Nortel-Magellan-Passport-AtmUniMIB

All MIBs › Nortel-Magellan-Passport-AtmUniMIB

Category: ATM

Description: Manages Nortel Magellan Passport ATM UNI signaling, address registration, and connection admission.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-AtmUniMIB?

Nortel-Magellan-Passport-AtmUniMIB is a Nortel Magellan Passport switch MIB governing ATM User-Network Interface (UNI) signaling, address registration, and connection admission on this multiservice WAN switching platform. It exposes tables for UNI interface provisioning and status, including UNI version, side (user/network), soft PVC retry behavior, and an ILMI (Interim Local Management Interface) sub-branch used for UNI address/parameter negotiation. Its monitoring focus is on the operational and configuration status of ATM UNI links: verifying atmIfUniRowStatus shows an interface is active, confirming atmIfUniVersion and atmIfUniSide match the expected signaling configuration, and watching soft-PVC retry activity as an indicator of connection setup problems on the interface. Like its sibling AtmTrunksMIB, it follows the Passport platform's common RowStatus/StorageType/ComponentName conventions for provisioned objects. It is deployed on Nortel Magellan Passport nodes providing ATM UNI access for carrier or enterprise ATM services. Engineers can download the Nortel-Magellan-Passport-AtmUniMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-AtmUniMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport multiservice switch

Monitoring Examples

An operator would check atmIfUniRowStatusTable/atmIfUniRowStatusEntry's atmIfUniRowStatus per atmIfUniIndex to confirm a UNI interface is provisioned and active rather than stuck in a notReady state. Reviewing atmIfUniProvTable/atmIfUniProvEntry fields such as atmIfUniVersion, atmIfUniSide, and atmIfUniSoftPvcRetryPeriod helps diagnose why a soft PVC on that interface repeatedly fails to establish, since a mismatched UNI version or side setting is a common misconfiguration. The atmIfUniIlmi branch would be consulted to check ILMI-based address registration status for the interface.

What Can Be Monitored

ATM UNI interface row/operational status
UNI version and side
soft PVC retry period
ILMI registration status

Imported Objects

From Nortel-Magellan-Passport-AtmCoreMIB

atmIf	OBJECT-IDENTITY
atmIfIndex	OBJECT-TYPE
atmIfVpt	OBJECT-IDENTITY
atmIfVptIndex	OBJECT-TYPE

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

AsciiString
AsciiStringIndex
Hex
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmIfUni	1.3.6.1.4.1.562.2.4.1.114.6
atmIfUniRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.1		not-accessible	This entry controls the addition and deletion of atmIfUni components.
atmIfUniRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.1.1		not-accessible	A single entry in the table represents a single atmIfUni component.
ROW atmIfUniRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfUni components. These components can be added and deleted.
STR atmIfUniComponentName	1.3.6.1.4.1.562.2.4.1.114.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniStorageType	1.3.6.1.4.1.562.2.4.1.114.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUni tables.
NON atmIfUniIndex	1.3.6.1.4.1.562.2.4.1.114.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUni tables.
atmIfUniIlmi	1.3.6.1.4.1.562.2.4.1.114.6.2
atmIfUniIlmiRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.2.1		not-accessible	This entry controls the addition and deletion of atmIfUniIlmi components.
atmIfUniIlmiRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.1.1		not-accessible	A single entry in the table represents a single atmIfUniIlmi component.
ROW atmIfUniIlmiRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfUniIlmi components. These components cannot be added nor deleted.
STR atmIfUniIlmiComponentName	1.3.6.1.4.1.562.2.4.1.114.6.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniIlmiStorageType	1.3.6.1.4.1.562.2.4.1.114.6.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniIlmi tables.
NON atmIfUniIlmiIndex	1.3.6.1.4.1.562.2.4.1.114.6.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUniIlmi tables.
atmIfUniIlmiStateTable	1.3.6.1.4.1.562.2.4.1.114.6.2.10		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfUniIlmiStateEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.10.1		not-accessible	An entry in the atmIfUniIlmiStateTable.
INT atmIfUniIlmiAdminState	1.3.6.1.4.1.562.2.4.1.114.6.2.10.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfUniIlmiOperationalState	1.3.6.1.4.1.562.2.4.1.114.6.2.10.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfUniIlmiUsageState	1.3.6.1.4.1.562.2.4.1.114.6.2.10.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfUniIlmiProvTable	1.3.6.1.4.1.562.2.4.1.114.6.2.11		not-accessible	This attribute group contains the provisionable attributes for the Ilmi component.
atmIfUniIlmiProvEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.11.1		not-accessible	An entry in the atmIfUniIlmiProvTable.
U32 atmIfUniIlmiVci	1.3.6.1.4.1.562.2.4.1.114.6.2.11.1.1	Unsigned32	read-write	This attribute identifies the ILMI channel number.
INT atmIfUniIlmiOperatingMode	1.3.6.1.4.1.562.2.4.1.114.6.2.11.1.2	INTEGER	read-write	This attribute is used to enable/disable the ILMI protocol. addressRegEnabled indicates that the ILMI address registration protocol is enabled. addressRegDisabled indicates that the ILMI address registration protocol is disabled. ilmiDisabled indicates that all of ILMI is disabled.
atmIfUniIlmiStatsTable	1.3.6.1.4.1.562.2.4.1.114.6.2.12		not-accessible	This attribute group contains the statistics for the AtmIlmi component.
atmIfUniIlmiStatsEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.12.1		not-accessible	An entry in the atmIfUniIlmiStatsTable.
C32 atmIfUniIlmiTxPdus	1.3.6.1.4.1.562.2.4.1.114.6.2.12.1.1	Counter32	read-only	This attribute counts the number of transmitted ILMI PDUs. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniIlmiRxPdus	1.3.6.1.4.1.562.2.4.1.114.6.2.12.1.2	Counter32	read-only	This attribute counts the total number of received ILMI PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniIlmiRxBadPdusDiscarded	1.3.6.1.4.1.562.2.4.1.114.6.2.12.1.3	Counter32	read-only	This attribute counts the number of received ILMI PDUs that were discarded due to invalid SNMP format. The counter wraps to 0 when the maximum value is exceeded.
atmIfUniIlmiPrefixToRegisterTable	1.3.6.1.4.1.562.2.4.1.114.6.2.287		not-accessible	This attribute is a list of zero or more addresses. If the side attribute in the Uni component is set to user, then this attribute must be empty; if the side attribute is set to network, then this attribute is a list of prefixes.This attribute represents a list of prefix addresses (26 digits) that are sent to the user side. If no prefixes are entered, then the nodeAddress attribute in the AtmCallRouter component is used for address registration.
atmIfUniIlmiPrefixToRegisterEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.287.1		not-accessible	An entry in the atmIfUniIlmiPrefixToRegisterTable.
STR atmIfUniIlmiPrefixToRegisterValue	1.3.6.1.4.1.562.2.4.1.114.6.2.287.1.1	AsciiString	read-write	This variable represents both the value and the index for the atmIfUniIlmiPrefixToRegisterTable.
ROW atmIfUniIlmiPrefixToRegisterRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.2.287.1.2	RowStatus	write-only	This variable is used to control the addition and deletion of individual values of the atmIfUniIlmiPrefixToRegisterTable.
atmIfUniIlmiEsiToRegisterTable	1.3.6.1.4.1.562.2.4.1.114.6.2.288		not-accessible	This attribute is a list of zero or more addresses. If the side attribute in the Uni component is set to network, then this attribute must be an empty list; if the side attribute is set to user, then this attribute is a list of end system indicators (ESI) addresses (12 hex digits) that are used to compose addresses to register with the network side.
atmIfUniIlmiEsiToRegisterEntry	1.3.6.1.4.1.562.2.4.1.114.6.2.288.1		not-accessible	An entry in the atmIfUniIlmiEsiToRegisterTable.
STR atmIfUniIlmiEsiToRegisterValue	1.3.6.1.4.1.562.2.4.1.114.6.2.288.1.1	AsciiString	read-write	This variable represents both the value and the index for the atmIfUniIlmiEsiToRegisterTable.
ROW atmIfUniIlmiEsiToRegisterRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.2.288.1.2	RowStatus	write-only	This variable is used to control the addition and deletion of individual values of the atmIfUniIlmiEsiToRegisterTable.
atmIfUniSig	1.3.6.1.4.1.562.2.4.1.114.6.3
atmIfUniSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.3.1		not-accessible	This entry controls the addition and deletion of atmIfUniSig components.
atmIfUniSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.1.1		not-accessible	A single entry in the table represents a single atmIfUniSig component.
ROW atmIfUniSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfUniSig components. These components cannot be added nor deleted.
STR atmIfUniSigComponentName	1.3.6.1.4.1.562.2.4.1.114.6.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniSigStorageType	1.3.6.1.4.1.562.2.4.1.114.6.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniSig tables.
NON atmIfUniSigIndex	1.3.6.1.4.1.562.2.4.1.114.6.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUniSig tables.
atmIfUniSigVcd	1.3.6.1.4.1.562.2.4.1.114.6.3.2
atmIfUniSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfUniSigVcd components.
atmIfUniSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfUniSigVcd component.
ROW atmIfUniSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfUniSigVcd components. These components can be added and deleted.
STR atmIfUniSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniSigVcd tables.
NON atmIfUniSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.6.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUniSigVcd tables.
atmIfUniSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfUniSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1		not-accessible	An entry in the atmIfUniSigVcdProvTable.
INT atmIfUniSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfUniSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfUniSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfUniSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfUniSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfUniSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.6.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfUniSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.6.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfUniSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.2.387.1		not-accessible	An entry in the atmIfUniSigVcdTdpTable.
I32 atmIfUniSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.6.3.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfUniSigVcdTdpTable specific index for the atmIfUniSigVcdTdpTable.
U32 atmIfUniSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.6.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfUniSigVcdTdpTable.
atmIfUniSigProvTable	1.3.6.1.4.1.562.2.4.1.114.6.3.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfUniSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.10.1		not-accessible	An entry in the atmIfUniSigProvTable.
U32 atmIfUniSigVci	1.3.6.1.4.1.562.2.4.1.114.6.3.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfUniSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.6.3.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfUniSigStateTable	1.3.6.1.4.1.562.2.4.1.114.6.3.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfUniSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.11.1		not-accessible	An entry in the atmIfUniSigStateTable.
INT atmIfUniSigAdminState	1.3.6.1.4.1.562.2.4.1.114.6.3.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfUniSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.6.3.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfUniSigUsageState	1.3.6.1.4.1.562.2.4.1.114.6.3.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfUniSigOperTable	1.3.6.1.4.1.562.2.4.1.114.6.3.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfUniSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.12.1		not-accessible	An entry in the atmIfUniSigOperTable.
U32 atmIfUniSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.6.3.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfUniSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.6.3.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfUniSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.6.3.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfUniSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.6.3.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfUniSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.6.3.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfUniSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1		not-accessible	An entry in the atmIfUniSigStatsTable.
C32 atmIfUniSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfUniSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfUniSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfUniSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfUniSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfUniSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfUniSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfUniSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.6.3.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfUniAddr	1.3.6.1.4.1.562.2.4.1.114.6.4
atmIfUniAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.4.1		not-accessible	This entry controls the addition and deletion of atmIfUniAddr components.
atmIfUniAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1		not-accessible	A single entry in the table represents a single atmIfUniAddr component.
ROW atmIfUniAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfUniAddr components. These components can be added and deleted.
STR atmIfUniAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniAddr tables.
STR atmIfUniAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfUniAddr tables.
INT atmIfUniAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.6.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfUniAddr tables.
atmIfUniAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.6.4.2
atmIfUniAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1		not-accessible	This entry controls the addition and deletion of atmIfUniAddrTermSP components.
atmIfUniAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1.1		not-accessible	A single entry in the table represents a single atmIfUniAddrTermSP component.
ROW atmIfUniAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfUniAddrTermSP components. These components can be added and deleted.
STR atmIfUniAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniAddrTermSP tables.
NON atmIfUniAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.6.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUniAddrTermSP tables.
atmIfUniAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.6.4.3
atmIfUniAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1		not-accessible	This entry controls the addition and deletion of atmIfUniAddrPnniInfo components.
atmIfUniAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1.1		not-accessible	A single entry in the table represents a single atmIfUniAddrPnniInfo component.
ROW atmIfUniAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfUniAddrPnniInfo components. These components can be added and deleted.
STR atmIfUniAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfUniAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfUniAddrPnniInfo tables.
NON atmIfUniAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.6.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfUniAddrPnniInfo tables.
atmIfUniAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.6.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfUniAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.6.4.3.10.1		not-accessible	An entry in the atmIfUniAddrPnniInfoProvTable.
INT atmIfUniAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.6.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfUniAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.6.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfUniAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.6.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfUniAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.6.4.10.1		not-accessible	An entry in the atmIfUniAddrOperTable.
INT atmIfUniAddrScope	1.3.6.1.4.1.562.2.4.1.114.6.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfUniAddrReachability	1.3.6.1.4.1.562.2.4.1.114.6.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfUniProvTable	1.3.6.1.4.1.562.2.4.1.114.6.10		not-accessible	This group contains the provisionable attributes for the Uni component.
atmIfUniProvEntry	1.3.6.1.4.1.562.2.4.1.114.6.10.1		not-accessible	An entry in the atmIfUniProvTable.
INT atmIfUniVersion	1.3.6.1.4.1.562.2.4.1.114.6.10.1.1	INTEGER	read-write	This attribute specifies which specification the UNI complies with. The options are ATM FORUM 3.0 or ATM FORUM 3.1. If this attribute is changed then all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT atmIfUniSide	1.3.6.1.4.1.562.2.4.1.114.6.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 atmIfUniSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.6.10.1.3	Unsigned32	read-write	This attribute represents the time in seconds to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfUniSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.6.10.1.4	Unsigned32	read-write	This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfUniSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.6.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfUniOperTable	1.3.6.1.4.1.562.2.4.1.114.6.11		not-accessible	This attribute group contains the operational attributes for the Uni component.
atmIfUniOperEntry	1.3.6.1.4.1.562.2.4.1.114.6.11.1		not-accessible	An entry in the atmIfUniOperTable.
STR atmIfUniMacAddress	1.3.6.1.4.1.562.2.4.1.114.6.11.1.1	AsciiString	read-only	This attribute indicates the MAC address of the port, which is used for address registration of the user side as the default ESI.
atmIfUniAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.6.12		not-accessible	This group contains the provisionable attributes for accounting.
atmIfUniAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.6.12.1		not-accessible	An entry in the atmIfUniAcctOptTable.
OCT atmIfUniAccountCollection	1.3.6.1.4.1.562.2.4.1.114.6.12.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfUniAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.6.12.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfUniAccountClass	1.3.6.1.4.1.562.2.4.1.114.6.12.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfUniServiceExchange	1.3.6.1.4.1.562.2.4.1.114.6.12.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfVptUni	1.3.6.1.4.1.562.2.4.1.114.9.8
atmIfVptUniRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.1		not-accessible	This entry controls the addition and deletion of atmIfVptUni components.
atmIfVptUniRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.1.1		not-accessible	A single entry in the table represents a single atmIfVptUni component.
ROW atmIfVptUniRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptUni components. These components can be added and deleted.
STR atmIfVptUniComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUni tables.
NON atmIfVptUniIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptUni tables.
atmIfVptUniSig	1.3.6.1.4.1.562.2.4.1.114.9.8.2
atmIfVptUniSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptUniSig components.
atmIfVptUniSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptUniSig component.
ROW atmIfVptUniSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfVptUniSig components. These components cannot be added nor deleted.
STR atmIfVptUniSigComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniSigStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUniSig tables.
NON atmIfVptUniSigIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptUniSig tables.
atmIfVptUniSigVcd	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2
atmIfVptUniSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptUniSigVcd components.
atmIfVptUniSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptUniSigVcd component.
ROW atmIfVptUniSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptUniSigVcd components. These components can be added and deleted.
STR atmIfVptUniSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUniSigVcd tables.
NON atmIfVptUniSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptUniSigVcd tables.
atmIfVptUniSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfVptUniSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1		not-accessible	An entry in the atmIfVptUniSigVcdProvTable.
INT atmIfVptUniSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfVptUniSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfVptUniSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfVptUniSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfVptUniSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfVptUniSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfVptUniSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfVptUniSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.387.1		not-accessible	An entry in the atmIfVptUniSigVcdTdpTable.
I32 atmIfVptUniSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfVptUniSigVcdTdpTable specific index for the atmIfVptUniSigVcdTdpTable.
U32 atmIfVptUniSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.9.8.2.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfVptUniSigVcdTdpTable.
atmIfVptUniSigProvTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfVptUniSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.10.1		not-accessible	An entry in the atmIfVptUniSigProvTable.
U32 atmIfVptUniSigVci	1.3.6.1.4.1.562.2.4.1.114.9.8.2.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfVptUniSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.9.8.2.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfVptUniSigStateTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfVptUniSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.11.1		not-accessible	An entry in the atmIfVptUniSigStateTable.
INT atmIfVptUniSigAdminState	1.3.6.1.4.1.562.2.4.1.114.9.8.2.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfVptUniSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.9.8.2.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfVptUniSigUsageState	1.3.6.1.4.1.562.2.4.1.114.9.8.2.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfVptUniSigOperTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfVptUniSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12.1		not-accessible	An entry in the atmIfVptUniSigOperTable.
U32 atmIfVptUniSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptUniSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfVptUniSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptUniSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.8.2.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfVptUniSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfVptUniSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1		not-accessible	An entry in the atmIfVptUniSigStatsTable.
C32 atmIfVptUniSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfVptUniSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfVptUniSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptUniSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptUniSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptUniSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptUniSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfVptUniSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfVptUniSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptUniSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptUniSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.8.2.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfVptUniAddr	1.3.6.1.4.1.562.2.4.1.114.9.8.3
atmIfVptUniAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptUniAddr components.
atmIfVptUniAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptUniAddr component.
ROW atmIfVptUniAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptUniAddr components. These components can be added and deleted.
STR atmIfVptUniAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUniAddr tables.
STR atmIfVptUniAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfVptUniAddr tables.
INT atmIfVptUniAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.3.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfVptUniAddr tables.
atmIfVptUniAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2
atmIfVptUniAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptUniAddrTermSP components.
atmIfVptUniAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptUniAddrTermSP component.
ROW atmIfVptUniAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptUniAddrTermSP components. These components can be added and deleted.
STR atmIfVptUniAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUniAddrTermSP tables.
NON atmIfVptUniAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptUniAddrTermSP tables.
atmIfVptUniAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3
atmIfVptUniAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptUniAddrPnniInfo components.
atmIfVptUniAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptUniAddrPnniInfo component.
ROW atmIfVptUniAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptUniAddrPnniInfo components. These components can be added and deleted.
STR atmIfVptUniAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptUniAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptUniAddrPnniInfo tables.
NON atmIfVptUniAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptUniAddrPnniInfo tables.
atmIfVptUniAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfVptUniAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.10.1		not-accessible	An entry in the atmIfVptUniAddrPnniInfoProvTable.
INT atmIfVptUniAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfVptUniAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.9.8.3.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptUniAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.9.8.3.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfVptUniAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.3.10.1		not-accessible	An entry in the atmIfVptUniAddrOperTable.
INT atmIfVptUniAddrScope	1.3.6.1.4.1.562.2.4.1.114.9.8.3.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfVptUniAddrReachability	1.3.6.1.4.1.562.2.4.1.114.9.8.3.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptUniProvTable	1.3.6.1.4.1.562.2.4.1.114.9.8.10		not-accessible	This group contains the provisionable attributes for the Uni component.
atmIfVptUniProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1		not-accessible	An entry in the atmIfVptUniProvTable.
INT atmIfVptUniVersion	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1.1	INTEGER	read-write	This attribute specifies which specification the UNI complies with. The options are ATM FORUM 3.0 or ATM FORUM 3.1. If this attribute is changed then all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT atmIfVptUniSide	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 atmIfVptUniSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1.3	Unsigned32	read-write	This attribute represents the time in seconds to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfVptUniSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1.4	Unsigned32	read-write	This attribute represents the time in seconds to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfVptUniSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.9.8.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfVptUniAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.9.8.11		not-accessible	This group contains the provisionable attributes for accounting.
atmIfVptUniAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.11.1		not-accessible	An entry in the atmIfVptUniAcctOptTable.
OCT atmIfVptUniAccountCollection	1.3.6.1.4.1.562.2.4.1.114.9.8.11.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfVptUniAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.9.8.11.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfVptUniAccountClass	1.3.6.1.4.1.562.2.4.1.114.9.8.11.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfVptUniServiceExchange	1.3.6.1.4.1.562.2.4.1.114.9.8.11.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfVptUniVProvTable	1.3.6.1.4.1.562.2.4.1.114.9.8.12		not-accessible	This group contains the provisionable attributes for the Uni component which are specific to virtual UNI interfaces.
atmIfVptUniVProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.8.12.1		not-accessible	An entry in the atmIfVptUniVProvTable.
U32 atmIfVptUniVpci	1.3.6.1.4.1.562.2.4.1.114.9.8.12.1.1	Unsigned32	read-write	This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual UNI must have the same value for switched connections to be set up across the interface.
atmUniMIB	1.3.6.1.4.1.562.2.4.2.69
atmUniGroup	1.3.6.1.4.1.562.2.4.2.69.1
atmUniGroupBE	1.3.6.1.4.1.562.2.4.2.69.1.5
atmUniGroupBE00	1.3.6.1.4.1.562.2.4.2.69.1.5.1
atmUniGroupBE00A	1.3.6.1.4.1.562.2.4.2.69.1.5.1.2
atmUniCapabilities	1.3.6.1.4.1.562.2.4.2.69.3
atmUniCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.69.3.5
atmUniCapabilitiesBE00	1.3.6.1.4.1.562.2.4.2.69.3.5.1
atmUniCapabilitiesBE00A	1.3.6.1.4.1.562.2.4.2.69.3.5.1.2

RFC description

Manages ATM UNI (User Network Interface) components on Nortel Magellan Passport network equipment.

Start monitoring Nortel Magellan Passport multiservice switch (ATM UNI signaling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-AtmUniMIB

What Is Nortel-Magellan-Passport-AtmUniMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description