STN-ATM-VPN-MIB

All MIBs › STN-ATM-VPN-MIB

Organization: Spring Tide Networks

Last Updated: 2000-08-08

Category: ATM, Spring Tide Networks

Description: Manages Spring Tide Networks ATM-based VPN circuit provisioning and associated service parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is STN-ATM-VPN-MIB?

STN-ATM-VPN-MIB is a Spring Tide Networks proprietary MIB describing managed objects for ATM-based VPN interfaces on Spring Tide's carrier-class multiservice switching platforms. It is expected to expose configuration and status objects for provisioned ATM VPN circuits/interfaces, including their service parameters, placing it in the configuration and interface-status category of MIBs. Given the ATM-VPN focus, its monitoring relevance is primarily around circuit/interface operational status and service-parameter configuration rather than chassis hardware sensors, letting operators confirm that provisioned VPN circuits are up and correctly parameterized. It likely depends on standard ATM-MIB and IF-MIB conventions for interface indexing, since ATM VPN interfaces are typically layered over standard ATM interface objects. It was deployed on Spring Tide Networks multiservice switches used by service providers offering ATM-based VPN transport. Engineers can download the STN-ATM-VPN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in STN-ATM-VPN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Spring Tide Networks multiservice ATM switch

Monitoring Examples

No concrete object or table names were supplied for this module, so a grounded polling scenario cannot be given; in general, an ATM-VPN MIB of this kind would let an operator poll per-circuit configuration and operational-status objects to confirm provisioned VPN interfaces are active and correctly parameterized for the intended service level.

Imported Objects

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From SPRING-TIDE-NETWORKS-SMI

stnNotification

OBJECT-IDENTITY

From STN-ROUTER-MIB

stnRouterAtmVpn

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using stnAtmVpnTrunkInVpnIdIfaceInvalid OID:

Select a Spring Tide Networks (Lucent) multiservice ATM switch (ATM VPN interface config) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type stnAtmVpnTrunkInVpnIdIfaceInvalid into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number packets received with a Vpn-Id that was known, but the entry in the FIB refered to an invalid or non-existant interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
stnAtmVpn	1.3.6.1.4.1.3551.2.7.1.7.1			This MIB module describes managed objects of Spring Tide Networks ATM VPN Interfaces.
stnAtmVpnTrunkObjects	1.3.6.1.4.1.3551.2.7.1.7.1.1
stnAtmVpnTrunkTable	1.3.6.1.4.1.3551.2.7.1.7.1.1.1		not-accessible	A list of ATM VPN Trunk entries.
stnAtmVpnTrunkEntry	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1		not-accessible	Entry contains information about a particular ATM VPN Trunk.
NUM stnAtmVpnTrunkIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.1	InterfaceIndex	read-only	The ifIndex of the ATM VPN Trunk Interface.
I32 stnAtmVpnTrunkViId	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.2	Integer32	read-only	The instance of the configuration record corresponding to this ATM VPN Trunk.
STR stnAtmVpnTrunkName	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.3	DisplayString	read-only	The name configured for this ATM VPN Trunk.
INT stnAtmVpnTrunkState	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.4	INTEGER	read-only	The current operational state of the ATM VPN Trunk.
NUM stnAtmVpnTrunkLowerIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.5	InterfaceIndex	read-only	The ifIndex of the Interface below the ATM VPN Trunk Interface.
I32 stnAtmVpnTrunkVpnPaths	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.6	Integer32	read-only	The number of VPN Paths that this ATM VPN Trunk has in its forwarding table.
C64 stnAtmVpnTrunkInUnknownVpnId	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.7	Counter64	read-only	The number packets received with a Vpn-Id that was not present it the ATM VPN Trunk's forwarding table.
C64 stnAtmVpnTrunkInVpnIdIfaceInvalidEx	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.8	Counter64	read-only	The number packets received with a Vpn-Id that was known, but the entry in the FIB refered to an invalid or non-existant interface. This can indicate an invalid configuration.
C64 stnAtmVpnTrunkOutUnknownVpnId	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.9	Counter64	read-only	The number packets passed to this trunk from another ATM VPN Trunk or Link with a Vpn-Id that was not present it the ATM VPN Trunk's forwarding table.
C64 stnAtmVpnTrunkOutVpnIdIfaceInvalid	1.3.6.1.4.1.3551.2.7.1.7.1.1.1.1.10	Counter64	read-only	The number packets passed to this trunk from another ATM VPN Trunk or Link when there was no suitable interface below the ATM VPN Trunk.
stnAtmVpnTrunkPathTable	1.3.6.1.4.1.3551.2.7.1.7.1.1.2		not-accessible	A list of the ATM VPN Paths known to a ATM VPN Trunk.
stnAtmVpnTrunkPathEntry	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1		not-accessible	Entry contains information about a particular remote MAC learned on a VEI VcLink.
NUM stnAtmVpnTrunkPathTrunkIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.1	InterfaceIndex	read-only	The IfIndex of the ATM VPN Trunk Interface which owns the VPN Path entry.
I32 stnAtmVpnTrunkPathVpnOUI	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.2	Integer32	read-only	The VPN OUI for which packets this VPN Path pertains to.
I32 stnAtmVpnTrunkPathVpnIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.3	Integer32	read-only	The VPN Index for which packets this VPN Path pertains to.
I32 stnAtmVpnTrunkPathVpnSubIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.4	Integer32	read-only	The VPN SubIndex for which packets this VPN Path pertains to.
INT stnAtmVpnTrunkPathType	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.5	INTEGER	read-only	Indicates the type of the VPN Path database entry. Learned indicates that the entry was dynamically learned from link/trunk configuration or other dynamic means. Static indicates that the entry was configured explicitly using a VirtualInterfaceInfo Entry.
INT stnAtmVpnTrunkPathNextIfType	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.6	INTEGER	read-only	Indicates the type of ATM VPN Interface that this path points to.
NUM stnAtmVpnTrunkPathNextIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.7	InterfaceIndex	read-only	The IfIndex of the destination ATM VPN Interface which this path entry refers to.
C64 stnAtmVpnTrunkPathInPackets	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.8	Counter64	read-only	The number of packets that have been received by the ATM VPN Trunk for this VPN path.
C64 stnAtmVpnTrunkPathInOctets	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.9	Counter64	read-only	The number of octets that have been received by the ATM VPN Trunk for this VPN path.
C64 stnAtmVpnTrunkPathOutPackets	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.10	Counter64	read-only	The number of packets that have been transmitted by the ATM VPN Trunk for this VPN path.
C64 stnAtmVpnTrunkPathOutOctets	1.3.6.1.4.1.3551.2.7.1.7.1.1.2.1.11	Counter64	read-only	The number of octets that have been transmitted by the ATM VPN Trunk for this VPN path.
stnAtmVpnLinkObjects	1.3.6.1.4.1.3551.2.7.1.7.1.2
stnAtmVpnLinkTable	1.3.6.1.4.1.3551.2.7.1.7.1.2.1		not-accessible	A list of ATM VPN Link entries.
stnAtmVpnLinkEntry	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1		not-accessible	Entry contains information about a particular ATM VPN Link.
NUM stnAtmVpnLinkIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.1	InterfaceIndex	read-only	The ifIndex of the ATM VPN Link Interface.
I32 stnAtmVpnLinkViId	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.2	Integer32	read-only	The instance of the configuration record corresponding to this ATM VPN Link.
STR stnAtmVpnLinkName	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.3	DisplayString	read-only	The name configured for this ATM VPN Link.
I32 stnAtmVpnLinkVpnOUI	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.4	Integer32	read-only	The Vpn OUI that is associated with this ATM VPN Link.
I32 stnAtmVpnLinkVpnIndex	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.5	Integer32	read-only	The Vpn Index that is associated with this ATM VPN Link.
I32 stnAtmVpnLinkVpnSubIndex	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.6	Integer32	read-only	The Vpn SubIndex that is associated with this ATM VPN Link.
INT stnAtmVpnLinkState	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.7	INTEGER	read-only	The current operational state of the ATM VPN LINK.
I32 stnAtmVpnLinkTrunkViId	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.8	Integer32	read-only	The instance of the configuration record corresponding to the ATM VPN Trunk associated with this ATM VPN Link. If the value is zero, then no ATM VPN Trunk is currently associated with this ATM VPN Link.
NUM stnAtmVpnLinkLowerIfIndex	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.9	InterfaceIndex	read-only	The ifIndex of the Interface below the ATM VPN Link Interface.
C64 stnAtmVpnLinkOutUnknownVpnId	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.10	Counter64	read-only	The number packets passed from an ATM VPN Trunk with a Vpn-Id that was appropriate for the ATM VPN Link's forwarding table.
C64 stnAtmVpnLinkOutVpnIdIfaceInvalid	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.11	Counter64	read-only	The number packets passed from an ATM VPN Trunk when no appropriate interface exists below this ATM VPN Link.
C64 stnAtmVpnLinkInVpnIdIfaceInvalid	1.3.6.1.4.1.3551.2.7.1.7.1.2.1.1.12	Counter64	read-only	The number packets received when there was no appropriate ATM VPN Trunk Interface present.

RFC description

Vendor-specific MIB for ATM VPN trunk management in Spring Tide Networks routers, manages ATM virtual private networks.

Start monitoring Spring Tide Networks (Lucent) multiservice ATM switch (ATM VPN interface config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download STN-ATM-VPN-MIB

What Is STN-ATM-VPN-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description