	INTEGER	read-only	Maximum VCI used for Virtual Channel Circuits.
INT stnAtmPortMinVpcVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.9	INTEGER	read-only	Minimum VPI used for Virtual Path Circuits. To avoid clashes with the reserved ATM VCCs values (such as 5 for signaling and any other reserved values including Connection Manager VCs), the recommended value is 1.
INT stnAtmPortMaxVpcVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.10	INTEGER	read-only	Maximum VCI used for Virtual Channel Circuits.
INT stnAtmPortMaxActivePaths	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.11	INTEGER	read-only	The maximum number of active paths that can be active at any time on this port.
INT stnAtmPortMaxActiveChannels	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.12	INTEGER	read-only	The maximum number of virtual channels that can be active at any time on this port.
ADR stnAtmPortPVCAddress	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.13	NSAPAddress	read-only	The default configured PVC address information (20-byte NSAP address).
ADR stnAtmPortSVCAddress	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.14	NSAPAddress	read-only	The default configured SVC address information (20-byte NSAP address).
I32 stnAtmPortSigVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.15	Integer32	read-only	The VPI used for the signaling channel.
I32 stnAtmPortSigVci	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.16	Integer32	read-only	The VCI used for the signaling channel.
T/F stnAtmPortSigEnabled	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.17	TruthValue	read-only	Indicates if port will have a signaling stack.
I32 stnAtmPortIlmiVpi	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.18	Integer32	read-only	The VPI used for ILMI channel.
I32 stnAtmPortIlmiVci	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.19	Integer32	read-only	The VCI used for ILMI channel.
T/F stnAtmPortIlmiEnabled	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.20	TruthValue	read-only	Indicates if port will use ILMI.
T/F stnAtmPortOamManagementEnabled	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.21	TruthValue	read-only	Indicates if port is using OAM Management Procedures.
I32 stnAtmPortOamXmtFrequency	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.22	Integer32	read-only	Indicates Frequency of OAM Transmit Cells.
I32 stnAtmPortOamRetryUpCount	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.23	Integer32	read-only	Indicates OAM Cell Retry Up Count value.
I32 stnAtmPortOamRetryDownCount	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.24	Integer32	read-only	Indicates OAM Cell Retry Down Count value.
I32 stnAtmPortOamRetryFrequency	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.25	Integer32	read-only	Indicates OAM Retry Frequency value.
ATM stnAtmPortOperStatus	1.3.6.1.4.1.3551.2.6.1.4.1.1.1.26	AtmPortOperStatus	read-only	Operational status of the Port.
stnAtmPortIlmi	1.3.6.1.4.1.3551.2.6.1.4.2
stnAtmPortIlmiTable	1.3.6.1.4.1.3551.2.6.1.4.2.1		not-accessible	A list of ATM ILMI Port entries.
stnAtmPortIlmiEntry	1.3.6.1.4.1.3551.2.6.1.4.2.1.1		not-accessible	Entry contains information about a particular ATM Port ILMI entry.
NUM stnAtmPortIlmiIfIndex	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
INT stnAtmPortIlmiVersion	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.2	INTEGER	read-only	Specifies the signaling stack protocol type to be used on this port. Valid options are: uni-3-dot-0 uni-3-dot-1 uni-4-dot-0 iisp-3-dot-1
INT stnAtmPortIlmiNetworkOrientation	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.3	INTEGER	read-only	Specifies the ATM device type. Valid options are: user, network
T/F stnAtmPortIlmiAutoNegotiate	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.4	TruthValue	read-only	Indicates ILMI auto negotiation mode
I32 stnAtmPortIlmiPollInterval	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.5	Integer32	read-only	ILMI connection poll interval (S) in seconds. When DC-ILMI is transmitting SNMP Get messages during the attempt to establish connectivity with the remote ILMI component, this parameter determines the time in seconds between transmissions. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).
I32 stnAtmPortIlmiCheckConnectionInt	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.6	Integer32	read-only	ILMI check connection poll interval (T) in seconds. If connectivity checking is enabled (as spec by the value connect in the Admin_Status parameter below), this parameter specifies the time in seconds between successive transmissions of MIB Get msgs for the purpose of detecting loss of ILMI connectivity. If connectivity checking is not enabled, this parameter must be set to zero. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).
I32 stnAtmPortIlmiInactivityFactor	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.7	Integer32	read-only	ILMI inactivity factor (K). The number of consecutive polls for which no response is received from the remote ILMI component before ILMI connectivity is assumed to be lost. The dflt value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).
INT stnAtmPortIlmiLocalConn	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.8	INTEGER	read-only	Specifies whether the local end of the ILMI connection is advertised as a 'public' or 'private' ILMI device. Values are: other, public, private
BIT stnAtmPortIlmiAdminStatus	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.9	Bits	read-only	Specifies which functions of DC-ILMI are enabled. The value std-ilmi must be specified; this value may be combined (using a bitwise OR) with one or more of the following values: std-ilmi - Standard ILMI functions are enabled. addr-reg - Address registration is enabled. connect - Connectivity chcking is enabled (DC-ILMI periodically sends a MIB Get request for the remote system's System ID, to ensure that it can still send and rcvd data on the ILMI connection). Default: (std-ilmi \| addr-reg \| connect)
OID stnAtmPortIlmiEnterprise	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.10	OBJECT IDENTIFIER	read-only	Enterprise Object ID that DC-ILMI will use in building SNMP traps (or other generic MIB traps). This parameter can be used to identify the originator of the trap. The Object ID is specified as an array of unsigned long vals, as follows: The first entry in the array is the length of the array (the num of unsigned long values it contains, including the len value). The second entry in the array is an identifier specifying the Family type of the Object ID. This reps a prefix Object ID; the MIB Sub-Agent is responsible for matching this id with the dotted-decimal notation for this prefix. The remainder of the array gives the index part of the Object ID (the dotted-decimal notation from the end of the Family), with 1 unsigned long for each decimal number in this notation.
OID stnAtmPortIlmiLocalOid	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.11	OBJECT IDENTIFIER	read-only	Object ID identifying the local machine - the first 4 octets indicate the length of the object id. For example, the null object id (0.0), which should be used if no object id is specified, is encoded as 3, 0, 0.
OCT stnAtmPortIlmiNetPrefix	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.12	OCTET STRING	read-only	Default network prefix. If the prefix length is non-zero, ILMI creates an entry in the ILMI NetPrefix Table for this prefix; otherwise the Net_Prefix parameter is not used.
I32 stnAtmPortIlmiPrefixLen	1.3.6.1.4.1.3551.2.6.1.4.2.1.1.13	Integer32	read-only	The length of the default network prefix
stnAtmPortSignaling	1.3.6.1.4.1.3551.2.6.1.4.3
stnAtmPortSigs	1.3.6.1.4.1.3551.2.6.1.4.3.1
stnAtmPortSigTable	1.3.6.1.4.1.3551.2.6.1.4.3.1.1		not-accessible	A list of ATM port signal entries.
stnAtmPortSigEntry	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1		not-accessible	Entry contains information about a particular ATM port signal entry.
NUM stnAtmPortSigIfIndex	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
INT stnAtmPortSigVersion	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.2	INTEGER	read-only	Specifies the signaling stack protocol type to be used on this port. Valid options are: UNI 3.0, UNI 3.1, IISP 3.1, PNNI 1.0
INT stnAtmPortSigNetworkOrientation	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.3	INTEGER	read-only	Indicates whether the ATM device is of the user or network type. Valid values are: user, network
T/F stnAtmPortSigAssignVpiVci	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.4	TruthValue	not-accessible	Specifies whether VPI/VCI assignment is the responsibility of the local signaling stack or of its partner stack. This parameter is used only for UNI 4.0. Values are: true - The local signaling stack is responsible for assigning VPIs/VCIs. false - The parent-signaling stack is responsible for assigning VPIs/VCIs.
INT stnAtmPortSigVpSigType	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.5	INTEGER	read-only	Specifies whether this signaling stack performs VP associated signaling: Valid options are: associated-signaling explicit-vpci
INT stnAtmPortSigParseMode	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.6	INTEGER	read-only	Specifies whether the message parser component of Sig should perform validity checking on the contents of received IEs. This element resides in the CCS MIB to allow software config of this behavior for compliance testing. Values are: normal - The parser checks the contents of the IEs the Sig uses and ensures that they are valid. For other IEs, it checks only the IE type and length and does not parse the contents. strict - The parser checks the contents of addit IEs as well as those used by Signaling and also checks for incorrect repetition of these add it IEs. Errors are handled in the same way as for the IEs used by sig (by sending a status message in UNI 3.1 or by following the IE instruction indicator in UNI 4.0).
T/F stnAtmPortSigPrefCarrierPresent	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.7	TruthValue	read-only	Specifies whether a default prefrd carrier (transit network) is defined. Valid options are: true - the Default_Network_Id below defines which carr is the preferred carrier. false - no default preferred carrier is defined.
T/F stnAtmPortSigPrefCarrier	1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.8	TruthValue	read-only	Specifies the default preferred carrier. If stnAtmPortIlmiPrefCarrierPresent is set to false, this element is not used.
stnAtmPortSigDurations	1.3.6.1.4.1.3551.2.6.1.4.3.2
stnAtmPortSigDurationTable	1.3.6.1.4.1.3551.2.6.1.4.3.2.1		not-accessible	A list of ATM Port Signaling Duration entries.
stnAtmPortSigDurationEntry	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1		not-accessible	Entry contains information about a particular ATM Port Signaling Duration entry.
NUM stnAtmPortSigDurIfIndex	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
I32 stnAtmPortSigT301Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.2	Integer32	read-only	T301 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT303Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.3	Integer32	read-only	T303 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT306Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.4	Integer32	read-only	T306 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT308Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.5	Integer32	read-only	T308 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Intrface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT309Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.6	Integer32	read-only	T309 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT310Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.7	Integer32	read-only	T310 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT313Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.8	Integer32	read-only	T313 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT316Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.9	Integer32	read-only	T316 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT317Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.10	Integer32	read-only	T317 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT322Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.11	Integer32	read-only	T322 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT331Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.12	Integer32	read-only	T331 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT333Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.13	Integer32	read-only	T333 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT397Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.14	Integer32	read-only	T397 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT398Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.15	Integer32	read-only	T398 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigT399Duration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.16	Integer32	read-only	T399 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
I32 stnAtmPortSigSaalRetryDuration	1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.17	Integer32	read-only	SAAL retry duration. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control
stnAtmPortSigRetries	1.3.6.1.4.1.3551.2.6.1.4.3.3
stnAtmPortSigRetryTable	1.3.6.1.4.1.3551.2.6.1.4.3.3.1		not-accessible	A list of ATM Port Signaling retry entries.
stnAtmPortSigRetryEntry	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1		not-accessible	Entry contains information about a ITU-T Q.2931 timer retry counters.
NUM stnAtmPortSigRetryIfIndex	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
I32 stnAtmPortSigT303Retries	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.2	Integer32	read-only	The number of ATM Port Signaling T303 retries.
I32 stnAtmPortSigT308Retries	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.3	Integer32	read-only	The number of ATM Port Signaling T308 retries.
I32 stnAtmPortSigT316Retries	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.4	Integer32	read-only	The number of ATM Port Signaling T316 retries.
I32 stnAtmPortSigT322Retries	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.5	Integer32	read-only	The number of ATM Port Signaling T322 retries.
I32 stnAtmPortSigT331Retries	1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.6	Integer32	read-only	The number of ATM Port Signaling T331 retries.
stnAtmPortSigSSCSTable	1.3.6.1.4.1.3551.2.6.1.4.3.3.2		not-accessible	A list of ATM Port Signaling SSCS entries.
stnAtmPortSigSSCSEntry	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1		not-accessible	Entry contains information about a particular Atm Port Signaling SSCS entry.
NUM stnAtmPortSigSSCSIfIndex	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
I32 stnAtmPortSigSSCSPollDuration	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.2	Integer32	read-only	The duration of the SSCS Poll timer in milliseconds.
I32 stnAtmPortSigSSCSKeepAliveDuration	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.3	Integer32	read-only	The duration of the SSCS keep-alive timer in milliseconds.
I32 stnAtmPortSigSSCSIdleDuration	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.4	Integer32	read-only	The duration of the SSCS idle timer in milliseconds.
I32 stnAtmPortSigSSCSNoRspDuration	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.5	Integer32	read-only	The duration of the SSCS no-response timer in milliseconds.
I32 stnAtmPortSigSSCSCcDuration	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.6	Integer32	read-only	The duration of the SSCS CC timer in milliseconds.
I32 stnAtmPortSigSSCSMaxRcvWindowSize	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.7	Integer32	read-only	The maximum size on a receive window.
I32 stnAtmPortSigSSCSMaxCcRetries	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.8	Integer32	read-only	The maximum number of expiries and subsequent connection control PDU retransmissions acceptable before closing the connection.
I32 stnAtmPortSigSSCSMaxSdBetwPolls	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.9	Integer32	read-only	The maximum number of STAT list elements in a STAT PDU.
I32 stnAtmPortSigSSCSMaxStatListElms	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.10	Integer32	read-only	The maximum number of STAT list elements in a STAT PDU.
T/F stnAtmPortSigSSCSPollAfterRetrans	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.11	TruthValue	read-only	Whether to send a POLL after retransmitting PDUs.
T/F stnAtmPortSigSSCSRepeatUstat	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.12	TruthValue	read-only	QSAAL only: if true, send two USTATs each time a USTAT is sent.
T/F stnAtmPortSigSSCSUstatRspToPoll	1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.13	TruthValue	read-only	QSAAL only: whether USTAT PDUs are issued in response to POLLs.
stnAtmPortTraffic	1.3.6.1.4.1.3551.2.6.1.4.4
stnAtmPortTrafficTable	1.3.6.1.4.1.3551.2.6.1.4.4.1		not-accessible	A list of ATM port traffic entries.
stnAtmPortTrafficEntry	1.3.6.1.4.1.3551.2.6.1.4.4.1.1		not-accessible	Entry contains information about a particular ATM port traffic entry.
NUM stnAtmPortTrafIndex	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
C32 stnAtmPortTrafTxCellsEx	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.2	Counter32	read-only	The number of ATM cells transmitted.
C32 stnAtmPortTrafRxCells	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.3	Counter32	read-only	The number of ATM cells received.
C32 stnAtmPortTrafTxParityErrors	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.4	Counter32	read-only	The number of ATM transmit parity errors.
C32 stnAtmPortTrafRxHdrChkSumErrors	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.5	Counter32	read-only	The number of received ATM header checksum errors.
C32 stnAtmPortTrafPhyParityErrors	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.6	Counter32	read-only	The number of ATM physical parity errors.
C32 stnAtmPortTrafCrc10Errors	1.3.6.1.4.1.3551.2.6.1.4.4.1.1.7	Counter32	read-only	The number of ATM CRC-10 errors.
stnAtmTraces	1.3.6.1.4.1.3551.2.6.1.5
stnTraceIps	1.3.6.1.4.1.3551.2.6.1.5.1
T/F stnTraceIpsEnabled	1.3.6.1.4.1.3551.2.6.1.5.1.1	TruthValue	read-only	Specifies whether IPS tracing is enabled.
I32 stnTraceIpsSize	1.3.6.1.4.1.3551.2.6.1.5.1.2	Integer32	read-only	Specifies the maximum IPS trace buffer size multipled by 1024. The IPS trace log file will wrap when it reaches the maximum. Default: 1000 x 1024 Lines
OCT stnTraceIpsFile	1.3.6.1.4.1.3551.2.6.1.5.1.3	OCTET STRING	read-only	Specifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted (close file and open new).
stnTracePd	1.3.6.1.4.1.3551.2.6.1.5.2
T/F stnTracePdProblemEnabled	1.3.6.1.4.1.3551.2.6.1.5.2.1	TruthValue	read-only	Specifies whether PD problem tracing is enabled.
T/F stnTracePdExceptionEnabled	1.3.6.1.4.1.3551.2.6.1.5.2.2	TruthValue	read-only	Specifies whether PD exception tracing is enabled.
T/F stnTracePdAuditEnabled	1.3.6.1.4.1.3551.2.6.1.5.2.3	TruthValue	read-only	Specifies whether PD audit tracing is enabled.
T/F stnTracePdDeveloperEnabled	1.3.6.1.4.1.3551.2.6.1.5.2.4	TruthValue	read-only	Specifies whether PD developer tracing is enabled.
I32 stnTracePdSize	1.3.6.1.4.1.3551.2.6.1.5.2.5	Integer32	read-only	Specifies the maximum PD trace buffer size multipled by 1024. The PD trace log file will wrap when it reaches the maximum.
OCT stnTracePdFile	1.3.6.1.4.1.3551.2.6.1.5.2.6	OCTET STRING	read-only	Specifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted.
stnAtmQos	1.3.6.1.4.1.3551.2.6.1.6
stnQosCLR	1.3.6.1.4.1.3551.2.6.1.6.1
I32 stnQosClass1CLR	1.3.6.1.4.1.3551.2.6.1.6.1.1	Integer32	read-only	QoS Class 1 cell loss ratio.
I32 stnQosClass2CLR	1.3.6.1.4.1.3551.2.6.1.6.1.2	Integer32	read-only	QoS Class 2 cell loss ratio.
I32 stnQosClass3CLR	1.3.6.1.4.1.3551.2.6.1.6.1.3	Integer32	read-only	QoS Class 3 cell loss ratio.
I32 stnQosClass4CLR	1.3.6.1.4.1.3551.2.6.1.6.1.4	Integer32	read-only	QoS Class 4 cell loss ratio.
stnQosCDV	1.3.6.1.4.1.3551.2.6.1.6.2
I32 stnQosClass1CDV	1.3.6.1.4.1.3551.2.6.1.6.2.1	Integer32	read-only	QoS Class 1 cell delay variation.
I32 stnQosClass2CDV	1.3.6.1.4.1.3551.2.6.1.6.2.2	Integer32	read-only	QoS Class 2 cell delay variation.
I32 stnQosClass3CDV	1.3.6.1.4.1.3551.2.6.1.6.2.3	Integer32	read-only	QoS Class 3 cell delay variation.
I32 stnQosClass4CDV	1.3.6.1.4.1.3551.2.6.1.6.2.4	Integer32	read-only	QoS Class 4 cell delay variation.
stnQosCTD	1.3.6.1.4.1.3551.2.6.1.6.3
I32 stnQosClass1MaxCTD	1.3.6.1.4.1.3551.2.6.1.6.3.1	Integer32	read-only	QoS Class 1 cell transfer delay.
I32 stnQosClass2MaxCTD	1.3.6.1.4.1.3551.2.6.1.6.3.2	Integer32	read-only	QoS Class 2 cell transfer delay.
I32 stnQosClass3MaxCTD	1.3.6.1.4.1.3551.2.6.1.6.3.3	Integer32	read-only	QoS Class 3 cell delay transfer.
I32 stnQosClass4MaxCTD	1.3.6.1.4.1.3551.2.6.1.6.3.4	Integer32	read-only	QoS Class 4 cell delay transfer.
stnAtmAddresses	1.3.6.1.4.1.3551.2.6.1.7
stnAtmAddressTable	1.3.6.1.4.1.3551.2.6.1.7.1		not-accessible	A list of ATM address entries.
stnAtmAddressEntry	1.3.6.1.4.1.3551.2.6.1.7.1.1		not-accessible	Entry contains information about a particular session.
NUM stnAtmAddrIfIndex	1.3.6.1.4.1.3551.2.6.1.7.1.1.1	InterfaceIndex	read-only	The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.
ADR stnAtmAddrAddress	1.3.6.1.4.1.3551.2.6.1.7.1.1.2	NSAPAddress	read-only	The value of the ATM NSAP address.
I32 stnAtmAddrAddressLen	1.3.6.1.4.1.3551.2.6.1.7.1.1.3	Integer32	read-only	The number of relevent bits in the ATM address.
stnAtmThresholds	1.3.6.1.4.1.3551.2.6.1.8
stnAtmThresholdTable	1.3.6.1.4.1.3551.2.6.1.8.1		not-accessible	A list of ATM threshold entries.
stnAtmThresholdEntry	1.3.6.1.4.1.3551.2.6.1.8.1.1		not-accessible	Entry contains information about a particular ATM threshold entry.
INT stnAtmTholdTgrpId	1.3.6.1.4.1.3551.2.6.1.8.1.1.1	INTEGER	read-only	Specifies the threshold group indentifier.
INT stnAtmTholdRegionId	1.3.6.1.4.1.3551.2.6.1.8.1.1.2	INTEGER	read-only	Region identifier within a threshold group.
INT stnAtmTholdCellLowerLimit	1.3.6.1.4.1.3551.2.6.1.8.1.1.3	INTEGER	read-only	Lower Cell number limit for region.
INT stnAtmTholdCellUpperLimit	1.3.6.1.4.1.3551.2.6.1.8.1.1.4	INTEGER	read-only	Upper Cell number limit for region.
INT stnAtmTholdCellQLimitMarking	1.3.6.1.4.1.3551.2.6.1.8.1.1.5	INTEGER	read-only	Queue limit for any flow above which EFCI marking occurs.
INT stnAtmTholdQLimitDiscard	1.3.6.1.4.1.3551.2.6.1.8.1.1.6	INTEGER	read-only	Queue limit for any flow above which Discard processing occurs.
INT stnAtmTholdQueueLimit	1.3.6.1.4.1.3551.2.6.1.8.1.1.7	INTEGER	read-only	Queue limit for any flow above which cells are automatically discarded.
stnAtmAcct	1.3.6.1.4.1.3551.2.6.1.9
T/F stnAtmAcctEnabled	1.3.6.1.4.1.3551.2.6.1.9.1	TruthValue	read-only	Specifies whether account logging is turned on or off.
I32 stnAtmAcctMaxSize	1.3.6.1.4.1.3551.2.6.1.9.2	Integer32	read-only	Specifies the maximum accounting log buffer size. in Kbytes. The accounting log file will be closed when it reaches the maximum size and the name appended with a numeric differentiation.
I32 stnAtmAcctMaxFiles	1.3.6.1.4.1.3551.2.6.1.9.3	Integer32	read-only	Specifies the maximum number of history files to be stored. Once the maximum number of files is reached, the oldest file is deleted.
OCT stnAtmAcctFilePath	1.3.6.1.4.1.3551.2.6.1.9.4	OCTET STRING	read-only	Specifies the accounting log output path and file name on remote device.
IP stnAtmAcctFtpServer1	1.3.6.1.4.1.3551.2.6.1.9.5	IpAddress	read-only	The IP address of the first remote FTP server.
STR stnAtmAcctFtpUserName1	1.3.6.1.4.1.3551.2.6.1.9.6	DisplayString	read-only	The first FTP server username.
OCT stnAtmAcctFtpPassword1	1.3.6.1.4.1.3551.2.6.1.9.7	OCTET STRING	not-accessible	The first FTP server password.
IP stnAtmAcctFtpServer2	1.3.6.1.4.1.3551.2.6.1.9.8	IpAddress	read-only	The IP address of the second remote FTP server.
STR stnAtmAcctFtpUserName2	1.3.6.1.4.1.3551.2.6.1.9.9	DisplayString	read-only	The second FTP server username.
OCT stnAtmAcctFtpPassword2	1.3.6.1.4.1.3551.2.6.1.9.10	OCTET STRING	not-accessible	The second FTP server password.
IP stnAtmAcctFtpServer3	1.3.6.1.4.1.3551.2.6.1.9.11	IpAddress	read-only	The IP address of the third remote FTP server.
STR stnAtmAcctFtpUserName3	1.3.6.1.4.1.3551.2.6.1.9.12	DisplayString	read-only	The third FTP server username.
OCT stnAtmAcctFtpPassword3	1.3.6.1.4.1.3551.2.6.1.9.13	OCTET STRING	not-accessible	The third FTP server password.
IP stnAtmAcctCurrentFtpServer	1.3.6.1.4.1.3551.2.6.1.9.14	IpAddress	read-only	The IP address of the current FTP server.
IP stnAtmAcctPreviousFtpServer	1.3.6.1.4.1.3551.2.6.1.9.15	IpAddress	read-only	The IP address of the previous FTP server.
stnAtmMibConformance	1.3.6.1.4.1.3551.2.6.2
NTF stnCdrServerFailure	1.3.6.1.4.1.3551.2.100.0.15			A stnCdrServerFailure trap signifies that the agent entity has detected that the accounting server has failed over to an auxilary server. The generation of this trap can be controlled by the stnNotificationEnableCdrServerFailure object in this MIB.
NTF stnCdrLogFailure	1.3.6.1.4.1.3551.2.100.0.16			A stnCdrLogFailure trap signifies that the agent entity has detected that all accounting servers are inaccessible. Accounting data could be lost. The generation of this trap can be controlled by the stnNotificationEnableCdrLogFailure object in this MIB.
NTF stnConfigAuditPvcFailure	1.3.6.1.4.1.3551.2.100.0.31			A stnConfigAuditPvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured PVC after a failover. The generation of this trap can be controlled by the CfgAuditPvcTraps configuration object.
NTF stnConfigAuditSpvcFailure	1.3.6.1.4.1.3551.2.100.0.32			A stnConfigAuditSpvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured SPVC after a failover. The generation of this trap can be controlled by the CfgAuditSpvcTraps configuration object.

RFC description

Spring Tide Networks ATM MIB covering links, cross-connections, traffic descriptors, ports, QoS, and thresholds.

Start monitoring Spring Tide Networks broadband aggregation devices with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download STN-ATM-MIB