STN-ROUTER-MIB

All MIBs › STN-ROUTER-MIB

Organization: Spring Tide Networks, Inc.

Last Updated: 2000-02-16

Category: Routing, Spring Tide Networks

Description:

Manages Spring Tide Networks router-level configuration, protocol instances, and forwarding parameters.

Imported Objects

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION

From SPRING-TIDE-NETWORKS-SMI

stnNotification	OBJECT-IDENTITY
stnSystems	OBJECT-IDENTITY

From STN-CHASSIS-MIB

stnEngineCpu	OBJECT-TYPE
stnEngineIndex	OBJECT-TYPE
stnEngineSlot	OBJECT-TYPE

What Is STN-ROUTER-MIB?

STN-ROUTER-MIB is a Spring Tide Networks MIB for managing router-level configuration, virtual router instances, and associated protocol interfaces (IP, PPP, and PPPoE) on Spring Tide carrier routing platforms. It covers configuration and forwarding parameters for virtual routers along with their layered protocol interface stacks. Its role in status monitoring centers on software/configuration health—tracking virtual router instance state and the operational status of the IP/PPP/PPPoE interfaces bound to each router—rather than physical environmental sensors. As a router-focused module it likely depends on or complements standard interface MIBs (IF-MIB) and PPP-related standards for the protocol layers it references. It is deployed on Spring Tide Networks multiservice routing platforms used by service providers for broadband/subscriber aggregation. Since little vendor documentation accompanies most public STN-ROUTER-MIB downloads, administrators often have to infer exact object names by walking the MIB tree directly on a live Spring Tide device.

IPNetwork Monitor allows you to monitor SNMP objects defined in STN-ROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

virtual router status
IP interface state
PPP interface state
PPPoE session state

Supported Devices

Spring Tide Networks routing platform

Monitoring Examples

No sample object names were provided for this module, so specific object polling cannot be illustrated concretely; based on the module description, an admin would typically monitor the operational status of each virtual router instance and its bound PPP/PPPoE sessions to detect subscriber session failures or router-instance faults. Given the module's stated scope (virtual routers plus IP, PPP, and PPPOE interfaces), expected monitorable items would include virtual router state and per-interface protocol status, though exact object names cannot be confirmed without the MIB source.

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF stnConfigAuditPppIfFailure	1.3.6.1.4.1.3551.2.100.0.36			A stnConfigAuditPppIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPP interface after a failover. The generation of this trap can be controlled by the CfgAuditPppIfTraps configuration object.
NTF stnConfigAuditPppoeIfFailure	1.3.6.1.4.1.3551.2.100.0.35			A stnConfigAuditPppoeIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPPOE interface after a failover. The generation of this trap can be controlled by the CfgAuditPppoeIfTraps configuration object.
NTF stnConfigAuditRouterFailure	1.3.6.1.4.1.3551.2.100.0.33			A stnConfigAuditRouterFailure trap signifies that the agent entity has detected an inconsistency between an active and configured routers after a failover. The generation of this trap can be controlled by the CfgAuditRouterTraps configuration object.
NTF stnConfigAuditSubnetIfFailure	1.3.6.1.4.1.3551.2.100.0.34			A stnConfigAuditSubnetIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured subnet interface after a failover. The generation of this trap can be controlled by the CfgAuditSubnetIfTraps configuration object.
stnPppEntry	1.3.6.1.4.1.3551.2.7.1.4.1		not-accessible	Entry contains information about a particular session.
NUM stnPppIfIndex	1.3.6.1.4.1.3551.2.7.1.4.1.5	InterfaceIndex	read-only	The ifindex.
I32 stnPppIndex	1.3.6.1.4.1.3551.2.7.1.4.1.1	Integer32	read-only	A sequence number that identifies a PPP interface entry in the table.
stnPppoeEntry	1.3.6.1.4.1.3551.2.7.1.3.1		not-accessible	Entry contains information about a particular PPPOE interface.
NUM stnPppoeIfIndex	1.3.6.1.4.1.3551.2.7.1.3.1.5	InterfaceIndex	read-only	The ifindex.
I32 stnPppoeIndex	1.3.6.1.4.1.3551.2.7.1.3.1.1	Integer32	read-only	A sequence number that identifies a PPPOE interface entry in the table.
I32 stnPppoeLinkInstance	1.3.6.1.4.1.3551.2.7.1.3.1.8	Integer32	read-only	The instance of the configuration record for the link the PPPoE interface is configured over.
INT stnPppoeLinkType	1.3.6.1.4.1.3551.2.7.1.3.1.7	INTEGER	read-only	Indicates the type of link the PPPoE interface is configured over.
I32 stnPppoeRouterIndex	1.3.6.1.4.1.3551.2.7.1.3.1.6	Integer32	read-only	The router this PPPOE interface is associated with.
OPE stnPppoeState	1.3.6.1.4.1.3551.2.7.1.3.1.3	OperationState	read-only	The operational state of the PPPOE interface.
stnPppoeTable	1.3.6.1.4.1.3551.2.7.1.3		not-accessible	A list of PPPOE interface entries.
NUM stnPppoeType	1.3.6.1.4.1.3551.2.7.1.3.1.2	InterfaceConnectionType	read-only	The interface type.
I32 stnPppoeVclid	1.3.6.1.4.1.3551.2.7.1.3.1.4	Integer32	read-only	The vcl ID associated with this PPPOE interface.
I32 stnPppRouterIndex	1.3.6.1.4.1.3551.2.7.1.4.1.6	Integer32	read-only	The router this PPP interface is associated with.
OPE stnPppState	1.3.6.1.4.1.3551.2.7.1.4.1.3	OperationState	read-only	The operational state or the PPP interface.
stnPppTable	1.3.6.1.4.1.3551.2.7.1.4		not-accessible	A list of PPP interface entries.
NUM stnPppType	1.3.6.1.4.1.3551.2.7.1.4.1.2	InterfaceConnectionType	read-only	The interface type.
I32 stnPppVclid	1.3.6.1.4.1.3551.2.7.1.4.1.4	Integer32	read-only	The vcl ID associated with this PPP interface.
stnRouter	1.3.6.1.4.1.3551.2.7			This MIB module describes managed objects of Spring Tide Networks virtual routers plus associated IP, PPP, and PPPOE interfaces.
I32 stnRouterActiveCpu	1.3.6.1.4.1.3551.2.7.1.1.1.10	Integer32	read-only	The CPU to which this router is currently assigned.
I32 stnRouterActiveSlot	1.3.6.1.4.1.3551.2.7.1.1.1.9	Integer32	read-only	The slot/module to which this router is currently assigned.
stnRouterAtmVpn	1.3.6.1.4.1.3551.2.7.1.7
I32 stnRouterConfiguredCpu	1.3.6.1.4.1.3551.2.7.1.1.1.12	Integer32	read-only	The configured CPU for this router.
I32 stnRouterConfiguredSlot	1.3.6.1.4.1.3551.2.7.1.1.1.11	Integer32	read-only	The configured slot/module for this router.
INT stnRouterDefaultPolicyAction	1.3.6.1.4.1.3551.2.7.1.1.1.18	INTEGER	read-only	Action to take when a packet does not match any policies.
NTF stnRouterDown	1.3.6.1.4.1.3551.2.100.0.27			A stnRouterDown trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterDownTraps configuration object.
INT stnRouterEnabled	1.3.6.1.4.1.3551.2.7.1.1.1.6	INTEGER	read-only	The variable to indicate if this router is enabled.
I32 stnRouterEngineID	1.3.6.1.4.1.3551.2.7.1.1.1.4	Integer32	read-only	The engine to which this router is currently assigned.
stnRouterEntry	1.3.6.1.4.1.3551.2.7.1.1.1		not-accessible	Entry contains information about a particular router.
IP stnRouterHomeIpAddress	1.3.6.1.4.1.3551.2.7.1.1.1.5	IpAddress	read-only	The Home IP address of this router.
I32 stnRouterIndex	1.3.6.1.4.1.3551.2.7.1.1.1.1	Integer32	read-only	A sequence number that identifies a router entry in the table.
stnRouterMibConformance	1.3.6.1.4.1.3551.2.7.2
STR stnRouterName	1.3.6.1.4.1.3551.2.7.1.1.1.7	DisplayString	read-only	The name of this router.
stnRouterNAT	1.3.6.1.4.1.3551.2.7.1.5
stnRouterObjects	1.3.6.1.4.1.3551.2.7.1
NTF stnRouterReassigned	1.3.6.1.4.1.3551.2.100.0.28			A stnRouterReassigned trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the the assigned(1) state for one of its routers. The generation of this trap can be controlled by the RouterReassignedTraps configuration object.
NTF stnRouterReassignFailure	1.3.6.1.4.1.3551.2.100.0.29			A stnRouterReassignFailure trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterReassignFailureTraps configuration object.
INT stnRouterReassignOnFault	1.3.6.1.4.1.3551.2.7.1.1.1.15	INTEGER	read-only	The variable to indicate if this router should be reassigned if the module where to fail.
I32 stnRouterServiceDomain	1.3.6.1.4.1.3551.2.7.1.1.1.17	Integer32	read-only	The service domain to which this router belongs.
STR stnRouterServiceName	1.3.6.1.4.1.3551.2.7.1.1.1.16	DisplayString	read-only	The service to which this router belongs.
I32 stnRouterStandbyCpu	1.3.6.1.4.1.3551.2.7.1.1.1.14	Integer32	read-only	The standby CPU for this router.
I32 stnRouterStandbySlot	1.3.6.1.4.1.3551.2.7.1.1.1.13	Integer32	read-only	The standby slot/module for this router.
OPE stnRouterState	1.3.6.1.4.1.3551.2.7.1.1.1.3	OperationState	read-only	The operational state of the router.
stnRouterTable	1.3.6.1.4.1.3551.2.7.1.1		not-accessible	A list of router entries.
INT stnRouterType	1.3.6.1.4.1.3551.2.7.1.1.1.2	INTEGER	read-only	The router type.
NTF stnRouterUp	1.3.6.1.4.1.3551.2.100.0.26			A stnRouterUp trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the assigned(4) state for one of its routers. The generation of this trap can be controlled by the RouterUpTraps configuration object.
TIK stnRouterUpTime	1.3.6.1.4.1.3551.2.7.1.1.1.8	TimeTicks	read-only	The time (in hundredths of a second) since the router was last re-initialized.
stnRouterVEI	1.3.6.1.4.1.3551.2.7.1.6
stnRouterVimuxMpls	1.3.6.1.4.1.3551.2.7.1.8
stnRouterVTI	1.3.6.1.4.1.3551.2.7.1.9
NTF stnSubnetIfAssignFailure	1.3.6.1.4.1.3551.2.100.0.30			A stnSubnetIfAssignFailure trap signifies that the agent entity has detected that the stnSubnetInterfaceState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its interfaces. The generation of this trap can be controlled by the stnEnableSubnetInterfaceTraps configuration object.
IP stnSubnetInterfaceAddress	1.3.6.1.4.1.3551.2.7.1.2.1.3	IpAddress	read-only	The IP address of this interface.
INT stnSubnetInterfaceEnabled	1.3.6.1.4.1.3551.2.7.1.2.1.2	INTEGER	read-only	Enable or disable the sub-network interface.
stnSubnetInterfaceEntry	1.3.6.1.4.1.3551.2.7.1.2.1		not-accessible	Entry contains information about a particular sub-network interface.
IP stnSubnetInterfaceForcedNextHop	1.3.6.1.4.1.3551.2.7.1.2.1.11	IpAddress	read-only	The IP address of the next hop router that all IP traffic received on this interface will be sent to
U32 stnSubnetInterfaceIndex	1.3.6.1.4.1.3551.2.7.1.2.1.1	Unsigned32	read-only	A sequence number that identifies a sub-network interface entry in the table.
I32 stnSubnetInterfaceLinkInstance	1.3.6.1.4.1.3551.2.7.1.2.1.10	Integer32	read-only	The instance of the configuration record for the link the subnet interface is configured over.
INT stnSubnetInterfaceLinkType	1.3.6.1.4.1.3551.2.7.1.2.1.9	INTEGER	read-only	Indicates the type of link the subnet interface is configured over.
IP stnSubnetInterfaceMask	1.3.6.1.4.1.3551.2.7.1.2.1.4	IpAddress	read-only	The sub-network mask of this interface.
I32 stnSubnetInterfaceRouterIndex	1.3.6.1.4.1.3551.2.7.1.2.1.8	Integer32	read-only	The router this sub-network interface is associated with.
STR stnSubnetInterfaceServiceName	1.3.6.1.4.1.3551.2.7.1.2.1.12	DisplayString	read-only	The service to which this interface belongs.
OPE stnSubnetInterfaceState	1.3.6.1.4.1.3551.2.7.1.2.1.7	OperationState	read-only	The operational state of the sub-network interface.
stnSubnetInterfaceTable	1.3.6.1.4.1.3551.2.7.1.2		not-accessible	A list of sub-network interface entries.
NUM stnSubnetInterfaceType	1.3.6.1.4.1.3551.2.7.1.2.1.6	InterfaceConnectionType	read-only	The interface type.
I32 stnSubnetInterfaceVclid	1.3.6.1.4.1.3551.2.7.1.2.1.5	Integer32	read-only	The vcl ID associated with this sub-network interface.

OID symbolic	OID numeric	Type	Access	Description
stnRouter	1.3.6.1.4.1.3551.2.7			This MIB module describes managed objects of Spring Tide Networks virtual routers plus associated IP, PPP, and PPPOE interfaces.
stnRouterObjects	1.3.6.1.4.1.3551.2.7.1
stnRouterTable	1.3.6.1.4.1.3551.2.7.1.1		not-accessible	A list of router entries.
stnRouterEntry	1.3.6.1.4.1.3551.2.7.1.1.1		not-accessible	Entry contains information about a particular router.
I32 stnRouterIndex	1.3.6.1.4.1.3551.2.7.1.1.1.1	Integer32	read-only	A sequence number that identifies a router entry in the table.
INT stnRouterType	1.3.6.1.4.1.3551.2.7.1.1.1.2	INTEGER	read-only	The router type.
OPE stnRouterState	1.3.6.1.4.1.3551.2.7.1.1.1.3	OperationState	read-only	The operational state of the router.
I32 stnRouterEngineID	1.3.6.1.4.1.3551.2.7.1.1.1.4	Integer32	read-only	The engine to which this router is currently assigned.
IP stnRouterHomeIpAddress	1.3.6.1.4.1.3551.2.7.1.1.1.5	IpAddress	read-only	The Home IP address of this router.
INT stnRouterEnabled	1.3.6.1.4.1.3551.2.7.1.1.1.6	INTEGER	read-only	The variable to indicate if this router is enabled.
STR stnRouterName	1.3.6.1.4.1.3551.2.7.1.1.1.7	DisplayString	read-only	The name of this router.
TIK stnRouterUpTime	1.3.6.1.4.1.3551.2.7.1.1.1.8	TimeTicks	read-only	The time (in hundredths of a second) since the router was last re-initialized.
I32 stnRouterActiveSlot	1.3.6.1.4.1.3551.2.7.1.1.1.9	Integer32	read-only	The slot/module to which this router is currently assigned.
I32 stnRouterActiveCpu	1.3.6.1.4.1.3551.2.7.1.1.1.10	Integer32	read-only	The CPU to which this router is currently assigned.
I32 stnRouterConfiguredSlot	1.3.6.1.4.1.3551.2.7.1.1.1.11	Integer32	read-only	The configured slot/module for this router.
I32 stnRouterConfiguredCpu	1.3.6.1.4.1.3551.2.7.1.1.1.12	Integer32	read-only	The configured CPU for this router.
I32 stnRouterStandbySlot	1.3.6.1.4.1.3551.2.7.1.1.1.13	Integer32	read-only	The standby slot/module for this router.
I32 stnRouterStandbyCpu	1.3.6.1.4.1.3551.2.7.1.1.1.14	Integer32	read-only	The standby CPU for this router.
INT stnRouterReassignOnFault	1.3.6.1.4.1.3551.2.7.1.1.1.15	INTEGER	read-only	The variable to indicate if this router should be reassigned if the module where to fail.
STR stnRouterServiceName	1.3.6.1.4.1.3551.2.7.1.1.1.16	DisplayString	read-only	The service to which this router belongs.
I32 stnRouterServiceDomain	1.3.6.1.4.1.3551.2.7.1.1.1.17	Integer32	read-only	The service domain to which this router belongs.
INT stnRouterDefaultPolicyAction	1.3.6.1.4.1.3551.2.7.1.1.1.18	INTEGER	read-only	Action to take when a packet does not match any policies.
stnSubnetInterfaceTable	1.3.6.1.4.1.3551.2.7.1.2		not-accessible	A list of sub-network interface entries.
stnSubnetInterfaceEntry	1.3.6.1.4.1.3551.2.7.1.2.1		not-accessible	Entry contains information about a particular sub-network interface.
U32 stnSubnetInterfaceIndex	1.3.6.1.4.1.3551.2.7.1.2.1.1	Unsigned32	read-only	A sequence number that identifies a sub-network interface entry in the table.
INT stnSubnetInterfaceEnabled	1.3.6.1.4.1.3551.2.7.1.2.1.2	INTEGER	read-only	Enable or disable the sub-network interface.
IP stnSubnetInterfaceAddress	1.3.6.1.4.1.3551.2.7.1.2.1.3	IpAddress	read-only	The IP address of this interface.
IP stnSubnetInterfaceMask	1.3.6.1.4.1.3551.2.7.1.2.1.4	IpAddress	read-only	The sub-network mask of this interface.
I32 stnSubnetInterfaceVclid	1.3.6.1.4.1.3551.2.7.1.2.1.5	Integer32	read-only	The vcl ID associated with this sub-network interface.
NUM stnSubnetInterfaceType	1.3.6.1.4.1.3551.2.7.1.2.1.6	InterfaceConnectionType	read-only	The interface type.
OPE stnSubnetInterfaceState	1.3.6.1.4.1.3551.2.7.1.2.1.7	OperationState	read-only	The operational state of the sub-network interface.
I32 stnSubnetInterfaceRouterIndex	1.3.6.1.4.1.3551.2.7.1.2.1.8	Integer32	read-only	The router this sub-network interface is associated with.
INT stnSubnetInterfaceLinkType	1.3.6.1.4.1.3551.2.7.1.2.1.9	INTEGER	read-only	Indicates the type of link the subnet interface is configured over.
I32 stnSubnetInterfaceLinkInstance	1.3.6.1.4.1.3551.2.7.1.2.1.10	Integer32	read-only	The instance of the configuration record for the link the subnet interface is configured over.
IP stnSubnetInterfaceForcedNextHop	1.3.6.1.4.1.3551.2.7.1.2.1.11	IpAddress	read-only	The IP address of the next hop router that all IP traffic received on this interface will be sent to
STR stnSubnetInterfaceServiceName	1.3.6.1.4.1.3551.2.7.1.2.1.12	DisplayString	read-only	The service to which this interface belongs.
stnPppoeTable	1.3.6.1.4.1.3551.2.7.1.3		not-accessible	A list of PPPOE interface entries.
stnPppoeEntry	1.3.6.1.4.1.3551.2.7.1.3.1		not-accessible	Entry contains information about a particular PPPOE interface.
I32 stnPppoeIndex	1.3.6.1.4.1.3551.2.7.1.3.1.1	Integer32	read-only	A sequence number that identifies a PPPOE interface entry in the table.
NUM stnPppoeType	1.3.6.1.4.1.3551.2.7.1.3.1.2	InterfaceConnectionType	read-only	The interface type.
OPE stnPppoeState	1.3.6.1.4.1.3551.2.7.1.3.1.3	OperationState	read-only	The operational state of the PPPOE interface.
I32 stnPppoeVclid	1.3.6.1.4.1.3551.2.7.1.3.1.4	Integer32	read-only	The vcl ID associated with this PPPOE interface.
NUM stnPppoeIfIndex	1.3.6.1.4.1.3551.2.7.1.3.1.5	InterfaceIndex	read-only	The ifindex.
I32 stnPppoeRouterIndex	1.3.6.1.4.1.3551.2.7.1.3.1.6	Integer32	read-only	The router this PPPOE interface is associated with.
INT stnPppoeLinkType	1.3.6.1.4.1.3551.2.7.1.3.1.7	INTEGER	read-only	Indicates the type of link the PPPoE interface is configured over.
I32 stnPppoeLinkInstance	1.3.6.1.4.1.3551.2.7.1.3.1.8	Integer32	read-only	The instance of the configuration record for the link the PPPoE interface is configured over.
stnPppTable	1.3.6.1.4.1.3551.2.7.1.4		not-accessible	A list of PPP interface entries.
stnPppEntry	1.3.6.1.4.1.3551.2.7.1.4.1		not-accessible	Entry contains information about a particular session.
I32 stnPppIndex	1.3.6.1.4.1.3551.2.7.1.4.1.1	Integer32	read-only	A sequence number that identifies a PPP interface entry in the table.
NUM stnPppType	1.3.6.1.4.1.3551.2.7.1.4.1.2	InterfaceConnectionType	read-only	The interface type.
OPE stnPppState	1.3.6.1.4.1.3551.2.7.1.4.1.3	OperationState	read-only	The operational state or the PPP interface.
I32 stnPppVclid	1.3.6.1.4.1.3551.2.7.1.4.1.4	Integer32	read-only	The vcl ID associated with this PPP interface.
NUM stnPppIfIndex	1.3.6.1.4.1.3551.2.7.1.4.1.5	InterfaceIndex	read-only	The ifindex.
I32 stnPppRouterIndex	1.3.6.1.4.1.3551.2.7.1.4.1.6	Integer32	read-only	The router this PPP interface is associated with.
stnRouterNAT	1.3.6.1.4.1.3551.2.7.1.5
stnRouterVEI	1.3.6.1.4.1.3551.2.7.1.6
stnRouterAtmVpn	1.3.6.1.4.1.3551.2.7.1.7
stnRouterVimuxMpls	1.3.6.1.4.1.3551.2.7.1.8
stnRouterVTI	1.3.6.1.4.1.3551.2.7.1.9
stnRouterMibConformance	1.3.6.1.4.1.3551.2.7.2
NTF stnRouterUp	1.3.6.1.4.1.3551.2.100.0.26			A stnRouterUp trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the assigned(4) state for one of its routers. The generation of this trap can be controlled by the RouterUpTraps configuration object.
NTF stnRouterDown	1.3.6.1.4.1.3551.2.100.0.27			A stnRouterDown trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterDownTraps configuration object.
NTF stnRouterReassigned	1.3.6.1.4.1.3551.2.100.0.28			A stnRouterReassigned trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the the assigned(1) state for one of its routers. The generation of this trap can be controlled by the RouterReassignedTraps configuration object.
NTF stnRouterReassignFailure	1.3.6.1.4.1.3551.2.100.0.29			A stnRouterReassignFailure trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterReassignFailureTraps configuration object.
NTF stnSubnetIfAssignFailure	1.3.6.1.4.1.3551.2.100.0.30			A stnSubnetIfAssignFailure trap signifies that the agent entity has detected that the stnSubnetInterfaceState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its interfaces. The generation of this trap can be controlled by the stnEnableSubnetInterfaceTraps configuration object.
NTF stnConfigAuditRouterFailure	1.3.6.1.4.1.3551.2.100.0.33			A stnConfigAuditRouterFailure trap signifies that the agent entity has detected an inconsistency between an active and configured routers after a failover. The generation of this trap can be controlled by the CfgAuditRouterTraps configuration object.
NTF stnConfigAuditSubnetIfFailure	1.3.6.1.4.1.3551.2.100.0.34			A stnConfigAuditSubnetIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured subnet interface after a failover. The generation of this trap can be controlled by the CfgAuditSubnetIfTraps configuration object.
NTF stnConfigAuditPppoeIfFailure	1.3.6.1.4.1.3551.2.100.0.35			A stnConfigAuditPppoeIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPPOE interface after a failover. The generation of this trap can be controlled by the CfgAuditPppoeIfTraps configuration object.
NTF stnConfigAuditPppIfFailure	1.3.6.1.4.1.3551.2.100.0.36			A stnConfigAuditPppIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPP interface after a failover. The generation of this trap can be controlled by the CfgAuditPppIfTraps configuration object.

DisplayString (3)
STR stnRouterName	1.3.6.1.4.1.3551.2.7.1.1.1.7	DisplayString	read-only	The name of this router.
STR stnRouterServiceName	1.3.6.1.4.1.3551.2.7.1.1.1.16	DisplayString	read-only	The service to which this router belongs.
STR stnSubnetInterfaceServiceName	1.3.6.1.4.1.3551.2.7.1.2.1.12	DisplayString	read-only	The service to which this interface belongs.
INTEGER (7)
INT stnPppoeLinkType	1.3.6.1.4.1.3551.2.7.1.3.1.7	INTEGER	read-only	Indicates the type of link the PPPoE interface is configured over.
INT stnRouterDefaultPolicyAction	1.3.6.1.4.1.3551.2.7.1.1.1.18	INTEGER	read-only	Action to take when a packet does not match any policies.
INT stnRouterEnabled	1.3.6.1.4.1.3551.2.7.1.1.1.6	INTEGER	read-only	The variable to indicate if this router is enabled.
INT stnRouterReassignOnFault	1.3.6.1.4.1.3551.2.7.1.1.1.15	INTEGER	read-only	The variable to indicate if this router should be reassigned if the module where to fail.
INT stnRouterType	1.3.6.1.4.1.3551.2.7.1.1.1.2	INTEGER	read-only	The router type.
INT stnSubnetInterfaceEnabled	1.3.6.1.4.1.3551.2.7.1.2.1.2	INTEGER	read-only	Enable or disable the sub-network interface.
INT stnSubnetInterfaceLinkType	1.3.6.1.4.1.3551.2.7.1.2.1.9	INTEGER	read-only	Indicates the type of link the subnet interface is configured over.
Integer32 (19)
I32 stnPppIndex	1.3.6.1.4.1.3551.2.7.1.4.1.1	Integer32	read-only	A sequence number that identifies a PPP interface entry in the table.
I32 stnPppoeIndex	1.3.6.1.4.1.3551.2.7.1.3.1.1	Integer32	read-only	A sequence number that identifies a PPPOE interface entry in the table.
I32 stnPppoeLinkInstance	1.3.6.1.4.1.3551.2.7.1.3.1.8	Integer32	read-only	The instance of the configuration record for the link the PPPoE interface is configured over.
I32 stnPppoeRouterIndex	1.3.6.1.4.1.3551.2.7.1.3.1.6	Integer32	read-only	The router this PPPOE interface is associated with.
I32 stnPppoeVclid	1.3.6.1.4.1.3551.2.7.1.3.1.4	Integer32	read-only	The vcl ID associated with this PPPOE interface.
I32 stnPppRouterIndex	1.3.6.1.4.1.3551.2.7.1.4.1.6	Integer32	read-only	The router this PPP interface is associated with.
I32 stnPppVclid	1.3.6.1.4.1.3551.2.7.1.4.1.4	Integer32	read-only	The vcl ID associated with this PPP interface.
I32 stnRouterActiveCpu	1.3.6.1.4.1.3551.2.7.1.1.1.10	Integer32	read-only	The CPU to which this router is currently assigned.
I32 stnRouterActiveSlot	1.3.6.1.4.1.3551.2.7.1.1.1.9	Integer32	read-only	The slot/module to which this router is currently assigned.
I32 stnRouterConfiguredCpu	1.3.6.1.4.1.3551.2.7.1.1.1.12	Integer32	read-only	The configured CPU for this router.
I32 stnRouterConfiguredSlot	1.3.6.1.4.1.3551.2.7.1.1.1.11	Integer32	read-only	The configured slot/module for this router.
I32 stnRouterEngineID	1.3.6.1.4.1.3551.2.7.1.1.1.4	Integer32	read-only	The engine to which this router is currently assigned.
I32 stnRouterIndex	1.3.6.1.4.1.3551.2.7.1.1.1.1	Integer32	read-only	A sequence number that identifies a router entry in the table.
I32 stnRouterServiceDomain	1.3.6.1.4.1.3551.2.7.1.1.1.17	Integer32	read-only	The service domain to which this router belongs.
I32 stnRouterStandbyCpu	1.3.6.1.4.1.3551.2.7.1.1.1.14	Integer32	read-only	The standby CPU for this router.
I32 stnRouterStandbySlot	1.3.6.1.4.1.3551.2.7.1.1.1.13	Integer32	read-only	The standby slot/module for this router.
I32 stnSubnetInterfaceLinkInstance	1.3.6.1.4.1.3551.2.7.1.2.1.10	Integer32	read-only	The instance of the configuration record for the link the subnet interface is configured over.
I32 stnSubnetInterfaceRouterIndex	1.3.6.1.4.1.3551.2.7.1.2.1.8	Integer32	read-only	The router this sub-network interface is associated with.
I32 stnSubnetInterfaceVclid	1.3.6.1.4.1.3551.2.7.1.2.1.5	Integer32	read-only	The vcl ID associated with this sub-network interface.
InterfaceConnectionType (3)
NUM stnPppoeType	1.3.6.1.4.1.3551.2.7.1.3.1.2	InterfaceConnectionType	read-only	The interface type.
NUM stnPppType	1.3.6.1.4.1.3551.2.7.1.4.1.2	InterfaceConnectionType	read-only	The interface type.
NUM stnSubnetInterfaceType	1.3.6.1.4.1.3551.2.7.1.2.1.6	InterfaceConnectionType	read-only	The interface type.
InterfaceIndex (2)
NUM stnPppIfIndex	1.3.6.1.4.1.3551.2.7.1.4.1.5	InterfaceIndex	read-only	The ifindex.
NUM stnPppoeIfIndex	1.3.6.1.4.1.3551.2.7.1.3.1.5	InterfaceIndex	read-only	The ifindex.
IpAddress (4)
IP stnRouterHomeIpAddress	1.3.6.1.4.1.3551.2.7.1.1.1.5	IpAddress	read-only	The Home IP address of this router.
IP stnSubnetInterfaceAddress	1.3.6.1.4.1.3551.2.7.1.2.1.3	IpAddress	read-only	The IP address of this interface.
IP stnSubnetInterfaceForcedNextHop	1.3.6.1.4.1.3551.2.7.1.2.1.11	IpAddress	read-only	The IP address of the next hop router that all IP traffic received on this interface will be sent to
IP stnSubnetInterfaceMask	1.3.6.1.4.1.3551.2.7.1.2.1.4	IpAddress	read-only	The sub-network mask of this interface.
OperationState (4)
OPE stnPppoeState	1.3.6.1.4.1.3551.2.7.1.3.1.3	OperationState	read-only	The operational state of the PPPOE interface.
OPE stnPppState	1.3.6.1.4.1.3551.2.7.1.4.1.3	OperationState	read-only	The operational state or the PPP interface.
OPE stnRouterState	1.3.6.1.4.1.3551.2.7.1.1.1.3	OperationState	read-only	The operational state of the router.
OPE stnSubnetInterfaceState	1.3.6.1.4.1.3551.2.7.1.2.1.7	OperationState	read-only	The operational state of the sub-network interface.
TimeTicks (1)
TIK stnRouterUpTime	1.3.6.1.4.1.3551.2.7.1.1.1.8	TimeTicks	read-only	The time (in hundredths of a second) since the router was last re-initialized.
Unsigned32 (1)
U32 stnSubnetInterfaceIndex	1.3.6.1.4.1.3551.2.7.1.2.1.1	Unsigned32	read-only	A sequence number that identifies a sub-network interface entry in the table.
No type (25)
NTF stnConfigAuditPppIfFailure	1.3.6.1.4.1.3551.2.100.0.36			A stnConfigAuditPppIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPP interface after a failover. The generation of this trap can be controlled by the CfgAuditPppIfTraps configuration object.
NTF stnConfigAuditPppoeIfFailure	1.3.6.1.4.1.3551.2.100.0.35			A stnConfigAuditPppoeIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured PPPOE interface after a failover. The generation of this trap can be controlled by the CfgAuditPppoeIfTraps configuration object.
NTF stnConfigAuditRouterFailure	1.3.6.1.4.1.3551.2.100.0.33			A stnConfigAuditRouterFailure trap signifies that the agent entity has detected an inconsistency between an active and configured routers after a failover. The generation of this trap can be controlled by the CfgAuditRouterTraps configuration object.
NTF stnConfigAuditSubnetIfFailure	1.3.6.1.4.1.3551.2.100.0.34			A stnConfigAuditSubnetIfFailure trap signifies that agent entity has detected an inconsistency between an active and configured subnet interface after a failover. The generation of this trap can be controlled by the CfgAuditSubnetIfTraps configuration object.
stnPppEntry	1.3.6.1.4.1.3551.2.7.1.4.1		not-accessible	Entry contains information about a particular session.
stnPppoeEntry	1.3.6.1.4.1.3551.2.7.1.3.1		not-accessible	Entry contains information about a particular PPPOE interface.
stnPppoeTable	1.3.6.1.4.1.3551.2.7.1.3		not-accessible	A list of PPPOE interface entries.
stnPppTable	1.3.6.1.4.1.3551.2.7.1.4		not-accessible	A list of PPP interface entries.
stnRouter	1.3.6.1.4.1.3551.2.7			This MIB module describes managed objects of Spring Tide Networks virtual routers plus associated IP, PPP, and PPPOE interfaces.
stnRouterAtmVpn	1.3.6.1.4.1.3551.2.7.1.7
NTF stnRouterDown	1.3.6.1.4.1.3551.2.100.0.27			A stnRouterDown trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterDownTraps configuration object.
stnRouterEntry	1.3.6.1.4.1.3551.2.7.1.1.1		not-accessible	Entry contains information about a particular router.
stnRouterMibConformance	1.3.6.1.4.1.3551.2.7.2
stnRouterNAT	1.3.6.1.4.1.3551.2.7.1.5
stnRouterObjects	1.3.6.1.4.1.3551.2.7.1
NTF stnRouterReassigned	1.3.6.1.4.1.3551.2.100.0.28			A stnRouterReassigned trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the the assigned(1) state for one of its routers. The generation of this trap can be controlled by the RouterReassignedTraps configuration object.
NTF stnRouterReassignFailure	1.3.6.1.4.1.3551.2.100.0.29			A stnRouterReassignFailure trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its routers. The generation of this trap can be controlled by the RouterReassignFailureTraps configuration object.
stnRouterTable	1.3.6.1.4.1.3551.2.7.1.1		not-accessible	A list of router entries.
NTF stnRouterUp	1.3.6.1.4.1.3551.2.100.0.26			A stnRouterUp trap signifies that the agent entity has detected that the stnRouterState object in the STN-ROUTER-MIB has transitioned to the assigned(4) state for one of its routers. The generation of this trap can be controlled by the RouterUpTraps configuration object.
stnRouterVEI	1.3.6.1.4.1.3551.2.7.1.6
stnRouterVimuxMpls	1.3.6.1.4.1.3551.2.7.1.8
stnRouterVTI	1.3.6.1.4.1.3551.2.7.1.9
NTF stnSubnetIfAssignFailure	1.3.6.1.4.1.3551.2.100.0.30			A stnSubnetIfAssignFailure trap signifies that the agent entity has detected that the stnSubnetInterfaceState object in the STN-ROUTER-MIB has transitioned to the failedassign(7) or error(8) state for one of its interfaces. The generation of this trap can be controlled by the stnEnableSubnetInterfaceTraps configuration object.
stnSubnetInterfaceEntry	1.3.6.1.4.1.3551.2.7.1.2.1		not-accessible	Entry contains information about a particular sub-network interface.
stnSubnetInterfaceTable	1.3.6.1.4.1.3551.2.7.1.2		not-accessible	A list of sub-network interface entries.

RFC description

Stonesoft enterprise router MIB for network appliance and firewall management.

Start monitoring Spring Tide Networks (Lucent) IP Service Switch 5000 virtual-router platform (discontinued) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download STN-ROUTER-MIB

This MIB depends on

Related MIBs

What Is STN-ROUTER-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description